7 minute read
Switches
Standard extra equipment and optional accessories are also shown and described.
35 36 37 38 39 40
41 42 43 44 45 46 47 48 49
PosDescription Page Remarks
35Working lights (backwards) 54 36Working lights and reversing lights 54 Optional 37Working lights (forward) 54 Optional 38Instrument light switch 54 Optional 39Extra high beam 54 Optional 40Main light switch 54 41Hazard light switch 55 42Rotating beacon switch 55 Optional 43Spare space 55 44Test switch for brake warning light 55 45Tipping system switch 55 46Automatic central lubrication indicator light 56 Optional 47Mirror heating switch 57 Optional 48Electrical heated driver's seat switch 57 Optional 49Cab and engine compartment light 57
35 36 37
35.Working lights (backwards) 91*
Push the switch to activate the working lights. Built-in light.
36.Working lights and reversing lights 20*
Push switch to activated the lights. Built-in light. The switch has three positions: 1.The working lights will light. 2.Neutral, the lights are switched off. 3.The reversing light will light when reverse gear is engaged.
37.Working lights (forward) 19*
Push the switch to activate the working lights. Built-in light.
38
38.Instrument light switch 4*
Push the switch to light all instruments. Built-in light. The instrument light will be turned off when this switch is off.
39 40
39.Extra high beam 21*
Push the switch to activate the extra high beam. Will only be activated if the high beam on column switch (56) is switched on. Built-in light.
40.Main light switch 90*
1st position, Side lights. When the switch is set to 1st position, the side/marking/licence plate lights illuminates. 2nd position, Headlights. When the switch is set to 2nd position the headlights (high or low beam according to position of column switch 56) will also illuminate. Built-in light.
41 42 43
44 45
Or
46
41.Hazard light switch 89*
Push switch to activate the hazard light, all direction indicators will flash at the same time. An indicator light (32) on the instrument panel will flash concurrently. Built-in light.
42.Rotating beacon switch 92*
Push switch to activate the rotating beacon on top of the cab roof. Built-in light.
43.Spare space
44.Test switch for brake warning light 5*
Push the switch and check that the warning light for brake fluid circuit failure (14) lights up.
45.Tipping system switch 716*
Push the switch to override the tipping system. For safety reasons, the tipping system is made in such way that it is not possible to tilt the body centre of gravity over the tipping hinges. •If an empty body shall be raised, it may be necessary to push the switch and keep it depressed while the body is lifted with the tip control lever. Release the switch when the body is raised. •If the body is resting on the body support, it is necessary to push the switch and keep it depressed while the body is lifted slightly. Release the switch when the body is off the body support and lower the body.
WARNING
Do not use this switch when tipping with load!
44 45
Or
46
Test button
Switches 46.Automatic central lubrication indicator light, green or yellow 22*
Lights when the automatic central lubrication is activated. The system performs all operation automatically. After the starter switch is turned on or is in operation the pump will at 30 minutes interval supply measured quantities of grease to all the lubrication points. The indicator light will then light up once. This pattern will be repeated 4 times.
Blink codes for the indicator light: (the buzzer will sound when the indicator light is flashing) •The light flashes 4 times once (0.5s on/0.5s off) as soon as the starter switch has been turned on:
Cause:The automatic central lubrication is activated.
•The light does not flash when the starter switch is turned on:
Cause: 1.The system is not powered. Check fuses and connection to earth and replace if necessary. 2. Lamp or wiring to lamp could be defective. Check lamp and wiring and replace if necessary.
•The light flashing for 2 minutes (0.5s on/0.5s off) at the beginning of each cycle:
Cause:Minimum grease level in the reservoir has been reached. Refill the reservoir as soon as possible, see 500 hours service for procedure.
•The light continuously light for 2 minutes at the end of the pumping phase:
Cause:Insufficient grease pressure. Contact you Moxy Dealer.
•The light continuously light after starter switch has been turned on:
Cause:System out of order! Immediate action is required. Possible causes: 1.Insufficient grease pressure during 10 consecutive cycles (or 10 consecutive times in the same main pipe channel). Check cause and reset by depressing the test button (on the reservoir) for at least one second while the starter switch is turned on. 2.Reservoir empty; refill the reservoir and after that depress the test button (on the reservoir) for at least one second while the starter switch is turned on.
•The light flashing during one complete cycle (2.0s on/2.0s off):
Cause:Single test run being executed (see "test") •The light flashing continuously (0.2s on/0.2s off):
Cause:Continuous cycle test run being executed (see "test")
Test button
Test
•In order to check the system a single lubrication cycle can be performed. 1.Starter switch turned on. 2.Depress the test button (on the reservoir) for 3 to 5 seconds. The system will run a single cycle test. During this test the light will flash (2.0s on/2.0s off). •In order to provide additional grease to all lubrication points (i.e after cleaning the dump truck) or to vent the system, a continuous lubrication cycle run can be performed. 1.Starter switch turned on. 2.Depress the test button (on the reservoir) for more than 6 seconds. The system will perform a continuous lubrication cycle run. During this run the light will flash (0.2s on/0.2s off). The continuous test cycle ends after the starter switch has been turned off.
47 48 49
47.Mirror heating switch 94*
Push the switch to heat the external mirrors for ice and condensation removal. Built-in light. Engage only when necessary!
48.Electrically heated driver's seat switch 205*
Push the switch to activate the heating of driver's seat. Built-in light.
49.Cab and engine compartment light 93*
Push the switch to light the cab and the engine compartment lights. Turn off during operation. Built-in light.
Standard extra equipment and optional accessories are also shown and described.
50 51 52 53 54 55
PosDescription Page Remarks
50Flamestart system indicator 59 Optional 51Flamestart system preheating switch 59 Optional 52Flamestart system cancellation switch 59 Optional 53Retarder brake main switch 60 Optional 54Engine brake switch 60 Optional 55Inter axle differential lock 60
50
51
52
50.Flamestart system indicator light, green 407*
Lights when glow plugs for the flamestart system are activated.
51.Flamestart system preheating switch 410*
Push the switch and keep it depressed to activate the flamestart system. 1.With the starter switch (65) in position I and the gear selector in neutral position, keep the switch depressed for approx. 15 sec. (max. 20 sec) before starting the engine (pre-heating). 2.Continue to keep the switch depressed while the starter switch (65) is turned to position II and the engine starts. 3.When the engine starter is engaged, the switch can be released and the time relay will automatically keep the system going for 5 minutes, as long as no interruption is made (see item 52).
An indicator light (50) will light as long as the glow plugs are activated.
NOTE
To activate the flamestart system the gear selector must be in neutral position and the preheating switch must be kept depressed until the engine starter is engaged.
52.Flamestart system cancellation switch 412*
To interrupt the connection to the glow plugs, the cancellation switch must be pushed to break the circuit to the time relay. Interruption of the connection to the glow plugs will also take place if the gear selector (61) is moved out of neutral position or the starter switch (65) is turned off.
53
54
55
53.Retarder brake main switch 81*
Push the switch to engage the retarder brake. The retarder brake will only engage when a gear is selected, lockup connected and the throttle pedal released. Built-in light. If the switch is not installed, the retarder brake will engage automatically when a gear is selected, lock-up connected and the throttle pedal released. An indicator light (33) will light when engaged. The retarder brake effect must be controlled by the retarder brake lever (62). If this lever is in off position, the retarder brake will not function even if the main switch is on.
54.Engine brake switch 80*
Push to engage the engine brake. The engine brake will only engage when a gear is selected, lockup connected and the throttle pedal released. Built-in light. If the switch is not installed, the engine brake will engage automatically when a gear is selected, lock-up connected and the throttle pedal released. An indicator light (30) will light when engaged.
55.Inter-axle differential lock 77*
Push the switch to engage the inter-axle differential lock. Engine power and wheel speed determine when the lock engages. An indicator light (31) will light when the lock is engaged. Built in light.
