Con-Tech Replacement Parts Catalog 2023

DODGE

Minnesota (Midwest) 65740 State Hwy. 56 Dodge Center, MN 55927

dcsales@ctmmixers.com

507-374-2239 ATLANTA

Georgia (Southeast) 108 Hudson Industrial Dr. Griffin, GA 30224

southeast@ctmmixers.com

770-229-1773

CLEVELAND Ohio (Northeast) 38134 Western Pkwy., Unit 2 Willoughby, OH 44094 northeast@ctmmixers.com 440-946-3322

DALLAS

Texas (South Central) 205 Wilcox St., Ste. 100 McKinney, TX 75069 dallas@ctmmixers.com

972-941-8592

HOUSTON

Texas (South Central) 11175 Windfern Rd. Houston, TX 77064 houston@ctmmixers.com 832-688-8449 SAN

OEM PARTS FOR CTM & REPLACEMENT PARTS FOR mtm MIXERS

RETURN POLICY

You must contact your sales representative prior to obtaining a Return Authorization.

The Return Authorization (RA) will be valid for 45 days from the issue date. After 45 days Con-Tech Manufacturing, Inc. will close the RA and it will no longer be valid. Please mark the RA number clearly on all shipping cartons and paperwork. When requesting an RA number/form, please be prepared to provide the following information:

• Customer name

• Customer shipping address

• Customer billing address

• Customer phone number

• Customer contact

• Customer contact e-mail

• Equipment type and/ or serial number

• Original sales order or purchase order number

• Reason for return

Having this return policy in effect will ensure that all of our customers receive their parts credit(s) in an efficient and timely manner. Returns are subject to a 15% restocking fee.

REPLACEMENT PARTS WARRANTY

Con-Tech Manufacturing, Inc., a Minnesota corporation, hereinafter referred to as Con-Tech, warrants replacement parts sold by Con-Tech to be free from defects in material and workmanship under normal use and service for a period up to one year. Con-Tech’s obligation under this warranty is limited to repairing and replacing, at ConTech’s opinion, any parts which are returned to Con-Tech’s factory at Dodge Center, MN 55927. Transportation charges must be prepaid by the customer. Parts must be returned within 30 days after date of delivery to customer. This warranty covers only parts which, upon examination by Con-Tech, are found to be defective in material or workmanship. Such repair or replacement of parts under this warranty will be made by Con-Tech without charge for such parts. Under no circumstance will Con-Tech be under any further liability with respect to such warranty. Replacement parts purchased by Con-Tech from other manufacturers shall be covered by that manufacturer’s warranty.

Con-Tech warranty shall not apply to parts that have been subject to misuse, negligence, accident, or which has been repaired or altered without Con-Tech’s prior knowledge and consent.

IN NO CASE SHALL CON-TECH BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL, OR INDIRECT DAMAGES OF ANY KIND.

Con-Tech makes no other expressed or implied warranties of fitness or merchantability or any other warranties, either expressed or implied. Any implied warranty of merchantability or fitness for a particular purpose which exceeds the forgoing warranty is hereby disclaimed by Con-Tech. There are no warranties which extend beyond the description on the face hereof.

BridgeKing®, Ecofin™, Armor-Tech™, Extreme Duty™, and Con-Tech Manufacturing, Inc.® are trademarks that are property of Con-Tech Manufacturing, Inc., Dodge Center, Minnesota. This publication is copyrighted by Con-Tech Manufacturing, Inc. and should not be duplicated or used in any form electronically or otherwise .

COMPATIBILITY OF PARTS & USAGE

All items in this book are marked with CTM (Con-Tech Manufacturing, Inc.), mtm (McNeilus Truck and Manufacturing, Inc.), or CTM/mtm, which indicates the compatibility and usage of the individual parts.

Con-Tech manufactures OEM (Original Equipment Manufacturer) fabricated metal replacement parts only for CTM mixers. The fabricated metal replacement parts referred to with respect to mtm mixers in this book are “Will Fit” parts for mtm mixers manufactured by Con-Tech. They are not OEM parts (i.e., parts manufactured and/or supplied by McNeilus Truck and Manfacturing, Inc.) for mtm mixers. Con-tech makes no representation that any replacement parts referred to in this book are manufactured by McNeilus Truck and Manufacturing, Inc.

AFTERMARKET PARTS TERMS AND CONDITIONS

Please review Con-Tech Manufacturing, Inc.’s Aftermarket Parts Terms of Sale. Please contact Con-Tech Manufacturing, Inc., hereinafter referred to as Con-Tech, with questions or for further information.

1.1 PRICES

Every term and provision of prior parts quotations and of the pricing and delivery time above is subject to, and customer agrees to be bound by, changing conditions resulting from: prior sales, fluctuations in currency exchange rates, material surcharge assessments, fuel surcharge assessments, component pricing escalations, material pricing escalations, labor cost escalations, lack of timely component availability, shipper limitations, vendor limitations, ConTech factory capacity, and force majeure events.

• Prices do not include state sales tax, excise tax or any other government charge upon production, sale, or shipment of goods, now imposed or hereafter becoming effective, which shall be added when, as, and if applicable.

1.2 TERMS OF PAYMENT

Con-Tech’s requested methods of payment are check and ACH. Credit cards are accepted as an alternative payment method but will be subject to a 3.3% convenience fee. Accepted credit cards are Visa, MasterCard, American Express, and Discover.

• Customer accounts are initially set up with PIA (Payment in Advance) terms. Con-Tech’s PIA terms state the invoice will need to be paid before the order is shipped.

• Upon approval of credit application, customers’ accounts will have Net 30 terms. Please request a credit application from your sales representative or Con-Tech’s main office.

• A 12% annual (1.0% per month) finance charge applies to all invoices past their due date. Customer accounts may be placed on purchasing hold if they have an overdue invoice.

• Overpaid invoices will be turned into credit memos and sent to the customer. Credit memos may be used in your future payments or paid back upon request. All credit memos over 90 days will be issued back to the customer.

• The customer authorizes Con-Tech to exercise peaceful possession over such items that have not been paid for in full at Con-Tech’s discretion.

1.3 TAX AND EXEMPTION CERTIFICATES

It is the customer’s responsibility to know if they are tax exempt based on their ship-to state’s laws.

• I t is the customer’s responsibility to send Con-Tech a complete, current, and correct copy of their tax exemption certificate or reseller’s permit (dependent on your state’s laws).

• If Con-Tech does not receive a copy of the customer’s completed exemption by the first of the month following the date of the invoice, Con-Tech will expect the tax to be paid by the customer.

1.4 LIMITED WARRANTY ON AFTERMARKET PART SALES

Equipment or accessories purchased by Con-Tech from other manufacturers shall be covered by that manufacturer’s warranty.

Con-Tech’s obligation under warranty is limited to repairing or replacing, at Con-Tech’s discretion, any parts which are returned to Con-Tech’s factory at Dodge Center, Minnesota 55927. Transportation charges must be prepaid by the customer. This warranty covers only parts which, upon examination by Con-Tech, are found to be defective in material or workmanship. Such repair or replacement of parts under his warranty will be made by Con-Tech without charge for such parts. Under no circumstances will Con-Tech be under any further liability with respect to such warranty.

• In no case shall Con-Tech be liable for consequential, incidental, special, or indirect damages of any kind.

• Con-Tech warranty shall not apply to components that have been subject to misuse, negligence, accident, acid use, liquid nitrogen exposure, contamination or which has been repaired or altered without Con-Tech’s prior knowledge and consent. (Continued on the next page)

• Con-Tech makes no other expressed or implied warranties of fitness or merchantability or any other warranties, either expressed or implied. Any implied warranty of merchantability or fitness for a particular purpose which exceeds the forgoing warranty is hereby disclaimed by Con-Tech. There are no warranties which extend beyond the description on the face hereof.

• The customer’s exclusive remedy for breach of warranty as a result of defects in material and workmanship shall be as set forth herein. Any action for breach of warranty must be commenced within 30 days after the cause of action shall accrue, and no such action may be maintained which is not commenced within such period. Con-Tech neither assumes nor authorizes any other persons to assume for it any liability in connection with its equipment.

• Used parts are not covered by any warranty terms continued herein.

TERMS FOR PARTS COVERED UNDER LIMITED WARRANTY

• Elec trical components, including but not limited to, electrical controllers, cables, switches, solenoid valves, and lights are warranted 90 days against defects in materials and workmanship.

• O ther aftermarket parts, excluding electrical components, including but not limited to, gauges, harnesses, hydraulic cylinders, air cylinders, hydraulic pump/motors, gearboxes, and hoses are warranted for one year against defects in materials and workmanship.

1.5 CANCELLATIONS

In the event of order cancellation, labor and materials costs allocated towards the agreed upon order shall be the sole responsibility of the customer and charged as such. This includes (but not limited to) raw materials, shop supplies, goods in the process of manufacture, any labor involved in the assembly of the order.

• Con-Tech reserves the right to cancel the entirety of an order in the event of a partial cancellation by the customer.

1.6 RETURNS OF ORDER

You must contact your sales representative to obtain a Return Authorization. Parts must be returned within 30 days after date of delivery to customer. The Return Authorization (RA) will be valid for 45 days from the issue date of the invoice. After 45 days, Con-Tech will close out the RA and it will no longer be valid. Please mark the RA number clearly on all shipping cartons and paperwork.

• Returns are subject to a 15% restocking fee.

1.7 FREIGHT CLAIMS/CHARGES & ASSESSMENTS

Con-Tech is not responsible for freight rates charged by carriers. All parts sold by Con-Tech are F.O.B. Origin and ships standard ground service unless otherwise specified by the customer.

• If a shipment arrives damaged in transit, the customer must note the damage on the Bill of Lading and contact Con-Tech immediately.

• Con-Tech is not responsible for delays resulting from strikes, accidents, negligence of carriers or other causes beyond our control.

• If Con-Tech receives any additional fees or assessments for shipping, including but not limited to, expedited freight, guaranteed delivery, and liftgate usage, the customer will be responsible for those fees incurred. ConTech will send out a freight-only invoice for the assessed charges.

1.8 PRODUCT CHANGES

Con-Tech reserves the right to make changes to patterns, design, or materials at any time without prior notification or obligation to make corresponding changes in previous models.

UPDATED AS OF 01/20/2023

POLICIES & SCHEDULES

Return Policy

Replacement Parts Warranty

Compatibility of Parts & Usage

Terms & Conditions of Sale

Parts Covered Under Limited Warranty

Service & Maintenance Schedule

CHUTES

Main & Foldover

Foldover, Transition, & Extension

Chute Racks & Mounts

Chute Accessories

HOPPERS & COLLECTORS

Hoppers & Accessories

Collectors & Accessories

PEDESTALS

Rear Pedestals & Components

Ladders & Platforms

Rear Pivot

Chute Locks & Accessories

Rollers, Guards, & Ped Hardware Front Pedestals Hose

WATER SYSTEM

Aluminum & Steel Water Tanks

Poly Water Tank System

Mounts, Straps, & Saddles

High Overhead Water Tank Configurations

Sight Gauge Mount Parts

Sight Glass & Strips

Floppers & Gaskets

Valves & Shut-Offs

Hoses & Nozzles

FENDERS & BUMPERS

Poly-Tuff® Fenders, Supports, & Accessories

Steel & Aluminum Fenders & Supports

Mudflaps & Accessories

BridgeKing® Fenders

Aftermarket Front Bumpers

Rear Bumpers

DRUM PARTS

Con-Tech’s High Performance™ Drum

Fins & Fin Kits

Ball Busters & Hatch Accessories

ELECTRICAL

Lights & Accessories

Alarms, Cameras, & Displays

CTM Wiring Harness Layout & Harnesses

Armor-Tech™ Wiring System

ACCESSORIES & TOOLS

Connection Tools, Wheel Chocks, & DOT Accessories

Tool Boxes, Bucket Racks, & Cone Holders

Testers, Adjustment Tools, & Accessories

WASHOUT SYSTEM

EcoWash™ Automatic Wash System

Chute Wash Recovery

Watch Dog Washout System

Enviroguard®

Drum Sprayer System

DEC ALS & PLACARDS

Safety Decal Placement

Sight Strips & Mixer Data Cards

Placards

RESOURCES

Plant Parts

Non-CTM/mtm Parts

High Performance™ Drum Order Form

Pre-HP™ & mtm Drum Order Form

Front Pedestal Order Spec Sheet

Rear Pedestal Order Spec Sheet

High Performance™ Hopper Order Form

‘Gun Rack’ Tab Order Form

Business Credit Application

change after every 1,000 hours. (All)

CON-TECH

ARE CAPPED AND FULLY WELDED!

CON-TECH CHUTES ARE CAPPED AND FULLY WELDED!

STANDARD ALUMINUM EXTENSION CHUTES ( BY MEASUREMENT )

OUR NEW PAINT PRIMER

Imron® High Performance Urethane DTM Primer

A two-component, low VOC, direct to metal, urethane primer. It delivers high quality topcoat holdout, minimum over-spray, excellent over spray melt in and high build over properly treated metal substrates.

ENVIRONMENTALLY FRIENDLY CORROSION PERFORMANCE

HYPER CURE™ TECHNOLOGY

OTHER MAKES AVAILABLE THROUGH CON-TECH PARTS:

215478

215476

215470

Front Chute Rack Mount (RH) CTM / mtm

215958

Chute Rack - Pedestal Mount, Antler Rack CTM / mtm (Production Up to 03/21)

215551

HP Chute Rack - Pedestal Mount, Rear 14” Depth, BK CTM / mtm (Production Up to 03/21)

215092

Chute Rack - Pedestal Mount StopPre-HP CTM Rear, Current Front, 9” Depth CTM / mtm

216269

Chute Rack - Pedestal Mount, WLDT, Antler Rack (For Use with 216266) CTM / mtm (Post 03/21)

216266

Chute Rack - Pedestal Mount Stop11.5” Depth (For Use with 216269) CTM / mtm (Post 03/21)

216206

Chute RackRail Mount CTM / mtm

Front Rack Mount Offset (LH) CTM / mtm

215500 Front Rack Mount Offset (RH) CTM / mtm

Front Chute Rack Mount (LH) CTM / mtm

215055

42” Collector - Standard mtm

215060

46” Collector - HP PVR CTM / mtm

705324

Hardware Kit - Collector Includes: (6) 705303 Bolts, (12) 705311 Washers, (6) 705314 Lock-Nuts CTM / mtm

215965

42” Collector - Wide Standard CTM / mtm

215571

Collector - Full Body HP Paver CTM / mtm

RETROFIT TO EXISTING EQUIPMENT

IN-STOCK BARE & FULLY-LOADED REAR PEDESTALS

OEM CON-TECH MFG, INC. & WILL-FIT mtm MIXERS

Con-Tech’s rear pedestal has taken mixer design and maintenance to a new level. Incorporating bolt-on uprights, hoop, and ladders make replacing commonly damaged components simple, quick, and easy.

PLEASE CALL FOR DETAILS ON ANY OF YOUR PEDESTAL NEEDS - 507-374-2239

High Performance Ladder Systems

LARGE GRAB HANDLES

Eliminates pinch points and promotes three points of contact.

10° CLIMB ANGLE & LEVEL RUNGS

Improves balance and ease of climb.

LARGE OPEN TREAD DESIGN

Improves traction and reduces material buildup.

2018 - CURRENT CTM

RETROFIT TO EXISTING EQUIPMENT

Please call with upper railing measurements to ensure proper railing fit and safety. Measuring is the best way to order.

RETROFIT TO EXISTING EQUIPMENT

DISCLAIMER: Please call with upper railing measurements to ensure proper railing fit and safety. Measuring is the best way to order.

PEDESTALS / REAR PIVOT

215128 Rear Pivot Housing (Type A)

215129 Rear Pivot Housing (Type B)

215781

A-Frame - Pivot Housing, HP, A Ped CTM

215633

Pre-HP Main Pivot Assembly, 11.5”

215664 HP Main Pivot Assembly, 11.0” (Short)

622500

215782 A-Frame - Pivot Housing, HP, B-Ped CTM

622501

HP Main Pivot w/ Bearing Kit, 11.0” (Short) CTM 725014

Pre-HP Main Pivot

215103

Disc Rear Brake Plate CTM /

216322

Mounting Bracket - Type A Air Chute Lock Can (Bolt-On) CTM / mtm

216375

Mounting Bracket - Type B Air Chute Lock Can (Bolt-On) CTM / mtm

600200 Brake Can - Assembly With Quick Dump and Tube CTM /

785001

785151

Chute Lock Air Chamber (Mounted vertically under frame) mtm

705036 Washer - Chute Lock CTM / mtm

705034 Spring - Chute Lock CTM / mtm

#16 Brake Can CTM / mtm

mtm

mtm

705035 Roll Pin - Chute Lock 5/32” x 1-1/2” CTM / mtm

750001

100123

216020

Roller Guard Quarter Front RH CTM / mtm

216019

Roller Guard Quarter Front LH CTM / mtm

216018

Roller Guard - Quarter Rear LH / RH CTM / mtm

Con-Tech Manufacturing, Inc. Roller Guards

CREATES A SAFE ZONE Buffer area is created around the rollers while they are turning.

WIDE SLOTS ACROSS GUARDS Makes for easy cleaning in and around the roller assemblies.

245196

Bracket - Hose Block Mounting CTM / mtm

720020

Hose Separator Block, 12-16 CTM / mtm

720024

Hose Separator Block, 12-8 CTM / mtm

720026

Hose Separator Block, 16-12-16-16-12 CTM / mtm

720027

Hose Separator Block, 12-6-6 CTM / mtm

720030

Hose Separator Block, 16-4-6-6-6-6-12 Top CTM / mtm

720028

Hose Separator Block, 16-4-6-6-6-6-12 Bottom CTM / mtm

720029

Hose Separator Block, 6-6-8 CTM / mtm

720033

Hose Separator Block, 12-16-16-12 CTM / mtm

760075

MAC Manifold - Chute Lock CTM / mtm

760085

MAC ManifoldChute Lock, Hopper CTM / mtm

760080

MAC Manifold - Chute Lock, Hopper, Pusher CTM / mtm

760088

MAC Manifold - Chute Lock, Hopper, Pusher, Tag Axle CTM / mtm

760052

Valve - Chute Lock, MAC “AAH” CTM / mtm

760053

Valve - Hopper, MAC “FAH” CTM / mtm

760054

Valve - Axle, MAC “DAH” CTM / mtm

735004

Filter - Coalescing , Camozzi, Assembly w/ DOT Fittings CTM

735008

BowlCamozzi Coalescing CTM

735006

ElementCamozzi Coalescing CTM

285258

SpacerCoalescing Filter CTM

735015

Filter - Parker, Coalescing, Aluminum Assembly mtm

735016

Bowl - Parker Coalescing, Aluminum mtm

735014

Bowl - Parker Coalescing, Clear Poly mtm

735017

ElementParker, Coalescing mtm

725048

O-RingParker Coalescing Bowl mtm

760145

ValveManual Hopper Air CTM / mtm

740008 Core - ASA Fan Cooler w/ Mounting Brackets

715154 Assembly - Fan Control Relay (Recommended with 740010)

740012

Switch - ASA Hydraulic Fan Temp O/S (1/2” BSSP - G12) (2007 to 9/30/2010 CTM)

740013

Switch - ASA Fan Temp. N/S (M14x1.5) (After 9/30/2010 CTM)

715065

740011

710047 Adapter - ASA Fan Assembly #12

760158 CTM

Valve - Parker Directional, BridgeKing® Includes

CONVERSION TO MTM REQUIRES 715052 & 715209

760158 mtm

Valve - Parker Directional, BMV Conversion (Conversion to mtm requires 760158, 715052, 715209) mtm

760015 mtm

Valve - Parker Directional, BMV (No longer available, Replace with 760158 BMV Parker Valve Conversion to the left) mtm

760014

Parker Valve Coil w/ Female Weather Pack

760062 Parker Valve Coil w/ Male Weather Pack

COIL REPLACEMENT REQUIRES 715052 & 715209

715052

715209

760199 Parker Valve Coil

705066

Chute Up / Down Coil

760156

Coil - CTM, Parker Valve (Replaces 760014 and 760062) CTM / mtm

4 REQUIRED PER DIRECTIONAL VALVE

Pigtail - Parker Valve Coil w/ Female Weather Pack

CTM / mtm

Pigtail - Parker Valve Coil w/ Male Weather Pack CTM / mtm

725029

O-Ring - Parker Valve Mount -

705061

Screw - Long Parker Valve

705062

Screw - Parker Valve (1 1/4” x #10 x 32)

705060

Screw - Parker Valve (1 1/2” x #10 x 32) mtm

760193

Control Manifold - Constant Speed Assembly CTM

760191

Control Coil Only - Constant Speed CTM

760192

Cartridge Only - Constant Speed CTM

740035

Kit - Constant Speed Hydraforce CTM

715191

Controller - Constant Speed w/ Interlocks, Eaton, HFX CTM (2020 & Up)

760195

Controller - Signal Interlock EVDR Module, Driver CTM

715190

ControllerConstant speed Hydraforce CTM (2014-2019)

715192

Harness - Main Constant Speed, w/ Interlocks CTM (2020 - Present)

715193

Harness - Constant Speed, w/ Interlocks, J1939 Controller to Pump & Motor CTM (2020 & Up)

740029

Quad Sensor mtm

740031

Quad Sensor Deutsch CTM

740028

Sensor - 3-Wire, Motor Speed mtm

745415 New Eaton Pump - RH, A-Pad - RE (Electronic)

745209 New Eaton Pump - LH, A-Pad - RE

745202 Eaton Pump Rebuilt, RH A-Pad w/o Control Valves

730110 Hose Kit - Charge Pump Filter Loop (For use with 745419)

725041 Gasket - Parker Pump/Compensator

725043

O-Ring - Parker Pump Compensator

790111

Fender - BridgeKing® and BMV, Poly LH, Red CTM / mtm

790110

Fender - BridgeKing® and BMV, Poly RH, Red CTM / mtm

790107

Fender - BridgeKing® and BMV, Poly LH, White CTM / mtm

790106

Fender - BridgeKing® and BMV, Poly RH, White CTM / mtm

790102

Fender - BridgeKing® and BMV, Poly LH, Black CTM / mtm

790100

Fender - BridgeKing® and BMV, Poly RH, Black CTM / mtm

790108

Fender - BridgeKing® and BMV, Poly LH, Orange CTM / mtm

790109

Fender - BridgeKing® and BMV, Poly RH, Orange CTM / mtm

FOR LATCH CYLINDERS, SEE PAGE 74.

790011

Kit - Axle King Pin Hendrickson (Screw-On

FOR TIE RODS, SEE PAGE 88.

-

790051

Kit - Axle King Pin Hendrickson (Cast Backbone Snap Ring Keeper) CTM /

790055

Kit - King Pin, Watson Chalin (Screw-On

791200 Axle Assembly - Hendrickson CTM

790005 ShockAlignment, 3/4” Bolt CTM / mtm

790006 Shock - BMIII Swivel Eye, 5/8” Bolt mtm

790050

Kit

King Pin Hendrickson BridgeKing® CTM

790010

Kit - Axle King Pin Hendrickson (Bolt-On Cap) mtm

Cap) mtm

mtm

Cap) CTM / mtm

790012 Shim King Pin CTM / mtm

SCAN HERE NEED TO ZOOM IN?

1. Open your camera app on your phone.

2. Hold your camera over the code above.

3. Click on the link that appears on your screen.

4. Zoom in to see the diagram close up!

CURRENT STYLE HENDRICKSON AXLE ASSEMBLY (POST 08/2020)

OLD STYLE HENDRICKSON AXLE ASSEMBLY (PRE 08/2020)

SCAN HERE

NEED TO ZOOM IN?

1. Open your camera app on your phone.

2. Hold your camera over the code above.

3. Click on the link that appears on your screen.

4. Zoom in to see the diagram close up!

791020

Nut - Wheel Spindle, BridgeKing® Axle Hendrickson CTM / mtm

791021

Race - Outer Wheel Bearing, BridgeKing® Axle Hendrickson CTM / mtm

791022

Bearing - Outer BridgeKing® Axle Hendrickson CTM / mtm

791023

Race - Inner Wheel Bearing BridgeKing® Axle Hendrickson CTM / mtm

791024

Bearing - Inner BridgeKing® Axle Hendrickson CTM / mtm

791014

Seal - Axle Oil, Westport Hendrickson CTM / mtm

705362

791236

Knuckle - LH BridgeKing®

Axle, Lower w/ Spindle (Cast)

791237

Knuckle - RH BridgeKing®

Axle, Lower w/ Spindle (Cast)

791238

Knuckle - LH BridgeKing® Axle, Upper (Cast)

791239

Knuckle - RH BridgeKing® Axle, Upper (Cast)

791218

Plate - Lower King Pin, w/ Spindle, LH

791219

Plate - Lower King Pin, w/ Spindle, RH CTM

791215

Plate - Upper King Pin, BK® Axle, w/ Fender Mount, LH or RH

791205

Adjuster - Slack, BK®/ Hendrickson Axle (LH/RH)

791212

Yoke - Auto Slack Adjuster, Hendrickson BK® Axle (w/ Insert)

791201

Chamber - Brake, BridgeKing® Hendrickson Axle

245039

Attachment PlateAxle

705083

Clevis Kit - Air Chamber (Clevis, Pin, Keeper)

791204

Hub Cap - Oil, Hendrickson BK® Axle & Steerable 13.2

792108

Bag - Down, Hendrickson HLR 16K Non-Steerable Tag

791017 GasketFor Hub Cap

791210

Brake ShoesHendrickson CTM /

791230 AssemblyHub and Drum

791231 Drum Only CTM / mtm

792105

Bag - Up, Hendrickson SCT13 Steerable (2002-Current)

792106

Bag - Down, Hendrickson SCT13 Steerable (2002-Current)

TUBELENGTH

791202

Tie Rod AssemblyHendrickson, BK® Axle, Tube Length 57.5”

CTM

791225

Tie Rod Assembly - Round Tube Hendrickson Push, Flat Strap Replacement, Tube Length 58.5”

CTM / mtm

791226

Tie Rod AssemblyBM, Round Tube, Tube Length 59.5”

CTM / mtm

790015

Kit - Stabilizer (Shock) - Hendrickson Steerable Pusher, w/ Flat Tie Rod CTM / mtm

792103

Kit - Pivot Bushing, Hendrickson SC13 Models (w/ Bolts) CTM / mtm

791990

Spring - Bolster, Hendrickson Haulmaxx, 46K (4 per truck) CTM / mtm

791991

Strap Kit - Rebound, Hendrickson Haulmaxx, 46K (2 per truck) CTM / mtm

791992

Progressive Load SpringHendrickson Haulmaxx, 46K CTM / mtm

792107

Tank Kit - Air, Hendrickson 13.2 Steerable w/ U-Bolts CTM / mtm

715525

PendantCTM Rear Pendant Assembly 25’

715533

PendantCTM Rear Pendant Assembly 15’

715505 Pendant -

715524

Pendant - CTM Rear Pendant 25’ for OMNEX Control Mixers

715534

Pendant - Rear Pendant 15’ for OMNEX Control Mixers

715523

Pendant - CTM Rear Pendant 5’ for OMNEX Control Mixers

715530

Pendantmtm Rear Pendant Assembly 25’ mtm

715538

Pendantmtm Rear Pendant Assembly 15’ mtm

715535

Pendantmtm Rear Pendant Assembly 5’ mtm

715526

715506 Cord AssemblyCTM 5’ Pendant

715541

Pendant - mtm, 25’ Weather Pack 1-Wire Start/Stop

715540 Pendant - mtm, 5’ Weather Pack 1-Wire Start/Stop

715546

Pendant - 25’ Weather Pack 3-Wire Start/Stop mtm

715545

Pendant - 5’ Weather Pack 3-Wire Start/Stop

715536 Cord Assembly5’ mtm Pendant mtm

715547

Pendantmtm 25’ Aluminum mtm

715548

Pendantmtm 5’ Aluminum mtm

761018

Deutsch Connector23 Position, Receptacle CTM / mtm

761030

Deutsch Connector - 23 Position, Harness Side Rear Pendant CTM / mtm

715549

Plug - Jumper, CTM Rear Pendant, Wireless CTM

761045

Deutsch Connector - 21 Position, Main Harness Side CTM / mtm

761028

Deutsch Connector - 21 Position, Cab Box (C52 Connector In-Cab Box) CTM / mtm

715515

Repair Harness CTM Rear PendantHarness Side (Includes Deutsch Connector 18”) CTM

715516

Repair Harness mtm Rear PendantHarness Side (Includes Deutsch Connector 18”) mtm

761019

Housing - Deutsch MaleRear Pendant Cord CTM / mtm

761057

Nut Strain Relief - Deutsch, Pendant Cord CTM / mtm

761056

Strain Relief - Deutsch, Housing Only CTM / mtm

765009

O-RingRear Pendant CTM / mtm

ADJUSTABLE, RAM ARM, DASH-MOUNTED DISPLAY

CHUTE LOCK, CHUTE HAZARD, & HOPPER UP WARNINGS

HYD FAN COOLING ICON WITH BUILT-IN ON/OFF OVERRIDE ON SCREEN

TACHOMETER INDICATOR FOR DRUM RPM & DIRECTION

DIGITAL HYDRAULIC TEMPERATURE & PRESSURE DISPLAY GAUGES

RESETTABLE AND LIFETIME DRUM COUNTER

BUILT-IN REAR VIEW/SAFETY CAMERA INTEGRATED ON SCREEN

AUTOMIX COUNT & RESET FUNCTIONS

JOYSTICK COMPLETE CONTROL IN THE PALM OF YOUR HAND

SUPERIOR ERGONOMIC DESIGN FOR COMFORT & SMOOTH OPERATION

UNLIMITED SET-UP POSITIONS FOR DRIVER PREFERENCE

FLEXIBLE JOYSTICK CONTROLLER FOR ALL PRIMARY JOB SITE FUNCTIONS

ALL BUTTONS ARE LOCKED OUT IN TRANSIT EXCEPT DRUM START / STOP SO OPERATOR CANNOT ACCIDENTALLY ACTIVATE FUNCTIONS

COATED, FLEXIBLE ROD ARM WITH LASTING, DURABLE LIFE EXPECTANCY

AUTO MIX FUNCTIONS

AUTO MIX RANGE (60 - 150 REVS)

THE AUTO MIX FUNCTION WILL RAISE THE VEHICLE ENGINE RPM IN A CHARGE POSITION UNTIL A PRESET DRUM REVOLUTION IS ACHIEVED. AFTER THE AUTO MIX ACTION IS COMPLETE, THE CONTROLS WILL GO INTO A CONSTANT SPEED (DRUM SAVER FEATURE) IN THE CHARGE POSITION.

7” LCD COLOR SCREEN & KEYPAD CONTROL FEATURES

7” LCD COLOR SCREEN

715682

Switch - Push, Elite Joystick,

715690

715688

715683

Switch - Push, Elite Joystick, Green LED, Charge,

Button - Switch, Elite Joystick, Green, Charge,

715689 Button - Switch, Elite Joystick,

715681

SwitchPush, Elite Joystick

715691

Button - Switch, Elite Joystick, Chute Up / Down

715680

Switch - Push, Elite Joystick, Hopper, Gen.

715686

Button - Switch, Elite Joystick, Black, Charge

•

•

•

•

•

•

•

• Charging

• Battery

SPLIT TANKS

WATER TANKS (BY SIZE / MATERIAL)

765222

Tube - Water Tank Sight Gauge

125 Gal Poly, LH CTM / mtm

765223

Tube - Water Tank Sight Gauge 125 Gal Poly, RH

765225

Tube - Water Tank Sight Gauge

150 Gal Poly, LH CTM / mtm

765224

Tube - Water Tank Sight Gauge

150 Gal Poly, RH CTM / mtm

765232

Poly Water Tank Floating Ball CTM / mtm

POLY WATER TANK SYSTEM BENEFITS

1. Safer, non-pressurized poly water tank utilizes air operated water pump

2. Dual diaphragm pump capable of up to 90 psi water pressure at rear of mixer

3. Increased water pressure equates to more thorough, more efficient (quicker) wash downs

OEM Con-Tech Manufacturing, Inc. & WILL FIT mtm MIXERS

4. Poly water tank is more resistant to environmental damage (i.e. rust, corrosion, scale, paint chipping, etc.)

5. Wall thickness and material composition unmatched in the industry

6. Uses standard flopper seal with “thru-bolts” on flange

7. Replaceable, common “ag type” threaded adapter fittings are readily available

8. Tank head contains molded grab handles, eliminating the need for additional bolt-on components

9. Dual sight gauge tubes increase viewing angle to front/rear of mixer in cross-mount applications

10. Large rubber sight tube resists damage from impact or freezing and has large, easy-toread scale

11. Integrated sight tube minimizes the need for numerous attaching parts

12. Tank does not require surface coating

13. Replacement cost of poly tank is considerably less than “weight similar” aluminum

FOR OVERHEAD WATER TANK ASSEMBLIES AND COMPONENTS, SEE PAGES 120-121.

CTM High Overhead Water Tank

200-GALLON ASSEMBLY

400-GALLON ASSEMBLY

205207

Support - Fender, Rear, LH, Poly

Support - Fender, Rear, RH, Poly Fender, Rail Mount

205196

Support - Fender, Front, LH, Poly Fender, Rail Mount

205197

Support - Fender, Front, RH, Poly Fender, Rail Mount CTM /

205247 Bracket for Poly Fender

205249

- Poly Fender,

705336 Bolt Kit - Steel to Poly Fender

205240

Support Plate - Drop Fender, Under Rail, Weld-On

705058

Carriage Bolt - 3/8” x 1 1/4”, Fender Support Mount

705079

Lock Nut - 16 UNC, Flange Head

- Rubber Cushion, Radius, Poly Fender

REPLACEMENT FENDERS

245366 Plate LH Bottom MountBMV Fender, Gen. II

245364 LH Fender MountGen. II mtm 790103

790110

Fender - BridgeKing® and BMV, Poly LH, Red CTM / mtm

790107

790106

Fender - BridgeKing® and BMV, Poly RH, Red CTM / mtm

Fender - BridgeKing® and BMV, Poly LH, White CTM / mtm

Fender - BridgeKing® and BMV, Poly RH, White CTM / mtm 790102

790100

Fender - BridgeKing® and BMV, Poly LH, Black CTM / mtm

Fender - BridgeKing® and BMV, Poly RH, Black CTM / mtm

/ mtm

790109

507-374-2239 139 CHUTES HOPPERS & COLLECTORS PEDESTALS AIR SYSTEM HYDRAULICSAXLESCONTROLS RESERVOIRS & SLUMP METERS WATER SYSTEM FENDERS & BUMPERS DRUM PARTS ELECTRICAL ACCESSORIES & TOOLS WASHOUT SYSTEM DECALS & PLACARDS MADE IN THE USA. RESOURCES FENDERS & BUMPERS

285710 Bumper - Kenworth W900, 2015, Set-Forward Front Axle

285712 Bumper - Kenworth T880, T800 Set-Back (2015 to Present)

285885

- 2017 Kenworth T880 Set-Forward

285260

- Peterbilt 365 (2009)

285002 Bumper - RD Mack CTM / mtm

286222 Bumper - Mack, Front, GU, 2007-2020/Current CTM / mtm

285259 Bumper - Mack Granite CTM / mtm

286239 Bumper - Western Star, Front CTM / mtm

285747 Bumper - Freightliner (114 SD) CTM / mtm

285140 Bumper - Sterling CTM / mtm

285036 Bumper - IH 5000 CTM / mtm

285037 Bumper - IH 5500 CTM / mtm

705105 Bolt Kit - Adj. Bumper, Fully Adj. Mount

705106

Bolt Kit - Adj. Bumper, Fixed Mount

245378

Bracket - Rear Recovery Plate / Adj. Bumper Mounting, LH BK® CTM

Recovery Plate / Adj. Bumper Mounting, RH BK® CTM

Adjustable Rear Bumpers

245375

Angle - BK® Bumper Mount, Adjustable, LH CTM

285985

ChannelRear Bumper Bar

245379

Bracket - BridgeKing® Adj. Bumper, Bar to Mount Arm CTM

OEM Con-Tech Manufacturing,

& WILL FIT mtm MIXERS

The New Standard.

THE CON-TECH® HIGH PERFORMANCE™ DRUM

New! Tail Cone Fin Hole Configuration with Elevated Surge Fins: Limits buildup, improves mixing and reduces wear

High Performance Tail Cone: Special fin spiral with an additional 1/4 turn allows for unmatched charging speed and discharge performance

Patented A.R. Steel Lip Doubler: Doubles fin thickness for ultimate wear protection and fin life

EcoFin Technology: Reduces wear and buildup while improving mix consistency

Precision Fit Panels: Eliminates flats spots that cause accelerated wear areas — Ensures optimal fin position for even, smooth pours

High Capacity Mixing Bowl: 25% increase in mixing area with a lower center of gravity for improved stability

Ball Buster Paddle System: Drastically reduces or eliminates cement balls

Fabricated A.R. Steel Head: 1/4” true nominal thickness reduces wear areas throughout

One-Piece Solid Roller Track: Pre-machined and crowned — Eliminates weld cracking and increases structural integrity over hollow designs

5/16 Hatch Frame with Tapped Holes: Increases frame thickness by 85% and eliminates square-welded nuts

Straight Taper Cone: Straight angle from the belly to the drip ring eliminates surging caused by non-straight cones in a high-production pour

Removable Lifting Lug: For easy and safe drum removal and replacement — a removable lifting lug is included with each HP drum

Inc.

Light - Back-Up White LED, 4” AMP Plug CTM / mtm

715855

Light - Red LED, 4” STT, AMP Plug CTM / mtm

715057

Light - Red LED w/ Back-Up, 4” STT, AMP Connector CTM / mtm

715859

Light - Peterson Amber LED, 4” Strobe, AMP Connector CTM / mtm

715853

Light - Amber LED Round, 2.5” w/ Reflex Lens, AMP Plug CTM / mtm

715854

Light - Red LED Round, 2.5” w/ Reflex Lens, AMP Plug CTM / mtm

715294

Light - Red LED Round, 2.5” STT, 3-Wire AMP Plug CTM / mtm

715856

Light - Amber LED Round, 2.5” Strobe, AMP Plug CTM / mtm

715304

PigtailAMP Style, 2-Wire CTM

715303

Pigtail - AMP Style, 1-Wire (For Integrated Back-Up Lamp in 715057) CTM / mtm

715295

PigtailAMP Seal, 3-Wire CTM / mtm

715038

Pigtail - Strobe (For use with 715859 only) CTM / mtm

715182

HarnessSTT w/ Amp Seal CTM

715183

Harness - Fender Front w/ Amp Seal CTM

715155

HarnessFender Extension CTM

715286

Harness - BridgeKing® Rear Bumper, Stop, Tail, Turn and Reverse, Amp Seal CTM

715710

Harness - 2.5” Strobe/STT, LH Upright CTM

715711

Harness- 2.5” Strobe/STT, RH Upright CTM

715181

Harness - Tri Bar w/ Amp Seal CTM

715138

Lic. Plate

Harness CTM Main Chassis, MTM, BM, 02-06 mtm

715115

HarnessBridgeKing®, Main CTM

715116

HarnessBridgeKing® Trailer CTM

The Armor-Tech™ Wiring System is the perfect example what we can accomplish by listening to our customers. The number one trouble area on a mixer is a poor connection from the front pedestal to the rear.

Con-Tech solved the connection problem, and in the process, found a way to make maintenance, troubleshooting, diagnosis, replacement, and repair easy.

715270

Harness Set

(Orange, Green, Red) CTM

Easy access for repairs and maintenance

We don’t believe in digging through the cab for electrical issues. Our mixers use simple and reliable Deutsch bulkhead connectors to tether each independent coil from the front pedestal to the back. Each assembly is easy to identify, troubleshoot, and most importantly, reach.

Color-coded, independent harnesses

Each cable has independent duties. In the event of a malfunction or damage to a line, our cables can be replaced individually. This simple approach ensures the communication between pedestals is interrupted less frequently and for less time. We don’t believe in replacing the whole harness.

Built for harsh conditions

Our system is UV, chemical, and concrete build-up resistant rubber jacketed cables. Unlike our competitors, we use basic, balanced, proven components to make sure we keep your mixer running at it’s best at all times.

Protects your bottom line

This technology is representative of our philosophy at ConTech. We don’t charge extra for our best ideas - we include our proprietary technologies in our builds because they make our trucks the most affordable and efficient in the industry.

Rear Pendant Controls

WILL SAVE YOU TIME, MONEY, AND HEADACHES.

MADE WITH THE PRODUCER IN MIND

THE CON-TECH® EcoWash™ WASHOUT SYSTEM IS LEADING THE CHARGE FOR COMMON SENSE SOLUTIONS IN YOUR OPERATION.

1 SAFETY

Keeps your drivers working on the ground

• Designed to minimize and eliminate the need for drivers to climb up and down ladders to wash out

• Four strategically-placed, internal spray zones on the rear pedestal and drum

• Control valves located on the rear pedestal at ground level

2 RELIABILITY

Simplicity purposefully built into the design

• Washout system utilizes manual ball valves to increase reliability and minimize required maintenance

• 100 mesh inlet strainer keeps contamination from entering valves and spray nozzles

• Water drain valve located on strainer for freeze protection

3 EASE OF USE

Straight-forward, reliable, & proven components

• The cycle is powered by a dualdiaphram air pump that supplies up to 100 psi of spray pressure

• In-stock replaceable parts from Con-Tech Parts

• Scan the QR CODE with your phone camera to learn more:

THE HIGH-PERFORMING ECOWASH ™ WASHOUT SYSTEM KEEPS YOUR CREW GROUNDED.

730007

Bar - Drum Sprayer CTM / mtm

730091

Bar - Drum Sprayer Assembly, 2 -Piece CTM / mtm

730000

StrainerSpray Bar CTM / mtm

285437

Mount - Drum Sprayer (Long, 4.67”) CTM / mtm

285438

Mount - Drum Sprayer (Short,3.25”) CTM / mtm

710260 PumpWater Tank (Air)

765208 ValveAdd Water (Electric)

KEEP YOUR MIXERS AT TEMP, CLEAN, & LOOKING THEIR BEST WITH DRUM SPRAYER BARS

The Con-Tech drum sprayer bar is a simple add-on feature that will help keep your concrete temp within spec on those hot days.

• An additional benefit is that it keeps the drum clean and promotes positive company image - keeping your rolling billboard looking it’s best!

• The sprayer bar assembly includes a filter screen to keep the nozzles from clogging (due to scale and contaminants in the water tank) and is turned on/off by a simple ball valve.

• Bar is shaped to follow the contour of the drum and mounts with simple bolt brackets.

776030 U-Bolt Spray Bar

SAFETY DECAL PLACEMENT

NOTES: APPEARANCE OF THE TRUCK, AND THE LOCATION OF THE DECALS MAY VARY.

Standard decals come in English/Spanish combinations unless otherwise indicated - English/French combinations are also available.

*Door decal locations may vary by manufacturer and space availability. If the door does not allow for decal placement, the decals may go on the back wall of the cab.

*All extension chutes should have proper decals on both sides.

SAFETY DECALS MUST BE REPLACED ANY TIME THEY ARE DAMAGED OR MISSING OR CANNOT BE READ CLEARLY.

SAFETY NOTICE OPERATOR’S INSTRUCTION

NOT A STEP

NON-CTM/ mtm PARTS AVAILABLE

OPTIONS

All measurements are to the center of the weld seam.

DIMENSIONS

FIN THICKNESS: 3/16” Standard 1/4” Optional

DRUM SHELL THICKNESS: 3/16” Standard 1/4” Optional

HATCH OPTION: Single Dual Quick

FINISH: Prime Paint

REV DRUM REPLACEMENT: YES NO

All measurements are to the center of the weld seam.

OPTIONS

FIN THICKNESS: 3/16” Standard 1/4” Optional

DRUM SHELL THICKNESS: 3/16” Standard 1/4” Optional

HATCH OPTION: Single Dual Quick

FINISH: Prime Paint

B C

E Measurement E

spans from the top of the lower plate to the top of the upper hoop.

Pedestal A

OPTIONS A

DIMENSIONS

PEDESTAL CHOICE: A B

DRUM OPENING: 42” 46”

HOPPER: Drop Standard

MAIN CHUTE: 5 ft. 6 ft.

ROLLERS: YES NO

LADDER ASSEMBLY: YES NO

Mixer Serial #:

MIXER INFO: CTM mtm

Mixer Serial #:

www. CTMMIXERS .com 180 CHUTES HOPPERS & COLLECTORS PEDESTALS AIR SYSTEM HYDRAULICS AXLES CONTROLS RESERVOIRS & SLUMP METERS WATER SYSTEM FENDERS & BUMPERS DRUM PARTS ELECTRICAL ACCESSORIES & TOOLS WASHOUT SYSTEM DECALS & PLACARDS FAMILY-OWNED. RESOURCES

Pedestal B

*Please be advised we send our invoices via email the date your order ships

I hereby certify that the information contained herein is complete and accurate. This information has been furnished with the understanding that it is to be used to determine the amount and conditions of the credit to be extended. Furthermore, I hereby authorize the financial institutions listed in this credit application to release necessary information to the company for which credit is being applied for in order to verify the information contained herein. All invoices are to be paid 30 days from the date of invoice. There will be a 1.0% interest charge per month on all invoices that are 30 + days past due.