Page 1

Soak Cordura PREMIUM CORDED FABRIC WALLS www.anutone.com/fabrics.htm

0 01 ! 2 o r fo er

Z ew N ize S

Soak Cordura Brochure Release 1.2 December 2009


Soak Cordura Visual Variants

Key Attributes Anutone premieres the all-new Soak Cordura for 2010 and beyond ... bringing Size Zero in fabric-wrapped panels to interior spaces! Panels can be as slim as 10mm and hung on walls to be accessed at any point. No longer do Soak panels need to W NE be bulky and be accessed from one corner onwards. Soak Cordura features corded non-wovens that offer contemporary colours for classy interiors and brings • productivity and privacy of modern workplaces • demanding performance of special venues like auditoria Added feature is high impact resistance, making Soak Cordura rugged and durable for any interior use.

Typical Applications Soak Cordura is used for wall panellings and combo partitions in architectural spaces listed below. See page 7 for details. -

office conference rooms, meeting rooms auditoria cinema multiplexes classrooms & libraries hotel banquet halls & corridors studios home theatres

The visual variants of Soak Cordura are realised from orientation of the fabric colours. The fabric colours can be installed in singles or double combos - pastels, darks or contrasts. Current standard fabric colours include: (See page 4) • Calypso • Skye • Porcelain • Simba • Spearmint • Sanz • Blaze • Lime • Wasabi • Avocado • Jade • Myst

Design Considerations •

The longer edges of the panels can be oriented horizontally or vertically to make a space look visually longer or taller.

Indicated panel thickness is for base panel only. 3 mm of fabric thickness and 5 mm of Z-Clip or H-Spline system should be added to overall Soak thickness. Hence, 10 mm panel means 18 mm system thickness post-install. For true 10mm only go for Slim PNS or Slim Compo!

Panels should not touch the floor but rest on Sonator wooden skirting which may be repeated at the wall-ceiling junction.

Panels must be fitted in modules that are dimensioned in multiples of 600mm to avoid field cutting.

Aesthetics Fabric walls with neat panel joint lines, vertically and horizontally, for a true panel effect. The edge profile is pencil radius due to the fabric lamination. Soak Cordura features the ‘ribbed’ look.

Product considerations

Features

Additional Features

• • • • •

Volume density (base panel) - 400 kgs/m3 Sizes - Width 600mm; Lengths 1200 for 10mm & above, 2400mm for 20mm & above Thickness (base panel, add 8mm for system thickness) - 10 / 15 / 20 / 25 / 30 / 40 / 50mm Edge profiles - Square for 10 & 15mm thickness; Square with long edges kerfed for H-spline for 20mm & above Fabric returns - Fabric is returned and bonded along all edges for 10 & 15mm. Fabric is returned and bonded along the short edges and returned and bonded upto the H-spline groove for the long edges for 20mm & above.

2

Soak Cordura offers and additional and useful feature of tackable surface for pin-ups.

Accessibility Soak Cordura 10 & 15mm thick with Z-Clip for any point accessibility. 20mm & above with H-Spline for corner point accessibility ensure easy dismantling and reinstallation.

Environmental Impact Soak Cordura is an eco-friendly product and wins GBC’s 15 LEED points for green buildings, a ‘Sustain’ effort from Anutone®. NRC for 20mm

Accessories Mounting Standard A C25 Others D25 D50 C50

Fabric shade may vary from batch to batch due to limitations in dye technology. Butt jointing of different batch numbers is not recommended.

System accessories

Cordura

H-Spline A + Strut™ CC25 + Synth™ AW 10x25

0.50 0.78

A + Strut™ CC25 A + Strut™ CC50 A + Strut™ CC50 + Synth™ AW 10x50

0.63 0.72 0.90

W NE


Technical Variants Variants by Substrates Anutone's unique AcoustCombi™ technology, variable sound absorption, is realised from substrate variants • Soak Strand Cordura – base panel natural surface for mid and high frequency sound absorption for all applications • Soak Burl Cordura – blinded surface suitable for lowfrequency sound absorption and high-frequency sound reflection for for variable acoustics and extended bass response in banquet halls, auditoria, cinema, studios, home theatres etc The AcoustCombi technology works very well with Size Zero panels of Soak Cordura.

Variants by Core (does not apply to Size Zero) For Noise Isolation, technical variants are realised from the core material - the Soak Septum Series – •

Soak Septum Cordura

Soak Septum T1/T2/T3 Cordura

in all applications where sound absorption and noise isolation is required, especially offices, studios, home theatres etc Variants by Density (does not apply to Size Zero) Anutone's unique VDH technology - Variable Density Hybrid - is available in Soak Cordura. This allows for space-saving A-mounting of panels but with AutoAir - an automatic airgap for an acoustic infill of Synth for additional sound absorption. Panel size is restricted to 600x1200x25mm on H-Spline only. Applications include offices, home theatres where more sound absorption than that provided by regular A-mounted Soak Strand Cordura is needed. Now Size Zero makes VDH and AutoAir redundant in certain application. Strut CC10 with Synth 10x10 provides a slim backer to Soak Cordura 10 & 15mm thick panels.

Tech Performance - Fabric

Tech Performance - Base Panel •

Non-combustibility - Mass loss 53% @ 750 C - ISO 1182

Ignitibility – ‘P’ - BS 476 Part 5

Fire Propagation Index – 5.17 - BS 476 Part 6

Surface Spread – Class I - BS 476 Part 7

Specific Optical Density of Smoke

Thermal Conductivity – 0.08 Wm/k - IS 3346

Base panel conforms to EN 13168 2001.

o

- Flaming Exposure 26.28 Dm (Corr) - ASTM E662

Logistics - Panel Thk (mm) Nos./carton Carton wt (kgs) Carton ht (mm) 10 10 40 165 20 06 44 165 25 06 54 175 40 04 60 175 50 03 51 165 Note - Carton size 1216 x 616 mm. Carton weight is for Soak Strand Cordura only. Soak VDH Cordura will be lighter. Soak Burl Cordura will be heavier. Minimum order quantity - 1 carton.

Flammability Test Results as per AS1530 Part 3 • Spread of Flame (Index 0-10) 0 • Smoke Developed (Index 0-10)3 As per AS/NZS 3837 • Group Number 1 - Avg Specific Extinction Area 49.7m2/kg Flammability Test Results as per BS476 • Part 5 - Ignitibility – ‘P’ • Part 6 - Fire Propagation Index – 3.1 • Part 7 - Class 1Y

Economics Soak Strand Cordura 10mm thick with Z-Clips or 20mm thick on H-Spline is techno-commercially economical for the lifecycle cost of the system.

Warranty 10 years limited warranty - on the assembled system when installed to Anutone’s specifications and maintained as per instructions.

3


Visual Variants

STOCK

CUSTOM

Standard fabric shades with short lead times.

Custom fabric shades with longer lead times.

Calypso

Avocado

Lime

Sanz

Simba

Skye

Jade

Wasabi

Stately

Silhouette

Nautilus

Aubergine

Blush

Clay

Chilli Red

Koala

Theatre

Silver

Lightsout

Octane

Cinder

Bark

Blaze

Spearmint

Porcelain

Myst

Fabric Features Fabric is a non-woven, needle-punched, chemically-free, thermally-bonded, multi-purpose acoustical fabric that is highly durable with exceptional performance. It has been specially developed for the Soak series by Anutone in association with Autex of New Zealand. All fabric information in this brochure is based on data by Autex.

4

100% polyester

Does not fray or zipper when cut

Safe, non-toxic

12 stock and 14 custom colours

Recyclable, environmentally-friendly

NRC 0.20 when directly adhered to hard walls

UV stable - resistant to fading

Density 400 gsm

Moisture-resistant - rot-resistant, stain resistant

Thickness 3mm

Durable - infinite product life

Manufactured to ISO 9001 protocols


Installation Drawings

Soak Cordura 20mm thick - ‘C22’ mounting installed on Strut CC22 H-Spline fitted in long kerfed edges - with Synth 10x25 backing

Soak Cordura 10mm thick in dual tone - ‘A’ mounting installed directly on wall (no airgap) - Z-clip on panel and double clip on wall

Soak Cordura 10mm thick in dual tone - ‘C10’ mounting installed on Strut CC10 - Z-clip on panel and double clip on wall - with Synth 10x10 backing

5


Acoustical Parameters Sound Absorption Coefficient as per ISO 354 Frequency (Hz)

1 0.9

Infill-Synth 125

0.8

10x10

0.25 0.50 0.69 0.87

0.68 0.60

0.70

10x25

0.26 0.53 0.71 0.93

0.76 0.59

0.75

0.7 0.6

250

500 1000 2000 4000 NRC

0.5 0.4

10x10

0.3

10x25

NOTE - Anutone has the capability, expertise and own infrastructure to perform custom acoustics tests for given design as per ISO 354 at its Scans lab and provide acoustic values of Soak Cordura specific to installations, a private sector first in South Asia.

0.2 0.1 0 125

250

500

1000

2000

4000

Soak Cordura - 20mm thick kerfed edges joined with JEH Spline, mounted on Strut CC25

Site Considerations •

Cartons of Soak Cordura must be stored on a flat, dry surface.

They must not come in contact with water.

Wall surfaces must be devoid of moisture prior to installation.

The final act of panel installation must be performed only when all other works are completed and site has attained occupancy conditions in terms of room temperature and humidity.

Trained and skilled technicians must install Soak Cordura. ‘Soft’ and ‘clean’ handling is a must. 10 & 15mm thick panels are fragile and require very careful handling.

For wall edges and corners where cut panels are required, the fabric can be peeled back and cut to size, the base panel cut to size and fabric bonded again with rubber-based adhesives.

Panels can be nylon brushed and/or vacuumed post-installation.

Applied Acoustics Anutone’s Selec programme makes it easy for architects, consultants, contractors and clients to apply Soak Cordura to architectural spaces. System selection of Soak Cordura is suitable for but not limited to the following spaces.

OFFICES Conference Rooms / Training Rooms / Meeting Rooms Spec

Ambient RC (N)

Vibration Curve

Reverb Time seconds

Sound Level dBA

Freq Resp Hz

Speech RASTI

40

I

1.0

60

White

>0.4

Pax 1

Acoustics2

NRC/STC3 Mtg4 Ods5

Panel

Framework

Infill

<25

Absorption

Fair

A

18

Soak Strand 10mm

Z-Clip/Bar

Nil

25-50

Absorption

Medium

A

30

Soak VDH 25mm

H-Spline

Synth 10x10

>50

Absorption

Good

C10

23

Soak Strand 15mm

Strut CC10 Z-Clip/Bar

Synth 10x10

<50

Absorption & Fair Isolation Good

A

25

Soak Septum 20mm

H-Spline

Nil

Notes: Where sound absorption and noise isolation is required between rooms, then system selection must be made from the Soak Septum Cordura series with assistance from Anutone or better still, independent acoustical consultants.

6


AUDITORIA AND CINEMA Ambient RC (N)

Vibration Curve

Reverb Time seconds

Sound Level dBA

Freq Resp Hz

Speech RASTI

Auditoria

30

H

1.2-1.5

95

50-20k

>0.6

Cinema

30

H

0.7

105

40-20k

>0.6

Spec

Pax1

Acoustics2

NRC/STC3 Mtg4 Ods5

Panel

Framework

Infill

<150

Absorption

Fair

A

23

Soak Strand 15mm

Z-Clip/Bar

Nil

150-500 Absorption

Medium

C25

47

Soak Strand 20mm

Strut CC22 H-Spline

Synth 10x25

NA

Absorption

LF Good

C25

47

Soak Burl 20mm

Strut CC22 H-Spline

Synth 10x25

>500

Absorption

Good

C50

75

Soak Strand 20mm

Strut CC50 H-Spline

Synth 10x50

Notes: For variable sound absorption that includes LF-absorption and HF-reflection the system selection must include Soak Strand Cordura and Soak Burl Cordura with assistance from Anutone or better still, independent acoustical consultants.

STUDIO AND HOME THEATRE Ambient RC (N)

Spec

Vibration Curve

Reverb Time seconds

Sound Level dBA

Freq Resp Hz

Speech RASTI

Studio

20

F

0.4

95

40-20k

>0.6

Home Theatre

25

G

0.7

90

50-20k

>0.6

Pax1 Acoustics2

NRC/STC3

Mtg4

Ods5 Panel

Framework

Infill

<5

Absorption

Fair

A

25

Soak Strand 20mm

H-Spline

Nil

<5

Absorption

Medium

A

30

Soak VDH 25mm

H-Spline

Synth 10x10

5-10

Absorption

Good

C25

47

Soak Strand 20mm

Strut CC22 H-Spline

Synth 10x25

NA

Absorption

LF Good

C25

47

Soak Burl 20mm

Strut CC22 H-Spline

Synth 10x25

<50 NA

Absorption & Fair Isolation Good

A

25

Soak Septum 20mm

H-Spline

Nil

Notes: For variable sound absorption that includes LF-absorption and HF-reflection the system selection must include Soak Strand Cordura and Soak Burl Cordura. Where sound absorption and noise isolation is required between rooms, then system selection must be made from the Soak Septum Cordura series. This may require assistance from Anutone or better still, the expertise and experience of independent acoustical consultants.

1 Pax - Occupancy - number of persons and corresponding volume of the space 2 Acoustics - Acoustical performance required - Sound Absorption or Noise Isolation or both 3 NRC/STC - NRC is Noise Reduction Coefficient and related to Sound Absorption; STC is Sound Transmission Class and related to Noise Isolation 4 Mtg - Mounting - Panel mounting on base surface as per ISO 354 and/or ASTM E795 5 Ods - Overall depth of system - from base surface to panel surface, installed and finished 7


Installation Guidelines - 20mm on H-Spline

STEP 1 & STEP 2 Mark location of each panel on wall for Amounting (or on Strut CC10/22/50 for C or Dtype mounting), to determine panel usage, position and inside/outside corner details. Install Sonator wooden skirting at base of wall for panel support. Make sure it is level. Height of skirting depends on architectural requirements, usually 150 mm.

STEP 3 & STEP 4 Position first panel, using level to assure plumb. Insert first H-spline section into groove on panel long edge and against wall. Start at top of panel. Spline should be suitably attached to the wall so that it is firmly in place. Add splines down to rest of the panel till the Sonator wooden skirting, making sure plumb is maintained. STEP 5 Position next panel on wall and slide it against first H-spline until they fully engage in the groove. Fix Hspline to opposite edge groove and to wall as done with first panel. Continue procedure along wall length, checking plumb of each panel. NOTE : If a cut Soak Cordura panel is needed to fill inside corner, do not fasten the last row of H-splines to wall. STEP 6 Measure space from last panel to corner at top, middle and bottom of area. Transfer these measurements to the face of the panel. Place panel, fabric side up, on smooth and clean surface and using hand or power saw, cut through fabric and panel so that cut edge is the edge that will fit in the corner.

8

STEP 7 Apply adhesive to back of last full panel along open H-spline that will be used in that edge, (See B), and to back of cut panel, (See C). Insert the last attached H-spline. Insert Hspline with adhesive into other groove of last full panel. Insert groove of cut panel into the H-spline and insert cut edge into corner. Then apply pressure at joint between panel (See D), until contact is made with the wall. Hold until adhesive sets. Secure cut corner panel to wall with four finishing nails along outside edge of panel at corner. Space them evenly and drive at 450 angle. A new, full panel should be used as the first panel after the corner (See E). Butt it against front of cut corner panel after putting adhesive along the length of the panelâ&#x20AC;&#x2122;s thick edge. Continue down this wall (Steps #1 through #5). STEP 8 Measure space from last full panel to corner at top, middle and bottom. Add 50mm, to these measurements. Transcribe these measurements to face of panel to be cut. Place panel, fabric side up, on smooth and clean surface, using hand or power saw, cut through the fabric and panel along the marked line. STEP 9 Gently peel fabric back 75mm from cut edges of both panel pieces. Draw a line on the Soak Cordura panels of both pieces 50mm back from the cut edge, and parallel to the cut edge along the length of the panel. STEP 10 Making sure the fabric is folded back out of the way, cut off this 50mm wide strip of the base panel on both pieces. Remove any loose fibres that may remain.

STEP 11 On one piece, apply hot melt glue to the panel along the 25mm wide exposed top where the material was peeled back, along the cut edge, and along a 25mm wide strip on the back next to the cut edge. Wrap fabric back over face, around edge, and over back so it adheres, stretch tight, eliminating any folds or creases. Repeat procedure with other panel piece. STEP 12 On panel cut to fit corner width, apply adhesive to Soak Cordura panel along the length of the panel, just beyond fabric along the cut edge. Place panel on wall and slip it into the last installed H-spline. Hold until adhesive sets. STEP 13 Apply adhesive in same manner to other panel piece. Position it on wall around corner so it completely overlaps end of other corner panel. Slip H-spline into the groove in the opposite edge and continue downward in the same manner as previously.

H-Spline System


Maintenance Soak Cordura range of products are extremely durable and require little attention to maintain their good looks. Light vacuuming on a regular basis will prevent dust build up and most marks can be cleaned with a mild detergent solution followed by rinsing and blotting. Stains should be dealt with according to the chart below. •

Before carrying out a proposed cleaning method, apply to a concealed section to ensure it will not affect the adhesive or wall covering Avoid severe abrasion Vacuum to restore pile, but do not use a stiff brush.

• •

Note: Anutone does not recommend solvent based cleaners on Soak Cordura

Stain

Treatment Guide

Stain

Treatment Guide

Blood

A

Lipstick

B

Burn/Scorch Mark

K

Mildew

C

Chewing Gum

I

B

D

Milk

A

E

Chocolate

B

D

C

Mud

B

C

Cooking Oils

B

D

C

Nail Polish

A

G

Crayon/Colour Markers

B

D

C

Oil

B

D

Drinks (cola, tea, juices, beer etc)

A

C

Paint (water based)

A

C

Dust/Dirt

Vacuum, then J or C

Paint (oil based)

A

H

D

Excrement

B

Sauces

B

C

D

Grass

C

Shoe Polish

B

C

D

Grease

B

D

Urine

A

C

Ink (ballpoint)

D

E

Vomit

A

C

Ink (fountain)

A

C

Wine

A

Add Salt

C

C

C

C

E

C

D

C

C

D C

A

Mop up excess as soon as possible with a sponge or cloth.

B

Remove surplus with a knife edge or appropriate instrument.

C

Sponge with a solutions of carpet shampoo working from well outside the stain in a circular motion towards the centre (this avoids spreading the stain). Sponge afterwards with clean warm water and mop up excess moisture with a clean dry cloth or sponge. Allow to dry then brush gently with a soft brush. If any stain remains, sponge with a solution of one part household bleach to six parts clear water. Thoroughly rinse after treatment.

D

Lightly sponge with household dry cleaning fluid and blot. Apply sparingly, as the substance may have an adverse effect on the adhesive.

E

Sponge with methylated spirits and blot dry.

G

Apply nail polish remover. The nail polish remover should not include lanolin or be of a greasy nature.

H

Sponge with turpentine (or substitute).

I

Freeze with ice cubes and scrape away while cold.

J

Clean with regular extractive carpet cleaner (if possible).

K

Use circular cutter and remove damaged portion. Re-glue new piece into place.

Anutone offers the above recommendations in good faith. However, Anutone cannot be responsible for unsatisfactory results arising from the proposed treatments. Anutone recommends that you contact professional cleaning experts should you require further assistance with the cleaning and maintenance of Soak Cordura.

9


System Specifications Soak Cordura 10mm on wall - A mounting

Soak Cordura 20mm on CC22 - D25 mounting

Scope – Design, Supply, Build of Soak Cordura as designed, manufactured and installed, per approved drawings and W NE specifications, by Anutone Acoustics Limited, an ISO 9001 2008 and 14001 2004 company.

Scope – Design, Supply, Build of Soak Cordura as designed, manufactured and installed, per approved drawings and specifications, by Anutone Acoustics Limited, an ISO 9001 2008 and 14001 2004 company.

Support – Supplied Z-Clips are installed on the panel reverse on cement spots provided. Supplied Double Wall Clips are installed on the wall as marked. For ends the double wall clips are easily cut at site to make them single.

Framework – Strut CC22 fixed at 600mm centres. CC22 must be installed perpendicular in relation to the long edges of the panels. The H-Spline is installed perpendicular to the Strut CC22 and parallel to the long edges of the panel.

Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______ m2; Colour ______ & _______ ; Size 600x1200mm; Thickness 10 mm. Joints and finish – Pencil radius edges, butt-joined.

Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______ m2; Colour ______ & _______; Size 600x2400mm; Thickness 20 mm Joints and finish – Pencil radius edges, butt-joined.

Soak Cordura VDH 25mm on wall - A mounting

Soak Cordura 20mm on CC22 with Synth - C22 mounting

Scope – Design, Supply, Build of Soak Cordura VDH as designed, manufactured and installed, per approved drawings and specifications, by Anutone Acoustics Limited, an ISO 9001 2008 and 14001 2004 company.

Scope – Design, Supply, Build of Soak Cordura as designed, manufactured and installed, per approved drawings and specifications, by Anutone Acoustics Limited, an ISO 9001 2008 and 14001 2004 company.

Framework – H-Spline is installed parallel to the long edges of the Soak Cordura VDH with suitable mechanical fasteners that are anchored firmly to the base surface.

Framework – Strut CC22 fixed at 600mm centres. CC22 must be installed perpendicular in relation to the long edges of the panels. The H-Spline is installed perpendicular to the Strut CC22 and parallel to the long edges.

Infill - Synth AW 10x10 is friction-fitted inside the Soak Cordura VDH. Panels – Soak Strand Cordura VDH _______ m2 & Soak Strand Burl VDH _______ m 2; Colour ______ & _______ ; Size 600x1200mm; Thickness 25 mm. Joints and finish – Pencil radius edges, butt-joined. Soak Cordura 10mm on CC10 - D10 mounting Scope – Design, Supply, Build of Soak Cordura as designed, W manufactured and installed, per approved drawings and NE specifications, by Anutone Acoustics Limited, an ISO 9001 2008 and 14001 2004 company. Framework – Strut CC10 fixed at 600mm centres. CC10 must be installed perpendicular in relation to the long edges of the panels. Z-Clips are installed on the panel rear and Double Wall Clips are installed on the Strut CC10. Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______ m2; Colour ______ & _______; Size 600x1200mm; Thickness 10 mm Joints and finish – Pencil radius edges, butt-joined. Soak Cordura 10mm on CC10 with Synth - C10 mounting

Infill - Synth AW 10x25 is friction-fitted between the Strut CC25 and lightly adhered with Stick S7. Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______ m2; Colour ______ & _______; Size 600x2400mm; Thickness 20 mm. Joints and finish – Pencil radius edges, butt-joined. Soak Cordura 20mm on CC50 - D50 mounting Scope – Design, Supply, Build of Soak NSS as designed, manufactured and installed, per approved drawings and specifications, by Anutone Acoustics Limited, an ISO 9001 2008 and 14001 2004 company. Framework – Strut CC50 fixed at 600mm centres. CC50 must be installed perpendicular in relation to the long edges of the panels. The H-Spline is installed perpendicular to the Strut CC50 and parallel to the long edges of the panel. Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______ m2; Colour ______ & _______ ; Size 600x2400mm; Thickness 20 mm. Joints and finish – Pencil radius edges, butt-joined. Soak Cordura on CC50 with Synth - C50 mounting

Scope – Design, Supply, Build of Soak Cordura as designed, manufactured and installed, per approved drawings and W NE specifications, by Anutone Acoustics Limited, an ISO 9001 2008 and 14001 2004 company.

Scope – Design, Supply, Build of Soak as designed, manufactured and installed, per approved drawings and specifications, by Anutone Acoustics Limited, an ISO 9001 2008 and 14001 2004 company.

Framework – Strut CC10 fixed at 600mm centres. CC10 must be installed perpendicular in relation to the long edges of the panels. Z-Clips are installed on the panel rear and Double Wall Clips are installed on the Strut CC10.

Framework – Strut CC50 fixed at 600mm centres. CC50 must be installed perpendicular in relation to the long edges of the panels. The H-Spline is installed perpendicular to the Strut CC50 and parallel to the long edges of the panel.

Infill - Synth AW 10x10 is friction-fitted between the Strut CC10 and lightly adhered with Stick S7.

Infill - Synth AW 10x50 is friction-fitted between the Strut CC50 and lightly adhered with Stick S7.

Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______ m2; Colour ______ & _______; Size 600x1200mm; Thickness 10 mm. Joints and finish – Pencil radius edges, butt-joined.

Panels – Soak Strand Cordura _______ m2 & Soak Strand Burl _______ m2; Colour ______ & _______ ; Size 600x2400mm; Thickness 20 mm. Joints and finish – Pencil radius edges, butt-joined.

Custom Methodology The installation of Soak Cordura can be custom-designed to specific needs by Anutone to suit specific or special project requirements. The methodology includes the entire value-chain - site evaluation, criteria definition, noise spectra capture, design optimisation, system specs, systems engineering & integration, project management, acoustic testing & site validation. 10


Technical Specifications Sl#

Description

Soak Cordura

1

Thickness (mm)

10 / 15 / 20 / 25 / 30 / 40 / 50

2

Size (mm)

Width 600 / Length 1200 for 10, 15mm and 1200/2400 for >20mm

3

Core

Strand / Synth

4

Nominal Density (Kg/m3)

400 to 500

5

Weight (Kg/m2)

upto 25

6

Edge

Square for 10, 15mm; Square with long edges kerfed for >20mm

7

NRC / STC

Upto 0.9

8

Fire

Class I

9

Moisture Resistance (%)

RH 90

10

Light Reflectance (%)

Colour Dependant

11

Warranty

10 years

12

Installation

10, 15mm on Z-Clip/Bar; >20mm on H-Spline; Strut CC10, CC22, CC 50

13

Colour

12 stock; 14 custom

14

Maintenance

Nylon-bristles brush; Vacuum

Bill of Quantities (BoQ) - 100m2 Sl # Description

Units

Soak Cordura Walls - H-Spline

Size / Edge

mm

Walls - Z-Clip

600x2400 / C25 Mounting 25 mm

600x1200 10 mm

15mm

1

Z - clips on walls

nos.

834

834

2

Z - clips on Panel

nos.

834

834

3

Strut CC22

lm

198

4

Spline

lm

288

5

Stick S7

Ltr

35

6

Synth AW 10x25mm thick

m

100

7

Panels

m

100

100

100

8

Labour

hrs

3

2

2

Estimated Installed Cost / m2

Rs

4,450.00

3,160.00

3,470.00

2 2

lm - Linear meter, m2 - Square meter, Ltr - Litre, LS - LumpSum, hrs - Hours * The above indicated values are very approximate and dependent on several variables. They are for guidance only, and subject to change without prior notice.

References Office

Auditorium

Intel Bengaluru Golden Wood Packer Bhubaneshwar AEPC Haryana Godrej & Boyce Mumbai NHPC New Delhi Tirupur Chamber of Commerce Tirupur

Gaiety Theatre

Studio Simla

Cinema Shree Radha Movie Park

Chennai

Places of Worship Swami Shri Prempuri Ashram Mumbai

INX Studio Nine X Studio

Noida Mumbai

Home Theatre Mr. K.J. Venkatesh Mr. S.P. Kumar Mr. R.R. Ranganathan

Bengaluru Bengaluru Coimbatore

For the latest update on our projects list please visit www.anutone.com/projects or contact Anutone. 11


W NE

More on Size Zero in Soak Cordura

Size Zero is the current fad. Everybody wants it slim, superslim! After Size Zero laptops, smartphones, televisions and ramp models, comes the ultra-slim, ultrachic Soak series of fabric-wrapped wall panels. Soak Cordura earlier had a limitation of minimum thickness, 20mm. This was due to kerfed long edges to receive HSpline. This also resulted in a site problem of panels being able to be dismantled from one corner only. Now to meet the demand from designers for space-saving slimmer panels, Anutone has innovated to result in 10mm thick panels that can be hung on walls and more importantly dismantled from any point. Also all edges are fully finished so panels can be installed discretely as floating islands!

Highlights Feature

Benefits

Ultra-slim, ultra-chic – all edges finished Architect Discrete install - wall island floats

Architect

Space saving – 10mm thickness only

Builder

Economical – slim means less costs

Customer

Frequency response – additional bass

Acoustician

Matching accessories – slim channel & infill

Contractor

Snag-free - single source compatibility

Project Manager

Accessibility – any point dismountable

Facility Manager

ANUTONE INTERIORS (a division of Anutone Acoustics Limited)

www.anutone.com • Bahrain • Dubai • Mumbai

• Budapest • Chennai • Jeddah • Kolkata • Muscat • Nairobi

ISO 9001:2008 CERTIFIED

ISO 14001:2004 CERTIFIED

Anutone is member of • Dammam • Doha • Kuwait • Manila • New Delhi • Riyadh

Anutone® is a registered trademark of Anutone Acoustics Limited. Specs are subject to change due to continuous improvement programmes at Anutone ®. Contents under copyright registration. No part of this brochure may be reproduced, stored in a retrieval system, scanned or transmitted in any form or by any means electronic, photocopying, recording or otherwise, without the prior written permission of Anutone®.

Document # 909010-500

231, 7th Cross, Indiranagar 1st Stage, Bengaluru 560 038, India Phone +9180 2520 3114 Fax +9180 2520 3115 info@anutone.com

Soak Cordura Brochure  

Z e r o ! PREMIUM CORDED FABRIC WALLS www.anutone.com/fabrics.htm S i z e N e w Soak Cordura Brochure Release 1.2 December 2009

Read more
Read more
Similar to
Popular now
Just for you