4 minute read
Specifications
SPECIFICATIONS
All specifications are subject to change without notice. Always consult BUCYRUS to obtain current information before applying critical loads.
Capacities
Bucket Payload 8000 kg RAS forks maximum payload 10000 kg RAS fixed jib maximum payload 7000 kg RAS slewing jib maximum payload 7000 kg RAS belt reeler 7000 kg Maximum unbraked trailer mass 10000 kg Maximum braked trailer mass Consult Bucyrus
Standard Ejector Bucket
Heaped capacity (SAE) 4.5 m³ Struck capacity 3.5 m³ Steer/brake system Pressure10 micron replaceable with bypass
Bucket Pump
Type Gear open centre Standard pump output @ 2100 RPM 228 lpm
Steer and Brake Pump
Type Pressure compensated piston closed centre Standard pump output @ 2100 RPM 106 lpm
Cooling Fan Pump
Type Gear open centre
Alternator Drive Pump
Type Gear open centre
Weight
With bucket only 29000 kg Without bucket 26500 kg
Engine
Type Diesel, turbocharged, 4 cycle Cooling system Water based radiator Cooling fan Hydraulic driven fan Engine make/model Caterpillar 3126 Displacement 7.2 litre Maximum power 153 kW @ 2300 RPM
Engine Speeds
Low idle 800 RPM High idle 2600 RPM
Fuel Consumption
At full power 45 litre/hr Average mine duty 12-40 litre/hr
Cylinders
Type Double acting Rods Hard chromed Counterbalance valves Lift and tilt Cushion stops Steering and tilt
Steering System
Control valve Closed centre Actuation Orbital
Bucket System
Control valve Actuation Open centre Remote hydraulic pilot
Service/Brake Hydraulic System
Type Reverse modulating Control valve Closed centre Actuation Foot pedal Operating pressure 0 to 17.10 MPa
Start System
Starter motor type Air turbine type
Intake Air Cleaner
Type Dry dual element Intake flame trap Bucyrus spiral wound type
Exhaust Conditioner
Type Flameproof wet type Make Bucyrus Exhaust Filter Replaceable element Exhaust flame trap Wet After treatment Catalytic exhaust purifier
Transmission
Type Power shift with forward/reverse modulation Speeds, forward and reverse 4
Axles
Type Outboard planetary Differential type Bevel gear and pinion Differential lock type - front Posi-Torque Differential lock type - rear Posi-Torque
Wheels
Make/model 5 piece (heavy duty)
Tyres - Standard
Size 20.5 x 25 Ply rating Radial Inflation media Air Inflation pressure 110 psi front, 110 psi rear
Accumulator - Brakes
Type Piston Quantity x capacity 1 x 2 litre
Service Brake
Type Totally enclosed, liquid cooled Posi-Stop Application Spring applied hydraulic release Location Each wheel end built into axle
Park Brake
Type Totally enclosed, liquid cooled Posi-Stop Application Spring applied hydraulic release Location Each wheel end built into axle
Hydraulic Filtration
Bucket system Return 10 micron replaceable with bypass
Steering
Type Centre articulated, hydraulic
Articulation
Bearing type and size Pin and spherical bearing (top), bush (bottom) fully sealed
Bush material Hardened steel
Pin material Degrees of turn either side Hardened steel 45 degree
Oscillation
Type Bush material
Rear axle mounted trunnion Hardened steel Pin material Hardened steel Degrees up and down from horizon 7.5 degree
Seating (Operator)
Type Cross-seated Make Bucyrus Suspension Adjustable spring/shock absorption
Canopy
Type Protective device MDG1
Electrical system
Type Approved flameproof Voltage 12 V Polarity Negative ground
Electronic Shutdown System
System type Electronic Intrinsically safe approved
Lights
Number/location STD 2 front, 2 rear
Alternator
Drive Hydraulic Type Bucyrus approved flameproof
Pneumatic System
Compressor type Piston engine gear driven Air flow 0.340 m³/min @ 1500 RPM Governed pressure 800 kPa Relief pressure 830 kPa Air receiver volume 80 litre
Vehicle Speeds
1st gear 3.6 kph 2nd gear 8.6 kph 3rd gear 15 kph 4th gear 27 kph
Grade Ability
Front to rear 1:4 Side to side (empty) 1:4 Side to side 1:8 (Laden bucket load fully raised)
Service Capacities
Hydraulic tank 300 litre Fuel tank 300 litre Main air receiver 80 litre Transmission/converter oil 45 litre Engine crankcase oil (with filter) 22 litre Engine cooling system water 72 litre Axle oil (each) 60 litre Wheel ends (each) 5.5 litre Wet scrubber system (total) 780litre
All specifications are subject to change without notice.
Options (Others available on request):
Filled tyres – insert or foam Load indication gauge system Fire suppression system Tow chains Auto lubrication system Alternative approved electrical components (lights, alternators, hour meters etc.)
The FBL-10 comes standard with the Rapid Attachment System (RAS) for rapid pick up and release of attachments.
Optional attachments available:
15000 kg Forks with side shift 10000 kg Belt/cable reeler 8000 kg Slewing jib crane 4.5 m3 Bucket Elevating work platform Fuel and lubrication pod Trailer towing adapter (CHT-50) Concrete hopper attachment
Contact your local BUCYRUS representative for further information on any of the above listed attachments. If you have a specific job task requirement or an attachment that is not listed let BUCYRUS assist by developing a solution for and with you.
