Page 1

Rev 2:1

101E

FLANGE NECK

Powder Coated Finish

Components Code

Quantity

F

1

Bolt Kit

Description Flange Neck

Code

Quantity

A

2

12x100 Bolts, Nuts & Grip Washers

G

2

16x50 Set Screws, Nuts & Grip Washers

w493

Description

1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.

PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.

Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com

www.towsure.com


Rev 2:1

101E 101ED 101ES

BMW X1 (E84)

Powder Coated Finish

e11*94/20*9627*00

w

Components

Mainframe

Code

Quantity

CB

1

Description

Bolt Kit Code

Crossbar

Quantity

Description

1

Fitting Instruction

6

Plastic Fixings

(Neck Type) Detachable 'D'

Please See Detachable Neck Box Contents List

Please See Detachable Neck Box Contents List

Swan Neck 'S'

Please See Swan Neck Box Contents List

Please See Swan Neck Box Contents List

Flange Neck 'F'

Please See Flange Neck Box Contents List

Please See Flange Neck Box Contents List

1. Remove rear light clusters, fixings inside boot. 2. Remove bumper—8 fixings on lower edge, 3 fixings in each wheel arch. Pull back lower edge of wheel arch surround trim to reveal 1 fixing in each arch and remove. With the aid of lubricant carefully pull out bumper tips and ease bumper rearwards. Disconnect reversing sensors if fitted. 3. Lower exhaust from hanger on bumper impact beam and remove impact beam. Retain fixings 4. Locate crossbar CB onto threaded studs. Locate impact beam over the crossbar and secure in position using original fixings. Fully tighten. 5. Refit bumper and light clusters. Re attach wheel arch liners using plastic fixings provided. Detachable Neck: Attach to crossbar CB using set screws Z.

Swan Neck: Attach to crossbar CB with CPE10 plates (standard orientation) using set screws Y & bolts W

Flange Neck: Attach to crossbar CB using set screws A. Attach type approved towball using set screws G. 6. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.

PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.

Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com

www.towsure.com


Rev 2:1

101E 101ED 101ES

BMW X1 (E84)

Powder Coated Finish

VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-

Bolt Torque Settings Bolt Size (mm)

Pitch Torque Setting (mm) (Nm) 8.8 Tensile

5

0.80

6.09

6

1.00

10.50

8

1.25

25.30

10

1.25

46.00

10

1.50

50.90

12

1.25

83.00

12

1.50

87.81

12

1.75

87.27

14

2.00

139.00

16

2.00

213.00

PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.

Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com

www.towsure.com

101E  
101E