2-1/2” GUNITE JET INSTALLATION INSTRUCTIONS
SPA MASTER™ 2½" JET INSTALLATION
Gunite Jet Body Assemblies include Body, Wall Fitting, & Threaded Ring. PVC Schedule 40 Pipe is not included
INSTALLATIONGUNITE PROCEDURES & PRESSURE TESTING INSTALLATION
& PRESSURE TEST GUIDE
1. Run ties through holes in the Jet Body braces, and attach to the rebar 1. Run tiesPVC through in for jet wall body bracesand andcut attach rebar. 2. Estimate length of 2.5” pipe asholes needed thickness longertothan needed. Glue the 2.5” PVC pipe into the Jet Body. Cap the other of the 2.5” pipe for 2. endEstimate length of pressure 2.5" PVCtesting. pipe as needed for wall thickness. Cut pipe longer than needed. Glue the 3. After the pool is gunited, chip out around pipeend to provide area for the Niche. Cut pipe and glue niche onto pipe. 2.5" PVC pipe intothe jetwall body. Capthe other of 2.5”enough pipe for pressure testing. 4. Glue the Threaded Ring onto on end of the 1” pipe. Lubricate the o-ring on threaded ring. Insert the threaded ring end of this assem3. After pool gunite work is complete, chip out wall around pipe to provide enough area to glue on bly inside the 2.5” PVC and thread clockwise into jet body until tight. Make a mark on the 1” PVC pipe that is flush with the end of the niche. Cut with wall andthis glue niche onto pipe. niche or the inside face of thepipe deepflush dish niche. Remove assembly from the jet body by turning counter-clockwise. 4. length Glueofthe ring onto one 3.5” endback of the 1” the PVCmark pipe. pipe yet. Lube the o-ring 5. Shorten the thethreaded 1” PVC pipe by measuring from onDo the not pipecut and1"cut. Glue wall fitting onto the cut end. Lube o-ring on threaded Tighten withInsert gunitethe jet tool. Pressure testing water line can now be done by threading gunite jet on the ring. threaded ring. threaded ring end the of this assembly inside the 2.5” PVC andthe thread tool into the wall clockwise fitting until into tight.jet body until tight. Make a mark on the 1” PVC pipe that is flush with the end of the 5. Choose the desired jet face internal and the desired Jet Orifice. Thread jet internal into wall fitting until tight.
niche or inside the deep dish niche (see below), then remove this assembly from jet body by turning counterclockwise. NOTE: DISTANCE BETWEEN THE END OF THE NICHE AND THE 1” PVC PIPE MUST BE 3.5” 5. Shorten the length of the 1" PVC pipe by measuring 3.5” back from the mark on the pipe and cut. Glue wall fitting onto this cut end. Lube o-ring on threaded ring, if needed, add teflon tape Sizes onto threads Power Jet Orifice and insert this new assembly back through the 2.5” PVC pipe and thread clockwise into jet body. 5/16” - 10GPM Tighten with Gunite Jet Tool. Pressure testing can now be done by threading the3/8” Gunite Jet Tool into - 13GPM 7/16” - 17GPM wall fitting until tight. 1/2” - 22GPM 6. Choose desired jet face internal. Thread jet internal into wall fitting until tight. 4” Directional 25591-210-000
4” Roto 25591-220-000
4” Pulsator 25591-230-000
4” Massage 25591-240-000
4” Twin Spin 25591-250-000
Power Jet 25582-000-000
VISIT WWW.C-M-P.COM FOR INTERNAL OPTIONS
Holes for ties Note: Lube O-Ring Prior to Installation
Jet Internal Wall Fitting
Niche (sold separately) Regular: 25580-000-090 Deep Dish: 25380-900-090
Threaded Ring
MASTER™ SPA SYSTEMS ¦ 2½ GUNITE / FIBERGLASS JETS SPA
25580-000-000, 4in Gunite Jet Body Assembly (2in Slip x 1.5in Slip x 2.5in Slip) 25580-090-000, 4in Gunite Jet Body Assembly (2in Slip x 1.5in Slip x 2.5in Slip) with Niche 25581-000-000, 4in Gunite Jet Straight Body Assembly [1.5in Spg/1in Slip x 1in Spg/1/2in Slip) 25581-090-000 4in Gunite Jet Straight Body [1.5in Spg/1in Slip x 1in Spg/1/2in Slip) with Niche
2” S Water x 1-1/2” S Air Jet Body Assy 25580-000-000
Jet Tool & Pressure Test Plug 25590-000-000 Steel Rebar
3.5” 1-1/2” Spg x 1” Slip Water 1” Spg x 1/2” Slip Air Jet Body Assy 25581-000-000
9” Minimum Distance 0414sb
Deep Dish Niche: CUSTOM MOLDED PRODUCTS | 36 HERRING ROAD, NEWNAN, GA 30265 | WWW.C-M-P.COM Measure from this point 1" Pipe
800.733.9060 | WWW.C-M-P.COM
105