08) 2025 SAW Pumps & Plumbing

2025 - Pumps & Plumbing

Pumps & Plumbing

Saltwater Deck Wash Pump Systems

The Deck Wash Pump Systems illustrated below are divided into three typical installations: Simply make a choice of the most suitable Deck Wash Pump , by flow rate and voltage (refer to page 6).

Add a choice of filter and tail kit , applicable to the relevant plumbing system (refer to page 7).

Add a hose coil kit for direct attachment to the pump (refer to page 8) or hose coil and flush link kit (refer to page 10), applicable to the relevant plumbing system.

Add a push timer tap and installation kit (refer to page 12), applicable to the relevant plumbing system.

Add a choice of water pick-up kit (refer to page 13) or water pick-up with dual port live bait pump kit (refer to page 15), applicable to the relevant plumbing system.

All you need to complete the system installation as per the diagrams, is the flexible hose and hose clamps or DMfit® QC Tubing. The necessary connectors are included in the respective kits.

Deck Wash System Diagram - Direct To Pump

Deck Wash System Diagram - Flush Link

Deck Wash System Diagram - Flush Link - Dual Port Live Bait Pump

Shurflo® Deck Wash Pumps

Pumps - Deck Wash - Blaster II - 13.2 L/min

• Ideal for tough washdown applications, such as fish box, scaling, and anchor chain cleaning.

• These rugged self-priming pumps, can run dry without damage, and won’t overheat with extended use.

• Pump must be installed in a DRY location. Do not install pump in wet areas.

• Do not use Teflon tape or sealing compounds on pump threads.

• A filter must be fitted on the inlet side of the pump.

• Mounting screw size Ø 3/16" (4.8mm).

• RCM Certified to Australian Standards. Thermally Protected, CE Certified, Ignition Protected ISO 8846.

Pump - Deck Wash - Pro Blaster™ II - 15.1 L/min

• Shurflo® Pro Blaster Pumps are ideal for washing down the grimiest deck, fish box scaling, and anchor chain cleaning.

• Electro-coated motor, O-ring seal and sealed wire entries enhance corrosion resistance.

• Pump must be installed in a DRY location. Do not install pump in wet areas.

• Do not use Teflon tape or sealing compounds on pump threads.

• A filter must be fitted on the inlet side of the pump.

• Can run dry without damage.

• Mounting screw size Ø 3/16" (4.8mm).

• RCM Certified to Australian Standards. Thermally Protected, CE Certified, Ignition Protected ISO 8846.

Pumps - Deck Wash - Pro Blaster™ II - 18.9 L/min

High Flow

• Shurflo® Pro Blaster Pumps are ideal for washing down the grimiest deck, fish box scaling, and anchor chain cleaning.

• Electro-coated motor, O-ring seal and sealed wire entries enhance corrosion resistance.

• Pump must be installed in a DRY location. Do not install pump in wet areas.

• Do not use Teflon tape or sealing compounds on pump threads.

• A filter must be fitted on the inlet side of the pump.

• Can run dry without damage.

• Mounting screw size Ø 3/16" (4.8mm).

• RCM Certified to Australian Standards. Thermally Protected, CE Certified, Ignition Protected ISO 8846.

Pumps - Deck Wash - Pro Baitmaster™ II Livewell - 15.1 L/min

• The Pro Baitmaster™ II Washdown/Livewell Pumps can be used for washdown or livewell applications and general water transfer.

• The seamless motor shell together with sealed switch and wire entry protects the pump.

• Pump must be installed in a DRY location. Do not install pump in wet areas.

• Do not use Teflon tape or sealing compounds on pump threads.

• A filter must be fitted on the inlet side of the pump.

• Self-priming and can run dry without damage.

• Continuous duty rated, only when used at < 10psi in a livewell application.

• Not suitable for use in a washdown application for more than 20 minutes within an hour.

• RCM Certified to Australian Standards. Thermally Protected, CE Certified, Ignition Protected ISO 8846.

Filter Kits - Deck Wash Inlet

Tubing

239568 Swivel Nut 15mm O.D. DMfit® QC Tubing

• A filter must be fitted on the inlet side of all Shurflo® deck wash pumps to prevent entry of debris to the pump body.

• The filter must be mounted above the waterline to prevent syphoning during cleaning, without closing the inlet valve.

• If DMfit® QC Tubing is used on the inlet, Shurflo® recommends the pump inlet port is plumbed with a minimum of 300mm of flexible PVC pressure hose.

• Swivel nut filters are mounted directly to the pump inlet port.

• Each kit includes - filter, pump inlet and outlet tails or DMfit® connectors where applicable. Other flexible hose and hose clamps or DMfit® QC Tubing is not included.

• 1/2" I.D. flexible PVC hose and 12mm DMfit® QC Tubing plumbing systems are not recommended for use with the Shurflo® ProBlaster 18.9L/min pressure pumps.

Filters - Water Inlet - Small

• Essential requirement on all Shurflo® pressure pumps.

• Fixed mount is fitted remotely from the pump.

• Swivel nut version is fitted directly to pump.

• Compact design.

• Keeps debris out of pump.

• Transparent, easy to see when strainer needs cleaning.

• Stainless steel mesh screen.

• Suits Shurflo's 1/2" NPSM Male Port Pumps.

NOTE: Do not use Teflon thread tape or sealing compound.

Flexible Hose Inlet Adaptor

239580 Flexible Hose Inlet Adaptor suit Shurflo Pump 12mm

239582 Flexible Hose Inlet Adaptor suit Shurflo Pump 15mm

• Shurflo recommends that a short flexible hose be connected directly to the inlet port when using a rigid tubing plumbing system. This minimises noise and vibration.

• Pre-assembled ready for installation.

• 300mm flexible hose length.

• Swivel wingnut tail connects to filter port.

Filters - Water Inlet - Large

23985 Replacement Filter Bowl & Mesh Only

23987 Replacement S/S Mesh Screen

• Designed to keep your bait tank, livewell and washdown pumps protected from harmful debris.

• Mounted remotely from the pump.

• Twist off polyamide bowl and removable stainless steel screen, which allows for easy inspection and cleaning.

• Integral O-ring creates a tight seal, eliminating possible leaks.

23987 23979 / 23986 23985

Swivel Wingnut Hose Tails - Shurflo®

Hose Tails - Nylon - NPT

239568

239564

Deck Wash Hose Coil Kits & Accessories

Deck Wash Hose Coil Kits - Direct Fit to Shurflo® Blaster Pumps

• Ideal to clean hard to reach areas on boats and RVs.

• Can be stored neatly in compact areas.

• Resistant to kinking.

• Maintains coiled shape, even when stretched to maximum length.

• Tested up to 300 PSI.

• Use with 23952 trigger hose nozzle (not included).

• High grade seals and stainless steel spring.

• Non-corrosive and high impact resistance.

• Fully adjustable spray from fine mist to full stream.

• Lock clip for continuous water flow.

• These deck wash hose coil kits are designed to connect directly to the 1/2" NPSM outlet tail on any Shurflo Blaster or Pro Blaster deck wash pump.

• Each kit includes self-coiling flexible hose, trigger style hose nozzle and 23982, 1/2" NPTF x 3/4" GHTM adaptor.

• Relaxn® hose coil kits also include the required snap-on hose connector, 453392

• 3/8" I.D. hose coil kits are not recommended for use with the Shurflo® ProBlaster 18.9L/min deck wash pump.

• Heavy-duty hose ideal to clean hard to reach areas on boats and RVs.

• Can be stored neatly in compact areas.

• Resistant to kinking.

• Maintains coiled shape, even when stretched to maximum length.

• Use with 23952 trigger hose nozzle (not included).

• Swivel wing nut connects directly to the outlet port (1/2"NPSM) on any

• Male GHT thread connects to

or the

or

23741

23743

Hose - Deck Wash - Shurflo®

Deck Wash Hose Nozzle - Shurflo®

Hose - Heavy Duty Deck Wash - Shurflo®

Deck Wash Hose Connector - Shurflo®

23952 Shurflo® Deck Wash Hose Nozzle

GHTF

Swivel Wing Nut Connector suits Shurflo® Hose Coils

/

GHTM

Shurflo® deck wash pump.

23748

23762 Shurflo® deck wash hose coil,

453392 snap-on hose fitting supplied with the Relaxn® hose coil kits above.

Deck Wash Hose Coil Kits & Accessories

• Nozzle has a lock clip for continuous water flow and a comfortable handle.

• High grade seals.

• Stainless steel spring reduces kinking.

• Non-corrosive high-impact construction for long life.

• Includes 3/4"BSP threaded Snap-on hose connectors at each end.

Snap-On Hose Adaptors

and with Female

• Supplied with high quality nylon TruDesign® Power-Spray Nozzle with adjustable spray pattern for washdown and filling applications.

• Includes 3/4" BSP Snap-on hose connectors at each end.

• Coiled hose can be stored neatly in compact areas.

• Advanced hose coil design is resistant to kinking.

Power-Spray Nozzle - TruDesign®

• Adjustable spray pattern - Versatile usage for washdown or filling applications

• Supplied complete with 3/4" BSPM Snap-on garden hose connector.

• Super tough Nylon 6 Body - High strength and light weight.

• Auto shutoff - Won’t continue to use water if dropped.

Deck Wash - Hose Coil Kit - Recessed

• Flush Mount Washdown Hose Kit suited for both marine and RV applications.

• Multi-setting spray head with spring trigger, flow lock and integral safety on-off valve.

• Collapsible rubber hose in blue nylon fabric protective sleave expands from 2.8m to 4.2m.

• The Lid is simple to remove with a 15-degree twist, and a lanyard is attached to prevent misplacement.

• Inlet hose tail 1/2" - 5/8" (13 - 16mm) I.D.

• The lid is made from Saralon resin and the storage tube is made from Polypropylene.

23742

Deck

Wash Hose Coil Kits with Flush Link

• Designed to provide a complete deck wash hose coil solution, integrating a 316G stainless steel flush link, enabling the hose coil to be easily removed and stored out the way until required.

• Each kit contains a choice of complete hose coil with trigger nozzle, straight or angled flush link and the appropriate fitting to connect the relevant intake flexible hose or DMfit® QC Tubing to the flush link. Flexible hose and clamps or DMfit® QC Tubing is not included.

• Flush link adaptor is moulded from high strength and durable nylon 66 with GHTM thread to connect the hose.

• Adaptors feature a positive lock, 3 point bayonet connector and can be connected and disconnected under full pressure.

• Designed to provide a complete deck wash hose coil solution, integrating a 316G stainless steel flush link, enabling the hose coil to be easily removed and stored out the way until required.

• Each kit includes a choice of complete hose coil with trigger nozzle, straight, angled or angled flush link with on-off faucet. The appropriate fitting is also included to connect the relevant intake flexible hose or DMfit® QC Tubing to the flush link. Flexible hose and clamps or DMfit® QC Tubing is not included.

• Kits to suit 1/2" I.D. flexible hose or 12mm O.D. DMfit® QC Tubing plumbing system are supplied with the Relaxn® Standard hose coil.

• Kits to suit 3/4" I.D. flexible hose or 15mm O.D. DMfit® QC Tubing plumbing system are supplied with the Relaxn® Deluxe hose coil.

• Flush link adaptor is moulded from high strength and durable nylon 66 with BSPM thread to connect the hose.

• Adaptors feature a positive lock, 3 point bayonet connector and can be connected and disconnected under full pressure.

• 316G cast stainless steel.

• 3/4" BSPF thread outlet with slip nut.

• 1/2" BSPF thread inlet.

• Can be used as a deck wash outlet and water inlet.

• Nylon plug with safety chain.

• No integral valve.

Deck Wash Outlet - BSP

Deck Wash Hose Coil Kits with Flush Link - GHT Thread

Deck Wash Hose Coil Kits with Flush Link - BSP Thread

Deck Wash Flush Links & Outlet

Deck Wash Flush Links - GHT - 3 Point Bayonet

23895 Spare O-ring to suit

• Positive lock 3 point bayonet connector.

• Flush mount.

• Connects and disconnects under full pressure.

• Adaptor moulded from Nylon 66.

• Deck Wash Outlet cast in 316G Stainless Steel.

• Double Viton O-ring seals.

• Large flow capacity.

Deck Wash Flush Links & Faucets - BSP - 3 Point Bayonet

• Positive lock 3 point bayonet connector.

• Ideal for campers, RVs, off-road vehicles, canopy fit-outs and DIY applications etc.

• Connects and disconnects under full pressure.

• Adaptor moulded from nylon 66.

• Deck Wash Outlet cast in 316G Stainless Steel.

• Double Viton O-ring seals.

• Large flow capacity.

• Operating Pressure: 25 - 125 PSI

Deck Wash Outlet - Shut Off Tap - GHT

• Rugged non-corrosive moulded polypropylene.

• Integral on/off ball valve.

Tap Push Button with Timer & Installation Kits

Tap - Push Button with Timer

Cartridge & Timer Mechanism - 20 Seconds

Cartridge & Timer Mechanism - 8 Seconds

The new Push Tap with Timer is ideal when your hands are full or you just can’t reach the water. Simply push the button with your knee to start the timer and it automatically shuts off the water after 8 seconds, making it ideal for cleaning hands, bait boards and utensils. The Push Tap with Timer is commonly branched off the water feed from the deck wash pump to the hose coil outlet.

• Enjoy hands free water supply at the touch of a button.

• Brass body and chrome plated push button.

• 8 second timer will automatically shut water off.

• Adjustable flow rate, set to 40 PSI as default.

• 1/2" BSPM inlet and outlet.

• Made in Italy.

NOTE: We recommend flushing with fresh water if sea water has been pumped through the tap.

If fitted in a system incorporating a flush link, the timer tap can be flushed with fresh water by connecting a 23891 adaptor with faucet to the flush link, screwing on a 45339N snap-on hose adaptor, fitting a standard snap-on garden hose and carefully pressuring the system by minimally opening the faucet. The flush tap can then be activated, flushing it out with fresh water. Refer the practical use video available via the QR code.

Push Tap with Timer Installation Kits

• Designed to provide a complete Push Tap with Timer installation solution when fitted in conjunction with a deck wash pump and hose coil outlet.

• Kits to suit flexible hose include 90° outlet skin fitting to suit 3/4" I.D. hose, a tee joiner for the inlet hose, tap inlet and outlet tails.

• Kits to suit DMfit® QC Tubing include 1/2" BSP fully threaded outlet skin fitting, 90° outlet connectors, Y divider for the inlet tubing, tap inlet and outlet connectors.

• Flexible hose and clamps or DMfit® QC Tubing is not included.

NOTE: 3/4" I.D. flexible hose is required between the timer tap and outlet on the 510452, 510472 and 510512 versions.

Scan the QR code to watch the YouTube video.

Salt Water Deck Wash - Trailer

Water Pickup Kits - Deck Wash

• Designed to provide a complete deck wash pump pickup solution, commonly installed on trailerable power boats.

• Each kit includes a streamlined through-hull water pickup, ball valve and the appropriate fittings to connect the relevant intake flexible hose or DMfit® QC Tubing. Flexible hose and clamps or DMfit® QC Tubing is not included.

• A choice of 3/4" BSP nylon, standard or SuperSucker stainless steel pickup and PVC, stainless steel or Trudesign compact ball valve is available.

• 1/2" I.D. flexible PVC hose and 12mm DMfit® QC Tubing plumbing systems are not recommended for use with the Shurflo® ProBlaster 18.9L/min pressure pumps.

Nylon Pickup & PVC Ball Valve Kits

Stainless Steel Pickup Kits

SuperSucker Pickup Kits

NOTE: Polypropylene 3/4" BSPM x 1/2" I.D. hose tail

with 239471 and 239475

Salt Water Deck Wash - Trailer Boat Water Pickup Kits

Pick-Up - Thru-hull - Super Sucker - 3/4" BSPM

3/4" BSPM 95 Polished 316G S/S

• Hydrodynamic design for optimal water flow.

• High flow efficiency.

• Cast 316G stainless steel.

• Does not protrude - no impact on trailer skids or rollers.

• Engineered to reduce cavitation and air lock issues.

• Minimises interference with transducers.

• Can reduce chine walking for a smoother ride.

Pick-Up - Thru-hull - 3/4" BSPM

23040 3/4" BSPM 65 White Nylon

23040B 3/4" BSPM 65 Black Nylon

23042 3/4" BSPM 65 Polished S/S

• Shape reduces drag and aids water intake whilst underway at

• 316G stainless steel ball, stem and handle.

• Full bore parallel BSP (Female) threaded ports.

• Use with saltwater pick-ups above.

Ball Valve - TruDesign - Compact - 3/4" BSPF

450085 3/4" BSPF

• Glass reinforced nylon compositeHigh strength and light weight new compact design.

• Immune to corrosion and electrolysis for long service life.

• UV resistant, suitable for all marine environments.

• Large operating temperature range from -40°C to +110°C.

• Certified to ABYC H27, ISO 9001, AWQC, IMCI ISO 9093-2 and Burea Veritas 27801/A0 standards.

NOTE: TruDesign® Compact Ball Valves should not be used in direct contact with petrol or diesel as the nitrile O-ring may swell affecting their sealing and handle-turning performance.

• Compact style non-corrosive PVC ball valve with large handle.

• Full bore parallel BSP (Female) threaded ports.

• Use with saltwater pick-ups above.

450085

Ball Valve - Stainless Steel - 3/4" BSPF

Ball Valve - PVC - 3/4" BSPF

Salt Water Deck

Wash - Deck Wash / Bait Pump & Pickup Kits

Water Pickup Kits - Deck Wash / Bait Pump

• Designed to provide a complete sea water pickup solution to feed both deck wash and bait tank pumps from the one through-hull fitting.

• Each kit includes a 23035 Shurflo® Piranha dual port live bait tank pump, live bait tank aerator, streamlined through-hull water pickup, ball valve and the appropriate fitting to connect the relevant intake flexible hose or DMfit® QC Tubing to the deck wash pump. Flexible hose and clamps or DMfit® QC Tubing is not included.

• Flexible 3/4" I.D. PVC hose is used between the Shurflo® Piranha bait tank pump and the aerator.

• A choice of 3/4" BSP nylon, standard or SuperSucker stainless steel pickup and PVC, stainless steel or Trudesign compact ball valve is available.

• 1/2" I.D. flexible PVC hose and 12mm DMfit® QC Tubing plumbing systems are not recommended for use with the Shurflo® ProBlaster 18.9L/min pressure pumps.

Pumps - Live Bait - Dual Port

Live Bait Pumps

• 12VDC Live Bait tank water circulation pump.

• High density nylon housing and heavy duty water cooled motor give the Shurflo® Livewell Pumps unparalleled reliability.

• Patented anti-airlock feature allows the pump to clear trapped air in rough water or when the boat is anchored.

• The dual port fitting allows for easy washdown pump connections.

• Piranha Series Livewell Pumps have a removable cartridge for easy cleaning.

• Includes tinned 6ft (1.8M) wire assembly, 16 AWG.

• CE Certified, Ignition Protected ISO 8846.

• RCM Certified to Australian Standards.

Pumps - Live Bait - Bait Sentry™ Magnetic Drive

• The Bait Sentry™ Livewell Pumps are designed for easy installation and trouble-free operation.

• Magnetic Drive technology eliminates unnecessary failures.

• Motors keep running after ingesting debris or even when running dry.

• Patented anti-airlock feature allows the pump to clear trapped air in rough water or when the boat is anchored.

• The dual port inlet fitting allows for easy washdown pump connections.

• Includes tinned 6ft (1.8M) wire assembly.

• Can be installed horizontally or vertically.*

• CE Certified, Ignition Protected ISO 8846.

• RCM Certified to Australian Standards.

NOTE *See website for complete installation options.

Pumps & Plumbing

Live Bait Pumps

Pumps - Live Bait - High Flow

Threaded Polypropylene Nipple - 1"BSPM to 1"BSPM

• High-density nylon housing and a robust water-cooled motor ensure unparalleled reliability.

• Patented anti-airlock feature clears trapped air in rough water or when anchored.

• The dual port fitting allows for easy washdown pump connections.

• High flow rate Live Bait Pumps available in 1500 GPH and 2000 GPH.

• Must be mounted below waterline - does not self prime.

• Attaches to ball valve using 453125 male threaded nipple.

• Submersible.

• Includes tinned 6ft (1.8M) wire assembly, 16 AWG.

• CE, IMCI Certified, Ignition Protected ISO 8846.

• RCM Certified to Australian Standards.

Pumps - Live Bait - Angled Port

• High density nylon housing and heavy duty water cooled motor give the Shurflo® Livewell Pumps unparalleled reliability.

• Patented anti-airlock feature allows the pump to clear trapped air in rough water or when the boat is anchored.

• These aerator pumps have a removable cartridge for easy cleaning.

• Includes tinned 6ft (1.8M) wire assembly, 16 AWG.

• CE Certified, Ignition Protected ISO 8846.

• RCM Certified to Australian Standards.

NOTE: Use with 23570, 23572 or 45070 strainers.

• Fills and aerates Live Well while underway.

• Mounts over aerator pump intake.

• Built in filter screen.

NOTE: Use with angle port pumps 23025, 23029 and 23031

• Ideal for raw water intake for gen-set or live bait tank.

• Stainless steel mesh provides maximum water flow while filtering course debris.

•  45070 polypropylene base threads onto the inlet pipe of common live bait pumps.

232130 /

Strainer - Thru-hull - Stainless Steel

Pick Up Strainer - Horizontal Pump Intake

Pumps - Live Bait Tank - TMC

23026 Livewell Motor Cartridge - Suits 23023 / 23024 / 23025

• The TMC Livewell Pump design provides the convenience of using one intake for both Livewell and a washdown pump connection. A breather hole allows the pump to clear trapped air while the boat is travelling through rough water or anchored.

• Available in three mounting configurations - threaded into a seacock, vertical through hull or horizontally through transom.

• Threaded inlet tube can be cut to desired length.

• 360° Rotatable Discharge Port suit 3/4" - 7/8" I.D. hose.

• Supplied with both straight and 90° discharge port tails.

• Submersible.

• Replaceable motor cartridge.

• Airlock prevention.

• Additional 1/2" NPTF port provides connection to a washdown pumpsupplied with blanking plug.

• Can be used with intake stainers 23570, 23572 or 45070 (refer to page 17).

• 23023 & 23024 can be used with pick-ups 23040, 23040B, 23042, 23039 (refer to page 14).

• CE Certified - Meets ISO-9001 and ISO-14001 manufacturing standards.

• RCM Certified to Australian Standards.

Live Bait Pump Accessories

Pumps - Live Bait - Heavy Duty - Shurflo® Pro Baitmaster™ II

• The Pro Baitmaster™ II Heavy Duty Livewell/Washdown Pumps can be used for live-well or washdown applications and general water transfer.

• The SHURCote II seamless motor shell and sealed switch protects the pump.

• Pump must be installed in a DRY location. Do not install pump in wet areas.

• Self-priming and can run dry without damage.

• Continuous duty rated when operated at < 10psi.

• RCM Certified to Australian Standards. Thermally Protected, CE Certified, Ignition Protected ISO 8846.

NOTE: All Shurflo® diaphragm type pressure pumps must be fitted with an inlet filter. Please Refer to page 7 for the options available to suit various plumbing systems. Do not use Teflon tape or sealing compounds on pump threads.

Pumps - Livewell Macerator - Shurflo®

Replacement Impeller Kit

• Designed specifically for fish box evacuations.

• Shurflo's Macerator pump features a premium impeller design with run-dry capability and includes a seamless shell motor with O-ring sealed end bells and a sealed manual turn key.

• Unique dual blade and housing construction ensures problem free pumping, providing superior performance.

• Port Size: Inlet: 1-1/2" Outlet 1".

• RCM Certified to Australian Standards. Thermally Protected, CE Certified, Ignition Protected ISO 8846.

Pumps - Livewell - Diaphragm - TMC

• Single diaphragm pump designed to handle livewell drain applications.

• Self-priming pump can be run dry.

• Non-choke valve, no filter required.

• Can pump a mixture of air and water.

• Aligned inlet and outlet valves to allow free flow of debris.

• Adjustable clamping ring allows the head assembly to be rotated 360° to accommodate plumbing position.

• CE Certified, ISO-9001 and ISO-14001.

• Port Size: Inlet: 3/4" Outlet 3/4"

Repair Kit - Diaphragm - Livewell Pump - TMC

45113 Diaphragm Livewell Pump Repair Kit

• Diaphragm and 2 x valves.

• Suits TMC Livewell Diaphragm pumps.

Rotate ports to desired position. Pump head can be rotated and fixed in 3 positions.

Bait Tank Scoop S/S Transom Mount

• Ideal for circulating fresh sea water through bait tank while under way.

• Transom mounted.

• Maximum head 1000mm.

• 316G stainless steel.

Bait Tank Scoop Suits Bilge Pump

• Mounts common bilge pumps to provide water circulation to live bait tanks.

• Designed for: Shurflo® - 500, 700 and 1000 Bilge pumps and Rule®- 360 and 500 Bilge pumps.

• 316G stainless steel.

• Transom mounted.

• 29082 Holding Bar allows Bilge Pump to mount without screws.

Bait Tank Pump Adjustable Bracket - Transom Mount

• Adjustable aluminium brackets mount common bilge pumps to provide water circulation to live bait tanks.

• Thumb screw adjustment clamp.

• Model with scoop is designed to provide circulation whilst underway.

• Transom mounted.

Live Bait Tank - Aerator Flow Valve

• Fully adjustable aerator head has been especially

to customise water flow to

• Easy installation.

• Suits 3/4" I.D. Hose.

Live Bait Pump Accessories

Bait Tank Overflow Tube - Threaded Drain

• The threaded livewell drain is located at the bottom of the bait tank, with the Livewell Overflow Tube threaded into it to serve as an overflow for your bait tank.

• This setup requires only one hole in the bait tank for both the overflow and the drain.

• Marine grade PVC construction for long life.

• Makes draining live wells/bait tanks easier than a plug.

• Livewell Overflow Tube can be cut to length to suit bait tank.

• The threaded livewell drain is located at the bottom of the bait tank, with the Livewell Overflow Tube threaded into it to serve as an overflow for your bait tank.

• This setup requires only one hole in the bait tank for both the overflow and the drain.

• Marine grade PVC construction for long life.

• Makes draining live wells/bait tanks easier than a plug.

• Livewell Overflow Tube can be cut to length to suit bait tank.

Saltwater Deck Wash Pump Systems

Saltwater Deck Wash and Live Bait Kit Combinations

The following pages detail examples of some popular combinations of the preceding deck wash and live bait tank components. Each of these combo kits are setup to suit flexible pressure hose (page 21 to 26) or DMfit quick connect tubing (page 27 to 35) and

can be purchased under the one SAW part number as noted.

Any combination of pump, filter kit, water pickup kit, hose coil kit and push timer tap kit, can be customised to facilitate regular purchases by an OEM builder, under a single SAW part number.

•

• 1 x 23952 Hose Nozzle - 3/4" GHTF - Shurflo®.

• 1 x 23748 Coiled Deck Wash Hose - 3/8" GHT - 7.6m - White.

• 1 x 23963 Swivel Hose Tail - 1/2" NPTF to 1/2" I.D. - Nylon.

• 1 x 23982 Swivel Adapter - 1/2" NPTF to 3/4" GHTM - Nylon.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

NOTE: Suits 1/2" I.D. flexible hose. Hose and clamps not included. All circled numbers refer to "Deck Wash System Diagram - Direct to Pump" above.

- White.

• 1 x 23964 Swivel Hose Tail - 1/2" NPTF to 3/4" I.D. - Nylon.

• 1 x 23982 Swivel Adapter - 1/2" NPTF to 3/4"

Suits 3/4" I.D.

hose. Hose and clamps not included. All circled numbers refer to "Deck Wash System Diagram - Direct to Pump" above.

Wash Pump & Flexible Hose Kits

Deck Wash System Diagram - Flush Link

Kit 239308E Includes:

• 1 x 239428 Pro Blaster™ II Washdown Pump

• 1 x 23740 Nozzle & 3/4" BSP tails. Deck Wash Hose Black 7.5m x 3/8" I.D. Snap-on.

• 1 x 23886 Flush Link 130° - 1/2" BSPF x 3/4" BSPM - Stainless Steel.

• 1 x 45361 Hose Tail - 1/2" BSPM x 15mm Tail - Polypropylene.

• 2 x 23963 Swivel Hose Tail - 1/2" NPTF to 1/2" I.D. - Nylon.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

NOTE: Suits 1/2" I.D. flexible hose. Hose and clamps not included. All circled numbers refer to "Deck Wash System Diagram - Flush Link" above.

239308 Includes:

• 1 x 239431 Pro Blaster™ II Deluxe 4.0 Pump - 12V -

• 1 x 23952 Hose Nozzle - 3/4" GHTF - Shurflo®.

• 1 x 23748 Coiled Deck Wash Hose - 3/8" GHT - 7.6m - White.

• 1 x 23882 Flush Link 130° - 1/2" NPTF x 3/4" GHTM - Stainless Steel.

• 1 x 23976 Hose Tail - 1/2" NPTM to 3/4" I.D. - Nylon.

• 2 x 23964 Swivel Hose Tail - 1/2" NPTF to 3/4" I.D. - Nylon.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

NOTE: Suits 3/4" I.D. flexible hose. Hose and clamps not included. All circled numbers refer to "Deck Wash System Diagram - Flush Link" above.

• 1 x 239426 Pro

• 1 x 23770 Hose Nozzle Trudesign® - 3/4" BSPM x Snap-on.

• 1 x 45339N Hose Adaptor 3/4" BSPF to Snap-on

• 1 x 23746 Deck Wash Hose Coiled HD - 7.5m x 1/2" I.D. Snap-on - Black.

• 1 x 23886

Deck Wash Pump & Flexible Hose Kits

•

• 1 x 23740 Nozzle & 3/4" BSP tails. Deck Wash Hose Black 7.5m x 3/8" I.D. Snap-on.

• 1 x 23886 Flush Link 130° - 1/2" BSPF x 3/4" BSPM - Stainless Steel.

• 1 x 45361 Hose Tail - 1/2" BSPM x 15mm Tail - Polypropylene

• 2 x 23963 Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 1 x 45603 Hose Tail - 3/4" BSPM x 15mm - Polypropylene.

• 1 x 45181 Ball Valve - 3/4" BSPF - PVC.

• 1 x 23040 Hi-speed Thru-hull Pickup - 3/4" BSPM - Nylon Steel.

NOTE: Suits 1/2" I.D. flexible hose. Hose and clamps not included. All circled numbers refer to "Deck Wash System Diagram - Flush Link with Pickup".

• 1 x 23748 Coiled Deck Wash Hose - 3/8" GHT - 7.6m - White.

• 1 x 23882 Flush Link 130° - 1/2" NPTF x 3/4" GHTM - Stainless Steel.

• 1 x 23976 Hose Tail - 1/2" NPTM x 3/4" I.D. - Nylon.

• 2 x 23964 Swivel Hose Tail - 1/2" NPTF x 3/4" I.D. - Nylon.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 1 x 45630 Hose Tail - 3/4" BSPM - Stainless Steel.

• 1 x 45546 Ball Valve 3/4" BSPF - Stainless Steel.

• 1 x 23042 Hi-speed Thru-hull Pickup - 3/4" BSPM - Stainless Steel.

NOTE: Suits 3/4" I.D. flexible hose. Hose and clamps not included. All circled numbers refer to "Deck Wash System Diagram - Flush Link with Pickup".

Deck Wash & Live Bait Pump & Flexible Hose Kits

• 1 x 23952 Hose Nozzle - 3/4" GHTF - Shurflo®.

• 1 x 23762 Coiled Deck Wash HD Hose - 1/2" I.D. 3/4"GHT - 7.6m - Blue.

• 1 x 23882 Flush Link 130° - 1/2" NPTF x 3/4" GHTM - Stainless Steel.

• 1 x 23976 Hose Tail - 1/2" NPTM to 3/4" I.D. - Nylon.

• 2 x 23964 Swivel Hose Tail - 1/2" NPTF to 3/4" I.D. - Nylon.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 1 x 45630 Hose Tail - 3/4" BSPM - Stainless Steel.

• 1 x 45546 Ball Valve 3/4" BSPF - Stainless Steel.

• 1 x 23039 Hydrodynamic High Speed Pick-up - 3/4" BSP 316G Stainless Steel.

NOTE: Suits 3/4" I.D. flexible hose. Hose and clamps not included. All circled numbers refer to "Deck Wash System Diagram - Flush Link with Pickup".

Kit 239311E Includes:

• 1 x 239428

• Examples of combination deck wash and live bait tank systems, ideal for washing decks, anchor chain and fish box cleaning.

• One through hull fitting provides sea water to both deck wash and live bait tank pumps.

• These kits suit flexible hose plumbing system.

• Similar systems to suit alternative plumbing systems such as DMfit quick connect tubing, intakes, filters, pumps, flush links and hose coils can be assembled using the components detailed on pages 5 to 12

• 1 x 23035 Piranha™ Livewell Pump dual

• 1 x 23740 Nozzle & 3/4" BSP tails. Deck Wash Hose Black 7.5m x 3/8" I.D. Snap-on.

• 1 x 23886 Flush Link 130° - 1/2" BSPF x 3/4" BSPM - Stainless Steel.

• 1 x 45361 Hose Tail - 1/2" BSPM x 15mm - Polypropylene.

• 1 x 23974 Hose Tail - 1/2" NPTM x 1/2" I.D. - Nylon.

• 2 x 23963 Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM

• 1 x 23036 Aerator Head 90° x 3/4" I.D. Nylon - White.

• 1 x 45181 Ball Valve - 3/4" BSPF - PVC.

• 1 x 23040 Hi-Speed Thru-hull Pickup - 3/4" BSPM - Nylon

NOTE: Suits 1/2" I.D. flexible hose. Hose and clamps not included. All circled numbers refer to "Deck Wash / Live Bait Pump Kit - Dual Port - Flush Link with Pickup" above.

Deck Wash / Live Bait Pump Kit - Dual Port - 13.2 LPM - Flush Link with Pickup - 1/2" I.D. Flex

Pumps & Plumbing

Kit 239311 Includes:

• 1 x 239431 Pro Blaster™

-

-

• 1 x 23035 Piranha™ Livewell Pump dual port - 12V, 600 GPH.

• 1 x 23952 Hose Nozzle - 3/4" GHTF - Shurflo®.

• 1 x 23748 Coiled Deck Wash Hose - 3/4" GHT - 7.6m - White.

• 1 x 23882 Flush Link 130° - 1/2" NPTF x 3/4" GHTM - Stainless Steel.

• 2 x 23976 Hose Tail - 1/2" NPTM x 3/4" I.D. - Nylon.

• 2 x 23964 Swivel Hose Tail - 1/2" NPTF x 3/4" I.D. - Nylon.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM

• 1 x 23036 Aerator Head 90° x 3/4" I.D. Nylon - White.

• 1 x 45546 Ball Valve - 3/4" BSPF - Stainless Steel.

• 1 x 23042 Hi-Speed Thru-hull Pickup - 3/4" BSPM - Stainless Steel

NOTE: Suits 3/4" I.D. flexible hose. Hose and clamps not included. All circled numbers refer to "Deck Wash / Live Bait Pump Kit - Dual Port - Flush Link with Pickup" on page 24

• 1 x 239426

• 1 x 23035 Piranha™ Livewell Pump dual port - 12V, 600 GPH.

• 1 x 23770 Hose Nozzle Trudesign® - 3/4" BSPM x Snap-on.

• 1 x 45339N Hose Adaptor 3/4" BSPF to Snap-on

• 1 x 23746 Deck Wash Hose Coiled HD - 7.5m x 1/2" I.D. Snap-onBlack.

• 1 x 23886 Flush Link 130° - 1/2" BSPF x 3/4" BSPM - Stainless Steel.

• 1 x 45600 Hose Tail - 1/2" BSPM x 3/4" I.D. - Polypropylene.

• 1 x 23976 Hose Tail - 1/2" NPTM x 3/4" I.D. - Nylon.

• 2 x 23964 Swivel Hose Tail - 1/2" NPTF x 3/4" I.D. - Nylon.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM

• 1 x 23036 Aerator Head 90° x 3/4" I.D. Nylon - White.

• 1 x 45546 Ball Valve - 3/4" BSPF - Stainless Steel.

• 1 x 23039 Hydrodynamic High Speed Pick-up - 3/4" BSP - 316G Stainless Steel.

NOTE: Suits 3/4" I.D. flexible hose.

Hose and clamps not included. All circled numbers refer to "Deck Wash / Live Bait Pump Kit - Dual Port - Flush Link with Pickup" on page 24 Deck Wash / Live Bait Pump Kit - Dual Port - 15.1 LPM - Flush Link with Pickup - 3/4" I.D. Flex

Deck Wash Pump Combo Kits

• Deck wash and live bait tank combo kit with stainless steel pickup and recessed mount, collapsible hose coil.

• Designed for use with 1/2" I.D. flexible PVC pressure hose to the deck wash and 3/4" to the bait tank.

Kit 239311S Includes:

• 1 x 239431 Pro Blaster™ II Deck Wash - 12V, 15.1 LPM.

• 1 x 23035 Piranha™ Livewell Pump dual port - 12V, 600 GPH.

• 1 x 23766 Flush Mount Washdown Hose Kit - 4.5 Metres.

• 1 x 23974 Hose Tail - 1/2" NPTM to 1/2" I.D. - Nylon.

• 2 x 23963 Swivel Hose Tail - 1/2" NPTF to 1/2" I.D. - Nylon.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 1 x 23036 Aerator Head 90° x 3/4" I.D. Nylon - White.

• 1 x 45546 Ball Valve - 3/4" BSPF - Stainless Steel.

• 1 x 23042 Hi-Speed Thru-hull Pickup - 3/4" BSPM - Stainless Steel.

NOTE: Suits flexible hose. Hose and clamps not included.

• Ideal setup for a deck shower, deck wash or for cleaning out live fish tanks, where the hose coil is connected direct to the pump.

• Self priming pump delivers 16.3 LPM at a pressure up to 40 PSI.

• Thermal overload cuts the power to the motor if it is drawing too much current from the supply for an extended time, protecting the longevity of the pump.

• The built-in check valve prevents water flowing back and helps the pump keep a constant flow of water.

• Quick release ports provide easy installation.

• The diaphragm pump design allows the pump to run dry without damage.

• CE Certified, Ignition Protected ISO 8846. 23800 Kit Includes:

• 1 x TMC Pressure Pump - 12V, 16.3 LPM (4.3 GPM)

• 2 x Snap-in port fittings with 1/2" I.D. hose barb.

• 2 x Snap-in port fittings with 1/2" BSPM thread.

• 1 x Snap-in port fitting with 3/4" I.D. hose barb.

• 1 x Snap-in port fitting with male snap-on connector suit spring coiled hose

• 1 x Snap-in port fitting with 3/4" BSPM thread

• 1 x 7m Spring coiled hose with brass snap-in hose fitting.

• 1 x Snap-in Strainer

• 1 x Adjustable jet sprayer with lockable lever and male snap-on fitting suit spring coiled hose.

• Modern design single gang switch panel.

• Backlight label provides easy recognition at night.

• 20A rated push reset circuit breaker.

• IP66 Waterproof.

• CE certified.

Washdown Kits - TMC

Wash - Switch Panel

Deck Wash Pump Combo - Push Timer Tap & Flush Link Retrofit Kit

239290 Push Timer Tap & Flush Link Kit Quick Connect

Kit designed to update an existing Deck Wash System with a GHT threaded coiled hose attached directly to the pump. It includes a timer tap and flush link connection for the coiled hose. Suitable for 13.2 LPM deck wash pumps and uses 12mm DMfit quick connect plumbing fittings.

Kit 239290 Includes:

• 1 x 510470 Tap Push Button Timer 8 Sec with Nylon Thru Hull Mount Black.

• 1 x 450049 Skin Fitting Trudesign Black Full Thread 1/2" BSPM.

• 1 x 23882 Flush Link 130° - 1/2" NPTF x 3/4" GHTM - Stainless Steel.

• 4 x 448032 DMfit Connector Straight 12mm Tube x 1/2" BSPPF.

• 1 x 448054 DMfit Adaptor Elbow Stem - 12mm Tube.

• 1 x 448016 DMfit Connector Elbow Swivel 12mm Tube x 1/2" BSPTM.

• 1 x 448044 DMfit Union Two Way Divider 12mm Tube x 12mm Tube.

• 1 x 448106-10 DMfit LLDPE Tube 12mm x 10m Roll - Green.

NOTE: Suits 12mm DMfit quick connect tubing.

Deck Wash Pump Combo - Twin Push Timer Tap & Flush Link Retrofit Kit

Push Timer Tap & Flush Link Retrofit Kit - 15mm DMfit

Quick Connect

239290A Push Timer Tap & Flush Link Kit Quick Connect

Kit designed to update an existing Deck Wash System with a GHT threaded coiled hose attached directly to the pump. It includes a timer tap and flush link connection for the coiled hose. Suitable for 15.1 and 18.9 LPM deck wash pumps and uses 15mm DMfit quick connect plumbing fittings.

Note: Refer to installation diagram at the bottom of page 27 Kit 239290A Includes:

• 1 x 510470

• 1 x 450049

• 1 x 23882

• 1 x 448216

• 2 x 448222

• 1 x 448232

• 1 x 448210

Tap Push Button Timer 8 Sec with Nylon Thru Hull Mount Black.

Skin Fitting Trudesign Black Full Thread 1/2" BSPM.

Flush Link 130° - 1/2" NPTF x 3/4" GHTM - Stainless Steel.

DMfit Connector Straight 1/2" BSPPF - 15mm Tube.

DMfit Connector Straight Swivel 1/2" BSPPF - 15mm Tube.

DMfit Connector Elbow Swivel 1/2" BSPPF - 15mm Tube.

DMfit Connector Elbow Swivel 1/2" BSPPM - 15mm Tube.

• 1 x 448250 DMfit Union Two Way Divider - 15mm Tube x 15mm Tube.

• 1 x 448308-10

DMfit LLDPE Tube 15mm x 10m Roll - Green.

Twin Push Timer Tap & Flush Link Retrofit Kit - 15mm DMfit Quick Connect

NOTE: Suits 15mm DMfit quick connect tubing. Part No. Description

Push Timer Tap & Flush Link Kit Quick Connect Kit designed as per the 239290A but with timer taps, one on each side of the vessel.

Kit 239291 Includes:

• 2 x 510470 Tap Push Button Timer 8 Sec with Nylon Thru Hull Mount Black.

• 2 x 450049 Skin Fitting Trudesign Black Full Thread 1/2" BSPM.

• 1 x 23882 Flush Link 130° - 1/2" NPTF x 3/4" GHTM - Stainless Steel.

• 1 x 448216 DMfit Connector Straight 1/2" BSPPF - 15mm Tube.

• 4 x 448222

DMfit Connector Straight Swivel 1/2" BSPPF - 15mm Tube.

• 2 x 448232 DMfit Connector Elbow Swivel 1/2" BSPPF - 15mm Tube.

• 1 x 448210

DMfit Connector Elbow Swivel 1/2" BSPPM - 15mm Tube.

• 2 x 448250 DMfit Union Two Way Divider - 15mm Tube x 15mm Tube.

• 1 x 448308-10 DMfit LLDPE Tube 15mm x 10m Roll - Green.

NOTE: Suits 15mm DMfit quick connect tubing.

Standard

Kit 239292 Includes:

• 1 x 239428 Pro Blaster™ II Washdown Pump

• 1 x 23740 Hose Nozzle & 3/4" BSP Tails. Deck Wash Hose Black 7.5m x 3/8" I.D. Snap-on.

• 1 x 23886 Flush Link 130° 1/2" BSPF x 3/4" BSPM - Stainless Steel.

• 1 x 510470 Tap Push Button Timer 8 sec with Nylon Thru Hull MountBlack.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 5 x 448032 DMfit Connector Straight 1/2" BSPPF x 12mm Tube.

• 1 x 448054 DMfit Adaptor Elbow Stem - 12mm Tube.

• 1 x 448016 DMfit Connector Elbow Swivel 1/2" BSPTM x 12mm Tube.

• 1 x 448044 DMfit Union Two Way Divider 12mm Tube x 12mm Tube.

• 1 x 448106-10 DMfit LLDPE Tube 12mm x 10m Roll - Green.

• 1 x 450049 Skin Fitting Trudesign Black Full Thread 1/2" BSPM.

NOTE: Suits 12mm DMfit quick connect tubing.

Deck Washdown Kit - 15.1 LPM - Flush Link & Timer Tap - 15mm Quick Connect Deck Wash Pump Combo - Flush Link & Timer Tap

Kit 239292A Includes:

• 1 x 239431 Pro Blaster™ II Deluxe 4.0 Pump - 12V - 15.1 LPM 60 PSI.

• 1 x 23952 Hose Nozzle - 3/4" GHTF - Shurflo®.

• 1 x 23748 Coiled Deck Wash Hose - 3/4" GHT - 7.6m - White.

• 1 x 23882 Flush Link 130° - 1/2" NPTF x 3/4" GHTM - Stainless Steel.

• 1 x 510470 Tap Push Button Timer 8 sec with Nylon Thru Hull MountBlack.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM

• 2 x 448216 DMfit Connector Straight 1/2" BSPPF - 15mm Tube.

• 2 x 448222

DMfit Connector Straight Swivel 1/2" BSPPF x 15mm Tube.

• 1 x 448210 DMfit Connector Elbow Swivel 1/2" BSPPM x 15mm Tube.

• 1 x 448232

• 1 x 448250

DMfit Connector Elbow Swivel 1/2" BSPPF x 15mm Tube.

DMfit Union Two Way Divider 15mm Tube x 15mm Tube.

• 1 x 448308-10 DMfit LLDPE Tube 15mm X 10m Roll Green.

• 1 x 450049 Skin Fitting Trudesign Black Full Thread 1/2" BSPM.

NOTE: Suits 15mm DMfit quick connect tubing.

Deck Wash Pump Combo - Blaster, Flush Link, Timer Tap & Pick-up Kits

Deck Washdown - 15.1 LPM 60 PSI - Blaster, Flush Link, Timer Tap & Pick-up - 15mm Quick Connect

Kit 239293 Includes:

• 1 x 239431 Pro Blaster™ II

• 1 x 510470 Tap Push Button Timer 8 sec with Nylon Thru Hull Mount Black.

• 1 x 23952 Hose Nozzle - 3/4" GHTF - Shurflo®.

• 1 x 23748 Coiled Deck Wash Hose - 3/8" GHT - 7.6m - White.

• 1 x 23882 Flush Link 130° - 1/2" NPTF x 3/4" GHTM - Stainless Steel.

• 1 x 448308-10 DMfit LLDPE Tube 15mm x 10m Roll Green.

• 1 x 448204 DMfit Connector Straight x 3/4" BSPPM x 15mm Tube.

• 2 x 448222 DMfit Connector Straight Swivel 1/2" BSPPF x 15mm Tube.

• 2 x 448216 DMfit Connector Straight 1/2" BSPPF - 15mm Tube.

• 1 x 448232 DMfit Connector Elbow Swivel 1/2" BSPPF x 15mm Tube.

• 1 x 448210 DMfit Connector Elbow Swivel 1/2" BSPPM x 15mm Tube.

• 1 x 448250 DMfit Union Two Way Divider 15mm Tube x 15mm Tube.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 1 x 23042 Hi-Speed Thru-hull Pickup - 3/4" BSPM - Stainless Steel

• 1 x 45546 Ball Valve 3/4" BSPF - Stainless Steel.

• 1 x 450049 Skin Fitting Trudesign Black Full Thread 1/2" BSPM.

• 10 x 448268 DMfit Collet Locking Clip - 15mm Tube.

NOTE: Suits 15mm DMfit quick connect tubing.

Deck Washdown - 15.1 LPM 60 PSI - Blaster, Flush Link, Timer Tap & Pick-up

- 15mm Quick Connect

Kit 239294 Includes:

• 1 x 239431 Pro Blaster™

• 1 x 510470 Tap Push Button Timer 8 sec with Nylon Thru Hull Mount Black.

• 1 x 23770 Hose nozzle Trudesign Power-Spray Black 3/4" BSPM x Snapon Hose Fitting.

• 1 x 45339N Hose Adaptor Nylon 3/4" BSPF to Snap-on Male.

• 1 x 23746 Coiled Deck Wash Hose HD 7.5m x 1/2" I.D. Snap-on - Black.

• 1 x 23886 Flush Link 130° 1/2" BSPF x 3/4" BSPM - Stainless Steel.

• 1 x 448308-10 DMfit LLDPE Tube 15mm x 10m Roll Green.

• 1 x 448204

• 2 x 448222

• 2 x 448216

• 1 x 448232

• 1 x 448210

DMfit Connector Straight x 3/4" BSPPM x 15mm Tube.

DMfit Connector Straight Swivel 1/2" BSPPF x 15mm Tube.

DMfit Connector Straight 1/2" BSPPF - 15mm Tube.

DMfit Connector Elbow Swivel 1/2" BSPPF x 15mm Tube.

DMfit Connector Elbow Swivel 1/2" BSPPM x 15mm Tube.

• 1 x 448250 DMfit Union Two Way Divider 15mm Tube x 15mm Tube.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 1 x 23042 Hi-Speed Thru-hull Pickup - 3/4" BSPM - Stainless Steel

• 1 x 45546 Ball Valve 3/4" BSPF - Stainless Steel.

• 1 x 450049 Skin Fitting Trudesign Black Full Thread 1/2" BSPM.

• 10 x 448268

DMfit Collet Locking Clip - 15mm Tube.

NOTE: Suits 15mm DMfit quick connect tubing.

• 1 x 23035 Pump

• 1 x 23952 Hose Nozzle - 3/4" GHTF - Shurflo®.

• 1 x 23748 Coiled Deck Wash Hose - 3/8" GHT - 7.6m - White.

• 1 x 23882 Flush Link 130° - 1/2" NPTF x 3/4" GHTM - Stainless Steel.

• 1 x 510470 Tap Push Button Timer 8 sec with Nylon Thru Hull Mount Black.

• 1 x 448308-10 DMfit LLDPE Tube 15mm x 10m Roll Green.

• 1 x 448202 DMfit Connector Straight x 1/2" BSPPM x 15mm Tube.

• 2 x 448222 DMfit Connector Straight Swivel 1/2" BSPPF x 15mm Tube.

• 2 x 448216 DMfit Connector Straight 1/2" BSPPF - 15mm Tube.

• 1 x 448232 DMfit Connector Elbow Swivel 1/2" BSPPF x 15mm Tube.

• 1 x 448210 DMfit Connector Elbow Swivel 1/2" BSPPM x 15mm Tube.

• 1 x 448250 DMfit Union Two Way Divider 15mm Tube x 15mm Tube.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 1 x 23036 Aerator Head 90° x 3/4" I.D. Nylon - White.

• 1 x 23042 Hi-Speed Thru-hull Pickup - 3/4" BSPM - Stainless Steel

• 1 x 45546 Ball Valve 3/4" BSPF - Stainless Steel.

• 1 x 450049 Skin Fitting Trudesign Black Full Thread 1/2" BSPM.

• 10 x 448268 DMfit Collet Locking Clip - 15mm Tube.

• 2 x 764058-1 Hose Clamp Stainless Steel Collared 16 - 24mm.

NOTE: Suits 15mm DMfit quick connect tubing. Requires 3/4" flexible hose from bait tank pump to aerator (not included).

Deck

Wash Pump Combo - Blaster, Flush Link, Timer Tap, Bait Tank Kits

Deck Washdown - 15.1 LPM 60 PSI - Blaster, Flush Link, Timer Tap, Bait - 15mm Quick

Connect

Kit 239296 Includes: • 1 x 239431 Pro Blaster™ II Deluxe

• 1 x 23035 Pump Live Bait Shurflo Piranha 600gph 12V.

• 1 x 23770 Hose nozzle Trudesign Power-Spray Black 3/4" BSPM x Snap-on Hose Fitting.

• 1 x 45339N Hose Adaptor Nylon 3/4" BSPF to Snap-on Male.

• 1 x 23746 Coiled Deck Wash Hose HD 7.5m x 1/2" I.D. Snap-on - Black.

• 1 x 23886 Flush Link 130° 1/2" BSPF x 3/4" BSPM - Stainless Steel.

• 1 x 510470 Tap Push Button Timer 8 sec with Nylon Thru Hull Mount Black.

• 1 x 448308-10 DMfit LLDPE Tube 15mm x 10m Roll Green.

• 1 x 448202 DMfit Connector Straight x 1/2" BSPPM x 15mm Tube.

• 2 x 448222 DMfit Connector Straight Swivel 1/2" BSPPF x 15mm Tube.

• 2 x 448216 DMfit Connector Straight 1/2" BSPPF - 15mm Tube.

• 1 x 448232 DMfit Connector Elbow Swivel 1/2" BSPPF x 15mm Tube.

• 1 x 448210 DMfit Connector Elbow Swivel 1/2" BSPPM x 15mm Tube.

• 1 x 448250 DMfit Union Two Way Divider 15mm Tube x 15mm Tube.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 1 x 23036 Aerator Head 90° x 3/4" I.D. Nylon - White.

• 1 x 23042 Hi-Speed Thru-hull Pickup - 3/4" BSPM - Stainless Steel

• 1 x 45546 Ball Valve 3/4" BSPF - Stainless Steel.

• 1 x 450049 Skin Fitting Trudesign Black Full Thread 1/2" BSPM.

• 10 x 448268 DMfit Collet Locking Clip - 15mm Tube.

• 2 x 764058-1 Hose Clamp Stainless Steel Collared 16 - 24mm.

NOTE: Suits 15mm DMfit quick connect tubing. Requires 3/4" flexible hose from bait tank pump to aerator (not included).

Kit 239296S Includes:

• 1 x 239426 Pro Blaster™ II

• 1 x 23035 Pump Live Bait Shurflo Piranha 600gph 12V.

• 1 x 23770 Hose Nozzle Trudesign Power-Spray Black 3/4" BSPM x Snap-on Hose Fitting.

• 1 x 45339N Hose Adaptor Nylon 3/4" BSPF to Snap-on Male.

• 1 x 23746 Coiled Deck Wash Hose HD 7.5m x 1/2" I.D. Snap-on - Black.

• 1 x 23886 Flush Link 130° 1/2" BSPF x 3/4" BSPM - Stainless Steel.

• 1 x 510470 Tap Push Button Timer 8 sec with Nylon Thru Hull Mount Black.

• 1 x 448308-10 DMfit LLDPE Tube 15mm x 10m Roll Green.

• 1 x 448202 DMfit Connector Straight x 1/2" BSPPM x 15mm Tube.

• 2 x 448222 DMfit Connector Straight Swivel 1/2" BSPPF x 15mm Tube.

• 2 x 448216 DMfit Connector Straight 1/2" BSPPF - 15mm Tube.

• 1 x 448232 DMfit Connector Elbow Swivel 1/2" BSPPF x 15mm Tube.

• 1 x 448210 DMfit Connector Elbow Swivel 1/2" BSPPM x 15mm Tube.

• 1 x 448250 DMfit Union Two Way Divider 15mm Tube x 15mm Tube.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 1 x 23037 Aerator Head 90° 3/4" Nylon Black.

• 1 x 23039 Hydrodynamic High Speed Pick-up - 3/4" BSP 316G Stainless Steel.

• 1 x 45546 Ball Valve 3/4" BSPF - Stainless Steel.

• 1 x 450049 Skin Fitting Trudesign Black Full Thread 1/2" BSPM.

• 10 x 448268 DMfit Collet Locking Clip - 15mm Tube.

• 2 x 764058-1 Hose Clamp Stainless Steel Collared 16 - 24mm.

NOTE: Suits 15mm DMfit quick connect tubing. Requires 3/4" flexible hose from bait tank pump to aerator (not included). Deck Washdown - 18.9 LPM 60 PSI - Blaster, Flush Link, Timer Tap, Bait - 15mm

Deck Wash Pump Combo - Blaster, Flush Link, Timer Tap, Bait Tank Kits

Deck Washdown - 18.9 LPM 60 PSI - Blaster, Flush Link, Timer Tap, Bait -

15mm Quick Connect

Ultimate

Kit 239296B Includes:

• 1 x 239426 Pro Blaster™

• 1 x 23035 Pump Live Bait Shurflo Piranha 600gph 12V.

• 1 x 23952 Hose Nozzle - 3/4" GHTF - Shurflo®.

• 1 x 23762 Coiled Deck Wash HD Hose - 1/2" I.D. 3/4" GHT - 7.6m - Blue.

• 1 x 23882 Flush Link 130° - 1/2" NPTF x 3/4" GHTM - Stainless Steel.

• 1 x 510450 Tap Push Button Timer 8 sec with Nylon Thru Hull Mount White.

• 1 x 448308-10 DMfit LLDPE Tube 15mm x 10m Roll Green.

• 1 x 448202 DMfit Connector Straight x 1/2" BSPPM x 15mm Tube.

• 2 x 448222 DMfit Connector Straight Swivel 1/2" BSPPF x 15mm Tube.

• 2 x 448216 DMfit Connector Straight 1/2" BSPPF - 15mm Tube.

• 1 x 448232 DMfit Connector Elbow Swivel 1/2" BSPPF x 15mm Tube.

• 1 x 448210 DMfit Connector Elbow Swivel 1/2" BSPPM x 15mm Tube.

• 1 x 448250 DMfit Union Two Way Divider 15mm Tube x 15mm Tube.

• 1 x 23956 Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 1 x 23036 Aerator Head 90° x 3/4" I.D. Nylon - White.

• 1 x 23039 Hydrodynamic High Speed Pick-up - 3/4" BSP 316G Stainless Steel.

• 1 x 45546 Ball Valve 3/4" BSPF - Stainless Steel.

• 1 x 450200 Skin Fitting Trudesign White Full Thread 1/2" BSPM.

• 10 x 448268 DMfit Collet Locking Clip - 15mm Tube.

• 2 x 764058-1 Hose Clamp Stainless Steel Collared 16 - 24mm.

NOTE: Suits 15mm DMfit quick connect tubing. Requires 3/4" flexible hose from bait tank pump to aerator (not included).

Water Tanks - Drinking - Moulded

• Moulded from high density green polyethylene.

• Includes removable inspection port complete with pick-up tube, 1-1/2" BSPF vented cap, 3/8" BSPM x 3/8"/ 1/2"stepped outlet tail and 3/8" BSPM x 5/8" / 3/4"stepped vent tail.

• Installation pattern for standard 5 hole level sensor moulded into tank.

NOTE: Add 30 mm height for vented cap. Add 80 mm height for swivel elbow inlet tail 45275, 100mm for 45261

• Flexible water tanks are quick and easy to install in almost any space and available in triangular, square or rectangular configurations.

• Made from strong thermoplastic elastomer.

• Double welded seams for durability and reliability.

• Rope eyelets placed on each corner for fastening

•

Tanks come with fittings and cap

Mounded pattern 5 hole level sensor

Fresh Water Tanks

Water Tanks Senders & Gauges

Water Tank Gauges - 5 Hole Mechanical

37390 200 45280 / 45282 / 45284 / 45286 / 45291 37392 290 45290 / 45292

• Clear lens with E-F Indicator.

• Simple level arm float style.

• Output signal: 240~33 OHMS.

• 316G stainless steel main body.

• SAE Standard: 5 mounting holes.

• Operating temperature: -40 Degree Celsius - +85 Degree Celsius.

• Protection Rating: IP67.

• 2mm thick FPM gasket.

• 250mm tinned wire with PVC cover.

• Stainless steel mounting screws included.

• 33mm float diameter.

Note: Other sizes are available refer page 365. Length is measured from underside of the flange to the base of the shaft.

Water Tank Gauges - Kus

• Double layer reinforced anti-fogging lens.

• Supplied with plug-in wiring harness (100mm).

• Waterproof rating of IP67.

• CE Certified.

Water Tank Senders - 5 Hole - Kus

Referance to tank senders - 5 hole

Fresh Water Pump Systems

Fresh Water Shower Kits

239300 60 Litre Flexible Tank & Shower Kit - 12 Volts

Kit 239300 Includes:

• 1 x 239330 - Shurflo® Aqua King™ II Jnr Freshwater Pump - 12V 7.6LPM.

• 1 x 51067 - Shower Head Storage Box - White plastic.

• 1 x 51010 - Shower Head - White plastic.

• 1 x 51008 - 2.5m flexible white Shower Hose - 1/2" BSP.

• 1 x 50800 - Flexible square water tank 60L, 73cm x 73cm.

• 1 x 23966 - Elbow Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 23963 - Straight Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 29825 - Deck filler plastic suit 1-1/2" I.D. hose.

• 1 x 45361 - Hose tail - 1/2" BSPM x 15mm I.D. - Polypropylene

• 1 x 23956 - Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 4 x 764002-1 - Stainless Steel Hose Clamp - 11mm - 18mm.

• 2 x 764018-1 - Stainless Steel Hose Clamp - 27mm - 51mm.

NOTE: Suits 1/2" I.D. (outlet) and 1-1/2" I.D. (inlet) flexible pressure hose (not included). Pump must be installed in a dry, dust free location. Do not use Teflon thread tape or sealing compound on pump threads.

239301 Includes:

• 1 x 239340 - Shurflo® Aqua King™ II Freshwater Pump - 12V 11.3LPM.

• 1 x 51067 - Shower Head Storage Box - White plastic.

• 1 x 51010 - Shower Head - White plastic.

• 1 x 51008 - 2.5m Flexible White Shower Hose - 1/2" BSP.

• 1 x 50802 - Flexible Rectangular Water Tank 100L, 73cm x 88cm.

• 1 x 23966 - Elbow Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 23963 - Straight Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 29825 - Deck filler plastic suit 1-1/2" I.D. hose.

• 1 x 45361 - Hose Tail - 1/2" BSPM x 15mm I.D. - Polypropylene

• 1 x 23956 - Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 4 x 764002-1 - Stainless Steel Hose Clamp - 11mm - 18mm.

• 2 x 764018-1 - Stainless Steel Hose Clamp - 27mm - 51mm.

NOTE: Suits 1/2" I.D. (outlet) and 1-1/2" I.D. (inlet) flexible pressure hose (not included). Pump must be installed in a dry, dust free location. Do not use Teflon thread tape or sealing compound on pump threads.

Pumps & Plumbing

• 1 x 51065 - Premium Shower Head, S/S Hose & Chromed Box Kit.

• 1 x 29634 - Stainless Steel Water Deck Filler suit 1-1/2" I.D. Hose.

• 1 x 50802 - Flexible Rectangular Water Tank - 100 Litre 73cm x 88cm.

• 1 x 23966 - Elbow Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 23963 - Straight Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 45361 - Hose Tail - 1/2" BSPM x 15mm I.D. - Polypropylene

• 1 x 23956 - Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 4 x 764002-1 - Stainless Steel Hose Clamp - 11mm - 18mm.

• 2 x 764018-1 - Stainless Steel Hose Clamp - 27mm - 51mm.

NOTE: Suits 1/2" I.D. (outlet) and 1-1/2" I.D. (inlet) flexible pressure hose (not included). Pump must be installed in a dry, dust free location. Do not use Teflon thread tape or sealing compound on pump threads.

Fresh Water Shower & Galley Kits

Freshwater Shower Kit - Rigid 39 Litre Tank - 7.6 LPM Aqua King II Jnr

239302 39 Litre Rigid Tank & Shower Kit - 12V

Kit Includes:

• 1 x 239330 - Shurflo® Aqua King™ II Freshwater Pump Jnr - 12V - 7.6LPM.

• 1 x 45282 - 39 Litre Rigid Water Tank 55cm x 39cm x 28cm (including inlet elbow).

• 1 x 51074 - Shower Box with 1/2" BSPF Hose & Nozzle.

• 1 x 23966 - Elbow Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 23963 - Straight Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 45361 - Hose Tail - 1/2" BSPM x 15mm I.D. - Polypropylene

• 1 x 45275 - Swivel Elbow Tail suit 1-1/2" I.D. Hose.

• 1 x 29634 - Stainless Steel Water Deck Filler suit - 1-1/2 I.D. Hose.

• 1 x 23956 - Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

• 1 x 30974 - Breather Stainless Steel suit 5/8" ID Hose.

• 4 x 764002-1 - Stainless Steel Hose Clamp - 11mm - 18mm.

• 2 x 764004-1 - Stainless Steel Hose Clamp - 11mm - 22mm.

• 2 x 764018-1 - Stainless Steel Hose Clamp - 27mm - 51mm.

NOTE: Suits 1/2" I.D. (outlet) 5/8" I.D. (breather) and 1-1/2" I.D. (inlet) flexible pressure hose (not included). Pump must be installed in a dry, dust free location. Do not use Teflon thread tape or sealing compound on pump threads.

239318 Freshwater Pump & Chromed Galley Faucet Kit - 12V

• The Aqua King Pump is designed for quiet smooth performance while providing durability and reliability.

• Chrome plated brass faucet mounts to right hand side of sink and folds down into sink when not in use.

• Pump is RCM Certified to Australian Standards. Thermally Protected, IMCI Certified, CE Certified, Ignition Protected ISO 8846. Kit includes:

• 1 x 239330 - Shurflo® Aqua King™ II freshwater pump Jnr 12V - 7.6 LPM.

• 1 x 51014 - Chromed brass single right hand tap and faucet 3/8" BSPM thread.

• 1 x 23966 - Elbow Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 23963 - Straight Swivel Hose Tail - 1/2" NPTF x 1/2" I.D. - Nylon.

• 1 x 51017 - Hose Tail 3/8" BSPF x 1/2" I.D. Brass.

• 1 x 23956 - Water Strainer - Swivel Nut 1/2" NPTF x 1/2" NPSM.

NOTE: Suits 1/2" I.D. flexible pressure hose (not included). Hose clamps not included. Pump must be installed in a dry, dust free location. Do not use Teflon thread tape or sealing compound on pump threads.

Tips For Installing Shurflo® Pumps

Mounting:

• Consider a dry and dust free location that allows easy access if maintenance is required.

• Excessive heat may trigger the integral thermal breaker and interrupt operation, When the temperature drops the pump will start operating again.

• If mounting the pump vertically the pump head should always be positioned downwards. Shurflo® recommends at least 1ft. of 1/2" I.D. flexible high pressure tubing on the inlet if using rigid tubing system.

• Shurflo® hex/swivel barb fittings provide easy removal.

• Shurflo® fittings are designed with a taper-seal, creating a water tight connection when hand-tightened.

• Do not use Teflon thread tape or sealing compound on pump threads.

Freshwater Galley Kit - 7.6 LPM Aqua King II Jnr

Fresh Water Pumps

Pump - Fresh Water - Aqua King™ II Jr 2.0 & Standard 3.0

• Pentair Shurflo® Aqua King™ II Junior & Standard Fresh Water Pumps are designed with a unique over-moulded single-piece diaphragm and internal bypass (3.0 version) for long life and reliable performance.

• These freshwater automatic demand pumps are quiet and can run dry without damage.

• Features heavy-duty, seamless shell electro-coated motors.

• Factory set adjustable pressure switch.

• Self priming up to 1.8m.

• Inlet & Outlets Ports: 1/2" NPSM.

• Mounting screw size Ø 3/16" (4.8mm).

• RCM Certified to Australian Standards. Thermally Protected, CE, IMCI Certified, Ignition Protected ISO 8846.

NOTE: Pump must be installed in a dry, dust free location. Do not use Teflon thread tape or sealing compound on pump threads.

NOTE: Pump must be installed in a dry, dust free location. Do not use Teflon thread tape or sealing compound on pump threads. Pump - Fresh Water 15.1 LPM - Aqua King™ II Premium 4.0

• Pentair Shurflo® Aqua King™ II Premium Fresh Water Pumps are designed for boats with multiple fixtures use, providing "just like home" water pressure.

• A built in mechanical bypass function enables these pumps to operate at lower flow conditions with minimal cycling.

• Features heavy-duty, seamless shell electro-coated motors.

• Factory set adjustable pressure switch.

• Self priming up to 1.8m.

• Inlet & Outlets Ports: 1/2" NPSM.

• Mounting screw size Ø 3/16" (4.8mm).

• RCM Certified to Australian Standards. Thermally Protected, CE, IMCI Certified, Ignition Protected ISO 8846.

• Pentair Shurflo® Aqua King™ II Supreme Fresh Water Pumps are designed for boats with multiple fixtures use, providing "just like home" water pressure.

• A built in mechanical bypass function enables these pumps to operate at lower flow conditions with minimal cycling.

• Features heavy-duty, seamless shell electro-coated motors.

• Factory set adjustable pressure switch.

• Self priming up to 1.8m.

• Inlet & Outlets Ports: 1/2" NPSM.

• Mounting screw size Ø 3/16" (4.8mm).

• RCM Certified to Australian Standards. Thermally Protected, CE, IMCI Certified, Ignition Protected ISO 8846.

NOTE: Pump must be installed in a dry, dust free location. Do not use Teflon thread tape or sealing compound on pump threads.

Fresh Water Pumps

Fresh Water Pump - Aqua King™ II High Flow - Dual Pump

High Performance

• The most advanced water pressure system available. These fully-automatic, quiet units deliver water smoothly and consistently.

• System contains: Pentair Shurflo® Aqua King™ II Supreme 5.0 GPM and Pentair Shurflo® Pro Blaster™ II Ultimate 5.0 GPM, manifold assembly and mounting board.

• Variable-speed, smooth flow for quiet operation.

• High-flow capability - 37.8 LPM.

• Reduces fluctuations in water pressure.

• Improves performance of showers, heads and faucets.

• Wide flow range for single and multiple fixture use.

• Eliminates need of an accumulator tank.

• Pump port 1/2" NPSM.

• Ports 1/2" NPTF tail connected manifold with 3/4" barbed tail outlet.

• RCM Certified to Australian Standards. Thermally Protected, CE, IMCI Certified, Ignition Protected ISO 8846.

NOTE: Pump must be installed in a dry, dust free location. Do not use Teflon thread tape or sealing compound on pump threads.

Fresh Water Pump - SLV Lo-Flo

Fresh Water RV Pumps

• This compact automatic demand pump offers durability and dependability making it ideal for low volume, intermittent duty applications.

• The SLV Pump self-primes up to 0.7m vertically while delivering over 3.8 LPM.

• Low power consumption motor, provides high pump performance and reliability.

• Mounting screw size Ø 3/16" (4.8mm).

• RCM Certified to Australian Standards.

NOTE: Pump must be installed in a dry, dust free location. Do not use Teflon thread tape or sealing compound on pump threads.

• SHURflo's 4009 series RV Pump is created with unique one-piece 4 Chamber Diaphragm and internal by-pass, assuring long life and reliable performance in all RV plumbing systems.

• Designed for multi-fixture RV installation.

• Suitable for general fresh water transfer.

• Provides quiet automatic demand fresh water supply on, intermittent duty cycle.

• Ports 1/2" NPSM

• Filter should be mounted remotely from pump. If connecting directly to inlet port, care must be taken not to over-tighten and crack the threaded port.

• RCM Certified to Australian Standards.

NOTE: Caravan and RV use ONLY, Not rated for marine use. Pump must be installed in a dry, dust free location. Do not use Teflon thread tape or sealing compound on pump threads.

Fresh Water Pumps - RV

Pump - Spare Parts - SHURflo

Filters & Hose Tails

Filter Kits - Fresh Water Inlet

• A filter must be fitted on the inlet side of all Shurflo® fresh water pumps to prevent entry of debris to the pump body.

• The filter must be mounted above the waterline to prevent syphoning during cleaning, without closing the inlet valve.

• If DMfit® QC Tubing is used on the inlet, Shurflo® recommends the pump inlet port is plumbed with a minimum of 300mm of flexible PVC pressure hose.

• Standard inlet filters are mounted remotely from the pump inlet port.

• Swivel nut filters are mounted directly to the pump inlet port.

• Each kit includes - filter, filter hose tails, pump inlet and outlet tails where applicable. Other flexible hose and hose clamps or DMfit® QC Tubing is not included.

• 1/2" I.D. flexible PVC hose and 12mm DMfit® QC Tubing plumbing systems are not recommended for use with the Shurflo® 18.9L/min pressure pumps.

Filters - Water Inlet - Small

• Essential requirement on all Shurflo® pressure pumps.

• Fixed mount is fitted remotely from the pump.

• Swivel nut version is fitted directly to pump.

• Compact design.

• Keeps debris out of pump.

• Transparent, easy to see when strainer needs cleaning.

• Stainless steel mesh screen.

• Suits Shurflo's 1/2" NPSM Male Port Pumps.

NOTE: Do not use Teflon thread tape or sealing compound.

Flexible Hose Inlet Adaptor

Flexible Hose Inlet

• Shurflo recommends that a short flexible hose be connected directly to the inlet port when using a rigid tubing plumbing system. This minimises noise and vibration.

• Pre-assembled ready for installation.

• 300mm flexible hose length.

• Swivel wingnut tail connects to filter port.

Filters - Water Inlet - Large

Replacement S/S Mesh Screen

• Designed to keep your water pressure pumps protected from harmful debris.

• Mounted remotely from the pump.

• Twist off polyamide bowl and removable stainless steel screen, which allows for easy inspection and cleaning.

• Integral O-ring creates a tight seal, eliminating possible leaks.

Swivel Wingnut Hose Tails - Shurflo®

Accumulator Tanks & Pressure Regulators

Accumulator Tank - Nylon

23962 1/2" NPSF Wingnut Swivel Adaptor

• Bladder type pressure storage tank.

• Reduces cycling pulsation and pressure spikes.

• Handles pressure requirements up to 125 PSI.

• Increases the life of your pressure switch controlled pumps.

• Must be pre-charged before use.

23959 - Includes 23962 adaptor.

23959A - Accumulator only

23962 - Swivel wing nut adaptor 1/2" NPTF - 1/2" NPTF facilitates direct attachment to outlet port of Shurflo® pressure pumps (must be supported using mounting bracket).

Fresh Water Inlet - Pressure Regulators - Recessed

45335 3/4" GHTM - Snap-on Hose Inlet Adaptor.

• Diaphragm design prevents high-pressure damage often caused by mains pressure water systems.

• Reduces mains water pressure to 65psi.

• Maximum inlet pressure of 125 psi.

• Leak-tight, stress and crack-resistant, while surpassing all check valve code requirements.

• Include a check valve.

• 3/4" GHTF inlet accepts 45335 3/4" GHTM x snap-on hose tail.

• 1/2" NPSM outlet.

Accumulator Tank - Stainless Steel

• Large stainless steel tank with a butyl bladder.

• Reduces cycling pulsation and pressure spikes.

• Handles pressure requirements up to 100 PSI.

• Increases the life of your pressure switch controlled pumps.

• Top plate is pre-drilled and tapped with 10-32 UNF threads to facilitate direct mounting of shurflo 15.1 and 18.9 l/min pressure pumps.

• Must be pre-charged before use.

Flexible Hose Inlet Adaptor

• Shurflo recommends that a short flexible hose be connected directly to the outlet port of the pressure regulator when using a rigid tubing plumbing system. This minimises noise and vibration.

• Pre-assembled ready for installation.

• 300mm flexible hose length.

• Swivel wingnut tail connects to pressure regulator outlet port.

45335

Inline & Manual Pumps

Pump - Inline - Water

• Non-self-priming inline centrifugal pump.

• Suitable for intermittent operation only.

• Sonic-welded and submersible. Can be mounted inside water tank.

• Should be mounted vertically. Light weight to suspend in pipe work.

• Must be mounted at or below the bottom of water tank.

• CE Certified ISO 8846 Marine (Ignition Protection) & ISO 8849 Marine (Bilge Pump Standard).

NOTE: Do not run pump dry.

Submersible Pump - Water

• Compact design enables installation within tank.

• Fully submersible designed for intermittent use only.

• Maximum continuous operation should not exceed 15 minutes.

• Low current draw.

• Hose Dia. 3/8" I.D.

• CE Certified ISO 8846 Marine (Ignition Protection) & ISO 8849 Marine (Bilge Pump Standard).

Submersible Inline Pumps - Rule®

• Centrifugal submersible or inline pump, with-snap-off strainer removed.

• Suitable for fresh and salt water or diesel fuel transfer.

• Must be mounted within or below the level of the tank.

• Suitable for continuos duty.

• Supplied with 4m cable and alligator clips.

• Pump Size: Ø 38mm x L 165mm.

• CE and ISO 8846 certification.

NOTE: Do not run dry for long periods. Flow rate at no head.

Pump - Drill Operated

• Ideal for water transfer, oil change, automatic transmission fluids, anti-freeze solutions, low viscosity gear oil and other nonflammible liquid transfer.

• Not suitable for petrol (gasoline).

• 1/4" shaft fits any common drill chuck.

• Self primes up to 8ft vertical, 25 feet horizontal.

• Pumps liquids 4°C - 50°C.

• Buna-N impeller seals.

• 3/4" GHT pump ports accept 453992 snap-on hose adaptor.

• Includes 900mm long 1/2" I.D. PVC pressure outlet hose and 750mm long 1/4" O.D. rigid poly inlet tubing.

• CE Certified.

Pump - Diaphragm Foot Operated

15.1 1/2" 237 x 153 x 124

• Self-priming and double acting.

• Adjustable multi-directional inlet and outlet hose connections.

• Can be installed inside a locker space with pedal only projecting.

• Suitable for fresh or salt water.

• CE Certified, ISO-9001 & ISO-14001.

Pump - Brass Sump

• 31mm O.D. brass bodied engine oil pump.

• Includes 600 mm long x 8 mm O.D. rigid poly inlet tubing and 250 mm x 12mm O.D. rigid poly outlet tube.

• Single action.

• Internal components are made from nitrile rubber.

• Extremely resilient and can withstand higher temperatures for oil changes.

Pump - Bronze Gear

• Self-Priming pump with bronze gears.

• Suitable for non highly flammable liquids transfer, including diesel fuel, anti freeze and lightweight lubrication oils not exceeding the viscosity index below*.

• Also suitable for bilge pumping.

• Inlet and outlet barbs suit 5/8" (16mm) I.D. hose.

• CE Certified ISO 8846 Marine (Ignition Protection).

• Filter is removable for cleaning and supplied with spare gauze.

• Positive power lead includes inline 3AG glass fuse holder.

NOTE: DO NOT use where flammable vapours are present.

Gear, Impeller, Ballast Tank, Desalination & Refrigeration Pumps

Pump - Ballast Tank - 1100GPH

• High density nylon housing and heavy-duty water cooled motor give the Piranha™ Shurflo® Ballast Pumps unparalleled reliability.

• Patented anti-airlock feature allows the pump to clear trapped air.

• All Piranha Series Ballast Pumps have a removable cartridge for easy cleaning.

• Submersible.

• Includes tinned 6ft (1.8M) wire assembly, 16 AWG.

• CE Certified, Ignition Protected ISO 8846.

• RCM. Certified to Australian Standards.

High Pressure Diaphragm Pump For Desalination

• Replacement pump for Spectra desalination.

• The SLV Pump self-primes up to 2.4m vertically while delivering over 6 LPM.

• Can run dry without damage.

• Built-in check valve.

• Thermally Protected, CE Certified, Ignition Protected ISO 8846.

• RCM Certified to Australian Standards.

Pump - Bronze Impeller

• Durable bronze body with rubber impeller.

• Suitable for fresh or saltwater applications (Not for drinking water).

• Coated base plate with rubber vibration dampening grommets.

• Positive power lead includes 3AG glass fuse holder.

• Inlet/Outlet (dual threaded):

Thread 1/2" BSPF.

Thread 3/4" GHTM.

• Self-priming, do not run dry.

• CE Certified ISO 8846 Marine (Ignition Protection).

NOTE: Avoid pumping solvent, thinners, or petrol to prevent impeller and motor damage.

Refrigeration Pump

• Designed for circulation to water cooled refrigeration condensers.

• Features a positive displacement 3 chamber diaphragm and EPDM valve for proven priming ability and longer life.

• No Switch.

• Continuous duty motor.

• 1/2" NPSM ports.

• Thermally Protected, CE Certified, Ignition Protected ISO 8846.

• RCM Certified to Australian Standards.

Manual Bilge Pumps

23528 Underdeck Mounting Bracket, Seal & Cover

23530 Service Kit

• Robust construction and large capacity with removable handle.

• Ideal for work boats and larger leisure craft

• Double diaphragm design ensures maximum capacity.

• Hand wheels allow easy access to the pumping chamber, no tools are required.

• Pump body is made from polyester coated aluminium.

• Fastenings and removable handle are made from stainless steel.

• Nitrile rubber diaphragms are fitted as standard.

• Mount holes Ø 10mm.

• Floor mount centres 130mm x 150mm.

• Optional underdeck mounting bracket with hinged cover plate available.

23537 Underdeck Mounting Flange and Seal

23532 Service Kit

• The Patay® DD100A Sea Master can be on-deck or underdeck mounted or alternatively, bulkhead or through bulkhead mounted.

• Double diaphragm design ensures maximum capacity.

• Easy access to the pumping chamber is provided by hand wheels, no tools are required.

• Pump body is made from polyester powder coated aluminium.

• Fastenings and removable handle are made from stainless steel.

• Nitrile rubber diaphragms are fitted as standard.

• Mount holes Ø 10mm.

• Floor mount centres 130mm x 150mm.

• Optional underdeck mounting flange and seal.

23537 Underdeck Mounting Flange and Seal

23532 Service Kit

• Double diaphragm design ensures maximum efficiency.

• Robust construction and large capacity are ideal for work boats and larger leisure craft.

• Easy access to the pumping chamber is provided by hand wheels, no tools are required.

• Pump body is made from polyester coated aluminium.

• Fastenings and removable handle are made from stainless steel.

• Nitrile rubber diaphragms are fitted as standard.

• Mount holes Ø 10mm.

• Floor mount centres 130mm x 150mm.

• Optional underdeck mounting flange and seal.

Pump - Bilge Manual - DD70A

Pump - Bilge Manual - DD100A

Pump - Bilge Manual - DD120A

Manual Bilge Pumps

Pump - Bilge Manual - SD60 - Underdeck

23529 Replacement Underdeck Mounting Flange and Seal to suit 23520 23536 Service Kit

• The Patay® Skipper SD60 is lightweight and designed for underdeck mounting.

• The body and ports can be positioned in multiple orientations for maximum flexibility of installation.

• Supplied with deck plate and seal.

• Reliable and durable, this pump will withstand regular use and will give years of trouble free operation.

• Pump is made from polypropylene with stainless steel fastenings and polyester coated castings.

• Removable stainless steel handle.

• Nitrile rubber diaphragms are fitted as standard.

• Supplied with two sets of alternative inlet and outlet ports to suit either 1" or 1-1/2" I.D. hose.

• Replacement underdeck mounting flange and seal available.

• The Patay® Skipper SD60 is lightweight and designed for surface mounting on the deck or bulkhead.

• The body and ports can be positioned in multiple orientations for maximum flexibility of installation.

• Fixed handle.

• Reliable and durable, this pump will withstand regular use and will give years of trouble free operation.

• Pump is made from polypropylene with stainless steel fastenings and polyester coated castings.

• Nitrile rubber diaphragms are fitted as standard.

• Supplied with two sets of alternative inlet and outlet ports to suit either 1" or 1-1/2" I.D. hose.

Pump - Bilge Manual - SD60 - Removable Handle

• The Patay® Skipper SD60 is lightweight and designed for surface mounting on the deck or bulkhead.

• The body and ports can be positioned in multiple orientations for maximum flexibility of installation.

• Removable stainless steel handle.

• Reliable and durable, this pump will withstand regular use and will give years of trouble free operation.

• Pump is made from polypropylene with stainless steel fastenings and polyester coated castings.

• Nitrile rubber diaphragms are fitted as standard.

• Supplied with two sets of alternative inlet and outlet ports to suit either 1" or 1-1/2" I.D. hose.

Pump - Bilge Manual - SD60 - Fixed Handle

Pump - Spare Parts - Patay®

23530 D120A Service Kit suit 23510

23532 DD100A / DD70A Service Kit suits 23514 & 23515 23536 SD60 Service Kit suits 23520, 23522 & 23523

23537 DD100A / DD70A Oval Deck Flange & Seal Kit

23527 Underdeck Seal & Cover Plate only suit 23528

23528 DD120A Underdeck Bracket, Seal & Cover suit 23510

23529 SD60 Underdeck Mounting Kit to suit 23520

• 23530 Service kit suits the Patay™ DD120 Ocean Master pump range. The kit is supplied with 2 nitrile diaphragms, 1 conrod, 1 diaphragm plate and 2 fixing screws and washers. Also suitable for Jabsco® Amazon Pump.

• 23537 Suitable for the Patay® DD100A/DD70A bilge pumps. Includes oval deck flange and seal. Also suits old style DD120A.

• 23529 Replacement underdeck mounting flange and seal suit Patay® SD60 Underdeck. Included as standard with 23520

Replacement Diaphragm to suit

• Economical deck or bulkhead mounted manual bilge pump with multiple handle to flow direction orientation choices.

• Black nylon construction.

• Removable stainless steel handle.

• This self priming pump will deliver approximately 50 litres of water per minute.

• Stepped inlet/outlet ports suit either 1" or 1-1/2" I.D. hose.

• Made from durable, non-corrosive plastic.

• Barbed inlet and outlet connectors fit 1" I.D. hose.

• Design facilitates a choice of surface or thru-deck mounting with alternative handle sockets included.

• Removable stainless steel handle.

• Thru-deck mounting: suitable for deck thicknesses ranging from 5mm to 19mm.

• Clamping ring design facilitates infinite handle position to flow direction orientation options.

• Kit includes through deck mounting plate with hinged lid and seal.

• Includes two plastic clips for handle storage.

Pump - Bilge Manual - Removable Handle

Pump - Bilge Manual - Surface or Thru-Deck Mount

Strum Box & Non-Return Valve - Patay®

23538 Strum Box Strainer suit 1" / 1-1/2" I.D. Hose

• Strum box strainer with integral non-return flapper valve.

• Supplied with alternative outlet ports to suit either 1" or 1-1/2" I.D. hose.

• Outlet port can be set horizontally or vertically.

• Suitable for use with all manual or electric bilge pumps with 1" or 1-1/2" I.D. inlet hose size.

• Allows flow in one direction only to safeguard against back surge up to 100 PSI (6.8 BAR).

Non-Return Valves - TruDesign®

• Glass reinforced nylon composite.

• Idea for stopping water back flow from siphoning.

• Stainless steel spring with low opening pressure.

• Minimal restriction on flow rate.

NOTE: TruDesign® Non-Return Valves should not be used in direct contact with petrol or diesel as the nitrile O-ring may swell affecting their sealing performance.

Non Return Valves - Patay®

• Suitable for all water pumping applications.

• Polypropylene body, neoprene flapper valve and stainless steel hardware.

• Can be converted to right angle.

Non-Return Valve - Stepped

• One way valve suitable for galley pumps.

• White nylon body with flapper valve.

• Smaller port can be cut off if not required.

• Stepped ports suits 1/2"and 3/4" I.D. hose sizes.

• Australian made.

Non-Return Valves - Stepped

• Stepped tail suits two different hose sizes.

• Smaller port can be cut off if not required.

• 1-1/8" size suits most common 1000 to 2000 GPH submersible bilge pumps.

• Made from reinforced black nylon with neoprene flapper valve and stainless steel fasteners.

•

Submersible Bilge Pumps

Pumps - Bilge - Compact - Shurflo®

232099 Bilge Pump Spare Base Plate suits Shurflo® 232100, 232101 & 232102

• Fully submersible with anti-airlock protection.

• Stainless steel shaft.

• Tough nylon impeller.

• Removable base mount for easy installation.

• Mounting clip suits 23224 Shurflo® Bilge Pump Float Switch*.

• 1.8m tinned wire.

• CE Certified, Ignition Protected ISO 8846.

• RCM Certified to Australian Standards.

Note: Ensure wiring connections remain above water level on all submersible bilge pumps and float switches. *Directly mounts on

Pumps - Bilge - Large - Shurflo®

• Tough nylon heavy duty housing.

• Patented water cooled motor ensures high performance and long life.

• Fully submersible with anti-airlock protection.

• Patented snap swivel base for easy installation.

• 1.8m tinned wire.

• CE Certified, Ignition Protected ISO 8846.

• RCM Certified to Australian Standards.

Note: Ensure wiring connections remain above water level on all submersible bilge pumps and float switches.

232099

Submersible Bilge Pumps

Pumps - Compact Bilge - TMC

• Fully submersible bilge pump.

• Permanent magnet motor.

• Compact design.

• Corrosion resistant plastic housing.

• Tough nylon impeller.

• Snap-on base strainer for easy mounting or cleaning.

• 0.9m tinned wire.

• CE Certified: Ignition Protected ISO 8846 & Bilge Pump Std ISO 8849.

Note: Ensure wiring connections remain above water level on all submersible bilge pumps and float switches.

• Fully submersible bilge pump.

• Permanent magnet motor.

• Compact design.

• Corrosion resistant plastic housing.

• Tough nylon impeller.

• Snap-off base strainer for easy mounting or cleaning.

• 0.9m tinned wire.

• CE Certified: Ignition Protected ISO 8846 & Bilge Pump Std ISO 8849.

Note: Ensure wiring connections remain above water level on all submersible bilge pumps and float switches.

Pumps - Bilge 4000 GPH - Submersible - TMC

• Fully submersible bilge pump.

• Permanent magnet motor.

• Heavy duty design for tough demands.

• High impact plastic housing.

• Tough nylon impeller.

• Snap-off base strainer for easy mounting or cleaning.

• 1.0m tinned wire.

• CE Certified: Ignition Protected ISO 8846 & Bilge Pump Std ISO 8849.

NOTE: Use with 23180 float switch. Ensure wiring connections remain above water level on all submersible bilge pumps and float switches.

Pumps - Bilge - TMC

Pumps - Low Profile Bilge - TMC

• Bilge pump designed for confined or tight spaces.

• Drains down as low as 10mm.

• Strainer can be rotated and cover can be removed for easy cleaning.

• Reverse polarity protection.

• Non-return valve to prevent back flow.

• Breather holes to prevent airlocks.

• Outlet port can be rotated for various installation orientations.

• Vertical or horizontal mounting.

• Auto version features a time delay to avoid cycling.

• CE Certified: Ignition Protected ISO 8846 & Bilge

Pumps & Plumbing

Pumps - Bilge - Auto Eye - TMC

• Auto eye series fully automatic bilge pump.

• Efficient long-life motor, with stainless steel shaft.

• High-impact durable plastic housing.

• Built-in electronic controlled read sensor system.

• No separate float switch is needed.

• No power is used until the pump turns on.

• Quick-release base strainer for easy cleaning.

• CE Certified: Ignition Protected ISO 8846 & Bilge Pump Std ISO 8849.

NOTE: Ensure wiring connections remain above water level on all submersible bilge pumps and float switches.

Pumps - Bilge 1000 GPH - Handy Pump with Handle - TMC

• Equipped with a handle for portability.

• For discharging bilge water, deck cleaning, or general water pumping applications.

• Snap-off base strainer for easy cleaning.

• Base must remain fully submerged for pump to operate.

• CE Certified: Ignition Protected ISO 8846 & Bilge Pump Std ISO 8849.

NOTE: Suitable for intermittent duty only.

Pumps - Bilge Auto - Relaxn

• Automatic pump with integral float switch.

• The pump turns on as the water level rises and automatically shuts off when water is removed.

• Ignition protection.

• 1 m wire length.

NOTE: Ensure wiring connections remain above water level on all

bilge pumps and float switches.

23187

23191

Float Switch & Guard - TMC

23224

x 92 x 32

• Combine with Shurflo® submersible bilge pumps for automatic operation.

• Can be direct mounted on the 232100, 232101 and 232102, or remote mounted with the 232104 232106 and 232108 Bilge Pumps

• Non-mercury mechanical switch.

• 0.9m tinned wire.

• CE Certified, Ignition Protected ISO 8849

NOTE: Ensure wiring connections remain above water level on all submersible bilge pumps and float switches.

• Combine with submersible bilge pump for automatic operation.

• Float switch is made of high impact plastic, ultrasonically welded together for permanent waterproof performance.

• Non-mercury mechanical switch.

• Clear plastic guard prevents debris from blocking switch and provides easy visual inspection.

• 0.9m tinned wire, fitted with eye terminals.

• Supplied with 2 mounting screws.

NOTE: Ensure wiring connections remain above water level on all submersible bilge pumps and float switches.

• Combine with submersible bilge pump for automatic

• Float switch is made of high impact plastic, ultrasonically

for

• Non-mercury mechanical switch.

• 0.9m tinned wire, fitted with eye terminals.

• Supplied with 2 mounting screws.

NOTE: Ensure wiring connections remain above water level on all submersible bilge pumps and float switches.

Float Switch - High Power -

• Combine with large submersible bilge pump for automatic operation.

• Float switch is made of high impact plastic, ultrasonically welded together for permanent waterproof performance.

• Built in electromagnetic reed switch.

• Mercury free.

• 0.9m tinned wire.

• Supplied with 2 mounting screws.

• CE Certified

NOTE: Ensure wiring connections remain above water level on all submersible bilge pumps and float switches.

Directly mounted on to bilge pump.

Float Switch - Shurflo®

Float Switch - TMC

23179

23181

Marine Toilets

Toilets - Electric - Standard - Small Bowl

• Electric marine toilet with small ceramic bowl.

• Available with or without a moulded plastic shroud to enhance aesthetics and ease of cleaning.

• Compact soft close plastic seat and cover.

• Strong motor and macerator unit for efficient flushing.

• Convenient push-button flush operation.

• Supplied complete with wired switch box unit.

• An outlet adaptor is supplied to increase hose size to 1-1/2" I.D. for installation as a replacement of an existing manual toilet.

• An inlet adaptor is supplied to reduce the hose size to 3/4"I.D. for installation as a replacement of common manual or older electric toilets.

• Supplied with both straight and elbow discharge ports.

• CE Certified: ISO 8846 Marine (Ignition Protected).

Toilets - Electric - Standard - Large Bowl

• Electric marine toilet with large ceramic bowl.

• Available with or without a moulded plastic shroud to enhance aesthetics and ease of cleaning.

• Soft close plastic seat and cover.

• Strong motor and macerator unit for efficient flushing.

• Convenient push-button flush operation.

• Supplied complete with wired switch box unit.

• An outlet adaptor is supplied to increase hose size to 1-1/2" I.D. for installation as a replacement of an existing manual toilet.

• An inlet adaptor is supplied to reduce the hose size to 3/4"I.D. for installation as a replacement of common manual or older electric toilets.

• Supplied with both straight and elbow discharge ports

• CE Certified: ISO 8846 Marine (Ignition Protected).

Toilet - Electric - Dual Flush Control

• For use with TMC Electric Standard and Luxury Toilets.

• One touch control panel.

• Built-in micro IC control system provides Two flush options:

◦ Half flush - last for 5 seconds flush and delivers 2 litres of water.

◦ Full flush - last for 10 seconds and delivers 4 litres of water.

• Equipped with splash proof seals.

• Built-in 40 amp Relay circuit loop protects against high current.

• Supplied with plastic box package of 6 replacement fuses.

/ 45043

450520 / 450522 450524 / 450526

Toilets

- Electric - Standard - Spare Parts

SPE190

SPE192

Toilet - Electric - Luxury - Small Bowl

• Luxury home style toilet, with small white vitreous china bowl.

• Soft close plastic seat and cover assembly.

• Strong motor and macerator unit for quiet efficient flushing.

• Push button flush operation.

• Supplied complete with wired switch box unit and outlet hose joiner.

• An outlet adaptor is supplied to increase hose size to 1-1/2" I.D. for installation as a replacement of an existing manual toilet.

• An inlet adaptor is supplied to increase the hose size to 1" I.D. if required.

• CE Certified: ISO 8846 (Ignition Protected).

• Luxury Skirted toilet, with medium white vitreous china bowl.

• Soft close plastic seat and cover assembly.

• Strong motor and macerator unit for quiet efficient flushing.

• Push button flush operation.

• Supplied complete with wired switch box unit and outlet hose joiner.

• An outlet adaptor is supplied to increase hose size to 1-1/2" I.D. for installation as a replacement of an existing manual toilet.

• An inlet adaptor is supplied to increase the hose size to 1" I.D. if required.

• CE Certified: ISO 8846 (Ignition Protected).

• Luxury home style toilet, with large white vitreous china bowl.

• Soft close plastic seat and cover assembly.

• Strong motor and macerator unit for quiet efficient flushing.

• Push button flush operation.

• Supplied complete with wired switch box unit and outlet hose joiner.

• An outlet adaptor is supplied to increase hose size to 1-1/2" I.D. for installation as a replacement of an existing manual toilet.

• An inlet adaptor is supplied to increase the hose size to 1" I.D. if required.

• CE Certified: ISO 8846 (Ignition Protected).

Toilets - Electric - Luxury - Large Bowl

Toilet - Luxury - Spare Parts

SPE196

SPE190

SPE192

Toilets - Electric - Quiet Operation - Small Bowl

• Deluxe electric marine toilet with quiet operation diaphragm pump and small, skirted ceramic bowl.

• Plastic soft-close seat and cover assembly.

• Intake rinse pump and strainer can be remote mounted to supply sea or fresh water for quiet flushing.

• 4-way flush control panel included:

• Eco flush • Full flush

Water only

Toilets - Electric - Quiet Operation - Medium Bowl

• Deluxe electric marine toilet with quiet operation diaphragm pump and medium, skirted ceramic bowl.

• Plastic soft-close seat and cover assembly.

• Intake rinse pump and strainer can be remote mounted to supply sea or fresh water for quiet flushing.

• 4-way flush control panel included:

• Eco flush • Full flush • Water only

•

Toilets - Electric - Quiet Operation - Large Bowl

•

• Intake rinse pump and strainer can be remote mounted to supply sea or fresh water for quiet flushing.

• 4-way flush control panel included: • Eco flush • Full flush

Water only

Empty only • CE Certified: ISO 8846 (Ignition Protected).

Toilets Inlet Rinse Pump - Raw Water

• Replacement flush pump for TMC Quiet Operation Toilets.

• 4-chamber diaphragm design

• Supplies raw sea, or fresh water for flushing.

• Built-in check valve prevents backflow.

• Snap-in port fittings - 3/4" I.D. hose barb and 3/4" BSPM included.

• Built-in thermal overload protection, self-priming and can be run dry.

• CE Certified, Ignition Protected ISO 8846.

Toilets - Electric - Quiet Operation - Spare Parts

Electric Toilet Spares

Toilet - TMC Electric Quiet Operation - 4-Way Electric Flush Control Panel

• TMC 4-Way flush control panel with smart touch controls suits Quiet Operation Electric toilets.

• Complete with control panel, control box, cable & connectors.

• Electronic control box can be installed remotely.

• Pre wired connections.

4-Way Touch Control Functions: Eco-Flush

• Press to start timed flush cycle.

• Inlet pump will run for 5 seconds pumping 1.35 litres of water and will flush for approximately 3 seconds.

Full Flush

• Press to start timed flush cycle.

• Inlet pump will run for 10 seconds pumping 2.7 litres of water and will flush for approximately 6 seconds.

Water Only

• Press to add water to bowl using 1.35 litres of water and runs for approximately 5 seconds.

Empty Only

• Press to empty bowl (flushes for approximately 3 seconds).

Matro Toilets, Spares & Accessories

3 Buttons Control Panel

• Matromarine 3 Button Control Panel is equipped with a programmed microprocessor having 3 options:-

• Before Use: Prepares the bowl with a water coat to prevent waste adhesion.

• Short Use: Saves water with a quick flush.

• After Use: Initiates a thorough flush, leaving the bowl clean and ready.

• Includes LED holding tank indicator lights - ON/EMPTY - 3/4 - FULL.

• Suits 12V/24V.

• Converts the bowl of most common toilets with 4 bolt fixing bowls with centres on a 95mm (3-3/4") diameter.

• Suits Matromarine, Jabsco, TMC, Raritan, RM69, Johnson Pumps and Thetford.

• Includes 3 button flush control panel with LED holding tank level indicators (sensor not included).

• Kit contains stainless steel bolts and washers, hose tails and gaskets.

• Requires connection to a separate inlet pump, such as 453091/453092

• Replaces base on Matro compact, comfort and deluxe bowl toilets.

• Waste Tank Sender Unit suits 453060.

• Two switch points - Three quarter full at 170mm and full at 60mm from top of tank.

Toilet Base Conversion Kit - Matro Silent Flush

Hydrovacuum Toilets, Spares & Accessories

Electric Toilets - Matro Silent Flush - Luxury Bowl

• Diaphragm type pump.

• Includes water filter with 3/4" tails.

• Made in Italy.

• Used to connect an electrical toilet to the vessel's

• Plastic Body with 1/2" BSPF ports.

• Pressure Range - 0 to 6 Bar.

• Italian designed and crafted vitreous white porcelain bowl with soft close plastic seat and lid.

• Standard luxury bowl model (455mm height).

• Hydrovacuum system with vortex style pump.

• Easy to install either above or below sea level.

• Low water consumption (approximately 1 - 2.5 litres).

• Quiet operation.

• Includes 3 button flush control panel with LED holding tank level indicators (sensor not included).

• Requires separate inlet pump or connection to vessel's water pressure system via a solenoid valve.

• CE Certified, ISO 8846, EN 55014.

• Replacement vortex style vacuum motor kits to suit Matro luxury bowl silent flush toilets.

• The Aqualarm System provides early warning when the black water holding tank is nearly full. The system is comprised of a panel indicator and sensor switch.

• The Aqualarm System is designed to operate on 12 or 24 volt DC.

• Tank Sensor Switch distance from under gasket or top of tank to bottom of float 95mm.

• Stainless Steel fastenings, internal wire tinned against corrosion.

• Panel Size 90 x 50mm.

NOTE: DO NOT use in fuel tank.

453043 / 453044

Matro Luxury Bowl Vacuum Motor Kits

Toilet - Portable Chemical

• The portable toilet is ideal where sewage is not permitted to be discharged overboard.

• High-density polyethylene tank.

• ABS seat and cover.

• Reliable bellow flush pump for simple operation.

• Detachable waste tank for easy disposal of waste into domestic toilet or sewage collection point.

Waste Tanks - Side Mount

45260 Replacement 90° Elbow Stepped Inlet or Outlet Tail suit 1-1/2" / 2" I.D. Hose

45271 Straight Stepped Nylon Breather Tail suit 5/8" / 3/4" I.D. Hose

• Side mount tank moulded from black polyethylene with recess at one end for hose connections.

Waste Tanks

• Flexible black/grey waste tanks which conform to irregular shapes.

• Thermoplastic elastomer "plastic rubber" construction.

• Choice of rectangular or triangular shapes.

• Fitting kit includes stepped 90° elbow, inlet and outlet tails to suit 1-1/2" or 2" I.D. hose and stepped straight breather hose tail to suit 5/8" or 3/4" I.D. hose.

• Suitable for Grey or Black Waste.

• Lightweight and sturdy.

• When mounted with the recess on the right hand side, the lower hose connections is fixed stepped hose barb suitable for 1" / 1-1/2" / 2" I.D. hose and the upper hose connections is a 1-1/2" BSPM thread.

• A 45260 fitting kit is supplied including 1-1/2" BSPF x 1-1/2" BSPM elbow coupling and a 1-1/2" BSPF x 2" / 1-1/2" stepped hose tail providing multiple connections options.

• 3/8" BSPF threaded ports are fitted and blanked at top and bottom of the main tank to facilitate connection of a breather depending which way the tank is mounted.

Replacement Clear Screw-in Lid & Gasket

• Vertical tank with see-through inspection cap at 3/4 full level.

• Suitable for Grey or Black Waste.

• Moulded from high density yellow Polyethylene.

• Lightweight and sturdy.

• Complete with inlet and outlet fittings to suit 1-1/2" I.D. which can be installed in suitable positions in the top, bottom or side of the tank.

• Also supplied with breather outlet fitting to suit 1" I.D. hose.

45041R

45021

Waste Tanks - Vertical

Waste Tanks - Flexible

Connectors included with each tank

45260

Connectors included with each tank

45271

Fitting included with each tank

• Ideal solution for holding tanks on smaller boats and conversion of existing overboard discharge systems.

• Suitable for Grey or Black Waste.

• Moulded from high density yellow polyethylene.

• Lightweight and sturdy.

• Includes removable inspection port.

• Supplied complete with fitting kit including - 1-1/2" BSPF swivel inlet and outlet hose tails with a choice of straight or 90° elbow connection, 1-1/2" BSPF cap for secondary discharge port, 1-1/4" BSPM plug for level sender port and 3/8" x 5/8" I.D. straight stainless steel breather hose tail. A 3/8" BSPM x 3/8" BSPF stainless steel elbow coupling is also included for 90° connections to the breather..

Note: Add 80mm height for swivel inlet and outlet tails.

Waste Tanks & Accessories

• Black/grey waste tank system, complete with overboard discharge pump.

• Moulded from high density yellow polyethylene.

• Supplied complete with Jabsco self priming diaphragm type 12V pump with 1-1/2" I.D. hose outlet, mounted in a recess to reduce overall height.

• Supplied with level sender and gauge.

• Fitting kit includes 1-1/2" BSPF swivel 90° elbow inlet hose tail 1-1/2" BSPF cap for secondary discharge port, 3/8" BSPM x 3/4" I.D. stainless steel elbow breather hose tail, carbon filter and white nylon breather to suit 3/4" I.D. hose.

• A vented loop with stepped hose tail is also provided for fitting in the discharge hose.

NOTE: Add 110mm height for installation clearance.

Waste Tank Gauges

• Double layer reinforced anti-fogging lens.

• Supplied with plug-in wiring harness (100mm).

• Waterproof rating of IP67.

• CE Certified.

Waste Tank Senders - 1-1/4" BSPM

• Stainless steel.

• Mount Flange: 54mm.

• Mount Style: 1-1/4 in BSP

• Rubber gasket and stainless steel screws included.

• This waste tank LED Gauge and sender kit is used to sense and display the level of waste within a vessels waste tank.

• 3 LED display indicator - On-High-Full.

• 316G stainless steel sender with 1-1/4" BSPM thread.

• Mounting O-ring: 38mm x 2.6mm. 43mm x 3.5mm.

• Sender cable: 400mm tinned with PVC cover.

NOTE: Refer to page 366 for mounting flange options for 1-1/4" BSPM senders.

• Sensor switch for black/grey waste tanks indicates when the tank is near capacity.

• Used to activate a warning light or buzzer.

• 1" BSPM thread.

• Stainless steel.

• Mount Flange: 83mm

• Mount Style: 6 Hole.

• Rubber gasket and stainless steel screws included.

Vented Loops - Nylon - TruDesign®

• Glass reinforced nylon composite.

• Commonly used on toilet installations where the bowl is below or close to the waterline, particularly on yachts when heeled.

• Mounted at the top of a loop in the hose, well above the waterline at all times.

• Valve opens when pumping of water ceases allowing air to enter the inlet and outlet hoses, preventing syphoning of water back through the bowl.

• Replacement cap and valve assembly are available.

• For more detail see TruDesign® Vented Loops on page 111.

Vented Loops - Solenoids Valve - TruDesign®

• Glass reinforced nylon composite.

• Commonly used in electrical toilet installations where the bowl is below the waterline, preventing syphoning of water back through the bowl.

• For more detail see TruDesign® Electric Solenoids Vented Loops on page 111

/

Vented Loops

Vented Loops - Nylon

• Moulded in white nylon.

• Designed to prevent syphoning of water when mounted well above the waterline, at the top of a loop in the inlet and outlet hoses of a toilet.

• 3 screw mounting points on the 1" and 1-1/2"vented loop and a single screw mounting point on the 3/4"vented loop for installation to a bulkhead.

Vented Loop - Stainless Steel

• High quality stainless steel tube with brass valve.

• Commonly used in electric toilets installations where the toilet bowl is below the waterline, particularly on yachts when heeled.

• 2 screw mounting points give secure and easy installation to a bulkhead.

• Constant internal diameter - No reduction in flow or collection of waste.

Loop - Stepped Tails

• Anti Syphon Loop with Valve, most commonly used in black waste systems where the toilet bowl is situated below the waterline at any time.

• Stepped ports cater for internal hose diameters of 1/2", 5/8", 3/4", 7/8", 1", 1-1/8", 1-1/4" and 1-1/2".

• Smaller ports are cut of when not required.

• Width 158mm x Height 280mm with 2 bulkhead mounting holes.

45452

Vented

Carbon Filters, Diverter Valves & Accessories

Tank - Carbon Filter - Vent

Aquavalve - Diverter - TruDesign®

• This innovative design simplifies Black Water and Fuel Vent maintenance without needing to replace the entire unit.

• Active Carbon Filter is ideal for Black Water and Fuel vents.

• Transparent screw-on lid for easy inspection and provides Quick access for changing the Carbon filter cartridge.

• Detachable mounting bracket.

• Stepped tail suits hose diameters: Ø 3/4" and Ø 1" I.D.

• 458904 - Includes housing, Active Carbon Filter Cartridge and mounting bracket.

• 458908 - Replacement Carbon Filter Cartridge only.

(PC) lense for easy inspection

(PP)

Waste Tank - Carbon Filter

• Essential addition to a waste or holding tank vent pipe reduce the odour.

• Contains active carbon.

• Two brackets supplied for easy mounting to a bulkhead.

• Clear bottom enables inspection to ensure fluid has not entered filter.

• Stepped tail to suit 3/4"/ 1" I.D hose.

• Length 200mm x Ø 50mm.

• Most commonly used in a black waste discharge system to select evacuation to holding tank or overboard.

• Glass reinforced nylon composite.

• Bulkhead mounted.

• Ports are 1-1/2" BSPF.

• Specific short 1-1/2" BSPM Aquavalve tails are available in straight, 90° and 120° to suit 3/4", 1", 1-1/2" I.D. hose.

• Other accessories such as nipples and plugs are also available.

• For more detail see Aquavalve 3 Way Diverting Valves on page 109

Aquavalve - Threaded Nipple

• Glass reinforced nylon composite.

• Nipple with short thread on one side to suit TruDesign Aquavalves.

• Commonly used to connect the Aquavalve to rigid pipe.

• Immune to corrosion and electrolysis.

• UV resistant.

• Screws into compatible

• Glass reinforced nylon composite.

• Spanner to tighten TruDesign® Aquavalve hose tails to a maximum torque of 16Nm (12ft/lbs)

458904

458908

Diverter Valves & Accessories

Aquavalve Hose Tails - Straight

• Glass reinforced nylon composite.

• Straight Tails with short thread to suit TruDesign Aquavalves and the most common sizes of hose used in marine toilet plumbing.

Aquavalve Hose Tails - Angled

• Glass reinforced nylon composite.

• Angled Tails with short thread to suit TruDesign Aquavalves most common sizes of hose used in marine toilet plumbing.

• Tails include a Blue Seal to allow fitting to be rotated to a more suitable position if required.

Aquavalve - Hidden Bulkhead Diverter

Aquavalve 3 Way Hidden Bulkhead Mount 49 White 45347 Through Bulkhead Extension suit 45303

• Hidden, behind bulkhead version of traditional Aquavalve allows the valve mechanism and hose to be concealed behind a bulkhead with only the activation handle and face plate visible.

• Suits bulkheads up to 20mm thick.

• Additional 45347 through bulkhead extension maybe added to suit bulkheads up to 40mm thick.

• Part are 1-1/2" BSPF and accept all Aquavalve tails, nipples and plugs.

• For more detail see Aquavalve 3 Way Diverter Valves on page 109

Threaded Reducing Breather Plug

453270 3/4" BSPF 1-1/2" BSPM White

• Threaded plug used to reduce the common 1-1/2" BSPF threaded ports in waste holding tanks to 3/4" BSPF to accept a breather tail.

Diverter Valves - Y

45456 Nylon 'Y' Diverter Valve 1"

45457 Nylon 'Y' Diverter Valve 1-1/2"

• 'Y' Diverter Valves commonly used on waste discharge systems to select one or the other destination.

• Can also facilitate one pump to draw from two separate compartments but not both at the same time.

• Bulkhead mounted.

• Moulded nylon.

• Glass reinforced nylon composite.

• Short threaded plug to suit TruDesign Aquavalves.

• Used to block one port when parts of the system are not yet installed, or maintenance is being completed and the system still needs to be used.

• Barbed ports.

Black Waste Pumps

Pumps - Macerator - Shurflo®

SP-260 Replacement Impeller Kit

SP-261 Replacement Macerator Impeller Housing Kit

• Designed for black waste evacuations.

• SHURflo’s Macerator pump features a premium impeller design with rundry capability and includes a seamless shell motor with O-ring sealed bell end and a sealed manual turn key.

• Self-priming up to 1.2 metres.

• Unique dual blade and housing construction ensures problem free pumping, and superior performance.

• Thermally Protected, CE Certified, Ignition Protected ISO 8846.

• Port Size: Inlet: 1-1/2" Barb / 1-1/2" NPT Outlet: 1" Barb.

• RCM Certified to Australian Standards.

• Designed to pump waste into or to empty marine and RV holding tanks.

• Macerates and discharges black and grey water and waste mixtures.

• Flexible impeller type pump.

• Self-priming (Do not run dry).

• Dual-cut metal blade grinds waste.

• Inlet Port: 1-1/2" BSPM or 1-1/2" I.D. hose tail.

• Outlet Port: 1" I.D. hose tail.

• Delivery head 5m (16ft).

• CE Certified ISO-9001 and ISO-14001.

Pumps - Black Water - Diaphragm - TMC

• Single diaphragm pump for unmacerated black waste mixed with water.

• Self-priming pump can be run dry.

• Non-choke valve, no filter required.

• Can pump a mixture of air and water.

• Aligned inlet and outlet valves to allow free flow of debris.

• Adjustable clamping ring allows the head assembly to be rotated 360° to accommodate plumbing position.

• CE Certified, ISO-9001 and ISO-14001.

• Port Size: Inlet: 1-1/2" Outlet 1-1/2"

Repair Kit - Diaphragm - Waste Pump

Diaphragm Waste Pump Repair Kit

• Kit includes diaphragm and 2 x valves.

• Suits TMC grey waste or black waste Diaphragm pumps.

SP189

Pump - Macerator - TMC®

Pumps - Grey Water - Diaphragm - TMC

• Single diaphragm pump suitable for galley or shower grey waste applications.

• Also suitable for bilge pumping.

• Self-priming pump can be run dry.

• Non-choke valve, no filter required.

• Can pump a mixture of air and water.

• Aligned inlet and outlet valves to allow free flow of debris.

• Adjustable clamping ring allows the head assembly to be rotated 360° to accommodate plumbing position.

• CE Certified, ISO-9001 and ISO-14001.

• Port Size: Inlet: 3/4" Outlet 3/4"

Pumps - Diaphragm - Matromarine®

• Diaphragm pump, suitable for bilge or grey waste transfer.

• Pump is self priming up to 2m vertical lift.

• Pump base and motor support are made of nylon, and the pumping movement is run on ball bearings.

• Pump can run dry for longer periods without suffering any damage.

• Supplied complete with a inline filter.

• CE Certified, Thermal and Ignition Protected ISO 8846.

• Grey Waste Manifold used to collect grey water from multiple sources with different size outlets.

• Feeds into holding tank and/or discharge pump via 1-1/2" BSPM threaded outlet.

• Hose diameters include 1/2", 5/8", 3/4", 7/8", 1", 1-1/8", 1-1/4", and 1-1/2".

• Ports are cut open as required.

Grey Waste Pumps & Sump Boxes

Grey Waste Sump Box - Can-SB

• Grey waste sump for connection to a remote pump.

• Equipped with a level sensor switch with a delay shutdown to allow total emptying of liquids remaining in pipe.

• Removable mesh filter allows easy cleaning.

• Inlet Port Sizes: 4 x 1", 2 x 3/4"

• Outlet Port Size: 2 x 3/4"

• Automatic pump - no additional float switch required.

• The pump turns on as the water level rises and automatically shuts off when water is removed.

• Removable mesh filter allows easy cleaning.

• Clear clip-on cover provides easy inspection.

• Equipped with a check valve on the outlet to prevent back flow.

• Manages grey water from multiple sources.

• Simple installation.

• Ignition protection.

• 1m wire length.

• Inlet Port Sizes: 3/4", 1", 1-1/8", 1-1/2"

• Outlet Port Size: 3/4"

Lid

• Centralises grey waste from showers, basins and sinks.

• Clear hinged lid for inspection and cleaning of filter.

• Manifold has three inlets: 3/4", 3/4" / 1" and 1-1/8" / 1-1/2".

• Outlet Port Size: 3/4" / 1"

NOTE: Pump & switch not included.

Grey Waste Sump Box with Clear

Grey Waste Sump & Pump System

Rotate ports to

Waste Manifold

General Purpose Hoses

NOTE: Only larger sizes available in cut lengths. Not suitable for permanent petrol fuel lines. Hose - PVC - CMP Braided Per Roll & P/M

• Translucent braided PVC pressure hose that can be used for air, water, petrol & food contact. Rated up to 230 PSI.

• Meets AS2070 Australian Standard.

Hose - Clear Vinyl Tubing

Per Roll & P/M

• Suitable for food and beverage contact as well as low pressure general purpose delivery.

• Meets the AS2070 Australian Standard food contact requirements.

NOTE: Only larger sizes available in cut lengths.

General Purpose, Grey Water & Bilge Pump Hoses

Hose - Clear PVC - Spring Reinforced Per Roll

• High life cycle with durability and performance

• Particularly effective in low temperature environments.

• Ideal for supplying water or oil based liquids and is chemical resistant.

• Super transparent body to easily identity blockages.

• Shock resistant, moderately flexible, kink and crush resistant.

• Supplied in Rolls (No cut lengths).

NOTE: Not recommended for drinking water.

• Marine/RV Flexible hose is suitable for supplying water, oil based liquids and chemical agents.

• Commonly used for bilge pumping and grey waste transfer.

• Light weight, flexible, kink and crush resistance.

• Working pressure: 28 psi.

• Supplied in Rolls (No cut lengths).

NOTE: Not recommended for drinking water.

• Ideal for bilge pumps, live well systems, and as a waste hose for caravans or RVs.

• Smooth bore reduces friction loss and residue build-up.

• Smooth outer provides secure clamp fit for superior sealing.

• Excellent flexibility and UV stability.

• Operating temperature: 5°C to +60°C.

• Max pressure 60 psi.

Hose - Smooth Bore - Ribbed Outer

Hose - Sanitation - Nylon Reinforced Per Roll

• Smooth bore white PVC hose.

• Extremely flexible, designed for marine toilets.

• Impact and crush resistant.

• Weather and most chemical resistant.

• Working pressure: 100 psi.

• Supplied in Rolls (No cut lengths).

Hose - Sanitation - Steel Reinforced

• Smooth bore white PVC hose.

• Extremely flexible, designed for marine toilets.

• Limits the spread of odours from toilets and drains.

• Impact and crush resistant steel wire helix reinforcement.

• Weather and most chemical resistant cover.

• Temperature range: -15°C +60°C.

• Working pressure: 75 psi (3/4" & 1") 60 psi (1-1/2").

• Made in Italy.

Hose - Sanitation - Rubutyl - Premium

• Flexible, strong anti-odour rubber hose designed for marine toilets systems.

• Temperature range: 40°C - 120°C.

• Working pressure: 105 psi.

• Made of special butyl compound which prevents odour spread and bacteria growth.

• Resistant to all detergents and disinfectants.

• Very flexible and easy to install.

• Made in Italy.

Hose - HD Washdown - Sanitation

• White pressure hose - reinforced smooth bore.

• Ideal for marine toilet installations.

• Also suitable for a washdown hose.

• Available in 20m rolls and per metre in 1-1/2"

Washdown, Drinking Water & Ventilation Hose

Hose - PVC Washdown

• Lightweight hose ideal for on board or marina washdown.

• White with blue stripe, super flexible water delivery hose.

• Non-marking.

• Sold per roll. No cut lengths available except for 1-1/4" size.

NOTE: Not recommended for drinking water.

Hose - Drinking Water Food Grade

• Marine and RV drinking water hose made from food grade polyethylene to comply with NSF food grade international certification.

• 76302 includes 3/4" and 1" Nylon quick connect fittings (BSP).

• 76304 includes 3/4" and 1" Brass quick connect fittings (BSP).

NOTE: Hose sold in rolls only (No cut lengths available).

• Suitable for venting bilge gases or general air flow.

• Flame resistant flexible PVC ducting.

• UV resistant.

• Wire reinforced.

DMfit® Push-In Tube Fittings - 12mm Range

Connector Straight BSPPM x 12mm Tube

Connector Elbow Swivel BSPPM x 12mm Tube

Connector Straight BSPTM x 12mm Tube

• BSP tapered thread.

Connector Elbow Swivel BSPTM x 12mm Tube

Connector Elbow BSPTM - 12mm Tube

Connector 'L' Swivel BSPPM - 12mm Tube

Connector Tee Swivel BSPPM - 12mm Tube

Connector Straight BSPPF - 12mm Tube

DMfit® Push-In Tube Fittings - 12mm Range

Two configuration options:

• Inlet at A.

- Flows to B+C.

- Shut off B only.

• Inlet at B.

- Flows to A+C.

- Shut off A+C.

Scan QR code for configuration options.

•

DMfit® & Twistloc Fittings to suit 12mm Tubing

Connector Straight BSPPM x 12mm Tube

• Nickel plated brass.

• BSP parallel thread with O-ring seal.

Connector Elbow BSPPM x 12mm Tube

• Nickel plated brass and acetal.

• BSP parallel thread with O-ring seal.

Connector Straight BSPPF x 12mm Tube - Brass

• Nickel plated brass.

• BSP parallel thread.

Thread Adaptor BSPPF 1/2" x 3/8"

• Nickel plated brass.

• BSP parallel thread.

• Tube working pressure 170 psi.

• Operating temperature - Air -20°C ~ 65°C Liquid.

• Compliant to ANSI/NSF-51, 61, WRAS and FDA requirements for food contact applications.

NOTE: Pressure values are based on PE tube used at room temperature.

Tube Mounting Clips - 12mm

• Tube mounting clips to keep your plumbing tidy and secure.

• Supplied in a strip of 10 Clips.

• Can be separated into single mounts.

• Fixed with 2 x 6g c/s screws.

Flow Bend Clip - 12mm Tube

• Ensures bends in tube retain full flow.

DMfit® Push-In Tube Fittings - 15mm Range

Connector Elbow Swivel BSPPM - 15mm Tube

Connector Straight BSPPF - 15mm Tube

Connector Straight BSPPF - 15mm Tube - Brass

Connector Elbow Swivel BSPPF - 15mm Tube

• BSP parallel thread with O-ring

Connector Straight BSPTM - 15mm Tube

Connector Straight BSPPM - 15mm Tube Elbow Swivel BSPPF - 15mm Tube - Brass

Connector Elbow BSPTM - 15mm Tube

•

Connector Straight Swivel BSPPF - 15mm Tube

• BSP parallel thread with O-ring seal.

Connector Straight - 15mm Tube x Hose Barb

DMfit® Push-In Tube Fittings - 15mm Range

DMfit® & Twistloc Push-In Tube Fittings - 15mm Range

Tube LLDPE - 15mm

• Tube working pressure 170 psi.

• Operating temperature - Air -20°C ~ 65°C Liquid.

• Compliant to ANSI/NSF-51, 61, WRAS and FDA requirements for food contact applications.

NOTE: Pressure values are based on PE tube used at room temperature.

Mounting Clip - Locking - 15mm Tube

Flow Bend Clip - 15mm Tube

Pipe - PEX Watermarked - Twistloc

• Certified to BS7291 class S and DIN16892.

• Some States or Territories require the use of Watermark Pipe in hot water installations. Please refer to your certified plumbing contractor for applicable legislative requirements.

Tube Cutter - 12mm

• Suitable for cutting plastic tubing sizes up to 13mm.

• High quality blade for longevity.

Connector

Twistloc Push-In Tube Fittings - 22mm Range

Connector

Twistloc 22mm Tube, Fittings & Manifolds

22mm

• Manifolds are supplied with both

cap and handle covers.

• Part number 449786 divider plug is required to separate hot and cold water supply (not included).

• Certified to BS7291 class S and DIN16892.

• Some States or Territories require the use of Watermark Pipe in hot water installations. Please refer to your certified plumbing contractor for applicable legislative requirements.

Manifold Dual Open Type 28mm Tube Inlet 15mm Tube Outlet

• Manifolds are supplied with both blue (cold) and red (hot) valve cap and handle covers.

• Part number 449786 divider plug (not included) is required to separate hot and cold water supply within each branch if configured in that manner.

• Clip-in bracket designed to be securely located into a recess with notches on each end fitting to a manifold. Manifold Bracket - Plastic

• Used to label manifold branches.

• Heavy duty 2 mm thick 316G Stainless Steel Plate, folded and fabricated to provide secure mounting of single row, 3, 4 or 6 manifolds.

• Stainless Steel clamps locate into recesses at each end of the manifold.

Bracket shown with Manifold

Manifold Bracket - Stainless Steel

•

Bathroom, Shower & Laundry Fittings Bathroom Accessories & Coat Hooks

•

•

•

Shower Kit - DuoFlo Sprayer & Hose Kit

• Smooth rotating head enables selection between two different flow patterns including shower or direct spray.

• Textured rubberized grip, ABS housing and brass internals.

• Two flow strengths adjustment with a light or firm press.

• Single hand intuitive smooth operation.

• Solid brass interior prevents any corrosion.

• Shower kit includes sprayer head, holder, hose and mesh bag.

• Horizontal or vertical mounting options for any application.

• Pressure range up to 100 PSI.

• Stylish 316G stainless bezel hides mounting screws and provides a high-end fit and finished look.

NOTE: Cold water application only.

• Recess installation shower box in ABS with shower in chromed brass.

• Round shower box with lid, hose and push button shower head.

• Hose length 2.5m.

• Connection 1/2" BSPF thread hose.

• Foldaway handle on shower head.

• Made in Italy.

Shower Box - Mixer, Hose & Head Kit - Lockable

51070LW Replacement Lid & Key To suit 51070

51070L Replacement Lid To suit 51070

• Compact shower box and hot and cold mixer with hose and nozzle

• Includes lockable or non-lockable lid with spare key

• Recess mount installation.

• PVC chrome/white 1.6m hose.

• Connection 3/8" BSP (Female) thread hose at mixer.

• Made in Italy.

Mount

Mount DuoFlo Sprayer

Stainless Steel Hose

Mesh Bag For Hose

Shower Box - Hose & Head Kit

Elbow Sprayer with 8ft S/S Hose

Transom Shower with 8ft S/S Hose & Box

• Elbow Spray head with chrome plated brass housing.

• Constant-On lock or push and release water flow options.

• Includes sprayer head, 8ft stainless steel hose and thru-surface holder for horizontal mounting.

• Corrosion resistant.

• Meet CASS 44 salt spray requirements for exterior use.

Shower Box - Short Hose & Head Kit

•

• 1.2m

• Hose connection 3/8" BSP thread.

•

•

•

•

• Highly polished 316G stainless steel lid with black plastic holder.

• Shower head is solid brass with chrome finish for extra durability.

• Lid includes stop point to prevent it from resting on the gelcoat surface when open.

• Constant-On lock or push and release water flow options.

• Shower kit includes sprayer head, box, hose and mesh bag.

• Vertical or horizontal mounting.

• The hose is stored behind the stainless steel lid in its own mesh bag to keep it clean and snag free.

Shower Head -

Compact

•

• Shower head with CONTINUOUS ON / OFF push button flow control and shower spray / tap flow nozzle.

• Connection 1/2" BSPM thread.

• Made in Italy.

Shower Kits, Boxes & Faucets

Shower Box - Hinged Lid

51067 Round Hand Shower Box suits 51010 Shower Head

• Fits almost any size shower head and angle.

• Made in Italy.

• Shower head not included.

• Complete with soft cap.

• Cutout ø 60mm.

- Twin Mixer - Chrome Handles

Twin Mixer with Chrome Handles Only

• Chrome Plated Brass (CPB) mixer.

• Connections 3/8" BSPM thread for hoses with shower head.

• 19mm installation holes.

• Made in Italy.

- Twin Mixer - Faucet Shower Box - Soft Lid

- Twin Mixer - Clear Handles

• Chrome Plated Brass (CPB) mixer.

• Connections 3/8" BSPM thread for hoses with shower head.

• 19mm installation holes.

• Made in Italy.

Shower Box - Chrome

Chrome Shower Box - Round

• Chrome finish shower box.

• Shower head not included.

Twin Mixer & Faucet 3/8" BSPM 3/8"

• Chrome Plated Brass (CPB) compact mechanic mixer with folding pipe 10mm. Height 200mm.

• Connections 3/8" BSPM thread.

• Made in Italy.

Tap - Washdown - Faucet - Stainless Steel

Tap - Laundry - Faucet

• Chrome plated brass (CPB) laundry tap

• Compact design.

• Includes wall nut and rubber washers.

• Made in Italy.

- Flick Mixer - Pullout

51068 Replacement Ceramic Cartridge 35mm with 2 Nozzles

• Single lever mixer in brass with regulating spray on the shower head and 1.8m flex hose in nylon and plastic lever.

• Ceramic cartridge 35mm Ø.

• Connection 3/8" BSP (Female) thread hose.

• Made in Italy.

Tap - Flick Mixer - Short Faucet

Replacement Ceramic Cartridge 35mm with 2 Nozzles

• Single lever compact mixer in chrome plated brass (CPB) with short revolving faucet

• Connections 2 x 3/8" BSPM hoses.

• Ceramic cartridge Ø 35mm.

• Made in Italy.

51019WM 51019

Faucets

Tap - Flick Mixer - Long Faucet

51040 Flick Mixer Long Faucet 3/8" BSPM

51068 Replacement Ceramic Cartridge 35mm with 2 Nozzles

• Single lever mixer in chrome plated brass (CPB) with long revolving faucet

• Connections 2 x 3/8" BSP (Male) hoses.

• Ceramic cartridge Ø 35mm.

• Made in Italy.

Tap - Mixer Cartridge

51068 Ceramics Cartridge 35mm with 2 Nose

• Suits all Aravon® Flick Mixers.

• Made in Italy.

Tap - Connectors

Taps - Single - Faucet

• Single brass tap with left or right command and folding pipe 10mm.

• Supplied with red and blue inserts (hot and cold).

• Connection 3/8" BSPM thread.

• Made in Italy.

Tap - Single Folding - Faucet

• Brass compact single tap with lowering and folding faucet.

• Connection 3/8" BSP (Male) thread.

• Made in Italy.

Single Folding Tap & Faucet 3/8" BSP

Taps - Double Folding - Faucet

51052 Double Folding Tap & Faucet 3/8" BSPM

• Brass compact mixer taps with lowering and folding faucet.

• Connections 2 x 3/8" BSP (Male) thread.

•

Tap - Mixer Bulkhead CPB

51035 Mixer Bulkhead CPB 3/8" BSPM

• Brass compact mixer tap.

• Connections 2 x 3/8" BSP (Male) thread.

• Made in Italy.

51034 Compact Single Mixer 3/8" BSPM

51068 Replacement Ceramic Cartridge 35mm with 2 Nozzles

• Chrome Plated Brass (CPB) compact single mixer.

• Connection 3/8"BSPM thread.

• Ceramic cartridge Ø 35mm.

• Made in Italy.

Faucet - Telescopic with Shut Off Valve

51005 Faucet Telesscopic with Shut Off Valve 1/2" & 3/8"

• For use with foot operated galley pumps and non-pressurised electric galley pumps.

• Aluminium and plastic construction.

• Twist on/off nozzle head.

• Telescopic.

• Swivels 360 degree.

• Stepped hose barb suits 1/2" and 3/8" I.D. hose.

Hand Pump Tap 1/2"

• Uses 1/2" I.D. hose.

• Extend 95mm above the bench top.

• The spout extends 150mm from the centre line of the pump.

• The maximum bench thickness is 30mm.

• The distance from the bench top to the bottom of the hose barb is 180mm.

51068

Tap - Flick Mixer - Single

Tap - Hand Pump

Shower Hose Filters

Hose - Shower - 1/2" Conic BSPF x 1/2"BSPF Hose - Shower - 15x1mm Male x 3/8"BSPF

51008 Shower Hose 2.5 Mtr 1/2" Conic BSPF x 1/2"BSPF

• 2.5m PVC white/chrome hose.

• Suits traditional domestic faucets.

232128 Mounting Clip suit 232126 In-line Filter

• Ideal for all marine, RV and home filter applications.

Shower Hose 2.0Mtr 15x1mm Male x 3/8"BSPF

• 2.0m PVC white/chrome hose.

• Suits type 28N faucets no longer in production.

Hose - Shower - 1/2" Conic BSPF x 3/8"BSPF Adaptor - Shower Hose - 1/2" BSPF - 3/8" BSPF

51060 Shower Hose suits 51044 2.0Mtr 1/2" Conic BSPF x 3/8"BSPF

• 2.0m PVC white/chrome hose.

• Suits RV faucets.

• Nickel plated brass

• Water Washed Coconut Shell GAC Carbon increases filter efficiency.

• Improves taste and reduces chlorine and odour.

• Approved to meet industry standards.

- Fresh Water - Inline 1/4" NPTF Filter - Fresh Water - Inline 1/2" Barb

• Ideal for all marine, RV and home filter applications.

• Water washed coconut shell carbon increases filter efficiency.

• Improves taste and reduces chlorine & odour.

• Approved to meet industry standards.

• Filters up to 6,000 gallons.

• 2.5" x 11" (64 x 279mm) in-line filter with 1/2" (13mm) barb ends.

Filter - Marine & RV Quick Change Cartridge

232123 Filter Head Bracket Suits Quick Change

• Quick Change Filter Only.

• Ideal for all marine, RV and Home filter applications.

• Water Washed Coconut Shell Carbon increases filter efficiency.

• Improves taste and reduces chlorine and odour.

• Approved to meet industry standards.

Taps - Single - Fresh Water Filter Kit

• Ideal for all marine, RV and home filter applications.

• Water Washed Coconut Shell Carbon increases filter efficiency.

• The quick-connect filter head and bracket simplify installation and enable easy filter replacement.

• Improves taste and reduces chlorine and odour.

• Approved to meet industry standards.

Kit Includes:

• 1 x 1/4"quick connect filter head with built in bracket.

• 1 x Replaceable quick change filter.

• 1 x Faucet* with mounting fitting.

• 1 x 12mm Equal Tee.

• 1 x 12mm Stem to 8mm Tube.

• 1 x 5/16" Stem to 1/4" Tube.

• 1 x Tap Adaptor to suit 1/4" Tube.

• 1 x 1.5 metre x

• Mounting hardware.

• *Dimensions tap from sink level: H:210 x W: 180.

Strainers Water - Plastic

• Plastic Water Strainer with transparent lid for easy inspection.

• The housing is made of black Moplen with a Makralon transparent cover and incorporates a high-quality nylon filter.

• This innovative design simplifies maintenance by removing the need to replace the entire strainer.

• Quick-access lid for easy inspection and strainer cleaning.

Strainers Water - Plastic

• The unique concept behind this innovative design is to simplify filter maintenance without needing to replace the entire Strainer.

• Transparent lid for easy inspection.

• Quick access screw-off lid for cleaning strainer.

• Detachable mounting bracket for easy maintenance.

blue tubing is not included in the kit. For demonstration purposes only.

Sinks & Sink Wastes

Sinks

Sinks - With Lid & Folding Tap - Stainless Steel

• Elegantly designed round and rectangle sinks with folding tap and tempered glass cover which doubles as a work surface when closed.

• 304G stainless steel sink. Vitro ceramic glass cover with folding faucet.

• Sinks include a 1-1/4" 90° waste and plug.

• Made in Italy.

Sinks - Rectangle - Stainless Steel

• Sinks and washbasins

• Sinks include a 1-1/4" 90° waste and plug.

• 304 stainless steel.

• Made in Italy.

•

•

•

•

•

•

•

Sinks - Round - Stainless Steel

50702

Sink Wastes & Drains

Waste & Plug

• 1-1/4" Waste and Plug x 25/20mm hose tail suits all stainless steel sinks and basins.

• Polypropylene (PP) body, stainless steel drain griddle with rubber plug.

Sink Waste & Tails - 1-1/4" BSP

• Sinks Waste 1-1/4" BSPM thread connects to 1-1/4" BSPF x 1" (25mm) straight or elbow hose tail fittings.

• The sink waste features a Polypropylene (PP) body, stainless steel drain griddle with rubber plug.

Sink Waste Chrome Plated Flip Drain

• Replacement flip drain stopper with 90° elbow for compact spaces.

• Sleek chrome finish.

• Flip design eliminates need for pop-up assembly.

• Quick and easy installation.

• Includes three seal rings and solid brass nut for a secure, watertight fit.

• 61 mm flange fits sink holes 38–51 mm; 57 mm depth ideal for tight spaces.

Deck Drain - Flush Mount - S/S Fascia

• Moulded fibre reinforced Acetal with highly polished stainless steel.

• Drain face mounts flush.

• The centre cap is removable for easy cleaning.

• Spacers included for thinner floor thickness.

• Concave shape for improved draining.

Drain - Cockpit & Shower - Skin Fitting

• Moulded Nylon.

• Square Mesh to prevent large objects going down the drain.

• Drain has a 5.5mm domed face.

Skin Fittings - Tail - Nylon & Stainless Steel

Skin Fitting - 90° Tail - Nylon

Fittings

• Nylon thru-hull connection skin fitting and barb tail, 316G stainless steel trim plate.

• Skin fitting and tail is glass reinforced nylon composite.

• Fitting includes nut.

Skin Fitting - 90° Tail - Nylon & Stainless Steel

• Nylon thru-hull with 90° bend and barbed tail.

• Skin fitting includes nut.

Skin Fittings - Tail - Nylon

• Nylon thru-hull skin fitting with BSP thread and tail.

• UV resistant.

• Skin fitting includes nut.

• 90° nylon thru-hull connection skin fitting and barb tail, 316G stainless steel trim plate.

• Skin fitting and tail is glass reinforced nylon composite.

• Skin fitting includes nut.

Scupper Skin Fitting - Nylon & Stainless Steel

• Nylon thru-hull connection scupper skin fitting and barb tail

• 316G stainless steel trim plate.

• Skin fitting and tail is glass reinforced nylon composite.

• Fitting includes nut.

Skin Fitting - 90° Tail - Nylon - White

• Nylon thru-hull with 90° bend and barbed tail.

• Skin fitting includes nut.

• UV resistant.

Skin Fittings

Skin Fittings - Tail - Acetal

• Acetal thru-hull connection skin fitting with BSP thread and tail.

• For use with Ball Valves & Gate Valves.

• UV resistant.

• Skin fitting includes nut.

Skin Fitting - L-Head - Nylon

• White Nylon thru-hull connection skin fitting with BSP thread and stepped barb tail - 20/25 mm

• L-Head skin fitting include nut.

Skin Fittings - Thru-Hull - Bronze

• Bronze skin fitting.

• BSP thread.

• Skin fitting includes nut.

Skin Fittings - Tail - Nylon

• Nylon thru-hull connection skin fitting with BSP thread and barb tail.

• For use with Ball Valves & Gate Valves

• Skin fitting includes nut.

Skin Fittings - Thru-Hull Stainless Steel

• 316G stainless steel skin fitting.

• BSP thread.

• Skin fitting includes nut.

Skin Fittings - Tail - Stainless Steel

• Short length 316G stainless steel thru-hull connection skin fitting and barb tail.

• Flange is machined to fit hull and groove to retain bedding compound.

• For thin hull sections up to 5/8" maximum.

• Skin fitting includes nut.

Skin Fittings - 90° - Bulkhead Thru-Hull Tail

• Ideal for tight spots where hose is difficult to route without kinking.

• 90° through hulls or bulkhead tails.

• Durable nylon construction.

• 45465 stepped tail.

Hose Tail - Bulkhead - Straight

Skin Fittings & Strainers

Scoop / Strainers - Nylon - TruDesign®

• For more detail see TruDesign® Scoops and Strainers on page 111

Scoops - Stainless Steel - BSP

• 316G stainless steel.

• Skin fitting includes nut.

TruDesign® - Fittings

Superior Composite Thru-hull Solution for use Above or Below the Waterline

Suitable for underwater use, TruDesign® range of Skin Fittings are certified by the International Marine Certification Institute (IMCI) and Bureau VERITAS to ISO 9093-2. They also comply with ABYC H-27 when used in conjunction with the TruDesign® ABYC collar.

Designed and made in New Zealand, the Skin Fitting body and nut are moulded from a glass-reinforced nylon composite. High strength, highmodulus glass fibres provide dramatic strength, stiffness, toughness and dimensional stability. These properties allow a significant weight reduction over metallic fittings.

TruDesign® Skin Fittings eliminate the corrosion and electrical bonding problems associated with metallic fittings.

When used in below waterline applications, a Ball Valve should be directly connected for safety and compliance to relevant marine standards.

Skin Fitting - Domed

*Maximum Hull Thickness allowing 70% thread engagement into Ball Valve.

• Designed to be installed above or below the water line.

• Paintable with all types of anti-fouling including Coppercoat™.

• Glass reinforced nylon composite - High strength, stiffness and light weight. Compatible with all hull types – aluminium, steel, wood, composite & GRP hulls.

• Immune to corrosion and electrolysis for long service life.

• Chemical resistant - Impervious to diesel, petrol and antifouling paints.

• UV resistant, suitable for all marine environments.

• Large operating temperature range from -40°C to +110°C.

• Certified to ABYC H27, ISO 9001, IMCI ISO 9093-2 and Burea Veritas 27801/A0 standards.

• Meets ABYC H-27 Standard when installed in combination with TruDesign® Valves and Load Bearing Collars*.

Skin Fitting - Recessed

Skin Fitting - GRP Mould Plugs

• Makes a Pre-form recess in the layup stage of GRP hulls that fits exactly a TruDesign® approved Recessed Skin Fitting - Saves complex machining of bevelled edges in the GRP hull ideal for OEMs.

• Bevelled Edges are now part of the Gelcoat - The integrity of the hull is maintained, minimising wicking down end grain and delamination.

• �on-stick properties for easy-removal from the hull.

• Reversed text imprinted on the fibreglass (reading the correct way).

• Centre drill locator and gluing ‘channel’ for increased contact with the adhesive or sealant.

Skin Fittings Long - Domed

• Extra-long length designed for larger hull-thickness vessels.

• Fits TruDesign® Ball Valves and other parallel BSP threads.

• Certified to ABYC H27, ISO 9001, IMCI ISO 9093-2 and Burea Veritas 27801/A0 standards.

• Meets ABYC H-27 Standard when installed in combination with TruDesign® Valves and Load Bearing Collars*.

NOTE: Minimum hull thickness 33mm.

Skin Fittings - Installation Tools

TruDesign® - Skin Fittings

Skin Fittings with Tail

•

• Designed for

Mounting Bracket For Ball Valves

• Designed to be installed above the water line only.

• Long hose tail (40mm) can be fitted with 2 hose clamps for a secure connection.

• Certified to ABYC H27, ISO 9001, IMCI ISO 9093-2 and Burea Veritas 27801/A0 standards.

NOTE: Skin Fittings with Tail are not approved for below water applications or below the heal line. For below the water line only use a Skin Fitting with Ball Valve attached (Seacock).

Ball Valve Spanners

• Spanner for tightening TruDesign® Ball Valves to a maximum of 16mm (12ft/lbs).

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• Chemical resistant - Impervious to diesel, petrol and antifouling paints.

• UV resistant, suitable for all marine environments.

TruDesign® - Ball Valves & Accessories

• Allows remote monitoring of up to four Ball Valves ( 450090 Display Panel) in the open or closed position.

• Can be wired into or part of an engine or generator start "interlock" to ensure they don’t start without cooling water available.

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• UV resistant, suitable for all marine environments.

• The ball and sealing rings utilise a PTFE polymer to ensure a smooth action and minimal fouling of the internal ball.

• Can be "locked" in the closed position to comply with toilet waste outlet regulations. US Coast Guard Regulation 33 CFR 159.7 and ISO Standard 8099 for locking of toilet waste outlets.

• Large operating temperature range from -40°C to +110°C.

• Certified to ABYC H27, ISO 9001, AWQC, IMCI ISO 9093-2 and Burea Veritas 27801/A0 standards.

NOTE: TruDesign® Ball Valves should not be used in direct contact with petrol or diesel as the nitrile O-ring may swell affecting their sealing and handle-turning performance.

Load

• Manufactured from high strength, UV stabilised glass reinforced nylon composite making the valve strong and lightweight.

• Can withstand a static load of 227kg for a maximum of 30 seconds.

• No additional bolts or fasteners through or on the hull.

• Can be retrofitted to existing TruDesign® assemblies.

• Compatible with all hull types across a wide range of thicknesses.

• Protects vulnerable areas that can be inadvertently struck by loose items in the hull.

• Easy to install.

• Certified to ABYC H27 standards.

450090 Ball Valve Position Monitor Display Panel

• Supply voltage: 9.5V - 12V DC.

• Max. switching current: 500mA.

• Wire Length: 2m (6.5').

• Monitoring upto 4 valves from an accessible location.

• Indication of multiple Ball Valve positions.

• Can to be used as an engine interlock to disable starting when closed.

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• UV resistant, suitable for all marine environments.

• Large operating temperature range from -40°C to +110°C.

• Certified to ABYC H27, ISO 9001, AWQC, IMCI ISO 9093-2 and Burea Veritas 27801/A0 standards.

NOTE: TruDesign® Ball Valves should not be used in direct contact with petrol or diesel as the nitrile O-ring may swell affecting their sealing and handle-turning performance.

Mounting Bracket For Ball Valves

Part No.

450260

450070 - 450075

Ball Valves - Position Monitor

Ball Valves - Position Monitor Panel

Bearing Collars

Ball Valves - Manual

TruDesign® - Connectors

Ball Valves - Compact

450084 1/2" BSPF 3/4" 19 50

450085 3/4" BSPF 3/4" 19 50

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• UV resistant, suitable for all marine environments.

• Large operating temperature range from -40°C to +110°C.

• Certified to ABYC H27, ISO 9001, AWQC, IMCI ISO 9093-2 and Burea Veritas 27801/A0 standards.

NOTE: TruDesign® Compact Ball Valves should not be used in direct contact with petrol or diesel as the nitrile O-ring may swell affecting their sealing and handle-turning performance.

Ball Valve - Replacement 'T' Handle

• Replacement 'T' handles for manual ball valves.

• Glass reinforced nylon composite.

Hose Tails - Female Straight

Hose Tails - Male Straight

450085

450084

TruDesign® - Connectors

Hose Tails - Female 90°

• 90° elbow hose tail to BSP female thread can be fitted with 2 hose clamps for a secure connection.

Hose Tails - Male 120°

• 120° hose tail to BSP male thread can be fitted with 2 hose clamps for a secure connection.

Coupling - Female / Male 90°

• 90° elbow BSP male thread to

• Versatile connector for tight corners.

• For ball valves in confined locations. NOTE: Do not use with tapered thread valves or fittings.

Hose Joiner - Straight

• Simple straight connectors for joining two hoses of the same size.

Non-Return Valve - Threaded

• Ideal for stopping water back flow from siphoning.

• Stainless spring - No corrosion or risk of internal valve staying open.

• Very low opening pressure with minimal restriction on flow-rate.

• Minimal installation room needed and no other fittings required.

• The White Arrow identifies water flow direction.

• Recommended operating pressure: 0 - 150 psi (Max 230 psi).

• Recommended operating temperature: 65°C (Max 93°C).

• Glass reinforced nylon composite - High strength, stiffness and light weight.

NOTE: TruDesign® Non-Return Valves should not be used in direct contact with petrol or diesel as the nitrile O-ring may swell affecting their sealing performance.

Non-Return Valve

• Ideal for stopping water back flow from siphoning.

• Stainless spring - No corrosion or risk of internal valve staying open.

• Very low opening pressure with minimal restriction on flow-rate.

• Minimal installation room needed and no other fittings required.

• The White Arrow identifies water flow direction.

• Recommended operating pressure: 0 - 150 psi (Max 230 psi).

• Recommended operating temperature: 65°C (Max 93°C).

• Glass reinforced nylon composite - High strength, stiffness and light weight.

NOTE: TruDesign® Non-Return Valves should not be used in direct contact with petrol or diesel as the nitrile O-ring may swell affecting their sealing performance.

TruDesign® - Connectors, Manifolds, Thru-Bulkhead

&

Hose Joiners - Straight Reducer

• Straight reducer hose joiner can be fitted with 2 hose clamps for a secure connection.

Hose Joiner - Y Piece Tails

• Allow drain hoses to merge into one line turbulent free.

• The Y configuration minimises clogging and facilitates flow.

• Ideal for keeping stainless steel bolt heads away

Hose Joiners - 90° Bend

Washers

• 90° Hose connectors facilitate routing around bends, minimising kinking and strain on hoses.

Thru-Bulkhead Fittings

• The threaded tubes provide a simple and tidy solution for passing plumbing through the bulkhead of boats.

T-Joiners - Universal Manifold

• The T-Piece has two 1-1/2" BSP female threads and one 1-1/2" BSP

male thread allowing the T- Piece to be "daisy-chained".

• The versatility of the T-Piece Connector functions not only as a T-Piece but also as an expandable manifold.

• Can connect multiple drains to one Ball Valve or Skin Fitting (Thru-Hull) outlet.

• Direct connection to a 1-1/2" Ball Valve or 1-1/2" (above waterline) Skin Fitting Connection to plumbing pipework or a secondary Ball Valve with use of the Threaded Connector

• A range of angled hose tail fittings are available - straight, 90°, & 120°.

• Mixed sizes of hose tail fittings can be connected to suit 3/4", 1", 1-1/4" & 1-1/2" I.D. hose.

• Can be Daisy-Chained, creating an economic manifold

TruDesign® - Hose Nozzle, Clips, Clamps & Aquavalve Spanners

Power-Spray Nozzle

23770 Power-Spray Nozzle Black

• Adjustable spray pattern - Versatile usage for washdown or filling applications supplier complete with 3/4" BSP garden hose connector.

• Super tough Nylon 6 Body - High strength and light weight.

• 3/4" BSP Thread - Easy connection to other fittings.

• Auto shutoff - Won’t continue to use water if dropped.

NOTE: See hose coil kit with nozzle part no 23742

Hose Reel Nozzle

23780 Hose Reel Nozzle 50

•

• Made from high impact strength polymer.

• Ideal for all marine, industrial & agricultural applications.

• Meets both New Zealand and Australian Fire Hose Reel Standards and frequently seen on marinas.

• Thread size 3/4" BSP

• Hose Nozzle includes 3/4" BSP Thread with 19mm Tail.

Powerjet Hose Nozzle

• Typical flow rate of up to

Litres/min.

• Made from high impact strength polymer.

• Ideal for all marine, industrial & agricultural applications.

• Meets both New Zealand and Australian Fire Hose Reel Standards and frequently seen on marinas.

• Thread size 1" BSP.

• Hose Nozzle includes 1" BSP Thread with 25 mm Tail.

Hose Adapter - Snap-on

BSP

NPT

3/4" BSPM

Snap-on 3/4" NPTM

• 50 mm in length with a 9 mm bore.

• Can also be used as a engine flush for larger outboards.

• 45335 suits 232140 / 232142 mains pressure reducer and 23952 deck wash nozzle.

Hose Clamp 25 mm Nylon 6

Hose Clamp 32 mm Nylon 6

764158 Hose Clamp 38 mm Nylon 6 Black

• These Hose Clamps are field tests have proven to be ideal when used with our nozzle range.

• The strong, reinforced Nylon 6 moulding acts as a protector and support to the nozzle and eliminates the sharp hose clip problem experienced with standard hose clip systems.

• 316G stainless steel fastenings included guarantee long life and clamp the hose well onto the nozzle fittings.

Saddle Clips & Saddle Base

• Multi-purpose Base (35940) - Can be used on its own to tie down cables & wires or have a Saddle Clip attached for supporting hoses.

• Dual mounting options for Base - Adhesive or screws (or both) - Ability to replace Saddle Clip with another size without disturbing Base.

• Dovetail grooves on the base enhance adhesive performance.

• Durable, flexible Saddle Clip arm - Accepts hoses of varying sizes.

• Base made of UV-stabilized glass-reinforced Nylon 6 (PA6). Saddle clips made of UV-stabilized Acetal copolymer (POM).

• High strength, tough and light weight. Can be used in direct sunlight. Saddle Clip arms are strong yet flexible and won’t ‘creep’ under load.

764150

764152

764154 764156

764158 Hose Clamps

Aquavalve - Diverting Valve - TruDesign®

45348 45350 Aquavalve 3 Way Diverting Valve - No tails 1-1/2" BSPF

45351 Seal Service Kit Includes Silicon Lube suits 45348 & 45350

45346 Replacement Facia suits 45348 & 45350

45347 Bulkhead Thru Extension suits 45348 & 45350

• The TruDesign® Aquavalve has been designed to handle hot or cold water and waste treatment chemicals.

• The Valve is produced in FDA approved materials to handle drinking water but is also ideal as a diverting valve for waste water on sewerage holding or treatment systems.

• Pressure-tested to 300 PSI, with full service and parts support.

• Stainless steel fasteners.

• Handle position lockable.

• Glass reinforced nylon composite - strong, stiff, and lightweight.

• Immune to corrosion and electrolysis for long service life.

• Chemical resistant - Impervious to diesel, petrol and antifouling paints.

• UV resistant, suitable for all marine environments.

• Certified to ABYC H27 and Burea Veritas 27801/A0 standards.

NOTE: See Aquavalves Accessories for Tail and Threaded options. Caution: Not to be used for diverting fuels.

TruDesign® - Aquavalves

Aquavalve - Electronic - TruDesign®

45299 Aquavalve Electric Valve with Control Panel 12/24

• The Electronic Aquavalve allows the diverting valve to be operated with the push of a button on the control panel. The indicators on the control panel show the current position of the valve. The valve has two positions 'holding tank' or 'overboard'.

• Clear indication on control panel as to current valve position.

• Versatility of installation with a vast range of hose and bend adaptors.

• Compatible with Manual Aquavalve adaptors.

• Stainless steel fastenings.

• Each valve seal tested to check no O-ring leakage.

• The valve has been tested to 300 PSI.

• Glass reinforced nylon composite - strong, stiff, and lightweight.

• Immune to corrosion and electrolysis for long service life.

• Chemical resistant - Impervious to diesel, petrol and antifouling paints.

• UV resistant, suitable for all marine environments.

• Certified to ABYC H27, Burea Veritas 27801/A0 and CE standards.

NOTE: See Aquavalves Accessories for Tail and Threaded options.

Caution: Not to be used for diverting fuels.

Aquavalve - Bulkhead

• Stainless steel fasteners - Will not corrode in salt laden air.

• Easy installation - With a range of straight, 90° and 120° tails, and two seal options, plumbing in confined spaces is made easy.

• Handle position lockable.

• All valves are pressure tested to ensure quality and safety in respect to sealing and operation.

• The Aquavalve® is the only valve on the market today with smooth movement and an excellent seal with good wear resistance.

• Avoids using pipe wrenches that gouge the fitting.

• Facilitates access in tight places.

• Fascia plate on standard model can be removed to reveal simple "open - open - inlet" labelling - Where product is not used for marine toilets, all toilet references are removed.

• Glass reinforced nylon composite - strong, stiff, and lightweight.

• Large operating temperature range from -40°C to +110°C.

• Certified to ABYC H27 and Burea Veritas 27801/A0 standards.

NOTE: See Aquavalves Accessories for Tail and Threaded options.

Caution: Not to be used for diverting fuels.

TruDesign® Aquavalves Accessories

Connector 3 Ways

• An assortment of tails can be fitted to the 3 Way Connector making it extremely versatile.

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• UV resistant, suitable for all marine environments.

Caution: Not to be used for diverting fuels.

Aquavalve Hose Tails - Angled

• Angled Tails suited to the most common sizes of tubing used in marine plumbing.

• Tails come packaged with a Blue Seal to allow fitting to be rotated to a more suitable position if required.

NOTE: Includes Blue Seal.

- Vented

• Threaded Vent Plug ideal for holding tank.

Aquavalve Hose Tails - Straight

• Straight Tails suited to standard sizes of tubing.

Aquavalve - Threaded Nipple

• Used to connect the Aquavalve or 3 Way Connector to rigid PVC plumbing.

• Interfaces with a PVC fitting designed for connection to steel piping.

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• Chemical resistant - Impervious to diesel, petrol and antifouling paints.

• UV resistant, suitable for all marine environments.

Plug

• The plug can be used to block one port when

or maintenance is

Spanners

• Spanner to tighten TruDesign® Aquavalve hose tails to a maximum of 16Nm (12ft/lbs)

Vented Loops - Electric Solenoids

45323 Vented Loop with Solenoid Valve 12 25 1"

453230 Vented Loop with Solenoid Valve 24 25 1"

45327 12V Solenoid Valve Only suits Vented Loops

453271 24V Solenoid Valve Only suits Vented Loops

• Robust polymer covered solenoid for long life in the marine environment.

• Diaphragm valve provides faster breaking of siphon due to larger flow rate available.

• Female threaded Solenoid Valve - No brass/bronze adapter to corrode.

• 3 screw mounting points give secure and easy installation.

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• Chemical resistant - Impervious to diesel, petrol and antifouling paints.

• UV resistant, suitable for all marine environments.

Scoop / Strainers - Oval

• Compatible with all hull types - Can be used on aluminum, steel, wood or FRP hulls.

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• Chemical resistant - Impervious to diesel, petrol and antifouling paints.

• UV resistant, suitable for all marine environments.

Vented Loops

45324 Nylon Vented Loop

453248 45325 Nylon Vented Loop

453249 45326 Nylon Vented Loop

453281 45328 Replacement Cap and Valve

• Glass reinforced nylon composite for high strength and light weight.

• Silicone duck bill valve - Long life with no perishing or hardening.

• 3 screw mounting points give secure and easy installation.

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• Chemical resistant - Impervious to diesel, petrol and antifouling paints.

• UV resistant, suitable for all marine environments.

45324 - 45326

Scoop / Strainers - Round

• Ideal for small gen-sets and water makers.

• Ideally suited to fit 1-1/4" skin fittings or smaller.

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• Chemical resistant - Impervious to diesel, petrol and antifouling paints.

• UV resistant, suitable for all marine environments.

45327/ 453271

45323/ 453230

Scoop fits neatly over the skin fitting (sold separate).

TruDesign® - Tank Fittings

Strainers - Hose Inlet

450210 Strainer Hose Inlet 1-1/4" 32 Black 450211 Strainer Hose Inlet 1-1/2" 38 Black

450212 Strainer Hose Inlet 2" 50 Black

450213 Strainer Hose Inlet 3" 75 Black

• These strainers have been designed to attach to the suction end of a hose when sucking water from a stream, lake, water race etc.

• The grille stops small particles from blocking the pump system.

• Designed so there is no restriction in water flow.

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• Chemical resistant - Impervious to diesel, petrol and antifouling paints.

• UV resistant, suitable for all marine environments.

• Used as an overflow check valve or tank pickup.

• Angled end can be cut to suit to suit different sized holding tanks.

• Flanged end is retained in tank fitting without use of adhesive.

Caution: DO NOT Cut Flange End.

end is

Fittings

• Specifically designed to suit Tank Fitting Tubes (450228 and 450229)

• Glass reinforced nylon composite - High strength, stiffness and light weight.

• Immune to corrosion and electrolysis for long service life.

• Chemical resistant - Impervious to diesel, petrol and antifouling paints.

• UV resistant, suitable for all marine environments.

29600F Alloy Weld-in Flange Only Suits Tank Fittings - 1-1/2" BSPF

• Chrome plated brass ideal for all fuel line installations.

• Corrosion resistant handle.

• Parallel thread.

• Three Way L-Port Chrome Plated Brass Ball Valves.

• Provides two different flow directions, ideal for controlling two fuel tanks.

• Nickel plated handle.

• Parallel Thread.

• Three Way T-Port Chrome Plated Brass Ball Valve.

• Provides two different flow directions, ideal for controlling two fuel tanks.

• Nickel plated handle.

• Parallel Thread.

Ball Valves - BSP - 3 Piece - Stainless Steel

• Stainless steel 3 Piece Ball Valve.

• PTFE gaskets, washers and ball seat.

• Locking handle.

• Parallel thread.

• Max working temp: -20°C~+160°C.

• Fluid Transfer: Water, Oil, Gas and Acid.

• 316G stainless steel ball, stem and handle.

• Full bore parallel BSP (Female) threaded ports.

• Three Way L-Port 316G Stainless Steel Ball

• Provides two different flow directions, ideal for controlling two fuel tanks.

Parallel Thread.

Ball Valves - BSP - Stainless Steel

Ball Valves - BSP - Chrome Plated Brass

Valves.

•

Ball Valves - 'L' Port BSP - Stainless Steel

Ball Valves - 'L' Port BSP - Chrome Plated Brass

45136 / 45137 45138 - 45140

Ball Valves - 'T' Port BSP - Chrome Plated Brass

Ball Valves, Gate, Y Valves & Connectors

Ball Valves - BSP - Bronze

• Non-corrosive Bronze Ball Valve with a stainless steel nut and handle.

• Full bore parallel (Female) threaded ports.

Gate Valves - BSP - Bronze

•

•

•

•

Thread Seal Tape - Plumber's Tape

• PTFE

• Ideal for sealing pipe threads.

Tails x 3/4" BSP Female

• UV stabilised materials for long life. Hose

• Connect to tap adaptors, tap timers, manifold and multi outlet distributors and is used with low pressure poly pipe.

• Simple to use ergonomic design.

Hose Tails x 3/4" BSP Male

• Tapered entry on all barbed fittings for ease of installation.

• Range includes common Australian and International tube sizes.

• UV stabilised materials for long life.

Ball Valve - PVC - Small

- BSP Connectors - Stainless Steal

1" • Compact style noncorrosive PVC ball valve with large handle.

• ON/OFF Tap.

• 2 x Barbed tails.

Hose Tails x BSP Female - S/S

Connectors - Stainless Steal, Brass and Bronze

• 90° Elbow BSP Male to hose tail.

• Bronze.

Hose Tails

• BSP (Male or Female) to snap-on garden hose tail.

Brass.

Hose Tails - BSP Male - Polypropylene

• UV and chemical resistance.

• Long tail and thick walls.

• Polypropylene (PP).

•

•

Hose Straight Joiner - Polypropylene

•

•

thick walls.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C.

• Pressure: 120 PSI.

Hose Tails - 90° Elbow BSP Male - Polypropylene

• UV and chemical resistance.

• Long tail and thick walls.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C.

• Pressure: 120 PSI.

• UV and chemical resistance.

• Long tail and thick walls.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C

• Pressure: 120 PSI. .

Hose Tail - T-Joiner - BSP Male - Polypropylene

• UV and chemical resistance.

• Long tail and thick walls.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C.

• Pressure: 120 PSI.

Hose T Joiner - Polypropylene

• UV and chemical resistance.

• Long tail and thick walls.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C.

• Pressure: 120 PSI.

Hose Tails - BSP Male - Reducer - Polypropylene

•

•

•

(PP).

• Operating Temp: 0°C to 120°C.

• Pressure: 120 PSI.

Hose Tails - BSP Female - Reducer - Polypropylene

• UV and chemical resistance.

• Long tail and thick walls.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C •

Hose Joiner - 90° Elbow - Polypropylene

- Polypropylene

•

• Long tail and thick walls.

•

•

•

Coupling - BSP Male/Female - Polypropylene

• UV and chemical resistance.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C.

• Pressure: 120 PSI.

Nipples - BSP Male - Polypropylene

•

•

•

•

Hose Joiners - Reducer - Polypropylene

• UV and chemical resistance.

• Long tail and thick walls.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C.

• Pressure: 120 PSI.

Coupling - BSP Female - Polypropylene

•

•

•

•

Coupling - 90° Elbow - BSP Female - Polypropylene Coupling - T Joiners - BSP Female -

• UV and chemical resistance.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C.

• Pressure: 120 PSI.

• UV and chemical resistance.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C.

• Pressure: 120 PSI.

• UV and chemical resistance.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C.

• Pressure: 120 PSI.

Bushes,

End Caps, Tube Holders

Bushes - BSP Male / Female - Polypropylene

• UV and chemical resistance.

• Polypropylene (PP).

• Operating Temp: 0°C to 120°C.

• Pressure: 120 PSI.

End Caps - BSP Male - Polypropylene

•

•

•

•

(PP).

End Caps - BSP Female - Polypropylene

•

•

•

• Pressure: 120 PSI.

Tube Clip - HD - Polyethylene

•

• Heavy duty clips and supports.

• Polyethylene (PE).

• Operating Temp: -80°C to 70°C.

•

Hose Clamps - Micro - Perforated - S/S

• For marine, industrial, automotive, agricultural, chemical and general purpose use.

• Band: 301 Stainless steel.

• Housing: 301 Stainless steel.

• Screw: 305 Stainless steel (Hex head).

• Australian made quality.

Hose Clamps - Perforated - S/S

• For marine, industrial, automotive, agricultural, chemical and general purpose use.

• Band: 301 Stainless steel.

• Housing: 301 Stainless steel.

• Screw: 305 Stainless steel (Hex head).

• Australian made quality.

Hose Clamps - Micro - Solid - S/S

• For marine, industrial, hardware auto and general purpose use.

• Rolled edge and smooth underside to prevent hose damage.

• Band: 304 Stainless steel.

• Housing: 304 Stainless steel.

• Screw: 302 Stainless steel.

• Removable safety collar.

• Australian made quality.

Hose Clamps - Solid - S/S

• Rolled edge and smooth underside to prevent hose damage.

• Band: 304 Stainless steel.

• Housing: 304 Stainless steel.

• Screw: 302 Stainless steel.

• Removable safety collar.

• Australian made quality.

Hose Clamps

Hose Clamps - T-Bolt - Stainless Steel

• For heavy duty applications where large tightening forces are required.

• Rolled edge to prevent hose damage.

• Solid trunnions with hex head bolt.

• Band: 304 Stainless.

• Bridge: 304 Stainless Steel.

• Bolt: High tensile 316G Stainless steel.

• Trunnion: 300 Series stainless.

• Collar: 300 Series stainless.

RCM Water Heater - Dual Heating - Stainless Steel

• Dual heating - Incoloy Electric Element and Heat Exchanger Coil.

• Incoloy* Electrical Heating Element is 1250 Watts allowing hot water production when engine heat is not available.

• Heat Exchanger Coil features a large surface area designed to generate a large output of hot water.

• Insulation uses closed cell expanded polyurethane foam (HFC, CFC, HCFC and HFA free).

• Water Heater Tank has both Pickling and Passivation treatment for increased anti-corrosion performance.**

• Adjustable safety thermostat.

• Pressure relief and non-return valve.

• Easy drain connection.

• Power cable and Australian plug supplied (AS/NZS 3112).

• Purpose built from high-quality materials for the marine environment: Tank: AISI 316L Stainless Steel.

Heat Exchanger: AISI 316L Stainless Steel.

External Casing: AISI 304 Stainless Steel.

Mounting Brackets: AISI 304 Stainless Steel.

• RCM Certified: SAA-180560-EA.

• CE Certified EN 60335.

NOTE:

* Incoloy refers to a range of superalloys designed for excellent corrosion resistance as well as strength at high temperatures.

** Both Pickling and Passivation are chemical treatments applied to the surface of stainless steel to remove contaminants and assist the formation of a continuous chromium-oxide, passive film which protect the Stainless steel from corrosion. Heating Time in Minutes

44304

44305

44307

44308

44306

Water Heaters - Stainless Steel

Water Heater - Rectangular - Stainless Steel

• Dual heating - Incoloy Electric Element and Heat Exchanger Coil.

• Incoloy* Electrical Heating Element is available in 850 Watts allowing hot water production when engine heat is not available.

• Heat Exchanger Coil features a large surface area designed to generate a large output of hot water.

• Insulation uses closed cell expanded polyurethane foam (HFC, CFC, HCFC and HFA free).

• Water Heater Tank has both Pickling and Passivation treatment for increased anti-corrosion performance.**

• Adjustable safety thermostat.

• Pressure relief and non-return valve.

• Easy drain connection.

• Power cable supplied.

• Purpose built from high-quality materials for the marine environment: Tank: AISI 316L Stainless Steel.

Heat Exchanger: AISI 316L Stainless Steel.

External Casing: AISI 304 Stainless Steel.

Mounting Brackets: AISI 304 Stainless Steel.

• RCM Certified: SAA-180560-EA.

• CE Certified EN 60335.

NOTE:

* Incoloy refers to a range of superalloys designed for excellent corrosion resistance as well as strength at high temperatures.

** Both Pickling and Passivation are chemical treatments applied to the surface of stainless steel to remove contaminants and assist the formation of a continuous chromium-oxide, passive film which protect the Stainless steel from corrosion.

Water Heater - Rectangular Water Heater - Replacement Parts

Thermostat suits 20A

Electrical heater element:

• Heats water when the boat engine is off.

Water Heater Anode:

• Replacement Magnesium Anode.

Thermostat:

• Cuts off the electrical supply to the heater element as the preset temperature is achieved (temperature can be set between 0°C and 70°C).

*NOTE: For more information on 44300 contact one of our technical staff.

• Dual heating - Incoloy Electric Element and Heat Exchanger Coil.

• Incoloy* Electrical Heating Element is available in 850 and 1250 Watts allowing hot water production when engine heat is not available.

• Heat Exchanger Coil features a large surface area designed to generate a large output of hot water.

• Insulation uses closed cell expanded polyurethane foam (HFC, CFC, HCFC and HFA free).

• Enamelled steel tank is internally coated according to DIN 4753.**

• Replaceable Magnesium anode is fitted to all Enamelled Steel units to protect against galvanic corrosion.

• External casing is made of pre-painted aluminium, chosen because of its suitability for marine applications

• Adjustable safety thermostat.

• Pressure relief and non-return valve.

• Power cable supplied.

• Purpose built from high-quality materials for the marine environment: Enamelled Steel Tank: internally coated according to DIN 4753.

External Casing: Pre-Painted Aluminium. Mounting Brackets: AISI 304 Stainless Steel.

• CE Certified EN 60335.

NOTE:

* Incoloy refers to a range of superalloys designed for excellent corrosion resistance as well as strength at high temperatures.

** DIN 4753 refers to the standard for Water heaters and water heating insulations for drinking and service water.

44230

44232

44234

44238

44236