Solid Sawn Joist Hangers
HUCQ Heavy-Duty Joist Hangers FACE MOUNT HANGERS – SOLID SAWN LUMBER (DF/SP)
Typical HUCQ Installation on a Post
HUCQ410
Typical HUCQ Installation on a Beam
These products are available with additional corrosion protection. Additional products on this page may also be available with this option, check with Simpson Strong-Tie for details.
Dimensions Model No.
Fasteners
Allowable Loads DF/SP
Joist
W
H
B
Face
HUCQ310-SDS
2 9⁄16
9
3
8-SDS 1⁄4"x2 1⁄2"
4-SDS 1⁄4"x2 1⁄2"
HUCQ210-2-SDS
3 1⁄4
9
3
12-SDS 1⁄4"x2 1⁄2"
6-SDS 1⁄4"x2 1⁄2"
HUCQ410-SDS
9
3 ⁄16
9
3
12-SDS ⁄4"x2 ⁄2"
6-SDS ⁄4"x2 ⁄2"
2510
4680
HUCQ412-SDS
39⁄16
11
3
14-SDS 1⁄4"x2 1⁄2"
6-SDS 1⁄4"x2 1⁄2"
2510
5460
HUCQ210-3-SDS
4 5⁄8
9
3
12-SDS 1⁄4"x2 1⁄2"
6-SDS 1⁄4"x2 1⁄2"
2510
4680
HUCQ610-SDS
1
5 ⁄2
9
3
12-SDS ⁄4"x2 ⁄2"
6-SDS 1⁄4"x2 1⁄2"
2520
4680
HUCQ612-SDS
5 1⁄2
11
3
14-SDS 1⁄4"x2 1⁄2"
6-SDS 1⁄4"x2 1⁄2"
2520
5315
5315
1
1
1
1
1
1. Uplift loads have been increased for wind or earthquake loading. Reduce where other loads govern. 2 See page 101 for additional engineered wood product sizes.
Uplift (160)
1
SPF/HF Uplift (160)
Floor (100)
Snow (115)
985
2245
2585
2810
1805
3370
3570
3570
Code Ref.
Floor (100)
Snow (115)
Roof (125)
Roof (125)
1370
3120
3590
3900
2510
4680
4955
4955
4955
4955
1805
3370
3570
3570
5560
5560
1805
3930
4005
4005
4955
4955
1805
3370
3570
3570
F23
5380
5715
1815
3370
3875
4115
5315
1815
3825
3825
3825
I9, L12, F23
Solid Sawn Joist Hangers
The HUCQ series are heavy-duty joist hangers that incorporate Simpson Strong-Tie® Strong-Drive® SDS Heavy-Duty Connector screws. Designed and tested for installation at the end of a beam or on a post, they provide a strong connection with fewer fasteners than nailed hangers. See page 117 for structural composite lumber hangers. MATERIAL: 14 gauge FINISH: Galvanized. Most models available in stainless steel or ZMAX® coating. INSTALLATION: • Use all specified fasteners. See General Notes. • Install 1⁄4"x2 1⁄2" Strong-Drive SDS Heavy-Duty Connector screws, which are provided, in all round holes. (Lag screws will not achieve the same load.) • For use on solid sawn wood members. OPTIONS: These hangers cannot be modified. CODES: See page 12 for Code Reference Key Chart.
F23 L12, F23, I9
3. Structural composite lumber columns have sides that show either the wide face or the edges of the lumber strands/veneers. Values in the tables reflect installation into the wide face. See technical bulletin T-SCLCOLUMN for values on the narrow face (edge).
Min/Max: Refers to min. or max. nailing for products with round and triangle holes. Min. nailing uses round holes, and max. nailing uses round and triangle holes to achieve maximum load.
This icon identifies products approved for installation with the Simpson Strong-Tie® Strong-Drive® SD Connector screw. See page 27 for more information. Joist Size: This shows the size of joist member.
Joist Size
DBL 2X6
Model No.: This is the Simpson Strong-Tie product name.
Model No.
LUS26-2 U26-2 HUS26-2/HUSC26-2 HU26-2/HUC26-2
This icon identifies products that are available with additional corrosion protection. See pages 13-15 for additional information.
Nails: This shows the fastener quantity and type required to achieve the table loads.
Gauge: Product material
Ga
18 16 14 14 14
Dimensions (in.) W 3 1⁄8 3 1⁄8 3 1⁄8 3 1⁄8 3 1⁄8
H
B
4 7⁄8 2 5 2 5 3⁄16 2 5 3⁄8 2 1⁄2 5 3⁄8 2 1⁄2
Min/ Max — — — Min Max
Code Ref.: See page 12 for the Code Reference Key Chart, to determine which code reports include this product.
Allowable Design Loads: The maximum load that a connection is designed to provide. There may be multiple design loads acting in different directions (up, down, lateral, perpendicular, etc.) imposed on a connection. Installed Cost Index: Uplift Floor, Snow, Roof This indicates the products relative installed cost (combined cost and installation cost).
DF/SP Allowable Loads Uplift Floor Snow Roof Header Joist (160) (100) (115) (125) SAWN LUMBER SIZES 4-16d 4-16d 1165 1030 1180 1280 8-16d 4-10d 740 1150 1305 1410 4-16d 4-16d 1235 1065 1210 1305 8-16d 4-10d 760 1190 1345 1445 12-16d 6-10d 1135 1785 2015 2165
Dimensions W, H, B: This shows the product dimensions (width, height and base in this case.) referenced in the product drawing.
CATALOG DEFINITION: Deflection: The distance a point moves when a load is applied.
Load Duration: Assumed duration factor used to determine the allowable load.
Fasteners
Installed Cost Index (ICI)
Code Ref.
Lowest +65% +172% +233% +254%
I7, I27, F6, L5, L17
NAILS: 16d = 0.162" dia. x 3 1⁄2" long, 10dx1 1⁄2 = 0.148" dia. x 1 1⁄2" long. See pages 22-23 for other nail sizes and information. Throughout this catalog a footnote will typically be provided indicating the required nail diameter and length. All installations should be designed only in accordance with the allowable load values set forth in this catalog.
I7, F6, L17 I7, I27, F6, L5, L17 I7, F6, L17
Product Drawing: Provides a graphic presentation of the product H with dimensional information (often cross referenced to the table).
W
B
C-C-2015 © 2015 SIMPSON STRONG-TIE COMPANY INC. PRINTED 12/14
LOAD TABLE EXPLANATION
75