FOREWORD This repair manual has been prepared to provide essential information on body panel repair methods (including cutting and welding operations, but excluding painting) for the SCION tC. Applicable models: ANT10 series This manual consists of body repair methods, exploded diagrams and illustrations of the body components and other information relating to body panel replacement such as handling precautions, etc. However, it should be noted that the front fenders of the SCION model is bolted on and require no welding. When repairing, don’t cut and join areas that are not shown in this manual. Only work on the specified contents to maintain body strength. Body construction will sometimes differ depending on specifications and country of destination. Therefore, please keep in mind that the information contained herein is based on vehicles for general destinations. For the repair procedures and specifications other than collisiondamaged body components of the SCION tC refer to the repair manuals. If you require the above manuals, please contact your SCION Dealer. All information contained in this manual is the most up-to-date at the time of publication. However, specifications and procedures are subject to change without prior notice.
VIEWS OF THIS TEXT Scope of the repair work explanation
This text explains the welding panel replacement instructions from the vehicle’s white body condition. We have abbreviated the explanations of the removal and reinstallation of the equipment parts up to the white body condition and of the installation, inspection, adjustment and final inspection of equipment parts after replacing the weld panel.
Section categories
Each section has been divided as shown below. Section Title
Contents
Examples
INTRODUCTION
Explanation of general body repair. Views of weld panel replacement instructions.
Cautionary items. Views of weld panel replacement instructions.
BODY PANEL REPLACEMENT
Instructions for replacing the weld panels from the white body condition, from which bolted parts have been removed, with individual supply parts.
Front side member replacement. Quarter panel replacement.
BODY DIMENSIONS
Body aligning measurements.
Dimension diagrams.
PAINT COATING
Scope and type of anti-rust treatment, etc. together with weld panel replacement.
Under coat. Body sealer.
Abbreviation of contents in this text.
The following essential procedures have been abbreviated. When actually working, conduct this work properly. (1) Jack and lift operations. (2) Clean and wash removed parts, if necessary. (3) Visual inspection.
INTRODUCTION
IN-1
GENERAL REPAIR INSTRUCTIONS 1.
WORK PRECAUTIONS
(a) VEHICLE PROTECTION (1) When welding, protect the painted surfaces, windows, seats and carpet with heat resistant, fire-proof covers.
F10001A
(b) SAFETY (1) Never stand in direct line with the chain when using a puller on the body or frame, and be sure to attach a safety cable.
F10002A
(2) Before performing repair work, check for fuel leaks. If a leak is found, be sure to close the opening totally. (3) If it is necessary to use a flame in the area of the fuel tank, first remove the tank and plug the fuel line.
F10003A
(c)
F10004A
SAFETY WORK CLOTHES (1) In addition to the usual mechanic’s wear, cap and safety shoes, the appropriate gloves, head protector, glasses, ear plugs, face protector, dust-prevention mask, etc. should be worn as the situation demands. Code
Name
A
Dust-Prevention Mask
B
Face Protector
C
Eye Protector
D
Safety Shoes
E
Welder’s Glasses
F
Ear Plugs
G
Head Protector
H
Welder’s Gloves
INTRODUCTION
IN-2
2.
HANDLING PRECAUTIONS OF PLASTIC BODY PARTS
(1) The repair procedure for plastic body parts must conform with the type of plastic material. (2) Plastic body parts are identified by the codes in the following table. (3) When repairing metal body parts adjoining plastic body parts (by brazing, frame cutting, welding, painting etc.), consideration must be given to the property of the plastic.
Code
Material name
Heat* resistant temperature limit C ( F)
Resistance to alcohol or gasoline
Notes
AAS
Acrylonitrile Acrylic Styrene
80 (176)
Alcohol is harmless if applied only for short time in small amounts (e.g., quick wiping to remove grease).
Avoid gasoline and organic or aromatic solvents.
ABS
Acrylonitrile Butadiene Styrene
80 (176)
Alcohol is harmless if applied only for short time in small amounts (e.g., quick wiping to remove grease).
Avoid gasoline and organic or aromatic solvents.
AES
Acrylonitrile Ethylene Styrene
80 (176)
Alcohol is harmless if applied only for short time in small amounts (e.g., quick wiping to remove grease).
Avoid gasoline and organic or aromatic solvents.
ASA
Acrylonitrile Styrene Acrylate
80 (176)
Alcohol is harmless if applied only for short time in small amounts (e.g., quick wiping to remove grease).
Avoid gasoline and organic or aromatic solvents.
CAB
Cellulose Acetate
80 (176)
Alcohol is harmless if applied only for short time in small amounts (e.g., quick wiping to remove grease).
Avoid gasoline and organic or aromatic solvents.
EPDM
Ethylene Propylene
100 (212)
Alcohol is harmless. Gasoline is harmless if applied only for short time in small amounts.
Most solvents are harmless but avoid dipping in gasoline, solvents, etc.
FRP
Fiber Reinforced Plastics
180 (356)
Alcohol and gasoline are harmless.
Avoid alkali.
EVA
Ethylene Acetate
70 (158)
Alcohol is harmless if applid only for short time in small amounts (e.g., quick wiping to remove grease).
Avoid gasoline and organic or aromatic solvents.
E / VAC
Ethylene / Vinyl Acetate Copolymer Resin
70 (158)
Alcohol is harmless if applid only for short time in small amounts (e.g., quick wiping to remove grease).
Avoid gasoline and organic or aromatic solvents.
PA
Polyamide (Nylon)
80 (176)
Alcohol and gasoline are harmless.
Avoid battery acid.
PBT
Polybutylene Terephthalate
160 (320)
Alcohol and gasoline are harmless.
Most solvents are harmless.
PC
Polycarbonate
120 (248)
Alcohol is harmless.
Avoid gasoline brake fluid, wax, wax removers and organic solvents. Avoid alkali.
*Temperatures higher than those listed here may result in material deformation during repair.
INTRODUCTION
Code
Material name
Heat* resistant temperature limit C ( F)
Resistance to alcohol or gasoline
IN-3
Notes
PE
Polyethylene
80 (176)
Alcohol and gasoline are harmless.
Most solvents are harmless.
PET
Polyethylene Terephthalate
75 (167)
Alcohol and gasoline are harmless.
Avoid dipping in water.
PMMA
Polymethyl Methacrylate
80 (176)
Alcohol is harmless if applied only for short time in small amounts.
Avoid dipping or immersing in alcohol, gasoline, solvents, etc.
Polyoxymethylene (Polyacetal)
100 (212)
Alcohol and gasoline are harmless.
Most solvents are harmless.
PP
Polypropylene
80 (176)
Alcohol and gasoline are harmless.
Most solvents are harmless.
PPF
Composite Reinforced Polypropylene
80 (176)
Alcohol and gasoline are harmless.
Most solvents are harmless.
PPO
Modified Polyphenylene Oxide
100 (212)
Alcohol is harmless.
Gasoline is harmless if applied only for quick wiping to remove grease.
Polystyrene
60 (140)
Alcohol and gasoline are harmless if applied only for short time in small amounts.
Avoid dipping or immersing in alcohol, gasoline, solvents, etc.
PUR
Polyurethane
80 (176)
Alcohol is harmless if applied only for very short time in small amounts (e.g., quick wiping to remove grease).
Avoid dipping or immersing in alcohol, gasoline, solvents, etc.
PVC
Polyvinylchloride (Vinyl)
80 (176)
Alcohol and gasoline are harmless if applied only for short time in small amounts (e.g., quick wiping to remove grease).
Avoid dipping or immersing in alcohol, gasoline, solvents, etc.
SAN
Styrene Acrylonitrile
80 (176)
Alcohol is harmless if applied only for short time in small amounts (e.g., quick wiping to remove grease).
Avoid dipping or immersing in alcohol, gasoline, solvents etc.
TPO
Thermoplastic Olefine
80 (176)
Alcohol is harmless. Gasoline is harmless if applied only for short time in small amounts.
Most solvents are harmless but avoid dipping in gasoline, solvents, etc.
TPU
Thermoplastic Polyurethane
80 (176)
Alcohol is harmless if applied only for short time in small amounts (e.g., quick wiping to remove grease).
Avoid dipping or immersing in alcohol, gasoline, solvents, etc.
TOYOTA Super Olefine Polymer
80 (176)
Alcohol and gasoline are harmless.
Most solvents are harmless.
Unsaturated Polyester
110 (233)
Alcohol and gasoline are harmless.
Avoid alkali.
POM
PS
TSOP
UP
*Temperatures higher than those listed here may result in material deformation during repair.
INTRODUCTION
IN-4
3.
LOCATION OF PLASTIC BODY PARTS Parts Name
Code
Radiator Grille
ABS
Radiator Lower Grille
TSOP
Front Bumper Cover
TSOP
Front Bumper Hole Cover
TSOP
Front Bumper Guard Cover
TSOP
Headlight
PC/PP
Cowl Top Ventilator Louver
TSOP
Outer Rear View Mirror
ASA/ABS
Front Door Outside Handle
PC/PBT
Side Mudguard
TSOP
Center Stop Light
PMMA/ABS
Back Door Outside Garnish
ABS
License Plate Light
PC
Rear Combination Light
PMMA/PC /ASA
Rear Bumper Cover
TSOP HINT: Resin material differs with model. / Made up of 2 or more kinds of materials.
INTRODUCTION
IN-5
HOW TO USE THIS MANUAL 1.
BODY PANEL REPLACEMENT THIS MANUAL
F13890A
IN-6
INTRODUCTION
F13891A
INTRODUCTION
2.
IN-7
SYMBOLS
The following symbols are used in the welding diagrams in section BP of this manual to indicate cutting areas and the types of weld required.
F13893A
INTRODUCTION
IN-8
SYMBOLS
—
MEANING
ILLUSTRATION
Assembly Mark
—
—
BODY SEALER (Flat Finishing)
—
BODY SEALER (No flat Finishing)
F13894A
INTRODUCTION
IN-9
3. ILLUSTRATION OF WELD POINT SYMBOLS EXAMPLE:
F13892A
INTRODUCTION
IN-10
PROPER AND EFFICIENT WORK PROCEDURES
1.
REMOVAL
(a) PRE-REMOVAL MEASURING (1) Before removal or cutting operations, take measurements in accordance with the dimension diagram. Always use a puller to straighten a damaged body or frame.
F10007A
(b) CUTTING AREA (1) Always cut in a straight line and avoid reinforced area.
F10008A
(c)
PRECAUTIONS FOR DRILLING OR CUTTING (1) Check behind any area to be drilled or cut to insure that there are no hoses, wires, etc., that may be damaged. HINT: See “Handling Precautions on Related Components” on page IN-15.
F10009A
(d) REMOVAL OF ADJACENT COMPONENTS (1) When removing adjacent components, apply protective tape to the surrounding body and your tools to prevent damage. HINT: See “Handling Precautions on Related Components” on page IN-15.
F10010A
INTRODUCTION
2.
IN-11
PREPARATION FOR INSTALLATION
(a) SPOT WELD POINTS (1) When welding panels with a combined thickness of over 3 mm (0.12 in.), use a MIG (Metal Inert Gas) welder for plug welding. HINT: Spot welding will not provide sufficient durability for panels over 3 mm (0.12 in.) thick. F10011A
(b) APPLICATION OF WELD-THROUGH PRIMER (SPOT SEALER) (1) Remove the paint from the portion of the new parts and body to be welded, and apply weld-through primer.
F10012A
(c)
MAKING HOLES FOR PLUG WELDING (1) For areas where a spot welder cannot be used, use a puncher or drill to make holes for plug welding. REFERENCE: mm (in.) Thickness of welded portion
Size of plug hole
1.0 (0.04) under
5 (0.20) ø over
1.0 (0.04) − 1.6 (0.06)
6.5 (0.26) ø over
1.7 (0.07) − 2.3 (0.09)
8 (0.31) ø over
2.4 (0.09) over
10 (0.39) ø over
F10013A
(d) SAFETY PRECAUTIONS FOR ELECTRICAL COMPONENTS (1) When welding, there is a danger that electrical components will be damaged by the electrical current flowing through the body. (2) Before starting work, disconnect the negative terminal of the battery and ground the welder near the welding location of the body. F10014A
(e) ROUGH CUTTING OF JOINTS (1) For joint areas, rough cut the new parts, leaving 20 − 30 mm (0.79 − 1.18 in.) overlap.
F10015A
INTRODUCTION
IN-12
3.
INSTALLATION
(a) PRE-WELDING MEASUREMENTS (1) Always take measurements before installing underbody or engine components to insure correct assembly. After installation, confirm proper fit.
F10016A
(b) WELDING PRECAUTIONS (1) The number of welding spots should be as follows. Spot weld: 1.3 X No. of manufacturer’s spots. Plug weld: More than No. of manufacturer’s plugs. (2) Plug welding should be done with a MIG (Metal Inert Gas) welder. Do not gas weld or braze panels at areas other than specified.
F10017A
(c)
POST-WELDING REFINISHING (1) Always check the welded spots to insure they are secure. (2) When smoothing out the weld spots with a disc grinder, be careful not to grind off too much as this would weaken the weld.
F10018A
(d) SPOT WELD LOCATIONS (1) Try to avoid welding over previous spots.
F10020A
(e) SPOT WELDING PRECAUTIONS (1) The shape of the welding tip point has an effect on the strength of the weld. (2) Always insure that the seams and welding tip are free of paint.
F10019A
INTRODUCTION
4.
IN-13
ANTI-RUST TREATMENT
(a) BODY SEALER APPLICATION (1) For water-proofing and anti-corrosion measures, always apply the body sealer to the body panel seams and hems of the doors, hoods, etc.
F10021A
(b) UNDERCOAT APPLICATION (1) To prevent corrosion and protect the body from damage by flying stones, always apply sufficient undercoat to the bottom surface of the under body and inside of the wheel housings.
F10022A
5.
ANTI-RUST TREATMENT AFTER PAINTING PROCESS
(a) ANTI-RUST AGENT (WAX) APPLICATION (1) To preserve impossible to paint areas from corrosion, always apply sufficient anti-rust agent (wax) to the inside of the hemming areas of the doors and hoods, and around the hinges, or the welded surfaces inside the boxed cross-section structure of the side member, body pillar, etc. F10023A
INTRODUCTION
IN-14
6.
ANTI-RUST TREATMENT BY PAINTING REFERENCE:
Painting prevents corrosion and protect the sheet metal from damage. In this section, anti-chipping paint only for anti-corrosion purpose is described. (a) ANTI-CHIPPING PAINT (1) To prevent corrosion and protect the body from damage by flying stones, etc., apply anti-chipping paint to the rocker panel, wheel arch areas, balance panel, etc. HINT: Depending on the model or the application area, there are cases where the application of anti-chipping paint is necessary before the second coat or after the top coat. Apply the anti-chipping paint after the top coat.
Apply the anti-chipping paint before the second coat. Anti-Chipping Paint
Top Coat Second Coat
Top Coat Second Coat
Anti-Chipping Paint
Under Coat (ED Primer)
Under Coat (ED Primer)
Steel Metal
Steel Metal F10024A
INTRODUCTION
IN-15
HANDLING PRECAUTIONS ON RELATED COMPONENTS 1.
BRAKE SYSTEM The brake system is one of the most important safety components. Always follow the directions and notes given in brake (32) section of the repair manual for the relevant model when handling brake system parts. NOTICE: When repairing the brake master cylinder or TRAC system, bleed the air out of the TRAC system.
2.
DRIVE TRAIN AND CHASSIS The drive train and chassis are components that can have great effects on the running performance and vibration resistance of the vehicle. After installing components in the sections listed in the table below, perform alignments to ensure correct mounting angles and dimensions. Particularly accurate repair of the body must also be done to ensure correct alignment. HINT: Correct procedures and special tools are required for alignment. Always follow the directions given in the repair manual for the relevant model during alignment and section DI of this section.
3.
Component to be aligned
Section of repair manual for relevant model
Front Wheels
Front Suspension (26) section
Rear Wheels
Rear Suspension (27) section
COMPONENTS ADJACENT TO THE BODY PANELS Various types of component parts are mounted directly on or adjacently to the body panels. Strictly observe the following precautions to prevent damaging these components and the body panels during handling. Before repairing the body panels, remove their components or apply protective covers over the components. Before prying components off using a screwdriver or a scraper, etc., attach protective tape to the tool tip or blade to prevent damaging the components and the body paint. Before removing components from the outer surface of the body, attach protective tape to the body to ensure no damage to painted areas. HINT: Apply touch-up paint to any damaged paint surfaces. Before drilling or cutting sections, make sure that there are no wires, etc. on the reverse side.
4.
ECU (ELECTRONIC CONTROL UNIT) Many ECUs are mounted in this vehicle. Take the following precautions during body repair to prevent damage to the ECUs. Before starting electric welding operations, disconnect the negative (−) terminal cable from the battery. When the negative (−) terminal cable is disconnected from the battery, memory of the clock and audio systems will be cancelled. So before starting work, make a record of the contents memorized by each memory system. Then when work is finished, reset the clock and audio systems as before. When the vehicle has tilt and telescopic steering, power seat and outside rear view mirror, which are all equipped with memory function, it is not possible to make a record of the memory contents. So when the operation is finished, it will be necessary to explain this fact to the customer, and request the customer to adjust the features and reset the memory. Do not expose the ECUs to ambient temperatures above 80 C (176 F). NOTICE: If it is possible the ambient temperature may reach 80 C (176 F) or more, remove the ECUs from the vehicle before starting work. Be careful not to drop the ECUs and not to apply physical shocks to them.
IN-16
INTRODUCTION
PRECAUTIONS FOR REPAIRING BODY STRUCTURE PANELS
1.
HEAT REPAIR FOR BODY STRUCTURE PANELS Toyota prohibits the use of the heat repair method on body structure panels when repairing a vehicle damaged in a collision. Panels that have high strength and rigidity, as well as a long life span for the automobile body are being sought after. At Toyota, in order to fulfill these requirement, we use high tensile strength steel sheets and rust preventive steel sheets on the body. High tensile steel sheets are made with alloy additives and a special heat treatment in order to improve the strength. To prevent the occurrence of rust for a long period of time, the surface of the steel is coated with a zinc alloy. If a body structure parts are heat repaired with an acetylene torch or other heating source, the crystalline organization of the steel sheet will change and the strength of the steel sheet will be reduced. The ability of the body to resist rust is significantly lowered as well since the rust resistant zinc coating is destroyed by heat and the steel sheet surface is oxidized.
2.
STRUCTURE PANEL KINKS A sharp deformation angle on the panel that cannot be returned to its original shape by pulling or hammering is called kink. Since structure parts are designed to exhibit its performance in their original shape, if parts are deformed in an accident, or if the deformed parts are repaired and reused, the parts may become unable to exhibit the same performance as intended in the design. It is necessary to replace the part where the kink has occurred.
INTRODUCTION
3.
IN-17
IMPACT BEAM REPAIR The impact beam and bracket are necessary and important parts that help reduce the probability of injury to passengers in side collisions. For impact beam, we use special high tensile strength steel. The high tensile strength steel maintains its special crystalline organization by heat treatment or alloy additives. Since these parts are designed to exhibit its performance in their original shape, if parts are deformed in an accident, or if the deformed parts are repaired and reused, the parts may become unable to exhibit the same performance as intended in the design. If the impact beam or bracket is damaged, replace the door assembly which has the damaged beam. Also, the bumper reinforcement is a necessary and important part that helps reduce the probability of injury to passengers in front collisions, and for the same reasons explained above, should be replaced if damaged.
IN-18
INTRODUCTION
ABBREVIATIONS USED IN THIS MANUAL For convenience, the following abbreviations are used in this manual. ABS Antilock Brake System A/C Air Conditioner assy assembly ECT Electronic Controlled Transmission ECU Electronic Control Unit e.g. Exempli Gratia (for Example) Ex. Except FWD Front Wheel Drive Vehicles 2WD Two Wheel Drive Vehicles 4WD Four Wheel Drive Vehicles in. inch LH Left-hand LHD Left-hand Drive MIG Metal Inert Gas M/Y Model Year PPS Progressive Power Steering RH Right-hand RHD Right-hand Drive SRS Supplemental Restraint System SSM Special Service Materials w/ with w/o without
BODY PANEL REPLACEMENT
IN-85
FIT STANDARDS
F20186
3.4 mm (0.134 in.)
4.0 mm (0.157 in.)
4.3 mm (0.169 in.)
4.85 mm (0.191 in.)
5.08 mm (0.200 in.)
5.1 mm (0.201 in.)
5.15 mm (0.203 in.)
—
—
IN-86
BODY PANEL REPLACEMENT
F20187
3.1 mm (0.122 in.)
4.5 mm (0.177 in.)
4.85 mm (0.191 in.)
5.05 mm (0.199 in.)
5.85 mm (0.230 in.)
7.0 mm (0.276 in.)
BODY PANEL REPLACEMENT
BP-1
RADIATOR UPPER SUPPORT (ASSY) REPLACEMENT
F20102A
REMOVAL
F20102
POINT 1 Remove the [A] at the same time. PART NAME [A] Front Bumper Stay
BODY PANEL REPLACEMENT
BP-2
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20103
PART NAME [A] Front Bumper Stay
[B]
Radiator Support Reinforcement
BODY PANEL REPLACEMENT
BP-3
F20101
POINT 1 Measure the dimensions before installing the headlights. 2 These values are reference values. 154 mm (6.06 in.)
175 mm (6.89 in.)
181 mm (7.13 in.)
1055 mm (41.54 in.)
BP-4
BODY PANEL REPLACEMENT
RADIATOR SUPPORT UPPER BRACE (ASSY) REPLACEMENT With the radiator upper support removed.
F20104A
REMOVAL
F20104
BODY PANEL REPLACEMENT
BP-5
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20105
PART NAME [A] Front Bumper Side Mounting Bracket
BP-6
BODY PANEL REPLACEMENT
FRONT CROSSMEMBER (ASSY) REPLACEMENT
F20106A
REMOVAL
F20106
BODY PANEL REPLACEMENT
BP-7
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20107
BP-8
BODY PANEL REPLACEMENT
RADIATOR SUPPORT (ASSY) REPLACEMENT
F20108A
REMOVAL
F20108
BODY PANEL REPLACEMENT
BP-9
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20109
BP-10
BODY PANEL REPLACEMENT
FRONT FENDER FRONT APRON WITH SUPPORT (ASSY) REPLACEMENT With the radiator upper support removed. F20110A
REMOVAL
F20110
BODY PANEL REPLACEMENT
BP-11
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20111
BP-12
BODY PANEL REPLACEMENT
FRONT FENDER APRON (ASSY) REPLACEMENT With the radiator upper support and cowl top side panel removed.
F20112A
REMOVAL
F20112
BODY PANEL REPLACEMENT
BP-13
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20113
POINT 1 Inspect the fitting of the front fender and hood, etc,. before welding, since this affects the appearance of the finish. 2 Make sure each measurement is corect, as this parts affects the front wheel alignment. 15 mm (0.59 in.)
BP-14
BODY PANEL REPLACEMENT
FRONT SIDEMEMBER (CUT-P) REPLACEMENT With the radiator support upper brace and front crossmember removed.
F20114A
REMOVAL
F20114
80 mm (3.15 in.)
BODY PANEL REPLACEMENT
BP-15
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20115
PART NAME [A] Front Bumper Arm Retainer
BP-16
BODY PANEL REPLACEMENT
FRONT SIDEMEMBER (ASSY) REPLACEMENT With the radiator support upper brace, front crossmember and front fender apron removed. F20116A
REMOVAL
F20116
POINT 1 After removing the [A], remove the front sidemember. PART NAME [A] Front Sidemember Outer Plate
BODY PANEL REPLACEMENT
BP-17
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20117
POINT 1 Make sure each measurement is corect, as this parts affects the front wheel alignment. PART NAME [B] [A] Front Sidemember Outer Plate 20 mm (0.79 in.) 30 mm (1.18 in.)
Front Bumper Mounting Reinforcement 90 mm (3.54 in.)
BP-18
BODY PANEL REPLACEMENT
COWL TOP SIDE PANEL (ASSY) REPLACEMENT
F20118A
REMOVAL
F20118
POINT 1 Remove the [A] at the same time. PART NAME [A] Cowl Top To Apron Brace
BODY PANEL REPLACEMENT
BP-19
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20119
PART NAME [A] Cowl Top To Apron Brace
15 mm (0.59 in.)
BP-20
BODY PANEL REPLACEMENT
COWL TOP UPPER SIDE PANEL (ASSY) REPLACEMENT
F20120A
REMOVAL
F20120
BODY PANEL REPLACEMENT
BP-21
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20121
10 mm (0.39 in.)
BP-22
BODY PANEL REPLACEMENT
0
FRONT BODY PILLAR (CUT) REPLACEMENT With the cowl top side panel removed.
F20122A
REMOVAL
F20122
POINT 1 [A]: Reuse PART NAME [A] Rocker Outer Panel 40 mm (1.57 in.) 215 mm (8.46 in.)
300 mm (11.81 in.)
BODY PANEL REPLACEMENT
BP-23
F20123
BP-24
BODY PANEL REPLACEMENT
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20124
POINT 1 Before temporarily installing the new parts, weld the [B], [C], [D] and [E] with standard points. PART NAME [C] Front Body Pillar Lower Reinforce [D] Front Body Inner Pillar [B] Rocker Outer Reinforcement [E] Outer Pillar 10 mm (0.39 in.) 15 mm (0.59 in.) 255 mm (10.04 in.)
BODY PANEL REPLACEMENT
BP-25
F20125
POINT 1 Inspect the fitting of the front door, front fender and windshield glass, etc., before welding, since this affects the appearance of the finish. 2 *1: Reference value PART NAME [F] No.6 Pillar Outer Bracket
67 mm (2.64 in.)
BP-26
BODY PANEL REPLACEMENT
F20126
10 mm (0.39 in.)
15 mm (0.59 in.)
BODY PANEL REPLACEMENT
BP-27
FRONT DOOR OUTER PANEL (ASSY) REPLACEMENT
F20180A
REMOVAL
F20180
POINT 1 Before removing the outer panel, mark the installation position with a tape. 2 Before removing the outer panel, establish its exact position inrelation to the window frame using a reference marker, etc. 3 After grinding off the hemming location, remove the outer panel.
BP-28
BODY PANEL REPLACEMENT
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20182
POINT 1 Before temporarily installing the new parts, apply body sealer to the reinforcement, side impact protection beam and backside of the new parts. HINT: 1) Apply sealer evenly about 10 mm (0.39 in.) from the flange and 3 mm (0.12 in.) in diameter to the outer panel and apply just enough sealer for the reinforcement and side impact protection beam to make contact. 2 Bend the flange hem about 30 with a hammer and dolly, then fasten tightly with a hemming tool. HINT: 1) Perform hemming in three steps, being careful not to warp the panel. 2) If a hemming tool cannot be used, hem with a hammer and dolly.
BODY PANEL REPLACEMENT
BP-29
ROCKER PANEL (CUT) REPLACEMENT
F20127A
REMOVAL
F20127
POINT 1 Remove the [A] at the same time. PART NAME [A] Rocker Outer Reinforcement 40 mm (1.57 in.) 140 mm (5.51 in.)
BP-30
BODY PANEL REPLACEMENT
INSTALLATION Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram) Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish. After welding, apply the polyurethane foam to the corresponding parts. After welding, apply body sealer and under-coating to the corresponding parts. After applying the top coat layer, apply anti-rust agent to the inside of the necked section structural weld spots.
F20128
POINT 1 Inspect the fitting of the front door, etc., before welding, since this affects the appearance of the finish. PART NAME [A] Rocker Outer Reinforcement 255 mm (10.04 in.) 480 mm (18.90 in.)
BODY PANEL REPLACEMENT
BP-31
ROCKER OUTER REINFORCEMENT (CUT-H) REPLACEMENT With the quarter panel removed.
F20129A
REMOVAL
F20129
POINT 1 [B]: Reuse PART NAME [B] [A] Center Body Pillar Reinforcement 40 mm (1.57 in.) 200 mm (7.87 in.)
Rocker Outer Panel 265 mm (10.43 in.)
BP-32
BODY PANEL REPLACEMENT
F20130
Thank you very much for your reading. Please Click Here Then Get More Information.