Stromsholm Let's Get Gluing

By Appointment to Her Majesty The Queen Suppliers of Horseshoes

Hoofcare and Soundness

LET'S GET GLUING

TM

www.stromsholm.co.uk

Let's get gluing

CONTENT PAGE How to Guide - Vettec

Let's Get Gluing Technical information Safety information Quick quiz Introduction to Vettec

4 17 20 24

Product Range Vettec Glue Shoes Imprint Shoes Pro-Glu Equilox / Jameg Hoofcast Hoofcare & Soundness

2

T: 01908 233909

www.stromsholm.co.uk

30 32 36 40

How to Guides 26 57 60 62 63 64 68

Guide to Vettec Bovi-Bond Introduction to Bovi-Bond Bovi-Bond Block How to apply Bovi-Bond Block

Equi-Pak Super-Fast Adhere Sole-Guard

74 75 78

Pro-glue Sole Fill Hoof Casting Iron Block Yellow Shoe Imprint Shoe Easy Slipper Shoe

42 44 50 52 54

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Let’s Get Gluing

TM

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Stromsholm is delighted to bring you this guide on the different adhesives on the market and especially on how to use the most popular adhesives found in the farriery industry. This booklet would have not been possible without the help and advice from the manufacturers featured in this ‘let’s get gluing’ guide and especially to Jeff Newman for sharing his technical data with Stromsholm.

Many farriers worldwide have never needed to use adhesives, some farriers have tried to use adhesives but without much success, often due to lack of training.

But more and more farriers continue to use adhesives and modern materials in their everyday work.

For these farriers, having these products in their toolbox often gives them more options with dealing with problem feet, often they are both easier / quicker options and also more profitable options for their business.

Stromsholm hopes this guide will give farriers a better understanding of the different adhesive families in general and more specific information about the adhesive used in farriery.

We shall also give comprehensive advice on the correct use of these adhesives, to ensure farriers get the best results from day one when using these products.

So, Let’s Get GlueingTM.

3

Let's get gluing The two adhesive families most common in farriery are urethanes for example Vettec and acrylics, for example Pro-Glue.

BY ROYAL KERCKHAERT

But before we focus on these products, lets look at the other types of glue on the market and how they work.

Chemically Curing

Chemically curing adhesives are reactive materials that require chemical reaction to convert them from liquid (or thermoplastic) to solid.

Once cured, these adhesives generally provide high strength, flexible to rigid bond lines that resist temperature, humidity, and many chemicals. They may be classified into two groups:

4

Single Component (1-C) Anaerobic Cyanoacrylates Heat Cure Moisture Cure Radiation Care Silicones

T: 01908 233909

Two Component (2-C) Epoxies Methyl Methacrylates Silicone Adhesives Urethanes

www.stromsholm.co.uk

Take home message Adhesives are generally either 1 or 2 parts.

Cars have approx. 20kg of adhesives.

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Single Component (1-C)

1. Anaerobic

2. Cyanoacrylates

3. Heat Cure - Epoxy Resin – STROMSHOLM –

HOOFCARE& SOUNDNESS

•

•

•

•

Components are premixed in their final proportions.

They are however chemically blocked.

A s long as they are not subjected to the specific conditions which activate the hardener they will not bond.

They require either high temperature or substances or media (light, humidity) from the surroundings to initiate the curing mechanism.

The containers in which this type of adhesive are transported and sorted must be carefully chosen to prevent any undesired reactions.

• • • • • • •

Cure under the absence of oxygen Half filled air-permeable plastic bottles High strength and high resistance to heat Very brittle and are not suitable for flexible substrates Maximum gap approx.

0.1 mm Resistant to oils, solvents and moisture Used for bearings and electric motors

• •

• •

•

“instant” bonding to most surfaces.

They are used for a wide range of industrial applications as well as the ever-popular Super Glue and Krazy Glue® Bonds to skin !

They are thermoplastic when cured and consequently are limited in temperature capability and chemical resistance.

Medical technology, e.g. as a textile adhesive and for spray-on bandages.

•

• •

• •

Most widely used raw material for formulating heat curing one component adhesives.

Automotive industry, aerospace industry, and metal fabrication sector.

Microelectronics, they are used with silver powder added as electrically conducting adhesives.

Heat-conducting properties.

Cured adhesives are hard and rigid but tough with excellent chemical and heat resistance.

5

Let's get gluing 4. Phenol-formaldehyde Resins

5. Polyurethane

6. Moisture Cure

7. Radiation Cure

• • •

• •

• •

6

Phenolic resins cure at 100 – 140c.

During the sure, water is liberated from the adhesive. The liberated water is present in gaseous form.

To avoid foaming they are cured under pressure.

Pure phenolic resins are very brittle and sensitive to peel stress. Additives increase elasticity.

Good temperature stability.

Resistance to water weathering (boat adhesives) and brake and clutch linings in vehicles.

•

• • • • •

• •

Cured between 100 - 200c Bonds formed with heat cured polyurethane Adhesives are generally tough and hard with high strength but are still elastic.

Automotive industry Cardboard boxes

T: 01908 233909

• •

Require moisture to trigger the curing reaction.

Range from hard and rigid to soft and flexible depending on formulation.

Windshields in automobiles, windows in aluminium ship structure.

Combined with polyurethane hot melts the initial strength of hot melts to improve heat resistance of moisture cured adhesives.

www.stromsholm.co.uk

•

•

•

Cure during the time they are exposed to radiation.

One of the substrates must be permeable to the specific wavelengths of light that initiate the cure of the adhesive.

The curing process for these adhesive does not merely depend on the wavelength of the light, optimum cure also depends on the dose of radiation used and thickness of the bond line.

Used for joining transparent plastics and as a liquid seal for metal/ plastic casings.

Increasingly used in dental technology

– STROMSHOLM –

HOOFCARE& SOUNDNESS

8. Silicones

• •

•

Single component silicones cure by exposure to moisture/air.

They are well known as adhesive/caulks sold in a many colours for household use.

There are a variety of formulations available for industrial applications for bonding and sealing glass and metal.

Take home message 1 part adhesives need specific additional environment to cure.

– STROMSHOLM –

HOOFCARE& SOUNDNESS

The earliest human use of adhesive-like substances was approximately 200,000 years ago, when Neanderthals produced tar from the dry distillation of birch bark for use in binding stone tools to wooden handles. The first references to adhesives in literature appeared in approximately 2000 BC. Adhesive - Wikipedia

7

Let's get gluing Two-Component (2-C)

Epoxies •

•

• • •

•

8

They are supplied as “resin” and “hardener” in separate containers Follow manufactures prescribed ratio of the resin and hardener Mixed together to form the adhesive a short time before application noting cure times / temperature Since the reaction typically begins immediately upon mixing the two components, the viscosity of the mixed adhesive increases with

•

• • •

time until the adhesive can no longer be applied to the substrate or bond strength is decreased due to diminished wetting of the substrate.

Formulations are available with a variety of cure speeds providing various working times (worklife) after mixing and rates of strength buildup after bonding. Final strength is reached in minutes to weeks after bonding depending on the formulation.

Adhesive must be cleaned from mixing and application equipment before cured Applied by trowel, bead or ribbon, spray, or roller.

Use heat to accelerate the cure time.

Two component adhesives are typically tough and rigid with good temperature and chemical resistance.

T: 01908 233909

•

•

•

•

Two component epoxy resin based systems are the most widely used structural adhesives.

They can be formulated into fast curing systems with 2 to 5 minute work life that give rigid bond lines which are somewhat brittle.

Longer work life systems usually contain additives to provide flexible or tough bond lines.

Two component epoxy adhesives are used to bond metal, plastic, fibre reinforced plastic (FRP), glass, and some rubbers.

www.stromsholm.co.uk

Methyl Methacrylates

•

• •

Methyl methacrylate (MMA) can provide faster strength build-up than epoxy adhesives.

Tolerant of oil on the substrate.

Bonds to variety of substrates automotive & railway industry.

Take home message MMA/Acrylic/Methyl Methacrylate can be hand mixed and substrates (fibre glass chop) added

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Reinforcing Strand

Silicone Adhesives

Urethanes – STROMSHOLM –

HOOFCARE& SOUNDNESS

• 3mm chopped strands are especially usefully when being used close to finish surface, due to small stand size finish surface can be sanded to reasonable finish.

AVAILABLE SIZES 500g

The History of Adhesives https://www.adhesives.org/ resources/knowledge-center/ aggregate-single/the-historyof-adhesives

• • • • • • •

•

Production line assembly - electronics and the electrical industry Production of household appliances Automotive industry Cured properties are similar to single component moisture curing silicones.

Two component silicones are used instead of single component silicones when adhesive film thicknesses of over 0.25 inches (6 mm) are required or for large bonding areas.

This type of silicone adhesive is also used when the available humidity in the air does not suffice for the complete curing of single component silicone.

•

Formulated with a wide range of cured properties ranging from soft and flexible, to tough and elastic, to hard and rigid.

Must be “folded” together in a mixing nozzle They are used to bond materials with different flexibility or different thermal coefficients of expansion including glass to metal, fibre reinforced plastic (FRP) to metal, and aluminium to steel.

PU and MMA can both be mixed with mixer nozzles but only PU need to be Take home message Polyurethane must be mixed/folded with a nozzle.

PTFE (plastic tape for engineers) is polytetrafluoroethylene.

9

Let's get gluing Surface Treatment

Youngs Law Contact Anlge Liquid

IMPROVING THE BONDING PROPERTIES OF SUBSTRATES From the foregoing discussion of fundamental bonding mechanisms, it is clear that certain requirements have to be met by the structure of the substrate if a high-quality, strong bond is to be achieved: 1. The substrate surface must have good wetting properties, namely the chosen adhesive should not form beads on the substrate surface but must rather distribute itself (spread) across the surface.

2. The substrate surface must have good bonding properties, namely there must be intermolecular and chemical interactions with the adhesive molecules.

10

3. The surface layer of the substrate must be securely attached to the substrate.

Imagine for example highly rusted steel supports that have to be bonded together.

If the surface rust layer is not removed, then rust is merely bonded to rust. On subjecting the substrates to loads, the rust breaks away together with the adhesive. In contrast to rust, the oxide layer on aluminium is very strongly attached to the base material and is a good base surface for adhesion.

Solid adhesive film – if the bond is in a moist environment.

In order to create a bond having good long-term stability, solely grinding the steel surface is inadequate – and in addition suitable measures must be taken to prevent rusting under the adhesive film when using this steel component in a moist environment.

Take home message Surfaces must be clean/ dry / secure. Do not use acetone!

4. After the bonding process, the surface must not change in an uncontrolled way.

Ground steel, for example, rusts – even under the

T: 01908 233909

www.stromsholm.co.uk

This phenomenon, and the concept of contact angle measurement as a means to describe it, is best defined

by Young’s Equation. Simply stated, the phenomenon is the interaction between the forces of cohesion & the forces of adhesion, which determines whether or not a liquid will spread over a surface or “wet it out.” S=Solid L=Liquid Contact Angle

Wetting

S/L

L/L

0o

Complete

Strong

Weak

High

Strong

Weak

Moderate

Weak

Weak

60

About 2 million “cow blocks” are used world wide per year.

o

90o 120 o

Low

Weak

Strong

180 o

None

Weak

Strong

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Surface energy is measured in Dyne Bonding Low Energy Plastics and Elastomers PTFE

15

An example of using various adhesives in one simple product. Addressing the various substrates •

PVC

100

GLASS

•

ALUMINIUM

ABRANDED STEEL

1000 Surface Energy

Dyne, unit of force in the centimetre-gram-second system of physical units, equal to the force that would give a free mass of one gram an acceleration of one centimetre per second per second.

One dyne equals 0.00001 newton.

•

•

Surface energy and surface tension are key measurements for the wet-out of adhesives, inks, and coatings.

Adhesion is the molecular force of attraction between unlike materials.

The strength of attraction is determined by the surface energy of the material. The higher the surface energy, the greater the molecular attraction. The lower the surface energy, the weaker the attractive forces.

Modified acrylic and synthetic adhesives with better flow (or "wet-out") characteristics have been developed to adhere to low surface energy substrate

•

•

Greater molecular attraction results in increased contact between an adhesive and substrate. In other words, on a high surface energy material, the adhesive can flow (or "wet-out") to assure a stronger bond.

Consider an automobile that has not been waxed for a long time. When water contacts the surface, it spreads in large puddles. The unwaxed car surface exhibits high surface energy - the molecular attraction allows the water to flow.

In comparison, water beads up into small spheres on freshly waxed car. It is an example of low surface energy - the liquid (or adhesive) does not flow out. Surface energy is measured by dynes per centimeter. The dyne level is the actual reading of the critical surface tension.

Ensure the glue on shoes you use are NOT coated with a release agent ….these release HOOFCARE& agents areSOUNDNESS usually silicone based …..adhesives will be like water on a waxed car !

– STROMSHOLM –

Take home message Surfaces must be dry/clean/ no residue from release agents or acetone

Acetone Care Acetone can be used as a glue remover or as a solvent. It can also be used to remove dirt and residue off various surfaces.

AVAILABLE SIZES 50 ML

About 10% of all adheisves production is used in the car industry

11

Let's get gluing Adhesive failures

Adhesive testing • Tensile Strength The tensile strength is on the basis of thread connection strength and includes yield strength, rupture strength, and slippage strength.

• Shear Pure shear stresses are those which are imposed parallel to the bond and in its plane • Peel tests Peel tests are used to assess bond quality since the predominant stress, as the name suggests, is peel or tension. Thus, they are extremely useful in assessing the effects of process (e.g. surface treatment) or service (environmental exposure) on the strength of the adhesive adherend interface. Peel testing requires at least one flexible adherend. The term ‘flexible’ refers to the ability of the adherend to bend through 90° without breaking or cracking.

12

• Cleavage tests Cleavage stresses (essentially concentrated tensile stresses applied perpendicular to the bond-line) are generally undesirable as adhesive joints have poor resistance to cleavage. Cleavage stresses occur as a result of forces being applied to one end of a rigid bonded assembly to force (or pry) the adherends apart (Petrie, 2007) Tensile Tensile-shear Cleavage (thick sections) Peel (thin sections)

•

•

•

Adhesion failure is when glue remains on one of the substrates but not on the other. Causes can be poor cleaning or residue from manufacture i.e. a silicone release agent from injection moulding Cohesion failure is when the adhesive breaks.

This can be remedied by increasing the strength of the glue.

Substrate failure is when the adhesive is stronger than the substrates Remedied by increasing the strength of the substrate

Take home message Examine lost shoes to see where adhesion has failed: is glue still on the foot, still on the shoe or equally on both?

Torsion

T: 01908 233909

www.stromsholm.co.uk

World demand for adhesives & sealants exceeds 20 million metric tons in 2019

– STROMSHOLM –

HOOFCARE& SOUNDNESS The two adhesive families most common in farriery are urethanes for example Vettec and acrylics, for example Pro-Glu. But before we focus on these products, lets look at the other types of glue on the market and how they work.

– STROMSHOLM –

3D

HOOFCARE& SOUNDNESS

HOOfCAST

BY ROYAL KERCKHAERT

Vettec is the market leader thru its most popular products, including SuperFast and Equi-Pak. For more information about Vettec products visit: www.vettec. com. You can also find many instructional videos available on the YouTube channel.

Pro-Glu was developed in the UK by farrier Jeff Newnham.

Pro-Glu is manufactured in the UK especially for farriers and hoofcare practitioners.

You can follow Pro-Glu & Jeff on Facebook, Jeff also does regular online tutorials.

Visit: www.pro-glu.com

Imprint horseshoes invented by Andrew Poynton are the UK’s best-selling glue-on shoe used on laminitis horse & ponies.

Visit: www.imprintshoes.co.uk.

Andrew has trained hundred of farriers in the use of these shoes. Many instructional videos are available online.

Derek Poupard is the farrier behind 3D Hoofcare. Derek was lead farrier for Godolphin Racing and is responsible for developing several unique products for equine hoofcare.

For more information, follow 3D Hoof Care on Facebook, or visit his website at www.hoofcast.com.

13

Let's get gluing KNOW YOUR MATERIALS It is important to know the substrates to which you are adhering, how they must be prepared, the ambient temperature, the adhesive temperature, the substrate temperature and the “open” times of your selected adhesive.

KNOW THE CURE TIMES PART 1 - COLD FOOT - HEATING / COOLING

60

PART 2 - WARM FOOT - HEATING / COOLING

85 80

55 50

75

45

70

40

65

35

60

30

55

25

50

20

45

15

40

10

30

5

20 0

1

2

3

4

SECONDS

5

6

7

0

Test adhesives, feet and shoe hardness with a with a durometer.

14

T: 01908 233909

www.stromsholm.co.uk

50

100

150

200

SECONDS

350

400

450

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Essential tools for consistent results thermometer, moisture meter,gas or blow torch.

Pro-Glu Gas Torch

Pro-Glu Digital Thermometer

Pro-Glu HOOFCARE& SOUNDNESS Moisture Meter

Pro-glu gas torch comes with childproof safety lock. Variable turbo flame adjustment and continuous flame feature with stable safety stand. Easiliy refillable from lighter type propane/butane cartridges.

Easy to use, highly accurate infrared thermometer. Compact, rugged design for drop protection and ergonomic comfort. High contrast backlit display allows good visibility in all light conditions.

Moisture reader used to measure the percentage of water in a given substance. This information can be used to determine if the material is ready for use, unexpectedly wet or dry, or otherwise in need of further inspection.

– STROMSHOLM –

15

Let's get gluing Drying feet Take home message Know the cure temperature and times for each adhesive Halve the temperature = double the cure time.

3 grams of adhesive hold a weight of 17.5 tons https://www.deloadhesives.com/en/news/ industries/cross-industrial-information/ the-worlds-strongest-adhesive/ BUT BEFORE WE START, is it enough to simply just

16

T: 01908 233909

www.stromsholm.co.uk

Disposable Gloves

Ansell Hyflex Gloves

Skytec Ohio Gloves

Wear gloves, Ensure good ventilation, Record your cpd points !!!

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Safety – understanding MSDS & labels – STROMSHOLM –

SECTION 1: Identification of the substance/ mixture and of the company/ undertaking SECTION 2: Hazards identification SECTION 3: Composition/information on ingredients

HOOFCARE& SOUNDNESS

SECTION 9: Physical & chemical properties SECTION 10: Stability and reactivity SECTION 11: Toxicological information SECTION 12: Ecological information

SECTION 4: First aid measures

SECTION 13: Disposal considerations

SECTION 5: Firefighting measures

SECTION 14: Transport information

SECTION 6: Accidental release measures

SECTION 15: Regulatory information

SECTION 7: Handling and storage

SECTION 16: Other information

SECTION 8: Exposure controls/personal protection

Take home message MSDS are for your safety – READ THEM

17

Let's get gluing Material Safety Data Sheets

Pro-Glue Ltd.

Date of issue: 8th May 2014

Material Safety Data Sheets

Rev.No.02

1. Product – Powder Free Textured Blue Soft Nitrile Examination Glove, GM004* 2. Material – Synthetic Nitrile 3. Inspection Parameters

6. Physical Properties Parameters

Before Aging

After Aging (70 = 2C for 7 days)

Inspection Level

AQL

Standard

Median force at break (Newton)

Min 6.0

Min 6.0

Dimension

S-2

4.0

EN455-2

Tensile Strength (MPa)

Min 14.0

Min 14.0

Physical Properties

S-2

4.0

EN455-2

Ultimate Elongation

Min 500

Min 400

Water Tight Test 1,000ml

G-1

1.5

EN455-1

Visual Defects

G-1

2.5

In-house

Criteria

4. Dimension Dimension

Size (MM) XS

S

M

L

XL

Palm Width

75 = 5

80 = 10

95 = 10

110 = 10

=110

Length

= 240

= 240

= 240

= 240

= 240

7. Powder Residue – Maximum 2.0mg / glove 8. Cuff – Beaded 9. Design – Ambidextrous 10. Surface – Microroughened 11. Colour – Blue 12. Q uality Assurance – Manufactured under ISO 9001:2008 and ISO 13485:2003 The data above represents the product norm, which may be changed without notice.

5. Thickness Point of Thickness Measurement

18

Single Wall (mm)

Cuff (at 40mm from the beaded end)

0.09 = 0.03

Palm (at centre of palm)

0.13 = 0.03

Fingertip (at 15mm from the tip of centre finger)

0.14 = 0.03

T: 01908 233909

Pro-Glue Ltd.

Unit 4a, Beaconsfield Road, Bexhill on Sea, East Sussex, TN40 2BN, UK www.pro-glu.com jeff@pro-glu.com (44) 01424210516 (44) 07715273589 VAT 284 2050 18

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

ECHA

What makes UFI so unique?

• Creating a ‘unique formula identifier’ requires:

– STROMSHOLM –

Formulation specific; not unique

EUROPEAN CHEMICALS AGENCY What is a UFI? Using the UFI for your products and mixtures

Submission of harmonised information according to Annex VIII to the CLP • • • • • • •

Full chemical composition Toxicological information Label elements Product category (from EuPCS) Details of product (trade name…)

Additional details (packaging, colour…)

Unique Formula Identifier (UFI)

HOOFCARE& Company SOUNDNESS specific; unique and (generally) not confidential

‘formNb*’ & ‘VAT* number’ • • •

Unique VAT avoid duplication of UFIs generated by different companies resulting from same formulation number. ’VAT 1’ & ’formNb 1’ will always give ’UFI 1’ * formulation number & value added tax number.

UFI for poison centres • • • •

UFI used with other information e.g. trade name or product category.

Rapidly identify the exact product involved in an incident.

Distinguish between two mixtures with the same trade name.

Confirm that the product was correctly identified.

19

Let's get gluing

Quick – Quiz 1) M MA/Acrylic/Methyl Methacrylate can be substrates (fibre glass chop) added.

2) Casting tape is a

mixed and .

3) The 4 basic tests for adhesives are

,

,

4) T he 3 basic adhesive failures are

,

5) Surface energy is measured in

.

6) T he higher the surface energy the

the bond.

7) 20

and and

. .

is the molecular force of attraction between unlike materials.

T: 01908 233909

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

HOOFCARE& SOUNDNESS

8) E quilox, Jameg and Pro-Glu A9020 are all _ adhesives Vettec & Pro-Glu U6020 are both

adhesives.

9) Polyurethane must be mixed/folded with a

.

10) 1 part adhesives need specific additional 11) Remove dust and grease with

to cure. not

!

12) T he substrate surface must be securely attached and free from ______ or particles.

13) Substrates must have good

&

properties.

6) Better. 7) Adhesion. 8) MMA/Acrylic, PU/Urethane. 9) Nozzle. 10) Environment. 11) Isopropyl, Acetone. 12) Loose, Dirt. 13) Wetting, Bonding.

Answers: 1) Hand. 2) 1-Part Moisture Cure. 3) Tensile, Peel, Shear, Cleavage. 4) Adhesion, Cohesion, Substrate failure. 5) Dyne.

21

Let's get gluing

Glueing for Profit Throughout their lives horses will require a variety of hoof care. As a foal this may be as simple as trimming but may also include applying “cuffs” or “extensions”.

Being confident and competent with all aspects of adhesives and composite materials will enable you to deal effectively with a wide range of hoof problems.

When “in work” they may be sound barefoot or, when ridden, in boots.

Sometimes they may need additional protection by means of nailed on metal/ composite shoes. When nailing is difficult, or when the animal has existing trauma to the foot making nailing undesirable, sole protection and / or shoes can be applied using a variety of materials and adhesives.

The emerging market of horse-owners will have seen on social media the use of adhesives and glue-on shoes. They will expect you to be able to provide this service.

££$$…

22

Do you want to offer a complete range of services, is it important ?

Be willing to invest in new products and “bench-test” them at home in the same way you invest time and money on steel/gas/coke to develop forging skills.

Stay at the forefront of new products and techniques.

T: 01908 233909

Take home message • Practice at home • Invest in new products • Develop new skills

www.stromsholm.co.uk

Superglue was first called Eastman 910 in 1958. It was first used as a medical treatment in the Vietnam War. https://lemelson.mit.edu/Dr Harry Coover

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Let’s Get Gluing

TM

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Useful links: www.vettec.com www.stromsholm.co.uk www.pro-glue.co.uk www.hoofcast.com www.delo-adhesives.com www.advancedadhesives.co.uk www.inprintshoes.co.uk www.adhesives.org www.kulzer-technik.com www.hse.gov.uk Available Brands:

BY ROYAL KERCKHAERT

Stromsholm Online Shop The number of new products related to hoofcare coming to farrier industry at the moment is remarkable, the option available to farriers when dealing with problem hooves continues to grow.

To see all the products available from the leading brands available to farriers today please visit:

www.stromsholm.co.uk

23

Let's get gluing

VET T E C T URN S B LUE

ROYAL BLUE

BY ROYAL KERCKHAERT

24

T: 01908 233909

As of December 23. 2020 Kerckhaert became the new proud owner of the Vettec® product line, the producer of glues and materials for hoof repairs.

With this acquirement we want to guarantee you, as our customer, the best product offer in the market.

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

HOOFCARE& SOUNDNESS

About Vettec

www.vettec.com

Vettec™ has been manufacturing and distributing the highest level of horse hoof care products worldwide for over 15 years. Vettec’s extensive line of hoof related materials allow your hoof care professional to complete hoof repairs and glue on shoes with Adhere, urethane adhesive, as well as create instant horse shoes and foal extensions with Super Fast, equi-thane adhesive.

Vettec™ produces six instant hoof pad materials to promote heel and sole growth, eliminate thrush, protect and support the equine foot, and prevent stone bruising. The wide variety of instant hoof pad materials allows you and your farrier to select the proper material depending on your horse’s hoof. Equi-Pak, Equi-Pak|CS, Equi-Pak|Soft, Sil-Pak and Sole-Guard were all designed to protect and support your horse’s hoof.

25

Let's get gluing Vettec Equi-Pak

Vettec Equi-Pak Soft

Vettec Equi-Pak CS

Vettec Sole-Guard

Bonds directly onto the sole & frog, Equi-Pak is a liquid urethane that sets in 30 seconds. Can be used with or without a pad. Provides support & protection for thin soled, flat-footed horses.

About 2X softer than regular Equi-Pak. Stays soft even in cold temperatures. Strong bond to soles sealing out moisture and debris. Perfect for deep commissures and thin soles.

Infused with copper sulphate to effectively manage mild and moderate cases of thrush.

Can be used as a preventative measure during wet seasons.

Provides durable, shock absorbing support.

Great for providing support for heavy, late term brood mares. Temporary protection for horses transitioning from shoes to barefoot. Can be used as a thin protective layer on the shod foot.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

210cc cartridge

210cc cartridge

210cc cartridge

210cc cartridge

26

T: 01908 233909

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Vettec Sil-Pak

Vettec Super-Fast

Vettec Adhere

Vettec Bovi-Bond HOOFCARE&

Packing material is automatically dispensed under a pad to cushion, seal and protect the equine foot. Liquid formula fills all void areas minimizing debris migration providing a clean sole and eliminating odour.

Ideal for foal extensions and making custom shoes.

Great for building heels, correcting heel angles and medial / lateral extensions.

Good for small hoof repairs.

Fast-setting urethane adhesive designed to bond steel, aluminium and urethane shoes to the hoof and to fabricate large and small hoof wall repairs.

Bovi-Bond Adhesive is state-of-the-art, fast-setting adhesive used to glue wood or rubber hoof blocks to bovine hooves. Bonds quickly and is set in 30 seconds.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

160cc cartridge

210cc cartridge

210cc cartridge

210cc cartridge

– STROMSHOLM –

SOUNDNESS

27

Let's get gluing

Other brands available in stock SHOE JAME

G

GLU

Jameg Shoe Glu is a flexible resin whish when applied correctly becomes part of the hoof; it is the closest thing to a hoof transplant.

It as numerous uses from repairing cracks to full wall reconstruction.

28

Glushu provides the farrier with an amazing tool to get the foot off the ground and add modifications providing support and shock absorption without the extra trauma of hammering and nailing. Glushu provides hoof support, shock absorption and cushion so that your horse can continue to be turned out in comfort during a laminitic episode.

Being stable bound has been proven to exacerbate laminitis due to weight gain and lack of exercise.

T: 01908 233909

www.stromsholm.co.uk

Only Equilox is strong enough to stand up to everyday wear and tear, yet remain flexible for easy filing and shaping — even nailing — to handle all your repair jobs, from patching quarter cracks, to major hoof wall reconstruction.

– STROMSHOLM –

HOOFCARE& SOUNDNESS

OK... So what glue do I use for what?

– STROMSHOLM –

HOOFCARE& SOUNDNESS

The right glue for the right job

Foot repairs Quarter cracks / reinforce wall / stabilise Shoeing direct sole glue (steel & aluminium), glue-on shoes (spectra cloth cuff & urethane cuff) Reinforcing sole increasing sole depth

Loctite cyanoacrylate adhesive broke the Guinness World Record by lifting a car weighing more than 5 tons with just 9 drops of adhesive.

Take home message Urethane needs 3-4 mm to cure DO NOT USE ON SPECTRA CLOTH CUFFS

29

Let's get gluing

Equi-Pak – Standard Application 1

This revolutionary soft instant pad material is dispensed onto the frog and sole and gels in 30 seconds.

Equi-Pak sticks directly to the sole and will stay in place throughout the normal shoeing cycle. This material protects, supports, and provides comfort to sore footed horses.

30

Equi-Pak is best applied to a freshly prepared sole and frog.

Remove only the sole that is due to exfoliate soon. DO NOT over-pare the sole.

With all applications make sure the sulcus of the frog is clean and void of any debris.

Be certain no anaerobic bacteria is present.

T: 01908 233909

www.stromsholm.co.uk

2

Place mesh between shoe and hoof.

After shoe and mesh are in place; dry thoroughly.

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

HOOFCARE& SOUNDNESS

3

Immediately dispense onto hoof after drying. DO NOT give sole time to rehydrate.

Fill Equi-Pak just to shoe level. Used for cushion and protection. Seat out shoe so material can “lock” underneath the shoe.

Ground Level Application Excellent for thin soled horses, horses with low heel angles and those with thin walls. The extra support takes stress off the wall and allows the wall to grow down faster and thicker.

1

2

3

If filling with Equi-Pak for full support, use the Adhesive Foam Boards.

Place foam board on shoe and let horse bear weight on it for a few seconds to seal it around the shoe.

Insert tip towards toe and back fill to the bulbs.

This will seal out any moisture or debris.

NOTE: For egg bar shoes, punch a hole in the foam board near apex of frog and fill.

Equi-Pak filled for full support using the Adhesive Foam Boards.

NOTE: If filled to ground level and working on grass use studs or caulks.

31

Let's get gluing

Super-Fast – Temporary Shoes 1

This 30 second set hoof adhesive can be used for small repairs, leveling feet, building heel angles, making custom shoes and foal extensions.

32

Foot prep is key to success here.

Remove all loose, flaky sole and wall. Any separation at the white line must also be removed.

T: 01908 233909

www.stromsholm.co.uk

2

No matter what part of the country you’re in or the condition of the hoof, DRY IT! There’s moisture present and moisture will prevent Super Fast from sticking to the hoof.

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

HOOFCARE& SOUNDNESS

3

Start at one heel and run a bead around the entire ground surface of the hoof. If you have a low spot, you can come back and add before you set the foot down or later on.

4

5

After applying, hold the hoof up for 2 1/2 minutes. Start timing after the material has reached the second heel (not at the start of application).

After 2 1/2 minutes try to move the material at the heels & if the bulbs move instead, the material has cured & the foot can be put down.

After application and final set, rasp to shape and balance.

NOTE: If the horse will be ridden, it is advisable to add a layer onto the outer wall. This layer bonds the ground layer to the outer wall providing stability.

33

Let's get gluing

Super Fast – Foal Extensions 1

Trim the hoof. Any bacteria around the white line is also removed. You do not want to trap any bacteria and it is a weak spot to adhere to.

2

3

Apply ground layer of Super Fast first. For foals 0-30 days old, do not go heel to heel with the material. Hold foot up for about 2 minutes. Apply second layer if needed.

Be careful not to come too far onto sole with the Super Fast. Use a gloved finger to remove any excess or rasp or hoof knife if material is set.

DRY, DRY, DRY - NOTE: That sole is pared out, and all loose structure is being removed. DO NOT over-pare the sole.

34

T: 01908 233909

After ground layer is set, rasp level and check for proper balance.

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

HOOFCARE& SOUNDNESS

4

To apply the lateral extension, stand foal on plastic, foam board or paper. Apply Super Fast outward and up onto the wall to achieve desired support.

Apply layers as needed. DO NOT apply too thick at once as heat on foals may be too much.

Foal Toe Extensions

5

Solar view of ground layer and 3 lateral layers applied.

Finished Product: Foal was turned out 24/7 in mountain pasture with mare.

Stayed on 7 weeks.

NOTE: Monitor and adjust as needed.

Foot prep the same as for lateral extension.

1. Apply ground layer first.

2. Add Super Fast to toe to desired length.

Rasp toe extension back until heel comes off the ground. If the heel touches the ground you might have too much leverage at the toe.

35

Let's get gluing

Adhere – Hoof Repair

This hoof adhesive is used for hoof wall repairs, building heel angles, and gluing on steel, aluminum, and polyurethane shoes. Adhere provides ample working time but is weight bearing in just four to five minutes.

36

1

2

Prepare Hoof - Use a knife, nippers, rasp, or Dremel® tool to remove all weak or flaky hoof wall. If hoof has been treated with oily treatments or ointments, use a clean towel dampened with Denatured Alcohol. Use it sparingly as any solvent can leave a film if over applied. NEVER USE ACETONE.

Dry the Hoof - dry the prepared area with a heat gun for 40-60 seconds. Even in dry climates, moisture is released when any hoof structure is removed. NOTE: Repairs can be done with or without a shoe in place. If repairing after the shoe is tacked on, avoid bonding to both hoof and shoe by placing a piece of duct tape on the foot side of the shoe.

T: 01908 233909

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

HOOFCARE& SOUNDNESS

3

First Layer - Immediately after drying, place mix tip against prepared area and dispense a 1/8” to 1/4” layer using small circular motions. Adhere will set hard to the touch in 45-60 seconds. Final cure is approximately 6-8 minutes.

4

5

Second Layer - Use a clean wire brush to remove gloss on first layer and dry repair area again. Apply second layer to overfill beyond prepped area.

NOTE: DO NOT “play” with the material, mold, or “feather” it. A minimum thickness of 1/8” is required for best strength, & faster set.

Rasp to Dress - Once heat has dissipated from Adhere, it can be rasped and shaped. For show ring, material can be rasped thin, though best results and longevity are obtained when material is left at least 1/8” thick.

37

Let's get gluing

Using Diamond Double Dispenser 210cc for Vettec 210cc cartridges

6 1) Load cartridge into dispensing gun

After finishing, nail and clinch. Adhere takes a nail and clinches similar to natural hoof wall. If clinching near the border of a repair, hammer clinch to avoid putting stress on repair material at its border.

NOTE: Adhere bonds to itself; additional layers can be added after the material is fully cured (6-8 minutes).

38

2) Unscrew locking collar and remove green plug, place aside for future use. 3) Equalize cartridge

T: 01908 233909

www.stromsholm.co.uk

4) Attach mix tip and screw locking collar back on to secure.

(After use, remove locking collar and mix tip. Insert green plug and screw locking collar back in place to preserve remaining material)

LOWER PRICES

– STROMSHOLM –

HOOFCARE& SOUNDNESS

33% BIGGER AND UPTO 20% CHEAPER

BY ROYAL KERCKHAERT

– STROMSHOLM –

HOOFCARE& SOUNDNESS

NEW 210 cc’s

cartridges You asked, we listened. The new Vettec cartridge holds 30% more material a nd is easier to open and dispense. Contact us today and see for yourself why Vettec is still the most trusted brand in hoof care.

– STROMSHOLM –

HOOFCARE& SOUNDNESS 39

Let's get gluing

Sole-Guard – Standard Application 1

Sole-Guard is the first product of its kind to offer fast effective protection and support for the unshod foot. Simply fill the bottom of the foot with Sole-Guard creating a protective coating that bonds to the foot for up to three weeks.

40

Prepare foot as normal with proper trim and balance. Be sure to have the commissures of the frog clean and remove any sole that is ready to exfoliate.

Then DRY thoroughly.

Use heat gun or hair dryer.

T: 01908 233909

www.stromsholm.co.uk

2

With contouring plastic held at the toe, hold hoof up and dispense Sole Guard onto thesole using enough material to cover the entire sole to the white line.

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

HOOFCARE& SOUNDNESS

3

After application, bring plastic back from toe to heel smoothing and pushing material for even fill of sole and frog. Hold foot for 30 seconds. Place foot down on smooth, hard surface.

4

5

Hoof after weight bearing. Note even distribution of material.

Recommended: Do not turn horse out for minimum of 30 min. after application.

Hoof after final set, removal of plastic and trimmed material at the heels and bulbs.

The frog maybe left covered or uncovered.

NOTE: For application on softer surface, please refer to application directions.

41

Let's get gluing

Pro-Glu Sole Fill – Step by step guide 1

To perform a sole glue you will need a dispensing gun, adhesive, optional substrate additives, a tongue depressor and a mixing palate/cup.

42

2

3

4

Ensure both parts are being dispensed. Keep the 2-parts of the adhesive separate.

Dispense the same amount of additive as the activator (black) and mix in with the white part using a tongue depressor. When thoroughly mixed add in the activator (black part).

Continue mixing until all components are thoroughly mixed together.

T: 01908 233909

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

HOOFCARE& SOUNDNESS

5

6

7

Spread the adhesive and additional substrate mix over the part(s) to be protected. Once cured , remove unwanted material with a rasp and knife.In this demonstration we have only covered the sole area but this technique can be used over the whole (or part) of the sole/ frog and wall.

43

Let's get gluing

Hoof Casting – Step by step guide 1

2

3

Preparation and Glue Application Dress the hoof lightly and apply glue around the hoof with a liberal amount at the heels as these are the anchor points.

6

44

Apply Water Use a sponge and lightly wet the entire cast you have applied. The water and exposure to air are what is needed for casting material to set hard.

T: 01908 233909

7

www.stromsholm.co.uk

8

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

4

Plastic Wrap Plastic wrap the hoof extensively to hold the cast in position until the glue and cast have cured. The cast will start curing after 5 minutes & fully set after 20 minutes & the warmer the weather the faster it will set. Should the cast be dry and not fully set then sponge with water again & wrap until it cures.

HOOFCARE& SOUNDNESS

5

9

Applying the Cast

Once your glue is applied start wrapping your cast around the hoof. In order to have wider quarters for nailing and not create a longer toe, I normally double back on my casting at the quarter. Do a full wrap every 2-3 turns to hold the cast in place.

10

Remove Heel Section It is important to remove this heel section as it will constrict normal hoof movement. If you have to leave it in, please ensure it is less than 3 layers thick and does not stay full for more than 10 days.

If your horse is confined than the full shoeing period is fine.

45

Let's get gluing

Hoof Casting – Step by step guide

46

11

12

13

15

16

17

T: 01908 233909

www.stromsholm.co.uk

14

Nailing Nail to the cast as if you have a thick walled horse. You do not need to block your nails or undercut your clinches as the material accepts the bedded clinch very nicely

– STROMSHOLM –

HOOFCARE& SOUNDNESS

The Answers You Need - Derek Poupard – STROMSHOLM –

HOOFCARE& SOUNDNESS

Why should I cast my horse?

Is it suitable for stabilising a hoof wall crack?

What size should I use, 2" 3" or 4"?

Do I need to prepare the hoof for gluing the cast?

After 35 years of shoeing and gluing horses I have found this to be the most efficient way of protecting and aiding a compromised foot. A shoe can be nailed to a cast very easily as in effect you are creating a thicker wall that absorbs and distributes force. This thicker wall can be nailed to without the risk of close nails.

I have found this to be the moss effective crack repair to date. The video on this site will give you an insight into stabling the crack. The other alternatives of screws, wires and braces can be risky if there is no wall thickness to work with. As long as an interface is placed over the crack itself then there is very little risk involved.

I generally use a 2" cast for wall rebuild on a racehorse with a size 4 - 7 race plate.

I do not recommend stripping the dorsal wall or roughening it to apply a cast as this removes all the natural hoof varnish and will weaken and soften the wall. A light sanding is all it needs, especially at the anchor points at the heels. This way when the cast is ready to be replaced or removed it will come off easier with little damage to the wall. The shape of the cast when applied will hold it in place as well as the small amount of glue needed.

If it's a larger foot or I also want to cover the sole, I would opt for the 3". The 4" is used for very large feet or to apply a clog.

When do you use a full pad cast versus a wall only cast?

If I am presented with a bruised foot or suspected corn then I will use a full pad with a medicated osmotic gel. This will protect the foot from further injury and basically float the sole of the hoof within the cast giving it time to heal while still exercising or racing. I use a wall only cast on the hoof wall that in the past I would have applied a glue on shoe. By casting, I am creating a new thick wall that accepts nails with little risk and gives me a good few cycles of shoeing to nail to.

47

Let's get gluing Pro-Glu Moisture Meter

Pro-Glu Brush

Pro-Glu Gas Torch

Pro-Glu Digital Thermometer

Use a moisture meter to check moisture is zero.

Use a wire brush to remove all loose substrate from surfaces to be glued.

Use a gas torch to dry all glueing surfaces.

Use a thermometer to check ambient, glue and substrate temperatures

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

ONE SIZE

ONE SIZE

ONE SIZE

ONE SIZE

48

T: 01908 233909

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Iron Block Yellow Shoe

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Size 00 0 1 2 3

110 PAIRS PAIRS

ININONE ONEPACKAGE PACKAGE

3/8 3/8

THREAD THREAD

• • • •

Size as per Kerckhaert DF. Rubber-coated high-quality aluminium shoe Good for captives and broken hooves.

Fits like a protective collar around wall of the hoof and the sole.

AVAILABLE SIZES 00, 0, 1, 2 & 3

49

Let's get gluing

Iron Block Yellow Shoe – How to guide 1

2

Rasp hoof wall & bevel distal border

Clean and dry

7

8

Dispense adhesive onto sole surface of the shoe

50

T: 01908 233909

www.stromsholm.co.uk

9

Fill any gaps

Fill cuff / wall void via holes

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

3

Check fit – especially the toe clips

4

Cut off toe clips if needed

HOOFCARE& SOUNDNESS

5

6

Gas torch surface Lightly burnglueing off plastic residue

Ensure glue is free flowing

10

Remove excess adhesive with rasp

51

Let's get gluing

5 Minute – Fitting guide A • Match shoe size to hoof.

C

B • Place shoe in container on shoe support.

• Whilst shoe is heating.

Bevel edge of hoof wall.

• Add Imprint Hoof Repair material if required.

• Create 6-8 crisp keying points around the lower edge of hoof wall.

• Add boiling water… 100c to cover rim only.

• Heat until malleable – approx. 2 minutes.

• 8 or 10mm diameter and 2/3 depth of hoof wall.

2 Minutes Approx time required

52

Shoe Temperature = Malleability

T: 01908 233909

www.stromsholm.co.uk

D • Apply Imprint adhesive to hoof wall to height of shoe rim.

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

HOOFCARE& SOUNDNESS

E • Remove shoe from container wearing wet latex gloves.

• Shake off excess water.

G

F

H

• Position and mould shoe centrally on foot.

• Harden with Imprint Freezer.

• Run a bead of adhesive around rim.

• Quickly blend rim to hoof wall.

• The shoe should be hard before weight-bearing.

• Let horse stand until adhesive is hard.

• If required, add extra Imprint Hoof Repair to frog plate to ensure ample contact with frog.

• Maintain original rim height.

• Run a wet finger around rim to open out a little.

• Ensure good frog contact.

• Minor finishing can be done with a rasp to smooth edges.

• Press plastic into indentations.

• Any area needing remodelling can be reheated using a small flame torch.

• Blend heels of shoe to hoof.

1 Minute

2 Minutes Shoe Temperature = Malleability

53

Let's get gluing

Easy Slipper Shoe – How to guide When applying Easy’s Slipper®, it is important to take into account the environmental factors (e.g. humidity, temperature, etc) for proper glue application and bonding. Please follow the glue manufacturer suggested conditions for optimal application temperatures and conditions.

Easy’s Slipper® should ONLY be applied after cleaning and trimming the hooves.

Application instructions 1) M ake sure the hoof wall is clean. Rough up the hoof wall by rasping and sanding. Use 60 grit or rougher sand paper. You may prefer to use your electric buffy.

2) It is CRITICAL to check the moisture in the hoof where the cuff will cover with a moisture meter.

If the moisture reading is greater than zero, go around the hoof wall with a mini torch and recheck the moisture reading. Typically, the hoof will reach a moisture reading of zero after two or three passes with the torch. Between passes, use a wire brush to scuff up the hoof wall.

3) At this point, put on latex gloves as the procedure above removed any oils that might have been on the hoof wall. Clean the inside of the slipper with denatured alcohol. (Use acetone if using Equilox glue). Do not use the mini torch on the inside cuff of the slipper.

4) D ry fit the slipper. Visually it is easy to check the appropriate length. To check the width,

54

T: 01908 233909

www.stromsholm.co.uk

move the slipper from left to right. There should be little if any movement. Let your horse walk up and down the shed row prior to preparing for gluing. Lift the hoof.

5) P repare the glue. Most glue has an optimal temperature for use around 72 degrees.

Either warm the glue with hot water or cool it with cold water.

6) P URGE THE GLUE prior to putting on a mixing tip. When material comes out of both sides equally (sometimes 3-4 pumps of the gun), you can place the mixing tip on the tube.THIS STEP IS CRITICAL FOR A PROPER BOND.

1

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

2

3

4

7) Have an assistant pick up the opposite hoof so that the horse is bearing its weight on the hoof you are gluing. Keep a hoof knife in your hand, while gluing, to pull the slipper away from the hoof wall in case of inadequate glue coverage. Go around the slipper and insert the glue in the pre-drilled holes and begin the gluing process. The dispersion of glue can be seen through the slipper. It is essential to get as close to 100% glue coverage on the cuff as possible.

Move quickly as most glues setup within 30 seconds. Change tips often. Use at least two tips per slipper. (After you have mastered gluing you’ll us less!) Have extra tips available in case the glue starts to setup within the mixing nozzle. You will know because it will become harder to dispense the glue. If any part of the glue starts to come out the back of either side of the tube, stop and replace the glue with another tube as the mixing ratio will be changed and the glue bond will be compromised. After the glue has setup, you can place the hoof that was being held back on the ground. Usually within a minute.

HOOFCARE& SOUNDNESS

8) R eplace the mixing nozzle and repeat the process on the other hoof.

9) Use a hoof knife and rasp to dress the slipper by removing any excess material.

10) W e recommend filling in under the back bar to prevent debris from collecting under the heal bulbs. HOOF LIFE may be used under the bar for open bottom and heart bar slippers. Regardless of which style of slipper you are using we recommend putting Artimud in the frog grooves to prevent any thrush.

5

55

IT’S ALL IN THE MECHANICS Let's get gluing

Bio-mechanical design and superior material allows:

• • • • •

Breakover Natural flexion Reduction of force Injury support And more

HEART BAR

YEARLING SLIPPERS

MINI TO DRAFT SIZES EASY’S SLIPPER – BETTER SHOE, BETTER HORSE

56

T: 01908 233909

www.stromsholm.co.uk

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Thoroughbred Flat Bottom Slipper

Thoroughbred Rocker Bottom Slipper

Easy Slipper Heart Bar HOOFCARE& Rocker

Developed during 2018 in the UK and USA by experienced thoroughbred farriers and veterinary surgeons.

Developed during 2018 in the UK and USA by experienced thoroughbred farriers and veterinary surgeons.

• • •

• •

Positive frog support that provides therapeutic relief for Laminitis, Navicular, Flat Feet and Quarter Cracks. The rocker allows for the most comfortable position.

•

Lightweight Quick and easy to glue on.

Can be temporarily attached by vet wrap.

Flat or Rocker ground surface.

• •

Durable Perfect for sore footed yearlings.

Protects the sole, frog and wall.

Ideal for use after a punctured sole.

AVAILABLE SIZES

AVAILABLE SIZES

3x0 (41/4) & 2x0 (41/2)

3x0 (41/4) & 2x0 (41/2)

– STROMSHOLM –

SOUNDNESS

AVAILABLE SIZES Size 00 0 1 2 3 4 5 6 7 8

Width 4⅞ 5 5¼ 5½ 6 6⅛ 6⅞ 7⅛ 7½ 7⅞

Length 4¾ 5⅛ 5¼ 5⅜ 5¾ 6⅛ 6⅝ 7⅛ 7⅜ 7⅝

57

Let's get gluing Easyshoe Performance

Easyshoe Sport

Easyshoe Performance Spacer

A wide-webbed shoe with integrated frog support that maintains pressure on and around the frog without hampering heel expansion and contraction. The frog support opens with the growth in the heel area during the trimming cycle.

A wide-webbed shoe that offers maximum support across the sole. The internal metal spine allows the shoe to be adjusted to many hoof shapes and creates additional structural integrity.

Spacers are for use with the EasyShoe Perfomance Nail-on or Glue-on style shoes. Sold as two per pack.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES Size 0 1 2 3 4 5

58

Width 105-111mm 112-119mm 120-127mm 128-135mm 136-143mm 144-152mm

Length 108-115mm 116-123mm 124-131mm 132-140mm 141-149mm 150-159mm

Size 0 0.5 1 1.5 2 2.5 3

T: 01908 233909

Width 100-110mm 105-115mm 110-120mm 115-125mm 120-130mm 125-135mm 130-140mm

Length 114-117mm 118-121mm 122-125mm 126-129mm 130-133mm 134-137mm 138-141mm

www.stromsholm.co.uk

Size 8mm 12mm 14mm 16mm

Quantity 2 2 2 2

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Glushu Front and hind

Dalric Foal Extensions

Dalric Foal Heel Extensions HOOFCARE&

A light, durable shoe with a 6-10 week shoeing cycle allowing the horse to be worked whilst the hoof heals. A urethane cuff bonded to an aluminium plate allows the Glushu to be shaped to the horses hoof.

To correct axial limb malformations.

• Easy to apply (adjustable) • Dramatic results when used early • Enhances dynamic stability • Relieves stress on young bones • Minimizes hoof & joint distortion

Dalric Heel Extensions.

For foals with weak flexors.

Reasons to use: • Prevents heel bruises & abscesses • Establishes proper joint alignment • Prevents crushed heels

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

Front 4x0, 3x0, 00 0 1 2 3 4

Hind 00 0 1 2 3

1 2 3

– STROMSHOLM –

SOUNDNESS

Pair + accessories Pair + accessories Pair + accessories

D1 D2 D3

Pair + accessories Pair + accessories Pair + accessories

59

Let's get gluing Imprint First Oval

Imprint First Round

Imprint First Hind

A completely mouldable, nail-less shoe which matches with the individual shape and contours of a horse’s hoof.

Based on a heart-bar design, the shoe provides maximum support whilst allowing natural hoof movement.

Developed specifically to accommodate the anatomy of the broader, flatter foot.

A stronger frog cradle results in a more supportive shoe for this shape of foot. The seating angle makes it more comfortable for feet with thinner or prolapsed soles.

The hind shoe exhibits all the same qualities as the existing Imprint First shoe but being the correct shape for the hind foot, minimal moulding will be required making it quicker and easier to fit.

AVAILABLE SIZES

AVAILABLE SIZES FRONT

AVAILABLE SIZES HIND

5 x 5" 5¼ x 5¼" 5½ x 5½" 5¾ x 5¾" 6 x 6" 61/2 x 61/2"

4½ x 5" 4¾ x 5¼" 5 x 5½" 5¼ x 5¾" 5½” x 6"

2¾ x 3" 3¼ x 3¾" 3½ x 4" 4¼ x 4¾" 4¾ x 5¼" 5¼ x 5⅞" 5⅞ x 6½"

60

70 x 75mm 82 x 95mm 89 x 100mm 108 x 120mm 122 x 135mm 135 x 150mm 150 x 165mm

T: 01908 233909

127 x 127mm 133 x 133mm 140 x 140mm 146 x 146mm 152 x 152mm 165 x 165mm

www.stromsholm.co.uk

114 x 127mm 120 x 133mm 127 x 140mm 133 x 146mm 140 x 152mm

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Imprint Plus Plastic Shoes

Imprint Sport Horseshoes

Imprint Plus Foot Care Kit HOOFCARE& – STROMSHOLM –

SOUNDNESS

Available with or without stud holes.

A flexible high-tech patented sport shoe used in eventing, showjumping, dressage, endurance and racing.

Imprint Sport provides maximum support yet is as hard- wearing as steel but less than half the weight.

A flexible high-tech patented sport shoe used in eventing, showjumping, dressage, endurance and racing. The ‘W’ flexing bar allows expansion of the heels. Unique composite construction. Ideal for resolving poor quality hoof issues when it’s difficult to nail on a conventional shoe. Available with or without stud holes.

AVAILABLE SIZES

AVAILABLE SIZES FRONT

23/4" 3¼" 3½" 4¼" 4¾" 5¼" 5⅞"

70mm 82mm 89mm 108mm 122mm 135mm 150mm

5" 51/4" 51/2" 53/4" 6" 61/2"

127 x 127mm 133 x 133mm 140 x 140mm 146 x 146mm 152 x 152mm 165 x 165mm

AVAILABLE SIZES HIND 41/2" 43/4" 5" 51/4" 51/2"

114 x 127mm 120 x 133mm 127 x 140mm 133 x 146mm 140 x 152mm

KIT CONTENTS 1 pair of Imprint Plus (size of your choice) 1 Imprint Structural Adhesive inc. 2 nozzles 1 Imprint Dispensing Gun 1 Imprint Hoof Repair – 125ml starter pack 1 Imprint Shoe Freezer 1 pair latex gloves 1 surgical spirit & pump action spray dispenser 1 cleaning brush 1 container (for shoe heating) 1 aluminium-edged locking case Fitting instructions

61

Let's get gluing Pro-Glu A9020 Adhesive

Pro-Glu Adhesive A9020 (small)

Pro-Glu A9040 Adhesive

For cool climate

Imprint Structural Adhesive NEW

For hot climate

When working at 20c

When working at 40c

Open time 60-90 secs, fixture time 90-120 secs. High bond strength, can be mixed with substrate for repairing/ reinforcing hoof wall and sole, for use with spectra cloth/cuffs, urethane glue on shoes/cuffs.

High bond strength, can be mixed with substrate for repairing/reinforcing hoof wall and sole, for use with spectra cloth/cuffs, urethane glue on shoes/ cuffs.

Open time 60-90 secs, fixture time 90-120 secs. High bond strength, can be mixed with substrate for repairing/ reinforcing hoof wall and sole, for use with spectra cloth/cuffs, urethane glue on shoes/cuffs.

Imprint Ultra-fast Structural Adhesive sets in 4 minutes and developed to withstand the extreme environment which horses hooves are often subjected to. Works even where moisture is present.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

400 ML

50 ML

400 ML

50 ML

62

T: 01908 233909

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Equilox 1 & 2 Repair System

Equilox - Single Use System Pot

Jameg Shoe Glu

Jameg Glu Black Dye HOOFCARE&

An extremely strong resin that can be used for anything from repairing small quarter cracks to reconstructing an entire hoof wall, yet flexible enough for easy filing, shaping, & even nailing.

An easy-to-use adhesive.

Used for a range of tasks from shoeing to major repair.

Strong enough for everyday wear and tear, yet flexible for easy filing and shaping from patching quarter cracks.

A flexible resin - when applied correctly becomes part of the hoof. Used for repairing cracks to full wall reconstruction. Sets in minutes. The hoof can be rasped, nailed and trimmed just like natural hoof wall.

Designed to help blend glue with darker hooves. The Black dye is an intense black pigment that is chemically compatible with all commonly available acrylic adhesives used in equine hoof repair.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

420 ML

One size

E1 Sets in 6-8 min

E2 Sets in 4-6 min

Black / White

1oz / 2oz

– STROMSHOLM –

SOUNDNESS

63

Let's get gluing Hoofcast Casting Tape

Hoofcast Nano Tape

Hoofcast Osmotic Gel Kit

Farrier Wrap

Hoofcast casting tape to aide horses with compromised feet. Hoofcast provides protection from wear, helps strengthen & stabilize the hoof capsule & is excellent for therapeutic applications.

Double sided gel tape made of PU gel material with high stickiness, new nano-technology & adaptable material it holds on smooth surfaces.

A poultice for the palmar and plantar (sole) surfaces of the hoof. Contains an osmotic gel saturated hoof dressing impregnated in a surgical grade felt pad cut to size for the hoof.

Developed to provide a thicker & stronger film wrap for use in hoof repair & for gluing on shoes. Easy to apply - will not tear easily, translucent, can be torn by hand, sticks to itself not to the horse.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

2 Inch , 3 Inch & 4 Inch

30mm x 3 meters

Gel - 150 ML

64

T: 01908 233909

www.stromsholm.co.uk

2 Pad included

Single - 100mm x 125m Box - 10 Pcs

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Rubber Powder Mix

Reinforcing Strand

Bond Tech Equine Pad

Diamond HorseHOOFCARE& Silicone

Add 10% to Pro-Glu A9020 for sacrificial sole covering, ideal for sore footed and damaged soles.

3mm chopped strands are especially usefully when being used close to finish surface, due to small stand size finish surface can be sanded to reasonable finish.

Bondtech Hoof Pad medium is designed absorb shock whilst creating a hoof packing. This is a preventative measure for sore feet & can also comfort a sore footed animal.

1 component silicone.

Fungi preventing properties.

Vinegar based, shorter setting time. Nontoxic.

Better for the hoof, better for the horse!

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

5g or 500g

5g or 500g

180 CC - Medium

222 ML

– STROMSHOLM –

SOUNDNESS

65

Let's get gluing Bovi-Bond Wood Blocks

Bovi-Bond Rubber Block

Vettec Equi-Styrofoam

Contouring plastic

Provides protection and comfort for the cow. Better cow posture thanks to the shape of the hoof block.

Suitable for polyurethane or acrylic adhesive. Made from Pine.

Provides superior traction on difficult surfaces.

Supports both heel and toe.

Suitable for polyurethane or acrylic adhesive. Wear resistant.

Seals and supports Vettec products until set.

Recesses material.

From ground level for traction.Reduces the time holding the hoof up.

Translucent lightweight plastic material that can be utilized to push the product into the voids.

Used after applying Vettec products to smooth and level the material.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

ONE SIZE

50 per case

Box of 20 (5.75" x 5)

3000 x 150mm

66

100 pcs per box

T: 01908 233909

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Composite Cloth

Diamond Flex Hoof Wrap

3M Duct Tape

Ian McKinlay Shoe HOOFCARE& Liner

Combine adhesives with composite cloth to create a super strong hoof repair. It is important that the composite cloth is completely covered with the adhesive before application.

Use for wrapping legs, as protection, support etc. Easy fitting, no risk of slipping. Easy to tear, sticks to itself. Allows skin to breathe. Does not stick to hair. Weather resistant.

Super strong and super sticky tape which can be used for a multitude of applications. Save time and hassle of removing sticky or dried-on residue.

The liners are made of soft rubber that fits inside the shoe to prevent glue from entering the sole cavity.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

ONE SIZE

10cm / 4 Inch (W)

50mm X 50m

Box

4.5m / 5 yd (L)

– STROMSHOLM –

SOUNDNESS

20 pieces

67

Let's get gluing Anti Bac Paste

Copper Sulphate

Strong Iodine Spray

Diamond Hoof Putty

Contains a powerful antibacterial combination of Sulphur & Chlorocresol with the natural Eucalyptus oil in a unique pliable, functional, waterproof waxy base/formula.

A powerful disinfectant for use on equine hooves. This helps to prevent hooves becoming soft & crumbly.

Farriers mix the copper sulphate crystals into dental impression materials.

Iodine is used on the hoof for its disinfectant and antiseptic properties. It is designed to treat and prevent fungal & bacterial infections. Also good for hardening the soles of horses with weaker feet.

Hoof putty, ideal for filling old nail holes. Easy to apply and shape for a clean result.

Protects the old nail hole against penetration of moisture and debris. Made out of natural linseed oil.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

250 ML

450 gms

500 ML

Black / Natural

68

T: 01908 233909

www.stromsholm.co.uk

1kg

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Wire Scratch Brush

High Speed Rotary Cutter

3M Sanding Block

Tongue Depressor HOOFCARE&

Light duty scratch wire brush.

Can be used for removing scale from shoes and to clean out hooves.

High speed cutters can be used for shaping, hollowing, grooving, slotting, making tapered holes in soft metals, plastics and woods.

Sanding Block for giving the hoof a pristine finish after shoeing. Made with a superior material.

Standard, economy grade non-sterile tongue depressor.

These flat stir sticks can be used for stirring and mixing glues, chemicals & other industrial liquids. Sticks are economical grade with a flat tip.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

ONE SIZE

ONE SIZE

Piece - 1 Block

Box - 24 Blocks

– STROMSHOLM –

SOUNDNESS

Box

100 pieces

69

Let's get gluing Acetone

Surgical Spirit

Pro-Glu Dispenser Gun

Care Acetone can be used as a glue remover or as a solvent. It can also be used to remove dirt and residue off various surfaces.

Ideal for efficient application no wastage or contamination.

Pump action spray dispenser.

Deluxe dispensing gun has smoother action and greater leverage for cold weather applications.

Automatically kicks back and releases the pressure.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

50 ML

240 ML

ONE SIZE

Ansell Hyflex Gloves

Disposable Gloves

Skytec Ohio Gloves

Nitrile foam gloves for versatile use and wearability.

Combines comfort and dexterity for enhanced protection.

Clear disposable gloves. Suitable for right and lefthand use. Use once and throw away.

A durable glove with excellent flexibility & tactile touch.

Anatomically designed for comfort, dexterity & fit. Resistant to abrasion and tearing.

AVAILABLE SIZES

AVAILABLE SIZES

Med / Large & XL 1 Pair (piece) / 50 Pairs (Box)

Size 7, 8, 9 & 10

AVAILABLE SIZES Size 8 & 9

70

Sold in pairs

T: 01908 233909

www.stromsholm.co.uk

Sold in pairs

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Deluxe dispensing gun has smoother action and greater leverage for cold weather applications.

Automatically kicks back and releases the pressure.

AVAILABLE SIZES

AVAILABLE SIZES

Dispenser for 225ml tube

NEW 210 Dispenser

Imprint Adhesive Gun

Jameg / Equilox Dispenser Gun

For efficiently applying Imprint Structural Adhesive

AVAILABLE SIZES

ONE SIZE

One size

SOUNDNESS

OLD 160 / 180 Dispenser

Dispensing gun designed to fit 420ml Jameg Cartridge.

AVAILABLE SIZES

– STROMSHOLM –

Jameg tip

Sturdy design with high-performance thrust system makes application easier & more economical. Ideal for thicker adhesives & pad materials.

Nozzles DispenserHOOFCARE&

Imprint tip

Diamond Double Dispenser

Diamond tip

Diamond Standard Dispenser

Brand

Application

Diamond

For Vettec 210 CC cartridges

Imprint Mixer nozzles

For Imprint Structural Adhesive 50 ML

Jameg

For Jameg Shu Glu 420 ML

71

Top tips...

Let's get gluing

BY ROYAL KERCKHAERT

&

" Fail to prepare Prepare to fail " let's get gluing

TM

Really...

Come on Jeff, Let’s get Gluing! TM

72

Clean & dry works.

Hot weather sets faster.

T: 01908 233909

www.stromsholm.co.uk

you want to glue on an extension,

right here right now?

Dirty and damp fails.

Cold weather sets slower.

Exclusive online discount Spend

£99

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Spend

£49 – STROMSHOLM –

HOOFCARE& SOUNDNESS

Get

Get

F F O % 10 R WHOLE YOU ORDER + FREE y r e v i l e D

+

Additional

FREE Delive ry

F& nFails 5ors%eshO oes

H over when you spend

£499

Order Online

www.stromsholm.co.uk

73

Let's get gluing

VET T E C T URN S B LUE

ROYAL BLUE Bovi-Bond 210cc is packaged in an industry cartridge and holds 30% more material than prior models, giving you more material for your money.

BY ROYAL KERCKHAERT

74

Bovi-Bond Adhesive is state-of-the-art, fast-setting adhesive used to glue wood or rubber hoof blocks to bovine hooves. Bonds quickly and is set in 30 secs.

T: 01908 233909

www.stromsholm.co.uk

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

HOOFCARE& SOUNDNESS

Bovi-Bond Rubber Block

Bovi-Bond Rubber Block XL

Bovi-Bond Wood Blocks

Provides superior traction on difficult surfaces. Supports both heel and toe.

Suitable for polyurethane or acrylic adhesive.

Wear resistant.

Larger size allows proper fit for larger cows. More sole coverage than traditional block.

Supports both heel & toe. Can be trimmed to smaller size if needed.

Provides protection and comfort for the cow. Better cow posture thanks to the shape of the hoof block.

Suitable for polyurethane or acrylic adhesive.

Made from Pine.

AVAILABLE SIZES

AVAILABLE SIZES

AVAILABLE SIZES

One size

One size

One size

100 pcs per box

75

210 CC’S OF

BIGGER. BETTER. EASIER. Now available @ Stromsholm

76

MORE VALUE FOR YOUR MONEY. 30% MORE. The new VETTEC 210cc cartridge comes in an industry standard cartridge and holds 30% more material than prior models, giving you more material for your money.

Features • • • • •

Benefits

Larger dispensing ports Locking collar holding tip in place After use airtight capping mechanism Durable tube design 210cc volume

Stromsholm

I

• •

No cutting tips or clogged ports Collar locks tip in place and prevents back flow Airtight cap extends into tube and ensures equal flow of both parts Tube design and larger openings prevent back pressure that can break seams More volume per tube

• • •

Wood court, Chesney wold, Milton Keynes, Buckinghamshire, MK6 1NE

T: 01908 233909

I

sales@stromsholm.co.uk

I

www.stromsholm.com

77

Let's get gluing

Bovi-Bond Block – Step by step guide 1

2

Trim and evaluate claws.

Dry, Dry, Dry! 30-45 Seconds.

6

5 6

Claw with block applied. Weight bearing: Bovi-Bond Soft 4 minutes.

78

T: 01908 233909

www.stromsholm.co.uk

Treat affected claw.

– STROMSHOLM –

HOOFCARE& SOUNDNESS

– STROMSHOLM –

3 6

HOOFCARE& SOUNDNESS

4

Apply Bovi-Bond to block immediately after drying.

7

Place block to claw. Thickness of material between block and sole.

Bovi-Bond available at your local stocklist

Block on after 4 weeks.

Cows Feet F1 Cadbury Business Park Ltd, Sparkford, Somerset, BA22 7LH Tel: 01963 824448

Hoof Shop 67 Drumneath Road Banbridge, Co Down, BT32 4HD Tel: 07577654398

Hoof Care Supplies 10 Westfield Road, North Duffield, Selby, North Yorkshire YO8 5TW Tel: 01757 289530

Hooftrimming Ltd Unit 6, Town House Farm Clotton, Tarporley, Cheshire, CW6 0EG Tel: 01829 781476

Atlantic Equine Ltd Unit 5A, Low March Daventry, NN11 4SD Tel: 01327 314880

B D Supplies Tippermallo Road Methven, Perth, PH1 3QL Tel: 01738 842996

79

Let's get gluing Dealer address here

80

Lambourn Race Division

Wood Court, Chesney Wold, Bleak Hall Milton Keynes, Buckinghamshire MK6 1NE Sales: 01908 233909 sales@stromsholm.co.uk

Unit 9, Lowesden Works, Lambourn Woodlands RG17 7RY Sales: 01488 73717 jsuttey@stromsholm.co.uk

Newmarket Race Division

Swan Products (Toddington)

Unit 1, Enterprise Court Studlands Park Avenue, Newmarket CB8 7EP Tel: 01638 665895 newmarket@stromsholm.co.uk

Units 1 & 2 Gamma, Orchard Trading Estate, Toddington, Gloucestershire GL54 5EB Tel: 01242 621590 info@gasforges.co.uk

Maidstone 01622 296481

As one of our valued customers, Stromsholm sends you product, offer and event information. If you no longer wish to receive this please contact us on 01908 233909 or email: sales@stromsholm.co.uk

South East Wales 07837 780509

www.stromsholm.co.uk T: 01908 233909

www.stromsholm.co.uk

Issue 1 - 06/2021

By Appointment to Her Majesty The Queen Suppliers of Horseshoes Strömsholm Milton Keynes

Head Office