PFA DR-317/318 Model 317 & 318 Hydraulic Die Lifter Rail

Page 1

MODEL 317 & 318 HYDRAULIC DIE LIFTER RAIL

N118 W18251 Bunsen Drive Germantown,WI 53022 (262) 250-4410 • Fax (262) 250-4409

pfa-inc.com Copyright Š2020 PFA, Inc. All rights reserved. Reproduction or use in any manner of editorial or graphic content herein without the express written permission of PFA, Inc. is strictly prohibited. Every effort has been made to ensure the information within this publication is complete and accurate at the time of printing.

S3104 DR-317/318 REV A - 2/20



TABLE OF CONTENTS 1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4. Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5. Recommended Spare Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6. Drawing 317N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7. Drawing 317W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8. Drawing 318N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 9. Drawing 318W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 10. Drawing Slots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

pfa-inc.com MODEL 317 & 318 | HYDRAULIC DIE LIFTER RAIL | PAGE 3


INTRODUCTION NOTE: This User Guide is written for the knowledgeable mechanic. 1. Both Models DR-317 and DR-318 have a common single inline cam roller configuration. 2. The Model DR-317 has a rectangular cross section and the Model DR-318 has a T-shaped cross section. 3. The Model DR-317 Die Lifter is the more universal model, as it may be mounted in either a T-slot or Rectangular slot. 4. The Model DR-318 Die Lifter is more limiting, as it must be mounted in a T-slot only. 5. Typical Wide Slots are 1” (1.060”) and Narrow Slots are 3/4” (.812”) which provide room on the sides for easy movement for nominal rail widths - Narrow (N) .800” or Wide (W) .995”. See SLOTS drawing for details on T-slot and Rectangular (U-slot) configurations. 6. Both are available in High Profile (HP) and Low Profile (LP) versions to accommodate a range of slot heights. Some sizes may be available in Extremely Low Profile (ELP) versions.

NOTE: The Model 317 and Model 318 are similar, except for rail body shape. 7. Lift height is controlled by custom piston strokes for rectangular rails and custom T or tab height for T shaped rails. Part numbers state tab or stroke, neck width, profile, and bracket types, as appropriate. 8. Movement: When hydraulic pressure is applied to the die lifter, downward facing pistons extend causing the die lifter to elevate. When the hydraulic pressure is turned off, the weight of the die will cause the die lifter to recess. 9. 317N and 318N Lift Capacity: Maximum die weight per pair is 1,800 lbs per foot of die contact. For example a 36 inch die resting on a pair of 48” die lifters must not exceed 5,400 lbs. [36” = 3 ft x 1,800 lbs/ft = 5,400 lbs] 10. 317W and 318W Lift Capacity: Maximum die weight per pair is 2,150 lbs per foot of die contact. For example a 36 inch die resting on a pair of 48” die lifters must not exceed 6,450 lbs. [36” = 3 ft x 2,150 lbs/ft = 6,450 lbs] 11. Please study drawings 317N, 317W, 318N and 318W, as appropriate.

pfa-inc.com MODEL 317 & 318 | HYDRAULIC DIE LIFTER RAIL | PAGE 4


INSTALLATION 1. Place the die lifter in the bolster T-slot and check for proper fit. A rectangular slot may be used for the Model 317. The bolster slot needs to be wide enough for unhampered up and down articulation. Also, remove any foreign material in the slot. 2. Check bolster slot for proper depth. When hydraulic pressure is applied the die lifter roller balls should be above the bolster surface by the amount requested at the time of order. Typically lift above surface ranges from .060� to .125� above the bolster surface. In the lowered position, the die lifter roller balls must be below the bolster surface. If existing bolster extensions (pre-rollers) are installed, the die lifter roller balls, when elevated, must be on the same plane with the extensions for a smooth transition. If bolster slot is too deep, a spacer may be placed on the bottom for height adjustment. 3. A end mounting bracket (EBK) on the end of the die lifter rail is often used to keep the die lifter from moving horizontally. An internal to slot bracket (IB) and extension fitting is also available to prevent movement, allowing rails to be centered in the slot for certain applications. 4. For end mounting brackets, please refer to enclosed drawings to drill and tap the 1/4-20 UNC holes in the bolster for mounting the bracket guides. Place the rail centered in the T-slot with the mounting bracket touching the side of the bolster. Make sure that the pistons are recessed. With the mounting bracket as a reference mark the drill point on each side of the mounting bracket using the left/right dimensions shown on drawings.

CAUTION: MAKE SURE THAT THE MOUNTING BRACKET IS RETAINED BY THE SCREWS WHEN THE DIE LIFTER IS IN THE FULL DOWN POSITION AND THAT THE DIE LIFTER IS FREE TO MOVE UP AND DOWN. 5. Secure the mounting bracket using the two screws furnished. Make sure the guide sleeve is placed over the screw prior to installation. 6. After proper positioning of the die lifters, attach the hydraulic hoses. In most cases, the die lifter circuit on PFA Power and Control Module provides the control and hydraulic pressure to operate the die lifters. 7. The die lifters are tested at the factory. Some hydraulic fluid will remain and minimize the amount of air in the die lifter. However, before using the die lifters make sure that the air is purged from the lines by repeatedly pressurizing and depressurizing the die lifters.

CAUTION: WHEN INSTALLING ANY HYDRAULIC EQUIPMENT TAKE CARE TO PREVENT ANY CONTAMINATION FROM ENTERING HYDRAULIC LINES. DO NOT USE BLACK PIPE TO CARRY HYDRAULIC FLUID.

pfa-inc.com MODEL 317 & 318 | HYDRAULIC DIE LIFTER RAIL | PAGE 5


OPERATION Please integrate the following steps into your approved QDC procedures. 1. Remove die clamps and make sure that the ram is away from the die. 2. Elevate die lifters by applying hydraulic pressure. 3. Roll die off bolster. 4. Roll next die onto bolster and make positioning adjustments. 5. Lower die lifters by turning off hydraulic pressure. 6. Clamp die.

CAUTION: MAKE SURE DIE LIFTER IS IN THE DOWN POSITION BEFORE CLAMPS ARE APPLIED.

pfa-inc.com MODEL 317 & 318 | HYDRAULIC DIE LIFTER RAIL | PAGE 6


MAINTENANCE 1. Should it become necessary to replace ball cartridges, hydraulic seals or pistons follow the steps listed below carefully and refer to illustration D1 and referenced (item) numbers in the spare parts section. 2. To replace a damaged ball cartridge remove the die lifter from the press and place the die lifter rail on a suitable work surface. Remove the steel retaining ring(s) and affected ball cartridge(s). Replace with new.

NOTE: Spring washer at the bottom of the ball cartridge cavity is replaced cone up. 3. To replace a piston or lower piston seal do the following: a. Remove the SAE hex face plug, which covers the affected cylinder. (Replace it if necessary during reassembly). b. Turn the rail over (rollers down) and push the piston out carefully using a blunt pointed tool. Do not scratch cylinder wall. c. Replace the internal o-ring. d. Reassemble in reverse.

NOTE: If the piston for some very unusual reason has mushroomed on the underside of the rail it will be necessary to remove the enlarged diameter before attempting to push it out of the cylinder. In such a case push the piston all the way out from above and use a saw, file or other tool to cut off the enlarged area. Deburr the cut off end before pushing the piston out. 4. If the die lifter is assembled using two segments they may be separated as follows: a. Refer to illustration D-1 and remove two screws on one end of the plate which secure the two segments. b. Drive out both roll pins which secure the splice on top of the die lifter. c. Separate the two halves by pulling apart. Do not bend. d. O’rings and backup rings can now be replaced on the pipe connecting the two segments. Use an O’ring lubricant. e. Re-assemble carefully in reverse sequence. PLUG

SPLICE PLATE TOP

BALL CARTRIDGE

SCREW RETAINING RING

BELLEVILLE WASHER

O-RING

pfa-inc.com SCREW

PISTON

SPLICE PLATE BOTTOM

CONNECTING TUBE

MODEL 317 & 318 | HYDRAULIC DIE LIFTER RAIL | PAGE 7


RECOMMENDED SPARE PARTS 317N OR 318N (NARROW) RAILS – LP (LOW PROFILE) P/N

Description

7120-XXX

Piston (specific to rail part number)

Qty 6

1783-012

Poly O’ring

6

2517

Ball Cage Assy

6

6710

Spring, Disc

6

1788-4

Plug

6

6736-68

Retaining Ring

6

6353 (6868 317N Only)

Bracket Assembly

1

317N OR 318N (NARROW) RAILS – HP (HIGH PROFILE) P/N

Description

Qty

7068-XXX

Piston (specific to rail part number)

6

1783-012

Poly O’ring

6

2517

Ball Cage Assy

6

6710

Spring, Disc

6

1788-4

Plug

6

6736-68

Retaining Ring

6

6353 (6868 317N Only)

Bracket Assembly

1

317W OR 318W (WIDE) RAILS – LP (LOW PROFILE) P/N

Description

Qty

7120-XXX

Piston (specific to rail part number)

6

1783-012

Poly O’ring

6

2513

Ball Cage Assy

6

6735

Spring, Disc

6

1788-4

Plug

6

6736-93

Retaining Ring

6

6353

Bracket Assembly

1

317W OR 318W (WIDE) RAILS – HP (HIGH PROFILE) P/N

Description

Qty

7068-XXX

Piston (specific to rail part number)

6

1783-012

Poly O’ring

6

2513

Ball Cage Assy

6

6735

Spring, Disc

6

1788-4

Plug

6

6736-93

Retaining Ring

6

6353

Bracket Assembly

1

pfa-inc.com MODEL 317 & 318 | HYDRAULIC DIE LIFTER RAIL | PAGE 8


CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

MODEL# 317N-12 317N-19 317N-22 317N-24 317N-26 317N-29 317N-31 317N-33

DIM 'A'

2 MAX. DIE WEIGHT/PAIR

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it should be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

# BALLS PER RAIL

12 1,800 LBS 10 19 2,800 LBS 16 22 3,300 LBS 18 24 3,600 LBS 20 26 3,900 LBS 22 29 4,300 LBS 24 31 4,600 LBS 26 33 4,900 LBS 28 SEE CATALOG FOR OTHER AVAILABLE SIZES

# PISTONS PER RAIL 2 3 4 4 4 5 5 5

A

1 .800

0.50 FOR LOW PROFILE RAILS, 0.75 FOR HIGH PROFILE RAILS

2.120

2.120

1.485 (LP) 1.720 (HP)

MOUNTING BRACKET

4 1/4-20 UNC x .50 DEEP THREAD, (2) PLACES

4 3

2 1

1.77

3

THIS DIE LIFTER IS AVAILABLE IN LOW PROFILE (LP) AND HIGH PROFILE (HP). IF T-SLOTS ARE TOO DEEP ADD SPACERS/SHIMS AS NECESSARY. DIMENSION IS FROM BOTTOM OF RAIL TO TOP OF ROLLERS. EACH DIE LIFTER IS DESIGNED TO ELEVATE THE ROLLER BALLS .080 ABOVE THE BOLSTER SURFACE (THE HYDRAULIC PISTONS ARE MACHINED TO ELEVATE THE RAIL UNTIL THIS .080 ELEVATION IS REACHED). SPECIFY OTHER DESIRED ELEVATION OR SHIM AS NECESSARY. MAX DIE WEIGHT PER PAIR IS AT 5,000 PSI. HYDRAULIC PRESSURE, RATED @150 LBS. PER INCH OF DIE CONTACT. FOR EXAMPLE, A 25" DIE RESTING ON A PAIR OF DIE LIFTERS 33" LONG MUST NOT EXCEED 3750 LBS. LENGTHS SHOWN ARE TYPICAL, OTHER LENGTHS AVAILABLE. MODELS LONGER THAN 48" ARE MADE IN TWO OR MORE SECTIONS, USING A STAINLESS STEEL SPLICE PLATE FOR A RIGID CONNECTION.

.38 MAXIMUM PISTON TRAVEL, LP RAIL (.407 REF.) .62 MAXIMUM PISTON TRAVEL, HP RAIL (.640 REF.)

THE MODEL-317 DIE LIFTER HAS A RECTANGULAR CROSS SECTION, BALL TYPE ROLLERS AND IS HYDRAULICALLY ACTUATED AT 5,000 PSI. MAX. THIS DRAWING SHOWS A NARROW (N) MODEL 317 DIE LIFTER. REFER TO DWG 317W FOR WIDE (W).

MODEL 317 HYDRAULIC DIE LIFTER RAIL 317N

PAGE 1 OF 1

REV -

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com


CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

MODEL# 317W-14 317W-19 317W-24 317W-29 317W-34 317W-39 317W-44 317W-48 317W-53 317W-58 317W-63 317W-68 317W-73

DIM # BALLS # PISTONS 2 MAX DIE 'A' PER RAIL PER RAIL WEIGHT/PAIR 14 2,500 LBS 10 3 19 3,400 LBS 14 4 24 4,300 LBS 18 5 29 5,200 LBS 22 6 34 6,100 LBS 26 7 39 7,000 LBS 30 8 44 7,900 LBS 34 9 48 8,600 LBS 36 10 53 9,500 LBS 40 11 58 10,400 LBS 44 12 63 11,300 LBS 48 13 68 12,200 LBS 52 14 73 13,100 LBS 56 15 SEE CATALOG FOR OTHER AVAILABLE SIZES

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it should be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

RIGID SPLICE N N N N N N N N Y Y Y Y Y

A

1 .995

0.50 FOR LOW PROFILE RAILS, 0.75 FOR HIGH PROFILE RAILS

2.120

2.120 1.485 (LP) 1.720 (HP)

MOUNTING BRACKET

4 1/4-20 UNC x .50 DEEP THREAD, (2) PLACES

1.77

3

4

THIS DIE LIFTER IS AVAILABLE IN LOW PROFILE (LP) AND HIGH PROFILE (HP). IF SLOTS ARE TOO DEEP ADD SPACERS/SHIMS AS NECESSARY. DIMENSION IS FROM BOTTOM OF RAIL TO TOP OF ROLLERS.

3

EACH DIE LIFTER IS DESIGNED TO ELEVATE THE ROLLER BALLS .080 ABOVE THE BOLSTER SURFACE (THE HYDRAULIC PISTONS ARE MACHINED TO ELEVATE THE RAIL UNTIL THIS .080 ELEVATION IS REACHED). SPECIFY OTHER DESIRED ELEVATION OR SHIM AS NECESSARY.

2

MAX DIE WEIGHT PER PAIR IS AT 5,000 PSI HYDRAULIC PRESSURE, RATED @180 LBS. PER INCH OF DIE CONTACT. FOR EXAMPLE, A 30" DIE RESTING ON A PAIR OF DIE LIFTERS 48" LONG MUST NOT EXCEED 5,400 LBS.

1

LENGTHS SHOWN ARE TYPICAL, OTHER LENGTHS AVAILABLE. MODELS LONGER THAN 48" ARE MADE IN TWO OR MORE SECTIONS, USING A STAINLESS STEEL SPLICE PLATE FOR A RIGID CONNECTION.

.36 MAXIMUM PISTON TRAVEL, LP RAIL (.385 REF.) .58 MAXIMUM PISTON TRAVEL, HP RAIL (.600 REF.) THE MODEL-317 DIE LIFTER HAS A RECTANGULAR CROSS SECTION, BALL TYPE ROLLERS AND IS HYDRAULICALLY ACTUATED AT 5,000 PSI. THIS DRAWING SHOWS A WIDE (W) MODEL 317 DIE LIFTER. REFER TO DWG 317N FOR NARROW (N).

MODEL 317 HYDRAULIC DIE LIFTER RAIL 317W

PAGE 1 OF 1

REV -

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com


CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

MODEL# 318N-12 318N-19 318N-22 318N-24 318N-26 318N-29 318N-31 318N-33

# BALLS 2 MAX DIE PER RAIL WEIGHT/PAIR 12 1,800 LBS 10 19 2,800 LBS 16 22 3,300 LBS 18 24 3,600 LBS 20 26 3,900 LBS 22 29 4,300 LBS 24 31 4,600 LBS 26 33 4,900 LBS 28 SEE CATALOG FOR OTHER AVAILABLE SIZES DIM 'A'

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it should be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

# PISTONS PER RAIL 2 3 4 4 4 5 5 5

A

1 .800

0.50 FOR LOW PROFILE RAILS, 0.75 FOR HIGH PROFILE RAILS

1.38

2.120

2.120

5

1.485 (LP) 1.720 (HP)

MOUNTING BRACKET

4 1/4-20 UNC x .50 DEEP THREAD, (2) PLACES

5

1.77

3

.38 MAXIMUM PISTON TRAVEL, LP RAIL (.407 REF.) .62 MAXIMUM PISTON TRAVEL, HP RAIL (.640 REF.)

RAIL 1.50 WIDE MAY BE SUBSTITUTED IF T-SLOT IS WIDE ENOUGH.

4

THIS DIE LIFTER IS AVAILABLE IN LOW PROFILE (LP) AND HIGH PROFILE (HP). IF T-SLOTS ARE TOO DEEP ADD SPACERS/SHIMS AS NECESSARY. DIMENSION IS FROM BOTTOM OF RAIL TO TOP OF ROLLERS.

3

FLANGE THICKNESS IS MACHINED TO FIT CUSTOMERS' T-SLOTS AND POSITION ELEVATED BALL ROLLERS .080 ABOVE BOLSTER SURFACE. OTHER ELEVATIONS ABOVE THE BOLSTER MAY BE SPECIFIED.

2

MAX DIE WEIGHT PER PAIR IS AT 5,000 PSI. HYDRAULIC PRESSURE, RATED @150 LBS. PER PER INCH OF DIE CONTACT. FOR EXAMPLE, A 25" DIE RESTING ON A PAIR OF DIE LIFTERS 33" LONG MUST NOT EXCEED 3750 LBS.

1

LENGTHS SHOWN ARE TYPICAL, OTHER LENGTHS AVAILABLE. MODELS LONGER THAN 48" ARE MADE IN TWO OR MORE SECTIONS, USING A STAINLESS STEEL SPLICE PLATE FOR A RIGID CONNECTION.

THE MODEL-318 DIE LIFTER HAS A T-PROFILE CROSS SECTION, BALL TYPE ROLLERS AND IS HYDRAULICALLY ACTUATED AT 5,000 PSI. THIS DRAWING SHOWS A NARROW (N) MODEL 318 DIE LIFTER. REFER TO DWG 318W FOR WIDE (W).

MODEL 318 HYDRAULIC DIE LIFTER RAIL 318N

PAGE 1 OF 1

REV -

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com


CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

MODEL# 318W-14 318W-19 318W-24 318W-29 318W-34 318W-39 318W-44 318W-48 318W-53 318W-58 318W-63 318W-68 318W-73

DIM # BALLS # PISTONS 2 MAX. DIE 'A' PER RAIL PER RAIL WEIGHT/PAIR 14 2,500 LBS 10 3 19 3,400 LBS 14 4 24 4,300 LBS 18 5 29 5,200 LBS 22 6 34 6,100 LBS 26 7 39 7,000 LBS 30 8 44 7,900 LBS 34 9 48 8,600 LBS 36 10 53 9,500 LBS 40 11 58 10,400 LBS 44 12 63 11,300 LBS 48 13 68 12,200 LBS 52 14 73 13,100 LBS 56 15 SEE CATALOG FOR OTHER AVAILABLE SIZES

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it should be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

RIGID SPLICE N N N N N N N N Y Y Y Y Y

A

1

0.50 FOR LOW PROFILE RAILS, 0.75 FOR HIGH PROFILE RAILS

.995

2.120

2.120

1.485 (LP) 1.720 (HP)

MOUNTNG BRACKET 1/4-20 UNC x .50 DEEP THREAD, (2) PLACES

4 3 2 1

1.50

4 1.77

3

THIS DIE LIFTER IS AVAILABLE IN LOW PROFILE (LP) AND HIGH PROFILE (HP). IF T-SLOTS ARE TOO DEEP ADD SPACER/SHIMS AS NECESSARY. DIMENSION IS FROM BOTTOM OF RAIL TO TOP OF ROLLERS. FLANGE THICKNESS IS MACHINED TO FIT CUSTOMERS' T-SLOTS AND POSITION ELEVATED BALL ROLLERS .080 ABOVE BOLSTER SURFACE. OTHER ELEVATIONS ABOVE THE BOLSTER MAY BE SPECIFIED. MAX DIE WEIGHT PER PAIR IS AT 5,000 PSI. HYDRAULIC PRESSURE, RATED @180 LBS. PER INCH OF DIE CONTACT. FOR EXAMPLE, A 30" DIE RESTING ON A PAIR OF DIE LIFTERS 48" LONG MUST NOT EXCEED 5,400 LBS. LENGTHS SHOWN ARE TYPICAL, OTHER LENGTHS AVAILABLE. MODELS LONGER THAN 48" ARE MADE IN TWO OR MORE SECTIONS, USING A STAINLESS STEEL SPLICE PLATE FOR A RIGID CONNECTION.

.36 MAXIMUM PISTON TRAVEL, LP RAIL (.385 REF.) .58 MAXIMUM PISTON TRAVEL, HP RAIL (.600 REF.) THE MODEL-318 DIE LIFTER HAS A T-PROFILE CROSS SECTION, BALL TYPE ROLLERS AND IS HYDRAULICALLY ACTUATED AT 5,000 PSI. MAX. THIS DRAWING SHOWS A WIDE (W) MODEL 318 DIE LIFTER. REFER TO DWG 318N FOR NARROW (N).

MODEL 318 HYDRAULIC DIE LIFTER RAIL 318W

PAGE 1 OF 1

REV -

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com


CONFIDENTIAL: The information shown on this sheet is confidential. Permission to use, reproduce or transmit in any way not specifically authorized is expressly withheld.

DISCLAIMER: Illustrative drawings, CAD models, and information described herein is proprietary intellectual property of PFA, Inc., accurate to the company’s knowledge at time of printing, and intended for reference only. Specifications are subject to change without notice. If the information obtained from this document is critical to a specific application, it should be confirmed by contacting PFA, Inc. PFA Terms of Sale apply.

U-SLOTS (RECTANGULAR)

'A'

'A'

T-SLOTS 'D'

NOMINAL SIZE

'E'

PRESS #

5

4 3

BOLSTER

'A' (±.010)

'E'

'E' (±.010)

3/4"

5 .840

1.510

1"

1.062

1.510

2"

2.030

2.200

'C' (REF)

.03

(ALLOWABLE) 'B'

2

WHEN MACHINING/REMACHINING 3/4" SLOTS USE .840 ±.010 FOR THE 'A' DIMENSION. THIS CREATES OPTIMUM FIT FOR THE DIE LIFTERS. (THE ANSI/ASME "A" DIM OF .812 WILL WORK AND DOES NOT NEED TO BE ENLARGED IN EXISTING SLOTS). THE T AND U SLOTS SHOWN ALLOW USE OF STANDARD PFA, INC. DIE LIFTERS, DIE CLAMPS AND ACCESSORIES. PFA, INC. PART NUMBERS FOR T-NUT SIZES ARE SHOWN. OTHER SIZES, INCLUDING SINGLE PIECE T-BOLTS ARE AVAILABLE.

2

THIS AREA MAY BE USED AS A WORKSHEET TO RECORD ACTUAL SLOT DIMENSIONS.

1

THIS IS A SELECTION OF T-SLOT SIZES WHICH CONFORM TO 'A' DIMENSIONS ESTABLISHED BY ASME B5.1M-1985, REAFFIRMED 2014. DIMENSIONS 'B', 'C' , 'D' AND 'E' ARE WITHIN MIN./MAX. ASME PARAMETERS.

NOMINAL T-BOLT SIZE

'A' (+.010 -.000)

'B' (+.03 -.00)

'C' (REF)

'D' (+.010 -.000)

'E' (±.010)

5/8"

.688

1.22

.50

.750

1.250

3/4"

.812

1.43

.63

.875

1.510

1.062

1.80

.80

1.000

1.805

1"

PRESS #

BOLSTER

PRESS #

RAM

1

2

*

*

* PLUS _______ CUTTER RELIEF, IF ANY. 'A' THREAD SIZE 'D' (REF) 'E' 'C'

'B'

T-NUT

3 PART#

SELECTED T-NUTS NOMINAL THREAD T-SIZE SIZE

'A'

'B'

'C'

'D' (REF)

'E'

1767-1

5/8"

5/8-11

.67

1.13

.42

.33

.75

1755-13

3/4"

3/4-10

.80

1.25

.56

.44

1.0

1755-16

1"

3/4-10

1.03

1.62

.63

.37

1.0

4983-16

1"

7/8-9

1.03

1.62

.69

.31

1.0

COMMON SLOTS T SHAPE & RECTANGULAR PAGE 1 OF 1

REV -

N118 W18251 Bunsen Drive, Germantown, WI 53022 | 262.250.4410 | pfa-inc.com


N118 W18251 Bunsen Drive Germantown,WI 53022 (262) 250-4410 • Fax (262) 250-4409

pfa-inc.com


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.