OSHA Silica Standards - Generic

Page 1

OSHA Silica Standard Pocket Guide


Supervisors Overview What Site Supervisors are responsible for:

• Obtaining a copy of the OSHA Table 1 tool which will allow for ease of safety control instructions for those workers with potential exposures. • Ensuring that all the tools, equipment, PPE and materials (including water) necessary to implement the ECP is available (and in good working order) prior to allowing work activities to commence. • Ensuring that all workers (under the supervisor’s direction and control) have received the necessary education and training applicable to perform tasks with potential exposures to respirable crystalline silica. • Ensuring that workers adhere to the project/task specific ECP, OSHA Table 1 and safety plans, including PPE and personal hygiene practices (i.e. including be clean shaven where the respirator seals to the user’s face where applicable) requirements. • Coordinating work activities with the Contractors as required, and/or otherwise implementing the controls necessary to protect others. • If the site conditions or work performed by another contractor causes exposure to your and or your employees, remove from the immediate area.


OSHA Silica Standard Pocket Guide Handheld Drills Engineering and Work Practice Control Methods Use drill equipped with commercially-available shroud or cowling with duct collection system. Operate and maintain tool in accordance with the manufacturer’s instructions to minimize dust emissions. Dust collector must provide the air flow recommended by the tool manufacturer, or efficiency and filter-cleaning mechanism. Use a HEPA-filtered vacuum when cleaning holes. Required PPE Hand Protection

Eye Protection

Face Shield

GENERAL TASK GLOVES

GOGGLES

IF DRILLING OVERHEAD

Notes

Page 3


OSHA Silica Standard Pocket Guide Handheld Grinders For Use Other Than Mortar Removal Engineering and Work Practice Control Methods For tasks performed outdoors only: Use grinder equipped with an integrated water delivery system that continuously feeds water to the grinding surface. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. OR Use grinder equipped with a commercially available shroud and dust collection system. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Dust collector must provide airflow of 25 or greater cubic feet per minute (CPM) for each inch on the wheel diameter and have a filter with 99% or greater efficiency and cyclonic pre-separator or filter cleaning mechanism. Work Schedule Guide <4 hours/shift

>4 hours/shift

When used outdoors

None

None

When used indoors or in an enclosed area

None

APF10 (n95)

Required PPE Hand Protection

Eye Protection

Face Shield

Respiration Protection

Hearing Protection

GENERAL TASK GLOVES

GOGGLES

REQUIRED

DUST MASK

NON-ACTIVE EAR MUFFS

Page 4


OSHA Silica Standard Pocket Guide Jackhammers and Handheld Powered Chipping Tools Engineering and Work Practice Control Methods Use tool with water delivery system that supplies a continuous stream or spray of water at the point of impact. OR Use tool equipped with a commercially-available shroud and dust collection system. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Dust collector must provide air flow recommended by the tool manufacturer, or greater, and have a filter with 99% efficiency and a filter cleaning mechanism. Work Schedule Guide When used outdoors When used indoors or in an enclosed area

<4 hours/shift

>4 hours/shift

None

APF10 (n95)

APF10 (n95)

APF10 (n95)

Required PPE Hand Protection

Eye Protection

Face Shield

Respiration Protection

Hearing Protection

GENERAL TASK GLOVES

GOGGLES

REQUIRED

DUST MASK

NON-ACTIVE EAR MUFFS

Notes

Page 5


OSHA Silica Standard Pocket Guide Rig-Mounted Core Saws or Drills Engineering and Work Practice Control Methods Use tool equipped with integrated water delivery system that continuously feeds water to the cutting surface. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Required PPE Hand Protection

Eye Protection

GENERAL TASK GLOVES

SAFETY GLASSES

Notes

Page 6


OSHA Silica Standard Pocket Guide Heavy Equipment and Utility Vehicles

For tasks, such as grading and excavating but not including: demolishing, abrading, or fracturing Silica-Containing Materials.

Engineering and Work Practice Control Methods Apply water and/or dust suppressants as necessary to minimize dust emissions. OR When the equipment operator is the only employee engaged in the task, operate equipment from within an enclosed cab. Required PPE Hand Protection

Eye Protection

GENERAL TASK GLOVES

SAFETY GLASSES

Notes

Page 7


OSHA Silica Standard Pocket Guide Power Saws on Concrete Engineering and Work Practice Control Methods Use saw with integrated water delivery system that continuously feeds water to the blade. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Work Schedule Guide When used outdoors When used indoors or in an enclosed area

<4 hours/shift

>4 hours/shift

None

APF10 (n95)

APF10 (n95)

APF10 (n95)

Required PPE Hand Protection

Eye Protection

Face Shield

Respiration Protection

Hearing Protection

GENERAL TASK GLOVES

GOGGLES

IF DRILLING OVERHEAD

DUST MASK

NON-ACTIVE EAR MUFFS

Notes

Page 8


OSHA Silica Standard Pocket Guide Handheld Grinders for Mortar Removal Engineering and Work Practice Control Methods Use grinder equipped with a commercially-available shroud and dust collection system. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Dust collector must provide airflow of 25 or greater cubic feet per minute (CPM) for each inch on the wheel diameter and have a filter with 99% or greater efficiency and a cyclonic pre-separator or filter cleaning mechanism. Work Schedule Guide Silica PPE

<4 hours/shift

>4 hours/shift

APF10 (n95)

APF25

Required PPE Hand Protection

Eye Protection

Face Shield

Respiration Protection

Respiration Protection

GENERAL TASK GLOVES

GOGGLES

IF DRILLING OVERHEAD

DUST MASK

RESPIRATOR

Notes

Page 9


OSHA Silica Standard Pocket Guide Walk-Behind Saws Engineering and Work Practice Control Methods Use saw with integrated water delivery system that continuously feeds water to the blade. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Work Schedule Guide When used outdoors When used indoors or in an enclosed area

<4 hours/shift

>4 hours/shift

None

APF10 (n95)

APF10 (n95)

APF10 (n95)

Required PPE Hand Protection

Eye Protection

Respiration Protection

GENERAL TASK GLOVES

GOGGLES

DUST MASK

Notes

Page 10


OSHA Silica Standard Pocket Guide Stationary Masonry Saws Engineering and Work Practice Control Methods Use saw with integrated water delivery system that continuously feeds water to the blade. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Required PPE Hand Protection

Eye Protection

GENERAL TASK GLOVES

SAFETY GLASSES

Note: While in the immediate area and hazards are present, remove all unnecessary employees / workers from area.

Notes

Page 11


OSHA Silica Standard Pocket Guide Handheld Power Saws

For cutting fiber-cement board and sheet rock

Engineering and Work Practice Control Methods For tasks performed outdoors only: Use saw equipped with commercially available dust collection system. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Dust collector must provide airflow recommended by the tool manufacturer, or greater, and have a filter with 99% or greater efficiency. Required PPE Hand Protection

Eye Protection

GENERAL TASK GLOVES

GOGGLES

Notes

Page 12


OSHA Silica Standard Pocket Guide Drivable Saws Engineering and Work Practice Control Methods For tasks performed outdoors only: Use saw equipped with integrated water delivery system that continuously feeds water to the blade. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Required PPE Hand Protection

Eye Protection

GENERAL TASK GLOVES

SAFETY GLASSES

Notes

Page 13


OSHA Silica Standard Pocket Guide Drivable Milling Machines Engineering and Work Practice Control Methods Use machine equipped with supplemental water spray designed to suppress dust. Water must be combined with a surfactant. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Required PPE Hand Protection

Eye Protection

GENERAL TASK GLOVES

SAFETY GLASSES

Notes

Page 14


OSHA Silica Standard Pocket Guide Walk-Behind Milling Machines and Floor Grinders Engineering and Work Practice Control Methods Use machine equipped with integrated water delivery system that continuously feeds water to the cutting surface. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. OR Use machine equipped with dust collection system recommended by the manufacturer. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Dust collector must provide the air flow recommended by the manufacturer, or greater, and have a filter with 99% or greater efficiency and a filter cleaning mechanism. When used indoors or in an enclosed area. Use a HEPA-filtered vacuum to remove loose dust in between passes. Required PPE Hand Protection

Eye Protection

GENERAL TASK GLOVES

SAFETY GLASSES

Notes

Page 15


OSHA Silica Standard Pocket Guide Vehicle-Mounted Drilling Rigs for Rock And Concrete Engineering and Work Practice Control Methods Use a dust collection system with close capture hood or shroud around drill bit with a low flow water spray to wet the dust at the discharge point from the dust collector. OR Operate from within an enclosed cab and use water for dust suppression on a drill bit Required PPE Hand Protection

Eye Protection

GENERAL TASK GLOVES

SAFETY GLASSES

Notes

Page 16


OSHA Silica Standard Pocket Guide Dowel Drilling Rigs for Concrete Engineering and Work Practice Control Methods For tasks performed outdoors only:

Use shroud around drill with a dust collection system. Dust collector must have a filter with 99% or greater efficiency and a filter cleaning mechanism. Use a HEPA-filtered vacuum when cleaning holes. Work Schedule Guide Silica PPE

<4 hours/shift

>4 hours/shift

APF10 (n95)

APF10 (n95)

Required PPE Hand Protection

Eye Protection

Face Shield

Respiration Protection

GENERAL TASK GLOVES

GOGGLES

IF DRILLING OVERHEAD

DUST MASK

Notes

Page 17


OSHA Silica Standard Pocket Guide Crushing Machines Engineering and Work Practice Control Methods Use equipment designed to deliver water spray or mist for dust suppression at crusher and other points where dust is generated (e.g., hoppers, conveyors, sieves/sizing or vibration components and discharge points. Operate and maintain tool in accordance with manufacturer’s instructions to minimize dust emissions. Use a ventilated booth that provides fresh, climate controlled air to the operator, or a remote-control station. Required PPE Hand Protection

Eye Protection

GENERAL TASK GLOVES

SAFETY GLASSES

Notes

Page 18



OSHA Silica Standard Pocket Guide

DEVELOPED BY

www.tdindustries.com


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.