ZIP H2Lure Cage Mount Kit Installation Guide

ZIP H2Lure Cage Mount Kit Installation Guide For luring and prefeeding

1

ZIP H2Lure Installation Guide – when fitting to a cage trap The ZIP H2Lure is designed to provide continuous lure to improve the efficiency of cage trapping operations.

This guide provides instructions of two methods to secure the H2Lure to your cage trap: Option 1: Using cable ties or wire Option 2: Mounting the device on to a panel, for a more secure attachment. The panel size can vary from 70 × 80mm (i.e. the size of the H2Lure cage mount plastic piece), to the full dimensions of the cage itself, which will shield the dispensed lure from rain.

The instructions for attaching the H2Lure and stainelss cover are the same for both options once the cage mount plastic piece has been attached.

2

Parts provided [1] 14G × 50mm TEK Screw × 2

[3] Set screw and wing nut

[2] Cage mount plastic piece

[4] Stainless steel cover pieces × 2

Gear required (not provided) [5] H2 Lure

[7] Battery drill or impact driver

[6] Cage trap

[8] Gloves

IF USING CABLE TIES [9] 2 cable ties (or wire) – minimum length of 200mm IF MOUNTING TO A PANEL [10] A piece of hard material* such as stainless steel, wood or hard plastic to attach the cage mount plastic piece to – at least as large as the cage mount plastic piece (70 x 80 mm) *This will be your panel

[11] 3.5mm drill bit (must be sufficient to drill through stainless steel, if using) [12] 14G 3-3.5mm drill bit (must be sufficient to drill through stainless steel, if using) [13] Deburring tool (if using stainless steel)

3

Option 1: Using cable ties or wire

Instructions The mayonnaise will dispense through the central hole of the black cage mount plastic piece.

Begin by determining where this needs to be positioned on the cage to maximise the attractiveness of the trap to your target species.

4

1. Attach the cage mount plastic piece to the possum cage using cable ties or wire.

Option 2: Using a piece of stainless steel, hard plastic, or wood

1. Using the 3.5mm drill bit, drill a hole in the panel, using the black plastic piece as a template. The lure will be dispensed through this hole If using stainless steel sheeting as your panel, remove the cage mount plastic piece and use the deburring tool on the drilled hole to remove any metal splinters.

2. Using the 3.5mm 14G drill bit, attach the cage mount plastic piece to the panel using the TEK screws, using any of the four holes. The TEK screws provided are 25mm.

If your panel is very thick, you may need to use longer screws.

5

Attaching the H2Lure and stainless covers

The method for attaching the H2Lure and stainelss cover are the same for both options.

1. Put the set screw through the edge of the cage mount plastic piece.

2. Attach the wingnut loosely

6

3. Remove the domed lid from the H2Lure

4. Screw the H2Lure into the plastic piece by hand. Line up the scale with the recessed section of the cage mount plastic piece – the opposite side to the wingnut

5. Fit the three sided stainless cover, lining up the cut outs in the stainless cover with the tabs on the cage mount plastic piece

6. Fit the second stainless piece with the wingnut on the outside, and hand tighten the wingnut

7

Quick Guide OPTION 1 - CABLE TIES OR WIRE

1 Determine where H2Lure needs to be

fitted for the mayonnaise to dispense in the right spot.

2 Attach cage mount plastic piece to top

of the cage using cable ties or wire.

OPTION 2 – MOUNTING TO A PANEL

1 Determine where H2Lure needs to be

fitted for the mayonnaise to dispense in the right spot.

2 Using 3.5mm drill bit, drill hole in panel.

3 Using 3.5m 14G drill bit, attach the cage

mount plastic piece using the two TEK screws provided to the panel.

8

ATTACHING THE H2LURE AND STAINLESS COVER

1 Put the set screw and wingnut

through the cage mount plastic piece.

2 Remove the domed end cap

from the H2Lure.

3 Lightly screw the H2Lure into the

cage mount plastic piece, by hand.

4 Fit the three sided stainless cover,

lining up the cut outs in the stainless cover with the tabs on the cage mount plastic piece.

5 Fit the second stainless piece so that

the wingnut is on the outside.

6 Hand tighten the wingnut.

Troubleshooting It can take up to two weeks for the mayonnaise to begin dispensing from the H2Lure. The hydrogen cell is turned on when the device is rotated with the lure scale the right way up. You may wish to rotate the device to turn it on before you deploy it.

Alternatively, you can take another source of mayonnaise with you to place around the site until the H2Lure begins to dispense. We recommend Best Foods/Hellman’s brand egg mayonnaise.

If the device fails to dispense two weeks after being rotated, get in touch with us at products@zip.org.nz The H2Lure will last a minimum of 10 months.

Additional devices are available to purchase as required. Contact products@zip.org.nz.

The H2Lure and Tree Mount kit are both covered by a six-month warranty.

Empty H2Lures can be returned to us for refilling. Contact products@zip.org.nz for more information.

9

This installation guide is current as at

June 2025.

From time to time, we may make improvements – check out our website, zip.org.nz, for the latest version!

If you would like to share your feedback or suggestions, please contact us at products@zip.org.nz.

zip.org.nz zip.org.nz