Vliv mikrostruktury na mechanické vlastnosti niklové superslitiny... J. Zýka – I. Andršová – J. Málek – B. Podhorná – A. Joch –K. Hrbáček 10
Tab. III. Mechanické vlastnosti a mikrostrukturní parametry odlitků ze slitiny MAR-M-247 Tab. III. Mechanical properties and microstructure parameters of different castings of the MAR-M-247 alloy
9
6
A [%]
velikost zrna [mm]
podíl vad na řezu [%]
podíl vad na lomu [%]
lehký
838
1202
11,0
0,298
0,004
0
0,537
střední
844
975
4,1
0,652
0,056
0,082
0,368
těžký
777
867
3,7
0,714
0,012
0,038
0,596
Deformation [%]
Rm [MPa]
Odlitek
7 5
y = 0,063x - 49,885 R² = 0,9831
4
MAR-light MAR-medium
3 2
MAR-heavy
1 0 800
1200
Obr. 3. 1000
Stress [MPa]
Fig. 3. 800 600
1000 1100 Stress [MPa]
1200
Deformační zpevnění zkušebních těles z různých odlitků ze slitiny MAR-M-247 Strain hardening of specimens from different MAR-M-247 castings
MAR-light MAR-medium
400
MAR-heavy
the centre as a result of directional solidification because of rapid cooling of the light castings. Equiaxial grains were found in specimens from the other types of castings. Investigation of metallographic sections and fractures shows low void fraction, but large amount of interdendritic carbides (fig. 4 and 5). Longer carbides are found at specimens’ microstructure from the heavy castings, with length up to 100 µm. Length of the carbide is reduced in specimen from the medium and the light castings.
200 0 0
Obr. 2. Fig. 2.
900
1
2
3
4 5 6 Deformation [%]
7
8
9
10
Tahový diagram zkušebních těles z různých odlitků ze slitiny MAR-M-247 Stress strain diagram of specimens from different MAR-M-247 castings
(a)
(a)
a)
a)
(b)
(b)
b)
b)
(c)
c)
(c)
c)
Obr. 4. Makrostruktura na leptaných podélných metalograficFigure 2 Macro etched longitudinal metallographic section of tensile test (left) and non-etched kých řezech (vlevo) a licí vady na neleptaných metalopictures of casting voids from heavy (a), medium (b) and light casting (c) - LM. grafických řezech (vpravo) z těžkého (a), středního (b) a lehkého (c) odlitku – LM Fig. 4. Macro etched longitudinal metallographic section of tensile test (left) and non-etched metallographic section with casting voids (right) from heavy (a), medium (b) and light casting (c)— LM
Obr. 5.
Neleptané podélné metalografické řezy s karbidy různých tvaru a velikostí – LM (vlevo) a prasklé karbidy na morphology-lomové LM (left) ploše and broken carbides on fracture surface (right) SEM from heavy(b) (a), (SEM) (vpravo) z těžkého (a), středního mediuma(b) and light casting (c) withsdifferent carbides size andvelikostí morphologylehkého (c) odlitku karbidy různých a LM tvarů Fig. 5. Non-etched longitudinal metallographic sections with different carbides size and morphology—LM (left) and broken carbides on fracture surface (right) SEM from heavy (a), medium (b) and light casting (c) with different carbides size and morphology—LM Figure 3 Non-etched longitudinal metallographic section with different carbides size and
S l é vá re ns t v í . L X I V . li s to p a d – p ro s in e c 2016 . 11–12
417
O D B O R N É R ECEN ZOVA N É ČL Á N K Y
Rp0,2 [MPa]
Dv –střední velikost γ’ [µm]
y = 0,031x - 26,38 R² = 0,9997 y = 0,0457x - 39,325 R² = 0,9799
8