3 minute read

Engine - Engine and crankcase

necessary , adjust the V - belt tension

T o adjust the V - belt loosen the setscrew (S) and move the alternator (A) tighten the Vbelt.

Advertisement

(Adjust the V - belt tension inserting a bar

After replacing with a new V - belt and adjusting run the engine for 5 min and readjust the deflection the value the table

After replacing with a new V - belt and adjusting it, run the engine for 5 min and readjust the deflection the value the table

V isually check the V - belt for oiliness wear any , replace the V - belt with new

Engine - Inspect – Every hours

sure check the following points before starting engine every day .

No.

Fuel tank drain

Fuel system bleeding

Inspection item

Battery electrolyte level check and battery recharging

Fuel tank drain

Prepare a waste oil container collecting waste

Remove the drain plug (D) the fuel tank (F) drain (water , from the fuel tank

Drain until fuel with water and dust flow

Then tighten the drain plug firmly

Fuel system bleeding

Bleed the fuel system according the following

When there air the fuel the fuel jection pump (FI) will not able

Check the fuel oil level the fuel Refuel insuf

Open the cock (FC) the water separator (W)

Loosen the air bleeding bolt (A) the water rator turning counterclockwise 2 - 3 times using a screwdriver a spanner .

When the fuel coming out clear and not mixed with any tighten the air bleeding bolt (A)

Feed fuel with the fuel priming pump (FP) tro - magnetic fuel feed

• case the engine uses the electro - magnetic fuel feed

T urn the starter switch the “ON” position and hold the position for - s operate the fuel feed

• case the engine uses the electro - magnetic fuel feed pump (FP)

The priming pump the top the fuel filter

Move the priming pump and down feed fuel until feel your hand slightly heavy .

• W ater separator (W)

(Installed the pipe line)

• Fuel filter (FF)

(Mounting with fuel priming pump) (option)

Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL.NOWAITING

NOTE:

If there is no response to click on the link above, please download the PDF document first and then clickonit.

Battery electrolyte level check and battery recharging

W Arning

Hazardous chemicals!

Battery electrolyte contains sulfuric acid. Contact with skin and eyes could result severe irritation and Always wear splash - proof goggles and protective clothing (gloves and W ash hands after handling.

Failure comply could result death serious injury

W Arning

Battery acid causes burns. Batteries contain sulfuric acid.

A void contact with eyes Antidote (external): Flush with water Antidote (eyes): flush with water for minutes and seek medical attention immediately . Antidote (internal): Drink large quantities water milk. not induce vomiting. Seek medical attention immediately .

Failure comply could result death serious injury

NOTICE: Make sure turn off the battery switch disconnect the negative cable ( before inspecting the electrical Failure could cause short - circuiting and Always disconnect the ( Negative battery cable first before disconnecting the battery cables from battery dental - may cause fire and personal injury

And remember connect the ( Negative battery cable (back onto the battery) LAST

NOTICE: Keep the area around the battery well paying attention keep away any fire During operation hydrogen gas generated from the battery and can easily

Electrolyte level

• Check the electrolyte level (EL) the battery When the amount fluid nears the lower limit (LL) , fill with battery fluid (available the market) the upper limit (UL) operation continues with insuf ficient battery the battery life and the battery may overheat and

• Battery fluid tends evaporate more quickly the summer , and the fluid level should checked lier than the specified

• the engine cranking speed slow that the gine does not start recharge the battery

• the engine still will not start after replace the battery

• Remove the battery from the battery mounting the machine unit after daily use letting the machine unit leave the place that the ambient temperature could drop ( ) And store the battery a warm place until the next use the unit start the engine easily low ambient

Battery charge

Use a battery tester hydrometer and check the battery the battery recharge

Measurement with a battery tester (BT)

When checking the battery with the batter tester , connect the red clip the tester the battery positive (+) terminal and black clip the battery negative ( terminal ing them securely , and judge the battery charge level from the indicator position.

Green zone: Normal

Y ellow zone: Slightly discharged

Red zone: Defective much discharged

Measurement with hydrometer

When using a hydrometer , the measured specific gravity must corrected according the temperature the time

This article is from: