Page 1


MAINTENANCE SAFETY WARNING

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow W-2003-0903 instructions can cause injury or death.

Safety Alert Symbol: This symbol with a warning statement, means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

CORRECT

CORRECT

CORRECT

B-10731a

B-12365

B-7469

Never service the Bobcat SkidSteer Loader without instructions.

Use the correct procedure to lift or lower operator cab.

Cleaning and maintenance are required daily.

WRONG

WRONG

WRONG

B-11799

B-15231

B-15280

Have good ventilation when welding or grinding painted parts. Wear dust mask when grinding painted parts. Toxic dust and gas can be produced. Avoid exhaust fume leaks which can kill without warning. Exhaust system must be tightly sealed.

Disconnecting or loosening any hydraulic tubeline, hose, fitting, component or a part failure can cause lift arms to drop. Do not go under lift arms when raised unless supported by an approved lift arm support device. Replace it if damaged.

Never work on loader with lift arms up unless lift arms are held by an approved lift arm support device. Replace if damaged. Never modify equipment or add attachments not approved by Bobcat Company.

WRONG

WRONG

WRONG

B-6590

B-6580 B-16102

B-6589 B-16102

Stop, cool and clean engine of flammable materials before checking fluids. Never service or adjust loader with the engine running unless instructed to do so in the manual. Avoid contact with leaking hydraulic fluid or diesel fuel under pressure. It can penetrate the skin or eyes. Never fill fuel tank with engine running, while smoking or when near open flame.

Keep body, jewelry and clothing away from moving parts, electrical contact, hot parts and exhaust. Wear eye protection to guard from battery acid, compressed springs, fluids under pressure and flying debris when engines are running or tools are used. Use eye protection approved for type of welding. Keep rear door closed except for service. Close and latch door before operating the loader.

Lead-acid batteries produce flammable and explosive gases. Keep arcs, sparks, flames and lighted tobacco away from batteries. Batteries contain acid which burns eyes or skin on contact. Wear protective clothing. If acid contacts body, flush well with water. For eye contact flush well and get immediate medical attention.

Maintenance procedures which are given in the Operation & Maintenance Manual can be performed by the owner/ operator without any specific technical training. Maintenance procedures which are not in the Operation & Maintenance Manual must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL. Always use genuine Bobcat replacement parts. The Service Safety Training Course is available from your Bobcat dealer. MSW01-0805


ALPHABETICAL INDEX AIR CLEANER ........................................................ 70-01 AIR CLEANER SERVICE ....................................... 10-01 ALTERNATOR ........................................................ 60-01 AUXILIARY CONTROL LOCKBOLT....................... 10-01 BATTERY................................................................ 60-01 BICS™ SYSTEM (WITH PRESS TO OPERATE BUTTON) ............................................................ 60-01 BLOWER FAN HOUSING....................................... 70-01 BOBCAT INTERLOCK CONTROL SYSTEM (BICS™) ....................... 60-01 BOB-TACH ............................................... 10-01, 50-01 CHAINCASE ........................................................... 40-01 CONTROL PANEL .................................................. 30-01 CONTROL PEDALS ............................................... 50-01 CONVERSIONS ............................................SPEC-01 CYLINDER (LIFT) ................................................... 20-01 CYLINDER (TILT) ............................................... 20-01 DRIVE COMPONENTS .......................................... 40-01 ELECTRICAL SYSTEM INFORMATION ................ 60-01 ENGINE ................................................................. 70-01 ENGINE COMPONENTS AND TESTING .............. 70-01 ENGINE COOLING SYSTEM ................................. 10-01 ENGINE LUBRICATION SYSTEM.......................... 10-01 ENGINE SPECIFICATIONS ...........................SPEC-01 ENGINE SPEED CONTROL .................................. 70-01 FINAL DRIVE TRANSMISSION (CHAINCASE) .. 10-01 FLYWHEEL .......................................................... 70-01 FUEL SYSTEM ....................................................... 10-01 FUEL TANK............................................................. 50-01

HYDRAULIC CONTROL VALVE............................. 20-01 HYDRAULIC FILTER HOUSING ............................20-01 HYDRAULIC FLUID RESERVOIR..........................20-01 HYDRAULIC FLUID SPECIFICATIONS ............SPEC-01 HYDRAULIC PUMP ................................................20-01 HYDRAULIC/HYDROSTATIC FLUID SPECIFICATIONS .......................... SPEC-01 HYDRAULIC/HYDROSTATIC SYSTEM ................. 10-01 HYDRAULIC SYSTEM INFORMATION.................. 20-01 HYDROSTATIC MOTOR .....................................30-01 HYDROSTATIC PUMP ........................................30-01 HYDROSTATIC SYSTEM INFORMATION ......... 30-01 INSTRUMENT PANEL ............................................ 60-01

LIFT ARM ................................................................50-01 LIFT ARM BY-PASS CONTROL VALVE..................20-01 LIFT ARM SUPPORT DEVICE ........................... 10-01 LIFTING AND BLOCKING THE LOADER...............10-01 LIGHTS ................................................................60-01 LOADER SPECIFICATIONS ............................. SPEC-01 LUBRICATION OF THE BOBCAT LOADER ...........10-01

MAIN RELIEF VALVE ..............................................20-01 MUFFLER................................................................70-01 OIL COOLER...........................................................30-01 OPERATOR CAB .........................................10-01, 50-01 OPERATOR SEAT...................................................50-01 PARKING BRAKE...................................................40-01 PIVOT PINS ...........................................................10-01 PORT BLOCK.........................................................30-01 RADIATOR ..............................................................70-01 REAR DOOR .......................................................50-01 REAR GRILL .......................................................50-01 RECONDITIONING THE ENGINE ..........................70-01 REMOTE START .................................................10-01 RUBBER COUPLER LUBRICATION ..................... 10-01 RUBBER DRIVE COUPLER .................................. 70-01 SEAT BAR ...............................................................50-01 SEAT BAR RESTRAINT SYSTEM ......................... 01-01 SERVICE SCHEDULE ............................................10-01 SPARK ARRESTOR MUFFLER..............................10-01 STARTER ................................................................60-01 STEERING ............................................................. 30-01 TIRE MAINTENANCE .............................................10-01 TORQUE SPECIFICATIONS FOR BOLTS ... SPEC-01 TOWING THE LOADER ..........................................10-01 TRANSPORTING THE BOBCAT LOADER.............10-01 TROUBLESHOOTING ............................................70-01 WATER FLANGE.....................................................70-01


SAFETY & MAINTENANCE

CONTENTS FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V

HYDRAULIC SYSTEM

SERIAL NUMBER LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IX DELIVERY REPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X

HYDROSTATIC SYSTEM

BOBCAT LOADER IDENTIFICATION. . . . . . . . . . . . . . . . . . . . . . . . XI SAFETY AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . 10-01 HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-01

DRIVE SYSTEM

HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-01 MAIN FRAME DRIVE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-01 MAIN FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-01 ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-01

ELECTRICAL SYSTEM

ENGINE SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-01 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-01

ENGINE SERVICE

SPECIFICATIONS

SPECIFICATIONS

SPECIFICATIONS

I

553 Bobcat Loader Service Manual


FOREWORD This manual is for the Bobcat loader mechanic. It provides necessary servicing and adjustment procedures for the Bobcat loader and its component parts and systems. Refer to the Operation & Maintenance Manual for operating instructions, Starting procedure, daily checks, etc. A general inspection of the following items must be made after the loader has had service or repair: 1. Check lift arm support device, replace if damaged. (Stored Position)

9. The parking brake function correctly.

2. Check that ROPS mounting hardware is tightened and is Bobcat approved.

10. Enclosure door latches must open and close freely.

3. The seat belt must be correctly installed, functional and in good condition.

11. Bob-Tach wedges and linkages must function correctly and be in good condition.

4. The seat bar must be correctly adjusted, clean and lubricated.

12. Safety treads must be in good condition.

5. Check lift arm support device; replace if damaged.

13. Check for correct function of indicator lamps (Optional on some models).

6. Machine signs must be legible and in the correct location.

14. Check hydraulic fluid level, engine oil level and fuel supply.

7. Steering levers and foot pedals must return to neutral.

15. Inspect for fuel, hydraulic fluid leaks.

8. Check for correct function of the work lights

16. Lubricate the loader.

II

must

oil

or

553 Bobcat Loader Service Manual


17. Check the condition of the battery and cables.

22. Operate the loader and check all functions.

18. Inspect the air cleaner for damage or leaks. Check the condition of the element.

23. Check for any field modification not completed.

19. Check the electrical charging system.

24. Check for correct function of the Bobcat Interlock Control System (BICS™) before the machine is returned to the customer.

20. Check tires for wear and pressure.

Recommend to the owner that all necessary corrections be made before the machine is returned to service.

21. Inspect for loose or broken parts or connections.

CALIFORNIA PROPOSITION 65 WARNING Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm.

III

553 Bobcat Loader Service Manual


SAFETY INSTRUCTIONS

The following publications provide information on the safe use and maintenance of the Bobcat machine and attachments:

Safety Alert Symbol This symbol with a warning statement means: “Warning, be alert! Your safety is involved!” Carefully read the message that follows.

The Delivery Report is used to assure that complete instructions have been given to the new owner and that the machine is in safe operating condition.

The Operation & Maintenance Manual delivered with the machine or attachment contains operating information as well as routine maintenance and service procedures. It is a part of the machine and can be stored in a container provided on the machine. Replacement Operation & Maintenance Manuals can be ordered from your Bobcat dealer.

Machine signs (decals) instruct on the safe operation and care of your Bobcat machine or attachment. The signs and their locations are shown in the Operation & Maintenance Manual. Replacement signs are available from your Bobcat dealer.

An Operator’s Handbook fastened to the operator cab. It’s brief instructions are convenient to the operator. The handbook is available from your dealer in an English edition or one of many other languages. See your Bobcat dealer for more information on translated versions.

The AEM Safety Manual delivered with the machine gives general safety information.

The Service Manual and Parts Manual are available from your dealer for use by mechanics to do shoptype service and repair work.

The Skid-Steer Loader Operator Training Course is available through your local dealer or at www.training.bobcat.com or www.bobcat.com. This course is intended to provide rules and practices of correct operation of the Skid-Steer Loader. The course is available in English and Spanish versions.

Service Safety Training Courses are available from your Bobcat dealer or at www.training.bobcat.com or www.bobcat.com. They provide information for safe and correct service procedures.

The Skid-Steer Loader Safety Video is available from your Bobcat dealer or at www.training.bobcat.com or www.bobcat.com.

WARNING Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Operator’s Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death. W-2003-0903

WARNING Warnings on the machine and in the manuals are for your safety. Failure to obey warnings can cause injury or death. W-2044-1285

IMPORTANT This notice identifies procedures which must be followed to avoid damage to the machine. I-2019-0284

SI SSL-0206 SM

V

553 Bobcat Loader Service Manual


SAFETY INSTRUCTIONS (CONT’D)

Use the procedure in the Operation & Maintenance Manual for connecting the battery and for jump starting.

Use the procedure in the Operation & Maintenance Manual for cleaning the spark arrestor muffler (if equipped).

Fire Prevention The machine and attachments have components that are at high temperature under normal operating conditions. The primary source of high temperatures is the engine and exhaust system. The electrical system, if damaged or incorrectly maintained, can be a source of arcs or sparks.

Figure 1

Flammable debris (leaves, straw, etc.) must be removed regularly. If flammable debris is allowed to accumulate, it will increase fire hazard. Clean often to avoid this accumulation. Flammable debris in the engine compartment is a potential hazard. The spark arrestor muffler is designed to control the emission of hot particles from the engine and exhaust system, but the muffler and the exhaust gases are still hot. •

Do not use the machine where exhaust, arcs, sparks or hot components can contact flammable material, explosive dust or gases.

The operator cab, engine compartment, and engine cooling system must be inspected every day and cleaned if necessary to prevent fire hazard and overheating.

Check all electrical wiring and connections for damage. Keep the battery terminals clean and tight. Repair or replace any damaged part.

Check fuel and hydraulic tubes, hoses and fittings for damage and leakage. Never use open flame or bare skin to check for leaks. Tighten or replace any parts that show leakage. Always clean fluid spills. Do not use gasoline or diesel fuel for cleaning parts. Use commercial nonflammable solvents.

Do not use ether or starting fluids on any engine which has glow plugs. These starting aids can cause explosion and injure you or bystanders.

Always clean the machine, disconnect the battery, and disconnect the wiring from the controllers before welding. Cover rubber hoses, battery and all other flammable parts. Keep a fire extinguisher near the machine when welding. Have good ventilation when grinding or welding painted parts. Wear a dust mask when grinding painted parts. Toxic dust or gas can be produced.

Stop the engine and let it cool before adding fuel. NO SMOKING!

Know where fire extinguishers and first aid kits are located and how to use them. Fire extinguishers are available from your Bobcat dealer [Figure 1].

SI SSL-0206 SM

VII

553 Bobcat Loader Service Manual


SERIAL NUMBER LOCATION

Engine Serial Number

Always use the serial number of the loader when requesting service information or when ordering parts. Early or later models (identification made by serial number) may use different parts, or it may be necessary to use a different procedure in doing a specific service operation.

Figure 3

1

Loader Serial Number Figure 2

N-09931

The engine serial number (Item 1) [Figure 3] is in the location shown.

P10725

The loader serial number plate is located on the outside of the loader frame [Figure 2]. Explanation of loader Serial Number: XXXX Model/ Engine Version

XXXXX Production Sequence (Series)

1. The four digit Model/Engine Combination Module number identifies the model number and engine combination. 2. The five digit Production Sequence Number identifies the order which the loader is produced.

IX

553 Bobcat Loader Service Manual


DELIVERY REPORT Figure 4

B-16315

The Delivery Report must be filled out by the dealer and signed by the owner or operator when the Bobcat loader is delivered. An explanation of the form must be given to the owner. Make sure it is filled out completely [Figure 4].

X

553 Bobcat Loader Service Manual


BOBCAT LOADER IDENTIFICATION ‹ FRONT LIGHTS OPERATOR SEAT WITH SEAT BELT SEAT BAR GRAB HANDLES STEERING LEVER STABILIZER ROD TILT CYLINDER † BUCKET

‹ QUICK COUPLERS

BUCKET STEPS SAFETY TREAD

‹REAR WINDOW

zOPERATOR CAB (ROPS & FOPS)

UPRIGHTS REAR GRILL LIFT ARM ‹TAIL LIGHT

LIFT CYLINDER

‹REAR LIGHT

REAR DOOR

* TIRES

B-15064 B-15065

‹ OPTIONAL OR FIELD ACCESSORY (Not Standard Equipment) * TIRES - The Bobcat loader is factory equipped with heavy duty flotation tires. See Specifications Section and your Bobcat dealer for available tires. † BUCKET - Several different buckets and other attachments are available for the Bobcat loader. z ROPS, FOPS - Roll Over Protective Structure, per SAE J1040 and ISO 3471, and Falling Object Protective Structure per SAEJ1043 and ISO 3449, Level I. Level II is available. The Bobcat loader is base-equipped with a standard operator cab as shown. Extra insulated cab is available as an option (Reduced noise level).

XI

553 Bobcat Loader Service Manual


SAFETY & MAINTENANCE

SAFETY AND MAINTENANCE AIR CLEANER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1 Replacing Filter Element . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1 AUXILIARY CONTROL LOCKBOLT . . . . . . . . . . . . . . . . . . . 10-140-1 Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1

SAFETY & MAINTENANCE

BOB-TACH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-150-1 Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . 10-150-1 ENGINE COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . Checking The Coolant Level . . . . . . . . . . . . . . . . . . . . . . . Cleaning The Cooling System . . . . . . . . . . . . . . . . . . . . . . Replacing The Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . ENGINE LUBRICATION SYSTEM . . . . . . . . . . . . . . . . . . . . Checking Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing Oil And Filter . . . . . . . . . . . . . . . . . . . . . . . . . .

10-90-1 10-90-2 10-90-1 10-90-2

DRIVE SYSTEM

10-110-1 10-110-1 10-110-1 10-110-1

FINAL DRIVE TRANSMISSION (CHAINCASE) . . . . . . . . . . 10-130-1 Checking And Adding Oil . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1

ELECTRICAL SYSTEM & ANALYSIS

FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filling The Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing Air From The Fuel System . . . . . . . . . . . . . . .

10-100-1 10-100-1 10-100-2 10-100-1 10-100-3

ENGINE SERVICE

HYDRAULIC/HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . Checking And Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing Hydraulic Fluid . . . . . . . . . . . . . . . . . . . . . . . . Replacing The Hydraulic/Hydrostatic Filter . . . . . . . . . . .

10-120-1 10-120-1 10-120-1 10-120-2 10-120-2

SPECIFICATIONS

LIFT ARM SUPPORT DEVICE . . . . . . . . . . . . . . . . . . . . . . . . 10-20-1 Installing Lift Arm Support Device . . . . . . . . . . . . . . . . . . . 10-20-1 Removing Lift Arm Support Device . . . . . . . . . . . . . . . . . . 10-20-2 LIFTING AND BLOCKING THE LOADER . . . . . . . . . . . . . . . 10-10-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10-1 LUBRICATION OF THE BOBCAT LOADER. . . . . . . . . . . . . 10-160-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-160-1 Continued On Next Page

10-01

553 Bobcat Loader Service Manual


SAFETY AND MAINTENANCE (CONT’D) OPERATOR CAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lowering The Operator Cab . . . . . . . . . . . . . . . . . . . . . . . Raising The Operator Cab . . . . . . . . . . . . . . . . . . . . . . . . .

10-30-1 10-30-1 10-30-2 10-30-2 10-30-1

PIVOT PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-190-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-190-1 REMOTE START. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-60-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-60-1 RUBBER COUPLER LUBRICATION . . . . . . . . . . . . . . . . . . 10-210-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-210-1 SEAT BAR RESTRAINT SYSTEM . . . . . . . . . . . . . . . . . . . . Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seat Bar Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seat Bar Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .

10-200-1 10-200-1 10-200-1 10-200-1

SERVICE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1 SPARK ARRESTOR MUFFLER . . . . . . . . . . . . . . . . . . . . . . 10-180-1 Cleaning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-180-1 TIRE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10-170-1 10-170-1 10-170-1 10-170-1

TOWING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1 TRANSPORTING THE BOBCAT LOADER . . . . . . . . . . . . . . 10-40-1 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1 Stopping The Bobcat Loader . . . . . . . . . . . . . . . . . . . . . . . 10-40-1

10-02

553 Bobcat Loader Service Manual


LIFTING AND BLOCKING THE LOADER

Figure 10-10-2

Figure 10-10-1

P10938 B-7023A

Lift the rear of the loader and install jackstands [Figure 10-10-2]. Figure 10-10-3

WARNING Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death. W-2003-0199

Procedure

P10917

Always park the loader on a level surface. Lift the front of the loader and put jackstands under the loader frame [Figure 10-10-3].

WARNING

NOTE: Make sure the jackstands do not touch the tires.

Put jackstands under the front axles and rear corners of the frame before running the engine for service. Failure to use jackstands can allow the machine to fall or move and cause injury or death. W-2017-0286

10-10-1

553 Bobcat Loader Service Manual


LIFT ARM SUPPORT DEVICE

Put jackstands under the rear corners of the loader frame.

Installing Lift Arm Support Device Remove any attachment before raising the lift arms.

WARNING Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device. Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death.

Disconnect the spring from the approved lift arm support device retaining pin (Item 1) [Figure 10-20-1]. Hold onto the lift arm support device (Item 2) [Figure 10-20-1] and remove the retaining pin. Figure 10-20-2

W-2059-0598

1

WARNING Service lift arm support device if damaged or if parts are missing. Using a damaged lift arm support or with missing parts can cause lift arms to drop causing injury or death. W-2271-1197

P10703

Lower the lift arm support device on top of the lift cylinder. Hook the free end of the spring (Item 1) [Figure 10-20-2] to the lift arm support device so there will be no interference with the support device engagement. With the operator in the seat, seat belt fastened and seat bar lowered, start the engine. Loaders without seat sensors Press the green PRESS TO OPERATE Button. Figure 10-20-1

2 1

P10706

Maintenance and service work can be done with the lift arms lowered. If the lift arms are raised for service, use the following procedure:

10-20-1

553 Bobcat Loader Service Manual


LIFT ARM SUPPORT DEVICE (CONT’D)

Removing Lift Arm Support Device

Installing Lift Arm Support Device (Cont’d)

Figure 10-20-5

Figure 10-20-3

1 P-10707

1 P10702 P10708

Remove the pin from the lift arm support device.

Raise the lift arms, until the lift arm support device (Item 1) [Figure 10-20-3] drops onto the lift cylinder rod.

Connect the spring (Item 1) [Figure 10-20-5] from the lift arm support device to the bracket below the lift arms.

Lower the lift arms slowly until the support device is held between the lift arm and the lift cylinder. Stop the engine. Raise the seat bar and move foot pedals (or hand controls) until both lock.

With the operator in the seat, seat belt fastened and seat bar lowered, start the engine. Loaders without seat sensors press the green PRESS TO OPERATE Button.

Figure 10-20-4 Raise the lift arms a small amount and the spring will lift the support device off the lift cylinder rod. Lower the lift arms and stop the engine. Raise the seat bar and move pedals until both lock. Disconnect the spring from the bracket.

1

P10701

Install pin (Item 1) [Figure 10-20-4] into the rear of the lift arm support device below the cylinder rod.

10-20-2

553 Bobcat Loader Service Manual


LIFT ARM SUPPORT DEVICE (CONT’D) Removing Lift Arm Support Device (Cont’d) Figure 10-20-6

1

P10706

Raise the support device into storage position and insert pin (Item 1) [Figure 10-20-6] through lift arm support device and bracket. Connect spring to pin.

10-20-3

553 Bobcat Loader Service Manual


Put jackstands under the rear corners of loader (Inset) [Figure 10-30-2].

OPERATOR CAB Description The Bobcat loader has an operator cab (ROPS and FOPS) as standard equipment to protect the operator from rollover and falling objects. Check with your dealer if the operator cab has been damaged. The seat belt must be worn for roll over protection. ROPS/FOPS - Roll Over Protective Structure per SAE J1040 and ISO 3471, and Falling Object Protective Structure per SAE J1043 and ISO 3449, Level I. Level II is available. Level I - Protection from falling bricks, small concrete blocks, and hand tools encountered in operations such as highway maintenance, landscaping, and other construction site services.

Loosen the nut (both sides) at the corner of the operator cab [Figure 10-30-1]. Remove the nut and plate (both sides) [Figure 10-30-1].

WARNING Before the cab or the lift arms are raised for service, jackstands must be put under the rear corners of the frame. Failure to use jackstands can allow the machine to tip backward causing injury or death. W-2014-0895

Level II - Protection from falling trees, rocks; for machines involved in site clearing, overhead demolition or forestry.

WARNING Both sets of fasteners at the front of the operator cab (ROPS) must be assembled as shown in this manual. Failure to secure ROPS correctly can cause injury or death.

WARNING Never modify operator cab by welding, grinding, drilling holes or adding attachments unless instructed to do so by Bobcat. Changes to the cab can cause loss of operator protection from rollover and falling objects, and result in injury or death.

W-2005-1189

Figure 10-30-2

W-2069-1299

Raising The Operator Cab Figure 10-30-1

P-9773

P10719

Lift on the grab handle and bottom of the operator cab slowly until the cab latching mechanism engages and the cab is all the way up [Figure 10-30-2]. P10724

P10723

Stop the loader on a level surface. Lower the lift arms. Stop the engine. If the lift arms must be up while raising the operator cab, install the lift arm support device. (See Installing Lift Arm Support Device on Page 10-20-1.) 10-30-1

553 Bobcat Loader Service Manual


OPERATOR CAB (CONT'D)

Emergency Exit

Lowering The Operator Cab

Figure 10-30-4

Figure 10-30-3

P-10715

P0660

The front opening on the operator cab and rear window provide exits.

P10713

Pull down on the bottom of the operator cab until it stops at the latching mechanism. Release the latching mechanism [Figure 10-30-3] and pull the cab all the way down.

Rear Window (If Equipped)

Install the plate and nut (both sides) [Figure 10-30-1].

Push the rear window out of the rear of the operator cab.

Tighten the nuts [Figure 10-30-1] to 40-50 ft.-lbs. (54-68 Nm) torque.

Figure 10-30-5

Pull on the tag on the top of the rear window to remove the rubber cord [Figure 10-30-4].

P10722

Exit through the rear of the operator cab [Figure 10-305].

10-30-2

553 Bobcat Loader Service Manual


OPERATOR CAB (CONT'D) Emergency Exit (Cont’d) Figure 10-30-6

P9216

Front Door (If Equipped) NOTE: When an Operator Cab Enclosure Kit is installed, the window of the front door can be used as an emergency exit. [Figure 10-30-6]. Pull the plastic loop at the top of the window in the front door to remove the rubber cord [Figure 10-30-6]. Figure 10-30-7

P9217

Push the window out with your foot [Figure 10-30-7] at any corner of the window. Exit through the front door.

10-30-3

553 Bobcat Loader Service Manual


Figure 10-40-2

TRANSPORTING THE BOBCAT LOADER Procedure

WARNING Adequately designed ramps of sufficient strength are needed to support the weight of the machine when loading onto a transport vehicle. Wood ramps can break and cause personal injury.

P10731

W-2058-0494

Figure 10-40-1

P10730

SUPPORT P10732 P-10726A

A loader with an empty bucket or no attachment must be loaded backward onto the transport vehicle [Figure 1040-1]. The rear of the trailer must be blocked or supported [Figure 10-40-1] when loading or unloading the loader to prevent the front end of the trailer from raising up.

P10728

Use the following procedure to fasten the Bobcat loader to the transport vehicle to prevent the loader from moving during sudden stops or when going up or down slopes [Figure 10-40-2]. •

Lower the bucket or attachment to the floor.

Stop the engine.

Engage the parking brake.

Install chains at the front and rear loader tie down positions (Inset) [Figure 10-40-2].

Stopping The Bobcat Loader

10-40-1

553 Bobcat Loader Service Manual


When the steering levers are moved to the neytral position, the hydrostatic transmission will act as a service brake and stop the loader.

10-40-2

553 Bobcat Loader Service Manual


Lower the operator cab. (See Lowering The Operator Cab on Page 10-30-2.)

TOWING THE LOADER Procedure

The towing chain (or cable) must be rated at 1 and 1/2 times the weight of the loader. (See Performance on Page SPEC-10-2.)

IMPORTANT Never attempt to start the engine by pushing or pulling. Hydrostatic pumps and motors will be damaged.

•

Turn the key switch to ON and press the traction lock override button.

•

Tow the Bobcat at 2 MPH (3,2 km/hr) or less for not more than 25 feet (7,6 meters).

I-2001-0285

If the electrical system is not functioning, contact your Bobcat loader dealer. (Part of the brake system must be disassembled to move the loader.)

IMPORTANT Do not push or pull the machine at more than 2 MPH (3,2 km/h) or for a distance of more than 25 feet (7,6 meters) with the towing tool in place. I-2017-0389

Figure 10-50-1

B-6924 E-1457A

To prevent damage to the loaders hydrostatic system, the loader must be towed only a short distance at slow speed. (Example: Moving the loader onto a transport vehicle.) Relief valve release tool set MEL1220 is available from your dealer. Tool must be installed before towing. Raise the operator cab. (See Raising The Operator Cab on Page 10-30-1.) Clean the area around the hydrostatic pumps. Remove the high pressure relief valve from one side of each hydrostatic pump [Figure 10-50-1] and install the relief valve tubes. Install the plugs and tighten.

10-50-1

553 Bobcat Loader Service Manual


The Remote Start Switch is required when the service technician is adjusting the steering linkage, checking the hydraulic/hydrostatic system.

REMOTE START Procedure

Lift and block the loader. (See LIFTING AND BLOCKING THE LOADER on Page 10-10-1.)

WARNING Never work on a machine with the lift arms up unless the lift arms are secured by an approved lift arm support device. Failure to use an approved lift arm support device can allow the lift arms or attachment to fall and cause injury or death. W-2059-0598

WARNING Put jackstands under the front axles and rear corners of the frame before running the engine for service. Failure to use jackstands can allow the machine to fall or move and cause injury or death.

Raise the lift arms and install an approved lift arm support device. (See Installing Lift Arm Support Device on Page 10-20-1.) Raise the operator cab. (See Raising The Operator Cab on Page 10-30-1.) NOTE: On current model loaders, the connector on the BICS harness is round (7-pin) connector, not a rectangular (8-pin) connector. Use the adapter harness (Item 1) [Figure 10-60-1] to connect the remote start switch to the loader harness. Figure 10-60-2

W-2017-0286

1

1

Figure 10-60-1

P10965

Disconnect the operator cab wire harness (Item 1) [Figure 10-60-2] from the engine wire harness.

1 P7101

The tool listed below will be needed to do the following procedure: MEL1492B - Remote Start Switch

10-60-1

553 Bobcat Loader Service Manual


Figure 10-60-4

REMOTE START (CONT'D) Procedure (Cont'd) Figure 10-60-3

1

1

P4713

Put the traction lock override switch (Item 1) [Figure 1060-4] in the ON position so the traction function is locked. The wheels are not able to turn.

1

Turn the key to the right and start the engine. Figure 10-60-5

1

P10966

2 Connect the remote start switch to the engine harness connectors (Item 1) [Figure 10-60-3].

P4714

Move the traction lock override switch (Item 1) [Figure 10-60-5] to the OFF position so the traction function is unlocked. The wheels are now able to turn. The auxiliary mode switch (Item 2) [Figure 10-60-5] is used to turn the front auxiliary quick couplers ON and OFF during relief pressure and flow tests.

10-60-2

553 Bobcat Loader Service Manual


SERVICE SCHEDULE Chart Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The service schedule is a guide for correct maintenance of the Bobcat loader.

WARNING

Instructions are necessary before operating or servicing machine. Read and understand the Operation & Maintenance Manual, Handbook and signs (decals) on machine. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service. Untrained operators and failure to follow instructions can cause injury or death.

W-2003-0199

SERVICE SCHEDULE ITEM Engine Oil Engine Air Filter and Air System Engine Cooling System

SERVICE REQUIRED

Check for damaged tires and correct air pressure.

Seat Belt and Seat Bar and Control Interlocks Safety Signs and Safety Treads

Check the condition of seat belt. Check the sear bar and pedal interlocks for correct operation. Clean dirt and debris from moving parts. Check for damaged signs (decals) and safety treads. Replace any signs or safety treads that are damaged or worn. Check for correct operation of all indicators and lights. Check the fastening bolts, washers and nuts. Check the condition of the cab. Lubricate with multi-purpose lithium based grease.

Parking Brake

Remove the trapped water. Check BICS™ System Controller functions. Clean dirt, debris or objects from under or behind seat as required. Check fluid level and add as needed. Check for damage and leaks. Repair or replace as needed. Check for correct operation. Repair or adjust as needed. ❏Check for loose wheel nuts and tighten to 105-115 ft.-lbs. (142-156 Nm) torque Check operation.

Alrernation Belt Battery Engine/Hydro. Drive Belt Alternator Belt Final Drive Trans. (Chaincase)

Check tension & adjust as needed. Check cables, connections and electrolyte level. Add distilled water as needed. Check for wear or damage. Check idler arm stop. Check tension and adjust as needed. Check fulid level and add as needed.

Spark Arrestor Muffler Battery Engine Oil and Filter Fuel Filter U Joint

Clean the sprk chamber. Check cables, connections & electrolyte level. Add distilled water as needed. Replace oil and filter. Use CD or better grade oil and Bobcat filter. Replace filter element. Grease two fittings. Add oil to steering shaft. Grease fitting.

Hyd./Hydros Filter Hyd Reservoir Breather Cap

● Replace the filter element. Replace the reservoir breather cap.

Hydraulic/Hydrostatic Reservoir Chaincase

Replace the fluid. Replace the fluid.

Steering Lever Pivots

8-10

50

100

■ 200 250 500 1000

Check the oil level and add as needed. Check display panel. Service only when required. Check for leaks and damaged components. Clean debris from oil cooler, radiator & grill.

Tires

Indicators and Lights (Opt.) Operator Cab Lift Arms, Bob-Tach Pivot Pins and Wedges Engine Fuel Filter Bobcat Interlock Control Systems (BICS™) Hydraulic Fluid, Hoses and Tubelines Control Pedals & Steering Wheel Nuts

HOURS

Bobcat Interlock Control System Check the lift arm by-pass control. (BICS™) ❏ Check wheel nut torque every 8 hours for the first 24 hours. ● Also replace hydraulic/hydrostatic filter element when the transmission warning light stays on for five minutes after the fluid is at operating temperature. ■ Or every 12 months.

10-70-1

553 Bobcat Loader Service Manual


Figure 10-80-3

AIR CLEANER SERVICE Replacing Filter Element Figure 10-80-1

1

P10734

Outer Element: P10747

Pull the outer filter element from the air cleaner housing [Figure 10-80-3]. (See SERVICE SCHEDULE on Page 10-70-1.) for the interval to service the air cleaner system. Check the air intake hose for damage. Check the air cleaner housing for damage. Check to make sure all connections are tight.

NOTE: Make sure all sealing surfaces are free of dirt and debris. Install a new outer element. Install the dust cover and fasten the clamps.

Replace the large (outer) filter element only when the red ring shows in the window (Item 1) [Figure 10-80-1] of the condition indicator. NOTE: Push the button on the condition indicator (See Inset) and start the engine. If the red ring does not show, do not replace the filter element [Figure 10-80-1]. Figure 10-80-2

1

2

P10733

Disengage the clamps (Item 1) [Figure 10-80-2] and remove the dust cover (Item 2) [Figure 10-80-2].

10-80-1

553 Bobcat Loader Service Manual


AIR CLEANER SERVICE (CONT’D) Replacing Filter Element (Cont’d) Figure 10-80-4

P10729

Inner Element: Only replace the inner filter element under the following conditions [Figure 10-80-4]: •

Replace the inner filter element every third time the outer filter is replaced.

Replace the inner filter element when the red ring still shows in the condition indicator window after the outer filter is replaced.

Pull the inner filter element from the air cleaner housing. NOTE: Make sure all sealing surfaces are free of dirt and debris. Install the new inner element. Record the operating hours of the loader on the decal inside the rear door.

10-80-2

553 Bobcat Loader Service Manual


Figure 10-90-2

ENGINE COOLING SYSTEM Cleaning The Cooling System

WARNING Wear safety glasses to prevent eye injury when any of the following conditions exist: • When fluids are under pressure. • Flying debris or loose material is present. • Engine is running. • Tools are being used. W-2019-1285 P10743

Figure 10-90-1 Use air pressure or water pressure to remove the debris in the area of the radiator and oil cooler [Figure 10-90-2]. Install the rear grill and close the rear door.

1

P10749

Check the cooling system every day to prevent overheating, loss of performance or engine damage. Open the rear door. Remove the access panel from the blower housing (Item 1) [Figure 10-90-1]. Remove the rear grill. (See Removal And Installation on Page 50-60-1.)

10-90-1

553 Bobcat Loader Service Manual


Replacing The Coolant

ENGINE COOLING SYSTEM (CONT’D) Checking The Coolant Level

IMPORTANT

Figure 10-90-3

AVOID ENGINE DAMAGE Always use the correct ratio of water to antifreeze. Too much antifreeze reduces cooling system efficiency and may cause serious premature engine damage. 1

Too little antifreeze reduces the additives which protect the internal engine components; reduces the boiling point and freeze protection of the system. Always add a premixed solution. Adding full strength concentrated coolant can cause serious premature engine damage.

P10760

I-2124-0497

Open the rear door. The coolant recovery tank (Item 1) [Figure 10-90-3] must be at the FULL COLD mark when engine is cool.

Figure 10-90-4

Propylene Glycol NOTE: The loader is factory filled with propylene glycol coolant. DO NOT mix propylene glycol with ethylene glycol.

1

Add premixed coolant; 47% water and 53% propylene glycol to the recovery tank if the coolant level is low. One gallon and one pint of propylene glycol mixed with one gallon of water is the correct mixture of coolant to provide a -34°F (-37°C) freeze protection. P10744

Use a refractometer to check the condition of propylene glycol in your cooling system. Close the rear door before operating the loader.

Open the rear door. Remove the rear grill. (See Removal And Installation on Page 50-60-1.) Remove the radiator cap (Item 1) [Figure 10-90-4].

10-90-2

553 Bobcat Loader Service Manual


Figure 10-90-6

ENGINE COOLING SYSTEM (CONT’D) Replacing The Coolant (Cont’d) Figure 10-90-5

1

P10760

1 Fill the coolant recovery tank 1/3 full with premixed coolant (Item 1) [Figure 10-90-6].

P10687

Connect a hose to the coolant drain valve (Item 1) [Figure 10-90-5] or use a funnel to keep coolant from getting into the engine compartment. Open the valve and drain all the coolant into a container. Close the valve.

Check the radiator cap for correct pressure rating or overheating can result. Check for leaks in the cooling system. Check for worn or damaged hoses, clamps or radiator. Check for loose or worn water pump belt. Replace damaged parts immediately to prevent leaks and overheating.

Fill the radiator with premixed coolant and install the radiator cap. (See Checking The Coolant Level on Page 10-90-2.) for premix recommendations.)

Install the radiator cap and the rear grill and close the rear door.

10-90-3

553 Bobcat Loader Service Manual


FUEL SYSTEM

Figure 10-100-1

Fuel Specifications Use only clean, high quality diesel fuel, Grade No. 2 or Grade No. 1. The following is one suggested blending guideline which should prevent fuel gelling during cold temperatures: TEMP. F° (C°)

NO. 2

NO. 1

+15° (-9°)

100%

0%

Down to -20° (-29°)

50%

50%

Below -20° (-29°)

0%

100%

1

P10710

Contact your fuel supplier for local recommendations.

Remove the fuel fill cap (Item 1) [Figure 10-100-1]

Filling The Fuel Tank

Use a clean, approved safety container to add fuel of the correct specifications. Add fuel only in an area that has free movement of air and no open flames or sparks. NO SMOKING!

WARNING

Install and tighten the fuel fill cap (Item 1) [Figure 10100-1].

Stop and cool the engine before adding fuel. NO SMOKING! Failure to obey warnings can cause an explosion or fire. W-2063-0887

WARNING Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death. W-2103-1285

10-100-1

553 Bobcat Loader Service Manual


FUEL SYSTEM (CONT’D)

Replacing Filter:

Fuel Filter

Clean the area around the fuel filter.

Figure 10-100-2

Close the shut-off valve (Item 1) [Figure 10-100-2]. Remove the fuel filter element (Item 2) [Figure 10-100-3] Install the new filter element. Tighten the fuel filter. Open the shut-off valve [Figure 10-100-2]

1

P10714

Figure 10-100-3

2

1 P10678

(See SERVICE SCHEDULE on Page 10-70-1.) for the service interval for removing water from, or replacing the fuel filter. Removing Water Shut-off the fuel supply (Item 1) [Figure 10-100-2] (turn clockwise). Loosen the drain at the bottom of the filter element (Item 1) [Figure 10-100-3] to drain water from the filter. Open the shut-off valve [Figure 10-100-2].

10-100-2

553 Bobcat Loader Service Manual


FUEL SYSTEM (CONT’D)

WARNING

Removing Air From The Fuel System Figure 10-100-4

Always clean up spilled fuel or oil. Keep heat, flames, sparks or lighted tobacco away from fuel and oil. Failure to use care around combustibles can cause explosion or fire which can result in injury or death.

3

W-2103-1285

After replacing the filter element or when the fuel tank has run out of fuel, the air must be removed from the fuel system before starting the engine. Open the vent plug (Item 1) [Figure 10-100-4] on top of the fuel filter head. P-10679

Operate the hand pump (Item 2) [Figure 10-100-4] until fuel flows from the vent with no air bubbles. Tighten the vent plug. Operate the hand pump [Figure 10-100-4] until it feels solid. Move the engine speed control to minimum RPM. Open the valve (Item 3) [Figure 10-100-4] and squeeze the hand pump several times. Start the engine. When the engine runs smoothly, close the valve (Item 3) [Figure 10-100-4]. Close the rear door.

P-10675

1

2

P-10678

10-100-3

553 Bobcat Loader Service Manual


ENGINE LUBRICATION SYSTEM

Replacing Oil And Filter

Checking Engine Oil

Figure 10-110-2

Figure 10-110-1

1

2 P13624

Check the engine oil level every day before starting the engine for the work shift. Open the rear door and remove the dipstick (Item 1) [Figure 10-110-1]. Keep the oil level between the marks on the dipstick. 1

Use a good quality motor oil that meets API Service Classification of CD or better (See Oil Chart on Page 10110-1.)

P10689

Install the dipstick and close the rear door. (See SERVICE SCHEDULE on Page 10-70-1.) for the service interval for replacing the engine oil and filter.

Oil Chart RECOMMENDED SAE VISCOSITY NUMBER (LUBRICATION OILS FOR DIESEL ENGINE CRANKCASE)

Run the engine until it is at operating temperature. Stop the engine. Open the rear door. Remove the cap (Item 1) [Figure 10-110-2] from the end of the hose and drain the oil into a container. Dispose of used oil in an environmentally safe manner. Remove the filter (Item 2) [Figure 10-110-2]. Clean the filter housing surface. Put clean oil on the gasket of the new filter. Install the filter and hand tighten. Install the cap on the drain hose and tighten.

*

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE(DIESEL ENGINES MUST USE API CLASSIFICATION CD, CF4, CG4) Can be used ONLY when available with appropriate diesel rating.

10-110-1

553 Bobcat Loader Service Manual


ENGINE LUBRICATION SYSTEM (CONT’D) Replacing Oil And Filter (Cont’d) Figure 10-110-3

1 1

P-10677

P10689

Remove the oil fill cap (Item 1) [Figure 10-110-3]. Use a good quality motor oil that meets API Service Classification of CD or better. (See Oil Chart on Page 10110-1.) Fill to capacity. (See Capacities on Page SPEC-10-4.) Start the engine and let it run for about 5 minutes. Check for leaks at the filter. Check the oil level. Add oil until the level is at the FULL mark on the dipstick. Install the oil fill cap (Item 1) [Figure 10-110-3]. NOTE: DO NOT overfill the crankcase. Record the operating hours of the loader on the decal inside the rear door. Close the rear door before operating the loader. 10-110-2

553 Bobcat Loader Service Manual


Figure 10-120-2

HYDRAULIC/HYDROSTATIC SYSTEM Description The hydraulic and hydrostatic systems use the same hydraulic fluid reservoir. The system has an engine driven pump that supplies fluid to the control valve, lift and tilt cylinders.

1

Fluid also goes from the control valve to the hydrostatic transmission pumps to provide charge pressure and cooling. A filter is installed on the right side of the engine compartment. This filter cleans the fluid for the hydrostatic transmission. The oil cooler is under the radiator. The oil cooler cools the hydraulic fluid before it returns to the hydrostatic pump.

P10697

Remove the filler cap (Item 1) [Figure 10-120-2]. Add fluid to the reservoir until it shows in the sight gauge [Figure 10-120-1].

Checking And Adding Fluid Install the filler cap [Figure 10-120-2]. Figure 10-120-1

1

P10693

Use only recommended fluid in the hydraulic/hydrostatic system. (See HYDRAULIC FLUID SPECIFICATIONS on Page SPEC-50-1.) Put the loader on a level surface. Lower the lift arms and put the attachment flat on the ground. Stop the engine. Hydraulic fluid must show in the sight gauge (Item 1) [Figure 10-120-1].

10-120-1

553 Bobcat Loader Service Manual


HYDRAULIC/HYDROSTATIC SYSTEM (CONT’D)

Replacing Hydraulic Fluid

Replacing The Hydraulic/Hydrostatic Filter

Figure 10-120-4

Figure 10-120-3

1 1

P10697 P10685

(See SERVICE SCHEDULE on Page 10-70-1.) for the correct service interval to replace the filter.

(See SERVICE SCHEDULE on Page 10-70-1.) for the service interval to replace the fluid. Replace the fluid if it becomes contaminated and after any major repairs. Remove the filler cap (Item 1) [Figure 10-120-4].

Stop the engine. Open the rear door. Clean the area around the filter housing and remove the filter element (Item 1) [Figure 10-120-3]. Clean the surface where the filter seal contacts the filter housing. Lubricate the rubber gasket with grease. Install the filter element and hand tighten. Operate the loader and check for leaks at the filter. Check fluid level in the reservoir and add as needed. Close the rear door.

10-120-2

553 Bobcat Loader Service Manual


HYDRAULIC/HYDROSTATIC SYSTEM (CONT’D) Replacing Hydraulic Fluid (Cont’d) Figure 10-120-5

1

P10695

Remove the screen (Item 1) [Figure 10-120-5]. Wash the screen in clean solvent. Install the screen in the hydraulic reservoir. Remove the fluid from the hydraulic reservoir. (See HYDRAULIC FLUID RESERVOIR on Page 20-80-1.) Remove the filter element. Install a new filter element. (See Replacing The Hydraulic/Hydrostatic Filter on Page 10-120-2.) Add hydraulic/hydrostatic fluid to the reservoir. (See HYDRAULIC FLUID SPECIFICATIONS on Page SPEC50-1.) DO NOT fill above the sight glass. Install the filler cap. Close the rear door. Operate the loader. Stop the engine. Check the fluid level and add as needed.

WARNING AVOID INJURY OR DEATH Never service or adjust the machine when the engine is running unless instructed to do so in the manual. W-2012-0497

10-120-3

553 Bobcat Loader Service Manual


FINAL DRIVE TRANSMISSION (CHAINCASE) Checking And Adding Oil Figure 10-130-1

1

P10699

The chaincase contains the final drive sprockets and chains and uses the same type of oil as the hydraulic/ hydrostatic system. (See HYDRAULIC FLUID SPECIFICATIONS on Page SPEC-50-1.) Drive the loader on a level surface. Stop the engine. Remove the plug (Item 1) [Figure 10-130-1] from the front of the chaincase housing. If oil can be reached with the tip of the your finger through the hole the oil level is correct. If the level is low, add oil through the check plug hole until the oil flows from the hole. Install and tighten the plug.

10-130-1

553 Bobcat Loader Service Manual


AUXILIARY CONTROL LOCKBOLT Removal Figure 10-140-1

1

P10754

The auxiliary control has a lockbolt (Item 1) [Figure 10140-1] that must be removed to use the optional auxiliary hydraulics. Raise the operator cab. (See Raising The Operator Cab on Page 10-30-1.) Remove the nut and bolt (Item 1) [Figure 10-140-1] at the right hand steering lever. Lower the operator cab. (See Lowering The Operator Cab on Page 10-30-2.)

10-140-1

553 Bobcat Loader Service Manual


Figure 10-150-3

BOB-TACH Inspection And Maintenance

Bob-Tach Wedge

WARNING Bob-Tach wedges must extend through the holes in attachment. Levers must be fully down and locked. Failure to secure wedges can allow attachment to come off and cause injury or death. W-2102-0588

Wedge Must Contact Lower Edge Of Hole In The Attachment

Figure 10-150-1

B-15177

Figure 10-150-4 1 N-17033

N-17031

Move the Bob-Tach levers to engage the wedges [Figure 10-150-1]. The levers and wedges must move freely. The wedges must extend through the holes in the attachment mounting frame (Item 1) [Figure 10-150-1].

TS-1062

The spring loaded wedge (Item 1) [Figure 10-150-1] must contact the lower edge of the hole in the attachment (Item 1) [Figure 10-150-2] and [Figure 10-150-3].

Figure 10-150-2 If the wedge does not contact the lower edge of the hole [Figure 10-150-2] and [Figure 10-150-3], the attachment will be loose and can come off the Bob-Tach. Inspect the mounting frame on the attachment and the Bob-Tach, linkages and wedges for excessive wear or damage [Figure 10-150-4]. Replace any parts that are damaged, bent, or missing. Keep all fasteners tight. Look for cracked welds. Contact your Bobcat dealer for repair or replacement parts.

1

N-17034

Lubricate the wedges. (See SERVICE SCHEDULE on Page 10-70-1 and See LUBRICATION OF THE BOBCAT LOADER on Page 10-160-1)

10-150-1

553 Bobcat Loader Service Manual


Figure 10-160-3

LUBRICATION OF THE BOBCAT LOADER Procedure Figure 10-160-1

1

3

P10698

3. Lift Arm Pivot Pin (Both Sides) [Figure 10-160-3] P10694

Figure 10-160-4 Lubricate the loader as specified in the SERVICE SCHEDULE, Contents Page 10-01, for the best performance of the loader.

4

Record the operating hours each time you lubricate the Bobcat loader. Always use a good quality lithium based multi-purpose grease when you lubricate the loader. Apply lubricant until extra grease shows. Lubricate the following locations on the loader: 1. Rod End Lift Cylinder (Both Sides) [Figure 10-160-1].

P10758

Figure 10-160-2 4. Base End Tilt Cylinder (Both Sides) [Figure 10-1604].

2

P10698

2. Base End Lift Cylinder (Both Sides) [Figure 10-1602].

10-160-1

553 Bobcat Loader Service Manual


LUBRICATION OF THE BOBCAT LOADER (CONT’D) Procedure (Cont’d) Figure 10-160-5

5

6

7

P10696

5. Rod End Tilt [Figure 10-160-5] 6. Bob-Tach Pivot Pin (Both Sides) [Figure 10-160-5] 7. Bob-Tach Wedge (Both Sides) [Figure 10-160-5] Figure 10-160-6

8

P10709

8. 250 Hours: Steering Lever Shaft Bearings two [Figure 10-160-6] (The opposite end is lubricated under the cab.). Put oil in the hole of the cross shaft where the right and left steering shafts meet under the cab.

10-160-2

553 Bobcat Loader Service Manual


Thank you very much for your reading. Please Click Here Then Get More Information.

Bobcat 553 skid steer loader service repair manual sn:520311001 & above  
Bobcat 553 skid steer loader service repair manual sn:520311001 & above  
Advertisement