Page 1

Rev 2:1

133E

FLANGE NECK

Powder Coated Finish

Components Code

Quantity

F

1

Bolt Kit

Description

Flange Neck

Code

Quantity

A G

2 2

w493

Description

12x100 Bolts, Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers

1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.

PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.

Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com

www.towsure.com


Rev 2:1

133E 133ED 133ES

Powder Coated Finish

VAUXHALL MOKKA 2012CHEVROLET TRAX 2013E11 55R-0110092 w614

Components

Mainframe

Description

Bolt Kit

Code

Quantity

CB

1

Crossbar

Code

Quantity

B

6

12x35 Set Screws, Nuts & Grip Washers

LA

1

Left Angle

RA

1

Right Angle

WA

Description

C

2

12x35 Set Screws & Grip Washers

WB

6

12mm Large Round Washers

4

10mm Large Round Washers

(Neck Type) Detachable 'D'

Please See Detachable Neck Box Contents List

Please See Detachable Neck Box Contents List

Swan Neck 'S'

Please See Swan Neck Box Contents List

Please See Swan Neck Box Contents List

Flange Neck 'F'

Please See Flange Neck Box Contents List

Please See Flange Neck Box Contents List

1.

Remove light clusters— 4 nuts behind panels in boot. Remove cover from the side of light cluster to reveal 1 screw & remove. Slide out light cluster and disconnect wiring loom.

2.

Remove bumper— 5 fixings inside each wheel arch. Unclip arch trim to reveal hidden fixings. Remove plastic fixings from lower edge of bumper. Unclip bumper sides & remove whilst disconnecting any wiring.

3.

Remove impact beam & hand to customer but retain fixings. Remove bumper support brackets.

4.

Insert angles LA & RA inside the chassis rails and loosely attach using set screws C with washers WB from under the vehicle. Attach angles LA & RA to the rear panel using set screws B with washers WB & original fixings X with washers WA.

5.

Loosely attach crossbar CB to angles LA & RA using bolts B.

6.

Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.

7.

Cut bumper as shown in diagram.

8.

Refit bumper, lights & any wiring.

Detachable Neck: Attach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB with CPE10 plates (standard orientation) using set screws Y & bolts W. Flange Neck: Attach to crossbar CB using bolts A, then attach type approved towball (not supplied) with set screws G. 9.

Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.

PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.

Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com

www.towsure.com


Rev 2:1

133E 133ED 133ES

Powder Coated Finish

VAUXHALL MOKKA CHEVROLET TRAX

Bolt Torque Settings Bolt Size (mm)

Pitch Torque Setting (mm) (Nm) 8.8 Tensile

5

0.80

6.09

6

1.00

10.50

8

1.25

25.30

10

1.25

46.00

10

1.50

50.90

12

1.25

83.00

12

1.50

87.81

12

1.75

87.27

14

2.00

139.00

16

2.00

213.00

PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.

Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com

www.towsure.com

133E  
133E