User Guide 1.888.353.0677 | support@Go4-D.com
Part 1 | Getting Started
2
3D Scanner Contents F
G
H
I
J
K
L
M
D
E
The 3D Scanner package includes:
C
C. 3D Foot Scanner D. Handle bars and two extension rods E. Two Support Steps F. AC adapter G. Power cord with C13 plug H. Lifting straps I. USB cable
J. 4 screws to mount the handle bar to the 3D Scanner K. 4 knob screws to mount the Support Steps L. Allen key (attached to lifting strap) M. USB Hub
Pressure Plate Contents
N
O
P
The Pressure Plate package includes: N. Pressure Plate O. USB cord P.Port Protector
3
Part 2 | Installation
4
3D Scanner Unpacking and Installation Note: Please keep the original Scanner packaging Cut the straps to release the accessories box from the 3DScanner box. Remove the accessories box and set aside.
The 3D Scanner box consists of an upper and bottom half. Remove the plastic handles on front and rear side. This will remove the lock between the upper and bottom parts. Lift the upper cardboard off the box.
In the main box, you will find an additional box with the USB Hub (M). Set aside next to the Sprout for later use. Please make note of the two long narrow boxes on top of the scanner. These boxes are not just packaging -- they include the power cord (G), USB cord (I) and AC adapter (F).
The four sides of the bottom cardboard will fold down allow full access to the 3D Scanner. Remove the protective foam from around the 3D Scanner
Lift the 3D Scanner with two people using the attached straps. Place the 3D Scanner at the point of use on a flat surface. Pleasedo not place under direct lighting or sunlight for best scanning results.
5
Remove the allen key (L) from the lifting strap. Use the allen key to remove the four hex screws and washers that hold the lifting straps in place. Store the straps and screws for future use. Remove the protective parts inside the scanner.
The connections and power switch are on the rear of the scanner. Orient the front of the scanner to face where the customer will be standing.
Make sure the scanner is level on a solid floor. Adjust the four feet to level the 3D Scanner by turningthem clockwise or counter clockwise.
Open the accessories box and remove the parts. This box includes the handle bars with two extension rods (D), two support steps (E) and 4 screws (J).
6
Secure the two extension rods for the handle bar and to the back of the scanner using the four screws and allen key supplied. The four protection pads on the rods will be positioned towards the scanner.
Slide the handle bar over the extension rods until the hex screws are visible through the holes in the handle bar. Turn the hex screws slightly clockwise or counter clockwise when the rods cannot be fully inserted in the handlebar. Turn the hex screws clock wise to secure the extension rods.
Place the steps next to the scanner, align the mounting holes with the holes at the sides of the scanner and secure them using the four knobs. Adjust the steps until they are supported by the floorand fasten the knobs.
Ports 1.Power switch: to switch the 3D Foot Scanner on or off 2.Power LED: to indicate that the 3D Foot Scanner is powered on 3.Power: connect the supplied AC adapter. DO NOT use any other AC adapter 4.USB: connect to the USB hub connected to the Desktop Screen
7
Connecting the 3D Scanner Inside of the 3D Scanner box you found a box with the USB Hub (M). Connect the USB Hub to one of the USB ports on the backside of the Desktop Screen (A) and feed the power cord through the pedestal pole (S) and base (R) to connect to the power strip. As you continue with installation, rather than connecting the scanners directly into the Desktop Screen they will always connect via the USB Hub. The USB Hub will serve as a port between the Desktop Screen and both the 3D Scanner and Pressure Plate to allow for a sufficient power supply.
Verify that the power switch on the 3D Scanner is in the OFF position (marked as O).
Connect the AC adapter (F) to the 3D Foot Scanner (C).
Connect the power cord (G) to the AC adapter (F) and then plug it into the AC outlet.
Connect the 3D Foot Scanner to the Desktop Screen using the supplied USB cable (I). Connect the USB-A plug side of the cable (flat, rectangular plug) to the USB Hub (M) and run the cable from the USB Hub through the pedestal pole and base.
The USB-B plug side of the cable (square plug) will connect to the USB connection on the 3D Scanner.
When the hardware setup is completed, switch on the 3D Scanner by switching the power switch to the ON position (marked I). The green power LED inside the switch will light up.
8
Pressure Plate Installation Note: Please keep the original Scanner packaging With the box oriented upwards, open the Pressure Plate box and remove the Pressure Plate (N).
Remove the protective foam around the Pressure Plate and set aside the accessory bag containing the USB Cable (O) and Port Protector (P)
Set Pressure Plate on a flat surfaces with sufficient room for customers to walk across with a naturalstride.
N
M Connect the USB cord (O) to the USB Hub (M) and run the cord through the pedestal pole and base to the Pressure Plate. NOTE: 0.5 m pressure plates do not require a USB hub. The USB hub is only shipped with 1.0, 1.5 or 2.0 m plates.
O
P
On the backside of the Pressure Plate there is a Velcro panel that opens to expose the USB port. Connect the USB cable and run the cord through the channel on the side ofthe Pressure Plate.
The Port Protector (P) is located within the accessories bag as well. One edge of the Port Protector has a raised edge. This edge will face outwards. Snap the Port Protector to the USB cable and slide into position at the opening of the PressurePlate.
9
Important Notice You are required to store the boxes in which the scanners were shipped. The reason for this is to return the scanners for maintenance or in the unlikely event of repair. If the boxes are not retained, and a scanner requires maintenance or repair, a fee will be charged to the clinic to ship empty scanner boxes. Shipping scanners in any box or container other than those designed for that purpose may result in damage. Any damage to a scanner shipped improperly will be the responsibility of the clinic. Thank you for your cooperation.
Re-boxing the 3D Scanner Start by disconnecting the 3D Scanner power cord from the back of the 3D Scanner and the power strip. Disconnect the USB cord from the USB Hub.
Unscrew the four knob screws on the side of the 3D Scanner that attach the side steps and remove from the 3D Scanner.
Remove the handles from 3D Scanner by unscrewing and lifting off the stop section of the handle bar.
Remove the lower section of the extension rods by unscrewing from the 3D Scanner.
Locate the orange straps that were removed from the 3D Scanner at installation.
11
Use the provided allen key to reattach the orange straps to the sides of the 3D Scanner. They will function as handles to lift and lower the 3D Scanner back into the original box.
Replace the protective foam pieces and the foam corners around the 3D Scanner inside the box.
Pack the power cord and USB cable into one of the two small rectangular boxes and the other side of the power cord into the other small box. Replace these two boxes on top of the spacer foam on top of the 3D Scanner in the box.
Pack the Handle Bar, Extension Rods and Side Steps into the additional box that came with the 3D Scanner.
12
Re-boxing the Pressure Plate Start by opening the velcro panel on the back of the Pressure Plate and remove the Port Protector to allow for easier removal of the USB cable from the Pressure Plate.
Disconnect the USB cable from the port then disconnect the other end of the cable from the USB Hub.
Slide the Pressure Plate back into the plastic sleeve and replace the protective cardboard caps on the ends of the PressurePlate. Insert the foam spacers on both ends and middle of the Pressure Plate. Place the USB Cord and Port Protector back in the accessories bag and placein the box on top of the PressurePlate.
13