Model 527 Bolster Extensions

Page 1

Copyright ©2023 PFA, Inc. All rights reserved. Reproduction or use in any manner of editorial or graphic content herein without the express written permission of PFA, Inc. is strictly prohibited. Every effort has been made to ensure the information within this publication is complete and accurate at the time of printing. S3203 BE 527 REV A – 7/23 pfa-inc.com N118 W18251 Bunsen Drive Germantown,WI 53022 (262) 250-4410 • Fax (262) 250-4409 MODEL 527 BOLSTER EXTENSIONS
pfa-inc.com MODEL 527 | BOLSTER EXTENSIONS | PAGE 3 TABLE OF CONTENTS 1. Introduction 4 2. Installation 5 3. Operating Instructions .....................................................................................6 4. Maintenance 7 5. Drawing 527 8 6. Drawing 6113 10 7. Drawing 6527 12 8. Drawing 5308 14 9. Drawing 14667 16 10. Drawing 5602 ........................................................................................... 18 11. Drawing 5974 20 12. Drawing 5315 22 13. Drawing 5338 24 14. Drawing 5320 ........................................................................................... 26

NOTICE: The following instructions are guidelines written for experienced mechanics who takes proper safety precautions. All work should be performed to local and internal safety requirements and approved by the company safety officer or appropriate authority. Only experienced mechanics should perform installation of Bolster Extension mounting brackets.

CAUTION: BOLSTER EXTENSIONS ARE DESIGNED FOR SPECIFIC WEIGHT LIMITS.

MODEL BE-527 - DO NOT EXCEED 6,000 LBS. FOR EACH PAIR (3,000 LBS. PER ARM).

MODEL BE-527HD – DO NOT EXCEED 8,000 LBS. FOR EACH PAIR (4,000 LBS. PER ARM).

CAUTION: TO AVOID DAMAGE TO EQUIPMENT AND PERSONAL INJURY, USE MOUNTING BOLTS SUPPLIED WITH EACH BOLSTER EXTENSION. IF REPLACED, USE ONLY BOLTS WITH A TENSILE STRENGTH OF 170,000 PSI MINIMUM. ENSURE ADEQUATE THREAD ENGAGEMENT FOR ALL SCREWS.

CAUTION: REVIEW ENTIRE INSTALLATION PROCEDURE PRIOR TO INSTALLATION TO ENSURE CONSIDERATION IS GIVEN TO SPACING, LEVELING, AND MOUNTING HOLE LOCATIONS AND ADJUSTMENT.

pfa-inc.com MODEL 527 | BOLSTER EXTENSIONS | PAGE 4
INTRODUCTION

INSTALLATION

Note: Refer to Dwg 527 and assembly drawing for specific length referred to on Dwg 527.

Note: Verify that the SHCS and roll pins are of the proper length for the installation.

1. If the bolster extension is to be used without die lifters then the top of the rollers should be on the same plane as the bolster surface.

2. If die lifters are used install those first.

3. Use a straight edge against bolster surface or elevated die lifter rail bearings to project the plane which the bolster extension rollers must be at after installation. Ideally, a flat plate which rests on both die lifters simultaneously and hangs over the edge of the bolster should be used. The bolster extension mounting bracket can then be placed against the bolster side and lifted upward until the rollers touch the plate. The center for the mounting screws can then be determined and a punch used to create a drill point.

4. Drill and tap the hole for the ¾-10 mounting screws. Make sure that the horizontal centerline of the holes is parallel with the bolster surface. See drawings for location of holes. (Note template is no longer used – carefully calculate locations and review entire procedure for details on when to match drill holes for the roll pins).

5. Secure the mounting bracket with the mounting screws using light torque and check for proper elevation and level.

6. If the bolster extension rollers are not on the correct plane the screw clearance holes allow for some adjustment. In that case, back off the screws slightly so that you can move the bracket using a soft hammer or the like.

7. Make sure that the rollers are on plane with the die lifter rollers (hinge pin is perpendicular - rollers are at the proper height). If additional adjustments are necessary use a reamer to remove paint from clearance holes or oval holes slightly to allow movement up or down and shim the back of the flange on the top or bottom as needed.

8. After adjustment secure the screws using proper torque - confirm alignment.

9. Verify that the bolster extension swings and locks in all three positions, i.e. straight out and 90° left and right.

10. After securing all screws transfer drill holes for the two roll pins. Then drive those pins in to finish the installation. Pins should be flush with bracket.

pfa-inc.com MODEL 527 | BOLSTER EXTENSIONS | PAGE 5

OPERATING INSTRUCTIONS

Note: The Model - 527 Bolster Extension can be stowed in the 90° left or right position.

CAUTION: WHEN DIES ARE LOADED AND UNLOADED, THE BOLSTER EXTENSION MUST BE SECURELY LOCKED.

1. Pull the Locking Mechanism Lever located under the bolster extension forward to the unlock position and move Bolster Extension from the 90° left or right position.

2. Release Locking Mechanism Lever after the Bolster Extension is moved about 30°. The lock will then engage automatically when the next lock position is reached.

Note: The Locking Mechanism is spring loaded to lock when the groove in the hinge lines up with the locking mechanism. If the spring breaks replace it immediately.

3. Inspect Bolster Extension to ensure that it is properly positioned and securely locked.

4. Place die carefully onto the Bolster Extensions inside the spring loaded die stops.

CAUTION: DO NOT EXCEED RATED LOAD LIMIT.

5. Roll die onto bolster.

To stow Bolster Extension in the 90° left or right position pull Locking Mechanism Lever to the forward unlock position and swing Bolster Extension to the left or right.

CAUTION: MAKE SURE DIE IS WIDE ENOUGH (L-R DIMENSION) TO BE ROLLED SAFELY ON THE BOLSTER EXTENSIONS.

pfa-inc.com MODEL 527 | BOLSTER EXTENSIONS | PAGE 6

MAINTENANCE

Each user must implement an inspection system which covers the following and other relevant factors which may exist in a given location.

1. Establish inspection intervals based on frequency of use, abuse and other relevant factors.

2. Check to ensure that spring loaded die stop at the tip of the Bolster Extension is normally in the up position and that Locking Mechanism Lever, located under the Bolster Extension is operating freely. Replace or repair as necessary.

CAUTION: MAKE SURE THAT THE LOCKING MECHANISM RETURN SPRINGS ARE OPERATIONAL.

3. Check condition of mounting bracket and bolster extension interface. Make any necessary repairs.

4. Replace any damaged rollers.

5. Make sure all fasteners are tight.

6. Make sure the maximum die weight is not exceeded.

7. Remind fork lift operators to avoid damaging Bolster Extensions.

8. Instruct personnel to inform safety engineers in the event of a forklift collision with bolster extension.

9. Other relevant factors as determined by the user.

pfa-inc.com MODEL 527 | BOLSTER EXTENSIONS | PAGE 7

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

'A' DIM 'B'

DIM

DIM 'C' MODEL DIM A DIM B DIM C 527-20 527-24 527-28 527-32 527-36 527-40 527-16 527-18 527-22 20.41 24.41 28.41 32.42 36.06 40.22 16.41 18.41 22.41 22.52 26.52 30.52 34.52 38.16 42.32 18.52 20.52 24.52 7.20 9.15 9.15 9.15 11.90 11.90 7.20 7.20 9.15

BOLSTER EXTENSION REV -

MODEL PAGE 1 OF 2

3. A LOCKING MECHANISM IS PROVIDED IN THE POSITIONS.

PERPENDICULAR AND 90° LEFT/RIGHT

1. THE MODEL-527 IS A BOLSTER EXTENSION WHICH OUTWARD, SEE ILLUSTRATION ON SHEET 2 2. THE BOLSTER EXTENSIONS CAN SWING INWARD AND EXTENSION.

USUALLY REFERRED TO AS A SWING-AWAY BOLSTER IS PERMANENTLY MOUNTED TO THE PRESS. IT IS

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
527
CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld. 527
(NOTES CONTINUED ON PAGE 2)
PULL FORWARD TO UNLOCK
LOCKING MECHANISM LEVER (SPRING RETURN TO LOCK)

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

2" THICK SPACER ASS'Y (PART# 6580)

(MODEL 527-20)

(MODEL 527-18)

SPRING LOADED DIE STOP

527

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

RECOMMENDED

5. WHEN INWARD SWING IS DESIRED A 2" OR 4" SPACER SPACER BEHIND THE MOUNTING BRACKET. A MODEL-527-20 AND A MODEL-527-18 WITH A

THE SPACER IS NOT NECESSARY AND TWO BOLSTER ON TOP. WHEN OUTWARD SWING ONLY IS SPECIFIED IS PROVIDED. THE SPACER ALSO HAS A ROLLER

6. THIS TOP VIEW ILLUSTRATION IS TO SCALE SHOWING SEE CHART FOR MINIMUM CENTERLINE SPACING TO ALLOW BOLSTER EXTENSIONS TO SWING IN.

EXTENSIONS OF THE SAME LENGTH ARE PROVIDED. IN VARIOUS LENGTHS SHOWN IN TABLE ON SHEET 1.

4. THE BOLSTER EXTENSIONS ARE RATED AT 6000

DIE WEIGHT CAPACITY/PAIR. THEY ARE AVAILABLE

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
EXTENSION
PAGE 2 OF 2 REV -
MODEL 527 BOLSTER
EDGE OF BOLSTER ADJUSTABLE ROLLER 5.94 TYP. 2.47 5.23 20.41 22.52 DIM "X" 1.50 RAIL PAIR 24 32 40 18 20 28 LONG SHORT 22 28 36 16 18 24
MINIMUM CENTERLINE SPACING (X) 27.25 35.25 43.25 21.25 23.25 31.25 SPACER THICKNESS 2" 4" 4" 2" 2" 4" SPACER MODEL 7374 14688 14689 6580 6580 14688

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

3.

.656Ø TAP DRILL X 1.62 DP MIN

MAX LOAD: 3,000 LBS/ARM 1.

NOTES:UNLESS OTHERWISE SPECIFIED IDENTIFY WITH LABELS ON EACH ARM.

BOLSTER AT INSTALLATION. 2.

.375Ø HOLES TO BE MATCH DRILLED TAP 3/4-10UNC X 1.43 DP MIN IN FINAL ALIGNMENT AND MOUNTING OF AT INSTALLATION FOR ITEM 5 AFTER

SCREW, SHC, 3/4-10 X 2.25 ROLL PIN, .375Ø X 2.75 ROLL PIN, .187Ø X 1.50 HINGE PIN, 1.00Ø

ARM ASSY, 16" HINGE WELDMENT

MODEL 527-16 16” BOLSTER EXTENSION

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
6113 PAGE 1 OF 2 REV1 1 1 2 2 1 1 4 3 4 5 6 7 4
5309-100 6134
1644-36 1607-44 1674-24 4988 5614-6
QTY PART NUMBER DESCRIPTION ITEM
TEMPLTE, DRILL
1 REF 5 MARKED B 4 PLCS REF MARKED A 2 PLCS 6 .240 BRACKET.
SUPPLY ONE TEMPLATE PER SHIPMENT, HINGE SUBASSY VIEW B-B 5.94 TOP OF ROLLERS ON BOLSTER EXTENSION B A 3.438 B 1.719 1.250 A 3.938 B B 7.20
4.

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
MODEL 527-16 16” BOLSTER EXTENSION 6113 PAGE 2 OF 2 REV -
2 PLCS 4 PLCS 5 6 B SEE SH 1 2 4 3 16.00 (USE LOCKTITE) APPLY MAGNALUBE-G ALONG CONTACT SURFACES 1
B

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

MAX LOAD: 3,000 LBS/ARM INTO BOLSTER AT INSTALLATION

3.

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

.656Ø TAP DRILL x 1.62 DEEP MIN. IDENTIFY WITH LABELS EACH ARM AT INSTALLATION FOR ITEM 5 AFTER

2.

.375Ø HOLES TO BE MATCH DRILLED

FINAL ALIGNMENT AND MOUNTING OF NOTES: UNLESS OTHERWISE SPECIFIED BRACKET TAP 3/4-10 UNC x 1.43 DEEP MIN.

1.

SCREW, SHC, 3/4-10 x 2.25 HINGE PIN, 1.00Ø TEMPLATE, DRILL (REF.) ARM ASSY, 18" HINGE WELDMENT ROLL PIN, .187Ø x 1.50 ROLL PIN, .375Ø x 2.75

MODEL 527-18 18” BOLSTER EXTENSION 6527

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
PAGE 1 OF 2 REVSEE SH 1 B 5 2 PLCS MARKED A 4 PLCS MARKED B 6 REF 1 REF 7.20 .200 B A 1.250 1.719 TOP OF ROLLERS ON B BOLSTER EXTENSION B A B 3.438 5.94 3.938
PART NUMBER QTY DESCRIPTION ITEM
5309-100 6526 1674-24 5614-6 1607-44 1644-36 4988 1 4 2 2 1 4 3 7 6 5 1 1 1 0
VIEW B-B HINGE SUBASS'Y

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
527-18 18” BOLSTER EXTENSION 6527 PAGE 2 OF 2 REV1 4 PLCS 6
SH 1 18.00 3 2 PLCS 5 4 2
HINGE SUBASS'Y PART NUMBER QTY DESCRIPTION ITEM ARM ASSY, 18" HINGE WELDMENT 5309-100 6526 1 2 1 1
MODEL
SEE
B B VIEW B-B

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

REV -

MIN.

DRILL x 1.62 DEEP

.375Ø HOLES TO BE MATCH DRILLED AT INSTALLATION FOR ITEM 5 AFTER IDENTIFY WITH LABELS EACH ARM INTO BOLSTER AT INSTALLATION

SCREW, SHC, 3/4-10 x 2.25 ROLL PIN, .375Ø x 2.75

TEMPLTE, DRILL (REF.) ARM ASSY, 20" HINGE WELDMENT HINGE PIN, 1.00Ø ROLL PIN, .187Ø x 1.50

1644-36 1607-44 5614-6 5309-100 1674-24 4997 4988 PART NUMBER QTY ITEM DESCRIPTION 2 1 4 1 1 1 5 6 7 1 2 3 4 0

MODEL 527-20 20” BOLSTER EXTENSION PAGE 1 OF 2

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld. 5308
TAP
MAX LOAD:
TAP 3/4-10 UNC
MIN. BRACKET MARKED B 4 PLCS MARKED A 2 PLCS 6 REF REF 5 TOP OF ROLLERS ON B A B 7.20 1 .200 BOLSTER EXTENSION B A B 1.719 1.250 5.94 3.938 3.438
NOTES: UNLESS OTHERWISE SPECIFIED FINAL ALIGNMENT AND MOUNTING OF
1.
2. .656Ø
3.
3,000 LBS/ARM
x 1.43 DEEP
HINGE SUBASS'Y B
VIEW B-B

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
MODEL 527-20 20” BOLSTER EXTENSION 5308 PAGE 2 OF 2 REVPART NUMBER QTY ITEM DESCRIPTION HINGE SUBASS'Y B 4 PLCS 6 SEE SH 1 3 B 2 PLCS 5 4 2 1 LOCKING MECHANISM LATCH 20.00

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

5.

ITEM

MODEL

527-22 22” BOLSTER EXTENSION

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
14667 PAGE 1 OF 2 REV2.75 REF 5.156 5 MARKED B 4 PLACES 2 6 3.938 5.94 REF 2 PLACES MARKED A REF 1 1.719 1.250
ROLLERS
BOLSTER EXTENSION .185 4 AT INSTALLATION
B A A B
BOLSTER
SHIP
HOLES
DRILLED
TAP DRILL
1.62 DEEP MIN.
MAX LOAD:
B B TAP 3/4-10 UNC
1.43 DEEP MIN. IDENTIFY
LABEL
EACH ARM.
BOLSTER
CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld. INSTALLATION.
TOP OF
ON
FOR
5 AFTER ALSO BE USED TO FACILITATE DRILLING. BRACKET. ITEM 7 DRILLING TEMPLATE MAY FINAL ALIGNMENT AND MOUNTING OF NOTES: UNLESS OTHERWISE SPECIFIED
EXTENSION RATED 3,000 LBS EACH. 4.
ONE DRILL TEMPLATE PER LOT. 1. .375Ø
TO BE MATCH
2. .656Ø
x
3.
3,000 LBS/ARM
x
WITH
ON
IN
AT

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

22.0 REF

NOTE: THIS VIEW IS NOT TO SCALE

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
14667 PAGE 2 OF 2 REVSEE SHT 1
6 5 4 PLCS 2 PLCS 1
MODEL 527-22 22” BOLSTER EXTENSION
B B
4 3 2

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

5. BOLSTER EXTENSION RATED 3,000LBS EACH.

4. SHIP ONE DRILL TEMPLATE PER LOT.

2. .656Ø TAP DRILL X 1.62 DP MIN

1. .375Ø HOLES TO BE MATCH DRILLED

AT INSTALLATION FOR ITEM 5 AFTER ALSO BE USED TO FACILITATE DRILLING. BRACKET. ITEM 7 DRILLING TEMPLATE MAY FINAL ALIGNMENT AND MOUNTING OF NOTES:UNLESS OTHERWISE SPECIFIED

SCREW, SHC, 3/4-10 X 2.25 ROLL PIN, .375Ø X 2.75 ROLL PIN, .187Ø X 1.50 TEMPLATE, DRILLING ARM ASSY, 24" HINGE PIN, 1.00Ø HINGE, PREROLLER

MODEL 527-24 24” BOLSTER EXTENSION 5602

B

1644-36 1607-44 1674-24 5316-100 5614-8 5123 5630

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
PAGE 1 OF 2 REV -
2.75 REF 5.156 5 MARKED B 4 PLCS 2 6 3.938 5.94 B A A B REF 2 PLCS MARKED A REF 1 1.719 1.250 TOP OF ROLLERS ON BOLSTER EXTENSION B B .185
CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld. FROM SHEET
VIEW B-B
2 HINGE SUBASSY
PART NUMBER QTY DESCRIPTION ITEM 4 2 1 1 1 1 4 1 2 3 4 5 6 7
3. MAX LOAD: 3,000 LBS/ARM TAP 3/4-10UNC X 1.43 DP MIN IN IDENTIFY WITH LABEL ON EACH ARM. BOLSTER AT INSTALLATION.

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

B 24.00REF

MODEL 4 3 2

1 TOP OF ROLLERS ON BOLSTER EXTENSION .185

5. BOLSTER EXTENSION RATED 3,000LBS EACH. 4. SHIP ONE DRILL TEMPLATE PER LOT. 3. MAX LOAD: 3,000 LBS/ARM

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
527-24 24” BOLSTER EXTENSION 5602 PAGE 2 OF 2 REVSEE SH 1
CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld. B 6 5 4 PLCS 2 PLCS

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

BCONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

MAX LOAD: 3,000 LBS/ARM IDENTIFY WITH LABEL ON EACH ARM.

3.

.656Ø TAP DRILL X 1.62 DP MIN TAP 3/4-10UNC X 1.43 DP MIN IN BOLSTER AT INSTALLATION.

.375Ø HOLES TO BE MATCH DRILLED AT INSTALLATION FOR ITEM 5 AFTER FINAL ALIGNMENT AND MOUNTING OF

2.

1.

NOTES: UNLESS OTHERWISE SPECIFIED

TEMPLATE, DRILL

PER SHIPMENT. ITEM 4 2 1 1 1 1

SUPPLY ONE TEMPLATE DESCRIPTION PART NUMBER

BRACKET ARM ASSY, 28" SCREW, SHC, 3/4-10 X 2.25 ROLL PIN, .375Ø X 2.75 ROLL PIN, .187Ø X 1.50 HINGE PIN, 1.00Ø HINGE, PREROLLER 1 2 3 4 5 6 7 4

MODEL 527-28 28” BOLSTER EXTENSION 5974

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
PAGE 1 OF 2 REV -
FROM SHEET 2 VIEW
HINGE SUBASSY 1.719 B 3.938 5.94 B A 5.156 1.250 2 .182 B 5 REF 2 PLCS MARKED A MARKED B 4 PLCS REF 6 A B
OF ROLLERS ON BOLSTER EXTENSION
B-B
TOP
1
1644-36 1607-44 1674-24 5123 5316-100 5981 5614-8
4. QTY

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
MODEL 527-28 28” BOLSTER EXTENSION 5974 PAGE 2 OF 2 REV6 5 4 PLCS 2 PLCS
SEE SH 1 4 3 2 28.00 REF
1 TOP OF ROLLERS ON BOLSTER EXTENSION
B
B

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

MAX LOAD: 3,000 LBS/ARM

3.

IDENTIFY WITH LABEL EACH ARM.

.656Ø TAP DRILL X 1.62 DP MIN

NOTES:UNLESS OTHERWISE SPECIFIED BOLSTER AT INSTALLATION. TAP 3/4-10UNC X 1.43 DP MIN IN

HINGE, PREROLLER HINGE PIN, 1.00Ø ROLL PIN, .187Ø X 1.50 ROLL PIN, .375Ø X 2.75 SCREW, SHC, 3/4-10 X 2.25

MODEL 527-32 32” BOLSTER EXTENSION 5315

ARM ASSY, 32"

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

VIEW B-B

HINGE SUBASSY FROM SHEET 2

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
PAGE 1 OF 2 REVB 7 6 5 4 3 2 1
5122 5316-100 5123 1674-24 1607-44 1644-36
1. .375Ø
MATCH DRILLED BRACKET 1.719 3.938 5.94 5.156 1.250 .200 REF 2 PLCS MARKED A MARKED B 4 PLCS REF TOP OF ROLLERS ON BOLSTER EXTENSION 5614-8 TEMPLATE, DRILL
SUPPLY ONE TEMPLATE PER SHIPMENT. DESCRIPTION PART NUMBER ITEM 4 1 1 1 1 2 4 QTY B B A 2 B 5 6 1 A B
2.
FINAL ALIGNMENT AND MOUNTING OF AT INSTALLATION FOR ITEM 5 AFTER
HOLES TO BE
4.

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

MODEL

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
527-32 32” BOLSTER EXTENSION 5315 PAGE 2 OF 2 REVB 1 2 PLCS 4 PLCS 2 SEE SH 1 5 6 B 3 4 32.00 REF IDENTIFY WITH LABEL EACH ARM. 3. MAX LOAD: 3,000 LBS/ARM TAP 3/4-10UNC X 1.43 DP MIN IN 2. .656Ø TAP DRILL X 1.62 DP MIN 1.250 .200 TOP OF ROLLERS ON BOLSTER EXTENSION 4. SUPPLY ONE TEMPLATE PER SHIPMENT.

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

.656Ø TAP DRILL x 1.62 DEEP MIN. TAP 3/4-10 UNC x 1.43 DEEP MIN. IN BOLSTER AT INSTALLATION.

2.

HOLES TO BE MATCH DRILLED AT INSTALLATION FOR ITEM 5 AFTER FINAL ALIGNMENT AND MOUNTING OF BRACKET

.375Ø

1.

A A BACK VIEW

NOTES: UNLESS OTHERWISE SPECIFIED

REF 2 PLACES MARKED "A" 5

MAX LOAD: 3,000 LBS/ARM IDENTIFY WITH LABEL EACH ARM. 0.18 NOMINAL REF 4 PLACES MARKED "B" 6 TOP OF ROLLERS ON BOLSTER EXTENSION

1 3.938 5.94

B B

SCREW, SHC, 3/4-10 x 2.25 ROLL PIN, .187Ø x 1.50 HINGE PIN, 1.00Ø ARM ASS'Y, 36" HINGE, PREROLLER, 10" ROLL PIN, .375Ø x 2.75 1674-24 5288 5321-100 5588 1644-36 1607-44

B B FROM SHEET 2 VIEW B-B HINGE SUBASS'Y

1 2 3 4 5 6 ITEM B SEE SHT 1

MODEL 527-36 36” BOLSTER EXTENSION

36" REF. 3

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
PAGE 1 OF 2 REV1 1 1 1 2 4
5338
QTY DESCRIPTION
PART NUMBER
3. 1.403 1.565 7.276

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
MODEL 527-36 36” BOLSTER EXTENSION 5338 PAGE 2 OF 2 REV1 1 ARM ASS'Y, 36" HINGE, PREROLLER, 10" 5321-100 5588 QTY DESCRIPTION PART NUMBER 3.938 5.94 FROM SHEET 2 VIEW B-B HINGE SUBASS'Y B SEE SHT 1 1 36" REF. 4 PLCS 2 4 6 2 PLCS 5 3 B

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

MAX LOAD: 3,000 LBS./ARM

REV -

MODEL PAGE 1 OF 2

.656Ø TAP DRILL x 1.62 DEEP MIN. FINAL ALIGNMENT AND MOUNTING OF AT INSTALLATION FOR ITEM 5 AFTER

.375Ø HOLES TO BE MATCH DRILLED

IDENTIFY WITH LABEL EACH ARM. IN BOLSTER AT INSTALLATION. TAP 3/4-10 UNC x 1.43 DEEP MIN. BRACKET

2.

1.

NOTES: UNLESS OTHERWISE SPECIFIED

SCREW, SHC, 3/4-10 x 2.25 ROLL PIN, .375Ø x 2.75 HINGE, PREROLLER, 10" ARM ASS'Y, 40" HINGE PIN, 1.00Ø ROLL PIN, .187Ø x 1.50

1607-44 1644-36 5295 5321-100 5288 1674-24 QTY PART NUMBER DESCRIPTION ITEM 1 6 5 4 3 2 1 1 1 1 2 4

B B REF 4 PLACES MARKED "B" 6 B B REF 2 PLACES MARKED "A" 5 1 A A 0.18 NOMINAL TOP OF ROLLERS ON BOLSTER EXTENSION FROM SHEET 2 VIEW B-B HINGE SUBASS'Y 1.403 1.565 7.276 3.938 5.94 SEE SHT 1 B

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld. 527-40 40” BOLSTER EXTENSION 5320
3.

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it sho uld be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com
MODEL 527-40 40” BOLSTER EXTENSION 5320 PAGE 2 OF 2 REVHINGE, PREROLLER, 10" ARM ASS'Y, 40" HINGE PIN, 1.00Ø 5295 5321-100 5288 QTY PART NUMBER DESCRIPTION ITEM 1 3 2 1 1 1 FROM SHEET 2 VIEW B-B HINGE SUBASS'Y 3.938 5.94 2 PLCS SEE SHT 1 B 1 3 2 6 5 4 PLCS 4 B 40" REF.
N118 W18251 Bunsen Drive Germantown,WI 53022 (262) 250-4410 • Fax (262) 250-4409 pfa-inc.com

Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.