AT-16 AUTOMATIC TRANSMISSION
-
AIR COOLED OIL COOLER
AIR COOLED OIL COOLER AT07I-05
COMPONENTS
Radiator Grille Sub-assy
Power Steering Oil Cooler Sub-assy
7.5 (76, 66 in.·lbf)
7.5 (76, 66 in.·lbf)
Clip
Oil Cooler Bracket 5.0 (51, 44 in.·lbf)
5.0 (51, 44 in.·lbf)
5.0 (51, 44 in.·lbf)
12 (122, 9)
12 (122, 9)
Oil Cooler Bracket
Clip
Oil Cooler Clip
Oil Cooler Pipe
Clip Clip
Oil Cooler Stay
5.0 (51, 44 in.·lbf) 5.0 (51, 44 in.·lbf)
12 (122, 9)
N·m (kgf·cm, ft·lbf) : Specified torque
D13117
2004 LAND CRUISER (RM1071U)
Author :
Date :
1870
AT-19 AUTOMATIC TRANSMISSION
-
AIR COOLED OIL COOLER AT07K-05
INSTALLATION Installation is in the reverse order of removal (See page AT-17 ). HINT: After installtion, check fluid level (See page AT-3-1 ).
Author :
Date :
1873
AT-17 AUTOMATIC TRANSMISSION
-
AIR COOLED OIL COOLER AT113-01
REMOVAL 1. (a) (b)
REMOVE RADIATOR GRILLE SUB-ASSY Remove the 3 screws. Release the 2 clips and remove the radiator grille subassy.
2.
SEPARATE POWER STEERING OIL COOLER SUBASSY Remove the 2 bolts and separate the power steering oil cooler sub-assy . Torque: 7.5 N·m (76 kgf·cm, 66 in.·lbf)
D12665
3. (a)
REMOVE OIL COOLER Loosen the 2 clips and disconnect the 2 hoses.
(b)
Remove the 4 bolts and oil cooler. Torque: 12 N·m (117 kgf·cm, 8 ft·lbf)
(c)
Remove the 8 bolts, the 2 oil cooler brackets and the 2 stays. Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)
D01688
D01689
D01690
2004 LAND CRUISER (RM1071U)
Author :
Date :
1871
AT-18 AUTOMATIC TRANSMISSION
-
AIR COOLED OIL COOLER
4. (a)
REMOVE OIL COOLER PIPE BRACKET Loosen the 2 clips and disconnect the 2 hoses.
(b)
Remove the 2 bolts and the oil cooler pipe bracket. Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf) Loosen the 2 clips and disconnect the 2 hoses.
D12666
(c)
D01692
2004 LAND CRUISER (RM1071U)
Author :
Date :
1872
AT-6 AUTOMATIC TRANSMISSION
-
ATF TEMPERATURE SENSOR
ATF TEMPERATURE SENSOR AT10Z-02
ON-VEHICLE REPAIR
Blue B
1. 2. 3. 4.
REMOVE ENGINE NO.2 UNDER COVER DRAIN ATF REMOVE OIL PAN (See page AT-1 1) REMOVE OIL STRAINER (See page AT-1 1)
5. (a) (b)
REMOVE ATF TEMPERATURE SENSOR Disconnect the 7 solenoid valve connectors. Remove the 2 bolts and disconnect the 2 ATF temperature sensors.
(c) (d) 6. (a) (b)
Disconnect the solenoid connector. Remove the bolt and the transmission wire harness. INSTALL ATF TEMPERATURE SENSOR Install the transmission wire harness. Install the bolt. Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf) Connect the solenoid connector.
A
Orange
D12704
(c) D12739
(d) (e)
Blue B
A
Orange
D12704
Connect the 7 solenoid valve connectors. Connect the 2 ATF temperature sensors with the 2 bolts. Torque: A: 11 N·m (112 kgf·cm, 8 ft·lbf) B: 10 N·m (100 kgf·cm, 7 ft·lbf) Bolt length: Bolt A: 36 mm (1.42 in.) Bolt B: 12 mm (0.47 in.) Sensor wire harness:
7. 8. 9. 10.
Wire harness
Color
for linear control
Orange
for oil temp warning lamp
Blue
INSTALL OIL STRAINER (See page AT-8 ) INSTALL OIL PAN (See page AT-8 ) FILL ATF AND CHECK ATF LEVEL (See page AT-3-1 ) INSTALL ENGINE NO.2 UNDER COVER
Author :
Date :
1860
AT-2 AUTOMATIC TRANSMISSION
-
AUTOMATIC TRANSMISSION SYSTEM AT07M-02
OPERATION Clutch No.3 (C3)
One-way Clutch No.1 (F1)
Clutch No.1 (C1) Clutch No.2 (C2)
One-way Clutch No.2 (F2)
Brake No.1 (B1) Brake No.2 (B2)
Brake No.3 (B3)
Brake No.4 (B4)
One-way Clutch No.3 (F3)
Shift Solenoid Valve SLU Shift Solenoid Valve SL2
Shift Solenoid Valve SLT
Shift Solenoid Valve SR
Shift Solenoid Valve S1
Shift Solenoid Valve SL1
Shift Solenoid Valve S2 D12728
2004 LAND CRUISER (RM1071U)
Author :
Date :
1853
AT-3 AUTOMATIC TRANSMISSION
Shift Lever Gear Position Position P R N
D
4
3 2 L
Park Reverse Neutral 1st 2nd 3rd 4th 5th 1st 2nd 3rd 4th 1st 2nd 3rd 1st 2nd 1st
S1
x x x
x x
S2
SR
SL1
x x x x
x x x x x x x
x x x x x x x
x x x x x x x x
x
x x x
x x
x x x
SL2
x
x x x x x x
C1
C2
C3
B1
B2
B3
B4
F1
F2
F3
x x x x x x
x x x
x x x x x x
x
x
x
x x x x x
x x x x
x
x x x
x x x x x x x x x x x x x x x x
x x x x x x x x x x x x x x x
x x
x x x x
x x x
x
x
x x x x
x x x
AUTOMATIC TRANSMISSION SYSTEM
SLU
x x x x
-
x x x x x x
x x x x x x x x x
x x
x x x x x
x x x x x x x x x
x
x
x
x x x
x x x x
x x
x x x
x
x x
x
x
x x x x x x x x x x
: Operating F1, F2, F3 : Operate only when driving
2004 LAND CRUISER (RM1071U)
Author :
Date :
1854
Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING
NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
AT-3-1 AUTOMATIC TRANSMISSION
-
AUTOMATIC TRANSMISSION SYSTEM
AUTOMATIC TRANSMISSION FLUID AT147-03
OPERATION 1.
Refill Plug
BEFORE TRANSMISSION FILL This transmission requires Toyota Genuine ATF WS. It is necessary to refill the transmission with the correct amount of fluid. The vehicle must remain level while adjusting the transmission fluid level. On vehicles equipped with active suspension, turn the suspension control switch OFF if it is necessary to jack up the vehicle with the engine running.
2. (a)
TRANSMISSION PAN FILL Remove the refill plug and overflow plug.
(b)
Fill the transmission through the refill hole until fluid begins to trickle out of the overflow tube. Reinstall the overflow plug.
Overflow Plug D13650
(c) Overflow Tube
D14352
2004 LAND CRUISER (RM1071U)
Author :
Date :
1855
AT-3-2 AUTOMATIC TRANSMISSION
3. (a) (b)
-
AUTOMATIC TRANSMISSION SYSTEM
TRANSMISSION FILL Fill the transmission with the correct amount of fluid as listed in the table below. Reinstall the refill plug to avoid fluid splash. Repair
Fill Amount
Transmission pan and drain plug removal
1.3 liters (1.37 US qts, 1.14 Imp. qts)
Transmission valve body removal
3.9 liters (4.12 US qts, 3.43 Imp. qts)
Torque converter removal
5.3 liters (5.60 US qts, 4.66 Imp. qts)
Entire transmission assembly
5.3 liters (5.60 US qts, 4.66 Imp. qts)
HINT: If you cannot add the listed amount of fluid, do the following: (1) Install the refill plug. (2) Allow the engine to idle with air conditioning OFF. (3) Move the shift lever through entire gear range to circulate fluid. (4) Wait for 30 seconds with the engine idling. (5) Stop the engine. (6) Remove the refill plug and add fluid. (7) Reinstall the refill plug. 4. FLUID CIRCULATION (a) Allow the engine to idle with the air conditioning OFF. (b) Move the shift lever through entire gear range to circulate fluid.
CG
1 2 3 4 5 6 7 8 9 10 11 12 13 1415 16
DLC3
TC A04550
5. FLUID TEMPERATURE CHECK NOTICE: The fluid temperature should be less than 30 C (86 F) before beginning the fluid temperature check. (a) With hand-held tester (1) Connect the hand-held tester to the DLC3. (2) Select the tester menus: OBD/MOBD, ENGINE, DATA LIST and A/T. (3) Check A/T OIL TEMP. (4) Allow the engine to idle until the fluid temperature reaches 46 C (115 F).
2004 LAND CRUISER (RM1071U)
Author :
Date :
1856
AT-3-3 AUTOMATIC TRANSMISSION
(b)
Overflow Tube
D14352
-
AUTOMATIC TRANSMISSION SYSTEM
Without hand-held tester (Using A/T OIL TEMP indicator) (1) Connect terminals between CG (4) and TC (13) of the DLC3 using SST (09843-18040). (2) Move the shift lever back and forth between N and D at 1.5 seconds interval for six seconds. (3) The D shift indicator on the combination meter comes on for two seconds. This indicates that the fluid temperature check mode has been started. (4) The D shift indicator comes on again when the fluid temperature reaches 46 C (115 F) and blinks when it exceeds 56 C (130 F). (5) Allow the engine to idle until the fluid temperature reaches 46 C (115 F).
6. FLUID LEVEL CHECK NOTICE: The fluid temperature must be between 46 C (115 F) and 56 C (130 F) to check the fluid level. (a) Remove the overflow plug with the engine idling. (b) Check that the fluid comes out of the overflow tube. If fluid does not come out, proceed to step 7. If fluid comes out, wait until the overflow slows to a trickle and proceed to step 8. 7. (a) (b) (c) (d) (e) (f) 8. (a) (b) (c)
TRANSMISSION REFILL Install the overflow plug. Stop the engine. Remove the refill plug. Add 0.4 liters (0.42 US qts, 0.35 lmp. qts) of fluid. Allow the engine to idle and wait for 10 seconds. Proceed to step 6. COMPLETE Install the overflow plug with a new gasket. Stop the engine. Install the refill plug with a new gasket. Torque: 20 N⋅m (205 kgf⋅cm, 15 ft⋅lbf) for overflow plug 39 N⋅m (400 kgf⋅cm, 29 ft⋅lbf) for refill plug
2004 LAND CRUISER (RM1071U)
Author :
Date :
1857
AT-1 AUTOMATIC TRANSMISSION
-
AUTOMATIC TRANSMISSION SYSTEM
AUTOMATIC TRANSMISSION SYSTEM AT07L-02
PRECAUTION If the vehicle is equipped with a mobile communication system, refer to the precautions in the IN section.
2004 LAND CRUISER (RM1071U)
Author :
Date :
1852
AT-29 AUTOMATIC TRANSMISSION
-
AUTOMATIC TRANSMISSION UNIT
AUTOMATIC TRANSMISSION UNIT AT080-04
COMPONENTS Air Cleaner Cap
Transfer Shift Lever Knob
Radiator Reservoir
Upper Console Panel
Fan and Fluid Coupling Assembly
Transfer Shift Lever Boot
5.4 (55, 48 in.路lbf)
Fan Shroud RH Front Exhaust Pipe
106 (1,080, 78)
106 (1,080, 78)
Transfer Shift Lever Transmission with Transfer
Front Propeller Shaft 80 (820, 59) 80 (820, 59)
Oil Cooler Pipe
Rear Propeller Shaft
71 (724, 52) 106 (1,080, 78)
x6 Ground Cable
20 (204, 15)
Transmission Shift Control Rod
12 (122, 9)
34 (347, 25)
Clip Pin
x4 x4
Torque Converter Clutch
80 (820, 59)
37 (377, 27) 80 (820, 59)
48 (490, 35)
LH Front Exhaust Pipe
x6
Hole Plug
Engine Mouting Insulator RR
18 (185, 13)
Crossmember 59 (600, 43)
Engine No. 1 Under Cover
50 (510, 37) 74 (750, 54) 50 (510, 37)
Engine No. 2 Under Cover 29 (296, 21)
29 (296, 21)
N路m (kgf路cm, ft路lbf) : Specified torque Non-reusable part
29 (296, 21)
Transfer Case Protector D13664
2004 LAND CRUISER (RM1071U)
Author :
Date :
1883