Liebherr TL 445-10 Telescopic Handler Service Repair Manual by 1632723

 

      

 

    

 

    

  

  



              

  

                           

     

           

Service Manual Table of contents

0.1.000 Table of contents Title

Date of issue

0.1.000

Table of contents

03.2010

1.0.000 1.1.000 1.2.000 1.3.001 1.3.002 1.3.003 1.4.000 1.5.000

Sub group index "General" Foreword and explanations Safety guidelines Tightening torques Conversion charts Tapping holes Conservation guidelines Material weights

05.2007 10.2007 02.2008 02.2010 01.2009 05.2007 02.2010 01.2010

2.0.000 2.1.000 2.2.000 2.3.000

Sub group index "Tools and work instructions" Special tools Repair welding Assembly instructions

08.2007 03.2010 08.2007 01.2009

3.0.000 3.1.000 3.1.001 3.2.000 3.2.001 3.3.000 3.4.000 3.5.000

Sub group index "Technical data and Maintenance guidelines" Technical data Technical data Maintenance and inspection schedule Maintenance and inspection schedule Maintenance and inspection guidelines Adjustment check list Inspection and adjustment tasks

10.2007 01.2010 01.2010 02.2009 01.2010 01.2010 01.2010 01.2010

4.0.000 4.1.000 4.1.001 4.2.000 4.3.000 4.4.000

Sub group index "Engine" Data page Data page Fan and cylinder arrangement Installation kit Liebherr- Diesel particle filter Installation and check list for Diesel particle filter

01.2009 01.2010 01.2010 01.2010 01.2009 01.2009

5.0.000 5.1.000 5.2.000 5.3.000

Sub group index "Coupling, splitterbox" Data page Coupling Splitterbox

03.2007 01.2010 06.2007 10.2007

6.0.000 6.1.000 6.2.000 6.2.001 6.3.000 6.3.001 6.4.000 6.5.000 6.5.001

Sub group index "Travel hydraulic" Data page Design Design Function Function Repair work and troubleshooting Component arrangement Component arrangement

10.2007 01.2010 10.2007 02.2010 02.2010 02.2010 10.2007 08.2007 05.2007

Page No.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

0.1.000 - 1 / 4

Service Manual Table of contents

Title

Date of issue

7.0.000 7.1.000 7.2.000 7.2.001 7.3.000 7.3.001 7.4.000 7.5.000

Sub group index "Working hydraulic" Data page Design Design Function Function Repair work and troubleshooting Component arrangement

10.2007 01.2010 10.2007 03.2009 03.2009 03.2009 10.2007 10.2007

8.0.000 8.1.000 8.2.000 8.3.000 8.3.001 8.4.000 8.5.000

Sub group index "Steering hydraulic" Data page Design Function Function Repair work and troubleshooting Component arrangement

10.2007 01.2010 08.2007 03.2009 03.2009 10.2007 08.2007

9.0.000 9.1.000 9.2.000 9.2.001 9.3.000 9.3.001 9.4.000 9.5.000 9.5.001

Sub group index "Brake hydraulic" Data page Design Design Function Function Repair work and troubleshooting Component arrangement Component arrangement

10.2007 01.2010 08.2007 01.2010 03.2009 01.2010 10.2007 05.2007 01.2010

Sub group index "Hydraulic components" Var. displacement pump / Travel pump – Travel hydraulic Var. displacement motor/ Travel motor - Travel hydraulic Regulating pump - Working hydraulic Regulating pump - Working hydraulic Fixed displacement pump Gear motor – fan drive Steering aggregate Proportional control valve block Black / white control valve block Black / white control valve block Brake cylinder Valves Cylinders

05.2007 03.2007 03.2007 06.2007 01.2009 05.2007 10.2007 05.2007 03.2007 02.2010 02.2010 02.2010 02.2009 02.2009

Sub group index "Electrical system – Diagrams and components" Component description Component description Function list Function list Fuses, notes Circuit diagram Circuit diagram Component arrangement Component arrangement Control lever Calibration of the electronic load display Calibration of the electronic load display DMS Sensor installation

05.2007 01.2010 01.2010 01.2010 01.2010 01.2009 01.2009 01.2009 01.2009 03.2009 01.2009 06.2007 10.2007 10.2007

Page No.

10.0.000 10.1.000 10.2.000 10.3.000 10.3.001 10.4.000 10.5.000 10.6.000 10.7.000 10.8.000 10.8.001 10.9.000 10.10.000 10.11.000 11.0.000 11.1.000 11.1.001 11.2.000 11.2.001 11.3.000 11.4.000 11.4.001 11.5.000 11.5.001 11.6.000 11.7.000 11.7.001 11.8.000

0.1.000 - 2 / 4

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual Table of contents

Title

Date of issue

12.0.000 12.1.000 12.1.001 12.2.000 12.2.001 12.3.000 12.4.000

Sub group index "Electrical system - Descriptions" Evaluation software Travel hydraulic LinDiag Evaluation software Travel hydraulic LinDiag Software Working hydraulic control Bodem Software Working hydraulic control Bodem Service-Code list Software PDL – Diesel particle filter

01.2009 01.2010 01.2010 01.2010 02.2010 02.2010 01.2010

13.0.000 13.1.000 13.2.000 13.3.000 13.4.000 13.5.000 13.6.000

Sub group index "Axles / tires and gear shafts" Data page Design Disk brake Differential Wheel hub and steering axle Gear shafts

10.2007 01.2010 01.2010 01.2010 04.2007 02.2009 06.2007

14.0.000 14.1.000 14.1.001 14.1.002 14.2.130 14.2.131 14.2.132 14.3.000 14.3.001 14.4.000 14.5.000

Sub group index "Main frame installations" Level regulation Level regulation Level regulation Stabilizer / side offset Stabilizer / side offset Stabilizer / side offset Cooler arrangement Cooler arrangement Engine mount Battery installation

03.2007 03.2009 02.2010 02.2010 03.2009 02.2010 02.2010 05.2007 05.2007 08.2007 03.2007

15.0.000 15.1.000 15.1.001 15.2.000

Sub group index "Tank arrangements" Hydraulic tank Hydraulic tank Fuel tank

03.2007 10.2007 03.2009 08.2007

16.0.000 16.1.000 16.2.000 16.3.000

Sub group index "Operator’s cab, heater, air conditioning system" Operator’s cab Heater and blower Air conditioning system

03.2007 08.2007 08.2007 01.2009

17.0.000 17.1.100 17.1.101 17.1.130 17.1.131 17.2.100 17.2.101 17.2.130 17.2.131

Sub group index "Telescopic boom" Design and function Design and function Design and function Design and function Repair instructions Repair instructions Repair instructions Repair instructions

06.2007 10.2007 06.2007 06.2007 06.2007 02.2008 02.2008 03.2010 03.2010

18.0.000 18.1.000 18.2.000 18.3.000 18.4.100 18.4.130 18.4.131

Sub group index "Working attachment" Tool coupler Forklift Bucket Aerial work platform Aerial work platform Aerial work platform

10.2007 01.2009 08.2007 03.2010 02.2010 02.2010 02.2010

Page No.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

0.1.000 - 3 / 4

Service Manual Table of contents

Title

Date of issue

19.0.000 19.1.000 19.1.001 19.2.000 19.4.000 19.5.000 19.6.000 19.7.000

Sub group index "Special equipment" Industrial control Industrial control Rear axle steering Quick coupler Reversible fan Towing hitch device Telescope - Leak oil line

03.2010 03.2009 03.2009 06.2007 04.2007 03.2009 01.2010 03.2010

20.0.00 6.3.000 6.3.001 7.3.000 7.3.001 8.3.000 8.3.001 9.3.000 9.3.001 11.4.000 11.4.001 14.1.000 14.1.001 14.1.002 14.2.130 14.2.131 14.2.132 18.4.100 18.4.130 18.4.131 19.1.000 19.1.001

Sub group index "Additional documentation" Schematic Travel hydraulic Schematic Travel hydraulic Schematic Working hydraulic Schematic Working hydraulic Schematic Steering hydraulic Schematic Steering hydraulic Schematic Brake hydraulic Schematic Brake hydraulic Circuit diagram Circuit diagram Schematic Level regulation Schematic Level regulation Schematic Level regulation Schematic Stabilizers and side offset Schematic Stabilizers and side offset Schematic Stabilizers and side offset Schematic Aerial work platform Schematic Aerial work platform Schematic Aerial work platform Schematic Industrial control Schematic Industrial control

10.2007 02.2010 02.2010 03.2009 03.2009 03.2009 03.2009 03.2009 01.2010 01.2009 01.2009 03.2009 02.2010 02.2010 02.2010 02.2010 02.2010 02.2010 01.2009 03.2009 03.2009 03.2009

Page No.

0.1.000 - 4 / 4

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

General Sub group index - General

1 General 1.0.000 Sub group index - General Foreword and explanations .............................................................................. 1.1 Safety guidelines ............................................................................................... 1.2 Charts ................................................................................................................. 1.3 Tightening torques ..........................................................................................................1.3.001 Conversion charts...........................................................................................................1.3.002 Tapping holes .................................................................................................................1.3.003

Conservation guidelines ................................................................................... 1.4 Material weights................................................................................................. 1.5

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Mjfcifss!

1.0.000 - 1 / 2

Service Manual

General Foreword and explanations

1.1.000 Foreword and explanations 1

For information This manual contains technical data, design and functional descriptions, work and adjustment instructions as well as numerous drawings, functional views and illustrations for the LIEBHERR â&#x20AC;&#x201C; Telescopic loader. This manual should simplify competent customer service of our products. However, it does not replace expert and qualified user training and attendance of our factory training classes. Generally valid basic information is not listed. Refer to separate documentation for operational and spare parts information. The manual will be updated and expanded as necessary when changes occur in series. Note! This symbol is used in the manual for very important notes. For all tasks on the machine, accident prevention guidelines and safety guidelines must be strictly observed. Note! This manual is solely for the own use of the registered owner and may not be duplicated or copied, complete or in part, nor passed on to a third person and remains the property of LIEBHERR-Werk Telfs GmbH. All rights reserved - Printed in Austria. We reserve the right to make changes of technical details on the machine in comparison to the information and illustrations in this manual. Written and published by LIEBHERR-Werk Telfs GmbH., Technical Documentation Dept.

Explanation of layout To make it easier to find certain information and to simplify filing of updates, the following structure was developed:

Main group

Sub group

Type group

Page No.

6.3.130 - 1/2 Components (item) groups acc. to index

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Structure of main group according to sub group index

Structure based on telescopic boom type (13) and updates (0)

Continuous running number and complete pages within the model group

MJFCIFSS!

1.1.000 - 1 / 2

General

Service Manual

Foreword and explanations

For the 3-digit type group number, the last number provides information regarding updates, whereby the two other numbers provide information about the type of machine, for example 000 and no additional machine serial number limitation means that the document is valid for all TL machine. for example 100/130 and no additional machine serial number limitation means that this document is valid for a TL 10 meter boom / TL 13 meter boom. for example 001/101/131 is a supplement which is valid from a certain machine serial number. Changes are issued with the same number, but with a later date. Updates have new numbers. If a page is valid only for a certain machine group, then this is noted in the header.

Itemization variations This symbol denotes a standard listing. This symbol means:“ The prerequisite must be met“. The maintenance personnel must first fulfill the described prerequisites, for example, to bring the machine in working position, to be able to carry out the steps described thereafter. This symbol denotes an activity step. The maintenance personnel is to become active on this point and carry out the described activity. This symbol denotes a result. The maintenance personal is alerted that there is a result after an activity step, for example after pressing the test button, the LED lights up.

General

This note shows that a detail view of an illustration is shown rotated by a given angle, as compared to the actual installation position (in this case 180°). We hope that with the enclosed information we have taken yet another step to improve the service on the LIEBHERR telescopic handlers, crawler dozers, crawler loaders and pipe layers.

LIEBHERR-Werk Telfs GmbH. Technical Documentation

1.1.000 - 2 / 2

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

General Safety guidelines

1.2.000 Safety guidelines 1 Introduction Prior to and during the performance of tests, inspections and repairs, the following safety guidelines must be observed: Any type of work may only be carried out by qualified expert personnel or under their guidance and supervision. Qualified expert personnel are persons, who, based on their specialized training and experience, have sufficient knowledge in the area of telescopic handlers and the specific technology of our machines in particular and who are familiar with all applicable laws and general work protection regulations, accident prevention guidelines, regulations, guidelines and generally approved rules concerning technology so that they are able to evaluate if the earthmoving equipment is safe to operate and if the necessary work can be performed without endangering themselves or third persons. Always adhere to the adjustment values noted in the LIEBHERR documentation when performing adjustment work. At the delivery of a machine, the operating personnel must be trained using the current operating instructions. The safety guidelines noted in the instructions must be particularly observed. These safety guidelines must also be observed during inspection, adjustment or repair work. However, there are special repair and / or inspection work which require qualified personnel to follow another procedure than that noted in the safety guidelines. In such cases, qualified personnel or individuals performing the work under the supervision of such personnel should assure that additional safety precautions necessary to insure the safety of those involved in the repair and/ or third persons are taken. Such items of repair and/ or inspection work include, but are not limited to the following: -

Opening the engine compartment doors while the engine running to carry out tests and / or adjustments. In these cases, it should be ensured that the cab door is properly secured during the entire duration of the work to prevent it from closing unexpectedly and / or inadvertently. Care should be exercised to assure that there will be no inadvertent or unintended contact of any part of the body with any moving and / or heated components. Wear only tightly fitted clothing (no scarves, no tie, no wide sleeves, etc.).

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

1.2.000 - 1 / 4

General

Service Manual

Safety guidelines

Danger notes in this manual In the description of work, which can cause dangers for man or machine, the required safety measures are described in this manual. They are denoted with the following notes:

Danger! Warns that certain working procedures without appropriate precautionary measures can result in fatal injuries. Warning! Warns that certain working procedures without appropriate precautionary measures can result in severe bodily injuries. Caution! Warns that certain working procedures without appropriate precautionary measures can result in bodily injuries or damage to the machine. Following these notes does not relieve you from observation of additional regulations and guidelines! The following must also be observed: -

the safety regulations valid for the jobsite.

those issued by the legislature "Traffic regulationsâ&#x20AC;&#x153;.

the guidelines issued by trade associations.

1.2.000 - 2 / 4

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

General Safety guidelines

Safety guidelines in these Operating instructions The detailed descriptions of the following safety guidelines are in the Operating instructions of the machine and must be strictly observed. 1

Introduction

Destined use

Signs on the machine

Safety guidelines

4.1

General safety guidelines

4.2

Crushing and burn prevention

4.3

Fire and explosion prevention

4.4

Machine start up safety

4.5

Engine start up safety

4.6

Machine operating safety

4.7

Machine parking safety

4.8

Machine transporting safety

4.9

Machine towing safety

4.10 Machine maintenance safety 4.11 Safety guidelines for welding work on the machine 4.12 Safety guidelines for working on the attachment 4.13 Safety guidelines when loading the machine with a crane 4.14 Safe maintenance of hydraulic hoses and hose lines 4.15 Safety guidelines for maintenance work on machines with hydro accumulators 4.16 Roll over protection (ROPS) and falling object protection (FOPS) 4.17 Attachment and components 4.18 Safe operation for material handling 4.19 Protection from vibration 4.20 Safety guidelines for operation with quick coupler adapter (optional)

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

1.2.000 - 3 / 4

Service Manual

General Tightening torques

1.3.001 Tightening torques The preload values and tightening torques noted in the chart have been taken from the VDI guidelines 2230 of July 1986. Installation preload values FM and tightening torques MA for shoulder studs with standard metric or fine thread per DIN ISO 262 and DIN ISO 965 T2 (replacement for DIN 13 part 13) and wrench sizes for hex head screws with shaft DIN EN 24014 (replacement for DIN 931 part 1) or socket head screws DIN EN ISO 4762 (replacement for DIN 912) -

The chart values are valid for screws with black or phosphated, zinc plated and DACROMET 500. Screws and nuts with black, phosphated or zinc plated, lightly lubricated. Medium friction value G = 0,12.

Note! Any tightening torque values and/ or tightening procedures noted in drawings / parts lists, instructions or component descriptions must be adhered to and given preference over factory standards. Beginning with grade 10.9, the use of lock washers does no longer provide any safety action. Always use correctly sized torque wrenches Â&#x2013; the torque value according to the chart should be within the upper third of the existing range. When using impact wrenches, care must be taken so that the torque values are not exceeded. Check before and intermediately with a torque wrench.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

1.3.001 - 1 / 4

General

Service Manual

Tightening torques

Preload values FM based on grades in N

Metric standard thread M M M M M M M M M M M M M M M M M M

4 5 6 7 8 10 12 14 16 18 20 22 24 27 30 33 36 39

Preload values and tightening torques with standard metric thread according to factory standard WN 4037 I

8.8

10.9

12.9

x 0,7

4 050

6 000

7 000

x 0,8

6 600

9 700

11 400

9 400

13 700

16 100

13 700

20 100

23 500

x 1,25

17 200

25 000

29 500

x 1,5

27 500

40 000

47 000

x 1,75

40 000

59 000

69 000

55 000

80 000

94 000

75 000

111 000

130 000

x 2,5

94 000

135 000

157 000

x 2,5

121 000

173 000

202 000

x 2,5

152 000

216 000

250 000

175 000

249 000

290 000

230 000

330 000

385 000

x 3,5

280 000

400 000

465 000

x 3,5

350 000

495 000

580 000

410 000

580 000

680 000

490 000

700 000

820 000

Tightening torques MA based on grades in Nm 8.8 2,8 5,5 9,5 15,5 23 46 79 125 195 280 390 530 670 1000 1350 1850 2350 3000

10.9 4,1 8,1 14,0 23,0 34 68 117 185 280 390 560 750 960 1400 1900 2600 3300 4300

12.9 4,8 9,5 16,5 27,0 40 79 135 215 330 460 650 880 1120 1650 2250 3000 3900 5100

1.3.001 - 2 / 4

Mjfcifss!

Wrench size, (x) = according to DIN931, for Socket head Hex head screw screw mm Inch mm Inch 7

9/32

5/16

5/32

1/2

(17) 16

(11/16) --

5/16

(19) 18

(3/4) --

(22) 21

(7/8) --

9/16

1-1/16

9/16

1-3/16

(32) 34

1-7/16

3/4

1-5/8

3/4

1-13/16

7/8

2-3/16

1-1/16

2-3/8

1-1/16

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

General Tightening torques

Preload values FM based on Tightening torques MA grades in N based on grades in Nm

Metric fine thread

M M M M M M M M M M M M M M M M M M M M M M M M

8 9 10 10 12 12 14 16 18 18 20 22 24 24 27 27 30 30 33 33 36 36 39 39

TL 435-10 TL 445-10 TL 435-13 TL 442-13

Preload values and tightening torques with fine metric thread according to factory standard WN 4037 I

x1 x1 x1 x 1,25 x 1,25 x 1,5 x 1,5 x 1,5 x 1,5 x2 x 1,5 x 1,5 x 1,5 x2 x 1,5 x2 x 1,5 x2 x 1,5 x2 x 1,5 x3 x 1,5 x3

8.8

10.9

12.9

18 800

27 500

32 500

24 800

36 500

42 500

31 500

46 500

54 000

29 500

43 000

51 000

45 000

66 000

77 000

42 500

62 000

73 000

61 000

89 000

104 000

82 000

121 000

141 000

110 000

157 000

184 000

102 000

146 000

170 000

139 000

199 000

232 000

171 000

245 000

285 000

207 000

295 000

346 000

196 000

280 000

325 000

267 000

381 000

445 000

255 000

365 000

425 000

335 000

477 000

558 000

321 000

457 000

534 000

410 000

584 000

683 000

395 000

560 000

660 000

492 000

701 000

820 000

440 000

630 000

740 000

582 000

830 000

971 000

530 000

750 000

880 000

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

8.8 24,5 36 52 49 87 83 135 205 310 290 430 580 760 730 1110 1070 1540 1490 2050 2000 2680 2500 3430 3200

10.9 36 53 76 72 125 122 200 300 440 420 620 820 1090 1040 1580 1500 2190 2120 2920 2800 3820 3500 4890 4600

12.9 43 62 89 84 150 145 235 360 520 490 720 960 1270 1220 1850 1800 2560 2480 3420 3300 4470 4100 5720 5300

Wrench size, (x) = according to DIN931, for Socket head Hex head screw screw mm Inch mm Inch 13

1/2

11/16

5/16

11/16

5/16

3/4

7/8

9/16

1-1/16

9/16

1-1/16

9/16

1-3/16

1-7/16

3/4

1-7/16

3/4

1-5/8

3/4

1-5/8

3/4

1-13/16

7/8

1-13/16

7/8

2-3/16

1-1/16

2-3/16

1-1/16

2-3/8

1-1/16

2-3/8

1-1/16

MJFCIFSS!

1.3.001 - 3 / 4

General

Service Manual

Tightening torques

Tightening torque for screws to mount SAE flange (not part of factory standard WN 4037 I) Listing according to LFR Quality service 2QA 6 051 00 as of Oct. 2001

3.1

Flanges and half flanges for high pressure (Norm 62)

Flange nominal size

Screw size

½" ¾" 1" 1 ¼" 1 ½" 2"

M8 M 10 M 12 M 14 M 16 M 20

3.2

3.3

31 62 108 172 264 350

-45 70 120 170 250

-65 110 180 250 450

Half flange for low pressure (Norm 61)

Flange nominal size ½" ¾" 1" 1 ¼" 1 ½" 2" 2 ½" 3" 3 ½" 4" 5"

Tightening torques in Nm for screw grade 10.9 Flat flange without Flange with Half flange reinforcement rim reinforcement rim

Tightening torques in Nm for Screw grade 8.8 Screw grade 10.9

Screw size M8 M 10 M 10 M 10 M 12 M 12 M 12 M 14 M 16 M 16 M 16

22 44 44 44 76 76 76 122 187 187 187

31 62 62 62 108 108 108 172 264 264 264

Tightening torque for oil drain plugs on travel gear (40 km/h) (not part of the factory standard WN 4037 I)

Plug Thread size M 26x1,5

Tightening torques in Nm 40+10

1.3.001 - 4 / 4

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

General Conversion charts

1.3.002 Conversion charts by

To obtain

0,039

To obtain Multiply inch

25,4

3,281

feet

0,305

1,093

yard

0,914

0,621

mile

1,609

cm²

0,155

sq. inch

6,452

cm²

m²

10,764

sq. feet

0,093

m²

1,196

sq. yard

0,8361

m²

km²

0,386

sq. mile

2,59

km²

cm³

0,061

cu. inch

16,387

cm³

m³

35,314

cu. feet

0,028

m³

1,308

cu. yard

0,764

m³

61,025

cu. inch

0,016

0,035

cu. feet

28,316

0,264

gallon

3,785

1,057

quart

0,946

0,035

oz.

28,349

2,204

lbs.

0,453

1,102

short t

0,907

0,225

lbs.

4,449

224,732

lbs.

0,0044

Torque

0,737

ft. lbs.

1,356

Power

1,342

0,745

0,736

1,358

0,986

1,014

Pressure

bar

14,5

PSI

0,069

bar

(hydraulic)

kpa

0,145

PSI

6,896

kpa

Ground pressure

kg/cm²

14,223

lbs. sq. inch

0,0703

kg/cm²

kg/m²

0,205

lbs. sq. ft.

4,878

kg/m²

g/cm³

0,036

lbs. cu. inch

27,78

g/cm³

kg/m³

0,062

lbs. cu. ft.

16,13

kg/m³

km/h

0,621

mph

1,609

km/h

m/min

3,281

ft. / min

0,305

m/min

°C

(°Cx1,8) + 32

°F

(°F-32)/1,8

°C

°C+273

°K

°K-273

°C

Unit of measure

Multiply

Length

Area

Volume

Weight

Force

Compression Speed Temperature

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

1.3.002 - 1 / 2

Service Manual

General Tapping holes

1.3.003 Tapping holes 1

Tapping holes for metric ISO standard threads Thread size M1 M 1,1 M 1,2 M 1,4 M 1,6 M 1,7 M 1,8 M2 M 2,2 M 2,3 M 2,5 M 2,6 M3 M 3,5 M4 M 4,5 M5 M6 M7 M8 M9 M 10 M 11 M 12 M 14 M 16 M 18 M 20 M 22 M 24 M 27 M 30 M 33 M 36 M 39 M 42 M 45 M 48 M 52 M 56 M 60 M 64 M 68

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Thread size Ø Diameter limits max. min. 0,785 0,729 0,885 0,829 0,985 0,929 1,160 1,075 1,321 1,221 1,346 1,258 1,521 1,421 1,679 1,567 1,838 1,713 1,920 1,795 2,138 2,013 2,176 2,036 2,599 2,459 3,010 2,850 3,422 3,242 3,878 3,688 4,334 4,134 5,153 4,917 6,153 5,917 6,912 6,647 7,912 7,647 8,676 8,376 9,676 9,376 10,441 10,106 12,210 11,835 14,210 13,835 15,744 15,294 17,744 17,294 19,744 19,294 21,252 20,752 24,252 23,752 26,771 26,211 29,771 29,211 32,270 31,650 35,270 34,670 37,799 39,129 40,799 40,129 43,297 42,587 47,297 46,587 50,796 50,046 54,796 54,046 58,305 57,505 62,305 61,505

Drill bit Ø 0,75 0,85 0,95 1,1 1,25 1,30 1,45 1,6 1,75 1,9 2,05 2,10 2,5 2,9 3,3 3,7 4,2 5 6 6,8 7,8 8,5 9,6 10,2 12 14 15,5 17,5 19,5 21 24 26,5 29,5 32 35 37,5 40,5 43,0 47,0 50,5 54,1 57,6 61,6

MJFCIFSS!

1.3.003 - 1 / 2

General

Service Manual

Tapping holes

2 Thread size M 1 x 0,2 M 1,1 x 0,2 M 1,2 x 0,2 M 1,4 x 0,2 M 1,4 x 0,25 M 1,6 x 0,2 M 1,8 x 0,2 M 2 x 0,25 M 2,2 x 0,25 M 2,5 x 0,35 M 3 x 0,35 M 3,5 x 0,35 M 4 x 0,5 M 4,5 x 0,5 M 5 x 0,5 M 5,5 x 0,5 M 6 x 0,75 M 7 x 0,75 M 8 x 0,75 M8x1 M 9 x 0,75 M9x1 M 10 x 0,75 M 10 x 1 M 10 x 1,25 M 11 x 0,75 M 11 x 1 M 12 x 1 M 12 x 1,25 M 12 x 1,5 M 14 x 1 M 14 x 1,25 M 14 x 1,5 M 15 x 1 M 15 x 1,5 M 16 x 1 M 16 x 1,5 M 17 x 1 M 17 x 1,5 M 18 x 1 M 18 x 1,5 M 18 x 2 M 20 x 1 M 20 x 1,5 M 20 x 2 M 22 x 1 M 22 x 1,5 M 22 x 2 M 24 x 1 M 24 x 1,5

Tapping holes for metric ISO fine threads Hole Ø Diameter limits max. min. 0,821 0,783 0,921 0,833 1,021 0,983 1,221 1,183 1,185 1,129 1,421 1,383 1,621 1,583 1,785 1,729 1,985 1,929 2,201 1,121 2,721 2,621 3,221 3,121 3,599 3,459 4,099 3,959 4,599 4,459 5,099 4,959 5,378 5,188 6,378 6,188 7,378 7,188 7,153 6,917 8,378 8,188 8,153 7,917 9,378 9,188 9,153 8,917 8,912 8,647 10,378 10,188 10,153 9,917 11,153 10,917 10,912 10,647 10,676 10,376 13,153 12,917 12,912 112,647 12,676 12,376 14,153 13,917 13,676 13,376 15,153 14,917 14,676 14,376 16,153 15,917 15,676 15,376 17,153 16,917 16,676 16,376 16,210 15,835 19,153 18,917 18,676 18,376 18,210 17,835 21,153 20,917 20,676 20,376 20,210 19,835 23,153 22,917 22,676 22,376

Drill bit Ø

Thread size

0,8 0,9 1 1,2 1,15 1,4 1,6 1,75 1,95 2,15 2,65 3,15 3,5 4 4,5 5 5,2 6,2 7,2 7 8,2 8 9,2 9 8,8 10,2 10 11,1 10,8 10,5 13 12,8 12,5 14 13,5 15 14,5 16 15,5 17 16,5 16 19 18,5 18 21 20,5 20 23 22,5

M 24 x 2 M 25 x 1 M 25 x 1,5 M 25 x 2 M 26 x 1,5 M 27 x 1 M 27 x 1,5 M 27 x 2 M 28 x 1 M 28 x 1,5 M 28 x 2 M 30 x 1 M 30 x 1,5 M 30 x 2 M 30 x 3 M 32 x 1,5 M 32 x 2 M 33 x 1,5 M 33 x 2 M 33 x 3 M 35 x 1,5 M 36 x 1,5 M 36 x 2 M 36 x 3 M 38 x 1,5 M 39 x 1,5 M 39 x 2 M 39 x 3 M 40 x 1,5 M 40 x 2 M 40 x 3 M 42 x 1,5 M 42 x 2 M 42 x 3 M 42 x 4 M 45 x 1,5 M 43 x 2 M 45 x 3 M 45 x 4 M 48 x 1,5 M 48 x 2 M 48 x 3 M 48 x 4 M 50 x 1,5 M 50 x 2 M 50 x 3 M 52 x 1,5 M 52 x 2 M 52 x 3 M 52 x 4

1.3.003 - 2 / 2

Mjfcifss!

Hole Ø Diameter limits max. min. 22,210 21,835 24,153 23,917 23,676 23,376 23,210 22,835 24,676 24,376 26,153 25,917 25,676 25,376 25,210 24,835 27,153 26,917 26,676 26,376 26,210 25,835 29,153 28,917 28,676 28,376 28,210 27,835 27,252 26,752 30,676 30,376 30,210 29,835 31,676 31,376 31,210 30,835 30,252 29,752 33,676 33,376 34,676 34,376 34,210 33,835 33,252 32,752 36,676 36,376 37,676 37,376 37,210 36,835 36,252 35,752 38,676 38,376 38,210 37,835 37,252 36,752 40,676 40,376 40,210 39,835 39,252 38,752 38,270 37,670 43,676 43,376 43,210 42,835 42,252 41,752 41,270 40,670 46,676 46,376 46,210 45,835 45,252 44,752 44,270 43,670 48,676 48,376 48,210 47,835 47,252 46,752 50,676 50,376 50,210 49,835 49,252 48,752 48,270 47,670

TL 435-10 TL 445-10 TL 435-13 TL 442-13

Drill bit Ø 22 24 23,5 23 24,5 26 25,5 25 27 26,5 26 29 28,5 28 27 30,5 30 31,5 31 30 33,5 34,5 34 33 36,5 37,5 37 36 38,5 38 37 40,5 40 39 38 43,5 43 42 41 46,5 46 45 44 48,5 48 47 50,5 50 49 48

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

General Conservation guidelines

1.4.000 Conservation guidelines 1

General All parts of a construction machine are exposed to corrosion, especially when the machine is taken out of service. Corrosion can be compared to wear. However, the effects of corrosion can greatly exceed that of mechanical wear and shorten the service life of the affected parts significantly. For that reason, for longer shut down, the machines and its components must be preserved according to certain guidelines. In general, these guidelines are tiered according to the following times: Taking the machine out of service â&#x20AC;&#x201C; for an unknown duration Shut down of the machine Shut down for up to 2 months Shut down for up to 12 months Shut down for longer than 12 months Return to operation The required measures are graduated depending on the different time frames. The conservation measures cannot be strictly standardized and they must be shorted or lengthened depending on the assessment of necessity (such as environmental influences). Such influences are, for example: Placement location of machine (for example in unprotected surrounding, in closed areas, protected by a roof, temperate surrounding) Type of climate (for example extreme temperatures, location in water / near the coast, etc.) Note! For conservation for sea transport, special guidelines must be observed, which are not included in these instructions. Refer to the special operating instructions.

Taking the machine out of service â&#x20AC;&#x201C; for an unknown duration If a machine is taken out of service for a longer period of time without conservation, then it must be operated in intervals not to exceed 14 days, to prevent abnormal corrosion and its effects. Before putting the machine back into service, check all oil levels and correct them, if necessary. Always carry out the specified daily maintenance work before putting the machine back into service. In addition, carry out the time limited maintenance work according to the inspection schedule and additional Diesel engine Operating instructions no later than the specified intervals. Put the machine into operation according to the Operating instructions and operate it until the Diesel engine and the hydraulic system has reached the specified operating temperature in the hydraulic tank and in the coolant circuit. Actuate all functions of the travel, working hydraulic as well as functions of additionally installed hydraulic components and alternately operate them over a period of approx. 20 minutes. The hydraulic cylinders must be extended and retracted over their full stroke length. When turning the machine off, retract all hydraulic cylinders fully, if possible, and fill the fuel tank. If the machine is parked on soft ground, park the machine on wooden planks or similar and secure it to prevent it from rolling off. Check the batteries and remove them and recharge them, if necessary. Check the electrical contact points and grease them, if necessary.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

1.4.000 - 1 / 6

General

Service Manual

Conservation guidelines

Shut down of the machine Preparations for shut down Park the machine on horizontal, dry and solid ground and secure it to prevent it from rolling off. Lower the working attachment to the ground level so that there is no longer any residual pressure of the hydraulic. Clean the machine diligently according to the procedure outlined in the Operating instructions. The machine must be completely dry before starting the conservation measures. Dry electronic components and damp areas on the machine with pressurized air. If freezing temperatures are expected for the intended duration of shut down, then the fuel tank must be filled with winter fuel. Then start the Diesel engine and let it run for some time to bring the winter fuel into the fuel circuit. Then add enough fuel to the fuel tank until it is full. Note! When a conserved machine is moved for loading or transport, then the conservation protection on the piston rods of the cylinders will most often be removed by the scraper ring. For that reason, if the machine is transported, the conservation of the piston rods must be rechecked after loading and carried out again, if necessary. Note! Despite completed conservations measures, the machine must still be inspected in certain intervals and touched up, if necessary. This is within left to the discretion of the operator, but these inspections should be carried out regularly (monthly), especially in aggravated conditions (cold, heat, near the coast, etc.).

3.1

Shut down for up to 2 months Required tools / Service items Description Optical charge tester

Id. No. See section 2.1

Description To check the battery condition and the antifreeze in the coolant

WAXOYL 120-4 Anti corrosion wax

8504472

Ballistol Spray Corrosion protection Dehumidification capsule

10025514

Spray can 500ml Long term protection for up to 2 years Application area: Door locks Prevents infiltration of moisture over an extended period of time

10013313

Display

Check the entire machine for damage and remedy, if necessary. Check the machine for paint damage and remedy, if necessary. Take care of any maintenance work which would fall within the timeframe of the planned shut down. Due to the UV exposure of the components, synthetic materials, such as plastic parts, hoses, rubber etc. must be covered with suitable aids. Electrical components, contact points and plug connections which are not sealed must be sealed with conservation wax â&#x20AC;&#x17E;Waxoyl 120-4â&#x20AC;&#x153;.

1.4.000 - 2 / 6

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

General Conservation guidelines

Apply a thick layer of conservation wax „Waxoyl 120-4“ to cover ball joints, hinges, blank parts and exposed piston rods. (Do not protect ball bearings with Waxoyl!) Place a dehumidification capsule into the central electric box. Protect all door and container locks with „Ballistol Spray“. Set the battery master switch (if present) to position „0“ and then remove the batteries. Check the battery acid level and add distilled water, if necessary. Always store the batteries in a cool and dry area. Check the load current regularly every 6 weeks and recharge, if necessary. Close the exhaust outlet with an air and watertight cover. Pay attention to any additional guidelines for special components or special local conditions.

3.2

Shut down for up to 12 months Carry out all measures according to paragraph 3.1. In addition, the following is required: Clean the Diesel engine externally. Drain water from the fuel tank or condensation of the Diesel engine prefilter (see Operating instructions). Add commercially available Diesel fuel to the fuel tank until it is completely full. If the shut down is during the cold time of the year, fill the fuel dank with winter Diesel fuel (Winter Diesel fuel is suitable up to a temperature of -22°C / -7.6°F). Then start the Diesel engine and let it run for some time to bring the winter fuel into the fuel circuit. Then add enough fuel to the fuel tank until it is full. Check the coolant to ensure it has sufficient corrosion and antifreeze protection - at least 50% corrosion inhibitor antifreeze fluid (for guidelines refer to the Operating instructions). Seal the entire machine (Diesel engine, hydraulic aggregates, main frame, tank, travel gear / axles, equalizer bar, working attachments, etc.) with preservation wax „Waxoyl 120-4“. (Amount of preservative agent: An area of approx. 5m² can be treated with one liter Waxoyl) Note! The following points must be observed when applying the corrosion inhibitor wax: Observe a drying time of 3 hours. Ambient temperature at least +15°C / 59°F. Use protective equipment (breathing protection, safety glasses, respirator, etc.). The solvents of the anti corrosion wax are flammable! (Do not smoke and avoid open flames!) Cold resistant to a temperature of -40°C / -40°F. Release the chain tension by relieving the tension cylinder (see Operating instructions). Check the machine monthly and reapply conservation protective measures if necessary.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

1.4.000 - 3 / 6

General

Service Manual

Conservation guidelines

3.3

Shut down for longer than 12 months Carry out all measures according to paragraph 3.1 and 3.2. In addition, the following is required: Note! If a shut down for longer than 12 months is scheduled, then contact the Service Dept. of the Diesel engine manufacturer. Close off all openings, such as air filter, exhaust pipe, vent openings on components, etc. airtight. The vent for the fuel tank (if present) must remain open for safety reasons! Rub the rubber seal of the cab and containers with talcum powder, close the doors. If the cab is not installed, cover the operator’s platform properly. If necessary, remove the operator’s seat. Cover the instrument panel and protect it.

4 4.1

Return to operation After a shut down of 2 months Remove the dehumidification capsule from the electronic box. Check the fill levels and lubricate the machine according to the Operating instructions. Install the batteries and clean / grease the battery terminals. Open the exhaust outlet. Drain water from the fuel tank or drain any condensation of the Diesel engine prefilter (see Operating instructions). Clean anti corrosion wax from ball joints, hinges, blank parts and exposed piston rods. Put the machine back into service as outlined in the Operating instructions. Before working with the machine, check all functions of the machine and remedy and defects immediately. Carry out a thorough visual inspection on the machine. Actuate all functions of the travel, working hydraulic as well as functions of additionally installed hydraulic components and alternately operate them over a period of approx. 20 minutes. The hydraulic cylinders must be extended and retracted over their full stroke length. Observe any additional guidelines for special components or special local conditions.

4.2

After a shut down of 12 months Carry out the items according to paragraph 4.1. Take an oil sample of the hydraulic oil and send it in for analysis. Carry out the scheduled maintenance and inspection work on the machine before putting it back into service. On the Diesel engine, mechanically actuate the AGR flap (exhaust return) and the engine brake flap and check for easy movement. Grease the V-belts! Use a high pressure cleaner with steam (at least 120°C) as well as 5% additive of solvent (such as petroleum) to clean the anti corrosion wax from the machine and aggregates. (Caution when walking on surfaces, there is a danger of slipping due to the wax residue.) Check the V-belt of the Diesel engine and replace it if necessary. Carry out a Diesel engine test run: Increase the Diesel engine rpm only slowly to ¾ of the high idle rpm until the operating temperature is reached. Check the oil pressure display immediately after starting the Diesel engine. Check the vacuum display of the air filter. Adjust the chain tension to suit the application (see Operating instructions).

1.4.000 - 4 / 6

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

General Conservation guidelines

4.3

After shut down of longer than 12 months Complete all items outlined in paragraph 4.2 and 4.1. Note! After a scheduled shut down of longer than 12 months contact the Service Dept. of the Diesel engine manufacturer. Remove all covers and closures, which were installed for conservation measures. Turn the Diesel engine manually a few turns (use the turning device - flywheel â&#x20AC;&#x201C; see Special tools). Start the machine and bring it to operating temperature. After the machine was brought to operating temperature, change all lube and service fluids as well as filters according to the Operating instructions Check the entire machine for function and for leaks. If necessary, carry out any time limited maintenance work at this time.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

1.4.000 - 5 / 6

Service Manual

General Material weights

1.5.000 Material weights Material Anthracite coal

spec. weight1) kg/m3 fest 1600 590 - 890 2970 1900 1280 2200 1900 2020 1540 3170 2790 2730 2130 - 2900 2610 2170 1690 1900 2260 860 2020 1840 2080 1660 1840 3260 1370 2670 3030 1600 1900 2080 2020 1930 2230 2520 1660 2940 2610

Loosening in % 35 35 8 52 33 35 35 35 26 26 23 75 75 64 18 69 12 12 12 12 54 22 24 24 17 19 17 44 67 18 12 12 13 26 12 10 67 33 68 49

Loosening factor 0,74 0,74 0,93 0,66 0,75 0,74 0,74 0,74 0,79 0,79 0,81 0,57 0,57 0,61 0,85 0,59 0,89 0,89 0,89 0,89 0,65 0,82 0,80 0,80 0,86 0,84 0,86 0,69 0,60 0,85 0,89 0,89 0,88 0,79 0,89 0,91 0,60 0,75 0,59 0,67

spec. weight kg/m3 loose 1190 1100 550 - 830 1960 1420 950 830 1630 1510 1600 1250 1810 1660 1660 1810 - 2450 1540 1540 1930 1510 1690 2020 1560 1660 1480 1660 1420 2540 2790 950 1600 2580 1420 1690 1840 1600 2400 1720 2020 1510 1250 1750 130 520 1750

- raw - washed Ash bituminous coal Basalt Bauxite, Kaolin Bituminous coal - raw - washed Carnotite, Uranium ore Soil - dry hardened - wet loosened - clay Gypsum - broken - ground Granite - broken Hematite, iron ore Limestone - broken - ground Gravel - damp - dry - dry 6-50mm - wet 6-50mm Coke Loam, clay - seasoned - dry - wet Clay with gravel - dry - wet Magnetite, iron ore Topsoil Natural stone - ground Pyrite, iron ore Sand - dry, lose - damp - wet Sand with clay - lose - compressed Sand with gravel - dry - wet Sandstone Slate Slag - broken Snow - dry Sand with clay - lose Trapp rock - broken Weathered rock 2790 42 0,70 1960 75% rock, 25% soil Weathered rock 2280 33 0,75 1720 50% rock, 50% Soil Weathered rock 1960 24 0,80 1570 25% rock, 75% Soil 1) The actual values depend on the moisture content, the grain size and the compression. Testing is required to determine more exact values.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

1.5.000 - 1 / 2

Service Manual

Tools and work instructions Sub group index – Tools and work instructions

2 Tools and work instructions 2.0.000 Sub group index – Tools and work instructions Special tools .................................................................................................. 2.1 Repair welding ............................................................................................... 2.2 Assembly instructions .................................................................................. 2.3

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

2.0.000 - 1 / 2

Service Manual

Tools and work instructions Special tools

2.1.000 Special tools General The following section is divided into three sections: 1 Special tools - Maintenance 2 Special tools - Repairs 3 Special tools for in-house manufacture Special tools for maintenance are a must-have to carry out the maintenance and inspection schedule. In addition, some tools are necessary aids for troubleshooting. Special tools for repairs are only required in case of a repair of the affected components. Special tools for in-house manufacture can be made in-house as necessary. The drawings to make them are made available by the manufacturer.

1 1.1

Special tools Maintenance Diesel engine

Description

Id. No.

Remarks

Turning device for flywheel JDE83

7090362

To adjust the valve clearance, install on the flywheel housing

Adjustment pin JDG1571

7090360

Is required together with JDE 83 to adjust the valve clearance.

Illustration

To hold the flywheel TDC to adjust the injection pump. Digital rpm gauge „Shimpo“

Reflective tape

7364 284

6140 632 01

To measure the rpm with reflective tape Test range: 6-8300 rpm Accuracy: 1 rpm Use with Shimpo rpm gauge

Optical charge tester

7408922

To check the battery charge condition and the antifreeze in the coolant

V-belt test unit „Krikit2“

8042829

To check the V-belt tension

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

2.1.000 - 1 / 14

Tools and work instructions

Service Manual

Special tools

1.2

Hydraulic system

Description Vacuum pump 12V cpl. with accessories Consisting of:

Id. No.

Illustration

10355585

For faster bleeding of hydraulic system, by enclosing the PVC hose, a slight excess pressure can be produced.

10024185

Accuracy:

Vacuum pump with electrical cable, PVC hose inside diameter 5mm, Fitting

Temperature gauge

Remarks

2%/2°

Test range: -18°C - +260°C

Difference pressure test set 230V Consisting of:

7025 376

Test unit Multi-Handy 2045 2 pressure sensors 0-600 bar 2 Mini test connections 2 test cables 12m long KFZ connector cable Data cable Power unit

Accuracy: 1% of the scale end value

Scale pressure gauge 0-10 0-25 0-40 0-60 0-100 0-160 0-250 0-400 0-600 0-1000

To measure pressure, pressure peaks and pressure difference and suitable for data transfer to PC

5002 865 7361 289 7361 288 5002 867 5602 903 7361 286 7361 285 7500 002 7361 294 4601 115

All pressure gauges are glycerin filled

2.1.000 - 2 / 14

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

Tools and work instructions Special tools

Description Pressure gauge connection R½

Id. No. 7002 436

Test fitting, cpl. R6L R 10 L R 12 L

7409 916 7406 864 7409 918

To seal at pressure tests, a square seal ring, Id.No. 7409 794 must be used.

Union nut and compression ring are affixed on the test fitting.

7615 321 5608 462 7407 071 7406 865 7409 720

Screw coupling M 16x2

7407 070

Test hose NW 2 1000 mm 1500 mm 4000 mm 5000 mm

7002437 7002475 7009134 7363732

Hook wrench 45 50 mm 58 62 mm

TL 435-10 TL 445-10 TL 435-13 TL 442-13

Illustration

To connect to additional test points in the machines

Screw coupling M 8x1 M 10x1 M 12x1.5 M 14x1.5 R¼

Remarks

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

7403366 7900282

To connect shorter test lines or for connection between test connection and pressure sensor

To keep loss of pressure during tests to a minimum, shorter test hoses are preferable

To loosen / counter when adjusting the pump regulating range Use with socket wrench HPV

MJFCIFSS!

2.1.000 - 3 / 14

Tools and work instructions

Service Manual

Special tools

Description

Id. No.

Remarks

Socket wrench for grooved nut HPV

9792711

To loosen / counter when adjusting the pump end stop

Illustration

Use with hook wrench Groove ø 45.5 +0.5mm

Socket wrench for 0position grooved nut HPV

9749025

To loosen / counter when adjusting the hydraulic zero position Groove ø 32 +0.5 mm

Angle screwdriver Size 22

8000989

To close off high pressure connections

Test plates For SAE flange 1/2 A 90mm B 32mm C, r 5mm For SAE flange 3/4 A 90mm B 40mm C,r 5mm For SAE flange 1 A 90mm B 44mm C,r 5mm

For cap hydraulic tank

10355369 Material: Ground spring steel 7370092

Round off end of the plate (simplifies installation, avoids damage to the seal ring)

7370093

Or to be made in-house

2.1.000 - 4 / 14

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

Tools and work instructions Special tools

1.3

Electrical system

Description

Id. No.

LinDiag Diagnostics Consisting of:

Remarks

Illustration

To adjust the travel hydraulic, read out the Service Codes and for troubleshooting on machines in exhaust stage Tier2 and Tier3

Data carrier with latest software version Dongle for LinDiag 7 9124.01.750 Adapter cable for LH-ECU-UP/CR

10467309

USB - Adapter

693190714

Intermediate adapter from serial to USB Is only required for notebooks without serial connection

Bodem Software with copy protection plug for USB connection

10285174

To adjust the working hydraulic, read out the Service Codes and for troubleshooting on machines

Bodem Data cable

6905910

To adjust the working hydraulic

Flash tool Working hydraulic controller (is not required for adjustments

10412388

To transfer updates to the working hydraulic control

Digital multi meter cpl. with cable and bag

10018500

for

10297212 10035410

Voltage (V)Amperage (A)Resistance ( )and Frequency (Hz)tests

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

2.1.000 - 5 / 14

Tools and work instructions

Service Manual

Special tools

Description

Id. No.

Optical charge tester

LMB Magnet

see Pt. 1.1 Diesel engine 10354217

Remarks

Illustration

To check the battery condition and the antifreeze in the coolant For calibration mode of electronic load display Already included on tool box.

1.4

Mechanical component groups

Description

Id. No.

Remarks

Feeler gauge

8145535

To measure the wear on the brake disks (service brake))

2 2.1

Illustration

Special tools - Repair Diesel engine Note! The special tools for Diesel engine repair are listed in the Diesel engine workshop manual.

2.1.000 - 6 / 14

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

Tools and work instructions Special tools

2.2

Hydraulic system

Description

Id. No.

Socket wrench Valve sleeve

10430260

Remarks

Illustration

For repair of variable motor HMV To remove and install the valve sleeve of the directional valve See section 10.2 Position 73

Mandrel thrust ring

For repair of var. pump HPV or var. motor HMV

HPV 75

10472251

HMV 210

10472261

For the installation of the hot thrust ring on the drive shaft. See chapter 10.1 or 8.2. Position 11

For repair of var. pump HPV or var. motor HMV

Mandrel [1] and protective sleeve [2] for shaft seal ring HPV 75

10472271

HPV 75

10472273

HMV 210

10472317

HMV 210

10410295

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

For pressing in the radial shaft seal ring to push over the drive shaft (in connection with the corresponding protective sleeve) See section 10.1 or 10.2 Position 12

MJFCIFSS!

2.1.000 - 7 / 14

Tools and work instructions

Service Manual

Special tools

Description

Id. No.

Remarks

Illustration

For repair of var. pump HPV or var. motor HMV

Installation aid for seal ring on oil guide pipes Pos.1 HMV 210

10472322

The tool is used to install the O-rings on the oil guide pipes

Pos.2 HPV 75

10472321

See Section 10.1 Position 46 or section 10.2. Position 45

Spindle device for swash plate mount

10324938

For repair of var. pump HPV or var. motor HMV With this device, the swash plate mount can be lowered targeted onto the pump housing at installation.

Centering pins for swash plate mount

For repair of var. pump HPV or var. motor HMV

M12

HPV 75

10324939

M14

HMV 210

10472320

The guide pins are used to guide the swash plate mount at assembly with the pump housing. minimum 2 each maximum 4 each required

2.1.000 - 8 / 14

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

Tools and work instructions Special tools

Description

Id. No.

Centering device for swash plate mount

10324937

Remarks

Illustration

For repair of var. pump HPV or var. motor HMV Device to affix the oil guide pipes at installation of swash plate mount 2 each required

Note! The special tools for cylinder repair are listed in the spare parts list.

2.3

Electrical system

Description

Id. No.

Crimper for MATE-N-LOK Crimp contacts

Remarks To make proper crimp connection on MATE-N-LOK plug connections

For 1,5 mm² For 2,5 mm²

7367025 7366314

Removal tool AMP for MATE-N-LOK Crimp contacts

7366655

Spare insert

7015180

Installation tool AMP for MATE-N-LOK Crimp contacts

8145432

To insert the pin and bushing contacts in MATE-N-LOK plug connectors

Hand Crimper for „Deutsch“ plug connector

8503647

To make proper crimp connections

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Illustration

To remove crimp contacts from plug connector

MJFCIFSS!

2.1.000 - 9 / 14

Tools and work instructions

Service Manual

Special tools

Description

Id. No.

8503633 8503632 10114733 885563714 10114732 To remove pin and bushing contacts in „Deutsch“ plug connectors (alternate)

Removal tool Cannon for Deutsch crimp contacts (alternate) AWG 12 AWG 16 AWG 20

8145674 8145673 8503630

Crimper AMP AMP Certi-Lock

7415333

Removal tool AMP AMP 726 503-1

Illustration

To remove pin and bushing contacts in „Deutsch“ plug connectors

Removal tool Cannon for „Deutsch“ crimp contacts AWG 4 AWG 8 AWG 12 AWG 16 AWG 20

Remarks

7026266

Crimper ESA 0760 CRB 0560

7409781 7409782

Insulating pliers, cpl. Type 5011-26

7409777

To crimp the „JUNIOR POWER TIMER“ contacts

To remove contacts from the „JUNIOR POWER TIMER“ housing

To crimp insulated 0.5 -6.0 mm² cable shoes, for example cable connectors CRB 0560 also windshield wiper motor

To insulate the 0.75 mm² electric cable

Spare cutter: 1.5-6.00 qmm 0.15-2.5 qmm

7409788 7409789

2.1.000 - 10 / 14

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

Tools and work instructions Special tools

Description

Id. No.

Removal tool METRI-PACK

Remarks

Illustration

To remove connector clamps on central plug of engine electronic ECU

wide narrow

7091022 7091023

2.4

Mechanical component group

Description

Id. No.

Remarks

Eyebolt

4000785

To install and remove the operatorÂ&#x2019;s cab to gain access to the hydraulic tank

Screw swirl

10490498

To install and remove the 1350kg ballast weight.

Illustration

2 each required See section 2.3 Installation instructions. Installation aid Ballast weight

see Pt. 3 Tools for in-house manufacture

To remove and install the 625kg ballast weight to equalize the center of gravity 2 each required See section 2.3 Installation instructions. This tool can also be used as an alternate for the screw swirl 10490498.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

2.1.000 - 11 / 14

Tools and work instructions

Service Manual

Special tools

2.5

Telescopic boom

Description

Id. No.

Remarks

Spacer for the telescopic cylinder (13m)

9410926

Device to keep two cylinders of the 13m telescope apart for repair

Eyebolt

9417658

To install and remove tilt cylinder

Open ended box wrench

8122204

The wrench is ground at the opening to be able to install hoses on the solenoid valves

Pin puller

10306272

To pull the two pins from the cylinder bearing Â&#x2013; telescopic cylinder 1 of 13 m telescope

Illustration

Or to be made in-house

External bleeding of telescopic cylinder Hydraulic hose

9412239

Flange half SAE 3/4Â&#x201C; Hex head screw M10x35 10.9 Hose fitting

10286359

(TL 4xx-13 F/N xxx6000 9500) 2 each required

4001246

4 each required

10815208

(TL 4xx-13 F/N xxx-9501 ) can also be carried out with the aid of the already installed hose by using the fitting

Pulling device

10306606

To replace the hose on the 13m telescopes from TL 4xx-13 F/N xxx9501

2.1.000 - 12 / 14

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

Tools and work instructions Special tools

Special tools for in-house manufacture Note! The following dimensions are given in millimeters [mm].

3.1

Pin puller To pull the two pins from the cylinder bearing Â&#x2013; telescopic cylinder 1 of the 13 m telescope. See also section 17.2 Repair instructions.

Fig. 1 Pin puller

1 2 3 4

Guide rod Hex fitting Impact sleeve Allen screw M8x30 8.8

5 Hex nut M20 6 Washer ISO 8738 20 7 2x Washer DIN 433 8,4

Note! Affix the hex nut Pos.5 with three weld points.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

2.1.000 - 13 / 14

Tools and work instructions

Service Manual

Special tools

3.2

Installation aid for ballast weight To remove and install the 625kg ballast weight. Is used to equalize the center of gravity, since it is not located in the center. The angle equalized the distance, so that the ballast weight can be installed / remove without jamming.

Fig. 2 Installation aid for ballast weight

2.1.000 - 14 / 14

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

Service Manual

Tools and work instructions Repair welding

2.2.000 Repair welding Caution! In principle, prior to beginning any welding work on the telescopic handler, disconnect the electronic boxes and various electronic components (see Operating instructions). In addition, the ground terminal of the welding unit must be connected directly to the blank work piece, which is to be welded.

Preparation of cracked part Clean the cracked area to remove paint, grease and any dirt. To prevent the crack from extending during the preparation and welding process, the end of the cracks should be drilled out with a drill (at least 8 mm Ø). Then the crack should be ground, chiseled, or arched out to an angle of approx. 60° . Be certain that the edges are clean and extend through the full cross section of the material, without exceeding the space of 1 mm in the lower part. On larger grooves, a welding safety should be installed.

Fig. 1-1 Ground out / drilled out crack

Certain materials must be preheated to approx. 150°C Special preparations are necessary when preparing a crack in manganese steel. This material cannot be prepared with a chisel or planing machine, due to its hardness and peen hardening. We suggest that the crack is prepared with a slow running and water-cooled grinding wheel to prevent overheating. Note! Another possibility to prepare cracks and remove high alloy welding seams is the use of cutting electrodes of the type UTP 82 AS.

Preparation of a weld The area to be welded must be fee of grease, paint, oil, moisture and dirt. During rain, the area to be welded must be covered sufficiently. Materials with a thickness above 15 mm and high carbon steel (carbon content more than 0.22 %) and difficult to weld steel, the material must be preheated to approx. 80°- 200°C. Preheating is also necessary when the component temperature at the start of the welding work is below +5°C and when the construction of the repair part prevents the welding stress to be released.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6600 F/N xxx-6600 F/N xxx-6600 F/N xxx-6600

MJFCIFSS!

2.2.000 - 1 / 6

Tools and work instructions

Service Manual

Repair welding

Treatment of electrodes Use only dry electrodes for welding. Electrodes with damaged coating and rusted electrodes may not be used any longer. Electrodes must be stored in a dry room with a minimum temperature of 15°C. Open electrode packages must be carefully closed and stored after the welding work is complete.

Welding technique The welding of material with the required electrodes (see chart under paragraph 7) is carried out according to DIN 1912. The adjustment of the welding current dictated by the different thicknesses of the electrodes can be taken from the chart of the electrode package. Beginning with material thickness of 8 mm, butt welds must be made in several layers. The weld is applied in several beads. Wide butt welds are filled with several side by side beads, with the last layer covering the center. The electrode should meld evenly without creating burrs and peaks. The valley or crater, which is created when changing electrodes must be filled in and overlapped with the next electrode. To prevent cracks in those craters, care must be taken that they are properly filled in. If the crack extends towards the outer edge of the material, slap may be trapped or burn holes may be created. To prevent this, the following aid may be used: tack apiece of sheet metal to the outer edge of the material. The welding seam begins now at the sheet metal in the direction of the arrow. After the welding is completed, the sheet metal is removed and the edge of the material is ground smooth. The welding seam must be cooled off slowly and should therefore be protected from rain and wind.

Fig. 4-1 Crack running to the outer edge of the material / Prepared crack

2.2.000 - 2 / 6

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6600 F/N xxx-6600 F/N xxx-6600 F/N xxx-6600

Service Manual

Tools and work instructions Repair welding

Reinforcement of welding seam If the crack of the material is due to on overload or abuse, a reinforcement plate should be welded over the crack. The selection of the correct reinforcement plate is based on the construction and load factors of the component to be repaired. For that reason, only general recommendations can be made as to the size and shape of the reinforcement plates.

5.1

Shape of plate The crossover or connection between the reinforced and not reinforced part should be as gradual as possible, this means that the size of the plate should be selected in such a way that new or unacceptable high stress in the repaired part is avoided. Plates with sharp corners (such as a rectangular plate) may not be used.

Fig. 5-1 Reinforcement plate against clean pulling / bending and alternating loads

5.2

Plate thickness The thickness of the reinforcement plate should be up to 2/3 of the thickness of the material to be reinforced.

5.3

Material quality of the plate The material properties (yield and tensile strength, etc.) of the reinforcement plate should be equal to the material to be reinforced.

5.4

Installation of the reinforcement plate The welded area of the crack should be ground so it is smooth and level. The size of the plate must be selected in such a way that the longer sides of the plate extend into the connecting construction of the material to be reinforced. The plate should also overlap the crack on each side by at least 20 mm. The correct position and fit of the reinforcement plate is achieved by clamping and spot welding.

5.5

Welding the reinforcement plate The reinforcement plate should be welded on by running a welding bead alternately on both sides. The welding should always start in the middle of the plate and run towards the outside. Be certain to observe that each welding seam has proper run out.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6600 F/N xxx-6600 F/N xxx-6600 F/N xxx-6600

MJFCIFSS!

2.2.000 - 3 / 6

Tools and work instructions

Service Manual

Repair welding

Welding direction

Fig. 5-2 Welding directions

The size of the welding run "a" is figured out in reference to the thickness "k" of the repair plate. Use formula: a=0.5 k Up to a welding run "a" of approx. 3 mm, a single run can be made, however, as a general rule, a double run should be preferred. Above a welding run "a" = 3 mm, the first run provides excellent penetration between the reinforcement plate and the basic material. Subsequent runs are added on top of the first run.

Fig. 5-3 3- or 1- layer welding seam

After the welding is completed, clean the welding seam as necessary and grind out the run between the reinforcement plate and the basic material.

Selection of correct welding electrodes For repair welding, only lime based (Kb) electrodes should be used, and as a rule, the electrodes (additional material) should be "softer" than the basic material. Exceptions to this ruse should be observed. Note! To reach the theoretical welding quality, the work must not only be performed in a professional manner, the electrode manufacturerÂ&#x2019;s guidelines must be strictly observed as well. Caution! Welding of vertical-down welds is not permitted for steel components!

2.2.000 - 4 / 6

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6600 F/N xxx-6600 F/N xxx-6600 F/N xxx-6600

Service Manual

Tools and work instructions Repair welding

6.1

Steel chart

Item

Description

Analysis

HARDOX 400

Weldable, low alloy special steel with high wear resistance, a tensile strength of 1250 N/mm² and a yield strength limit of 1000 N/mm²

C 0,27% Si 0,7% Mn 1,6% Cr 1,4% Mo 0,6%

Q St E 380 N

Fine grain structural steel poured at special low turbulence with a guaranteed minimum tensile strength of 500 - 640 N/mm² and minimum yield strength limit of 380 N/mm² Highly abrasion resistant steel with a tensile strength of 1720 N/mm²²

C 0,18% Si 0,5% Mn 1,6%

Special steel

St 52 - 3 S355J2G3 LH 690

6.2

Structural steel poured at low turbulence with a guaranteed minimum tensile strength of 510 N/mm² Tempered fine grade structural steel with a C 0,18% Si 0,50% tensile strength 770 - 940 N/mm² and a Mn 1,5% Mo 0,5 % yield strength limit of 690 N/mm² Ni 1,5 % Lightly alloyed with V, AI and Cu

Welding chart for arc welding

Item per EN 499: E42 5 B 4 2 H5 For example: Böhler FOX EV 50

per EN 757: E 69 6 Mn2NiCrMo B 4 2 H5 for example: Böhler FOX EV 85

per EN 1600: E 18 8 Mn B 2 2 For example: Böhler FOX A 7

TL 435-10 TL 445-10 TL 435-13 TL 442-13

C = 0,3% Mn = 0,7% Si = 0,5% Cu = 0,65% Mo = 0,3% V = 0,05% C 0,22%

F/N xxx-6600 F/N xxx-6600 F/N xxx-6600 F/N xxx-6600

Description E = Arc welding 42 = 500-640 N/mm² tensile strength 5 = Value for notch impact strength B = basic shielded 4 = Value for run out and type of current 2 = Value for welding positions H5 = maximum hydrogen content E = Arc welding 69 = 760-960 N/mm² tensile strength 6 = Value for notch impact strength Mn2NiCrMo = Chemical composition B = basic shielded 4 = Value for run out and type of current 2 = Value for welding positions H5 = maximum hydrogen content

E = Arc welding 18 = 620-770 N/mm² tensile strength 8 = Value for notch impact strength Mn = Chemical composition B = basic shielded 2 = Value for run out and type of current 2 = Value for welding positions

Analysis values in % / Application C = 0,07, Si = 0,5, Mn = 1,1 For connection and applied welds, especially for steels with low purity and higher carbon content. Weldable with DC current, Electrode on Plus terminal (+). No vertical seams. C = 0,05, Si = 0,4, Mn = 1,5, Cr = 0,4, Ni = 2,0, Mo = 0,5 For welds, which require high tenacity and crack resistance, use for highly alloyed fine grain steel. Very low hydrogen content in welding material. Weldable with DC current, Electrode on Plus terminal (+). No vertical seams. C = 0,1, Si = 0,7, Mn = 6,5, Cr = 18,8, Ni = 8,8 For connections between different alloyed and difficult to weld steel Weldable with DC current, Electrode on Plus terminal (+). No vertical seams

MJFCIFSS!

2.2.000 - 5 / 6

Tools and work instructions

Service Manual

Repair welding

6.3

Welding chart for metal inert gas weld with solid wire electrodes

Item per EN 440: G4Si1 For example: Böhler EMK 8

Per EN 12534: G3CrNi1Mo For example: Böhler X 70 - IG

per EN 12072: G 18 8 Mn For example: Böhler A7 IG

Description G = G = Metal inert gas weld with solid wire electrodes 4 = 500-640 N/mm² tensile strength Si = Chemical properties 1 = Value for run out and type of current

G = Metal inert gas weld with solid wire electrodes 3 = 900 N/mm² tensile strength CrNi1Mo = Chemical composition

G = Metal inert gas weld with solid wire electrodes 18 = 580-730 N/mm² tensile strength 8 = Value for notch impact strength Mn = Chemical composition

2.2.000 - 6 / 6

Mjfcifss!

Analysis values in % / Application C = 0,1, Si = 1,0, Mn = 1,7 For connection and applied welds, especially for steels with low purity and higher carbon content. Weldable with DC current, Electrode on Plus terminal (+). Shielding gas: Argon + 15-20% CO2 or 100% CO2 No vertical seams C = 0,1, Si = 0,6, Mn = 1,6, Cr = 0,25, Ni = 1,3, Mo = 0,25, V = 0,1 For welds, which require high tenacity and crack resistance, use for highly alloyed fine grain steel. Weldable with DC current, Electrode on Plus terminal (+). Shielding gas: Argon + 15-20% CO2 or 100% CO2 No vertical seams C = 0,08, Si = 0,9, Mn = 7,0, Cr = 19,2, Ni = 9,0 For connections between different alloyed and difficult to weld steel Weldable with DC current, Electrode on Plus terminal (+). Shielding gas: Argon + max. 2,5% CO2

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6600 F/N xxx-6600 F/N xxx-6600 F/N xxx-6600

Service Manual

Tools and work instructions Installation guidelines

2.3.000 Installation guidelines 1

General Described in this section are installation notes for various components, which must be observed at reinstallation in case of a repair.

2 2.1

Installation notes Equipment The threaded bores required to take on the 625 kg ballast weight are located outside the center of gravity of the weight. For that reason, the weight can get stuck at removal. To avoid this, the installation aids X (see section 2.1 Special tools) must be used. Because there is a risk of damage to the machine, the chains must be spread with the assistance of a suitable aid.

Fig. 2-1 Removal â&#x20AC;&#x201C; Ballast weight 625kg

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6600 F/N xxx-6600 F/N xxx-6600 F/N xxx-6600

MJFCIFSS!

2.3.000 - 1 / 4

Tools and work instructions

Service Manual

Installation guidelines

2.2

Travel hydraulic

1.1.1

Variable displacement pump Since the installation notes refer to the positions in the sectional drawing, they are described in section 10.1 „Variable displacement pump – Travel hydraulic“.

1.1.2

Variable displacement motor Since the installation notes refer to the positions in the sectional drawing, they are described in section 10.2 „Variable displacement motor – Travel hydraulic“.

1.1.3

Gear pump The double gear pump is accessible via the cover on the inside of the main frame. Raise the telescope and secure it with the aid of the hoist support. Remove the cover plate At installation of the fixed displacement pump – double gear pump, the following must be observed: Clean and grease the sealing surfaces on motor and pump. Seal the sealing surfaces with liquid seal.

Fig. 2-2 Double gear pump

In addition, it must be observed that the distance between flange and gear is at least 0.5 mm.

2.2.1

Collector block When removing or replacing the pressure filter, pay attention to the flow direction (marked on the filters) at installation. When removing or replacing the check valve (cold start valve) 57, pay attention to the opening direction at installation. The correct flow direction is marked on the valve.

2.3.000 - 2 / 4

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6600 F/N xxx-6600 F/N xxx-6600 F/N xxx-6600

Service Manual

Tools and work instructions Installation guidelines

Fig. 2-3 Installation of the pressure filter on the collector block

2.3

Working hydraulic

2.3.1

Telescope Since the installation notes refer to the positions in the sectional drawing, they are described in section 17.1 „Design and function“ or 17.2 „Repair instructions“.

2.3.2

Industrial control - Boom suspension Warning! Before starting any maintenance and repair work on the stabilizing module of the emergency down screw 252 (covered by a plug) back it out by 2-3 turns to relieve the pretension of the pressure accumulator 256 to the tank (connection T). Before putting it back into service, adhere the screw with Loctite.

Fig. 2-4 Pressure accumulator

The pretension of the pressure accumulator is reestablished when the telescope is raised.

2.4

Electrical system

2.4.1

DMS Sensor – rear axle See section 11.8 „DMS Sensor installation“.

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6600 F/N xxx-6600 F/N xxx-6600 F/N xxx-6600

MJFCIFSS!

2.3.000 - 3 / 4

Tools and work instructions

Service Manual

Installation guidelines

2.5

Main frame

2.5.1

Variable motor mount Observe the correct arrangement of the components at installation. Tighten the hex head screws 5 with a tightening torque of 350 Nm.

Fig. 2-5 Variable motor mount and installation of RPM sensor B2

Installation of RPM sensor Tighten the impulse sensor with 30Nm. Secure the sensor with Loctite to prevent it from twisting. With the aid of shims, adjust the distance between the RPM sensor B2 and the perforated plate 10.

2.5.2

Cab mount See section 16.1 „Operator’s cab“.

2.5.3

Stabilizers Secure the screws 24 at installation with Loctite.

Fig 2-6 Installation of stabilizers for 13m telescopic loader

2.3.000 - 4 / 4

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6600 F/N xxx-6600 F/N xxx-6600 F/N xxx-6600

Service Manual

Technical data and Maintenance guidelines Sub group index â&#x20AC;&#x201C; Technical data and Maintenance guidelines

3 Technical data and Maintenance guidelines 3.0.000 Sub group index â&#x20AC;&#x201C; Technical data and Maintenance guidelines Technical data................................................................................................ 3.1 Maintenance and inspection schedule ........................................................ 3.2 Maintenance and inspection guidelines...................................................... 3.3 Adjustment check list ................................................................................... 3.4 Inspection and adjustment tasks ................................................................. 3.5

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

MJFCIFSS!

3.0.000 - 1 / 2

Service Manual

Technical data and maintenance guidelines Technical data

3.1.000 Technical data TL43510

TL44510

TL43513

TL44213

Diesel engine Type Version Rating according to ISO 9249 Nominal RPM Low idle RPM

kW RPM RPM

High idle RPM RPM Displacement l Oil quantity incl. filter l Oil quality / viscosity Max. permissible machine incline all directions Firing order Coolant / DCA 80 L Fuel tank capacity l Fuel usage approx. l/h

D504 T 4 cyl. In-line, water cooled, turbocharged 80 (109 PS) 2400 1050 (with working hydraulic on) 850 (with working hydraulic off) 2450 4.5 12 See operating instructions 30° 1 3 4 2 See operating instructions 125 5 - 15

Splitterbox Type Version Ratio Oil quantity Oil quality / viscosity

4519.02 Spur gear 1-stage i 0,8974 l 1,7 See operating instructions

Hydraulic system Variable pumps Travel hydraulic Type Max. flow - Qmax l/min Operating pressure (M1 / M2) pmax bar Tandem gear pumps replenishing Cooling circuit / fan drive Size Max. flow replenishing - Qmax l/min Operating pressure (SP) pmax bar Max. flow - fan drive - Qmax l/min Operating pressure (electronically regulated) - pmax bar Gear motor fan drive Size Operating RPM RPM Variable motor Travel hydraulic Type Regulating pump Working hydraulic Max. flow - Qmax Stand-by pressure (HD) Operating pressure (HD) pmax

Type l/min bar bar

Hydraulic tank capacity Circuit, additionally Oil quality / viscosity

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

9500 9500 9500 9500

HPV75 - 02 203 420 28/ 11 65 20 26 180 8 presently 2000 / 2600 HMV 210 (25 km/h) A10V 045 120 35 300

l 95 l 95 See operating instructions

MJFCIFSS!

3.1.000 - 1 / 4

Technical data and maintenance guidelines

Service Manual

Technical data

TL43510

TL44510

TL43513

TL44213

Electrical system Operating voltage Batteries Alternator Starter Central fuse Individual fuses

V 12 Ah 170 12 V,65 A kW 4,2 A 125 See operating instructions Front axle

Front axle Planetary gear (axles) Axle ratio, total Oil quantity in axle casing - front axle Oil quantity in wheel head front axle Oil quality / viscosity and oil change intervals Service brake / parking brake front axle Tires

(45% Self locking differential) Type 212 / 415 / 709 i 1:6 1:26.25 See Operating instructions See Operating instructions See Operating instructions Type Disk brake See section 3.4

Rear axle Rear axle Planetary gear (axles) Axle ratio, total Oil quantity in axle casing rear axle Oil quantity in wheel head rear axle Oil quality / viscosity and oil change intervals Rear axle Tires

(0% Self locking differential) Type 212 / 416 / 710 i 1:6 1:26.25 See Operating instructions See Operating instructions See Operating instructions No brake See section 3.4

Steering Regulating pump Max. flow Steering / Servostat Steering cylinder Priority valve

Type l/min Type Type

A10V 045 120 LAGU 250/ 125 Synchronous cylinder LPS 160

Brake system Supply via regulating pump working pump

3.1.000 - 2 / 4

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

9500 9500 9500 9500

Service Manual

Technical data and maintenance guidelines Technical data

TL43510

TL44510

TL43513

TL44213

9129 9424 9477

9559 9839 9929

10565 10866 10913

General Travel speed Normal range III Reduced range II Reduced range I

km/h 0 km/h 0 km/h 0

Max. traction Depending on ground conditions

25 16 8

kN 56

Basic machine Overall height (without beacon) Overall length to front carrier Overall width via standard tires Height over rear Wheel base Rear overhang Track width Ground clearance (center of vehicle) Width over supported stabilizers Turning radius via tips of forklift prongs Turning radius via tires Operating weight Basic machine Basic machine with standard forklift Basic machine with standard bucket

mm mm mm mm mm mm mm mm mm mm mm

kg kg kg

2500 5810 2364 1710 2950 1130 1970 440 3150 5150 3850

8593 8857 8941

Standard forklift LH (various fork prongs) Fork prongs dimensions Max. prong distance Operating weight Load carrying capacity (depends on prongs) Standard bucket LH Bucket width Bucket capacity Operating weight Load capacity

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-6000 F/N xxx-6000 F/N xxx-6000 F/N xxx-6000

9500 9500 9500 9500

100x50 125x50 100x50 100x50 x1100 x1100 x1100 x1100 mm 955 955 955 955 kg 266 295 266 301 kg 3500 4500 3500 4200

mm m³ kg kg

2450 1 347 1800

MJFCIFSS!

3.1.000 - 3 / 4

Service Manual

Technical data and Maintenance guidelines Technical data

3.1.001 Technical data TL43510

TL44510

TL43513

TL44213

Diesel engine Type TL 4xx-xx F/N xxx-9501 10999 TL 4xx-xx F/N xxx-11000 Version Rating according to ISO 9249 kW Nominal RPM RPM Low idle RPM RPM High idle RPM RPM Displacement l Oil quantity incl. filter Oil quality / viscosity Max. permissible machine incline all directions Firing order Coolant / DCA 80 L Fuel tank capacity l Fuel usage approx. l/h

D 504 TI CD 4045 HF 287 4 cyl. In-line, water cooled, turbocharged 84 (114 PS) 2400 1050 2430 4,5 See operating instructions See operating instructions 30° 1 3 4 2 See operating instructions 125 5 - 15

Splitterbox Type Version Ratio Oil quantity Oil quality / viscosity

4519.02 Spur gear 1-stage i 0,8974 See operating instructions See operating instructions

Hydraulic system Variable pumps Travel hydraulic Type Max. flow - Qmax l/min Operating pressure (M1 / M2) pmax bar Tandem gear pumps replenishing Cooling circuit / fan drive Size Max. flow replenishing - Qmax l/min Operating pressure (SP) pmax bar Max. flow - fan drive - Qmax l/min Operating pressure (electronically regulated) - pmax bar Gear motor fan drive Size Operating RPM RPM Variable motor Travel hydraulic TL 20-25 km/h Type TL 40 km/h Type Regulating pump Working hydraulic Max. flow - Qmax Stand-by pressure (HD) Operating pressure (HD) pmax

Type l/min bar bar

Hydraulic tank capacity Circuit, additionally Oil quality / viscosity

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-9501 F/N xxx-9501 F/N xxx-9501 F/N xxx-9501

HPV75 - 02 203 420 28/ 11 65 20 26 180 8 2000 HMV 210 ICVD GT-S1N-233V-094 A10V 045 120 35 300

l 95 l 95 See operating instructions

MJFCIFSS!

3.1.001 - 1 / 4

Technical data and Maintenance guidelines

Service Manual

Technical data

TL43510

TL44510

TL43513

TL44213

Electrical system Operating voltage Batteries Alternator Starter Central fuse Individual fuses

V 12 Ah 170 12 V,75 A kW 4,2 A 125 A See operating instructions Front axle

Front axle (20-25 km/h) Front axle (40 km/h) Planetary gear (axles) Axle ratio, total (20-25 km/h) Axle ratio, total (40 km/h) Oil quantity in axle casing - front axle Oil quantity in wheel head front axle Oil quality / viscosity and oil change intervals Service brake / parking brake front axle Tires

(45% Self locking differential) 212 / 415 / 709 212 / 797 1:6 1:26,25 1:17,50 See Operating instructions See Operating instructions See Operating instructions Type Disk brake See section 3.4 Type Type i i i

Rear axle Rear axle (20-25 km/h) Rear axle (40 km/h) Planetary gear (axles) Axle ratio, total (20-25 km/h) Axle ratio, total (40 km/h) Oil quantity in axle casing - rear axle Oil quantity in wheel head rear axle Oil quality / viscosity and oil change intervals Service brake rear axle (20-25 km/h) Service brake rear axle (40 km/h) Tires

(0% Self locking differential) 212 / 416 / 710 212 / 798 1:6 1:26,25 1:17,50 See Operating instructions See Operating instructions See Operating instructions No brake Type Disk brake See section 3.4

Type Type i i i

Steering Regulating pump Max. flow Steering / Servostat Steering cylinder Priority valve

Type l/min Type Type

A10V 045 120 LAGU 250/ 125 Synchronous cylinder LPS 160

Brake system Supply via regulating pump working hydraulic

3.1.001 - 2 / 4

Mjfcifss!

TL 435-10 TL 445-10 TL 435-13 TL 442-13

F/N xxx-9501 F/N xxx-9501 F/N xxx-9501 F/N xxx-9501

Thank you very much for your reading. Please Click Here Then Get More Information.