2 00 5 - 2 0 0 6 —-
SERVIC
ANUAL
.rr,
\
X500FE/F FOURTRAX FOREMAN
HOW TO USE THIS MANUAL
CONTENTS
This service manual describes the service procedures for the TRX500FE/FMA"M.
GENERAL INFORMATION
Follow the Maintenance Schedule (Section 4) recommendations to ensure that the vehicle is in peak operating condition and the emission levels are within the standards set by the U.S. Environmental Protection Agency (EPA) and California Air Resources Board (CARB).
TECHNICAL FEATURES FRAME/BODY PANELS/EXHAUST SYSTEM
Performing the first scheduled maintenance is very important. It compensates for the initial wear that occurs during the break-in period.
MAINTENANCE
Sections 1 and 4 apply to the whole vehicle. Section 3 illustrates procedures for removal/installation of components that may be required to perform service described in the following sections. Sections 5 through 23 describe parts of the vehicle, grouped according to location.
LUBRICATION SYSTEM FUEL SYSTEM
Find the section you want on this page, then turn to the table of contents on the first page of the section. Most sections start with an assembly or system illustration, service information and troubleshooting for the section. The subsequent pages give detailed procedure. If you are not familiar with this vehicle, read Technical Features in Section 2.
ENGINE REMOVAL/INSTALLATION LU Z
u LU
CYLINDER/PISTON CLUTCH/GEARSHIFT LINKAGE
If you don't know the source of the trouble, go to section 25 Troubleshooting. Your safety, and the safety of others, is very important. To help you make informed decisions we have provided safety messages and other information throughout this manual. Of course, it is not practical or possible to warn you about all the hazards associated with servicing this vehicle. You must use your own good judgement. You will find important safety information in a variety of forms including: • Safety Labels - on the vehicle • Safety Messages - preceded by a safety alert symbol A and one of three signal words, DANGER, WARNING, or CAUTION. These signal words mean: You WILL be KILLED or SERIOUSLY ADANGER HURT if you don't follow instructions.
CYLINDER HEAD/VALVE
ALTERNATOR/STARTER CLUTCH CRANKCASE/TRANSMISSION/CRANKSHAFT/ BALANCER FRONT WHEEL/SUSPENSION/STEERING CO
(0 (0
REAR WHEEL/SUSPENSION BRAKE SYSTEM
<
u
FRONT DRIVING MECHANISM (FM/FE models)
A WARNING
You CAN be KILLED or SERIOUSLY HURT if you don't follow instructions.
REAR DRIVING MECHANISM
ACAUTION
You CAN be HURT if you don't follow instructions.
BATTERY/CHARGING SYSTEM
Instructions - how to service this vehicle correctly and safely.
As you read this manual, you will find information that is preceded by a | NOTICE | symbol. The purpose of this message is to help prevent damage to your vehicle, other property, or the environment.
IGNITION SYSTEM
<
u oc o UJ
ALL INFORMATION, ILLUSTRATIONS, DIRECTIONS AND SPECIFICATIONS INCLUDED IN THIS PUBLICATION ARE BASED ON THE LATEST PRODUCT INFORMATION AVAILABLE AT THE TIME OF APPROVAL FOR PRINTING. Honda Motor Co., Ltd. RESERVES THE RIGHT TO MAKE CHANGES AT ANY TIME WITHOUT NOTICE AND WITHOUT INCURRING ANY OBLIGATION WHATSOEVER. NO PART OF THIS PUBLICATION MAY BE REPRODUCED WITHOUT WRITTEN PERMISSION. THIS MANUAL IS WRITTEN FOR PERSONS WHO HAVE ACQUIRED BASIC KNOWLEDGE OF MAINTENANCE ON Honda MOTORCYCLES, MOTOR SCOOTERS OR ATVS. Honda Motor Co., Ltd. SERVICE PUBLICATION OFFICE
Date of Issue: November, 2004 ©Honda Motor Co., Ltd.
111
ELECTRIC STARTER LIGHTS/METERS/SWITCHES ELECTRIC SHIFT PROGRAM (ESP: FE model) SELECTABLE 4WD SYSTEM (FM/FE models) WIRING DIAGRAMS TROUBLESHOOTING INDEX
SYMBOLS The symbols used throughout this manual show specific service procedures. If supplementary information is required pertaining to these symbols, it would be explained specifically in the text without the use of the symbols.
Replace the part(s) with new one(s) before assembly.
Use the recommended engine oil, unless otherwise specified.
Use molybdenum oil solution (mixture of the engine oil and molybdenum grease in a ratio of 1:1)
Use multi-purpose grease (lithium based multi-purpose grease NLGI #2 or equivalent). Use molybdenum disulfide grease (containing more than 3% molybdenum disulfide, NLGI #2 or equivalent). Example: MolykoteÂŽ BR-2 plus manufactured by Dow Corning U.S.A. Multi-purpose M-2 manufactured by Mitsubishi Oil, Japan Use molybdenum disulfide paste (containing more than 40% molybdenum disulfide, NLGI #2 or equivalent). Example: MolykoteÂŽ G-n Paste manufactured by Dow Corning U.S.A. Honda Moly 60 (U.S.A. only) Rocol ASP manufactured by Rocol Limited, U.K. Rocol Paste manufactured by Sumico Lubricant, Japan Use silicone grease.
Apply a locking agent. Use a medium strength locking agent unless otherwise specified.
Apply sealant.
Use DOT 4 brake fluid. Use the recommended brake fluid unless otherwise specified.
Use fork or suspension fluid.
1. GENERAL INFORMATION
SERVICE RULES
1-2
BRAKE SYSTEM SPECIFICATIONS
1-11
MODEL IDENTIFICATION
1-2
FRONT DRIVING MECHANISM SPECIFICATIONS (FM/FE models)
1-11
REAR DRIVING MECHANISM SPECIFICATIONS
1-11
BATTERY/CHARGING SYSTEM SPECIFICATIONS
1-11
IGNITION SYSTEM SPECIFICATIONS
1-12
ELECTRIC STARTER SPECIFICATIONS
1-12
LIGHTS/METERS/SWITCHES SPECIFICATIONS
1-12
STANDARD TORQUE VALUES
1-13
ENGINE & FRAME TORQUE VALUES
1-13
LUBRICATION & SEAL POINTS
1-18
CABLE & HARNESS ROUTING
1-22
EMISSION CONTROL SYSTEMS
1-38
GENERAL SPECIFICATIONS
1-5
LUBRICATION SYSTEM SPECIFICATIONS
1-8
FUEL SYSTEM SPECIFICATIONS
1-8
CYLINDER HEAD/VALVE SPECIFICATIONS CYLINDER/PISTON SPECIFICATIONS
1-8 1-9
CLUTCH/GEARSHIFT LINKAGE SPECIFICATIONS ALTERNATOR/STARTER CLUTCH SPECIFICATIONS CRANKCASE/TRANSMISSION/CRANKSHAFT/BALANCER SPECIFICATIONS
1-9
1-9
1-10
FRONT WHEEL/SUSPENSION/STEERING SPECIFICATIONS 1-10 REAR WHEEL/SUSPENSION SPECIFICATIONS
1-10
1-1
GENERAL INFORMATION
SERVICE RULES 1. Use genuine HONDA or HONDA-recommended parts and lubricants or their equivalents. Parts that don't meet HONDA'S design specifications may cause damage to the vehicle. 2. Use the special tools designed for this product to avoid damage and incorrect assembly. 3. Use only metric tools when servicing the vehicle. Metric bolts, nuts and screws are not interchangeable with English fasteners. 4. Install new gaskets, O-rings, cotter pins, and lock plates when reassembling. 5. When tightening bolts or nuts, begin with the larger diameter or inner bolt first. Then tighten to the specified torque diagonally in incremental steps unless a particular sequence is specified. 6. Clean parts in cleaning solvent upon disassembly. Lubricate any sliding surfaces before reassembly. 7. After reassembly, check all parts for proper installation and operation. 8. Route all electrical wires as shown in the Cable & Harness routing (page 1-22).
MODEL IDENTIFICATION This manual covers 3 types of TRX500 models: • TM - 2WD/Left foot operated gearshift • FM - 4WD/Left foot operated gearshift • FE - 4WD/Electric shift program (ESP) Be sure to refer to the procedure that pertains to the appropriate version of the TRX500. TRX500 FE model shown:
DESTINATION CODES Throughout this manual, the following codes are used to identify individual types for each region. DESTINATION CODE A
REGION U.S.A.
CM
Canada
U
Australia (New Zealand)
1-2
GENERAL INFORMATION The Vehicle Identification Number (VIN) is stamped on the front side of the frame.
VIN
The engine serial number is stamped on the left side of the rear crankcase.
ENGINE SERIAL NUMBER The name plate (U.S.A. and U type) or safety certification label (Canada type) is attached on the right front frame pipe.
U.S.A. and U type:
NAME PLATE Canada type:
SAFETY CERTIFICATION LABEL
1-3
GENERAL INFORMATION The carburetor identification number is stamped on the left side of the carburetor body.
CARBURETOR IDENTIFICATION NUMBER
The vehicle emission information label is attached on the rear fender behind the seat (U.S.A. only).
EMISSION CONTROL INFORMATION LABEL The color label is attached on the front side of the right front frame pipe. When ordering color-coded parts, always specify the designated color code.
COLOR LABEL
1-4
GENERAL INFORMATION
GENERAL SPECIFICATIONS TRX500TM DIMENSIONS
FRAME
ENGINE
CARBURETOR
ITEM Overall length Overall width Overall height Wheelbase Front tread Rear tread Seat height Footpeg height Ground clearance Dry weight Curb weight Maximum weight capacity Frame type Front suspension Front wheel travel Front damper Rear suspension Rear wheel travel Rear damper Front tire size Rear tire size Front rim size Rear rim size Front tire brand Rear tire brand Front brake Rear brake Caster angle Trail length Camber angle Fuel tank capacity Fuel tank reserve capacity Cylinder arrangement Bore and stroke Displacement Compression ratio Valve train Intake valve opens closes Exhaust valve opens closes Lubrication system Oil pump type Cooling system Air filtration Engine dry weight Carburetor type Throttle bore
SPECIFICATIONS 2,109 mm (83.0 in) 1,188 mm (46.8 in) 1,169 mm (46.0 in) 1,292 mm (50.9 in) 922 mm (36.3 in) 925 mm (36.4 in) 860 mm (33.9 in) 349 mm (13.7 in) 190 mm (7.5 in) 253 kg (558 lbs) 265 kg (584 lbs) 220 kg (485 lbs) Double cradle Double wishbone 170 mm (6.7 in) Double tube Swingarm 170 mm (6.7 in) Double tube AT25x8-12 • • AT25x 10-12 • • 12x6.0 AT 12x7.5 AT KT181 (Dunlop) KT185 (Dunlop) Hydraulic disc brake Mechanical drum brake 5° 17 mm (11/16 in) 0° 15.8 liters (4.17 US gal, 3.48 Imp gal) 3.3 liters (0.87 US gal, 0.73 Imp gal) Single cylinder, longitudinally installed 92.0x71.5 mm (3.62x2.81 in) 475.3 cm 3 (28.99 cu-in) 8.3: 1 OHV 6° BTDC (at 1 mm lift) 44° ABDC (at 1 mm lift) 42° BBDC (at 1 mm lift) 4° ATDC (at 1 mm lift) Forced pressure and wet sump Trochoid Air cooled (with cooling fan and oil cooler) Oiled double urethane foam 55.2 kg (121.7 lbs) Constant Vacuum (VE type) 36 mm (1.42 in)
1-5
GENERAL INFORMATION DRIVE TRAIN
ELECTRICAL
ITEM Clutch system Clutch operation system Transmission Primary reduction Secondary reduction Final reduction Gearratio 1st 2nd 3rd 4th 5th Reverse Gearshift pattern Ignition system Starting system Charging system Regulator/rectifier Lighting system
SPECIFICATIONS
Centrifugal and multi-plate, wet Automatic Constant mesh, 5-speeds with reverse 2.103 (61/29) 1.818 (40/22) 3.153(41/13) 4.231 (55/13) 2.389(43/18) 1.609 (37/23) 1.179(33/28) 0.848 (28/33) 5.600(28/15x39/13) R-N-1-2-3-4-5 Left foot operated return system DC-CDI Electric starter motor and emergency recoil starter Triple phase output alternator FET shorted, triple phase full wave rectification Battery
TRX500FM/FE DIMENSIONS
ITEM Overall length Overall width Overall height Wheelbase Front tread Rear tread Seat height Footpeg height Ground clearance Dry weight Curb weight Maximum weight capacity
1-6
SPECIFICATIONS
2,109 mm (83.0 in) 1,188 mm (46.8 in) 1,181 mm (46.5 in) 1,287 mm (50.7 in) 913 mm (35.9 in) 925 mm (36.4 in) 860 mm (33.9 in) 349 mm (13.7 in) 190 mm (7.5 in) FM: 270 kg (595 lbs) FE: 271 kg (597 lbs) FM: 282 kg (622 lbs) FE: 284 kg (626 lbs) 220 kg (485 lbs)
GENERAL INFORMATION ITEM Frame type Front suspension Front wheel travel Front damper Rear suspension Rear wheel travel Rear damper Front tire size Rear tire size Front rim size Rear rim size Front tire brand Rear tire brand Front brake Rear brake Caster angle Trail length Camber angle Fuel tank capacity Fuel tank reserve capacity
SPECIFICATIONS Double cradle Double wish-bone 170 mm (6.7 in) Double tube Swingarm 170 mm (6.7 in) Double tube AT25x8-12 • • AT25x 10-12 • • 12x6.0 AT 12x7.5 AT KT181 (Dunlop) KT185(Dunlop) Hydraulic disc brake Mechanical drum brake 2° 9 mm (11/32 in) 0° 15.8 liters (4.17 US gal, 3.48 Imp gal) 3.3 liters (0.87 US gal, 0.73 Imp gal)
ENGINE
Cylinder arrangement Bore and stroke Displacement Compression ratio Valve train Intake valve opens closes Exhaust valve opens closes Lubrication system Oil pump type Cooling system Air filtration Engine dry weight
CARBURETOR
Carburetor type Throttle bore Clutch system Clutch operation system Transmission Primary reduction Secondary reduction Final reduction Front Rear Gearratio 1st 2nd 3rd 4th 5th Reverse Gearshift pattern
Single cylinder, longitudinally installed 92.0x71.5 mm (3.62x2.81 in) 475.3 cm 3 (28.99 cu-in) 8.3: 1 OHV 6° BTDC (at 1 mm lift) 44°ABDC(at 1 mm lift) 42° BBDC (at 1 mm lift) 4° ATDC (at 1 mm lift) Forced pressure and wet sump Trochoid Air cooled (with cooling fan and oil cooler) Oiled double urethane foam FM: 55.5 kg (122.4 lbs) FE: 57.7 kg (127.2 lbs) Constant Vacuum (VE type) 36 mm (1.42 in) Centrifugal and multi-plate, wet Automatic Constant mesh, 5-speeds with reverse 2.103(61/29) 1.818(40/22) 3.230 (42/13) 3.153(41/13) 4.231 (55/13) 2.389 (43/18) 1.609 (37/23) 1.179(33/28) 0.848 (28/33) 5.600(28/15x39/13) R _ N _ 1_ 2 - 3 - 4 - 5 FM: Left foot operated return system FE: Electric shift (left hand operated) return system
FRAME
DRIVE TRAIN
ELECTRICAL
Ignition system Starting system Charging system Regulator/rectifier Lighting system
DC-CDI Electric starter motor and emergency recoil starter Triple phase output alternator FET shorted, triple phase full wave rectification Battery
1-7
GENERAL INFORMATION
LUBRICATION SYSTEM SPECIFICATIONS ITEM After draining Engine oil capacity After draining/filter change After disassembly Recommended engine oil
Oil pump
Tip clearance Body clearance Side clearance
STANDARD 2.4 liters (2.5 US qt, 2.1 Imp qt) 2.5 liters (2.6 US qt, 2.2 Imp qt) 3.0 liters (3.2 US qt, 2.6 Imp qt) Pro Honda GN4 or HP4 (without molybdenum additives) 4-stroke oil or equivalent motor oil API service classification: SG or Higher JASO T 903 standard: MA Viscosity: SAE 10W-40 0.15(0.006) 0.15-0.21 (0.00-0.008) 0.02-0.09(0.001 -0.004)
Unit: mm (in) SERVICE LIMIT
-
-
0.20 (0.008) 0.25 (0.010) 0.11 (0.004)
FUEL SYSTEM SPECIFICATIONS ITEM Carburetor identification number Main jet Slow jet Pilot screw opening Float level Idle speed Throttle lever free play
SPECIFICATIONS VE6DA #162 #45 See page 6-19 15.9 mm (0.63 in) 1,400 ± 100 rpm (min"1) 3 - 8 mm (1/8-5/16 in)
CYLINDER HEAD/VALVE SPECIFICATIONS ITEM Cylinder compression at 380 rpm (min"1) Valve clearance Valve, valve Valve stem O.D. guide Valve guide I.D. Stem-to-guide clearance
Valve spring Rocker arm
Camshaft and cam follower
Valve seat width Free length Arm I.D. Shaft O.D. Arm-to-shaft clearance Cam lobe height
Cam follower O.D. Follower bore I.D. Follower-to-bore clearance Cylinder head warpage
1-8
IN/EX IN EX IN/EX IN EX IN/EX Inner Outer IN/EX IN/EX IN/EX IN EX IN/EX IN/EX IN/EX
STANDARD 440 kPa (4.5 kgf/cm3, 64 psi) 0.15 + 0.02(0.006 + 0.001) 5.975 - 5.990 (0.2352 - 0.2358) 5.955 - 5.970 (0.2344 - 0.2350) 6.000 - 6.012 (0.2362 - 0.2366) 0.010 - 0.037 (0.0004 - 0.0015) 0.030 - 0.057 (0.0012 - 0.0022) 1.2 (0.05) 42.94(1.691) 43.63(1.718) 12.000 - 12.018 (0.4724 - 0.4731) 11.964 - 11.984 (0.4710 - 0.4718) 0.016 - 0.054 (0.0006 - 0.0021) 35.8315 - 35.9915 (1.41069 - 1.41699) 35.5512 - 35.7112 (1.39965 - 1.40595) 22.467 - 22.482 (0.8845 - 0.8851) 22.510 - 22.526 (0.8862 - 0.8868) 0.028 - 0.059 (0.0011 - 0.0023) -
Unit: mm (in) SERVICE LIMIT 5.95 (0.234) 5.93 (0.233) 6.02 (0.237) 0.12(0.005) 0.14 (0.006) 1.5(0.06) 42.08(1.657) 42.76 (1.683) 12.05 (0.474) 11.92 (0.469) 0.08 (0.003) 35.60(1.402) 35.38 (1.393) 22.46 (0.884) 22.54 (0.887) 0.07 (0.003) 0.10 (0.004)
Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING
NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
GENERAL INFORMATION
CYLINDER/PISTON SPECIFICATIONS ITEM Cylinder
I.D. Out-of-round Taper Warpage Piston, Piston O.D. at 15 (0.6) from bottom piston pin, Piston pin hole I.D. piston ring Piston pin O.D. Piston-to-piston pin clearance Piston ring end gap Top Second Oil (side rail) Piston ring-to-ring Top groove clearance Second Cylinder-to-piston clearance Connecting rod small end I.D. Connecting rod-to-piston pin clearance
STANDARD 92.000 - 92.010 (3.6220 - 3.3.6224) 91.965 - 91.985 (3.6207 - 3.6214) 20.002 - 20.008 (0.7875 - 0.7877) 19.994 - 20.000 (0.7872 - 0.7874) 0.002 - 0.014 (0.0001 - 0.0006) 0.15-0.30(0.006-0.012) 0.30-0.45(0.012-0.018) 0.20-0.70(0.008-0.028) 0.030 - 0.060 (0.0012 - 0.0024) 0.030 - 0.060 (0.0012 - 0.0024) 0.015 - 0.045 (0.0006 - 0.0018) 20.020 - 20.041 (0.7882 - 0.7890) 0.020 - 0.047 (0.0008 - 0.0019)
Unit: mm (in) SERVICE LIMIT 92.10 (3.626) 0.10 (0.004) 0.10 (0.004) 0.10 (0.004) 91.93 (3.619) 20.04 (0.789) 19.96 (0.786) 0.08 (0.003) 0.5 (0.02) 0.6(0.02) 0.9 (0.04) 0.09 (0.004) 0.09 (0.004) 0.10 (0.004) 20.07 (0.790) 0.10 (0.004)
CLUTCH/GEARSHIFT LINKAGE SPECIFICATIONS Change clutch
ITEM Spring free length Disc thickness Plate warpage Outer I.D. Outer guide
Centrifugal clutch
Primary drive gear
STANDARD TM/FM FE
I.D. O.D. Mainshaft O.D. at clutch outer guide Drum I.D. Weight lining thickness Clutch spring height Clutch weight spring free length Gear I.D. Crankshaft O.D. at drive gear
43.8(1.72) 42.5 (1.67) 2.62-2.78(0.103-0.109) 29.000-29.021 (1.1417-1.1426) 22.000-22.021 (0.8661 -0.8670) 28.959 - 28.980 (1.1401 - 1.1409) 21.967 - 21.980 (0.8648 - 0.8654) 150.0-150.2(5.906-5.913) 2.0 (0.08) 3.72(0.146) 23.17(0.912) 29.000-29.021 (1.1417-1.1426) 28.959 - 28.980 (1.1401 - 1.1409)
Unit: mm (in) SERVICE LIMIT 42.49(1.673) 41.23 (1.623) 2.3 (0.09) 0.20 (0.008) 29.05(1.144) 22.05 (0.868) 28.93(1.139) 21.93 (0.863) 150.4(5.92) 1.3 (0.05) 3.6(0.14) 24.10 (0.949) 29.05 (1.144) 28.93(1.139)
ALTERNATOR/STARTER CLUTCH SPECIFICATIONS ITEM Starter driven gear boss O.D.
STANDARD 51.705 - 51.718 (2.0356 - 2.0361)
Unit: mm (in) SERVICE LIMIT 51.69 (2.035)
1-9
GENERAL INFORMATION
CRANKCASE/TRANSMISSION/CRANKSHAFT/BALANCER SPECIFICATIONS ITEM Shift fork
I.D.
Transmission
Claw thickness Shaft O.D. Gear I.D.
Gear bushing O.D.
Gear-to-bushing clearance
Gear bushing I.D. Mainshaft O.D.
Crankshaft
Front, center Rear
M4 M5 C1,C2, C3, CR Reverse idle M4 M5 C1 C2, CR C3 M4 M5 C1 C2, CR C3 M4 M5 atM4 atM5
Reverse idle shaft O.D. Bushing-to-shaft M4 clearance M5 Reverse idle gear-to-shaft clearance Runout Big end side clearance Big end radial clearance
STANDARD 13.000-13.021 (0.5118-0.5126) 13.000 - 13.018 (0.5118 - 0.5125) 4.93-5.00(0.194-0.197) 12.966 - 12.984 (0.5105 - 0.5112) 25.000-25.021 (0.9843-0.9851) 20.000-20.021 (0.7874-0.7882) 28.020-28.041 (1.1031 -1.1040) 13.000-13.021 (0.5118-0.5126) 24.959 - 24.980 (0.9826 - 0.9835) 19.966 - 19.984 (0.7861 - 0.7868) 27.986 - 28.005 (1.1018 - 1.1026) 27.979 - 28.000 (1.1015 - 1.1024) 27.959 - 27.980 (1.1007 - 1.1016) 0.020 - 0.062 (0.0008 - 0.0024) 0.016 - 0.055 (0.0006 - 0.0022) 0.015 - 0.055 (0.0006 - 0.0022) 0.020 - 0.062 (0.0008 - 0.0024) 0.040 - 0.082 (0.0016 - 0.0032) 22.000-22.021 (0.8661-0.8670) 17.016 - 17.034 (0.6699 - 0.6706) 21.959 - 21.980 (0.8645 - 0.8654) 16.976 - 16.987 (0.6683 - 0.6688) 12.966 - 12.984 (0.5105 - 0.5112) 0.020 - 0.062 (0.0008 - 0.0024) 0.029 - 0.058 (0.0011 - 0.0023) 0.016 - 0.055 (0.0006 - 0.0022) 0.05-0.65(0.002-0.026) 0.006 - 0.018 (0.0002 - 0.0007)
Unit: mm (in) SERVICE LIMIT 13.04(0.513) 13.04(0.513) 4.5(0.18) 12.96(0.510) 25.05 (0.986) 20.05 (0.789) 28.07 (1.105) 13.04(0.513) 24.93(0.981) 19.94 (0.785) 27.94(1.100) 27.93 (1.100) 27.91 (1.099) 0.10(0.004) 0.10 (0.004) 0.08 (0.003) 0.10 (0.004) 0.15(0.006) 22.04 (0.868) 17.06 (0.672) 21.93 (0.863) 16.93 (0.667) 12.94(0.509) 0.10 (0.004) 0.10 (0.004) 0.10(0.004) 0.15(0.006) 0.8 (0.03) 0.05 (0.002)
FRONT WHEEL/SUSPENSION/STEERING SPECIFICATIONS ITEM Minimum tire tread depth Cold tire pressure
Tie-rod distance between the ball joints Toe
Standard Minimum Maximum With cargo TM FM/FE TM FM/FE
STANDARD kgf/cm2, 3.6 psi) kgf/cm2, 3.2 psi) kgf/cm2, 4.0 psi) kgf/cm2, 3.6 psi)
25 kPa (0.25 22 kPa (0.22 28 kPa (0.28 25 kPa (0.25 382.5(15.06) 388.0(15.28) Toe-out: 1 ± 15 (1/32 ± 19/32) Toe-out: 30 ± 15 (1-3/16 ± 19/32)
Unit: mm (in) SERVICE LIMIT 4.0(0.16) -
REAR WHEEL/SUSPENSION SPECIFICATIONS ITEM Minimum tire tread depth Cold tire pressure
1-10
Standard Minimum Maximum With cargo
25 22 28 25
kPa (0.25 kPa (0.22 kPa (0.28 kPa (0.25
STANDARD kgf/cm2, 3.6 psi) kgf/cm2, 3.2 psi) kgf/cm2, 4.0 psi) kgf/cm2, 3.6 psi)
Unit: mm (in) SERVICE LIMIT 4.0(0.16) -
GENERAL INFORMATION
BRAKE SYSTEM SPECIFICATIONS Front brake
Rear brake
ITEM Recommended brake fluid Disc thickness Disc runout Master cylinder I.D. Caliper cylinder I.D. Drum I.D. Shoe lining thickness
Unit: mm (in) SERVICE LIMIT 3.0(0.12) 0.30 (0.012) 181 (7.1) To index mark
STANDARD Honda DOT 4 brake fluid 3.8-4.2(0.15-0.17) 14.0 (0.55) 33.96 (1.3379 180.0 (7.09) 5.3(0.21)
FRONT DRIVING MECHANISM SPECIFICATIONS (FM/FE models) Front differential
ITEM Oil capacity
After draining After disassembly
Recommended oil Gear backlash Backlash difference Slip torque Face cam-to-housing distance Differential ring gear depth Cone spring free height
Unit: mm (in) SERVICE LIMIT
STANDARD 185 cm 3 (6.3 US oz, 6.5 Imp oz) 230 cm3 (7.8 US oz, 8.1 Imp oz) Hypoid gear oil SAE # 80 0.05-0.25(0.002-0.010) 14-17N-m(1.45-1.75kgfm, 1 0 - 13 Ibf-ft) 3.3-3.7(0.13-0.15) 6.55-6.65(0.258-0.262) 2.8(0.11)
0.4 (0.02) 0.2(0.01) 12N-m(1.2 kgfm, 9 Ibf-ft) 3.3(0.13) 6.55 (0.258) 2.6(0.10)
REAR DRIVING MECHANISM SPECIFICATIONS ITEM Axle runout Rear final drive
Oil capacity
After draining After disassembly
Recommended oil Gear backlash Backlash difference Ring gear-to-stop pin clearance
STANDARD 75 cm 3 (2.5 US oz, 2.6 Imp oz) 100 cm 3 (3.4 US oz, 3.5 Imp oz) Hypoid gear oil SAE # 80 0.05-0.25(0.002-0.010) 0.3-0.6(0.01-0.02)
Unit: mm (in) SERVICE LIMIT 3.0(0.12) 0.4 (0.02) 0.2(0.01) -
BATTERY/CHARGING SYSTEM SPECIFICATIONS Battery
Alternator
ITEM Capacity Current leakage Voltage Fully charged (20째C/68째F) Needs charging Charging Normal current Quick Capacity Charging coil resistance (20째C/68째F)
SPECIFICATIONS
12V-12Ah 1 mA max. 13.0-13.2 V Below 12.3 V 1.4Ax5-10h 6.0 Ax 1.0 h 0.357 kW/5,000 rpm (min'1) 0.1 -1.0 Q
1-11
GENERAL INFORMATION
IGNITION SYSTEM SPECIFICATIONS ITEM Spark plug Spark plug gap Ignition coil primary peak voltage Ignition pulse generator peak voltage Ignition timing ("F" mark)
SPECIFICATIONS BKR5E-11 (NGK), K16PR-U11 (DENSO) 1.0-1.1 mm (0.039-0.043 in) 100 V minimum 0.7 V minimum 10° BTDC at idle
ELECTRIC STARTER SPECIFICATIONS ITEM Starter motor brush length
STANDARD 12.5 (0.49)
Unit: mm (in) SERVICE LIMIT 9.0 (0.35)
LIGHTS/METERS/SWITCHES SPECIFICATIONS Bulbs
ITEM Headlight (high/low beam) Assist headlight Brake/taillight Neutral indicator Reverse indicator Oil temperature indicator
Fuse
1-12
4WD indicator (FM/FE only) Meter light Main fuse TM/FM FE Sub-fuse
SPECIFICATIONS 12V-30/30Wx2 12V-45W 12V-21/5Wx2 12 V-1.7 W (A/CM type TM model) LED (Except A/CM type TM model) 12 V-1.7 W (A/CM type TM model) LED (Except A/CM type TM model) 12 V-1.7 W (A/CM type TM model) LED (Except A/CM type TM model) LED LED x 10 (Except A/CM type TM model) 30 A 30 A x 2 15Ax2,10Ax2