WALL AND FLOOR CONCRETE APPLICATIONS

STAMPED CONCRETE APPLICATION FAST AND EASY

FIRST DAY-STEP 1: First add to concrete mixer Style Beton Fibbers. The fibbers are very strong to acids and to alkalis and perfectly stable to ultraviolet rays, to bacteria and muffs, have a good adhesion to cement thanks to chemical bonds that develop.

FIRST DAY-STEP 2: Reinforce the concrete floor with a metal grid. Ensure reinforcement, inserts, embedded parts, and formed joints are not disturbed during concrete placement.

FIRST DAY-STEP 3: Deposit concrete so that specified slab thickness will be obtained after finishing operations.

1/3

FIRST DAY-STEP 4: Make the concrete surface smooth, using a trowel.

FIRST DAY-STEP 5: Make the concrete edges smooth, using hand edger.

FIRST DAY-STEP 6: After the concrete surface is poured and floated, Style Beton Color Hardener, which is a tinted, powdery sub-stance blended of mineral-based pigments, portland cement, silica and quartz, is applied and worked into the surface using a trowel.

FIRST DAY-STEP 7: Make the concrete surface smooth, using a trowel.

FIRST DAY-STEP 8: Dust the surface using Style Beton Release Powder, which adds two-tone color on the concrete and prevents the stamps to stick to the surface.

2/3

FIRST DAY-STEP 9: Use proper tamp tools into the stamp surface to achieve the required texture, with uniformity of pattern and depth of stamping.

AFTER THREE DAYS-STEP 10: After the concrete cures, it is rinsed with clean water to remove loose Release Powder.

THE SAME DAY-STEP 11: When the floor is dry, seal, using Style Beton Sealer, a UV resistant sealer that prevents color changes or fading caused by the sun. It is pure acrylic-based resin in virgin solvents for improved clarity and anti-yellowing characteristics.

Visit our website: www.stylebeton.com for more information and videos for all our products.

3/3

NANO-TOP APPLICATION FAST AND EASY SELF LEVELING FLOOR

STEP 1: We spread the surface, where Nano-Top will be applied, with Acrylic Primer.

We continue spreading the surface, where Nano-Top will be applied, with Acrylic Primer.

STEP 2: We mix very well one bag Nano-Top (25kg) with 6 lt fresh and clean water using low speed mixing.

We mix very well one bag Nano-Top (25kg) with 6 lt fresh and clean water using low speed mixing.

1/2

STEP 3: We apply Nano-Top, self leveling flooring.

We apply Nano-Top, self leveling flooring.

STEP 4: We help a little bit in spreading Nano-Top with a trowel or roller.

We help a little bit in spreading Nano-Top with a trowel or roller.

Nano Top is ready.

You can find it in several colors, which can also be combined to each other and create a “unique game of colors� or after the floor is completely dry, it can be applied Acid Stain (see Acid Stain Application).

Visit our website: www.stylebeton.com for more information and videos about all our products.

2/2

DECO PEBBLE APPLICATION FAST AND EASY

FIRST DAY-STEP 1:

We mix every sack of Decopebble (25kg) with 5kg cement, gray or white.

FIRST DAY-STEP 2: We apply on concrete sub-base the mix of Decopebble. a) We apply minimum 2 cm (31,5kg/m²)Decopebble (wet-on-wet) on fresh concrete surface, which we have left to absorb the water. b) We apply minimum 4 cm (63kg/m²) Decopebble on old concrete surface, on which we have applied earlier a coat of Polystyle.

FIRST DAY-STEP 3: We apply the mix.

FIRST DAY-STEP 4: We make the surface smooth and leave the mix to absorb the surface water.

1/2

FIRST DAY-STEP 5: We spread the surface with Style Lack and cover the surface with nylon.

SECOND DAY-STEP 6: We rinse the surface, using water pump and fresh water.

SECOND DAY-STEP 7: Decopebble Floor is ready and we can apply Style Sealer, when the surface is dry.

Visit our website: www.stylebeton.com for more information and videos about all our products.

2/2

DECO CREATE APPLICATION NEW IMPROVED FORMULATION TWO DAYS PROCEDURE – LESS TIME, LESS COST 10 EASY STEPS

STEP 1: Spread the surface, where you will apply Deco Create, with Style Contact.

STEP 2: Mix the ready to made plaster Deco Create with 5 lt (±0,500 Kg) fresh and clean water .

Deco Create should be as thick as shown in the picture.

STEP 3: Apply the first coat Deco Create (1-2mm) and right after that continue with STEP 5. First and second coat should be applied wet to wet.

1/4

STEP 4: Apply the second coat Deco Create (1-5 cm), depending on the pattern of the stamp you have choose.

STEP 5: Make the surface smooth.

STEP 6: Check the difference in thickness between first and second coat.

STEP 7: Apply Style Liquid Release on the stamp, using a brush.

STEP 8: Start stamping the plaster.

Continue stamping, covering all the surface.

2/4

Continue stamping, covering all the surface

STEP 9: The same day, 3-4hours after stamping, Deco Create is still soft and you can correct some details using Deco Create Tools.

STEP 10: The second day you can start coloring using Decochrom, which is in 8 basic colors that you can mix. Try to begin with light colors and small quantities.

You can use sponges to spread the colors on the surface.

It can be used a brush to painted joints, if it is not applicated from the beginning colored plaster Deco Create.

A clean sponge can be used to remove the paint that has come off plaster’s joints.

3/4

This is the final result of stamped wall Deco Create. You can change the color if after some years you don’t like it.

4/4

BRICK-CREATE APPLICATION LESS TIME – LESS COST THAN BRICK

STEP 1: Apply the first coat Deco Create® (1-2mm).

STEP 2:

Apply the second coat Deco Create® (1.5cm) wet on wet.

STEP 3:

Make the surface smooth.

1/3

Make the surface smooth.

STEP 4: Apply the third coat Deco Create速 (2 mm) wet on wet, choosing the desirable color.

STEP 5: Make the surface smooth.

Make the surface smooth.

2/3

STEP 6: The next day use special tools Deco Create速 to create joints horizontally. During the summer you can do it the same day, after some hours.

Also, use special tools Deco Create速 to create joints vertically.

Continue and create the look of brick, covering all the surface.

LESS TIME-LESS COST THAN BRICK

3/3

ROCK-CREATE APPLICATION

STEP 1:

We cut the blocks of polystyrene and model them in order to achieve shapes, very similar to natural rocks.

The same.

Final shape like a natural stone. We can assemble the blocks using polyurethane foam.

1/5

STEP 2:

We spread the surface, where we will apply Rock Create, with Style Contact.

STEP 3:

We install fiber glass mesh as a reinforcement of the plaster.

STEP 6:

We apply primer Rock Create.

The same.

2/5

The result after the primer Rock Create.

STEP 4:

We apply Rock Create using a plaster sprayer.

We continue.

STEP 5:

We start texturing the surface using Style Beton速 stamps and Style Liquid Release.

3/5

The same.

The result after the texturing.

STEP 6:

We start coloring the surface using Rock Staining with a brush, a sponge or a sprayer.

We continue.

4/5

We continue.

We color the surface using Rock Staining with a brush, a sponge or a sprayer, until the wanted result.

5/5