MDS-2009

Catalog

Digital Variable Multi Units Models: MDS 030 A(R) - MDS 070 A(R) MDS 080 B(R) - MDS 320 B(R)

MDS-2009

Table of Contents Nomenclature........................................................................................................................1 - Product Line-Up Features..............................................................................................................................15 Application Information........................................................................................................16 - Operating Range - Refrigerant Circuit Diagrams - Controllers - Installation Sound Data.........................................................................................................................67 Selection Process...............................................................................................................87 - Fan Performance Curves - EXV Engineering & Physical Data..............................................................................................96 - Specifications Performance Data.............................................................................................................138 - Performance Table Dimensional Data...............................................................................................................214 Electrical Data...................................................................................................................224 Wiring Diagrams................................................................................................................231 Servicing & Maintenance..................................................................................................255 Troubleshooting................................................................................................................256 Exploded View & Part List.................................................................................................261

Note : Installation and maintenance are to be performed only by qualified personnel who are familiar with local codes and regulations, and experienced with this type of equipment. Caution : Sharp edges and coil surfaces are a potential injury hazard. Avoid contact with them. Warning : Moving machinery and electrical power hazard. May cause severe personnel injury or death. Disconnect and lock off power before servicing equipment. “McQuay” is a registered trademark of McQuay International. All rights reserved. © 2009 McQuay International. All rights reserved throughout the world. Bulletin illustrations cover the general appearance of McQuay International products at the time of publication. We reserve the right to change design and construction specifications at any time without notice.

Nomenclature Wall Mounted G Series

Others C : Third Issue Type of grill A : Grill A Other Specifications L : Bare unit

Market Region C : Export with CE mark Electrical A : 220-240V/1Ph/50Hz

M

WM

D

009

-

G

A

C

L

A

C

Series G : G series (Common for cooling only and heatpump model) Capacity 009 : 9,000 Btu/h Model Type D : Indoor model for MDS Model Name WM : Wall Mounted Brand M : McQuay

1

Ceiling Cassette A and C Series

Product Specification Variation AA : Revision

Type of Connection F : For Flare

Electrical A : 220-240V/1Ph/50Hz

M

CK

D

010

C

-

A

F

A

Series A : A Series C : C Series (Common for cooling only and heatpump model)

Capacity 010 : 10,000 Btu/h Model Type D : Indoor model for MDS Model Name CK : Ceiling Cassette

Brand M : McQuay

2

A

Ceiling Concealed C Series Product Specification Variation AA : Revision

Type of Connection F : For Flare

Electrical A : 220-240V/1Ph/50Hz

M

CC

D

010

C

-

A

F

A

Series C : C Series (Common for cooling only and heatpump model)

Capacity 010 : 10,000 Btu/h Model Type D : Indoor model for MDS Model Name CC : Ceiling Concealed

Brand M : McQuay

3

A

Ceiling Convertible E Series

Others A : First Issue Other Specifications B : Bare model Controller Specifications G : Wireless Handset

Market Region C : Export with CE mark Electrical A : 220-240V/1Ph/50Hz

M

CM

D

020

E

-

A

C

G

B

A

Series E : E series (Common for Cooling only and Heatpump Model) Capacity 020 : 20,000 Btu/h Model Type D : Indoor model for MDS Model Name CM : Ceiling Convertible

Brand M : McQuay

4

Ceiling Convertible D/C Series

Product Specification Variation AA : Revision

Type of Connection F : For Flare

Electrical A : 220-240V/1Ph/50Hz

M

CM

D

040

D

-

A

F

A

A

Series C : C Series D : D Series (Common for cooling only and heatpump model)

Capacity 040 : 40,000 Btu/h Model Type D : Indoor model for MDS Model Name CM : Ceiling Convertible

Brand M : McQuay

5

Ducted Blower Others AA : Product Revision

Type of Connection F : For Flare

Electrical A : 220-240V/1Ph/50Hz

M

DB

D

080

-

10

-

A

External Static Pressure 10 : 100Pa

Capacity 080 : 80,000 Btu/h

Model Type D : Indoor model for MDS

Model Name DB : Ducted Blower

Brand M : McQuay

6

M

A

E

Outdoor

Others: E : Export

Product Specification Variation AA : Revision Electrical A : 220-240V/1Ph/50Hz F : 380-415V/3Ph/50Hz

MDS

040

A

R

-

A

A

A

Model Type R : Heatpump Omitted if Cooling Only

Series A : A Series B : B Series

Capacity 040 : 40,000 Btu/h

Model Name MDS : McQuay Multi Digital Scroll

7

-

E

MEX Box

Revision C : For all model except (MWMD-G) D : For MWMD-G only

Connecting Pipe Mode SAP : Flare fitting & nipple joint (Common for R22 and R410A Indoor)

Connecting Pipe Size 2 : 1/4 Inch (6.35mm) 3 : 3/8 Inch (9.52mm) 4 : 1/2 Inch (12.7mm)

MEX

-

15

-

2

SAP

-

C

Valve Opening Size 15 : Nominal diameter value (mm) X 10

Model Name MEX : McQuay Electronic Expansion Valve Junction Box

8

Product Line-up Indoor Unit MWMD-G Series Classification Control Module

Grill A

Nano Coated Filter

ACLAD

X

X

X

X

X

X

015G

ACLAD

X

X

X

X

X

X

020G

ACLAD

X

X

X

X

X

X

025G

ACLAD

X

X

X

X

X

X

Bare

010G

G11

X

G7

X

MC301

X

MDS MC201-C

X

MDS MC200-C

X

MDS MC201-A

X

MDS MC200-A

ACLAD

Nomenclature

Hydrophilic

Others

CE Mark

Fin Type

G17

Marking

009G

MWMD Std

Handset

MCKD-A Series Classification

Auto Air Swing

Others

X

X

X

X

025A

AFBD

X

X

X

X

X

030A

AFBD

X

X

X

X

X

040A

AFBD

X

X

X

X

X

050A

AFBD

X

X

X

X

X

9

G11

X

G7

AFBD

MC301

Bare

Hydrophilic

Fin Type

CE Mark

Marking

G17

MDS MC201-C

MDS MC200-C

MDS MC201-A

MDS MC200-A

Handset

020A

MCKD Std

Nomenclature

Control Module

MCKD-C Series Classification Others

Bare

X

X

X

X

X

015C

AFAD

X

X

X

X

X

020C

AFAD

X

X

X

X

X

Marking

Fin Type

G7

G11

AFAD

MC301

CE Mark

Auto Air Swing

Fin Type

Hydrophilic

Marking

G17

MDS MC201-C

MDS MC200-C

MDS MC201-A

MDS MC200-A

Handset

010C

MCKD Std

Nomenclature

Control Module

MCCD-C Series Classification

With Air Filter

With EPS Drain Pan

AFAD

X

X

X

X

X

X

020C

AFAD

X

X

X

X

X

X

025C

AFAD

X

X

X

X

X

X

030C

AFAD

X

X

X

X

X

X

040C

AFAD

X

X

X

X

X

X

050C

AFAD

X

X

X

X

X

X

060C

AFAD

X

X

X

X

X

X

10

Built in Filer Rail

Bare

015C

Hydrophilic

CE Mark

X

G17

X

G11

X

G7

X

MDS MC200-C

X

MDS MC201-A

X

MDS MC200-A

AFAD

Nomenclature

MC301

Others

010C

MCCD Std

Handset

MDS MC201-C

Control Module

040D

AFAD

X

X

X

X

X

050D

AFAD

X

X

X

X

X

062C

AFAD

X

X

X

Control Module

11

Handset Marking Fin Type

X

Auto Air Swing Convertible

X X X X X X

025E ACGBD X X X X X X

028E ACGBD X X X X X X

Bare

G11

G7

MC301

MDS MC201-C

MDS MC200-C

MDS MC201-A

MDS MC200-A

Fin Type

Convertible

Hydrophilic

ACGBD Marking

Auto Air Swing

Hydrophilic

CE Mark

020E Nomenclature

G17

MCMD

Handset

Bare

G11

Std

Control Module

G7

MC301

MDS MC201-C

MDS MC200-C

MDS MC201-A

MDS MC200-A

Nomenclature

CE Mark

MCMD

G17

Std

MCMD-E Series Classification Others

MCMD-D/C Series Classification

Others

CE Mark

Auto Air Swing

PLCKDA-NG17

X

X

X

PLCKDC-NG17

X

X

X

Std

12

Handset

080 10-AMAE X X X

100 15-FMAE X X X

Marking

With Air Filter

Marking

Hydrophilic

Handset

Bare

CE Mark

G17

G11

G7

MC301

MDS MC201-C

MDS MC200-C

MDS MC201-A

MDS MC200-A

Nomenclature

MDBD

Control Module

Convertible

G11

G7

MC301

Nomenclature

MCKD

G17

Std

MDBD Panel Classification Fin Type Others

MCKD Panel Classification

Others

Outdoor Unit MDS-A Series Classification

Gas Pipe Size (in)

X

X

X

3/8

5/8

X

X

X

X

3/8

3/4

AACE

X

X

X

X

X

X

FABE

X

X

X

X

X

X

3/8

3/4

AABE

X

X

X

X

X

X

FABE

X

X

X

X

X

X

X

3/8

3/4

070A

FAAE

X

X

X

X

X

X

X

3/8

3/4

030AR

ACCE

X

X

X

X

X

X

3/8

5/8

040AR

AABE

X

X

X

X

X

X

3/8

3/4

AACE

X

X

X

X

X

X

FABE

X

X

X

X

X

X

3/8

3/4

AABE

X

X

X

X

X

X

FABE

X

X

X

X

X

X

X

3/8

3/4

FAAE

X

X

X

X

X

X

X

3/8

3/4

050A 060A

050AR 060AR 070AR

X

X

13

Hydrophilic

X

X

Aluminium

X

X

Fixed Scroll

X

AABE

CE Mark

ACCE

040A

Phase Sequencer

Liquid Pipe Size (in)

Fin Type

Digital Srcoll

Compressor

Without Marking

Discharge Thermostat Protection

High Pressure Sensor

Low Pressure Sensor

Marking

030A

Nomenclature COOLING ONLY HEATPUMP

High Pressure Switch

MDS

Low Pressure Switch

Safety Devices

MDS-B Series Classification

Without Marking

Digital Srcoll

Fixed Scroll

Aluminium

Liquid Pipe Size (in)

Gas Pipe Size (in)

X

X

X

X

X

1/2

1-1/8

100B

FAAE

X

X

X

X

X

X

X

X

1/2

1-1/8

120B

FAAE

X

X

X

X

X

X

X

X

5/8

1-1/8

150B

FAAE

X

X

X

X

X

X

X

X

5/8

1-1/8

180B

FAAE

X

X

X

X

X

X

X

X

5/8

1-3/8

200B

FAAE

X

X

X

X

X

X

X

X

5/8

1-3/8

220B

FAAE

X

X

X

X

X

X

X

X

3/4

1-1/2

240B

FAAE

X

X

X

X

X

X

X

X

3/4

1-1/2

260B

FAAE

X

X

X

X

X

X

X

X

3/4

1-5/8

280B

FAAE

X

X

X

X

X

X

X

X

3/4

1-5/8

300B

FAAE

X

X

X

X

X

X

X

X

3/4

1-5/8

320B

FAAE

X

X

X

X

X

X

X

X

3/4

1-5/8

080BR

FAAE

X

X

X

X

X

X

X

X

1/2

1-1/8

100BR

FAAE

X

X

X

X

X

X

X

X

1/2

1-1/8

120BR

FAAE

X

X

X

X

X

X

X

X

5/8

1-1/8

150BR

FAAE

X

X

X

X

X

X

X

X

5/8

1-1/8

180BR

FAAE

X

X

X

X

X

X

X

X

5/8

1-3/8

200BR

FAAE

X

X

X

X

X

X

X

X

5/8

1-3/8

220BR

FAAE

X

X

X

X

X

X

X

X

3/4

1-1/2

240BR

FAAE

X

X

X

X

X

X

X

X

3/4

1-1/2

260BR

FAAE

X

X

X

X

X

X

X

X

3/4

1-5/8

280BR

FAAE

X

X

X

X

X

X

X

X

3/4

1-5/8

300BR

FAAE

X

X

X

X

X

X

X

X

3/4

1-5/8

320BR

FAAE

X

X

X

X

X

X

X

X

3/4

1-5/8

14

Hydrophilic

Discharge Thermostat Protection

X

CE Mark

Phase Sequencer

X

High Pressure Sensor

Low Pressure Sensor

X

Low Pressure Switch

FAAE

Nomenclature COOLING ONLY

Fin Type

080B

MDS

HEATPUMP

Marking Compressor

High Pressure Switch

Safety Devices

Features High Part Load Efficiency

Most air-conditioning system operates in the 30%~70% region. Integrated with the up-to-date technology, MDS is capable to modulate its supply capacity to meet all indoors requirement closely. This modulating capability enable the MDS system to offer high IPLV (Integrated Part Load Value) that conventional air-conditioner can never compete.

More Economical Operation

With high IPLV, MDS is able to operate at high Seasonal Energy Efficient Ratio (SEER) region. This indicates that MDS is able to supply the required capacity with lower power consumption, in other words, lower electricity bills.

Excellent Electromagnetic Compatibility

Unlike variable speed compressors air conditioners, MDS runs at a constant speed throughout the operation, thus there is NEGLIGIBLE electromagnetic interference. This unique feature eliminates the need for expensive electromagnetic suppression electronics required to ensure electromagnetic compatibility.

No conversion Lost

Comparing to the traditional inverter drive air-conditioner, MDS has eliminated the possibility of lost of energy during the conversion of power signal.

Precise Temperature Control

The ambient of the outdoor and indoor change frequently and this will affect the indoor cooling and heating load. With MDS system, using a unique control algorithm, the temperature is kept constant throughout the operation.

Excellent Dehumidifying Performance

The continuously operating compressor in the MDS system provides excellent dehumidifying performance, and hence able to reduce the indoor RH to a more desired level. With lower RH in the interior, the growth of the bacteria and fungus are inhabited.

Rapid Cooling and Heating Capability

The stage of the art heat-exchanger combining with the high efficiency compressor promotes rapid exchange between refrigerant and air, ensuring set temperature to be achieved faster compared to traditional air-conditioning system.

Intelligent Capacity Modulation

The MDS system operates in a stepless capacity modulation ranging from 10~100%. The modulation will closely match the demand capacity whereby contributing to high SEER ratings that no conventional air-conditioners can achieved.

Long Piping Design for Flexibility

Piping length between outdoor and indoor unit can be extended up to 150 meters. The height between outdoor unit and indoor unit can be extended up to 50 meters. The height difference between indoor units can be as high as 15 meters. This greatly reduces constraint and offers huge flexibility in system design.

Better Place Utilization

MDS uses the single outdoor multiple indoors combination. This concept has greatly reduced the outdoors units and enhances flexibility during installation.sign.

15

Application Information Operating Range Ensure the operating temperature is in allowable range.

Cooling only

Outdoor temp. (°CDB)

Cooling

48

Caution : The use of your air conditioner outside the range of working temperature and humidity can result in serious failure. 0

24

15

Indoor temp. (°CWB)

Heatpump Cooling

Heating

Outdoor temp. (°CDB)

Outdoor temp. (°CWB)

16 48

0

-15 15

21

27

15

Indoor temp. (°CDB)

24

Indoor temp. (°CWB)

16

Refrigerant Circuit Diagrams

MODEL: MDS 030/040/050/060A

Filter

Indoor unit 1

Outdoor heat exchanger

HPS

Outdoor

Filter

LPS Electronic expansion valve

PWM

Liquid receiver

Filter

Indoor unit n

Accumulator

Digital compressor

indoor

Filter

Dry filter Electronic expansion valve

Filter

High pressure switch

Electronic expansion valve

Accumulator

17

Filter

Indoor Unit\P2

Low pressure switch

Filter

Cooling flow

Filter Indoor side

PWM

Digital compressor

Heat exchanger

Electronic expansion valve

Indoor Unit\P1

MODEL: MDS 070A

MODEL: MDS 030/040/050/060AR

Four-way valve

HPS

Filter

Electronic expansion valve LPS

PWM

Check valve

Digital compressor

indoor

Dry filter

Filter

Filter

Indoor unit n

Liquid receiver

Cooling flow

Accumulator

Electronic expansion valve

Outdoor heat exchanger

Filter

Indoor unit 1

Outdoor

Heating flow Electronic expansion valve

MODEL: MDS 070AR

Filter

High pressure switch

Filter

Low pressure switch Electronic expansion valve Filter

Dry filter

Heating flow Cooling flow

Accumulator

18

Filter

Indoor Unit\P2

Indoor side

Digital compressor

PWM

EXV

One-way valve

Heat exchanger

Electronic expansion valve

Heat exchanger\P1

Four-way valve

MODEL: MDS 080/100/120B

Heat Exchanger

Ball Valve

Check Valve High Pressure Switch High Pressure Sensor

TH8

TH1

Pressure Tapping Point

Pressure Tapping Point Heat Exchanger

Low Pressure Sensor

Oil Seperator TH12

Accumulator Digital Compressor

Standard Compressor

Ball Valve

TH9 TH10

SCC(HIC»Ø·)

EXV4 ST9 Cap Tube

TH11

ST5

Drier

MODEL: MDS 080/100/120BR

Ball valve

Four-way valve

Filter

Pressure tapping point Oil separator

Low pressure sensor

High pressure switch

Heat exchanger

Pressure tapping point

Check valve

Check valve

Accumulator

Standard compressor

Digital compressor Filter

Electronic expansion valve

Electronic expansion valve

Capillary Dry filter

19

Ball valve

MODEL: MDS 150B

Heat Exchanger

Ball Valve

Check Valve High Pressure Switch High Pressure Sensor Pressure Tapping Point

Heat Exchanger

TH8

TH1

Pressure Tapping Point Low Pressure Sensor

Oil Seperator

Digital Compressor

Standard Compressor

Standard Compressor

TH12

Accumulator

Ball Valve

TH9 SCC(HIC»Ø·)

Cap Tube

TH11

TH10

EXV4ST9 ST5

Drier

MODEL: MDS 150BR

Four-way valve

Filter

Ball valve

Pressure tapping point

High pressure sensor High pressure switch

Oil separator

Low pressure sensor

Heat exchanger

Pressure tapping point

Check valve

Check valve Accumulator

Standard compressor Standard compressor Digital compressor Filter

Electronic expansion valve

Electronic expansion valve Capillary Dry filter

20

Ball valve

MODEL: MDS 180B

Ball Valve 4 Way Valve Ball Valve

Heat Exchanger

Heat Exchanger

Heat Exchanger

Heat Exchanger

Check Valve High Pressure Switch High Pressure Sensor Pressure Tapping Point

TH1

Pressure Tapping Point Low Pressure Sensor

Oil Seperator

Digital Compressor

Standard Compressor

Standard Compressor

TH12

Check Valve

Accumulator

TH9

Ball Valve SCC(HIC»Ø·)

Cap Tube

TH11

TH10

EXV4ST9 ST5

Drier

MODEL: MDS 180BR Check valve

Filter

Filter

High pressure sensor High pressure switch

Ball valve

Pressure tapping point Low pressure sensor

Heat exchanger

Pressure tapping point

Oil separator

Four-way valve

Heat exchanger

Four-way valve

Ball valve

Check valve

Electronic expansion valve

Accumulator Check valve

Standard compressor Standard compressor

D ig it a l c o m p r e s s o r Filter Electronic expansion valve Capillary Dry filter

21

Ball valve

MODEL: MDS 200/220/240B

Ball Valve 4 Way Valve Ball Valve

Heat Exchanger

Check Valve

Heat Exchanger

Heat Exchanger

High Pressure Sensor

TH1

Pressure Tapping Point

Pressure Tappign Point

Low Pressure Sensor

Oil Seperator

Digital Compressor

Standard Compressor

Standard Compressor

TH12 Standard Compressor

Heat Exchanger

High Pressure Switch

Accumulator

Check Valve TH9

Ball Valve TH10

SCC(HIC»Ø·)

EXV4 ST9 Cap Tube

TH11

ST5

Drier

MODEL: MDS 200/220/240BR Check valve

Filter

Filter

High pressure sensor High pressure switch Pressure tapping point

Oil separator

Four-way valve

Heat exchanger

Four-way valve

Pressure tapping point Low pressure sensor

Check valve

Electronic expansion valve

Heat exchanger

Check valve

Accumulator Oil crock Standard compressor Standard compressor

Standard compressor

Digital compressor Filter

Electronic expansion valve Capillary Dry filter

22

Ball valve

Ball valve

MODEL: MDS 260B

Heat Exchanger

Ball Valve

Check Valve High Pressure Switch High Pressor Sensor

TH8

TH1

Pressure Tapping Point

Pressure Tapping Point

Heat Exchanger

Low Pressure Sensor

Oil Seperator TH12 To Indoor Unit

Standard Compressor

Digital Compressor

Ball Valve Accumulator

oil tank

TH9

Check Valve

Ball Valve SCC(HIC»Ø·)

TH10

EXV4ST9 Cap Tube

TH11

ST5

Drier

Heat Exchanger

Ball Valve

High Pressure Switch High Pressure Sensor

TH8

TH1

Pressure Tapping Point

To Indoor Unit

Pressure Tapping Point

Oil Seperator

Standard Compressor

TH12 Ball Valve Standard Compressor

Standard Compressor

Heat Exchanger

Low Pressure Sensor

oil tank

Accumulator

Check Valve TH9

Ball Valve SCC(HIC»Ø·)

TH11

TH10

EXV4ST9 Cap Tube

ST5

23

Drier

MODEL: MDS 260BR

Master unit

Filter Ball valve

Four-way valve

Pressure tapping point

Check valve

High pressure switch

Oil separator

High pressure sensor

Low pressure sensor

Heat exchanger

Pressure tapping point

Check valve

Accumulator Ball valve

Standard compressor

Digital compressor Filter

Electronic expansion valve

Ball valve

Electronic expansion valve Capillary Dry filter

Filter Ball valve

Four-way valve

Slave unit

Pressure tapping point

Check valve

High pressure sensor High pressure switch

Oil separator

Low pressure sensor

Heat exchanger

Pressure tapping point

Check valve

Accumulator

Ball valve

Standard compressor Standard compressor Standard compressor Filter

Electronic expansion valve

Electronic expansion valve Capillary Dry filter

24

Ball valve

MODEL: MDS 280/300/320B

Check Valve High Pressure Switch High Pressure Sensor

TH1

Pressure Tapping Point

Heat Exchanger

Heat Exchanger

Ball Valve

Pressure Tapping Point Low Pressure Sensor

Oil Seperator

TH8

TH12

Digital Compressor

Standard Compressor

Standard Compressor

To Indoor Unit

Ball Valve Accumulator

TH9

Ball Valve SCC(HIC»Ø·)

TH10

EXV4ST9 Cap Tube

TH11

ST5

Drier

High Pressure Switch High Pressure Sensor Heat Exchanger

TH1

To Indoor Unit

Pressure Tapping Point

Pressure Tapping Point Low Pressure Sensor

Oil Seperator

TH8 Standard Compressor

TH12 Ball Valve Standard Compressor

Standard Compressor

Heat Exchanger

Ball Valve

oil tank

Accumulator

Check Valve TH9

Ball valve SCC(HIC»Ø·)

TH11

TH10

EXV4ST9 Cap Tube

ST5

25

Drier

MODEL: MDS 280/300/320BR

Filter

Four-way valve

Master unit

Ball valve

Pressure tapping point Check valve

Oil separator

High pressure sensor High pressure switch

Low pressure sensor

Heat exchanger

Pressure tapping point

Check valve

Accumulator

Ball valve

Standard compressor Standard compressor Digital compressor Filter

Electronic expansion valve

Ball valve

Electronic expansion valve Capillary Dry filter

Slave unit

Four-way valve

Filter Ball valve

Check valve

Pressure tapping point

High pressure sensor High pressure switch

Heat exchanger

Pressure tapping point

Oil separator

Low pressure sensor

Check valve

Accumulator

Ball valve

Standard compressor Standard compressor Standard compressor Filter

Electronic expansion valve

Electronic expansion valve Capillary Dry filter

26

Ball valve

Controllers

G17 Remote Controller

1

2

P1 P2

10

9

3

MODE

4

SLEEP

7

OFF TIMER

ON TIMER

13

14

SET

SET CANCEL

15

CANCEL

5

8 12

6a 6b

11

Operation Guide

1. Transmission Source The source where the signal will be transmitted. 2. Signal Transmission Indication Blink to confirm that the last setting has been transmitted to the unit. 3. Temperature Setting To set the desired room temperature, press the ▲ or ▼ button to increase or decrease the set temperature. The temperature setting range is from 16°C to 30°C (optional setting 20°C to 30°C). 4. Personalize Setting Press and hold for 3s, then

P1

will blink. Press again to cycle between

P1

and

P2

.

Set the desire setting, then leave the handset for 4s without pressing any key and it will save the setting into the programme. Press once to activate the P1 setting, press again to cycle between P1 and P2. Press any key to deactivate the personalize setting.

27

5. Automatic Air Swing (optional) Press the SWING button to activate the automatic air swing function. To distribute the air to a specific direction, press the SWING button and wait until the louver move to the desired direction and press the button once again. 6a. Silent Function Press for quiet operation. Fan speed turn to minimum speed. Press again to deactivate the function. 6b. Ionizer Function Press button to activate the negative ion function, which will refresh the indoor air effectively. 7. Sleep Mode Setting Press the SLEEP button will activate the sleep mode function. This function is available under COOL, HEAT and AUTO mode. When the unit is operating under cooling mode, the set temperature is increased by 0.5°C after 30 minutes, 1°C after an hour, and 2°C after 2 hours. When the unit is operating under heating mode, the set temperature is decreased by 1°C after 30 minutes, 2°C after an hour, and 3°C after 2 hours. 8. Operating Mode Press the MODE button to select the type of operating mode. For cooling only unit, the available modes are: COOL ( ), DRY (

) and FAN (

).

9. Fan Speed Selection Press the button continuously will toggle the fan speed in the following order: Low Med High Auto Stop pressing when the desired fan speed appears on the display screen. 10. “ON/OFF” Button Press one to start the air conditioner unit. Press again to stop the unit. 11. Timer Cancel Press the TIMER CANCEL button to cancel the on timer setting. 12. OFF Timer Setting Press the OFF TIMER button will activate the off timer function. Set the desired off time by pressing the OFF TIMER button continuously. 13. ON Timer Setting Press the ON TIMER button will activate the on timer function. Set the desired on time by pressing the ON TIMER button continuously. If the timer is set to 7.30am, the air conditioner will turn on at 7.30am sharp. 14. Turbo Function Press for fast cooling. Fan speed turn to maximum speed. Press again to deactivate the function. 15. Clock Time Setting Press and hold to set the clock time.

28

MC301 Wired Controller

1. “ON/OFF” switch • Press to start the air conditioner unit. • Press again to stop the unit. 2. Temperature setting • Set the desired room temperature. • Press button to increase or decrease the set temperature. Setting range are between 16°C to 30°C (61°F to 86°F). 3. Operation Modes • Press the ‘Mode’ button to select the type of operating mode. • When the outdoor unit is OFF: - Cooling Only: COOL, FAN, DRY - Heat Pump: COOL, HEAT, FAN, DRY • When the outdoor unit is in COOL: COOL, FAN, DRY • When the outdoor unit is in HEAT: HEAT, FAN 4. Fan Speed Selection • Press the button until the desired fan speed is achieved.

29

5. “Sleep” mode • Press button to activate the sleep function. This function can only be activated under COOL or HEAT mode operation. 6. “Heater/Swing” • For ducted model, press the button to activate the auxiliary electric heater (if applicable). • For non ducted model, press the button to activate the automatic air swing function. 7. Timer • Press button to enter the timer setting of the air conditioner unit. • When the unit is ON, ‘OFF’ timer can be selected and set. • When the unit is OFF, “ON’ timer can be selected and set. • Press “ ” to increase in hour and press “ ” to increase in minute. 8. Reset • Press to restart the unit. 9. Other Function Key Lock • Press the “Sleep” button and hold for 5 seconds to activate the key lock. At this point, only the “ON/OFF” button is valid. • To disable the key lock, press the “Sleep” button and hold for 5 seconds. Temperature Unit Setting • Press “Fan” button and hold for 5 seconds to change the temperature unit (from °C to °F or from °F to °C).

30

MC 303 Centralized Controller

LCD vision window POWER RUN ON/OFF

CLK Button Reset Button ENTER

FAN

MODE

TIMER

SWING

UNIT NO.

SETUP

HEATER

SLEEP

TEMP

Features: • Used in R410A multi digital scroll system. • Group control setting: ON/OFF, temperature, mode, fan speed and sleep for 32 units at the same time. • Individual control setting: ON/OFF, temperature, mode, fan speed and sleep. • Timer setting: timer ON/OFF all units. • Display: display each unit temperature, mode, fan speed, running and fault code one by one. • Real time clock: Using back-up battery to maintain the real timer. Individual Control Setting: At display status, press “UNIT NO.” key, there is no unit number display on LCD panel, then press “∆” or “ ” key to select unit number, press the “ENTER” key to confirm. The unit status will display on LCD panel and the unit number is blinking. Now you can operate the unit. • “ON/OFF” switch - Press to start the air conditioner unit and press again to stop the unit. • Mode setting - Press the “MODE” key to select the type of operating mode. - When the outdoor unit is OFF: Cooling only: COOL FAN DRY COOL Heat Pump: COOL HEAT FAN DRY COOL - When the outdoor unit is in COOL: COOL FAN DRY COOL - When the outdoor unit is in HEAT: HEAT FAN HEAT • Temperature setting - Press “∆” or “ ” key to increase or decrease by 1°C or 1°F. Setting range are between 16°C to 30°C (61°F to 86°F). ∆

∆

31

• Fan speed setting - Press “FAN” key until the desired fan speed is achieved. The indoor fan speed are High Auto Low Medium High. - No AUTO speed when it is in FAN mode. • “Swing” setting - Press “SWING” key to activate the automatic air swing function. • “Sleep” mode - Press “SLEEP” key to activate the sleep function. - This function can only be activate under COOL or HEAT mode operation. • Key Lock - Press “MODE” key and hold for 5 seconds, ‘ ’ will display on LCD panel and key lock function is activated. - To disable the key lock, press the “MODE” key for 5 seconds. Group Control Setting: At display status, press “UNIT NO.” key then follow by “∆” or “ ” key until the symbol “–– ––” appeared. Press the “ENTER” key to confirm. The symbol “–– ––” is blinking and you may operate group control. • Group “ON/OFF” - At display status, press and hold “ON/OFF” key for 5 seconds until the unit number is blinking and the symbol “[ ]” appeared. Press “ON/OFF” key to start or stop all units. - Alternative way, press “UNIT NO.” key then follow by “∆” or “ ” key until the symbol “[ ]” appeared. Press the “ENTER” key to confirm. The symbol “[ ]” is blinking and you may ON/OFF off all units. • Mode setting - Press the “MODE” key to select the type of operating mode. - When the outdoor unit is OFF: COOL HEAT AUTO FAN DRY COOL • Temperature setting - Press “∆” or “ ” key to increase or decrease by 1°C or 1°F. Setting range are between 16°C to 30°C (61°F to 86°F). • Fan speed setting - Press “FAN” key until the desired fan speed is achieved. The indoor fan speed are High Auto Low Medium High. - No AUTO speed when it is in FAN mode. • “Swing” setting - Press “SWING” key to activate the automatic air swing function. • “Sleep” mode - Press “SLEEP” key to activate the sleep function. - This function can only be activate under COOL or HEAT mode operation. • Key Lock - Press “MODE” key and hold for 5 seconds, ‘ ’will display on LCD panel and key lock function is activated. - To disable the key lock, press the “MODE” key for 5 seconds. • Real Time Clock - Press “CLK” to enter week setting. Press “∆” or “ ” to select from Sunday to Saturday - Press “CLK” again, the “CLOCK SET” symbol will display and the symbol “__:__” is blinking. At this time, press “∆” to increase the hours and follow by “ ” to increase minutes. - It will automatically disable the real time clock setting after 5 seconds if there is no any (“∆” , “ ” and “CLK”) key is pressed. Press any other key to disable the real time clock setting. • Timer - The Timer setting procedure as follow: i) Press “TIMER”, “WEEK SET” and “TIMER SET” appear on the bottom left of LCD panel. Press “∆” or “ ” to select day (Sunday to Saturday) and press “TIMER” again to confirm the selection. Once confirmed, the timer’s states of the selected day will display on LCD panel. ii) Enter first timer setting, the timer ON or OFF symbol will display on the bottom left of LCD panel, the timer sequence number “1” will appear on the top of LCD, press “∆”or “ ” to select timer sequence number. Press “TIMER” again to confirm the selection followed by entering the ON timer and OFF timer setting.

32

iii) Press “∆” or “ ” to select ON timer or OFF timer and press “TIMER” to enter time setting. iv) “TIMER SET” and “CLOCK SET” will display on the bottom left of the LCD panel, press “∆” to set hour and press “ ” to set minute. Press “TIMER” again to complete timer setting and/or enter next timer setting, repeat above procedure until all timer setting are finished. • Reset - Press to restart the unit. • Temperature Unit setting - The temperature unit setting can be done via: i) The controller PCB board DIP switch setting. When DP1 is “ON”, the unit is °F. When the DP1 is “OFF”, the unit is °C. ii) Press and hold “FAN” for 5 seconds until the beep sound and the unit will alter between °C or °F.

33

Error Codes for MDS A Series

Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Code E0 E1 E2 E3 E4 E5 E6 E7 E8 H1 H2 H3 L1 C- CX

Description Sensor broken (TH1 discharge temp.) Sensor broken (TH2 ambient temp.) Sensor broken (TH3 return air temp.) Compressor bottom sensor broken Sensor broken (TH4 coil inlet temp.) Sensor broken (TH5 mid coil temp.) Sensor broken (TH6 outlet coil temp.) Discharge temp. too high (>130°C) System malfunction Compressor high pressure trip Digital compressor overload Fixed compressor overload Compressor low pressure trip Outdoor and indoor communication error #X indoor and outdoor communication error

Error Codes for MDS B Series Item

Code

Description

Item

Code

Description

0

EC00

00# indoor unit communication failure

62

EC62

Refrigerant released

1

EC01

01# indoor unit communication failure

63

EC63

Slaver outdoor unit communication failure

2 - 47

‌

02 - 47# indoor unit communication failure

64

ER64

TH1 temperature sensor failure

48

ER48

Digital compressor overload

65

ER65

TH2 temperature sensor failure

49

ER49

Fix 1 compressor overload

66

ER66

TH3 temperature sensor failure

50

ER50

Fix 2 compressor overload

67

ER67

TH4 temperature sensor failure

51

ER51

Fix 3 compressor overload

68

ER68

TH5 temperature sensor failure

52

ER52

Discharge pressure is too high

69

ER69

TH6 temperature sensor failure

53

ER53

Suction pressure is too low

70

ER70

TH7 temperature sensor failure

54

ER54

Outdoor unit's IC error

71

ER71

TH8 temperature sensor failure

55

ER55

System Error

72

ER72

TH9 temperature sensor failure

56

ER56

Discharge temperature is too high

73

ER73

TH10 temperature sensor failure

57

ER57

-

74

ER74

TH11 temperature sensor failure

58

ER58

4 way valve failure

75

ER75

TH12 temperature sensor failure

59

ER59

Ambient temperature is beyond the limit

76

ER76

Discharge pressure sensor failure

60

ER60

Emergency running

77

ER77

Suction pressure sensor failure

61

ER61

Subheating is beyond the limit

78

ER78

All indoor units communication failure

34

MC 301 Error Code Item Code Description

Item Code

Description

Item Code

Description

1

E0

System malfunction

23

F8

4wv malfunction

45

16

Sensor broken( slave TH6 inlet coil 3#)

2

E1

Sensor broken (TH1 discharge temp)

24

F9

Refrigerant leakage

46

17

Sensor broken( slave TH7 mid coil 3#)

3

E2

Sensor broken (TH2 inlet coil 1#)

25

FA

Controller storage malfunction

47

18

Sensor broken (slave TH8 ambient temp.)

4

E3

Sensor broken (TH3 mid coil 1#)

26

FB

Water pump(indoor drain pump)

48

19

Sensor broken( slave TH9 outlet coil)

5

E4

Sensor broken (TH4 inlet coil 2#)

27

FC

Indoor and outdoor communication malfunction

49

1A

Sensor broken( slave TH10 subcool outlet)

6

E5

Sensor broken (TH5 mid coil 2#)

28

FE

Master and slave communication malfunction

50

1B

Sensor broken( slave TH11 subcool suction)

7

E6

Sensor broken (TH6 inlet coil 3#)

29

H0

Digital comp overload

51

1C

Sensor broken( slave TH12 suction)

8

E7

Sensor broken (TH7 mid coil 3#)

30

H1

Fixed comp1 overload

52

1F

Emergency run

9

E8

Sensor broken (TH8 ambient temp..)

31

H2

Fixed comp2 overload

53

20

Outdoor storage malfunction

10

E9

Sensor broken (TH9 outlet coil)

32

H3

Fixed comp3 overload

54

27

Ambient temp.. exceed the limit

11

EA

Sensor broken (TH10 subcool outlet)

33

H4

High pressure too high

55

28

4wv malfunction

12

EB

Sensor broken (TH11 subcool suction)

34

H5

Sensor broken, high pressure

56

29

Refrigerant leakage

13

EC

Sensor broken (suction)

35

H6

Discharge temp. too high

57

30

Digital comp overload

14

EF

Emergency run

36

L0

Super heat too low

58

31

Fixed comp1 overload

15

F0

Outdoor storage malfunction

37

L1

Low pressure too low

59

32

Fixed comp2 overload

16

F1

Sensor broken (indoor inlet coil)

38

L2

Sensor broken, low pressure

60

33

Fixed comp3 overload

17

F2

Sensor broken (indoor mid coil)

39

10

System malfunction

61

34

High pressure too high

18

F3

Sensor broken (indoor outlet coil)

40

11

Sensor broken (slave TH1 discharge temp.)

62

35

Sensor broken, high pressure

19

F4

Sensor broken (indoor return air )

41

12

Sensor broken( slave TH2 inlet coil 1#)

63

36

Discharge temp. too high

20

F5

Sensor broken (indoor supply air)

42

13

Sensor broken( slave TH3 mid coil 1#)

64

40

21

F6

Indoor and controller communication malfunction

43

14

Sensor broken( slave TH4 inlet coil 2#)

65

41

Low pressure too low

22

F7

Ambient temp. exceed the limit

44

15

Sensor broken( slave TH5 mid coil 2#)

66

42

Sensor broken, low pressure

35

Super heat too low

Indoor Unit Malfunction Code F1

Sensor broken (indoor inlet coil)

F2

Sensor broken (indoor mid coil)

F3

Sensor broken (indoor outlet coil)

F4

Sensor broken (indoor return air )

F5

Sensor broken (indoor supply air)

F6

Indoor and controller communication malfunction

FA

Controller storage malfunction

FB

Water pump(indoor drain pump)

FC

Indoor and outdoor communication malfunction

Indication Light Twinkle Related To Malfunction Code: Type

Heat

Sleep/Fan

Time/Dry

Sensor broken (indoor temp.)

OFF

OFF

F

Indoor Water pump

OFF

F

OFF

F

OFF

OFF

OFF

F

F

Overload, Compressors, Digital/fixed

F

F

OFF

Pressure, Too high/too low

F

OFF

F

Pressure sensor, Outdoor

F

F

ON

System malfunction

F

F

F

Other malfunctions

F

ON

ON

Indoor and outdoor communication malfunction Sensor broken (outdoor temp.)

NOTES: 1. THE MODE CONFLICTION ALARM IS CANCELED, AS IT IS NOT A MALFUNCTION, BUT A LIMITING OPERATION. WHEN THE MODE CONFLICTION OCCURS, THE INDOOR UNIT STOPS DIRECTLY WITHOUT MAKING ALARM. 2. THE INDOOR AND OUTDOOR COMMUNICATION MALFUNCTION ONLY BELONGS TO THIS UNIT. 3. SIMPLIFY THE LIGHT TWINKLE INDICATION, AND THE INDOOR AND OUTDOOR MALFUNCTION CONTAINS MASTER AND SLAVE UNIT.

For Example:

0:

1:

2:

3:

4:

5:

6:

7:

8:

9:

A:

B:

C:

D:

E:

F:

H:

L:

N:

P:

R

T:

U:

Y

36

Installation

(1) Installation of Indoor Unit Preliminary Site Survey • Electrical supply and installation is to confirm to local authority’s (e.g. National Electrical Board) codes and regulations. • Voltage supply fluctuation must not exceed ± 10% of rated voltage. Electricity supply lines must be independent of welding transformers which can cause high supply fluctuation. • Ensure that the location is convenient for wiring, piping and drainage.

MWMD-G Series Indoor Unit

Figure A

37

Standard Mounting Install the unit at a location with the following requirements • No obstruction of air flow into and out of unit where cooler air can be evenly distributed as shown in Figure B. • Ensure that air discharge is not short circuited with air intake. • Ensure that wall is sufficiently strong, rigid, flat, perpendicular and vibration free. • Where air filter cassette can be slides in or out easily. • Where there is no danger of flammable gasses. • Where there is no direct sunlight on unit. • Also to take into consideration a place for the installation of the wireless LCD remote controller.

MAINTENANCE & SERVICING SPACE. AIR FLOW DIRECTION CAUTION : Do not install unit near the door way because excessive fresh air may cause panel condensation on the unit.

Figure B

38

Mounting Plate Installation CAUTION: i) Please check the unit weight for each model. Always ensure that the wall is sufficiently strong to withstand the weight. If not, it is necessary to reinforce the wall with plate, beams or pillars. ii) The unit cannot be directly fixed onto the wall or the likes. In all cases, the installation plate provided MUST be used. • Paste the installation plan provided on the desired location on the wall and marks the holes location accordingly. • Ensure that the minimum maintenance and servicing space at the top, left and right side of the unit is reserved. • Ensure also the levelness of the installation plate. • Drill the screw mounting holes (minimum 4 screws are required). • Drill the pipe hole at the location as per plan. (This is only applicable for rear piping outlet installation). Note: The hole should be drilled slightly lower at outdoor side as per Figure C.

Indoor Side

Outdoor Side

Figure C

• Fix the installation plate firmly to wall, without tilting to left or right. Use a plumb line, if available. Screw position in the wall

Dimension ‘A’ 350.0mm 400.0mm

72.0

Model MWMD 009G MWMD 010/015G

Dia 65.0mm Hole in the wall 'A'

'A'

Screw position in the wall

Model MWMD 020/025G

Ø 65.0 mm Hole in the wall

39

• Fixed method:Reinforced Concrete Building

Wooden Frame Wall

Nut Anchor

Bolt Anchor

Indoor Unit Preparation • Carefully bend the pipes to the required position to align with the hole. For right hand and rear side draw out, hold the bottom of the piping and fix direction before shaping it to the desired position (see Figure E). The condensation drain hose should be taped to the pipes with vinyl tape. The electrical cable can also be taped to the pipes.

• The refrigerant piping can be routed to the unit in 5 directions, by using the cut outs in the unit casing. (See Figure D)

1

3

2

4 5

Figure D

Figure E

Mounting Indoor Unit Hook the indoor unit onto the upper portion of installation plate. (Engage the 2 hooks of rear top of the indoor unit with the upper edge of the installation plate). Ensure the hooks are properly seated on the installation plate by moving in left and right.

Water Drainage Piping The indoor drain pipe must be downward gradient for smooth drainage. Avoid situation as shown in Figure F.

Water Leaking

Water Leaking

Water Leaking

End Dipped Into Water

Drain Correct

Wrong

Wrong

40

Wrong

MCKD-A/C Series

Min 0.5 m

Min 0.5 m

Min 0.5 m

Max. 0.3 m

Max. 3.0 m

Beam

Standard Mounting Install the unit at a location with the following requirements • The indoor unit must be installed in such that free from any obstacles in path of cool air discharge and warm air return, and must allow spreading or air throughout the room (near the center of the room). • Clearance must be provided for the indoor unit from the wall and obstacles as shown in Figure F.

Obstacles Floor

Figure F • The installation place must be strong enough to support a load of 4 times the indoor unit weight to avoid amplifying noise and vibration. 15.0

538.0

18.0

32.0 Piping Direction

448.0

505.0

Unit size 820.0 mm

UNIT

620.5 mm (hanging rod)

Unit size 820.0 mm

890.0 mm (ceiling opening)

88.0

790.0 mm (hanging rod)

529.0

580.0 ~ 610mm (CEILING OPENING MEASUREMENT)

38.0

890.0 mm (ceiling board opening)

19.0

580.0 ~ 610mm (CEILING OPENING MEASUREMENT)

MCKD-A Series

MCKD-C Series

• The indoor unit must be way from heat and steam sources (avoid installing it near an entrance). • Measure and mark the position for the hanging rod. Drill the hole for the angle nut on the ceiling and fix the hanging rod. • The installation template is extending according to temperature and humidity. Check on dimensions in using. • The dimensions of the installation template are same as those of the ceiling opening dimensions. • Before ceiling laminating work is completed, be sure to fit the installation template to the indoor unit. Note: Be sure to discuss the ceiling drilling work with the installers concerned.

41

Hanging Indoor Unit

Indo or U nit Ceiling Board 35.0 mm (MCKD-A) 30.0 MM (MCKD-C)

• Confirm the pitch of the hanging rod is 790.0mm x 620.5mm. • Hold the unit and hand it on the hanging rod with the nut and washer. • Adjust the unit height to 35.0mm (MCKD-A) or 30.0mm (MCKD-C) between the indoor unit bottom surface and the ceiling surface. • Confirm with a level gauge that the unit is installed horizontally and tighten the nut and bolt to prevent unit falling and vibration. • Open the ceiling board along the outer edge of the paper installation template. Water Drainage Piping • Drain pipe must be downward gradient for smooth drainage. • Avoid the drain pipe from up and down slope to prevent reversal flow. • During the drain pipe connection, be careful not to exert extra force on the drain connector at the indoor unit. • The outside diameter of the drain connection at the flexible drain hose is 20mm. • Be sure to provide heat insulation (polyethylene foam with thickness more than 8.0mm) on the drain piping to avoid the condensed water dripping inside the room.

INDOOR UNIT

Pipe clamp

Good

FEED WATER

Bad

• Connect the main drain pipe to the flexible drain hose. • Feed water from flexible drain hose and check the piping for leakage. • When the test is completed, connect the flexible drain hose to the drain connector on the indoor unit.

MAIN DRAIN PIPE

FLEXIBLE DRAIN HOSE

Note: This indoor unit use drain pump for condensed water drainage. Install the unit horizontally to prevent water leakage or condensation around the air outlet.

42

Panel Installation • The front panel can only be fitted in one direction, follow the piping direction. (Follow piping arrow sticker on the front panel). • Be sure to remove the installation template before installing the front panel.

• Open the air intake grille by pulling back the catchers and remove it together with filter from panel. • Install the front frame panel onto the indoor unit by using 4 screws and tighten it completely to prevent cool air leakage. • Connect the LED wire and air swing wire to the indoor unit.

Note: Install the front frame panel firmly to prevent cool air leakage which will cause condensation and water dripping.

43

MCMD-E Series Standard Mounting Ensure that the overhead supports are strong enough to hold the weight of the unit. Position the hanger rods (wall mounting bracket for floor standing), and check for its alignment with the unit as shown in Figure G. Also, check that the hangers are secured and the base of the fan coil unit is leveled in both horizontal directions, taking into account the gradient for drainage flow as recommended in Figure H.

Figure G

44

Please ensure that the following steps are taken: • Check the gradient for drainage flow as recommended in Figure H. • Provide clearance for easy servicing and optimal air flow as shown in Figure I. • The indoor unit must be installed such that there is no short circuit of the cool discharge air with the warm return air. • Don not install the indoor unit where there is direct sunlight shining on the unit. The location should be suitable for piping and drainage installation. The unit must be a large distance away from the door.

Figure H

Under ceiling type

Floor standing type

Figure I

45

Under Ceiling Installation Install the Suspension Bolts 1. Install the suspension bolts so that it can support the indoor unit. 2. Adjust the distance to ceiling before installation. 3. Refer to the dimension given (Figure G) to install the unit. Install the Indoor Unit 1. Insert the suspension bolts into the fittings of the hanger bracket. 2. Set the nuts and washer on the both side of the metal fittings. 3. Secure it with nuts. 4. Attach the hanger cover (4 pcs) to the units.

46

Floor Standing Installation

1. Refer to the dimension as illustrated when installing the mounting bracket. 2. Determine the pipe hose position using the rear piping hole. Drill the pipe hole at the slight downward slant to the outdoor side.

MOUNTING BRACKET

HOCK THE UNIT ON THE MOUNTING BRACKET

WALL

47

Piping and Drain Hose Installation Under Ceiling Type 1. The piping direction can be 2 ways as illustrated. 2. The drain hose is only 1 way.

OR

Floor Standing Type

OR

How to Install the Drain Hose 1. Remove the 2 screws and the drain pipe holder. 2. Cut a slit for the drain hose hole. 3. Place the drain hose on the v-shape area and secure it with drain pipe holder and 2 screws.

48

How to Remove the Air Inlet Grille 1. Remove the air inlet grille by both hands as the direction shown. 2. Loosen the screws for fixing the panel arm (3 screws – Left, Right and Center). Do not remove the screws at this time. 3. Move the air inlet grille upward, and then turn it backwards. (Do not use too much force). 4. Remove the grille holder (both left and right side). After that, remove the air intake grille. 5. Remove the grille holder (center) from the panel.

49

How to Install the Air Filter

To Adjust the Vane Direction Adjust the vane linkage as the direction shown to get the required vane direction.

70.0

Dimension of the Fresh Air Intake Hole

64.0

70.0

50

3.0

MCMD-C/D Series Standard Mounting Ensure that the overhead supports are strong enough to hold the weight of the unit. Position the hanger rods (wall mounting bracket for floor standing), and check for its alignment with the unit as shown in Figure J and Figure K. Also, check that the hangers are secured and the base of the fan coil unit is leveled in both horizontal directions, taking into account the gradient for drainage flow as recommended in Figure L.

A 1714

Model MCMD 040/050D

B 666

C 273

D 130

E 1636

F 39

Figure J

Model MCMD 062C

A 1750

B 40

C 36

D 1903 Figure K

51

E 1830

F 680

G 352

H 292

L 250

MCMD 040/050D

MCMD 062C

Figure L Please ensure that the following steps are taken: • Check the gradient for drainage flow as recommended in Figure L. • Provide clearance for easy servicing and optimal air flow as shown in Figure M. • The indoor unit must be installed such that there is no short circuit of the cool discharge air with the warm return air. • Do not install the indoor unit where there is direct sunlight shining on the unit. The location should be suitable for piping and drainage installation. The unit must be a large distance away from the door. • In case the unit is to be half recessed into false ceiling, please check the unit is well align.

MCMD 040/050D

52

MCMD 062C Figure M

Figure M • Provide the installation space as shown in Figure N.

MCMD 040/050D

MCMD 062C

Figure N

53

Under Ceiling Installation Step 1 Remove air intake grille, side panel, and side close-up and hanger bracket from the unit (see Figure O).

Figure O Step 2 Position the hanger rods as per Figure L and install the hanger bracket (see Figure P).

Figure P

Step 3 Hanger up the unit and tighten the bolt, after completed the piping and drain pipe; install back the grille and panel (see Figure Q).

Figure Q

54

Floor Standing Installation Step 1 Remove air intake grille, side panel and side close-up panel from the unit (see Figure O). Step 2 Position the floor support (field supply) as per Figure L and install the unit (see Figure R).

Figure R

Step 3 Two types of piping and drain pipe connection as Figure S.

Figure S

55

MCCD-C Series Standard Mounting Ensure the support is strong enough to withstand the weight of the unit and use the hanger supplied with the unit. Use the supplied drain socket to connect the drain pipe (the drain socket is only available for MCCD 010 to 025C). Install the unit in such a way that the condensate water can flow out smoothly.

The diagrams below show the screws position for duct work connection.

56

(2) Installation of EXV Box All models of this series product need connect a EXV box to finish the piping installation. The EXV box contains electronic expansion valves, which needs to be mounted in proper place on the liquid piping. When installing the EXV box, make sure the box vertical. The EXV box and the indoor unit could not exceed the length-limit of the electric expansion valve cable, as shown in the figure below. There are some manners to install the EXV box (the mounting must be fixed and safe, and the direction must be vertical).

indoor unit

flare joint EXV box liquid pipe gas pipe

Installation mode 1: Rod mounting

Pole

Nut Spring pad Hook screw hole Washer

Nut

Installation mode 2: Mounting on the wall

Fix with screw

57

Washer Hook

(3) Installation of Outdoor Unit Location for Installation To ensure good performance of the units, use the following guidelines to choose suitable location to install units: • Installation base must be strong enough to support the untis and prevent vibration. • To avoid installing units at dirty and salty place. • Do not install units at easy burning gas leakage place. Accumulated burning gas leakage may result in an explosion. • Do not install units to places where the units are inclined to be damaged by typhoon and strong wind. If possible, install rainproof, snow-shield, and lightproof equipment. • Ensure sufficient space for installation (see Figure T and Figure U). • Remove any barrier of air ventilation to both air supply and air discharge. • Maintain good ventilation for better heat exchange efficiency. Single Outdoor Unit

AIR OUTLET GUIDE 45¡ª

300mm

1000mm

450mm

FRONT

450mm+h3

100mm+h4

450mm

h4

h3

FR ONT

Figure T

58

FRONT

FRONT

FRONT

FRONT

BACK

BACK

900mm

BACK

900mm

BACK

450mm

More Than One Outdoor Unit

Figure U

Unit Handling Use 4 supporting points to move units instead of 3 points to avoid unstable move resulting units drop off. Suspension ropes (2 ropes)

Protective pads

< 40

<40

>8 m

>8m

59

Combined Outdoor Units Two outdoor units can be grouped as one outdoor unit (such as MDS260/280/300/320B/BR), to connect with indoor units. The installation of combined units is more complicated than that of the single outdoor units: 1. Select one unit as the master unit, the other one as the slave unit. These two units shall be positioned in the same level side by side. The distance between the master unit and slave unit cannot be more than 10mm. 2. Accessory copper parts are packed with the outdoor units. Pipe connection includes gas, liquid and balance piping connection between the master and slave units. All pipes shall be with insulation material and avoid any damage of this insulation material. 3. Gas and liquid pipe shall be connected parallel. The dimensions of the straight pipe connected to the Tri-joint must meet the requirements below:

(Remove the panel before connecting pipe) Position to connect pipe position

Master and slave units must be installed in the same level

A

To units

A >10mm

To units

C >500mm

Bala

nce

Liqu

id pip

Gas

B >200mm

B

pipe

D>100mm

e

pipe Tri-joint

Elbow

For 28.6mm gas pipe, directly connect to Tri-joint; For 34.9mm gas pipe, add a reducer and a transition pipe

Con n indo ect pipe or un to its

C

D 28.6mm a transiton pipe (only for 34.9mm gas pipe)

60

4. Balance pipe connection • Balance pipe must be installed. Balance pipe shall be connected through the hole of side panel or base panel or the position with the other outdoor unit. • Balance pipe shall be installed horizontally and orderly, and shall be lower than the access valve for balance pipe. • Protect the balance pipe carefully and avoid touching any other parts, especially need to keep the pipe from touching the wall of hole.

Side panel hole

Access valve for balance pipe( 9.52)

Base panel hole

Screw join

t

Balance pi

pe

5. All connecting pipe must be well insulated and well protected to avoid any rubbing with the surrounding cause by vibration.

61

(4) Refrigerant Piping Maximum Piping Length The refrigerant piping limit is show as below: 030-050 A/AR

060-070 A/AR

080-100 B/BR

120-320 B/BR

Piping Section

100

125

250

350

L1+L2+...L6+a=b...i

50

70

125

150

L1+L2+...L6+i

60

80

150

200

25

30

40

L3+L4+L5+L6+i

Outdoor above

20

30

50

--

Indoor above

20

30

40

--

Length (m)

Height

Piping

Total equivalent length Actual piping length Equivalent length Maximum equivalent length from first branch to furthers unit Between further indoor and outdoor

Maximum height between indoor unit

15

--

Note: The equivalent length is calculated as follow: One refnet joint equals to 0.5m, one distributor kit equals to 0.1m The above table is based on MDS 080/100B/BR unit. Outdoor unit

D3

Refnet of gas side

Refnet of liquid side

Refnet of liquid side

Gas valve L1 D1

D1

L2

D1

D3 Throttle unit

D4

D2

D4

b

D2

D4

c

D2

d

Indoor unit The max. equivalent length L The max. equivalent length L from the first refnet joint to the indoor unit L D1

D1 L3

D1 L4

D2

D1

L5

D4

D2

f

L6

D3

D3

D3 D4

e

Equivalent length =

D4

D2

a

D4

D2

g

D4

D2

h

D4

D2

Height between indoor unit and outdoor unit H2

The height between outdoor unit and indoor unit H1

Liquid valve

Refnet of gas side

i

actual pipe length + (number of elbows X equivalent length of each elbow) + (number of oil traps X equivalent length of each oil trap)

62

The equivalent length for each piping size, elbow and elbow are tabulate as below: Diameter (mm)

Item

Elbow (m)

9.52 12.70 15.88 19.02 22.02 25.40 28.58 31.80 ~ 41.30

Oil Trap (m)

0.18 0.20 0.25 0.35 0.40 0.45 0.50 0.55

1.3 1.5 2.0 2.4 3.0 3.4 3.7 4.0

When the equivalent length is more than 90% of the actually allowable maximum piping length (i.e. more than 63m for MDS060A/AR), the gas pipe diameter of the main piping (piping from the outdoor unit to the first branch) should be one size up. If the diameter of gas pipes needed to be sized up, the equivalent length should be recalculate as follow: New equivalent length = equivalent length of main piping X 0.5 + equivalent length of the branch pipe Refnet Joint and Distributor Kit Installation • Refrigerant piping should use the appointed diameter pipe. • Refnet joint must be installed horizontally or vertically.

(Horizontal line) A viewer

In ±15˚

OR In ±15˚

(Horizontal line) B viewer

• Distributor kit must be installed horizontally.

Liquid distributor kit Gas distributor kit To the indoor unit

To the indoor unit

Horizontal line B viewer B viewer

(gas side)

(liquid side) 63

• The standard installation of the refnet joint and distributor kit are shown as below:

Outdoor unit

Refnet joint

Indoor unit

Controller

Only connected by the refnet joint

Outdoor unit

Distributor kit

Indoor unit

Controller

Only connected by the distributor kit

Outdoor unit Refnet joint Distributor kit

Controller

Connected by the refnet joint and the distributor kit

64

• Distributor kit should be connected to indoor unit directly; it is not allowed to connect to the distributor kit or refnet joint. Outdoor unit

Distributor kit

Indoor unit

Controller

Leakage Test Refrigerant piping assembly finished

Is the pressure released?

Pressure charging

No

Pass

Yes Check and maintain it

• The pressure charging must be tested in both liquid pipe and gas pipe: 1. Keep 3.0kg/cm2 pressure gas for more than 3 minutes. This is to search for big gap (if any). 2. Keep 15.0kg/cm2 pressure gas for more than 3 minutes. This is to search for smaller gap (if any). 3. Keep 28.0kg/cm2 pressure gas for than 24 hours. Note: Must keep the 28.0kg/cm2 pressure gas for more than 24 hours. The pressure can not be more than 28.0kg/cm2. • Checking procedure:- If the pressure remains the same, then it is OK. - If the pressure decreases, allocate the leak gap and seal it. - If the ambient temperature during the charging is different from the temperature when inspection, the pressure need to be modified as follows: Modified Value = (temp. during charging – temp. during inspection) X 0.1 (i.e. The pressure is charged to 28.0kg/cm2 with ambient temperature at 25°C; after 24hours, the pressure is 27.5kg/cm2 and the ambient temperature is 20°C, then you may conclude as OK)

65

(5) Wiring Electrical Connections • Wiring regulations on wire diameters differ from country to country. Please refer to your LOCAL ELECTRICAL CODES for field wiring rules. Be sure that installations comply with the rules and regulations. General Precautions • Ensure that the rated voltage of the unit corresponds to the name plate before carrying out proper wiring according to the wiring diagram. • Provide a power outlet to be used exclusively for each unit. A power supply disconnects and a circuit breaker for over-current protection should be provided in the exclusive line. • The unit must be GROUNDED to prevent possible hazards due to insulation failures. • All wiring must be firmly connected. • All wiring must not touch the hot refrigerant piping, compressor or any moving parts of fan motors. (6) Vacuuming The pre-charged outdoor unit doest not need any vacuuming or charging. However once it is connected, the system needs to be vacuumed before releasing the R22 from the outdoor unit. 1. Open the service port core cap. 2. Connect pressure gauge to the service port. 3. Connect the line to vacuum pump. Open the charging manifold valve and turn the pump on. Vacuum to -0.1MPa (-760mmHg) or lower. (Evacuation time varies by the pump but averagely in 1 hour). (7) Additional Charge • The refrigerant charge has already charged into the outdoor unit. • The additional amount of the refrigerant depends on the liquid pipe diameter and length. Diameter of the liquid pipe (mm) Amount of the additional refrigerant (g/m)

6.35 50

9.52 80

12.7 120

15.88 180

• The calculation of the additional charging amount is shown as below: Additional Charge = (ø19.05 liquid pipe length x 290) + (ø15.88 liquid pipe length x 180) + ······ + (ø6.35 liquid pipe length x 50)

(7) Overall Checking • Ensure the following, in particular: 1. The unit is mounted solidly and rigid in position. 2. Piping and connections are leak proof after charging. 3. Proper wiring has been done. • Drainage check – pour some water into drain pan. • Test run 1. Conduct a test run after water drainage test and gas leakage test. 2. Watch out for the following: (a) Is the electric plug firmly inserted into the socket? (b) Is there any abnormal sound from the unit? (c) Is there any abnormal vibration with regard to the unit itself or piping? (d) Is there smooth drainage of water? • Check that: 1. Outdoor fan is running, with warm air blowing off the outdoor unit (cooling cycle). 2. Indoor blower is running and discharge cool air (cooling cycle). 3. Suction (low side) pressure is as per recommendations.

66

19.05 290

Sound Data Sound Pressure Level Model MWMD 009G MWMD 010G MWMD 015G MWMD 020G MWMD 025G

Speed High Medium Low High Medium Low High Medium Low High Medium Low High Medium Low

125Hz 32 27 24 28 27 24 30 28 24 37 34 30 41 39 37

1/1 Octave A-weighted Sound Pressure (dBA), ref 20 Pa 250Hz 500Hz 1kHz 2kHz 4kHz 34 38 37 32 23 30 34 32 26 17 27 29 26 20 13 34 37 36 31 22 30 33 31 25 17 26 28 25 19 12 35 39 38 33 25 31 34 33 26 18 26 28 26 20 13 44 42 37 34 25 40 39 34 30 21 35 35 30 26 18 48 47 43 40 32 44 43 39 35 28 41 40 36 32 25

Model

8kHz 15 14 13 13 12 11 15 13 12 15 14 13 23 20 19

Measuring Location

MWMD 009G MWMD 010G MWMD 015G 0.8m

MWMD 020G Microphone

MWMD 025G

1m

Standard : JIS C 9612

67

Overall A (dBA) 40 35 29 39 34 28 42 36 29 43 40 35 49 44 42

Noise Criteria 36 31 24 35 30 23 37 32 24 37 34 30 43 38 35

Sound Pressure Level MCKD-A Series Model

Speed

MCKD 020A MCKD 025A MCKD 030A MCKD 040A MCKD 050A

High Medium Low High Medium Low High Medium Low High Medium Low High Medium Low

125Hz 46 44 43 48 45 43 50 48 46 50 48 46 54 52 51

1/1 Octave A-weighted Sound Pressure (dBA), ref 20µPa 250Hz 500Hz 1kHz 2kHz 4kHz 8kHz 45 40 38 32 21 14 43 37 33 28 18 12 42 35 31 26 17 11 46 43 39 33 27 19 43 40 35 29 21 15 42 38 32 27 19 14 48 47 43 37 35 28 45 43 38 32 31 27 43 41 35 30 30 26 49 49 46 39 38 31 47 47 43 36 34 25 45 46 41 34 30 23 52 51 48 43 42 34 50 50 46 41 40 32 49 49 45 39 39 31

Overall A (dBA) 42 39 37 45 42 40 49 45 43 51 48 46 53 52 50

Noise Criteria 37 32 31 38 35 33 42 38 36 45 42 41 47 45 45

125Hz 43 42 41 45 44 43 46 45 43

1/1 Octave A-weighted Sound Pressure (dBA), ref 20µPa 250Hz 500Hz 1kHz 2kHz 4kHz 8kHz 46 43 40 33 30 20 44 42 39 32 28 19 43 40 37 30 25 17 43 42 39 34 30 19 42 40 38 33 28 17 41 39 36 31 25 16 46 45 42 36 38 26 46 43 41 35 37 23 44 42 39 33 35 20

Overall A (dBA) 44 43 42 44 42 41 47 46 44

Noise Criteria 39 38 36 38 37 35 41 40 38

MCKD-C Series Model

Speed

MCKD 010C MCKD 015C MCKD 020C

High Medium Low High Medium Low High Medium Low

Model

Measuring Location

MCKD 020A MCKD 025A MCKD 010C MCKD 015C MCKD 020C

1.4m Microphone

Standard : JIS C 9612

MCKD 030A MCKD 040A MCKD 050A

1.5m Microphone

Standard : JIS C 8615

68

Sound Pressure Level MCMD-E Series Model

Speed

MCMD 020E

MCMD 025E

MCMD 028E

High Medium Low High Medium Low High Medium Low

1/1 Octave A-weighted Sound Pressure (dBA), ref 20ÂľPa 125Hz 42 36 34 45 43 42 47 44 38

250Hz 46 40 38 47 46 46 50 46 40

500Hz 49 43 41 51 49 47 53 49 43

1kHz 44 37 34 48 46 44 50 46 38

Model

2kHz 43 36 33 47 44 42 50 45 37

4kHz 36 27 23 40 37 35 43 38 28

8kHz 31 20 15 34 31 27 39 33 22

Overall A (dBA)

Noise Criteria

50 43 41 53 51 49 56 51 44

45 38 36 48 45 43 51 46 38

Measuring Location

MCMD 020E MCMD 025E MCMD 028E

0.8m Microphone 1m

Standard : JIS C 9612

69

Sound Pressure Level Model

Speed

MCMD 040D

MCMD 050D

MCMD 062C

1/1 Octave A-weighted Sound Pressure (dBA), ref 20ÂľPa

Overall

Noise

125Hz

250Hz

500Hz

1kHz

2kHz

4kHz

8kHz

A (dBA)

Criteria

High

51

53

51

50

47

37

30

54

49

Medium

48

51

50

49

46

36

28

53

48

Low

46

50

49

48

44

35

27

52

47

High

51

53

51

50

47

37

30

54

49

Medium

48

51

50

49

46

36

28

53

48

Low

46

50

49

48

44

35

27

52

47

High

34

45

49

52

49

44

37

56

51

Medium

32

43

46

49

46

41

33

53

48

Low

26

36

40

42

38

32

24

46

41

Model

Measuring Location

MCMD 040D MCMD 050D 1m

MCMD 062C

Microphone 1m

Standard : JIS C 9612

70

Sound Power Level Model

MCCD 010C

MCCD 015C

MCCD 020C

MCCD 025C

MCCD 030C

MCCD 040C

MCCD 050C

MCCD 060C

Ext. Static (mmAq) 5 4 3 5 4 3 6.5 6 3.5 5.5 4 3 21 17 13 9 21 18 13 9.5 18 16 14 11 18 16 14 10

Speed High Medium Low High Medium Low High Medium Low High Medium Low Super High High Medium Low Super High High Medium Low Super High High Medium Low Super High High Medium Low

1/1 Octave A-weighted Sound Power (dB), ref 1pW 125Hz 250Hz 500Hz 1kHz 2kHz 4kHz 57 54 52 52 51 46 54 51 50 49 48 43 51 48 47 46 44 39 60 58 57 56 54 48 56 55 54 53 50 44 52 50 49 48 44 37 63 62 61 61 59 55 61 61 59 60 58 53 57 56 56 56 53 48 63 52 61 62 59 56 61 60 59 60 57 53 58 57 56 57 54 49 68 69 71 72 69 66 65 66 68 69 65 63 61 62 64 65 61 58 56 58 60 61 57 53 69 71 72 74 71 68 65 68 70 72 68 66 65 65 67 68 64 62 59 61 63 64 60 57 70 71 73 74 72 69 67 69 71 72 69 66 66 66 69 69 66 63 63 64 66 67 62 60 70 71 73 75 73 70 69 70 72 74 71 69 69 68 70 71 67 65 64 65 67 67 63 61

8kHz 44 39 35 44 40 34 51 49 44 53 50 47 65 60 55 49 67 64 59 54 67 64 61 57 68 68 63 59

Overall A (dBA) 57 54 51 61 58 52 65 64 60 66 64 61 76 73 69 64 78 76 72 68 78 76 73 70 79 78 75 71

Duct Discharge Sound Power Level: Test with 5ft length discharge duct, terminated flush with internal wall of reverberation room.

71

Sound Pressure Level Ext. Static (mmAq)

Model MCCD 010C

MCCD 015C

MCCD 020C

MCCD 025C

MCCD 030C

MCCD 040C

MCCD 050C

MCCD 060C

5 4 3 5 4 3 6.5 6 3.5 5.5 4 3 21 17 13 9 21 18 13 9.5 18 16 14 11 18 16 14 10

Speed High Medium Low High Medium Low High Medium Low High Medium Low Super High High Medium Low Super High High Medium Low Super High High Medium Low Super High High Medium Low

1/1 Octave A-weighted Sound Pressure (dBA), ref20ÂľPa 125Hz 33 31 28 39 35 32 42 41 40 42 41 36 54 50 45 42 56 54 49 45 56 54 53 51 57 55 53 51

250Hz 30 28 25 36 34 29 39 37 36 41 40 35 50 45 40 36 49 47 42 39 50 49 47 45 50 49 46 43

500Hz 30 28 24 34 32 28 36 34 32 37 36 33 46 43 40 37 49 47 43 41 50 49 46 44 51 49 47 44

1kHz 29 26 22 32 29 25 34 31 29 34 33 31 45 42 38 33 46 45 41 37 49 48 47 44 51 50 47 43

2kHz 22 20 16 27 23 17 28 26 23 31 29 26 40 37 32 28 41 39 35 30 44 43 40 36 46 44 39 35

4kHz 16 13 10 18 14 11 22 20 18 29 28 27 34 31 26 22 37 35 31 26 38 37 35 32 39 37 34 30

8kHz 10 8 7 11 9 8 17 15 13 23 22 21 30 26 20 15 32 29 24 18 33 32 29 26 35 33 28 24

Overall A (dBA) 33 30 26 37 34 29 38 36 34 40 39 36 49 46 42 38 51 49 45 41 53 52 50 47 55 53 50 47

Microphone position: 1.4m below the centre of the unit. (GB Standard - GB/D17758) Tested with 2m length duct at the air discharge outlet and air return inlet.

Measuring Location:

2m length test duct

2m length test duct

Air

Test Unit

1.4m Microphone

72

Noise Criteria 27 24 20 31 27 23 33 30 27 33 32 30 44 41 37 32 45 44 40 36 48 47 46 43 50 49 46 42

MWMD 009G NC CURVE 70

60

50

NC-50 NC-45

40

NC-40

HI FAN

NC-35

ME FAN

30

NC-30

LO FAN

NC-25 20

NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MWMD 010G NC CURVE 70

60

50

NC-50 NC-45

40

NC-40 NC-35 HI FAN

30

NC-30

ME FAN LO FAN

NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

73

2000

4000

8000

MWMD 015G NC CURVE 70

60

50

NC-50 NC-45

40

NC-40

HI FAN

NC-35 ME FAN

30

NC-30 LO FAN

NC-25

20 NC-20

10

125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MWMD 020G NC CURVE 70

60

50

NC-50 NC-45

40

NC-40 LO FAN

30

ME FAN

HI

NC-35 NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

74

2000

4000

8000

MWMD 025G NC CURVE 70

60

50

NC-50 NC-45

HI FAN 40

NC-40

ME LO FAN FAN

NC-35 30

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MCKD 020A NC CURVE 70

60

50

NC-50 NC-45

40

NC-40

HI FAN

NC-35

ME FAN

30

NC-30

LO FAN

NC-25 20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

75

2000

4000

8000

MCKD 025A NC CURVE 70

60

50

NC-50 NC-45

40

NC-40 HI FAN NC-35

ME FAN

30

NC-30

LO FAN NC-25 20 NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MCKD 030A NC CURVE 70

60

50

NC-50 NC-45

HI FAN 40

NC-40

ME FAN

NC-35

LO FAN

30

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

76

2000

4000

8000

MCKD 040A NC CURVE 70

60

50

NC-50 NC-45 HI FAN

40

NC-40

ME FAN

NC-35 LO FAN

30

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MCKD 050A NC CURVE 70

60

50

NC-50 HI

NC-45 ME FAN

40

NC-40

LO FAN

NC-35 30

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

77

2000

4000

8000

MCKD 010C NC CURVE 70

60

50

NC-50 NC-45

40

NC-40 NC-35 HI FAN

30

NC-30

ME FAN LO FAN

NC-25

20 NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MCKD 015C NC CURVE 70

60

50

NC-50 NC-45

40

NC-40 NC-35

30

HI FAN LO FAN

ME FAN

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

78

2000

4000

8000

MCKD 020C NC CURVE 70

60

50

NC-50 NC-45

40

30

HI

NC-40

ME FAN LO FAN

NC-35 NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MCMD 020E NC CURVE 70

60

50

NC-50 NC-45

40

HI

NC-40 NC-35

ME FAN

30

LO FAN

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

79

2000

4000

8000

MCMD 025E NC CURVE 70

60

50

NC-50

HI FAN

ME

NC-45 LO FAN

40

NC-40 NC-35

30

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MCMD 028E NC CURVE

70

60

50

NC-50 HI FAN NC-45 ME FAN

40 LO FAN

NC-40 NC-35

30

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

80

2000

4000

8000

MCMD 040D NC CURVE 70

60

50

NC-50 HI FAN ME FAN

NC-45 LO FAN

40

NC-40 NC-35

30

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MCMD 050D NC CURVE 70

60

50

NC-50 HI FAN ME FAN LO FAN

40

NC-45 NC-40 NC-35

30

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

81

2000

4000

8000

MCMD 062C NC CURVE 70

60

HI FAN

50

NC-50

ME FAN

NC-45 LO FAN

40

NC-40 NC-35

30

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MCCD 010C NC CURVE 70

60

50

NC-50 NC-45

40

NC-40 NC-35 HI FAN

30

NC-30 ME FAN

NC-25

LO FAN

20

NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

82

2000

4000

8000

MCCD 015C NC CURVE 70

60

50

NC-50 NC-45

40

NC-40 NC-35 HI FAN

30

NC-30

ME FAN

NC-25

LO FAN

20 NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MCCD 020C NC CURVE 70

60

50

NC-50 NC-45

40

NC-40 NC-35

30 ME FAN LO FAN

NC-30

HI FAN

NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

83

2000

4000

8000

MCCD 025C NC CURVE 70

60

50

NC50 NC45

40

NC-40 NC-35 HI FAN

30

NC-30

ME LO FAN FAN

NC25

20

NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MCCD 030C NC CURVE 70

60

50

NC-50 NC-45 SH FAN

40

NC-40

HI FAN

NC-35

ME FAN

30

NC-30 LO FAN NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

84

2000

4000

8000

MCCD 040C NC CURVE 70

60

50

NC-50 NC-45

40

SH FAN

NC-40

HI FAN

NC-35

ME FAN LO FAN

30

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

2000

4000

8000

Octave-band Frequency (Hz)

MCCD 050C NC CURVE 70

60

50

NC-50 SH FAN

NC-45

HI FAN

40

NC-40

ME FAN LO FAN

NC-35

30

NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

85

2000

4000

8000

MCCD 060C NC CURVE

70

60

50

NC-50 SH FAN

NC-45 HI FAN

40

NC-40 ME FAN LO FAN

30

NC-35 NC-30 NC-25

20 NC-20

10

0 125

250

500

1000

Octave-band Frequency (Hz)

86

2000

4000

8000

Selection Process Fan Performance Curves

FAN PERFORMANCE CURVE MCCD 010C 12

10

H M

8

Total Static Pressure , (mm w.g.)

L

1200 RPM 6

1100 RPM 4

1000 RPM 2

INTERNAL STATIC

900 RPM

800 RPM

0 0

50

100

150

200

250

300

Flowrate , (CFM)

87

350

400

450

500

FAN PERFORMANCE CURVE MCCD 015C 14

12

H

Total Static Pressure , (mm w.g.)

10

1300 RPM

M

8

1200 RPM L

6

1100 RPM

4

1000 RPM INTERNAL STATIC

2

800 RPM

700 RP M

900 RPM

0 0

100

200

300

400

500

600

Flowrate , (CFM)

88

700

800

900

1000

FAN PERFORMANCE CURVE MCCD 020C 16

14

H

M

12

Total Static Pressure , (mm w.g.)

L 1400 RPM

10 1300 RPM

8 1200 RPM

1100 RPM

6

1000 RPM

4

900 RPM

2

800 RPM

INTERNAL STATIC

600 RPM

700 RPM

0 0

200

400

600

Flowrate , (CFM)

89

800

1000

1200

FAN PERFORMANCE CURVE MCCD 025C 16

14

H 12

Total Static Pressure , (mm w.g.)

M

10

L

1400 RPM

8

1300 RPM

6

1200 RPM 4

1100 RPM 2

INTERNAL STATIC

800 RPM

900 RPM

1000 RPM

0 0

200

400

600

Flowrate , (CFM)

90

800

1000

1200

FAN PERFORMANCE CURVE MCCD 030C 30

25

SH

1400 RPM

20

Total Static Pressure , (mm w.g.)

H

1300 RPM

1200 RPM

M

15

1100 RPM

L

1000 RPM

10

900 RPM 800 RPM

5

700 RPM

INTERNAL STATIC 0 0

200

400

600

800

Flowrate , (CFM)

91

1000

1200

1400

FAN PERFORMANCE CURVE MCCD 040C 30

25

SH

Total Static Pressure , (mm w.g.)

20

H 1300 RPM

M 15

L 1200 RPM

10

1100 RPM

5 1000 RPM

INTERNAL STATIC 700 RPM

0

0

200

400

600

800

1000

Flowrate , (CFM)

92

1200

1400

800 RPM

1600

900 RPM

1800

FAN PERFORMANCE CURVE MCCD 050C 35

30

SH H

25

Total Static Pressure , (mm w.g.)

M 1400 RPM

L 20

1300 RPM 15

1200 RPM 1100 RPM

10

INTERNAL STATIC 5

0

600

800

1000

1200

Flowrate , (CFM)

93

1400

1600

1800

FAN PERFORMANCE CURVE MCCD 060C 30

25

SH

Total Static Pressure , (mm w.g.)

20

H

M

15

14OO RPM

L

10

1300 RPM 5

INTERNAL STATIC 800 RPM

900 RPM

1000 RPM

1200 RPM

1100 RPM

0 0

500

1000

1500

Flowrate , (CFM)

94

2000

2500

3000

EXV Selection Indoor Mode

Liquid Pipe Diamter (Inch)

MEX Model

MWMD 009G MWMD 010G MWMD 015G MWMD 020G MWMD 025G

1/4 1/4 1/4 1/4 3/8

MEX-15-2SAP-D MEX-15-2SAP-D MEX-15-2SAP-D MEX-18-2SAP-D MEX-18-3SAP-D

MCKD 010C MCKD 015C MCKD 020C

1/4 1/4 1/4

MEX-15-2SAP-C MEX-15-2SAP-C MEX-18-2SAP-C

MCKD 020A MCKD 025A MCKD 030A MCKD 040A MCKD 050A

1/4 3/8 3/8 3/8 3/8

MEX-18-2SAP-C MEX-18-3SAP-C MEX-24-3SAP-C MEX-24-3SAP-C MEX-24-3SAP-C

MCMD 020E MCMD 025E MCMD 028E

1/4 3/8 3/8

MEX-18-2SAP-C MEX-18-3SAP-C MEX-18-3SAP-C

MCMD 040D MCMD 050D MCMD 062C

3/8 3/8 1/2

MEX-24-3SAP-C MEX-24-3SAP-C MEX-24-4SAP-C

MCCD 010C MCCD 015C MCCD 020C MCCD 025C MCCD 030C MCCD 040C MCCD 050C MCCD 060C

1/4 1/4 1/4 3/8 3/8 3/8 3/8 1/2

MEX-15-2SAP-C MEX-15-2SAP-C MEX-18-2SAP-C MEX-18-3SAP-C MEX-24-3SAP-C MEX-24-3SAP-C MEX-24-3SAP-C MEX-24-4SAP-C

95

Engineering & Physical Data Specifications General Data - MWMD-G Series INDOOR UNIT

MODEL NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

MWMD 009G Btu/h

8500

W

2500

Btu/h

9600

W

2800

NOMINAL TOTAL INPUT POWER

W

24

NOMINAL RUNNING CURRENT

A

0.1

V/Ph/Hz

220 - 240 / 1 / 50

POWER SOURCE REFRIGERANT TYPE

R22

REFRIGERANT CONTROL (EXPANSION DEVICE)

EXV

CONTROL

AIR DISCHARGE

AIR FLOW

LCD REMOTE CONTROL

HIGH

l/s / cfm

130 / 275

MEDIUM

l/s / cfm

106 / 225

LOW

l/s / cfm

83 / 175

dBA

40 / 35 / 29

HEIGHT

mm/in

260 / 10.2

WIDTH

mm/in

799 / 31.5

DEPTH

mm/in

198 / 7.8

HEIGHT

mm/in

337 / 13.3

WIDTH

mm/in

857 / 33.7

DEPTH

mm/in

270 / 10.6

SOUND PRESSURE LEVEL (H/M/L) INDOOR UNIT

DOUBLE LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)

OPERATION

UNIT DIMENSION

PACKING DIMENSION UNIT WEIGHT

kg/lb

10 / 22

CONDENSATE DRAIN SIZE

mm/in

15.9 / FLARE VALVE

TYPE PIPE CONNECTION

SIZE

MODEL

LIQUID

mm/in

6.4 /

GAS

mm/in

9.5 / MWMD 010G

MWMD 015G

Btu/h

9600

12300

W

2800

3600

Btu/h

10900

13600 4000

INDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

W

3200

NOMINAL TOTAL INPUT POWER

W

26

29

NOMINAL RUNNING CURRENT

A

0.1

0.1

V/Ph/Hz

POWER SOURCE

220 - 240 / 1 / 50

REFRIGERANT TYPE

R22

REFRIGERANT CONTROL (EXPANSION DEVICE)

EXV

CONTROL

AIR DISCHARGE

AIR FLOW

LCD REMOTE CONTROL

HIGH

l/s / cfm

142 / 300

163 / 345

MEDIUM

l/s / cfm

118 / 250

135 / 285

LOW

l/s / cfm

94 / 200

104 / 220

dBA

39 / 34 / 28

42 / 36 / 29

SOUND PRESSURE LEVEL (H/M/L) INDOOR UNIT

DOUBLE LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)

OPERATION

UNIT DIMENSION

PACKING DIMENSION

HEIGHT

mm/in

260 / 10.2

WIDTH

mm/in

899 / 35.4

DEPTH

mm/in

198 / 7.8

HEIGHT

mm/in

337 / 13.3

WIDTH

mm/in

957 / 37.7

DEPTH

mm/in

270 / 10.6

UNIT WEIGHT

kg/lb

12 / 26

CONDENSATE DRAIN SIZE

mm/in

15.9 / FLARE VALVE

TYPE PIPE CONNECTION

SIZE

LIQUID

mm/in

GAS

mm/in

6.4 / 9.5 /

12.7 /

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS C 9612 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 0.8m BELOW THE UNIT.

96

General Data - MWMD-G Series MWMD 020G

MWMD 025G

Btu/h

19100

22200

W

5600

6500

Btu/h

21500

25200

INDOOR UNIT

MODEL NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

W

6300

7400

NOMINAL TOTAL INPUT POWER

W

47

66

NOMINAL RUNNING CURRENT

A

0.2

V/Ph/Hz

POWER SOURCE

0.3 220 - 240 / 1 / 50

REFRIGERANT TYPE

R22

REFRIGERANT CONTROL (EXPANSION DEVICE)

EXV

CONTROL

AIR DISCHARGE

AIR FLOW

LCD REMOTE CONTROL

HIGH

l/s / cfm

231 / 490

397 / 630

MEDIUM

l/s / cfm

193 / 410

231 / 490

LOW

l/s / cfm

160 / 340

208 / 440

dBA

43 / 40 / 35

49 / 44 / 42

SOUND PRESSURE LEVEL (H/M/L) INDOOR UNIT

DOUBLE LOUVER (UP & DOWN) & GRILLE (LEFT & RIGHT)

OPERATION

UNIT DIMENSION

PACKING DIMENSION

HEIGHT

mm/in

304 / 12.0

WIDTH

mm/in

1062 / 41.8

DEPTH

mm/in

222 / 8.7

HEIGHT

mm/in

378 / 14.9

WIDTH

mm/in

1130 / 44.5

DEPTH

mm/in

292 / 11.5

UNIT WEIGHT

kg/lb

16 / 35

CONDENSATE DRAIN SIZE

mm/in

19.1 / 3/4

TYPE PIPE CONNECTION

SIZE

FLARE VALVE

LIQUID

mm/in

GAS

mm/in

6.4 / 1/4

9.5 / 3/8 15.9 /

5/8

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS C 9612 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 0.8m BELOW THE UNIT.

97

General Data - MCKD-C Series MODEL

MCKD 010C 9600 2800 10900 3200 16 0.2

INDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

INDOOR UNIT

NOMINAL TOTAL INPUT POWER (COOLING) NOMINAL RUNNING CURRENT (HEATING) POWER SOURCE REFRIGERANT TYPE REFRIGERANT CONTROL (EXPANSION DEVICE) AIR DISCHARGE CONTROL OPERATION HIGH AIR FLOW MEDIUM LOW EXTERNAL STATIC PRESSURE (H/M/L) SOUND PRESSURE LEVEL (H/M/L) HEIGHT UNIT DIMENSION WIDTH ( ) - WITH PANEL DEPTH HEIGHT PACKING DIMENSION WIDTH ( ) - PANEL DEPTH UNIT WEIGHT (UNIT + PANEL) CONDENSATE DRAIN SIZE TYPE LIQUID PIPE CONNECTION SIZE GAS MODEL

Btu/h W Btu/h W W A V/Ph/Hz

l/s / CFM l/s / CFM l/s / CFM Pa / in.wg. dBA mm/in mm/in mm/in mm/in mm/in mm/in kg/lb mm/in

220 - 240 / 1 / 50 R22 EXV 4 WAY AUTOMATIC LOUVER (UP & DOWN) WIRELESS OR WIRED MICROCOMPUTER REMOTE CONTROL 189 / 400 194 / 410 184 / 390 184 / 390 175 / 370 170 / 360 0 0 44 / 43 / 42 44 / 42 / 41 250 (295) / 9.8 (11.6) 570 (640) / 22.4 (25.2) 570 (640) / 22.4 (25.2) 317 (127) / 12.5 (5) 630 (700) / 24.8 (27.6) 630 (700) / 24.8 (27.6) 22 + 2 / 49 + 4 23 + 2 / 51 + 4 19.1 / FLARE VALVE

mm/in mm/in

6.4 /

MCKD 020C 19100

Btu/h

NOMINAL HEATING CAPACITY

6.4 / 12.7 /

9.5 /

INDOOR UNIT

NOMINAL COOLING CAPACITY

MCKD 015C 12300 3600 13600 4000 18 0.3

W

5600

Btu/h

21500

W

6300

NOMINAL TOTAL INPUT POWER (COOLING)

W

22

NOMINAL RUNNING CURRENT (HEATING)

A

0.3

V/Ph/Hz

220 - 240 / 1 / 50

POWER SOURCE REFRIGERANT TYPE

R22

REFRIGERANT CONTROL (EXPANSION DEVICE)

EXV

CONTROL

AIR DISCHARGE

AIR FLOW

WIRELESS OR WIRED MICROCOMPUTER REMOTE CONTROL

HIGH

l/s / CFM

212 / 450

MEDIUM

l/s / CFM

203 / 430

l/s / CFM

194 / 410

LOW EXTERNAL STATIC PRESSURE (H/M/L) INDOOR UNIT

4 WAY AUTOMATIC LOUVER (UP & DOWN)

OPERATION

SOUND PRESSURE LEVEL (H/M/L) UNIT DIMENSION ( ) - WITH PANEL PACKING DIMENSION ( ) - PANEL

Pa / in.wg.

0

dBA

47 / 46 / 44

HEIGHT

mm/in

250 (295) / 9.8 (11.6)

WIDTH

mm/in

570 (640) / 22.4 (25.2) 570 (640) / 22.4 (25.2)

DEPTH

mm/in

HEIGHT

mm/in

317 (127) / 12.5 (5)

WIDTH

mm/in

630 (700) / 24.8 (27.6)

DEPTH

mm/in

630 (700) / 24.8 (27.6)

UNIT WEIGHT (UNIT + PANEL)

kg/lb

23 + 2 / 51 + 4

CONDENSATE DRAIN SIZE

mm/in

19.1 / FLARE VALVE

TYPE PIPE CONNECTION

SIZE

LIQUID

mm/in

6.4 /

GAS

mm/in

12.7 /

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS C 9612 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1.4m BELOW FASCIA.

98

General Data - MCKD-A Series MODEL

MCKD 020A 19100 5600 21500 6300 35 0.5

INDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

INDOOR UNIT

NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT POWER SOURCE REFRIGERANT TYPE REFRIGERANT CONTROL (EXPANSION DEVICE) AIR DISCHARGE CONTROL OPERATION HIGH AIR FLOW MEDIUM LOW EXTERNAL STATIC PRESSURE (H/M/L) SOUND PRESSURE LEVEL (H/M/L) HEIGHT UNIT DIMENSION WIDTH ( ) - WITH PANEL DEPTH HEIGHT PACKING DIMENSION WIDTH ( ) - PANEL DEPTH WEIGHT (UNIT + PANEL) CONDENSATE DRAIN SIZE TYPE PIPE CONNECTION LIQUID SIZE GAS MODEL

Btu/h W Btu/h W W A V/Ph/Hz

220 - 240 / 1 / 50 R22 EXV 4 WAY AUTOMATIC LOUVER (UP & DOWN) WIRELESS OR WIRED MICROCOMPUTER REMOTE CONTROL 349 / 740 368 / 780 297 / 630 311 / 660 283 / 600 283 / 600 0 0 42 / 39 / 37 45 / 42 / 40 335 (363) / 13.2 (14.3) 820 (930) / 32.2 (36.6) 820 (930) / 32.2 (36.6) 380 (130) / 15.0 (5.1) 920 (1020) / 36.2 (40.2) 920 (1000) / 32.2 (36.6) 31 + 4 / 68 + 9 32 + 4 / 71 + 9

l/s / CFM l/s / CFM l/s / CFM Pa / in.wg. dBA mm/in mm/in mm/in mm/in mm/in mm/in kg/lb mm/in

19.1 / FLARE VALVE

mm/in mm/in

NOMINAL HEATING CAPACITY

6.4 / 15.9 /

6.4 / 12.7 /

INDOOR UNIT

NOMINAL COOLING CAPACITY

MCKD 025A 22200 6500 25200 7400 45 0.6

MCKD 030A

MCKD 040A

Btu/h

30700

38200

W

9000

11200

Btu/h

34100

42700 12500

W

10000

NOMINAL TOTAL INPUT POWER

W

60

83

NOMINAL RUNNING CURRENT

A

0.7

0.8

POWER SOURCE

220 - 240 / 1 / 50

V/Ph/Hz

REFRIGERANT TYPE

R410A

REFRIGERANT CONTROL (EXPANSION DEVICE) CONTROL

4 WAY AUTOMATIC LOUVER (UP & DOWN)

OPERATION

AIR FLOW

WIRELESS OR WIRED MICROCOMPUTER REMOTE CONTROL

HIGH

l/s / CFM

415 / 880

467 / 990

MEDIUM

l/s / CFM

349 / 740

406 / 860

LOW

l/s / CFM

321 / 680

359 / 760

Pa / in.wg.

0

0

dBA

49 / 45 / 43

51 / 48 / 46

EXTERNAL STATIC PRESSURE (H/M/L) INDOOR UNIT

EXV

AIR DISCHARGE

SOUND PRESSURE LEVEL (H/M/L) UNIT DIMENSION ( ) - WITH PANEL PACKING DIMENSION ( ) - PANEL

HEIGHT

mm/in

335 (363) / 13.2 (14.3)

WIDTH

mm/in

820 (930) / 32.2 (36.6) 820 (930) / 32.2 (36.6)

DEPTH

mm/in

HEIGHT

mm/in

380 (130) / 15.0 (5.1)

WIDTH

mm/in

920 (1020) / 36.2 (40.2)

DEPTH

mm/in

WEIGHT (UNIT + PANEL)

kg/lb

CONDENSATE DRAIN SIZE

mm/in

920 (1000) / 32.2 (36.6) 35 + 4 / 77 + 9

TYPE PIPE CONNECTION

SIZE

38 + 4 / 84 + 9 19.1 / FLARE VALVE

LIQUID

mm/in

9.5 /

GAS

mm/in

15.9 /

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4a) M5CKD020-025A: SOUND PRESSURE LEVEL ARE ACCORDING TO JIS C 9612 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1.4m BELOW FASCIA. 4b) M5CKD030-040A: SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1.5m BELOW FASCIA.

99

General Data - MCKD-A Series MODEL

INDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

MCKD 050A Btu/h

47800

W

14000

Btu/h

54600

W

16000

NOMINAL TOTAL INPUT POWER (COOLING)

W

120

NOMINAL RUNNING CURRENT (HEATING)

A

1.0

V/Ph/Hz

220 - 240 / 1 / 50

POWER SOURCE REFRIGERANT TYPE

R22

REFRIGERANT CONTROL (EXPANSION DEVICE)

EXV

CONTROL

AIR DISCHARGE

AIR FLOW

WIRELESS OR WIRED MICROCOMPUTER REMOTE CONTROL

HIGH

l/s / CFM

491 / 1040

MEDIUM

l/s / CFM

448 / 950

LOW

l/s / CFM

411 / 870

Pa / in.wg.

0

EXTERNAL STATIC PRESSURE (H/M/L)

dBA

53 / 52 / 50

HEIGHT

mm/in

335 (363) / 13.2 (14.3)

SOUND PRESSURE LEVEL (H/M/L) INDOOR UNIT

4 WAY AUTOMATIC LOUVER (UP & DOWN)

OPERATION

UNIT DIMENSION ( ) - WITH PANEL

PACKING DIMENSION ( ) - PANEL

WIDTH

mm/in

820 (930) / 32.2 (36.6)

DEPTH

mm/in

820 (930) / 32.2 (36.6)

HEIGHT

mm/in

380 (130) / 15.0 (5.1)

WIDTH

mm/in

920 (1020) / 36.2 (40.2)

DEPTH

mm/in

920 (1000) / 32.2 (36.6)

WEIGHT (UNIT + PANEL)

kg/lb

40 + 4 / 88 + 9

CONDENSATE DRAIN SIZE

mm/in

19.1 /

TYPE PIPE CONNECTION

SIZE

FLARE VALVE

LIQUID

mm/in

9.5 /

GAS

mm/in

15.9 /

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1.5m BELOW FASCIA.

100

General Data - MCMD-E Series INDOOR UNIT

MODEL

MCMD 020E Btu/h

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

19100

W

5600

Btu/h

21500

W

6300

NOMINAL TOTAL INPUT POWER

W

101

NOMINAL RUNNING CURRENT

A

0.5

V/Ph/Hz

220 - 240 / 1 / 50

POWER SOURCE REFRIGERANT TYPE

R22

REFRIGERANT CONTROL (EXPANSION DEVICE)

EXV

CONTROL

AIR DISCHARGE

AIR FLOW

INDOOR UNIT

AUTOMATIC LOUVER (UP & DOWN)

OPERATION

WIRELESS OR WIRED MICROCOMPUTER REMOTE CONTROL

HIGH

l/s / CFM

245 / 520

MEDIUM

l/s / CFM

217 / 460

LOW

l/s / CFM

192 / 406

EXTERNAL STATIC PRESSURE (H/M/L) SOUND PRESSURE LEVEL (H/M/L) UNIT DIMENSION

PACKING DIMENSION

Pa / in.wg.

0

dBA

50 / 43 / 41

HEIGHT

mm/in

218 / 8.6

WIDTH

mm/in

1080 / 42.5 630 / 24.8

DEPTH

mm/in

HEIGHT

mm/in

297 / 11.7

WIDTH

mm/in

1197 / 47.1

DEPTH

mm/in

740 / 29.1

UNIT WEIGHT

kg/lb

CONDENSATE DRAIN SIZE

mm/in

27 / 60 19.1 / FLARE VALVE

TYPE PIPE CONNECTION

SIZE

MODEL

LIQUID

mm/in

6.4 /

GAS

mm/in

12.7 /

INDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

MCMD 025E

MCMD 028E

Btu/h

22200

27300

W

6500

8000

Btu/h

25200

30700

W

7400

9000

NOMINAL TOTAL INPUT POWER

W

109

150

NOMINAL RUNNING CURRENT

A

0.5

POWER SOURCE

0.8 220 - 240 / 1 / 50

V/Ph/Hz

REFRIGERANT TYPE

R22

REFRIGERANT CONTROL (EXPANSION DEVICE)

EXV

CONTROL

AIR DISCHARGE

AIR FLOW INDOOR UNIT

AUTOMATIC LOUVER (UP & DOWN)

OPERATION

WIRELESS OR WIRED MICROCOMPUTER REMOTE CONTROL

HIGH

l/s / CFM

274 / 580

MEDIUM

l/s / CFM

250 / 530

264 / 560

LOW

l/s / CFM

231 / 490

217 / 460

EXTERNAL STATIC PRESSURE (H/M/L) SOUND PRESSURE LEVEL (H/M/L) UNIT DIMENSION

PACKING DIMENSION

Pa / in.wg.

0

0

dBA

53 / 51 / 49

56 / 51 / 44

HEIGHT

mm/in

218 / 8.6

WIDTH

mm/in

1080 / 42.5 630 / 24.8

DEPTH

mm/in

HEIGHT

mm/in

297 / 11.7

WIDTH

mm/in

1197 / 47.1

DEPTH

mm/in

740 / 29.1

UNIT WEIGHT

kg/lb

CONDENSATE DRAIN SIZE

mm/in

19.1 /

LIQUID

27 / 60

mm/in

6.4 /

GAS

mm/in

SIZE

28 / 62 19.1 / FLARE VALVE

TYPE PIPE CONNECTION

302 / 640

9.5 / 15.9 /

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS C 9612 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 0.8m BELOW THE UNIT.

101

General Data - MCMD-D/C Series MCMD 040D 38200 11200 42700 12500 153 0.7

INDOOR UNIT

MODEL NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

INDOOR UNIT

NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT POWER SOURCE REFRIGERANT TYPE REFRIGERANT CONTROL (EXPANSION DEVICE) AIR DISCHARGE CONTROL OPERATION HIGH AIR FLOW MEDIUM LOW EXTERNAL STATIC PRESSURE (H/M/L) SOUND PRESSURE LEVEL (H/M/L) HEIGHT UNIT DIMENSION WIDTH DEPTH HEIGHT PACKING DIMENSION WIDTH DEPTH UNIT WEIGHT CONDENSATE DRAIN SIZE TYPE LIQUID PIPE CONNECTION SIZE GAS MODEL

Btu/h W Btu/h W W A V/Ph/Hz

MCMD 050D 47800 14000 54600 16000 171 0.8

220 - 240 / 1 / 50 R22 EXV AUTOMATIC LOUVER (UP & DOWN) & MANUAL LOUVER (BOTTOM) WIRELESS REMOTE CONTROL 477 / 1010 491 / 1040 420 / 890 448 / 950 368 / 780 387 / 820 0 0 54 / 53 / 52 54 / 53 / 52 249 / 9.8 1714 / 67.4 670 / 26.3 345 / 13.6 1816 / 71.4 760 / 29.9 70 / 154

l/s / CFM l/s / CFM l/s / CFM mmAq dBA mm/in mm/in mm/in mm/in mm/in mm/in kg/lb mm/in

19.1 / FLARE VALVE

mm/in mm/in

9.5 / 15.9 /

INDOOR UNIT

MCMD 062C Btu/h

56000

W

16400

Btu/h

63100

W

18500

NOMINAL TOTAL INPUT POWER

W

327

NOMINAL RUNNING CURRENT

A

1.4

V/Ph/Hz

220 - 240 / 1 / 50

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

POWER SOURCE REFRIGERANT TYPE

R22

REFRIGERANT CONTROL (EXPANSION DEVICE)

EXV

CONTROL

OPERATION

AIR FLOW

INDOOR UNIT

AUTOMATIC LOUVER (UP & DOWN) & MANUAL LOUVER (BOTTOM)

AIR DISCHARGE

WIRELESS REMOTE CONTROL

HIGH

l/s / CFM

732 / 1550

MEDIUM

l/s / CFM

623 / 1320

LOW

l/s / CFM

472 / 1000

EXTERNAL STATIC PRESSURE (H/M/L) SOUND PRESSURE LEVEL (H/M/L) UNIT DIMENSION

PACKING DIMENSION

mmAq

0

dBA

56 / 53 / 46

HEIGHT

mm/in

285 / 11.2

WIDTH

mm/in

1903 / 74.9 680 / 26.8

DEPTH

mm/in

HEIGHT

mm/in

368 / 14.5

WIDTH

mm/in

1984 / 78.1

DEPTH

mm/in

760 / 29.9

UNIT WEIGHT

kg/lb

85 / 187

CONDENSATE DRAIN SIZE

mm/in

19.1 / FLARE VALVE

TYPE PIPE CONNECTION

SIZE

LIQUID

mm/in

9.5 /

GAS

mm/in

19.1 /

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.

102

General Data - MCCD-C Series MODEL

MCCD 010C

MCCD 015C

Btu/h

9600

12300

W

2800

3600

Btu/h

10900

13600 4000

INDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

W

3200

NOMINAL TOTAL INPUT POWER (COOLING)

W

65

96

NOMINAL RUNNING CURRENT (COOLING)

A

0.3

0.4

V/Ph/Hz

POWER SOURCE

220 - 240 / 1 / 50

REFRIGERANT TYPE

R22

REFRIGERANT CONTROL (EXPANSION DEVICE)

EXV

CONTROL

AIR DISCHARGE

AIR FLOW INDOOR UNIT

DUCTED

OPERATION

WIRED HANDSET

HIGH

l/s / CFM

142 / 300

241 / 510

MEDIUM

l/s / CFM

123 / 260

208 / 440

LOW

l/s / CFM

104 / 220

170 / 360

Pa (in.wg.)

49 / 39 / 29 (0.2 / 0.2 / 0.1)

49 / 39 / 20 (0.2 / 0.2 / 0.1)

EXTERNAL STATIC PRESSURE (H/M/L) SOUND PRESSURE LEVEL (H/M/L)

dBA

33 / 30 / 26

37 / 34 / 29

HEIGHT

mm/in

261 / 10.3

261 / 10.3

WIDTH

mm/in

765 / 30.1

905 / 35.6

DEPTH

mm/in

411 / 16.2

411 / 16.2

HEIGHT

mm/in

376 / 14.8

376 / 14.8

WIDTH

mm/in

951 / 37.4

1091 / 43.0

DEPTH

mm/in

541 / 21.3

541 / 21.3

WEIGHT

kg/lb

17 / 38

CONDENSATE DRAIN SIZE

mm/in

UNIT DIMENSION

PACKING DIMENSION

TYPE PIPE CONNECTION

SIZE

MODEL

21 / 46 19.1 / FLARE VALVE

LIQUID

mm/in

6.4 /

6.4 /

GAS

mm/in

9.5 /

12.7 /

INDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

MCCD 020C

MCCD 025C

Btu/h

19100

22200

W

5600

6500

Btu/h

21500

25200

W

6300

7400

NOMINAL TOTAL INPUT POWER

W

135

152

NOMINAL RUNNING CURRENT

A

0.6

POWER SOURCE

0.7 220 - 240 / 1 / 50

V/Ph/Hz

REFRIGERANT TYPE

R22

REFRIGERANT CONTROL (EXPANSION DEVICE)

EXV

CONTROL

AIR DISCHARGE

AIR FLOW INDOOR UNIT

DUCTED

OPERATION

WIRED HANDSET

HIGH

l/s / CFM

330 / 700

345 / 730

MEDIUM

l/s / CFM

321 / 680

340 / 720

LOW

l/s / CFM

293 / 620

274 / 580

Pa (in.wg.)

64 / 58 / 34 (0.3 / 0.2 / 0.1)

55 / 39 / 29 (0.2 / 0.2 / 0.1) 40 / 39 / 36

EXTERNAL STATIC PRESSURE (H/M/L) SOUND PRESSURE LEVEL (H/M/L) UNIT DIMENSION

dBA

38 / 36 / 34

HEIGHT

mm/in

261 / 10.3

261 / 10.3

WIDTH

mm/in

1065 / 41.9

1200 / 47.2

DEPTH

mm/in

411 / 16.2

411 / 16.2

HEIGHT

mm/in

376 / 14.8

376 / 14.8

WIDTH

mm/in

1251 / 49.3

1386 / 54.6

DEPTH

mm/in

541 / 21.3

541 / 21.3

WEIGHT

kg/lb

22 / 49

CONDENSATE DRAIN SIZE

mm/in

PACKING DIMENSION

TYPE PIPE CONNECTION

SIZE

25 / 55 19.1 / FLARE VALVE

LIQUID

mm/in

6.4 /

6.4 /

GAS

mm/in

12.7 /

15.9 /

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO GB/D17758 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1.4M BELOW THE UNIT (FREE RETURN AND THE DISCHARGE AIR WAS DUCTED TO ADJACENT ROOM).

103

General Data - MCCD-C Series MODEL NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY

Btu/h W Btu/h W W A V/Ph/Hz

l/s / CFM l/s / CFM l/s / CFM l/s / CFM

EXTERNAL STATIC PRESSURE (H/M/L)

Pa (in.wg.)

INDOOR UNIT

NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT POWER SOURCE REFRIGERANT TYPE REFRIGERANT CONTROL (EXPANSION DEVICE) AIR DISCHARGE CONTROL OPERATION SUPER HIGH HIGH AIR FLOW MEDIUM LOW

SOUND PRESSURE LEVEL (H/M/L) HEIGHT UNIT DIMENSION WIDTH DEPTH HEIGHT PACKING DIMENSION WIDTH DEPTH WEIGHT CONDENSATE DRAIN SIZE TYPE PIPE CONNECTION LIQUID SIZE GAS MODEL

NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT POWER SOURCE REFRIGERANT TYPE REFRIGERANT CONTROL (EXPANSION DEVICE) AIR DISCHARGE CONTROL OPERATION SUPER HIGH HIGH AIR FLOW MEDIUM LOW EXTERNAL STATIC PRESSURE (H/M/L) SOUND PRESSURE LEVEL (H/M/L) HEIGHT WIDTH UNIT DIMENSION DEPTH HEIGHT PACKING DIMENSION WIDTH DEPTH WEIGHT CONDENSATE DRAIN SIZE TYPE PIPE CONNECTION LIQUID SIZE GAS

MCCD 040C 38200 11200 42700 12500 510 2.2 220 - 240 / 1 / 50 R22 EXV DUCTED WIRED HANDSET

566 / 1200 486 / 1030 406 / 860 349 / 740 118 / 84 / 63 / 44 (0.5 / 0.3 / 0.3 / 0.2) 49 / 46 / 42 / 38 378 / 14.9 929 / 36.6 541 / 21.3 415 / 16.3 1126 / 44.3 631 / 24.8 39 / 86

dBA mm/in mm/in mm/in mm/in mm/in mm/in kg/lb mm/in

628 / 1330 571 / 1210 491 / 1040 425 / 900 120 / 98 / 74 / 54 (0.5 / 0.4 / 0.3 / 0.2) 51 / 49 / 45 / 41 378 / 14.9 1045 / 41.1 541 / 21.3 415 / 16.3 1245 / 49.0 631 / 24.8 42 / 93 19.1 /

19.1 / FLARE VALVE

mm/in mm/in

9.5 / 15.9 /

INDOOR UNIT

NOMINAL COOLING CAPACITY

INDOOR UNIT

MCCD 030C 30700 9000 34100 10000 460 2.0

INDOOR UNIT

MCCD 050C 47800 14000 54600 16000 515 2.3

Btu/h W Btu/h W W A V/Ph/Hz

MCCD 060C 56000 16400 63100 18500 659 2.9 220 - 240 / 1 / 50 R22 EXV DUCTED WIRED HANDSET

l/s / CFM l/s / CFM l/s / CFM l/s / CFM

675 / 1430 623 / 1320 580 / 1230 533 / 1130 147 / 126 / 109 / 92 (0.6 / 0.5 / 0.4 / 0.4) 54 / 52 / 51 / 50 378 / 14.9 1299 / 51.1 541 / 21.3 415 / 16.3 1497 / 59.0 631 / 24.8 54 / 119

Pa (in.wg.) dBA mm/in mm/in mm/in mm/in mm/in mm/in kg/lb mm/in

812 / 1720 732 / 1550 632 / 1340 552 / 1170 147 / 120 / 90 / 69 (0.6 / 0.5 / 0.4 / 0.3) 54 / 52 / 49 / 46 378 / 14.9 1499 / 59.0 541 / 21.3 415 / 16.3 1701 / 67.0 631 / 24.8 62 / 137 19.1 / FLARE VALVE

mm/in mm/in

9.5 / 15.9 /

9.5 / 19.1 /

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO GB/D17758 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1.4M BELOW THE UNIT (FREE RETURN AND THE DISCHARGE AIR WAS DUCTED TO ADJACENT ROOM).

104

General Data - MDBD-D Series INDOOR UNIT

MODEL NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER POWER SOURCE

MDBD 080

MDBD 100

Btu/h

76400

95500

W

22400

28000

Btu/h

85300

107500

W

25000

31500

W

1700

1480

V/Ph/Hz

220 ~ 240 / 1 / 50

380 ~ 415 / 3 / 50

REFRIGERANT TYPE

R22

REFRIGERANT CONTROL (EXPANSION DEVICE) CONTROL

DUCTED

OPERATION

AIR FLOW INDOOR UNIT

EXV

AIR DISCHARGE

WIRED CONTROL

HIGH

l/s / CFM

1444 / 3058

MEDIUM

l/s / CFM

1250 / 2647

-

LOW

l/s / CFM

1083 / 2294

-

Pa (in.wg.)

100 / 0.40

150 / 0.60

dBA

57

57

HEIGHT

mm/in

420 / 16.5

520 / 20.5

WIDTH

mm/in

1690 / 66.5

1580 / 62.2

DEPTH

1020 / 40.2

EXTERNAL STATIC PRESSURE (HIGH) SOUND PRESSURE LEVEL (HIGH)

UNIT DIMENSION

1750 / 3706

mm/in

879 / 34.6

WEIGHT

kg/lb

100 / 220

150 / 330

CONDENSATE DRAIN SIZE

mm/in

25.4 / 1.0

25.4 / 1.0

mm/in

12.7 / 1/2

12.7 / 1/2

mm/in

11/8

28.6 / 11/8

TYPE PIPE CONNECTION

SIZE

FLARE VALVE LIQUID GAS

28.6 /

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO GB/D17758 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1.4M BELOW THE UNIT (FREE RETURN AND THE DISCHARGE AIR WAS DUCTED TO ADJACENT ROOM).

105

General Data - Cooling Only MDS 030A

MDS 040A

Btu/h

29,002

34,120

W

8,500

10,000

NOMINAL TOTAL INPUT POWER

W

3,000

3,500

NOMINAL RUNNING CURRENT

A

13.6

15.9

V/Ph/Hz

220 - 240 / 1 / 50

220 - 240 / 1 / 50

MODEL

OUTDOOR UNIT

NOMINAL COOLING CAPACITY

POWER SOURCE REFRIGERANT TYPE

AIR FLOW

l/s / cfm

1056 / 2237

1444 / 3060

MEDIUM

l/s / cfm

944 / 2001

1222 / 2590

LOW

l/s / cfm

778 / 1648

1000 / 2118

dB(A)

59

59

mm/in

900 / 35.4

1044 / 41.4 1058 / 41.7

OUTDOOR UNIT

HEIGHT

PACKING DIMENSION

WIDTH

mm/in

840 / 33.1

DEPTH

mm/in

408 / 16.1

430 / 16.9

HEIGHT

mm/in

1103 / 43.3

1177 / 46.3

WIDTH

mm/in

1027 / 40.4

1225 / 48.2

DEPTH

mm/in

499 / 19.6

506 / 19.9

kg/lb

82 / 181

112 / 247

UNIT WEIGHT TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

9.52 / 3/8

9.52 / 3/8

GAS

mm/in

15.88 / 5/8

19.05 / 3/4

kg/lb

2.2 / 10.2

4.7 / 10.4

MDS 050A

MDS 050A

Btu/h

42,650

42,650

W

12,500

12,500

W

4,400

4,300

NOMINAL COOLING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT POWER SOURCE

A

20.0

8.0

V/Ph/Hz

220-240 / 1 / 50

380-415 / 3 / 50

R22

R22

REFRIGERANT TYPE HIGH

l/s / cfm

1444 / 3060

1444 / 3060

MEDIUM

l/s / cfm

1222 / 2590

1222 / 2590

LOW

l/s / cfm

1000 / 2118

1000 / 2118

dB(A)

59

59

OUTDOOR UNIT

SOUND PRESSURE LEVEL

UNIT DIMENSION

PACKING DIMENSION

HEIGHT

mm/in

1044 / 41.4

1044 / 41.4

WIDTH

mm/in

1058 / 41.7

1058 / 41.7

DEPTH

mm/in

430 / 16.9

430 / 16.9

HEIGHT

mm/in

1177 / 46.3

1177 / 46.3

WIDTH

mm/in

1225 / 48.2

1225 / 48.2

DEPTH

mm/in

506 / 19.9

506 / 19.9

kg/lb

117 / 258

117 / 258

FLARE

FLARE

LIQUID

mm/in

9.52 / 3/8

9.52 / 3/8

GAS

mm/in

19.05 / 3/4

19.05 / 3/4

kg/lb

4.7 / 10.4

4.9 / 10.8

UNIT WEIGHT TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

REFRIGERANT CHARGE

FLARE

mm/in

OUTDOOR UNIT

AIR FLOW

FLARE

LIQUID

REFRIGERANT CHARGE

MODEL

R22

HIGH

SOUND PRESSURE LEVEL

UNIT DIMENSION

R22

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27째C DB / 19째C WB INDOOR AND 35째C DB / 24째C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8616 STANDARD. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

106

General Data - Cooling Only MODEL

OUTDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL TOTAL INPUT POWER

MDS 060A

MDS 060A

Btu/h

49,474

51,180

W

14,500

15,000

W

5,000

5,000

NOMINAL RUNNING CURRENT

A

22.8

9.6

V/Ph/Hz

220-240 / 1 / 50

380-415 / 3 / 50

R22

R22

HIGH

l/s / cfm

2112 / 4474

2112 / 4474

MEDIUM

l/s / cfm

1888 / 4002

1888 / 4002

LOW

l/s / cfm

1556 / 3296

1556 / 3296

dB(A)

60

60

HEIGHT

mm/in

1247 / 49.1

1247 / 49.1

WIDTH

mm/in

1058 / 41.7

1058 / 41.7

DEPTH

mm/in

430 / 16.9

430 / 16.9

HEIGHT

mm/in

1428 / 56.2

1428 / 56.2

WIDTH

mm/in

1177 / 46.3

1177 / 46.3

DEPTH

mm/in

506 / 19.9

506 / 19.9

kg/lb

123 / 271

123 / 271

POWER SOURCE REFRIGERANT TYPE

AIR FLOW

OUTDOOR UNIT

SOUND PRESSURE LEVEL

UNIT DIMENSION

PACKING DIMENSION UNIT WEIGHT

TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

FLARE

FLARE

LIQUID

mm/in

9.52 / 3/8

9.52 / 3/8

GAS

mm/in

19.05 / 3/4

19.05 / 3/4

kg/lb

5.0 / 11.0

5.0 / 11.0

REFRIGERANT CHARGE

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

MODEL

MDS 070A

OUTDOOR UNIT Btu/h

61400

W

18000

NOMINAL TOTAL INPUT POWER

W

6200

NOMINAL RUNNING CURRENT

A

11.5

V/Ph/Hz

380-415 / 3 / 50

l/s / cfm

2225 / 4694

NOMINAL COOLING CAPACITY

POWER SOURCE

R22

REFRIGERANT TYPE HI AIR FLOW

DIUM

l/s / cfm

1998 / 4215

LOW

l/s / cfm

1604 / 3385

dB(A)

62

mm/in

1445 / 56.9

WIDTH

mm/in

1058 / 41.6

DEPTH

mm/in

430 / 16.9

HEIGHT

mm/in

1626 / 64.0

WIDTH

mm/in

1177 / 46.3

DEPTH

mm/in

506 / 19.9

kg/lb

135 / 298

SOUND PRESSURE LEVEL

OUTDOOR UNIT

HEIGHT UNIT DIMENSION

PACKING DIMENSION UNIT WEIGHT

TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

REFRIGERANT CHARGE

FLARE

LIQUID

mm/in

GAS

mm/in

19.1 /

kg/lb

6.5 / 14.3

9.5 /

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. AND 1.42m ABOVE THE MACHINE BASE. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

107

General Data - Cooling Only MODEL

OUTDOOR UNIT

NOMINAL COOLING CAPACITY

MDS 080B

MDS 100B

Btu/h

83,594

95,536

W

24,500

28,000

NOMINAL TOTAL INPUT POWER

W

7,500

8,500

NOMINAL RUNNING CURRENT

A

14.6

16.8

V/Ph/Hz

380-415 / 3 / 50

380-415 / 3 / 50

R22

R22

HI-FAN

l/s / cfm

3194 / 6768

3194 / 6768

LOW-FAN

l/s / cfm

1528 / 3237

1528 / 3237

dB(A)

62

64

mm/in

1840 / 72.4

1840 / 72.4

WIDTH

mm/in

990 / 39.0

990 / 39.0

DEPTH

mm/in

840 / 33.0

840 / 33.0

HEIGHT

mm/in

2010 / 79.1

2010 / 79.1

WIDTH

mm/in

1030 / 40.6

1030 / 40.6

DEPTH

mm/in

890 / 35.0

890 / 35.0

kg/lb

275 / 606

385 / 628

Flare / Brazed

Flare / Brazed

POWER SOURCE REFRIGERANT TYPE AIR FLOW SOUND PRESSURE LEVEL

OUTDOOR UNIT

HEIGHT UNIT DIMENSION

PACKING DIMENSION UNIT WEIGHT

TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

LIQUID

mm/in

12.7 / 1/2

12.7 / 1/2

GAS

mm/in

28.6 / 1 1/8

28.6 / 1 1/8

kg/lb

8 / 17.6

10 / 22.0

REFRIGERANT CHARGE

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

MODEL

MDS 120B

MDS 150B

Btu/h

110,890

136,480

W

32,500

40,000

W

9,800

12,900

OUTDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL TOTAL INPUT POWER

A

18.8

23.1

V/Ph/Hz

380-415 / 3 / 50

380-415 / 3 / 50

R22

R22

HI-FAN

l/s / cfm

3472 / 7357

3750 / 7945

LOW-FAN

l/s / cfm

2083 / 4414

2222 / 4708

dB(A)

66

67

HEIGHT

mm/in

1840 / 72.4

1840 / 72.4

WIDTH

mm/in

990 / 39.0

1290 / 50.8

DEPTH

mm/in

840 / 33.0

840 / 33.0

HEIGHT

mm/in

2010 / 79.1

2010 / 79.1

WIDTH

mm/in

1030 / 40.6

1330 / 52.4

DEPTH

mm/in

890 / 35.0

890 / 35.0

kg/lb

290 / 639

355 / 783

Flare / Brazed

Flare / Brazed

NOMINAL RUNNING CURRENT POWER SOURCE REFRIGERANT TYPE AIR FLOW

OUTDOOR UNIT

SOUND PRESSURE LEVEL

UNIT DIMENSION

PACKING DIMENSION

UNIT WEIGHT TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

REFRIGERANT CHARGE

LIQUID

mm/in

15.88 / 5/8

15.88 / 5/8

GAS

mm/in

28.6 / 1 1/8

34.9 / 1 3/8

kg/lb

12 / 26.5

15 / 33

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

108

General Data - Cooling Only MDS 180B

MDS 200B

Btu/h

162,070

170,600

W

47,500

50,000

NOMINAL TOTAL INPUT POWER

W

14,100

15,200

NOMINAL RUNNING CURRENT

A

28.2

31.1

V/Ph/Hz

380-415 / 3 / 50

380-415 / 3 / 50

R22

R22

HI-FAN

l/s / cfm

3194+3194 / 6768+6768

3194+3194 / 6768+6768

LOW-FAN

l/s / cfm

1528+1528 / 3237+3237

1528+1528 / 3237+3237

dB(A)

66

66

mm/in

1840 / 72.4

1840 / 72.4 1990 / 78.3

MODEL

OUTDOOR UNIT

NOMINAL COOLING CAPACITY

POWER SOURCE REFRIGERANT TYPE AIR FLOW SOUND PRESSURE LEVEL

OUTDOOR UNIT

HEIGHT UNIT DIMENSION

PACKING DIMENSION

WIDTH

mm/in

1990 / 78.3

DEPTH

mm/in

840 / 33.0

840 / 33.0

HEIGHT

mm/in

2010 / 79.1

2010 / 79.1

WIDTH

mm/in

2010 / 79.1

2010 / 79.1

DEPTH

mm/in

890 / 35.0

890 / 35.0

kg/lb

520 / 1146

560 / 1235

Flare / Brazed

Flare / Brazed

UNIT WEIGHT TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

LIQUID

mm/in

15.88 / 5/8

15.88 / 5/8

GAS

mm/in

34.9 / 1 3/8

34.9 / 1 3/8

kg/lb

21 / 46.3

22 / 48.5

REFRIGERANT CHARGE

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

MODEL

MDS 220B

MDS 240B

Btu/h

187,660

221,780

OUTDOOR UNIT

NOMINAL COOLING CAPACITY

W

55,000

65,000

NOMINAL TOTAL INPUT POWER

W

16,700

19,800

NOMINAL RUNNING CURRENT

A

32.7

38.5

V/Ph/Hz

380-415 / 3 / 50

380-415 / 3 / 50

R22

R22

POWER SOURCE REFRIGERANT TYPE AIR FLOW

HI-FAN

l/s / cfm

3194+3194 / 6768+6768

3472+3472 / 7357+7357

LOW-FAN

l/s / cfm

1528+1528 / 3237+3237

2083+2083 / 4414+4414

OUTDOOR UNIT

SOUND PRESSURE LEVEL

UNIT DIMENSION

PACKING DIMENSION

dB(A)

66

68

HEIGHT

mm/in

1840 / 72.4

1840 / 72.4

WIDTH

mm/in

1990 / 78.3

1990 / 78.3

DEPTH

mm/in

840 / 33.0

840 / 33.0

HEIGHT

mm/in

2010 / 79.1

2010 / 79.1

WIDTH

mm/in

2010 / 79.1

2010 / 79.1

DEPTH

mm/in

890 / 35.0

890 / 35.0

kg/lb

560 / 1235

570 / 1257

Flare / Brazed

Flare / Brazed

UNIT WEIGHT TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

REFRIGERANT CHARGE

LIQUID

mm/in

19.05 / 3/4

19.05 / 3/4

GAS

mm/in

38.1 / 1 1/2

38.1 / 1 1/2

kg/lb

22 / 48.5

24 / 52.9

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

109

General Data - Cooling Only MDS 260B

MDS 280B

MDS 120BM + MDS 150BS

MDS 150BM + MDS 130BS

Btu/h

238,840

255,900

W

70,000

75,000

NOMINAL TOTAL INPUT POWER

W

21,300

22,800

NOMINAL RUNNING CURRENT

A

40.0

42.5

V/Ph/Hz

380-415 / 3 / 50

380-415 / 3 / 50

R22

R22

HI-FAN

l/s / cfm

3472 + 3750 / 7357 + 7945

3750 + 3750 / 7945 + 7945

LOW-FAN

l/s / cfm

2083 + 2222 / 4414 + 4708

2222 + 2222 / 4708 + 4708

dB(A)

68

69

mm/in

1840 / 72.4

1840 / 72.4 2590 / 102.0

OUTDOOR UNIT

MODEL

MASTER UNIT+SLAVE UNIT

NOMINAL COOLING CAPACITY

POWER SOURCE REFRIGERANT TYPE AIR FLOW SOUND PRESSURE LEVEL HEIGHT OUTDOOR UNIT

UNIT DIMENSION

PACKING DIMENSION

WIDTH

mm/in

2290 / 90.2

DEPTH

mm/in

840 / 33.0

840 / 33.0

HEIGHT

mm/in

2010 + 2101 / 79.1 + 79.1

2010 +2010 / 79.1 + 79.1

WIDTH

mm/in

1030 + 1330 / 40.6 + 52.4

1330 + 1330 / 52.4 + 52.4

DEPTH

mm/in

890 + 890 / 35.0 + 35.0

890 + 890 / 35.0 + 35.0

kg/lb

645 / 1422

710 / 1565

Flare / Brazed

Flare / Brazed

UNIT WEIGHT TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

LIQUID

mm/in

19.05 / 3/4

19.05 / 3/4

GAS

mm/in

41.3 / 1 5/8

41.3 / 1 5/8

kg/lb

27 / 59.5

30 / 66.1

REFRIGERANT CHARGE

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

OUTDOOR UNIT

MDS 300B

MDS 320B

MDS 150BM + MDS 150BS

MDS 160BM + MDS 160BS

Btu/h

272,960

290,020

W

80,000

85,000

NOMINAL TOTAL INPUT POWER

W

26,200

27,700

NOMINAL RUNNING CURRENT

A

46.5

49.5

V/Ph/Hz

380-415 / 3 / 50

380-415 / 3 / 50

R22

R22

HI-FAN

l/s / cfm

3750 + 3750 / 7945 + 7945

3750 + 3750 / 7945 + 7945

LOW-FAN

l/s / cfm

2222 + 2222 / 4708 + 4708

2222 + 2222 / 4708 + 4708

dB(A)

69

69

mm/in

1840 / 72.4

1840 / 72.4 2590 / 102.0

MODEL

MASTER UNIT+SLAVE UNIT

NOMINAL COOLING CAPACITY

POWER SOURCE REFRIGERANT TYPE AIR FLOW SOUND PRESSURE LEVEL HEIGHT OUTDOOR UNIT

UNIT DIMENSION

PACKING DIMENSION

WIDTH

mm/in

2590 / 102.0

DEPTH

mm/in

840 / 33.0

840 / 33.0

HEIGHT

mm/in

2010 + 2101 / 79.1 + 79.1

2010 +2010 / 79.1 + 79.1

WIDTH

mm/in

1030 + 1330 / 40.6 + 52.4

1330 + 1330 / 52.4 + 52.4

DEPTH

mm/in

890 + 890 / 35.0 + 35.0

890 + 890 / 35.0 + 35.0

kg/lb

710 / 1565

720 / 1587

Flare / Brazed

Flare / Brazed

UNIT WEIGHT TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

REFRIGERANT CHARGE

LIQUID

mm/in

19.05 / 3/4

19.05 / 3/4

GAS

mm/in

41.3 / 1 5/8

41.3 / 1 5/8

kg/lb

30 / 66.1

30 / 66.1

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

110

General Data - Heat pump MODEL

OUTDOOR UNIT

MDS 030AR

MDS 040AR

Btu/h

29,002

34,120

W

8,500

10,000

Btu/h

30,708

39,238

W

9,000

11,500

COOLING

W

3,000

3,500

HEATING

W

2,500

3,400

COOLING

A

13.6

15.9

HEATING

A

11.4

15.5

V/Ph/Hz

220-240 / 1 / 50

220-240 / 1 / 50

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT POWER SOURCE REFRIGERANT TYPE

R22

HIGH

l/s / cfm

1056 / 2237

1444 / 3060

MEDIUM

l/s / cfm

944 / 2001

1222 / 2590

LOW

l/s / cfm

778 / 1648

1000 / 2118

UNIT WEIGHT

dB(A) mm/in mm/in mm/in mm/in mm/in mm/in kg/lb

TYPE (LIQUID/GAS) LIQUID SIZE GAS REFRIGERANT CHARGE

mm/in mm/in kg/lb

59 900 / 35.4 840 / 33.1 408 / 16.1 1103 / 43.3 1027 / 40.4 499 / 19.6 85 / 187 FLARE 9.52 / 3/8 15.88 / 5/8 2.7 / 5.95

59 1044 / 41.4 1058 / 41.7 430 / 16.9 1177 / 46.3 1225 / 48.2 506 / 19.9 115 / 254 FLARE 9.52 / 3/8 19.05 / 3/4 4.0 / 8.80

AIR FLOW SOUND PRESSURE LEVEL OUTDOOR UNIT

R22

UNIT DIMENSION

PACKING DIMENSION

HEIGHT WIDTH DEPTH HEIGHT WIDTH DEPTH

PIPE CONNECTION

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

MODEL

MDS 050AR

MDS 050AR

Btu/h

42,650

42,650

W

12,500

12,500

Btu/h

46,062

46,062

OUTDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT

W

13,500

13,500

COOLING

W

4,400

4,300

HEATING

W

4,200

3,900

COOLING

A

20.0

8.0

HEATING

A

19.0

7.3

V/Ph/Hz

220-240 / 1 / 50

380-415 / 3 / 50

R22

R22

l/s / cfm

1444 / 3060

1444 / 3060

MEDIUM

l/s / cfm

1222 / 2590

1222 / 2590

LOW

l/s / cfm

1000 / 2118

1000 / 2118

dB(A) mm/in mm/in

59 1044 / 41.4 1058 / 41.7

59 1044 / 41.4 1058 / 41.7

POWER SOURCE REFRIGERANT TYPE HIGH AIR FLOW

OUTDOOR UNIT

SOUND PRESSURE LEVEL UNIT DIMENSION

HEIGHT WIDTH DEPTH

mm/in

430 / 16.9

430 / 16.9

HEIGHT WIDTH DEPTH

UNIT WEIGHT

mm/in mm/in mm/in kg/lb

1177 / 46.3 1225 / 48.2 506 / 19.9 120 / 265

1177 / 46.3 1225 / 48.2 506 / 19.9 120 / 265

TYPE (LIQUID/GAS) LIQUID SIZE GAS REFRIGERANT CHARGE

mm/in mm/in kg/lb

FLARE 9.52 / 3/8 19.05 / 3/4 4.3 / 9.50

FLARE 9.52 / 3/8 19.05 / 3/4 4.9 / 10.8

PACKING DIMENSION

PIPE CONNECTION

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

111

General Data - Heat pump MODEL

MDS 060AR

OUTDOOR UNIT

49,474

51,180

W

14,500

15,000

Btu/h

56,298

58,004

W

16,500

17,000

COOLING

W

5,000

5,000

HEATING

W

4,200

4,230

COOLING

A

22.8

9.6

HEATING

A

20.3

8.8

V/Ph/Hz

220-240 / 1 / 50

380-415 / 3 / 50

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT POWER SOURCE REFRIGERANT TYPE HIGH AIR FLOW

OUTDOOR UNIT

R22

2112 / 4474

2112 / 4474

MEDIUM

l/s / cfm

1888 / 4002

1888 / 4002

l/s / cfm dB(A) mm/in mm/in mm/in mm/in mm/in mm/in kg/lb

1556 / 3296 60 1247 / 49.1 1058 / 41.7 430 / 16.9 1428 / 56.2 1177 / 46.3 506 / 19.9 130 / 287 FLARE 9.52 / 3/8 19.05 / 3/4 5.0 / 11.0

1556 / 3296 60 1247 / 49.1 1058 / 41.7 430 / 16.9 1428 / 56.2 1177 / 46.3 506 / 19.9 130 / 287 FLARE 9.52 / 3/8 19.05 / 3/4 5.0 / 11.0

HEIGHT WIDTH DEPTH HEIGHT WIDTH DEPTH

PACKING DIMENSION

l/s / cfm

R22

LOW SOUND PRESSURE LEVEL UNIT DIMENSION

MDS 060AR

Btu/h

UNIT WEIGHT TYPE (LIQUID/GAS) LIQUID SIZE GAS REFRIGERANT CHARGE PIPE CONNECTION

mm/in mm/in kg/lb

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

MODEL

OUTDOOR UNIT

61,400

W

18,000

Btu/h

68,200

W

20,000

COOLING

W

6,200

HEATING

W

6,000

COOLING

A

12

HEATING

A

11

V/Ph/Hz

380-415 / 3 / 50

l/s / cfm

2225 / 4694

DIUM

l/s / cfm

1998 / 4215

LOW

l/s / cfm

1604 / 3385

NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT

MDS 070AR Btu/h

NOMINAL COOLING CAPACITY

POWER SOURCE

R22

REFRIGERANT TYPE HI AIR FLOW

OUTDOOR UNIT

SOUND PRESSURE LEVEL

dB(A)

62

mm/in

1445 / 56.9

WIDTH

mm/in

1058 / 41.6

DEPTH

mm/in

430 / 16.9

HEIGHT

mm/in

1626 / 64.0

WIDTH DEPTH

mm/in mm/in kg/lb

1177 / 46.3 506 / 19.9 140 / 309

HEIGHT UNIT DIMENSION

PACKING DIMENSION UNIT WEIGHT

TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

REFRIGERANT CHARGE

FLARE

LIQUID

mm/in

GAS

mm/in

9.5 / 19.1 / 6.5 / 14.3

kg/lb

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

112

General Data - Heat pump MODEL

OUTDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT

MDS 080BR

MDS 100BR

Btu/h

83,594

95,536

W

24,500

28,000

Btu/h

88,712

102,360

W

26,000

30,000

COOLING

W

7,500

8,500

HEATING

W

7,200

8,300

COOLING

A

14.6

16.8

HEATING

A

13.6

15.7

V/Ph/Hz

380-415 / 3 / 50

380-415 / 3 / 50

POWER SOURCE REFRIGERANT TYPE AIR FLOW

OUTDOOR UNIT

PACKING DIMENSION

l/s / cfm

3194 / 6768

3194 / 6768

LOW-FAN

l/s / cfm

1528 / 3237

1528 / 3237

dB(A)

62

64

HEIGHT

mm/in

1840 / 72.4

1840 / 72.4

WIDTH

mm/in

990 / 39.0

990 / 39.0

DEPTH

mm/in

840 / 33.0

840 / 33.0

HEIGHT

mm/in

2010 / 79.1

2010 / 79.1

WIDTH

mm/in

1030 / 40.6

1030 / 40.6

DEPTH

mm/in

890 / 35.0

890 / 35.0

kg/lb

290 / 640

300 / 660

Flare / Brazed

Flare / Brazed

UNIT WEIGHT TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

R22

HI-FAN

SOUND PRESSURE LEVEL UNIT DIMENSION

R22

LIQUID

mm/in

12.7 / 1/2

12.7 / 1/2

GAS

mm/in

28.6 / 1 1/8

28.6 / 1 1/8

kg/lb

8 / 17.6

10 / 22.0

REFRIGERANT CHARGE

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

MODEL

MDS 120BR

MDS 150BR

Btu/h

110,890

136,480

W

32,500

40,000

Btu/h

116,008

146,716

OUTDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT

W

34,000

43,000

COOLING

W

9,800

12,900

HEATING

W

9,000

11,100

COOLING

A

18.8

23.1

HEATING

A

16.7

22.6

V/Ph/Hz

380-415 / 3 / 50

380-415 / 3 / 50

R22

R22

HI-FAN

l/s / cfm

3472 / 7357

3750 / 7945

LOW-FAN

l/s / cfm

2083 / 4414

2222 / 4708

dB(A) mm/in mm/in

66 1840 / 72.4 990 / 39.0

67 1840 / 72.4 1290 / 50.8

POWER SOURCE REFRIGERANT TYPE AIR FLOW

OUTDOOR UNIT

SOUND PRESSURE LEVEL UNIT DIMENSION

HEIGHT WIDTH DEPTH

mm/in

840 / 33.0

840 / 33.0

HEIGHT WIDTH DEPTH

UNIT WEIGHT

mm/in mm/in mm/in kg/lb

TYPE (LIQUID/GAS) LIQUID SIZE GAS REFRIGERANT CHARGE

mm/in mm/in kg/lb

2010 / 79.1 1030 / 40.6 890 / 35.0 305 / 672 Flare / Brazed 15.88 / 5/8 28.6 / 1 1/8 12 / 26.5

2010 / 79.1 1330 / 52.4 890 / 35.0 370 / 816 Flare / Brazed 15.88 / 5/8 34.9 / 1 3/8 15 / 33

PACKING DIMENSION

PIPE CONNECTION

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

113

General Data - Heat pump MODEL

OUTDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT

MDS 180BR

MDS 200BR

Btu/h

162,070

170,600

W

47,500

50,000

Btu/h

170,600

180,836 53,000

W

50,000

COOLING

W

14,100

15,200

HEATING

W

13,200

14,700

COOLING

A

28.2

31.1

HEATING

A

27.1

29.4

V/Ph/Hz

380-415 / 3 / 50

380-415 / 3 / 50

R22

R22

HI-FAN

l/s / cfm

3194+3194 / 6768+6768

3194+3194 / 6768+6768

LOW-FAN

l/s / cfm

1528+1528 / 3237+3237

1528+1528 / 3237+3237

dB(A)

66

66

mm/in

1840 / 72.4

1840 / 72.4 1990 / 78.3

POWER SOURCE REFRIGERANT TYPE AIR FLOW SOUND PRESSURE LEVEL OUTDOOR UNIT

HEIGHT UNIT DIMENSION

PACKING DIMENSION

WIDTH

mm/in

1990 / 78.3

DEPTH

mm/in

840 / 33.0

840 / 33.0

HEIGHT

mm/in

2010 / 79.1

2010 / 79.1

WIDTH

mm/in

2010 / 79.1

2010 / 79.1

DEPTH

mm/in

890 / 35.0

890 / 35.0

kg/lb

550 / 1213

590 / 1301

Flare / Brazed

Flare / Brazed

UNIT WEIGHT TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

LIQUID

mm/in

15.88 / 5/8

15.88 / 5/8

GAS

mm/in

34.9 / 1 3/8

34.9 / 1 3/8

kg/lb

21 / 46.3

22 / 48.5

REFRIGERANT CHARGE

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

MODEL

OUTDOOR UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT

MDS 220BR

MDS 240BR

Btu/h

187,660

221,780

W

55,000

65,000

Btu/h

197,896

232,016

W

58,000

68,000

COOLING

W

16,700

19,800 18,500

HEATING

W

16,200

COOLING

A

32.7

38.5

HEATING

A

31.0

33.8

V/Ph/Hz

380-415 / 3 / 50

380-415 / 3 / 50

POWER SOURCE REFRIGERANT TYPE AIR FLOW

OUTDOOR UNIT

R22

HI-FAN

l/s / cfm

3194+3194 / 6768+6768

3472+3472 / 7357+7357

LOW-FAN

l/s / cfm

1528+1528 / 3237+3237

2083+2083 / 4414+4414

dB(A) mm/in mm/in

66 1840 / 72.4 1990 / 78.3

68 1840 / 72.4 1990 / 78.3

SOUND PRESSURE LEVEL UNIT DIMENSION

R22

HEIGHT WIDTH DEPTH

mm/in

840 / 33.0

840 / 33.0

HEIGHT WIDTH DEPTH

UNIT WEIGHT

mm/in mm/in mm/in kg/lb

TYPE (LIQUID/GAS) LIQUID SIZE GAS REFRIGERANT CHARGE

mm/in mm/in kg/lb

2010 / 79.1 2010 / 79.1 890 / 35.0 590 / 1301 Flare / Brazed 19.05 / 3/4 38.1 / 1 1/2 22 / 48.5

2010 / 79.1 2010 / 79.1 890 / 35.0 600 / 1323 Flare / Brazed 19.05 / 0.75 38.1 / 1.5 24 / 52.9

PACKING DIMENSION

PIPE CONNECTION

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

114

General Data - Heat pump MODEL

MDS 260BR

MDS 280BR

MDS 120BRM + MDS 150BRS

MDS 150BRM + MDS 130BRS

Btu/h

238,840

255,900

W

70,000

75,000

Btu/h

255,900

272,960

OUTDOOR UNIT MASTER UNIT+SLAVE UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT

W

75,000

80,000

COOLING

W

21,300

22,800

HEATING

W

20,900

22,000

COOLING

A

40.0

42.5

HEATING

A

37.2

41.0

V/Ph/Hz

380-415 / 3 / 50

380-415 / 3 / 50

R22

R22

HI-FAN

l/s / cfm

3472 + 3750/7357 + 7945

3750 + 3750/7945 + 7945

LOW-FAN

l/s / cfm

2083 + 2222/4414 + 4708

2222 + 2222/4708 + 4708

dB(A)

68

69

HEIGHT

mm/in

1840/72.4

1840/72.4

WIDTH

mm/in

2290/90.2

2590/102.0

DEPTH

mm/in

840/33.0

840/33.0

HEIGHT

mm/in

2010 + 2101 / 79.1 + 79.1

2010 +2010 / 79.1 + 79.1

WIDTH

mm/in

1030 + 1330 / 40.6 + 52.4

1330 + 1330 / 52.4 + 52.4

DEPTH

mm/in

890 + 890 / 35.0 + 35.0

890 + 890 / 35.0 + 35.0

kg/lb

675/1488

740/1632

Flare/Brazed

Flare/Brazed

POWER SOURCE REFRIGERANT TYPE AIR FLOW

OUTDOOR UNIT

SOUND PRESSURE LEVEL UNIT DIMENSION

PACKING DIMENSION UNIT WEIGHT

TYPE (LIQUID/GAS) PIPE CONNECTION

SIZE

LIQUID

mm/in

19.05 / 3/4

19.05 / 3/4

GAS

mm/in

41.3 / 1 5/8

41.3 / 1 5/8

kg/lb

27/59.5

30/66.1

REFRIGERANT CHARGE

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

MODEL

MASTER UNIT+SLAVE UNIT

NOMINAL COOLING CAPACITY NOMINAL HEATING CAPACITY NOMINAL TOTAL INPUT POWER NOMINAL RUNNING CURRENT

COOLING HEATING COOLING HEATING

POWER SOURCE REFRIGERANT TYPE AIR FLOW

OUTDOOR UNIT

MDS 320B MDS 160BRM + MDS 160BRS 290,020 85,000 313,904 92,000 27,700 25,500 49.5

UNIT DIMENSION

PACKING DIMENSION

Btu/h W Btu/h W W W A A V/Ph/Hz

46.0 380-415 / 3 / 50 R22

HI-FAN

l/s / cfm

3750 + 3750/7945 + 7945

3750 + 3750/7945 + 7945

LOW-FAN

l/s / cfm dB(A) mm/in mm/in mm/in mm/in mm/in mm/in kg/lb

2222 + 2222/4708 + 4708 69 1840/72.4 2590/102.0 840/33.0 2010 + 2101 / 79.1 + 79.1 1030 + 1330 / 40.6 + 52.4 890 + 890 / 35.0 + 35.0 740/1632 Flare/Brazed 19.05 / 3/4 41.3 / 1 5/8 30/66.1

2222 + 2222/4708 + 4708 69 1840/72.4 2590/102.0 840/33.0 2010 +2010 / 79.1 + 79.1 1330 + 1330 / 52.4 + 52.4 890 + 890 / 35.0 + 35.0 750/1653 Flare/Brazed 19.05 / 3/4 41.3 / 1 5/8 30/66.1

SOUND PRESSURE LEVEL HEIGHT WIDTH DEPTH HEIGHT WIDTH DEPTH

UNIT WEIGHT TYPE (LIQUID/GAS) LIQUID SIZE GAS REFRIGERANT CHARGE

PIPE CONNECTION

MDS 300BR MDS 150BRM + MDS 150BRS 272,960 80,000 290,020 85,000 26,200 23,600 46.5 43.1 380-415 / 3 / 50 R22

OUTDOOR UNIT

mm/in mm/in kg/lb

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE. 2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151. 3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW : a) COOLING - 27°C DB / 19°C WB INDOOR AND 35°C DB / 24°C WB OUTDOOR b) HEATING - 20°C DB INDOOR AND 7°C DB / 6°C WB OUTDOOR 4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT THE MACHINE AND 1.42m ABOVE THE MACHINE BASE. 5) THE VALUE OF REFRIGERANT CHARGE IS THE REFRIGERANT CHARGED IN THE OUTDOOR UNIT BEFORE LEAVING FACTORY. THIS CHARGE DOES NOT INCLUDE THE AMOUNT NEEDED FOR EXTENDED PIPING.

115

Components Data MODEL

INDOOR UNIT

MWMD 009G

TYPE

ANTI FUNGUS SKEW FAN

QUANTITY INDOOR FAN

INDOOR FAN MOTOR

1

MATERIAL

ACRYLO NITRILE STYRENE

DRIVE

DIRECT

DIAMETER

mm/in

97/3.8

LENGTH

mm/in

617.5/24.3

TYPE

INDUCTION

QUANTITY

1

INDEX OF PROTECTION (IP)

IP24

MATERIAL TUBE

SEAMLESS INNER GROOVE COPPER TUBE

DIAMETER

mm/in

7.0 / 0.276

THICKNESS

mm/in

0.28 / 0.011

MATERIAL

INDOOR COIL

THICKNESS FACE AREA

FIN

ALUMINIUM (HYDROPHILIC SLIT FIN TYPE) mm/in m 2/ft 2

0.11 / 0.0043 0.201 / 2.161

ROW

2

FIN PER INCH

18

TYPE

NANO FILTER

QUANTITY AIR QUALITY

FILTER

pc

2

mm/in

304/11.9

WIDTH

mm/in

298/11.7

THICKNESS

mm/in

1.5/0.06

LENGTH SIZE

NEGATIVE IONIZER CASING

MODEL

INDOOR UNIT

YES HIGH IMPACT POLYSTYRENE LIGHT GREY

MATERIAL COLOUR

MWMD 010G

INDOOR UNIT TYPE

MWMD 015G ANTI FUNGUS SKEW FAN

QUANTITY INDOOR FAN

INDOOR FAN MOTOR

1

MATERIAL

ACRYLO NITRILE STYRENE

DRIVE

DIRECT

DIAMETER

mm/in

97/3.8

LENGTH

mm/in

717.5/28.2

TYPE

INDUCTION

QUANTITY

1

INDEX OF PROTECTION (IP)

IP24

MATERIAL TUBE

SEAMLESS INNER GROOVE COPPER TUBE

DIAMETER

mm/in

7.0 / 0.276

THICKNESS

mm/in

0.28 / 0.011

MATERIAL

INDOOR COIL

THICKNESS FIN

FACE AREA

ALUMINIUM (HYDROPHILIC SLIT FIN TYPE) 0.11 / 0.0043

mm/in m 2/ft 2

0.234 / 2.516

ROW

2

FIN PER INCH

18

TYPE

NANO FILTER

QUANTITY AIR QUALITY

FILTER SIZE

pc

2

LENGTH

mm/in

304/11.9

WIDTH

mm/in

348/13.7

THICKNESS

mm/in

1.5/0.06

NEGATIVE IONIZER CASING

INDOOR UNIT

YES

MATERIAL COLOUR

HIGH IMPACT POLYSTYRENE LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

116

Components Data MODEL

MWMD 020G

INDOOR UNIT TYPE

MWMD 025G ANTI FUNGUS SKEW FAN

QUANTITY INDOOR FAN

INDOOR FAN MOTOR

1

MATERIAL

ACRYLO NITRILE STYRENE

DRIVE

DIRECT

DIAMETER

mm/in

LENGTH

mm/in

108/4.25 810/31.9 INDUCTION

TYPE

1

QUANTITY

IP20

INDEX OF PROTECTION (IP)

SEAMLESS INNER GROOVE COPPER TUBE

MATERIAL TUBE

DIAMETER

mm/in

7.0 / 0.276

THICKNESS

mm/in

0.28 / 0.011 ALUMINIUM (HYDROPHILIC SLIT FIN TYPE)

MATERIAL

INDOOR COIL FIN

THICKNESS

mm/in

0.11 / 0.0043

FACE AREA

m 2/ft 2

0.269 / 2.900

ROW

2

FIN PER INCH

18 NANO FILTER

TYPE pc

2

mm/in

351/13.8

WIDTH

mm/in

386/15.2

THICKNESS

mm/in

1.5/0.06

QUANTITY AIR QUALITY

FILTER

LENGTH SIZE

YES

NEGATIVE IONIZER MATERIAL COLOUR

CASING

INDOOR UNIT

MODEL

INDOOR UNIT TYPE QUANTITY MATERIAL DRIVE DIAMETER LENGTH TYPE QUANTITY INDEX OF PROTECTION (IP) MATERIAL TUBE DIAMETER THICKNESS MATERIAL THICKNESS FIN FACE AREA ROW FIN PER INCH TYPE QUANTITY FILTER LENGTH SIZE WIDTH THICKNESS

INDOOR FAN

INDOOR FAN MOTOR

INDOOR COIL

AIR QUALITY

PANEL CASING INDOOR UNIT

HIGH IMPACT POLYSTYRENE LIGHT GREY

MCKD 010C

mm/in mm/in

mm/in mm/in mm/in m 2/ft 2

pc mm/in mm/in mm/in MATERIAL FINISHING COLOUR MATERIAL FINISHING COLOUR

MCKD 015C TURBO FAN 1 ASG20 DIRECT 330 / 13 177.76 / 7 INDUCTION 1 SEAMLESS INNER GROOVE COPPER 7.00 / 0.28 0.28 / 0.011 ALUMINIUM (HYDROPHILIC FIN) ALUMINIUM (HYDROPHILIC FIN) 0.11 / 0.0043 0.11 / 0.0043 0.318 / 3.42 0.318 / 3.42 1 2 20 20 WASHABLE SARANET FILTER 1 367.5 / 14.5 381.0 / 15.0 20.8 / 0.8 ABS N/A LIGHT GREY GALVANIZED IRON WITH PE INSULATION GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

117

Components Data MODEL

INDOOR FAN

INDOOR FAN MOTOR

INDOOR COIL

AIR QUALITY

INDOOR UNIT TYPE QUANTITY MATERIAL DRIVE DIAMETER LENGTH TYPE QUANTITY INDEX OF PROTECTION (IP) MATERIAL TUBE DIAMETER THICKNESS MATERIAL THICKNESS FIN FACE AREA ROW FIN PER INCH TYPE QUANTITY LENGTH FILTER SIZE WIDTH THICKNESS PANEL

CASING INDOOR UNIT

MODEL

INDOOR FAN

INDOOR FAN MOTOR

INDOOR COIL

AIR QUALITY

INDOOR UNIT TYPE QUANTITY MATERIAL DRIVE DIAMETER LENGTH TYPE QUANTITY INDEX OF PROTECTION (IP) MATERIAL TUBE DIAMETER THICKNESS MATERIAL THICKNESS FIN FACE AREA ROW FIN PER INCH TYPE QUANTITY LENGTH FILTER SIZE WIDTH THICKNESS PANEL

CASING INDOOR UNIT

MCKD 020C TURBO FAN 1 ASG20 DIRECT 330 / 13 177.76 / 7 INDUCTION 1 SEAMLESS INNER GROOVED COPPER 7.00 / 0.28 0.28 / 0.011 ALUMINIUM (HYDROPHILIC FIN) 0.11 / 0.0043 0.318 / 3.42 2 20 WASHABLE SARANET FILTER 1 367.5 / 14.5 381.0 / 15.0 20.8 / 0.8 ABS N/A LIGHT GREY GALVANIZED IRON WITH PE INSULATION GREY

mm/in mm/in

mm/in mm/in mm/in m 2/ft 2

pc mm/in mm/in mm/in MATERIAL FINISHING COLOUR MATERIAL FINISHING COLOUR

MCKD 020A

MCKD 025A TURBO FAN 1 ASG20 DIRECT 450 / 17.72 169.5 / 6.67 INDUCTION 1 IP22 SEAMLESS COPPER 9.52 / 3/8 0.35 / 0.014 ALUMINIUM (SLIT FIN) ALUMINIUM (SLIT FIN) 0.11 / 0.0043 0.11 / 0.0043 0.469 / 5.022 0.469 / 5.022 2 2 12 16 WASHABLE SARANET FILTER 1 576.0 / 22.7 556.0 / 21.9 22.0 / 0.87 ABS N/A LIGHT GREY GALVANIZED IRON WITH PE INSULATION GREY

mm/in mm/in

mm/in mm/in mm/in m 2/ft 2

pc mm/in mm/in mm/in MATERIAL FINISHING COLOUR MATERIAL FINISHING COLOUR

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

118

Components Data MODEL

INDOOR FAN

INDOOR FAN MOTOR

INDOOR COIL

AIR QUALITY

INDOOR UNIT TYPE QUANTITY MATERIAL DRIVE DIAMETER LENGTH TYPE QUANTITY INDEX OF PROTECTION (IP) MATERIAL DIAMETER TUBE THICKNESS MATERIAL THICKNESS FACE AREA FIN ROW FIN PER INCH TYPE QUANTITY LENGTH FILTER SIZE WIDTH THICKNESS PANEL

CASING INDOOR UNIT

MODEL

INDOOR FAN

INDOOR FAN MOTOR

INDOOR COIL

AIR QUALITY

INDOOR UNIT TYPE QUANTITY MATERIAL DRIVE DIAMETER LENGTH TYPE QUANTITY INDEX OF PROTECTION (IP) MATERIAL TUBE DIAMETER THICKNESS MATERIAL THICKNESS FIN FACE AREA ROW FIN PER INCH TYPE QUANTITY FILTER LENGTH SIZE WIDTH THICKNESS PANEL

CASING INDOOR UNIT

MCKD 030A

MCKD 040A TURBO FAN 1 ASG20 DIRECT 450 / 17.72 169.5 / 6.67 INDUCTION 1 IP22 SEAMLESS INNER GROOVE COPPER SEAMLESS COPPER 9.52 / 3/8 7.00 / 0.28 0.35 / 0.014 0.28 / 0.011 ALUMINIUM (SLIT FIN) ALUMINIUM (HYDROPHILIC FIN) 0.11 / 0.0043 0.11 / 0.0043 0.469 / 5.022 0.469 / 5.022 2 3 16 20 WASHABLE SARANET FILTER 1 576.0 / 22.7 556.0 / 21.9 22.0 / 0.87 ABS N/A LIGHT GREY GALVANIZED IRON WITH PE INSULATION GREY

mm/in mm/in

mm/in mm/in mm/in m 2/ft 2

pc mm/in mm/in mm/in MATERIAL FINISHING COLOUR MATERIAL FINISHING COLOUR

MCKD 050A TURBO FAN 1 ASG20 DIRECT 450 / 17.72 169.5 / 6.67 INDUCTION 1 IP22 SEAMLESS INNER GROOVED COPPER 7.00 / 0.28 0.28 / 0.011 ALUMINIUM (HYDROPHILIC FIN) 0.11 / 0.0043 0.469 / 5.022 3 20 WASHABLE SARANET FILTER 1 576.0 / 22.7 556.0 / 21.9 22.0 / 0.87 ABS N/A LIGHT GREY GALVANIZED IRON WITH PE INSULATION GREY

mm/in mm/in

mm/in mm/in mm/in m 2/ft 2

pc mm/in mm/in mm/in MATERIAL FINISHING COLOUR MATERIAL FINISHING COLOUR

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

119

Components Data MODEL

INDOOR UNIT

MCMD 020E

TYPE

INDOOR FAN

INDOOR FAN MOTOR

CROSS FLOW

QUANTITY

2

MATERIAL

ABS DIRECT

DRIVE DIAMETER

mm/in

LENGTH

mm/in

146 / 5.75 200 / 7.87

TYPE

INDUCTION

QUANTITY

1

INDEX OF PROTECTION (IP)

N/A

MATERIAL TUBE

SEAMLESS INNER GROOVE COPPER

DIAMETER

mm/in

THICKNESS

mm/in

7.00 / 0.276 0.28 / 0.011

MATERIAL

INDOOR COIL FIN

ALUMINIUM (SLIT FIN)

THICKNESS

mm/in

0.11 / 0.0043

FACE AREA

m 2/ft 2

0.27 / 2.90

ROW

2

FIN PER INCH

18 WASHABLE SARANET FILTER

TYPE pc

2

LENGTH

mm/in

309.20 / 12.17

WIDTH

mm/in

383.00 / 15.08

THICKNESS

mm/in

2.25 / 0.09

QUANTITY AIR QUALITY

FILTER SIZE

CASING

MODEL

INDOOR UNIT

MATERIAL

PS

FINISHING

ETCHING SURFACE

COLOUR

LIGHT GREY

INDOOR UNIT

MCMD 025E

INDOOR FAN

INDOOR FAN MOTOR

QUANTITY

2

MATERIAL

ABS DIRECT

DRIVE DIAMETER

mm/in

LENGTH

mm/in

146 / 5.75 200 / 7.87 INDUCTION

TYPE

1

QUANTITY

N/A

INDEX OF PROTECTION (IP)

SEAMLESS INNER GROOVE COPPER

MATERIAL TUBE

DIAMETER

mm/in

THICKNESS

mm/in

7.00 / 0.276 0.28 / 0.011 ALUMINIUM (SLIT FIN)

MATERIAL

INDOOR COIL FIN

THICKNESS

mm/in

0.11 / 0.0043

FACE AREA

m 2/ft 2

0.27 / 2.90

ROW

3

FIN PER INCH

18 WASHABLE SARANET FILTER

TYPE QUANTITY AIR QUALITY

FILTER SIZE

CASING

MCMD 028E CROSS FLOW

TYPE

INDOOR UNIT

pc

2

LENGTH

mm/in

309.20 / 12.17

WIDTH

mm/in

383.00 / 15.08

THICKNESS

mm/in

2.25 / 0.09

MATERIAL

PS

FINISHING

ETCHING SURFACE

COLOUR

LIGHT GREY

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

120

Components Data MODEL

INDOOR UNIT

MCMD 040D

TYPE

INDOOR FAN

INDOOR FAN MOTOR

CROSS FLOW

QUANTITY

4

MATERIAL

ABS

DRIVE

DIRECT

DIAMETER

mm/in

LENGTH

mm/in

146 / 5.75 200 / 7.87

TYPE

INDUCTION

QUANTITY

1

INDEX OF PROTECTION (IP)

N/A

MATERIAL TUBE

SEAMLESS COPPER

DIAMETER

mm/in

9.52 / 3/8

THICKNESS

mm/in

0.35 / 0.014

MATERIAL

INDOOR COIL FIN

ALUMINIUM (HYDROPHILIC)

THICKNESS

mm/in

0.11 / 0.0043

FACE AREA

m 2/ft 2

0.36 / 3.95

ROW

4

FIN PER INCH

12

TYPE

WASHABLE SARANET FILTER pc

2+1

LENGTH

mm/in

544 + 494 / 21.4 + 19.4

WIDTH

mm/in

270 / 10.6

THICKNESS

mm/in

3 / 0.11

MATERIAL

GALVANIZED MILD STEEL

FINISHING

POLYESTER POWDER

COLOUR

LIGHT GREY

QUANTITY AIR QUALITY

FILTER SIZE

CASING

MODEL

INDOOR UNIT

INDOOR UNIT

MCMD 050D

MCMD 062C

TYPE

CROSS FLOW

QUANTITY INDOOR FAN

INDOOR FAN MOTOR

4 ABS

MATERIAL

DIRECT

DIAMETER

mm/in

146 / 5.75

LENGTH

mm/in

200 / 7.87

202 / 7.95 INDUCTION

QUANTITY INDEX OF PROTECTION (IP)

1

2

N/A

N/A

MATERIAL

SEAMLESS INNER GROOVE COPPER

DIAMETER

mm/in

9.52 / 3/8

THICKNESS

mm/in

0.33 / 0.013 ALUMINIUM (HYDROPHILIC)

ALUMINIUM (SLIT FIN)

THICKNESS

mm/in

0.11 / 0.0043

0.11 / 0.0043

FACE AREA

m 2/ft 2

0.36 / 3.95

0.42 / 4.51

MATERIAL

INDOOR COIL FIN

ROW

4

4

FIN PER INCH

12

14

TYPE

WASHABLE SARANET FILTER

QUANTITY FILTER

pc

2+3

mm/in

500 + 400 / 19.6 + 15.7

WIDTH

mm/in

285 / 11.2

THICKNESS

mm/in

3 / 0.11

MATERIAL

GALVANIZED MILD STEEL

FINISHING

POLYESTER POWDER

COLOUR

LIGHT GREY

LENGTH SIZE

CASING

160 / 6.30

TYPE

TUBE

AIR QUALITY

ALU

DRIVE

INDOOR UNIT

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

121

Components Data MODEL

INDOOR UNIT

MCCD 010C

MCCD 015C

TYPE

CENTRIFUGAL

QUANTITY INDOOR FAN

INDOOR FAN MOTOR

1

2

MATERIAL

GALVANIZED STEEL

DRIVE

DIRECT

DIAMETER

mm/in

LENGTH

mm/in

160 / 6.30 202 / 7.95

TYPE

INDUCTION

QUANTITY

1

INDEX OF PROTECTION (IP)

N/A

MATERIAL TUBE

SEAMLESS COPPER

DIAMETER

mm/in

9.52 / 3/8

THICKNESS

mm/in

0.35 / 0.014

MATERIAL

INDOOR COIL FIN

ALUMINIUM (SLIT FIN) mm/in

0.11 / 0.0043

0.11 / 0.0043

FACE AREA

m 2/ft 2

0.115 / 1.238

0.143 / 1.542

ROW

3

3

FIN PER INCH

12

14 WASHABLE SARANET FILTER

TYPE pc

1

LENGTH

mm/in

560 / 22.05

WIDTH

mm/in

195 / 7.68

THICKNESS

mm/in

5 / 0.20

MATERIAL

GALVANIZED STEEL

QUANTITY AIR QUALITY

FILTER SIZE

CASING

MODEL

INDOOR UNIT

FINISHING

WITH PE INSULATION

COLOUR

WITHOUT POWDER PAINT

INDOOR UNIT

MCCD 020C

MCCD 025C

TYPE

INDOOR FAN

INDOOR FAN MOTOR

CENTRIFUGAL

QUANTITY

2

MATERIAL

GALVANIZED STEEL

DRIVE

DIRECT

DIAMETER

mm/in

LENGTH

mm/in

160 / 6.30 202 / 7.95

TYPE

INDUCTION

QUANTITY

1

INDEX OF PROTECTION (IP)

N/A SEAMLESS COPPER

MATERIAL TUBE

DIAMETER

mm/in

9.52 / 3/8

THICKNESS

mm/in

0.35 / 0.014

MATERIAL

INDOOR COIL FIN

ALUMINIUM (CORR. FIN) mm/in

0.11 / 0.0043

0.11 / 0.0043

FACE AREA

m 2/ft 2

0.176 / 1.892

0.203 / 2.187

ROW

3

3

FIN PER INCH

12

12 WASHABLE SARANET FILTER

QUANTITY FILTER SIZE

1

pc

LENGTH

mm/in

860 / 33.86

995 / 39.17

WIDTH

mm/in

195 / 7.68

195 / 7.68

THICKNESS

mm/in

5 / 0.20

5 / 0.20 GALVANIZED STEEL

MATERIAL CASING

ALUMINIUM (SLIT FIN)

THICKNESS

TYPE AIR QUALITY

ALUMINIUM (SLIT FIN)

THICKNESS

INDOOR UNIT

FINISHING

WITH PE INSULATION

COLOUR

WITHOUT POWDER PAINT

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

122

Components Data MODEL

MCCD 030C

INDOOR UNIT

MCCD 040C

TYPE

INDOOR FAN

INDOOR FAN MOTOR

CENTRIFUGAL

QUANTITY

2

MATERIAL

GALVANIZED STEEL

DRIVE

DIRECT

DIAMETER

mm/in

LENGTH

mm/in

214 / 8.43 203.2 / 8.00 INDUCTION

TYPE QUANTITY

1

INDEX OF PROTECTION (IP)

N/A

MATERIAL TUBE

SEAMLESS COPPER

DIAMETER

mm/in

9.52 / 3/8

THICKNESS

mm/in

0.36 / 0.014 ALUMINIUM (CORR. FIN)

ALUMINIUM (CORR. FIN)

THICKNESS

mm/in

0.127 / 0.005

0.127 / 0.005

FACE AREA

m 2/ft 2

0.277 / 2.98

0.31 / 3.44

MATERIAL

INDOOR COIL FIN

ROW

3

3

FIN PER INCH

12

14 WASHABLE SARANET FILTER

TYPE QUANTITY AIR QUALITY

FILTER SIZE

pc

2

LENGTH

mm/in

449 / 17.68

507 / 19.96

WIDTH

mm/in

305 / 12.01

305 / 12.01

THICKNESS

mm/in

5 / 0.20

5 / 0.20

MATERIAL CASING

MODEL

INDOOR UNIT

GALVANIZED STEEL

FINISHING

WITH PE INSULATION

COLOUR

WITHOUT POWDER PAINT

INDOOR UNIT

MCCD 050C

MCCD 060C

TYPE

INDOOR FAN

INDOOR FAN MOTOR

CENTRIFUGAL

QUANTITY

2

MATERIAL

GALVANIZED STEEL

DRIVE

DIRECT

DIAMETER

mm/in

LENGTH

mm/in

214 / 8.43 203.2 / 8.00

TYPE

INDUCTION

QUANTITY

1

INDEX OF PROTECTION (IP)

N/A

MATERIAL TUBE

SEAMLESS COPPER

DIAMETER

mm/in

9.52 / 3/8

THICKNESS

mm/in

0.35 / 0.014

MATERIAL

INDOOR COIL FIN

ALUMINIUM (CORR. FIN)

ALUMINIUM (CORR. FIN)

THICKNESS

mm/in

0.127 / 0.005

0.127 / 0.005

FACE AREA

m 2/ft 2

0.40 / 4.40

0.47 / 5.16

ROW

3

3

FIN PER INCH

14

14 WASHABLE SARANET FILTER

TYPE QUANTITY AIR QUALITY

FILTER SIZE

2

pc

LENGTH

mm/in

634 / 24.96

734 / 28.90

WIDTH

mm/in

305 / 12.01

305 / 12.01

THICKNESS

mm/in

5 / 0.20

5 / 0.20 GALVANIZED STEEL

MATERIAL CASING

INDOOR UNIT

FINISHING

WITH PE INSULATION

COLOUR

WITHOUT POWDER PAINT

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

123

Components Data MODEL

INDOOR UNIT

MDBD 080

TYPE

INDOOR FAN

INDOOR FAN MOTOR

QUANTITY

2

MATERIAL

IRON

DRIVE

DIRECT

V DRIVE

DIAMETER

mm/in

250 / 9.8

254 / 10.0

LENGTH

mm/in

361 / 14.2

348 / 13.7

DIRECT

V DRIVE

TYPE QUANTITY

1

INDEX OF PROTECTION (IP) MATERIAL TUBE

DIAMETER

mm/in

THICKNESS

mm/in

MATERIAL

INDOOR COIL FIN

IP20

IP55

INNER GROOVE COPPER

PLAIN COPPER

9.52 / 3/8 0.28 / 0.01

0.33 / 0.01 ALUMINIUM (HYDROPHILIC)

THICKNESS

mm/in

0.11 / 0.004

0.11 / 0.004

FACE AREA

m2/ft2

0.498 / 0.020

0.640 / 0.025

4

4

FIN PER INCH TYPE QUANTITY FILTER

INDOOR UNIT

12

14

PP12x17H/B

PP21x17H/B

pc LENGTH

SIZE

CASING

9.52 / 3/8

ALUMINIUM (HYDROPHILIC)

ROW

AIR QUALITY

MDBD 100 TURBO FAN

1

mm/in

1396 / 55.0

1396 / 55.0

WIDTH

mm/in

345 / 13.6

418 / 16.5

THICKNESS

mm/in

21 / 0.8

10 / 0.4

MATERIAL

WOODEN

COLOUR

YELLOW

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

124

Components Data MODEL

OUTDOOR UNIT TYPE

OUTDOOR FAN

1

2

MATERIAL

ASG20

ASG20

DIRECT DRIVE

DIRECT DRIVE

DIAMETER

mm/in

TYPE

460 / 18.1

420 / 16.5

ASYNCHRONOUS MOTOR

ASYNCHRONOUS MOTOR

QUANTITY

1

INDEX OF PROTECTION (IP) TYPE COMPRESSOR

OIL TYPE OIL AMOUNT

3

cm / fl.oz.

MATERIAL TUBE

FIN

MODEL

MINERAL OIL

1242 / 42.0

1242 / 42.0

COPPER

COPPER 9.52 / 3/8

mm/in

0.32 / 0.0126

0.32 / 0.0126

ALUMINUM

ALUMINUM

THICKNESS

mm/in

0.11 / 0.0043

0.11 / 0.0043

FACE AREA

m /ft

0.74 / 7.97

1.06 / 11.40

2

2

ROW

2

2

FIN PER INCH

14

14

MATERIAL

EG

COLOUR

Light Grey (RAL7032)

OUTDOOR UNIT

EG Light Grey (RAL7032)

MDS 050A

MDS 060A

PROPELLER FAN

PROPELLER FAN

QUANTITY

2

2

MATERIAL

ASG20

ASG20

DIRECT DRIVE

DIRECT DRIVE

mm/in

420 / 16.5 ASYNCHRONOUS MOTOR

TYPE QUANTITY INDEX OF PROTECTION (IP)

OIL TYPE OIL AMOUNT

3

cm / fl.oz.

MATERIAL TUBE

FIN

2 IP 44 ZRD68KC-PFZ / ZRD72KC-TFD

MINERAL OIL

MINERAL OIL

1893 / 64.0

1893 / 64.0

COPPER

COPPER

mm/in

9.52 / 3/8

9.52 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

0.32 / 0.0126

THICKNESS

mm/in

FACE AREA

m /ft

2

2

ALUMINUM

ALUMINUM

0.11 / 0.0043

0.11 / 0.0043

1.06 / 11.40

1.27 / 13.67

ROW

2

2

FIN PER INCH

14

14

MATERIAL COLOUR

2

DIAMETER

MATERIAL

OUTDOOR COIL

460 / 18.1 ASYNCHRONOUS MOTOR

IP 44 ZRD61KC-PFZ / ZRD61KC-TFD

TYPE (1Ø / 3Ø)

CASING

MINERAL OIL

THICKNESS

DIAMETER

COMPRESSOR

IP 44 ZRD48KC

9.52 / 3/8

DRIVE

OUTDOOR FAN MOTOR

IP 44 ZRD42KC

mm/in

TYPE

OUTDOOR FAN

2

DIAMETER

MATERIAL

OUTDOOR COIL

CASING

MDS 040A PROPELLER FAN

QUANTITY

DRIVE

OUTDOOR FAN MOTOR

MDS 030A PROPELLER FAN

EG Light Grey (RAL7032)

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

125

EG Light Grey (RAL7032)

Components Data MODEL

OUTDOOR UNIT

MDS 070A

TYPE

OUTDOOR FAN

PROPELLER FAN

QUANTITY

2

MATERIAL

ASG20

DRIVE

DIRECT DRIVE

DIAMETER

460 / 18.1

mm/in

TYPE OUTDOOR FAN MOTOR

ASYNCHORONOUS MOTOR

QUANTITY

2 IP 44

INDEX OF PROTECTION (IP) TYPE COMPRESSOR

ZRD81KC

OIL TYPE

MINERAL OIL 3 cm / fl.oz.

OIL AMOUNT

1680 / 56.8 COPPER

MATERIAL TUBE

THICKNESS

mm/in

0.32 / 0.0126

mm/in 2 2 m /ft

0.11 / 0.0043

9.5 /

ALUMINUM

THICKNESS FIN

MODEL

mm/in

MATERIAL

OUTDOOR COIL

CASING

DIAMETER

FACE AREA

0.99 / 10.66

ROW

3

FIN PER INCH

14

MATERIAL

EG

COLOUR

Light Grey (RAL7032)

OUTDOOR UNIT TYPE

OUTDOOR FAN

1

1

MATERIAL

ASG30

ASG30

DIRECT DRIVE

DIRECT DRIVE

DIAMETER

mm/in

TYPE

750 / 29.5

750 / 29.5

ASYNCHRONOUS MOTOR

ASYNCHRONOUS MOTOR

QUANTITY

1

INDEX OF PROTECTION (IP)

IP 44

TYPE COMPRESSOR

ZRD61KC + ZR54KC

OIL TYPE OIL AMOUNT

3

cm / fl.oz.

FIN

IP 44 ZRD61KC + ZR61KC

MINERAL OIL

MINERAL OIL 1,686 + 1,686 / 68.6 + 68.6

COPPER

COPPER

DIAMETER

mm/in

9.52 / 3/8

9.52 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

0.32 / 0.0126

ALUMINUM

ALUMINUM

0.11 / 0.0043

0.11 / 0.0043

1.71 / 8.4

1.71 / 8.4

MATERIAL

OUTDOOR COIL

1

1,686 + 1,952 / 59.3 + 68.7

MATERIAL TUBE

CASING

MDS 100B PROPELLER FAN

QUANTITY

DRIVE

OUTDOOR FAN MOTOR

MDS 080B PROPELLER FAN

THICKNESS

mm/in

FACE AREA

m /ft

2

2

ROW

2

3

FIN PER INCH

16

16

MATERIAL

EG

COLOUR

Light Grey (RAL7032)

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

126

EG Light Grey (RAL7032)

Components Data MODEL

OUTDOOR UNIT TYPE

OUTDOOR FAN

1

1

MATERIAL

ASG30

ASG30

DIRECT DRIVE

DIRECT DRIVE

DIAMETER

mm/in

TYPE

750 / 29.5 ASYNCHRONOUS MOTOR

QUANTITY INDEX OF PROTECTION (IP) TYPE

COMPRESSOR

3

cm / fl.oz.

FIN

MODEL

MINERAL OIL

COPPER mm/in

9.52 / 3/8

9.52 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

0.32 / 0.0126

ALUMINUM

ALUMINUM

0.11 / 0.0043

0.11 / 0.0043

1.71 / 18.4

2.30 / 24.75

THICKNESS

mm/in

FACE AREA

m /ft

2 2

ROW

3

3

FIN PER INCH

16

16

MATERIAL

EG

COLOUR

Light Grey (RAL7032)

OUTDOOR UNIT

MDS 180B

MDS 200B

PROPELLER FAN

PROPELLER FAN

2

2

MATERIAL

ASG30

ASG30

DIRECT DRIVE

DIRECT DRIVE

mm/in

TYPE

750 / 29.5

750 / 29.5

ASYNCHRONOUS MOTOR

ASYNCHRONOUS MOTOR

QUANTITY INDEX OF PROTECTION (IP)

OIL TYPE 3

cm / fl.oz.

1.893 + 1.893x2 / 68.6 + 68.6x2 COPPER

MATERIAL

FIN

ZRD61KC + ZR61KC x 3 MINERAL OIL 1.686 + 1.686x3 / 59.3 + 59.3x3 COPPER

DIAMETER

mm/in

9.52 / 3/8

9.52 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

0.32 / 0.0126

ALUMINUM

ALUMINUM

THICKNESS

mm/in

0.11 / 0.0043

0.11 / 0.0043

FACE AREA

m /ft

3.42 / 36.8

3.42 / 36.8

MATERIAL

OUTDOOR COIL

2 IP 44

MINERAL OIL

OIL AMOUNT

TUBE

2 IP 44 ZRD72KC + ZR72KC x 2

TYPE

CASING

EG Light Grey (RAL7032)

QUANTITY

DIAMETER

COMPRESSOR

COPPER

DIAMETER

DRIVE

OUTDOOR FAN MOTOR

ZRD61KC + ZR61KC x 2

1.686 + 1.686x2 / 59.3 + 59.3x2

TYPE

OUTDOOR FAN

1 IP 44

1.893 + 1.893 / 59.3 + 59.3

MATERIAL

OUTDOOR COIL

1

MINERAL OIL

MATERIAL TUBE

750 / 29.5 ASYNCHRONOUS MOTOR

IP 44 ZRD72KC + ZR72KC

OIL TYPE OIL AMOUNT

CASING

MDS 150B PROPELLER FAN

QUANTITY

DRIVE

OUTDOOR FAN MOTOR

MDS 120B PROPELLER FAN

2

2

ROW

3

3

FIN PER INCH

16

16

MATERIAL

EG

COLOUR

Light Grey (RAL7032)

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

127

EG Light Grey (RAL7032)

Components Data MODEL

OUTDOOR UNIT TYPE

OUTDOOR FAN

2

2

MATERIAL

ASG30

ASG30

DIRECT DRIVE

DIRECT DRIVE

DIAMETER

mm/in

TYPE

750 / 29.5

750 / 29.5

ASYNCHRONOUS MOTOR

ASYNCHRONOUS MOTOR

QUANTITY INDEX OF PROTECTION (IP)

OIL AMOUNT

3

cm / fl.oz.

CASING

MODEL

1.893 + 1.893x3 / 68.6 + 68.6x3 COPPER

DIAMETER

mm/in

9.52 / 3/8

9.52 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

0.32 / 0.0126

ALUMINUM

ALUMINUM

THICKNESS

mm/in

0.11 / 0.0043

0.11 / 0.0043

FACE AREA

m /ft

3.42 / 36.8

3.42 / 36.8

2

2

ROW

3

3

FIN PER INCH

16

16

MATERIAL

EG

COLOUR

Light Grey (RAL7032)

OUTDOOR UNIT TYPE

OUTDOOR FAN

MDS 280B PROPELLER FAN

2

2

ASG30

ASG30

DIRECT DRIVE

DIRECT DRIVE

mm/in

750 / 29.5 ASYNCHRONOUS MOTOR

TYPE QUANTITY INDEX OF PROTECTION (IP)

OIL AMOUNT

3

cm / fl.oz.

COPPER

FIN

MINERAL OIL 1.686 + 1.686x5 / 59.3 + 59.3x5 COPPER

mm/in

9.52 / 3/8

9.52 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

0.32 / 0.0126

ALUMINUM

ALUMINUM

THICKNESS

mm/in

0.11 / 0.0043

0.11 / 0.0043

FACE AREA

m /ft

4.01 / 43.15

4.6 / 49.5

2

2

ROW

3

3

FIN PER INCH

16

16

EG

MATERIAL COLOUR

ZRD61KC + ZR61KCx5

DIAMETER

MATERIAL

OUTDOOR COIL

2 IP 44

1.893 - 1.893 - 1.686x3 / 68.6 + 68.6 + 59.3x3

MATERIAL TUBE

2

MINERAL OIL

OIL TYPE

750 / 29.5 ASYNCHRONOUS MOTOR

IP 44 ZRD72KC + ZR72KC + ZR61KCx3

TYPE

CASING

MDS 260B PROPELLER FAN

MATERIAL

DIAMETER

COMPRESSOR

EG Light Grey (RAL7032)

QUANTITY

DRIVE

OUTDOOR FAN MOTOR

MINERAL OIL

COPPER

MATERIAL

FIN

ZRD72KC + ZR72KC x 3

1.893 + 1.686x3 / 68.6 + 59.3x3

MATERIAL

OUTDOOR COIL

2 IP 44

MINERAL OIL

OIL TYPE

TUBE

2 IP 44

ZRD72KC + ZR61KC x 3

TYPE COMPRESSOR

MDS 240B PROPELLER FAN

QUANTITY

DRIVE

OUTDOOR FAN MOTOR

MDS 220B PROPELLER FAN

Light Grey (RAL7032)

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

128

EG Light Grey (RAL7032)

Components Data MODEL

OUTDOOR UNIT TYPE

OUTDOOR FAN

2

2

MATERIAL

ASG30

ASG30

DIRECT DRIVE

DIRECT DRIVE

DIAMETER

mm/in

750 / 29.5 ASYNCHRONOUS MOTOR

TYPE

TYPE

2

2 IP 44

ZRD61KC + ZR61KCx5

ZRD72KC + ZR72KC + ZR61KCx4

MINERAL OIL

OIL TYPE OIL AMOUNT

3

cm / fl.oz.

1.893 + 1.893 + 1.686x4 / 68.6 + 68.6 + 59.3x4

COPPER

COPPER

FIN

CASING

MODEL

DIAMETER

mm/in

9.52 / 3/8

9.52 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

0.32 / 0.0126

ALUMINUM

ALUMINUM

THICKNESS

mm/in

0.11 / 0.0043

0.11 / 0.0043

FACE AREA

m /ft

4.6 / 49.5

4.6 / 49.5

MATERIAL

OUTDOOR COIL

2

2

ROW

3

3

FIN PER INCH

16

16

MATERIAL

EG

COLOUR

Light Grey (RAL7032)

OUTDOOR UNIT TYPE

OUTDOOR FAN

MDS 040AR PROPELLER FAN

1

2

ASG20

ASG20

DIRECT DRIVE

DIRECT DRIVE

460 / 18.1

420 / 16.5

mm/in

TYPE

ASYNCHRONOUS MOTOR

QUANTITY INDEX OF PROTECTION (IP)

OIL TYPE OIL AMOUNT

3

cm / fl.oz.

MATERIAL TUBE

FIN

2

IP 44

IP 44 ZRD48KC

MINERAL OIL

MINERAL OIL

1242 / 42.0

1242 / 42.0

COPPER

COPPER

DIAMETER

mm/in

9.52 / 3/8

9.52 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

0.32 / 0.0126

ALUMINUM

ALUMINUM

THICKNESS

mm/in

0.11 / 0.0043

0.11 / 0.0043

FACE AREA

m /ft

0.74 / 7.97

1.06 / 11.40

2

2

MATERIAL

OUTDOOR COIL

ASYNCHRONOUS MOTOR

1

ZRD42KC

TYPE

2

2

ROW FIN PER INCH CASING

MDS 030AR PROPELLER FAN

MATERIAL

DIAMETER

COMPRESSOR

EG Light Grey (RAL7032)

QUANTITY

DRIVE

OUTDOOR FAN MOTOR

MINERAL OIL

1.686 + 1.686x5 / 59.3 + 59.3x5

MATERIAL TUBE

750 / 29.5 ASYNCHRONOUS MOTOR

IP 44

QUANTITY INDEX OF PROTECTION (IP)

COMPRESSOR

MDS 320B PROPELLER FAN

QUANTITY

DRIVE

OUTDOOR FAN MOTOR

MDS 300B PROPELLER FAN

MATERIAL

14

14

EG

EG

Light Grey (RAL7032)

COLOUR

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

129

Light Grey (RAL7032)

Components Data MODEL

OUTDOOR UNIT TYPE

OUTDOOR FAN

2

ASG20

ASG20

DIRECT DRIVE

DIRECT DRIVE

mm/in

420 / 16.5

460 / 18.1

ASYNCHRONOUS MOTOR

QUANTITY INDEX OF PROTECTION (IP)

OIL TYPE OIL AMOUNT

3

cm / fl.oz.

MATERIAL TUBE

FIN

2

2

IP 44

IP 44

MINERAL OIL

1893 / 64.0

1893 / 64.0

COPPER

COPPER

mm/in

9.52 / 3/8

9.52 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

0.32 / 0.0126

ALUMINUM

ALUMINUM

0.11 / 0.0043

0.11 / 0.0043

1.06 / 11.40

1.27 / 13.67

THICKNESS

mm/in

FACE AREA

m /ft

2

2

ROW

2

2

FIN PER INCH

14

14

MATERIAL

EG

COLOUR

EG

Light Grey (RAL7032)

OUTDOOR UNIT

PROPELLER FAN

QUANTITY

2

MATERIAL

ASG20

DRIVE

DIRECT DRIVE

DIAMETER

mm/in

460 / 18.1

TYPE OUTDOOR FAN MOTOR

ASYNCHORONOUS MOTOR

QUANTITY

2

INDEX OF PROTECTION (IP)

IP 44

TYPE COMPRESSOR

ZRD81KC

OIL TYPE

MINERAL OIL

OIL AMOUNT

3

1680 / 56.8

cm / fl.oz.

MATERIAL TUBE

COPPER

DIAMETER

mm/in

9.5 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

THICKNESS

mm/in

0.11 / 0.0043

FACE AREA

m /ft

2

0.99 / 10.66

MATERIAL

OUTDOOR COIL FIN

CASING

Light Grey (RAL7032)

MDS 070AR

TYPE

OUTDOOR FAN

ZRD68KC-PFZ / ZRD72KC-TFD

MINERAL OIL

DIAMETER

MATERIAL

OUTDOOR COIL

ASYNCHRONOUS MOTOR

ZRD61KC-PFZ / ZRD61KC-TFD

TYPE (1Ø/3Ø)

MODEL

PROPELLER FAN

MATERIAL

TYPE

CASING

PROPELLER FAN 2

DIAMETER

COMPRESSOR

MDS 060AR

QUANTITY

DRIVE

OUTDOOR FAN MOTOR

MDS 050AR

ALUMINUM

2

ROW

3

FIN PER INCH

14

MATERIAL

EG

COLOUR

Light Grey (RAL7032)

1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.

130

Components Data MODEL

OUTDOOR UNIT TYPE

OUTDOOR FAN

1

1

MATERIAL

ASG30

ASG30

DIRECT DRIVE

DIRECT DRIVE

mm/in

DIAMETER

750 / 29.5 ASYNCHRONOUS MOTOR

TYPE

1

QUANTITY

IP 44

INDEX OF PROTECTION (IP)

ZRD61KC + ZR54KC

TYPE COMPRESSOR

3 cm / fl.oz.

MINERAL OIL

COPPER

MODEL

mm/in

9.52 / 3/8

9.52 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

0.32 / 0.0126

ALUMINUM

ALUMINUM

mm/in 2 2 m /ft

0.11 / 0.0043

0.11 / 0.0043

1.71 / 8.4

1.71 / 8.4

FACE AREA ROW

2

3

FIN PER INCH

16

16

EG

MATERIAL COLOUR

Light Grey (RAL7032)

MDS 120BR

MDS 150BR

PROPELLER FAN

PROPELLER FAN

OUTDOOR UNIT

QUANTITY

1

1

MATERIAL

ASG30

ASG30

DIRECT DRIVE

DIRECT DRIVE

DRIVE DIAMETER

mm/in

TYPE OUTDOOR FAN MOTOR

750 / 29.5 ASYNCHRONOUS MOTOR

QUANTITY INDEX OF PROTECTION (IP) TYPE

COMPRESSOR

FIN

MINERAL OIL 1.686 + 1.686x2 / 59.3 + 59.3x2

COPPER

COPPER

mm/in

9.52 / 3/8

9.52 / 3/8

THICKNESS

mm/in

0.32 / 0.0126

0.32 / 0.0126

THICKNESS

mm/in

FACE AREA

m /ft

2

2

ALUMINUM

ALUMINUM