3M SPEEDGLAS MAINTENANCE / RECORD CARD

Welding Safety

Speedglas Consumables Optimization.

How to maintain and get the most out of your Speedglas.

Welding Safety

To optimise the effective lifetime of your welding equipment and avoid the additional cost of replacement, regular maintenance is important.

For maximum safety and comfort, make it a regular habit to check and change the following items at the intervals recommended below or more frequently as required: System

Component

Typically replaced

Notes

Welding Filters

Outer Protection Plate

Once a week

Replace anytime the plate becomes deeply pitted, scratched or too dirty to clean with soft cloth or lens paper.

Welding Filters

Inner Cover Plate

Once a month

Regularly clean with a soft cloth and replace if any pits or scratches occur.

Welding Helmets

Visor Plate

Every two weeks

Replace more often if visibility is reduced.

Welding Helmets

Sweatband

Once a month

Replace more often if sweatband becomes unhygienic.

Respirators

Prefilter

2 days to once a week Regular replacement of the prefilter extends the (based on application & life of the particle filter, saving money while also environment) helping the battery run-time.

Respirators

Particle Filter

At least every month

For Adflo respirator, replace when particle filter indicator becomes red. Otherwise, replace whenever the battery operating time becomes too short, or when “fully loaded� filter triggers low airflow alarm.

Respirators

Gas Filter

As needed

Replace the gas filter according to your work place requirements. It is not recommended to wait until you can sense odours or smells.

Respirators

Odour Filter

Any time you smell unpleasant odours

Odour filter is not required if gas filter is used.

Respirators

Spark Arrestor

As needed

Replace if deformed and no longer fitting well.

Respirators

Breathing Tube

If damaged, deformed or leaking any air

To Extend the life of the breathing tube, use a tube cover or a heavy duty rubber breathing tube.

Welding Helmets with Face Seal Respirators

At least every 2 months Replace earlier in really dirty environments, or if it has splits or tears or whenever the seal becomes unhygienic.

Adflo Systems

If damaged, deformed or leaking any air

Breathing Tubes

To extend the life of breathing tube, use a tube cover or a heavy-duty rubber breathing tube.

Important Notice: Note that higher-than-normal levels of pollutants, heat and sparks will require more frequent replacement of components. Chart assumes minimum 4 hours usage per day.

3M™ Speedglas™ Heavy Duty Welding Helmet G5-01 G5-01 Component

SAP ID

ADF

Description

7100016691

526000

Outer protection plate (standard)

7000000223

527000

Outer protection plate (scratch-resistant)

7100108831

527001

Outer protection plate (extra scratch-resistant)

7100016690

527070

Outer protection plate (heat-resistant)

Inner Protection Plate

7000000227

528025

Inner protection plate for Speedglas G5-01 Auto-Darkening Filter

Grinding Visors

7100190170

613000

3M™ Visor Plate, Anti-Fog and Hard coated, for 3M™ Speedglas™ Welding Helmet G5-01, 613000, 5 EA/Case

Face Seals

7100161510

614000

3M™ Face Seal for 3M™ Speedglas™ Welding Helmet G5-01, 614000, 1 EA/Case

7100169234

198016

3M™ Speedglas™ Sweatband, Towelling, 198016, 3 EA/Case

7100190171

198018

3M™ Speedglas™ Sweatband, Leather, 198018, 1 EA/Case

7100173404

198017

3M™ Speedglas™ Sweatband in fleecy cotton, pkg of 3 - 198017

7100182269

613700

3M™ Airduct Breathing Tube (short) incl. holder for 3M™ Speedglas™ Welding Helmet G5-01, 613700, 1 EA/Case

Outer Protection Plates

Helmet

Short-ID

Sweatbands

Short Breathing Tubes

Additional Accessory Options for G5-01 A. Helmet in standard configuration with rigid neck protection and the smaller, fabric head protection.

B. To better enable you to weld when looking down, replace the rigid neck protection with, for example the smaller fabric neck protection (169041).

A

C

B

E

F

D

G

C. Increase coverage of your head, neck and chest by adding the larger fabric head cover (169023) and/or the extended fabric neck protection (169042).

D. For increased visibility at all times, add the flurescent yellow extended head protection (169021).

E. When you need the durability of leather, attach the leather head protector (169022) and the leather neck protector (169043).

F. To maximize coverage from sparks add the fabric shroud (169030) and the extended or larger fabric head protection (169023).

G. Task light (169200)

3M™ Speedglas™ Welding Helmet G5-02

Helmet

ADF

G5-02 Component

SAP ID

Short-ID

Description

Outer Protection Plates

7100205305

626000

Scratch resistant outer protection plate, pkg of 5

Inner Protection Plates

7100202350

624000

Inner protection plates, pkg of 2

Magnifying Lens Options

7100202361

172020

Magnifying lens x1.5

7100202360

172021

Magnifying lens x2.0

7100202396

172022

Magnifying lens x2.5

7100080223

168010

Sweatband in fleecy cotton (length 24cm), pkg of 2

Sweatbands Large Head Rests

7100080253

167520

Sweatband, towelling, purple, pkg of 2

7000044367

168000

Sweatband, leather

7100189980

536211

Large Head Rest

3

3M™ Speedglas™ Welding Helmet 9100 FX Air 9100FX Air Component

ADF

Outer Protection Plates

Inner Protection Plates

Short-ID

Description

7100016691

526000

Outer protection plate (standard)

7000000223

527000

Outer protection plate (scratch-resistant)

7100108831

527001

Outer protection plate (extra scratch-resistant)

7100016690

527070

Outer protection plate (heat-resistant)

7000000225

528005

Inner protection plate for Speedglas 9100V Auto-Darkening Filter

7000000226

528015

Inner protection plate for Speedglas 9100X Auto-Darkening Filter

7000000227

528025

Inner protection plate for Speedglas 9100XX and 9100XXi Auto-Darkening Filter

7000000236

523000

Spare visor for Speedglas 9100 FX Welding Helmet

7100080231

523001

Spare anti-fog visor for Speedglas 9100 FX Welding Helmet

Sweatbands

7000000224

168015

Sweatband for Speedglas 9100 Series Welding Helmets

Short Breathing Tubes

7100167262

533500

Airduct assembly for Speedglas 9100 FX Air

Air Deflectors

7000044540

535000

Air deflector for Speedglas 9100 FX Air Welding Helmet

Grinding Visors Helmet

SAP ID

Additional Accessory Options 9100 FX Air Extended protective headcover for Speedglas 9100 FX Welding Helmets (Large) 169007 7100167240

Extended protective throat and ear cover for Speedglas 9100 Series Welding Helmets 169010 7000000230

3M™ Speedglas™ Welding Helmet 9100MP & MP Lite 9100FX Air Component

SAP ID 7100016691

ADF

Outer Protection Plates

Inner Protection Plates

Helmet

Grinding Visors Face Seals Sweatbands

Short-ID

Description

526000

Outer protection plate (standard)

7000000223

527000

Outer protection plate (scratch-resistant)

7100108831

527001

Outer protection plate (extra scratch-resistant)

7100016690

527070

Outer protection plate (heat-resistant)

7000000225

528005

Inner protection plate for Speedglas 9100V Auto-Darkening Filter

7000000226

528015

Inner protection plate for Speedglas 9100X Auto-Darkening Filter

7000000227

528025

Inner protection plate for Speedglas 9100XX and 9100XXi Auto-Darkening Filter

7000000236

523000

Spare visor for Speedglas 9100 FX Welding Helmet

7100080231

523001

Spare anti-fog visor for Speedglas 9100 FX Welding Helmet

7100167292

534200

Face Seal for Speedglas 9100MP Welding Helmet

7100080223

168010

Sweatband 9100 MP pack of two

7100112082

168011

Sweatband 9100 MP Lite pack of two

Additional Accessory Options 9100MP & MP Lite Shroud for 9100 MP/9100 MP-Lite 169015 7100106682

Cover for MP/MP-Lite Safety helmet 169014 7100167334

4

health problems

Select respiratory protection that is adequate Illnesses due to welding fume often take and suitable for the worker and the task many years to develop.

including bronchial asthma, chronic obstructive pulmonary disease (COPD) and lung cancer

3M™ Adflo™ Powered Air Purifying Respirator System SAP ID

Short-ID

7100080248

Filters

Metal fume fever (high temperatures, chills, aches, vomiting, weakness and fatigue).

Fast fact:

Stomach ulcers, kidney damage and nervous system damage

Nausea

7000028075 Disposable respirators – Reusable837542 respirators –

4 regular smoker and a 40% • Original 3-panel design

3M™ Aura™ Particulate Click™ 70000280433M™ Secure 837242 Respirators 9300+ Reusable Respirator 7000028074 HF-800 Series 837110 Series

Symptoms of metal fume fever may be more noticeable on a Monday, after some days without exposure.3

Headaches

Reusable respirators – The dangers of

Description

Disposable respirators – Prefilter, pkg of 5 3M™ Aura™ Particulate Fast fact: Respirators Particle Filter,9300+ pkg of 2 Welders have the same risk Series of chronic bronchitis Gas Filter A2 as a

836010 increase of heart attack and837012 stroke

7100116817

Dizziness

Larynx and urinary tract cancers

Lung function abnormalities

Adflo Components

Eye, nose and throat irritation

allows

Gas Filter A1B1E1 higher of lung cancermovement for risk greater facial

3M™ Secure Click™ Long-term Reusable Respirator welding fume HF-800 Series health problems • Helps provide protection against

Illnesses solid due toand welding often take liquidfume particles and/or many years to develop.

What is welding fume?

than non-welders.

1

gases and vapours, depending •Odour Available in FFP1, FFP2 and Filter FFP3 protection levels 7000044586 837120 Odour Filter Pad against to provide protection • Original 3-panel design allows • Helps provide protection against Larynx and solid and liquid particles for greater facial movement particles and/or urinary tract 7000028067 solid and liquid 834016 Standard self adjusting QRS NPF of 40 • With valved and unvalved gases and vapours, depending Lung function cancers • Available in FFP1, FFP2 and abnormalities All welding fume contains particles as well as gases. models, our respirators feature • 3M P3 with additional relief Breathing Tube 7000044527 834017 Heavy-duty rubber QRS FFP3 protection levels including Weldingbronchial fume particles vary in size, from Stomach particles that are ulcers, an innovative chin tab for easy from nuisance odours caused to provide protection against asthma, chronic large like grains of sand through to tiny particles damage 7000028062 834018 Cover adjustments and an embossed, obstructive by welding are suggested forkidneythat pulmonary solid and liquid particles cannot be seen by the naked eye and can easily be inhaled. and nervous and welding application. sculpted upper panel to help disease (COPD) typical NPF ofThe 40 type and quantity of welding system damage • With valved and unvalved lung cancer Spark arrestor 7000028010 836000 Spark fume, gases and vapours are reduceArrestor eyewear fogging as carcinogenic1, and models, our respirators feature • 3M P3determined with additional relief by the material, Welding Helmet to welding fume and other gases associated with • Lightweight and designed to exposureSpeedglas™ welding process, amperage an innovative chin tab for easy from nuisance odours caused welding can cause a range of health issues. and the welding electrode fit under virtually any welding increase of adjustments and an embossed, by welding are suggested for used Fast fact: heart attack helmet and cartridges available, sculpted upper panel to help typical welding application. and stroke Welders have the same risk depending on your combination reduce eyewear fogging Consult an expert to identify the • Maintenance-free (disposable) of chronic bronchitis as a Fast fact: hazardsWelding levels against country of contaminants: particulates, Speedglas™ Helmet • Lightweight and designed to regular smoker4 and a 40% safety standards Poor respiratory protection is the fourth organic and inorganic vapours, fit under virtually any welding most common workplace violation. higher risk of lung cancer2 Fast fact: acid gas and ammonia 1 helmet and cartridges available,

Assess your workers’ risk

The dangers of Why is it important to regularly welding fume The dangers of maintain your equipment? welding fumeof The dangers Short-term What is Assess your welding fume health problems welding fume? workers’ risk than non-welders.

depending on your combination of contaminants: particulates, organic and inorganic vapours, acid gas and ammonia

• Maintenance-free (disposable)

What is welding fume?

What is welding fume?

All welding fume contains particles as well as gases.

Welding fume particles vary in size, from particles that are large like grains of sand through to tiny particles that cannot be seen by the naked eye and can easily be inhaled.

All welding fume contains particles as well as gases.

1 Welding fume particles vary in size, from particles that are , and as carcinogenic large like grains of sand through to tiny particles that with exposure to welding fume and other gases associated cannot be seen by the naked andissues. can easily be inhaled. welding can cause a range of eye health All welding fume contains particles as well as gases.

Welding fume particles vary in size, from particles that are 1 , and as carcinogenic large like grains of sand through to tiny particles that with exposure to welding fume and other gases associated cannot be seen by the naked andissues. can easily be inhaled. welding can cause a range ofeye health

safety professional or consultant can conduct area and personal exposure monitoring to determine type and concentration of contaminants.

The type and quantity of welding fume, gases and vapours are determined by the material, welding process, amperage and the welding electrode used

Before you choose your protective Air Respirator Supplied Air Respirator equipmentPowered system - 3M™ Speedglas™ system - 3M™ Speedglas™ Fast fact: Eye, nose Dizziness Consult an expert to identify the and throat hazards levels against country irritation safety standards

The Hierarchy of Controls can be Welding used to guideHelmet you throughG5-01 the process of mitigating exposures to welding fume.5 The measures towards the top of the list are normally considered Powered Air Respirator Supplied Air Respirator Powered Air Respirator Most exposure to welding fume and other gases associated with to be the most preferable. system 3M™ Speedglas™ system 3M™ Speedglas™ Eliminate the hazard. E.g. Use welding can cause a range of health issues.

Most • NPF of up to 500 (inward

Fast fact:

Poor respiratory protection is the fourth 1 2 , and as carcinogenic most common workplace violation.

Fast fact:

Welding Helmet G5-01 G5-01 ATE Hierarchy of Controls Poor respiratory protection is the fourth Welding Helmet

Short-term health problems Short-term health problems Short-term health problems

ATE Hierarchy of Controls ELIMINATE of Controls ATE Powered Respirator Supplied AirHierarchy Regulator FastAir fact: Poor respiratory protection is the fourth V-500E ATE • NPF of upcommon to 500workplace (inward violation.

ELIMINATE most ELIMINATE ATE SUBSTITUTE leakage according to TH3) • NPF of 200 (3B) most common workplace violation.2

2

• Helps provide protection against solid and liquid particles and/or gases and vapours, depending upon the combination

design for extra Eye, nose • Slim Dizziness Metalmobility fume fever and comfortable(high work and throat temperatures, chills, aches, vomiting, irritation weakness and fatigue).

Eye, nose and throat irritation

Dizziness

Metal fume fever

Eye, nose and throat irritation Nausea

Dizziness

Headaches

Nausea

Headaches

Symptoms of metal Metal fume fever fume fever may

(high temperatures, be more noticeable chills, aches, vomiting, on a Monday, after weakness and fatigue).

Fast fact: some days without

Headaches

Fast Fastfact: fact:

Illnesses due to welding fume often take many years to develop.

References: 1

Administrative controls.

E.g. Introduce dedicated welding areas and regular testing of LEV

more determine type noticeable

Most

Before you choose Long-term your protective health problems equipment

Illnesses due to welding fume often take many years to develop.

The Hierarchy of Controls can be used to guide you through the process of mitigating exposures to welding fume.5 The measures towards the top of the list are normally considered to be the most preferable.

Larynx and

Request a demo now

Personal Protective Equipment will still be required for most manual welding due to the hazards

ADMINISTRATIVE areas andextraction regular testing of LEV on-tool RATIVE ADMINISTRATIVE involved andIntroduce the limitationsdedicated of E.g. welding CONTROLS LS CONTROLS other controls.

Least

Administrative controls. areas and regular testing of LEV E.g. Introduce dedicated welding Administrative controls. areas and regular testing of LEV RATIVE Personal Protective Equipment will PPE E.g. Introduce dedicated welding PPE LS still be required for most manual Administrative controls. areas Protective and regularEquipment testing of LEV Personal will RATIVE welding due to the hazards E.g.

Introduce dedicated welding LS still be required for most manual Least involved the limitations of areas and and regular testing of LEV 3M designs and manufactures PPE to help Personal Equipment willprotect welders and weldingProtective due to the hazards other controls. nearby workers from wide of hazards associated with stillinvolved bethe required forrange most manual and the limitations of Personal Protective Equipment will welding, grinding and other metal working processes. welding due to the hazards other controls. still be required for limitations most manual involved and the of Personal Protective Equipment will welding due to the hazards other controls. still be required for most manual involved and the limitations of welding due to the hazards other controls. involved and the limitations of other controls.

RATIVE LS

Fast fact:

3 of metal Symptoms exposure. fume fever may be more noticeable on a Monday, after some days without Symptoms3 of metal exposure.

40-50 UK welders are hospitalised every year with fume fever may be pneumonia caused by welding fume. Two of these more noticeable on a Monday, after welders die every year.3 some days without exposure.3

Long-term health problems Long-term health problems Long-term health problems Nausea

PPE

safety professional or consultant can

Fast fact: conduct area and Supplied Air Regulator Symptoms personal of exposure metal fume V-500E monitoring to be fever may

onand a Monday, concentration after • NPF of 200 (3B) Nausea Headaches some days without of contaminants.

• Helps provide protection Most exposure.3 • Can be used to protect against Eliminate amount of welding the hazard. E.g. Use amount of welding Most Substitute the hazard. against solid and liquid particles Most substances with poor warning Most Eliminate the hazard. E.g. Use Substitute the hazard.

Substitute the hazard.gases and/or and amount oftechnique welding properties (taste or smell) or welding thatvapours, or weldingproduces technique thatless contaminants depending upon Substitute the hazard. oramount welding thatthe combination oftechnique welding produces less contaminants • Belt-mounted regulator with produces less contaminants Eliminate the hazard.Most E.g. Use amount of welding

Use engineering controls to isolate workers from the hazard. E.g. local exhaust ventilation (LEV) or on-tool extraction

ADMINISTRATIVE CONTROLS

Welding Helmet G5-01

Eliminate the hazard. E.g. Use

Substitute thetechnique hazard. that or welding • Can be used to protect against produces less contaminants SUBSTITUTE Substitute the hazard.

• design substances withSUBSTITUTE poor warning orSlim welding technique for that extra mobility ENGINEERING Use engineering controls to isolate produces less contaminants work CONTROLS andfrom comfortable properties (taste or smell) G workers the hazard. or welding technique thatE.g. local Use engineering controls to isolate exhaust ventilation (LEV) or produces less contaminants LS G workers from the hazard. E.g. local on-tool extraction • Belt-mounted regulator with Use engineering controls to or isolate exhaust ventilation (LEV) LS ENGINEERING ENGINEERING G workers the hazard. E.g. local on-toolfrom extraction CONTROLS CONTROLS Use engineering controls toor isolate exhaust ventilation (LEV) LS G workers the hazard. E.g. local on-toolfrom extraction Use engineering controls to isolate exhaust ventilation (LEV) or LS G Administrative workers from controls. the hazard. E.g. local on-tool extraction RATIVE E.g.

Introduce dedicated welding exhaust ventilation (LEV) or LS LS Administrative controls.

Request aFast demo fact: now (high temperatures, chills, aches, vomiting, weakness and fatigue).

Eliminate the hazard. E.g. Use

leakage amount according of weldingto TH3)

Metal fume fever

(high temperatures, chills, aches, vomiting, weakness and fatigue).

urinary tract cancers

Lung function Hierarchy of Controls abnormalities including bronchial ELIMINATE

Eliminate the hazard. E.g. Use

Fast fact:

Choosing the right respirator

Least

amount of welding

Substitute the hazard.

or welding technique that produces less contaminants

40-50 UK welders are hospitalised every year with Least pneumoniaLeast caused by welding fume. Two of these welders die every year.3of ENGINEERING increase Least heart attack and stroke

CONTROLS

Use engineering controls to isolate workers from the hazard. E.g. local exhaust ventilation (LEV) or on-tool extraction

Fast fact:

Welders have the same risk ADMINISTRATIVE CONTROLS

References: 1

of chronic bronchitis as a Administrative controls.

E.g. Introduce dedicated welding areas and regular testing of LEV

regular smoker4 and a 40% higher risk of lung cancer

IARC2017

PPE

Personal Protective Equipment will still be required for most manual welding due to the hazards involved and the limitations of other controls.

than non-welders.

Top 10 Most Frequently Cited Standards, OSHA, U.S. Department of Labor, for 2015.

Select respiratory protection that2 is adequate 3 and suitable for the worker and the task www.hse.gov.uk/welding/illness.htm (02.03.2017) Source:

IARC2017

10 Most Frequently Cited Standards, OSHA, U.S. Department of Labor, for 2015.

Illnesses due to Top welding fume often take 3 Larynx and many years to develop.

Source: www.hse.gov.uk/welding/illness.htm (02.03.2017) 2

urinary tract 4 chronic bronchitis: Impact of smoking and welding, 2012 Lung function Incidence and prevalence ofcancers abnormalities Illnesses due to5 Source: weldinghttps://www.cdc.gov/niosh/topics/hierarchy/ fume often take including bronchial 6 many years to develop.

Stomach ulcers,protection factor based on NPF = Nominal Protection Factor.

Theand nominal Larynx asthma, chronic laboratory-measured performance data according to European Standards. The protection kidney damage urinary tract obstructive pulmonary Lung function factor is assigned by local authorities in each European country and can therefore be and nervous cancers disease (COPD) and abnormalities system damage lung cancer including bronchial Larynx and Stomach ulcers,

Most

Stomach ulcers, kidney damage and nervous system damage

asthma, chronic Least obstructive pulmonary Leastdisease (COPD) and SUBSTITUTE lung cancer

1 Least

Fast fact: your Assess workers’ risk

4

Incidence and prevalence of chronic bronchitis: Impact of smoking and welding, 2012

5

Source: https://www.cdc.gov/niosh/topics/hierarchy/

6

NPF = Nominal Protection Factor. The nominal factor based on PPE to help protect welders and 3Mprotection designs and manufactures laboratory-measured performance data according European The protection nearbyto workers fromStandards. the wide range of hazards associated with factor is assigned by local authorities in eachwelding, European country and canmetal therefore be processes. grinding and other working

The type and quantity of welding fume, gases and vapours are determined by the material, welding process, amperage and the welding electrode used

Choosing the

5

Welding Record Card

Welding Safety

Care and Maintenance.

To maintain protection levels, optimise the effective lifetime of the system and avoid the additional cost of replacement, it is extremely important to carry out regular checks on your equipment.

Maintenance Record ID

Company Name

System ID

Company Address

Headtop Type Postcode Equipment issued to Equipment maintained by

Maintenance / Cleaning Checklist Date

Headtop

Turbo (incl. airflow)

Parts Replaced

Signature

As part of COSHH regulation requirements, record cards such as this must be used to record the monthly checks for each system.

6

Welding Record Card

Welding Safety

Maintenance / Cleaning Checklist Date

Headtop

Turbo (incl. airflow)

Parts Replaced

Signature

As part of COSHH regulation requirements, record cards such as this must be used to record the monthly checks for each system.

7

Welding Record Card Welding Safety

Maintenance / Cleaning Checklist Date

Headtop

Turbo (incl. airflow)

Parts Replaced

Signature

As part of COSHH regulation requirements, record cards such as this must be used to record the monthly checks for each system.

8

YouTube Video Links for - G5-01 Replace Face Seal https://www.youtube.com/ watch?v=RdLlaGM7y0Q&list=PL6kbXORMpTVFyepTS5ZXCzM4TAMQIiVbf&index=6&t=0s

Replace The Hinge https://www.youtube.com/watch?v=cwfUO_ WdCbI&list=PL6kbXORMpTVFyepTS5ZXCzM4TAMQIiVbf&index=14&t=0s

Full Playlist for the G5-01 https://www.youtube.com/playlist?list=PL6kbXORMpTVFyepTS5ZXCzM4TAMQIiVbf

How to Replace Headband https://multimedia.3m.com/mws/media/1620071O/3m-hmt-g501-video-replace-headband-mp4. mp4 https://youtu.be/6IPAJTgnhzE

How to Change Protection Plate https://multimedia.3m.com/mws/media/1631796O/3m-hmt-g501-video-change-task-lightprotection-plate.mp4 https://youtu.be/Ix4Gv175EcY

How to operate task light https://multimedia.3m.com/mws/media/1631873O/ https://youtu.be/Ix4Gv175EcY

How to use breathing tube cover https://multimedia.3m.com/mws/media/1631874O/ https://youtu.be/iFtL1W-T4q0

YouTube Video Links for - G5-02 How to replace the outer protection plate http://gpimmedia.3m.com/appserver/main/opennodeview. do?tab=assetlocationtab&nodeId=1384114&assetId=1657670

How to add the headband cushion part https://multimedia.3m.com/mws/media/1684839O/how-to-video-speedglas-headband-g502.mp4

How to replace the battery https://multimedia.3m.com/mws/media/1684845O/how-to-video-speedglas-adf-battery-g502. mp4

How to replace the inner protection plate https://multimedia.3m.com/mws/media/1684846O/how-to-video-speedglas-welding-filter-g502. mp4

The 3M Speedglas Welding Helmet G5-02 – Reliable protection https://www.youtube.com/watch?v=69OoifEmlis&list=PL6kbXORMpTVHXksDvxb_e-TdxosUgADVo

How to replace the G5-02 outer protection plate https://www.youtube.com/watch?v=5yht0Z6acT0

YouTube Video Links for - 9100FX Air Replace Face Seal https://www.youtube.com/ watch?v=huRh40c6JqY&list=PL6kbXORMpTVGG3BDvQQII5VPp3E9zFSE4&index=38&t=0s

Replace Air Deflector https://www.youtube.com/watch?v=-Y6O2WxwUzw&list=PL6kbXORMpTVGG3BDvQQII5VPp3E9z FSE4&index=6&t=0s

Replace Hinge https://www.youtube.com/ watch?v=zk1WsTvlGvA&list=PL6kbXORMpTVGG3BDvQQII5VPp3E9zFSE4&index=39&t=0s

General 9100 Playlist https://www.youtube.com/playlist?list=PL6kbXORMpTVGmX1crjZ9pwNdT9K1DY4GE

YouTube Video Links for - 9100MP and MP Lite Replace Face Seal https://www.youtube.com/watch?v=dhW7-aFCUqk&list=PL6kbXORMpTVGG3BDvQQII5VPp3E9zF SE4&index=25&t=0s

Add Earmuffs https://www.youtube.com/ watch?v=zzVPBMka4yg&list=PL6kbXORMpTVGG3BDvQQII5VPp3E9zFSE4&index=19&t=0s

Replace Harness https://www.youtube.com/watch?v=r7df_2b_0Z4&list=PL6kbXORMpTVFVkm40Lh1mO9UaHStFfpP&index=9&t=0s

General 9100 MP Playlist https://www.youtube.com/playlist?list=PL6kbXORMpTVFVkm4-0Lh1mO9UaHStFfpP

YouTube Video Links for - Adflo Adflo Use and Checks https://www.youtube.com/watch?v=g2UaWgCRqRA&list=PL96D2544B044DE116&index=19&t=0s

Welding Safety

For more information please contact.

3M United Kingdom PLC 3M Centre, Cain Road Bracknell RG12 8HT Bershire +44 (0) 845 6025 237 www.3M.co.uk

3M Ireland Limited The Iveagh Building Carrickmines Park Dublin 18 D18 X015 +353 (0) 1 2803555 www.3MIreland.ie

WWW.UNITEDWELDING.CO.UK

www.3m.co.uk/safety www.3M.co.uk/G5-01 www.3M.co.uk/G5-02

www.facebook.com/3MSpeedglas Scan this QR-code to see videos and learn more about care and maintenance of your Speedglas welding helmet.

www.youtube.com/3MSpeedglas www.instagram.com/3MSpeedglas