1 10] Parking brake parking lock ...................................................... 33.1

Fuel tanks must kept full possible limit the amount air and water vapors in them. may necessary drain the fuel filter water trap more frequently .

Potential oxidation and stability could a problem with the fuel stored in the machine. NOTICE: Machines must not stored for more than 3 months with Biodiesel fuel blends in the fuel system.

longer storage periods are necessary , the engine must run pure diesel fuel for a minimum h flush the Biodiesel fuel out the fuel system prior storage. NOTICE: Biodiesel Fuel must not stored in - site + tanks for more than three months.

Any spillage Biodiesel fuel must cleaned immediately before it can cause damage the environment and the paint finish the machine.

Before using Biodiesel fuel blends you should consult with your dealer receive full information about the approved blend for your machine and any detailed conditions its usage. NOTICE: Be aware that not fulfilling the requirements and conditions Biodiesel fuel usage will void your machine’ s CASE warranty coverage.

Coolant

W ARNING

Chemical hazard! Follow the instructions the container when handling anti freeze. Failure comply could result death serious injury .

109A

Use antifreeze in all seasons protect the cooling system from corrosion and all risk freezing.

For areas where ambient temperature is over °C (32.8 °F ), use a blend % ethylene - gylcol based antifreeze.

For areas where the temperature is below °C (32.8 °F ), it is advisable use a blend % water and %

antifreeze. NOTICE: not use coolant with antifreeze concentration greater than % (point congelation is °C (°F ),

boiling point is 1 °C ( 230 °F )) unless absolutely required.

Never use antifreeze concentration over %! We not recommend the blending antifreeze agents. Blending various types coolant may cause loss anticorrosion properties.

Always check the antifreeze concentration the coolant with a refractometer before the winter season starts.

Hydraulic oil

Only hydraulic oil CASE AKCELA - TRAN® TRA™ HYDRAULIC TRANSMISSION OIL may used for the machine’ s hydraulic system. Fill the machine with hydraulic oil cinematic viscosity 2 / s °C ( 104 °F ) , i.e. ISO VG 68. This oil is most appropriate for use within the widest range ambient temperatures.

Synthetic hydraulic oil

is possible fill the hydraulic system with synthetic oil for which any leakage will completely biodegraded via microorganisms found in water and soil. NOTICE: Always consult with the oil manufacturer dealer before switching from mineral oil synthetic oil mixing oils various brands!

T ransmission fluid

Use CASE AKCELA GEAR 135 H EP 80W - for outdoor temperature 10.0

30.0

°C ( 14.0

86.0

°F ).

Use CASE AKCELA TRANSAXLE FLUID 80W - 140 for outdoor temperature 20.0

45.0

°C ( 68.0

- 1 13.0

°F ).

NOTICE: The operating temperature the fluid must not exceed °C ( 185.0

194.0

°F ).

Lube grease

Use plastic lubricant with lithium content lubricate the machine: Case Akcela Extreme pressure grease moly

W asher fluid

Use water (up 0 °C ( °F ) and motor vehicle glass washer fluid when filling the washer fluid reservoir . NOTICE: Fill with a winter - rated motor vehicle glass washer fluid when temperatures are below 0 °C ( °F ).

Use plastic lubricant with lithium content lubricate the machine: Case Akcela Extreme pressure grease moly

V ibrator cooling mixture (only for SV212 and SV216)

Mixture SV212 • 22.0 l ( 5.8 gal ) water • 50.0 (1 10.2 ) % calcium chloride - CaCI2 Mixture SV216 • 30.0 l ( 7.9 gal ) water • 66.6 ( 146.8 ) % calcium chloride - CaCI2

Part T ype Quantity SV 208 Quantity SV 210 Quantity SV 212 Quantity SV 216 Icon

Engine Engine oil 7 l ( 1.85 gal ) 11 l ( 2.9 gal )

Fuel tank Diesel 275 l ( 72.6 gal ) 410 l ( 108.3 gal )

Hydrostatic system Hydraulic oil l ( 19.3 gal ) l ( 23.8 gal )

Hinge bearings - steering joint and steering cylinders Plastic grease As required As required