RUST-OLEUM® 1-2-3 Maintenance catalogue

1-2-3

MAINTENANCE INDUSTRIAL PAINTS AND RELATED PRODUCTS FOR QUICK & EASY DAILY MAINTENANCE

METAL PROTECTION

FLOOR COATINGS

INSTANT ROOF REPAIR

KNOW-HOW TO PROTECT™ WWW.RUST-OLEUM.EU

REPAIR, LUBRICATION AND CLEANING

Rust-Oleum® products save time and money Every RUST-OLEUM® product is designed to make your job easier and therefore meets at least one of the following requirements: 1. Less time spent on preparation 2. Less time spent on application 3. Less interruption of work 4. Longer lasting

RUST-OLEUM® Know-How to protect since 1921 In 1921 Captain Robert Fergusson perfected a paint based on fish oil that prevented rust and was capable of drying overnight without leaving any unpleasant odours.

RUST-OLEUM® Corporation was born.

INDEX

Introduction

PAGE

2

Industrial paint aerosols: HARD HAT®

2

Surface Preparation

9

Galvanising

13

Topcoats

19

Marking

31

Metal Protection: CombiColor®

38

Floor coatings

50

Waterproofing

64

Technical Sprays: X1

68

Anti-Graffiti: Graffiti-Shield™

76

RUST-OLEUM® 1-2-3 MAINTENANCE FOR ALL TRADESPEOPLE FIND YOUR PRODUCT WWW.RUST-OLEUM.EU

WWW.RUST-OLEUM.EU

3

FROM SUBSTRATE

TO SOLUTION

Temporary rust protection

BARE STEEL

RUSTED METAL

Daily touch-up maintenance (Aerosols)

Regular maintenance (Brush/roller applied)

• HARD HAT® Rust Primer 2169/2182 • HARD HAT® Advanced • 6400 Shopprimer

• HARD HAT® Rust Primer 2169/2182 • HARD HAT® Topcoat • HARD HAT® Advanced

• CombiColor® Original

• HARD HAT® Rust Primer 2169/2182 • 6400 shopprimer

• HARD HAT® Rust Primer 2169/2182 • HARD HAT® Topcoat • HARD HAT® Advanced

• CombiColor® Original, Aqua or Non-Zinc

• HARD HAT® Topcoat • HARD HAT® Advanced

• CombiColor® Original, Multi-Surface, Aqua or Non-Zinc

• 2925 Paint Stripper • HARD HAT® Rust Primer 2169/2182 • HARD HAT® Topcoat • HARD HAT® Advanced

• 2925 Paint Stripper • CombiColor® Original, Aqua or Non-Zinc

• Old galvanised: HARD HAT® 2185 • New galvanised: HARD HAT® 2117 or HARD HAT® 2120

• CombiPrimer® 3302 + CombiColor® Original or Non-Zinc • CombiPrimer Aqua (3369AQ/3380AQ) + CombiColor Aqua

• HARD HAT® Adhesion primer 2102 • HARD HAT® Topcoat • HARD HAT® Advanced

• CombiPrimer® 3302 + CombiColor® Multi-Surface

• HARD HAT® Advanced

• CombiColor® Multi-Surface

• 2925 Paint Stripper • HARD HAT® Advanced

• 2925 Paint Stripper • CombiColor® Multi-Surface

• HARD HAT® Advanced

• CombiColor® Multi-Surface

• Adhesion primer 2102 • HARD HAT® Topcoat • HARD HAT® Advanced

• CombiColor® Multi-Surface

• HARD HAT® Topcoat • HARD HAT® Advanced

• CombiColor® Multi-Surface • 7100/7200 floor coating • EpoxyShield® SEALER and ULTRA

PAINTED METAL (GOOD CONDITION)

PAINTED METAL (POOR CONDITION)

• HARD HAT® Advanced

GALVANISED STEEL

®

• HARD HAT 2180/2185

ALUMINIUM

BARE WOOD

PAINTED WOOD (POOR CONDITION)

PAINTED WOOD (GOOD CONDITION)

PLASTIC / HARD PVC CONCRETE (>2 years old)

Clean & Degrease

4

Manually derust

Remove loose paint

Roughen surface

SURFACE PREPARATION Extra protection (Brush/roller applied)

GENERAL CLEANING/DEGREASING Remove any grease, oil and any other contamination using a special cleaner or ammonia.

For large areas high pressure steam cleaning is the ideal solution.

Make sure that the surface is completely dry and free of residue before coating.

• CombiPrimer® 3369/3380 + CombiColor® Original

PAINTED SURFACES Remove any loose paint by using a scraper. Check the adhesion of any fixed paint.

If the paint is in good condition, clean/degrease, sand the surface, make it dust-free and make sure it’s dry before painting. Follow the surface preparation steps for the substrates below.

• CombiPrimer® 3369/3380 + CombiColor® Original

BARE METAL Remove all surface contamination using a special cleaner or • CombiColor® Original, Multi-Surface, Aqua or Non-Zinc

• 2925 Paint Stripper • CombiPrimer® 3369/3380 + CombiColor® Original or Non-Zinc • CombiPrimer Aqua (3369AQ/3380AQ) + CombiColor Aqua

• CombiPrimer® 3302 + CombiColor® Original or Non-Zinc • CombiPrimer Aqua (3369AQ/3380AQ) + CombiColor Aqua

• CombiPrimer® 3302 + CombiColor® Original or Non-Zinc • CombiPrimer Aqua (3369AQ/3380AQ) + CombiColor Aqua

• 2 coats of CombiColor® Original, Aqua or Non-Zinc. First coat 10% diluted

• 2925 Paint Stripper & 2 coats of CombiColor® Original, Aqua or Non-Zinc.

First coat 10% diluted.

• 2 coats CombiColor® Original, Aqua or Non-Zinc

• CombiPrimer® 3302 + CombiColor® Original or Non-Zinc

• EpoxyShield® MAXX

RUST-OLEUM® 2901. Rinse the surface thoroughly and let dry before applying the first paint layer. Although HARD HAT® and CombiColor® topcoats can be applied to bare metal, the use of a metal primer or HARD HAT® Advanced is always recommended for longer lasting results.

RUSTED METAL Remove any loose rust by using a scraper. Remove fixed rust using a wire brush. Derust until the rusted substrate is smooth and equal. Clean/ degrease the surface using a special cleaner or RUST-OLEUM® 2901. Make sure that the surface is complety dry before applying the first paint coat.

GALVANISED STEEL Remove any zinc oxide (white rust) from the surface using water and a Scotch-Brite to obtain a smooth surface. RUST-OLEUM® SurfaEtch solution 108 can be used to neutralise any alkaline residue. It produces a finely etched surface enhancing the adhesion of the coating. Then apply RUST-OLEUM® adhesion primers HARD HAT® 2102 or CombiColor® 3302 before topcoating. Note that it is not recommended to apply HARD HAT® and CombiColor® topcoats directly to galvanised steel, except HARD HAT® Advanced.

ALUMINIUM Use a Scotch-Brite® and water to remove any aluminium oxide and to roughen the surface for a better paint adhesion. Then apply RUST-OLEUM® adhesion primers HARD HAT® 2102 or CombiColor® 3302 before topcoating. Note that it is not recommended to apply HARD HAT® and CombiColor® topcoats directly to aluminium, except HARD HAT® Advanced.

BARE WOOD Make sure the wood is completely dry. Clean the surface and sand it to ensure good paint adhesion. Make the surface dust free to ensure that all sand dust is removed before applying the first paint layer.

PLASTICS Only hard plastic surfaces can be painted (such as PVC). First clean/ degrease the substrate using a special cleaner, then rough it up using a Scotch Brite® or sandpaper. Clean/Degrease the surface again and apply RUST-OLEUM® adhesion primers HARD HAT® 2102 or CombiColor® 3302 before topcoating or direcly CombiColor® Multi-Surface.

CONCRETE New concrete has to be left unpainted for the first 30 days. Make sure that the concrete is dry by taping a plastic sheet (1 x 1m) on the substrate for 24 hours. Check the underside of the sheet for any moisture, discoloration or condensation on the concrete. If so, do not paint the substrate. Clean the surface with RUST-OLEUM® 2901 premixed floor cleaner. Smooth and dense concrete should first be etched using RUST-OLEUM® Surfa-Etch 108. Note that CombiColor® and 7200 Floor coating can only be applied to concrete that is older than 2 years.

WWW.RUST-OLEUM.EU

5

MORE THAN EVER THE NO. 1 INDUSTRIAL PAINT AEROSOL HARD HAT ® solves any maintenance touch-up and marking challenge, no matter what surface, condition, equipment or infrastructure.

The recent product innovations confirm and enhance HARD HAT ®’s No. 1 position in industrial paint aerosols.

COVER IT ALL TACKLE YOUR SURFACE PREPARATION, GALVANISING OR TOPCOAT CHALLENGES WITH OUR SELECTION OF COLOURS AND FINISHES.

WORK MORE EASILY

SPRAY MORE

ENJOY OUR EASY GRIP HANDLE AND GET THE JOB DONE IN ONE GO, THANKS TO OUR HIGH-OPACITY SPRAYS.

OUR AEROSOLS HAVE THE HIGHEST PAINT PERCENTAGE ON THE MARKET, SO YOU SPRAY MORE PAINT PER CAN AND CUT COSTS.

ENJOY THE RESULT EXPECT COLOURS AND GLOSSY FINISHES THAT LAST A LONG TIME WITHOUT CHIPPING, CRACKING OR PEELING.

CONTINUALLY IMPROVING You know our HARD HAT aerosols to be a top brand of spray paints for any maintenance job.

HARD HAT® comes in many versions and colours, so you can use the right aerosol for any kind of challenge. Still, choosing the most compatible product isn’t always easy, so we made some interesting improvements to benefit our customers. ®

6

A RESHUFFLED PRODUCT PORTFOLIO FOR A CRYSTAL-CLEAR VIEW ON WHAT PRODUCT TO USE We analysed the many existing products and renamed some of them, to make it easier for customers to navigate the portfolio.

HARD HAT ® SURFACE PREPARATION EASY PRE-TREATMENT THAT PAYS OFF When surfaces are stained, slightly rusting, lack adhesion or need stripping, you need to prepare them before applying a new layer. HARD HAT ® Surface Preparation aerosols solve many issues, saving you time and money.

HARD HAT ® GALVANISING FIGHT STEEL CORROSION WITH CATHODIC PROTECTION Cathodic treatment of steel constructions and machinery is only effective when using high-quality components that give durable protection. All HARD HAT ® Galvanising coatings guarantee the best performance on the market.

HARD HAT ® TOPCOATS TOUCH-UPS IN SECONDS, TOPCOATS FOR YEARS Many surfaces need incidental or periodic repairs or touch-ups, to freshen up colours, protect metal base layers, repair glossy finishes… HARD HAT ® Topcoats offers various industrial aerosols solving these issues in seconds and last longer.

HARD HAT ® MARKING MARK ANY SURFACE, IN ANY COLOUR Need to mark a spot, demarcate traffic areas or apply symbols or messages on rough surfaces? Use HARD HAT ® Marking aerosols for writing, spraying and line marking paints in eye-catching shades. Perfect for last-minute signage on site.

WWW.RUST-OLEUM.EU

7

A HANDY PRODUCT SELECTOR TO FACILITATE THE SELECTION PROCESS To guide our customers to the right solution, we developed a handy productselector. Customers can use it to find the best solution for their challenge in no time, for any indoor or outdoor application or substrate.

DON’T YOU HAVE A SPECIFIC APPLICATION IN MIND?

PRACTICAL GUIDANCE FOR: • Specific substrates steel, wood, plastic, etc.

• Particular conditions heat, cold, chemical wear, UV resistance, heavy wear, etc.

• Type of maintenance indoor and outdoor

LOOK INTO A PRODUCT’S SPECIFIC FEATURES ON THE DIFFERENT PRODUCT PAGES.

THEY ALSO GIVE INFORMATION ON COMBINABLE AND ALTERNATIVE PRODUCTS, AND DIRECT YOU TO THE PREFERRED DISTRIBUTOR IMMEDIATELY.

8

PROPER SURFACE PREPARATION FOR ANY SUBSTRATE HARD HAT® Surface Preparation aerosols make high quality surface pretreatment a walk in the park. Thorough priming, covering or stripping has never been easier.

ANTI-RUST PRIMER

ADHESION PRIMER

STAIN BLOCKER

PAINT STRIPPER

HARD HAT ® SURFACE PREPARATION EASY PRE-TREATMENT THAT PAYS OFF

WWW.RUST-OLEUM.EU

9

STAIN BLOCKER

MAKE IT WHITE AGAIN

HARD HAT® STAIN BLOCKER

The effective solution to stains on ceilings, walls, wood, etc

STAIN BLOCKING

• Matt white finish, best possible opacity (Non-yellowing) • Touch dry (in 5-10 minutes), Tack-free time: 10 min • Overcoat time: 30 min • For application on concrete, plaster, particle board existing coatings, wall paper etc.

• Odourless. Recoatable with standard wall paints Masks stains from: Nicotine, Soot, Moisture, Grease and Tar

10

2990 - 500 ml Matt white

QUICK PRIMERS

A PERFECT BASIS HARD HAT® ANTI-RUST PRIMER

The quick anti-rust protection • Ready to recoat after just 10 minutes, to handle after 30 min.

• For new or slightly rusty surfaces • Penetrates deeply into the surface and does not give rust a chance • Grey for light coloured topcoats and red for dark coloured topcoats

1

2

Rusted steel

2169 500 ml

Manually derusting and degreasing

3

Apply primer

For brushable metal primers see Combi-Primer® and Shopprimers

2182 500 ml

Matt grey

Tack-free time: 30 min Overcoat time: 10 min

Red brown

HARD HAT® ADHESION PRIMER

Undercoat for difficult subtrates • Ready to recoat after just 30 minutes • Unique coverage: 5.5 m2 per aerosol • To recoat with HARD HAT® topcoats • Wide angle spray pattern for a large and even coverage

GREAT COVERAGE Can be used on: Galvanised, stainless steel, aluminium, copper, hard pvc, glass and ceramics

2102 500 ml

Clear

WWW.RUST-OLEUM.EU

11

NR.1 PAINT STRIPPER

NR.1 PAINT STRIPPER

Methylene Chloride Free!

• • • • •

Far more effective than other paint strippers on the market Gel like paste Works at low temperatures (< 0 °C) Also effective as glue remover Quick acting

1

2

Apply product

3

Allow to work

2-4 m²/l

12

Scrape off old paint

25.0.75 - 25.2.5 0.75 ml - 2.5 L

2925 500 ml

POWERFUL PROTECTIVE ZINC-BASED AEROSOLS Zinc-based steel protection only works effectively with a high zinc content spray applied evenly at a constant high yield. Look for HARD HAT® Galvanising coatings, the top performer on the market.

GALVA ZINC

GALVA EXPRESSE

GALVA ZINC-ALU

GALVA PLUS

HARD HAT ® GALVANISING FIGHT STEEL CORROSION WITH CATHODIC PROTECTION

WWW.RUST-OLEUM.EU

13

HARD HAT® ZINCS

WHY BETTER? RUST-OLEUM® PRODUCES ZINC RICH PAINT ITSELF That is how RUST-OLEUM® manages to keep the quality of its’ zinc rich paints so constant and at a high level. Many others buy it from various sources at varying qualities.

BETTER PERFORMANCE SPECIAL NOZZLE

• More paint per aerosol, more square metres • Constant and high yield for direct results • Usable down to 0º C • Safer to use thanks to limited overspray

All RUST-OLEUM® zinc sprays feature a special nozzle to limit overspray.

90 HOURS SALT SPRAY TEST! (DIN 50021 SS)

Galva zinc

Competitor

HARD HAT® GALVA ZINC

The nr.1 zinc coating • • • • •

90% ZINC

Cathodic protection of bare and galvanised steel 90% pure zinc in dry paint film Resists 500 hours of salt spray testing (DIN 50021 SS) To recoat within one hour, brush version after 4 hours To recoat with HARD HAT® metallic sprays

COLD GALVANISING 1085.1 1kg

Matt grey

14

Standard colours in tabel on page XX

2185 500 ml

HARD HAT® ZINCS

PRODUCT OVERVIEW Technical information

GALVA ZINC

Appearance

Matt grey

Zinc %

2185 / 1085.1

2180

GALVA EXPRESSE

2117 / 1017.1

2120

GALVA ZINC-ALU

GALVA PLUS

Matt grey

Sparkling aluminium

Aluminium gloss

90%

68%

80%

54%

Aluminium %

0%

1%

10%

23%

Salt spray test

500 hrs.

400 hrs.

340 hrs.

310 hrs.

Tack free

10 min / 15 min

5 min

20 min / 30 min

15 min

To handle

30 min / 2 hrs.

10 min

60 min / 3 hrs.

60 min

Heat-resistant

450°C / 300°C

350°C

450°C / 300°C

150°C

Main advantage

Best protection

Quick drying

Good protection + finish

Finish like new galvanised

5

min

HARD HAT® GALVA EXPRESSE

The super-fast zinc primer • Protection and quick drying in one • Tack free after just 5 minutes, to handle after 10 minutes • Ideal for production and construction environments • Resists 400 hours of salt spray testing (DIN 50021 SS)

COLD GALVANISING 2180 500 ml

Matt grey

WWW.RUST-OLEUM.EU

15

HARD HAT® ZINCS

GLOSS GALVANISING

GALVA ZINC-ALU

Protection and finish in one

GLOSS GALVANISING

• Zinc coating with sparkling aluminium particles • Resists 340 hours of salt spray testing (DIN 50021 SS) • The best compromise between a zinc spray and an aluminium spray

1017.1 1kg

2117 500 ml

Sparkling aluminium

GALVA PLUS

Zinc gloss renewal • Appearance similar to new galvanised • For touching-up new galvanised • Resists 310 hours of salt spray testing (DIN 50021 SS) • Lower zinc contents, more aluminium

GLOSS GALVANISING 2120 500 ml

Aluminium gloss

16

THE TRUTH ABOUT

LOW COST ZINC SPRAYS BEST ZINC SPRAYS

CONTAINS

87-90%

100% PURE ZINC...

DOES NOT MEAN ANYTHING

ZINC

Only zinc that is 100% pure brings cathodic protection.

But more important is the amount of pure zinc in the dry paint film. Cheaper zinc sprays often only contain up to 60% zinc. The best zinc sprays contain the maximum amount of 87-90% zinc in the dry paint layer.

WEIGHT OF THE CAN SAYS NOTHING Many suppliers of cheap zinc aerosols use filling materials to make the can appear to be heavier.

BRAND X

solvents

GROSS CONTENTS SAYS NOTHING An aerosol is made up of paint, solvents and propellent. The relation between these varies much from supplier to supplier. This results into the fact that one 500 ml can contains more paint than the other, affecting the coverage per aerosol.

propellent paint

BRAND X

RUST-OLEUM SPRAY

WWW.RUST-OLEUM.EU

17

A HANDY HARD HAT ® PRODUCT SELECTOR TO FACILITATE THE SELECTION PROCESS To guide our customers to the right solution, we developed a handy productselector. Customers can use it to find the best solution for their challenge in no time, for any indoor or outdoor application or substrate.

ASK AN EXPERT

Welcome to the

PRODUCT SELECTOR

HARD HAT® COVERS IT ALL

FIND YOUR SOLUTION

FIND YOUR IDEAL SOLUTION

ASK AN EXPERT

FIND DISTRIBUTOR

FIND DISTRIBUTOR

Surface protection is a major challenge for any industrial maintenance team. Harsh conditions damage SPECIFIC SUBSTRATES & protective coatings, putting safety and operations at risk.

PARTICULAR CONDITIONS HARD HAT® offers a wide range of industrial aerosols for any kind of surface. Applied quickly and easily, it We provide practical guidance for guarantees high quality protection that lasts longer. specific substrates (steel, wood, plastic,

Outdoor maintenance >

etc.) as well as particular conditions

We offer quick and easy solutions for daily maintenance (heat, cold, chemical deterioration, in and around any plant or building. We’ve got you covered for small touch-ups, specific surface marking orUV resistance, heavy wear, etc.). larger maintenance work. No matter what you’re working on, we have a HARD HAT® aerosol that does the job. This Search by substrate > product selector helps you choose the right aerosol to solve your challenge.

Search by condition >

FIND YOUR SOLUTION >

HARD HAT® RANGE

Scan the code to select your HARD HAT® product.

We offer quick and easy solutions for daily maintenance in and around any plant or building. Our product selector helps you choose the right aerosol to solve your challenge. Find the right product by scanning the QR code.

Want to explore the HARD HAT® range without having a specific application in mind? Check out our solutions by application category: Finishing > Galvanising > Surface preparing >

ASK AN EXPERT

FIND DISTRIBUTOR

Marking >

Indoor maintenance >

OUTDOOR MAINTENANCE UV-RESISTANT >

ANTI-CORROSION PROTECTION >

SPOT MARKING >

COLOUR IDENTIFICATION >

HORIZONTAL MARKING > LINE MARKING >

SAFETY MARKING >

THERE'S A HARD HAT® FOR EVERY PAINT JOB Surface protection is a major challenge for any industrial maintenance team. Harsh conditions damage protective coatings, putting safety and operations at risk. HARD HAT® offers a wide range of industrial aerosols for any kind of surface. Applied quickly and easily, it guarantees high quality protection that lasts longer.

We offer quick and easy solutions for daily maintenance in and around any plant or building. We’ve got you covered for small touch-ups, specific surface marking or larger maintenance work. No matter what you’re working on, we have a HARD HAT® aerosol that does the job. This product selector helps you choose the right aerosol to solve your challenge.

18

DURABLE TOPCOATS FOR ANY KIND OF CHALLENGE Need to freshen up colour, fluorescent, metallic or transparent coatings? Want to protect metal from rust patches or heat? The HARD HAT® Topcoats provide a durable solution for all these challenges. Easy to apply and fast drying, with durable coverage from minimal product.

HARD HAT® ADVANCED

HIGH-PERFORMANCE TOPCOATS

METALLIC TOPCOATS

FLUORESCENT TOPCOATS

TRANSPARENT TOPCOAT

HEAT RESISTANT TOPCOATS

HARD HAT ® TOPCOATS TOUCH-UPS IN SECONDS, TOPCOATS FOR YEARS

WWW.RUST-OLEUM.EU

19

HARD HAT® ADVANCED

PRIMER & TOPCOAT IN 1

HARD HAT® ADVANCED

Strong corrosion protection We saw the need for an ultra-performing aerosol that combines anti-corrosion with long-lasting protection, while being a primer and topcoat in one, and added this new kid on the block to our portfolio.

• • • •

Top quality Primer & Topcoat in 1 Strong corrosion protection High colour retention

2700 500 ml

Gloss Jet black

20

Matt Pure white

RAL 6005

RAL 5010

RAL 7035

RAL 7016

RAL 3000

RAL 1018

Transparent

Black

Satin White

Black

MADE TO PERFORM 1

PRIMER & TOPCOAT IN 1 No need to prime as the improved adhesion allows direct application on metal surfaces.

2

BETTER COLOUR RETENTION UV-resistant qualities ensure excellent colour retention, both indoors and outdoors.

3

MORE RESILIENT FINISH Stronger finish and highly elastic film without chips or cracks thanks to 10% more resin.

4

STRONG CORROSION PROTECTION Unique zinc-free anti-corrosive pigments keep surfaces rust-free much longer.

All colours are with anti-corrosive pigments

WWW.RUST-OLEUM.EU

21

HARD HAT® ORIGINAL

THE NR.1 INDUSTRIAL PAINT AEROSOL AVAILABLE IN ANY COLOUR (RAL, NCS, BS AND MORE)

HARD HAT® TOPCOATS

1. Go further More paint in the can, resulting in a higher coverage: 3-4 m2.

One HARD HAT® aerosol equals up to 2-3 standard aerosols.

2. Work quicker A higher film build without drips or runs, in one go twice the opacity of cheaper paint sprays (saving a cross layer). Normal coverage in one pass. Quicker drying: 10-15 minutes!

3. Last longer Higher quality pigments for a longer gloss and colour retention.

The tough flexible film resists chipping, cracking and peeling.

Available packsizes: 500 ml standard colours.

400 ml special colours on demand

22

HARD HAT® SPRAY FACTS 1

MORE PAINT IN THE CAN Propellant

3-4m2

Solvent Solids

Brand X

2

GREATER OPACITY! Brand X

3

RUST-OLEUM®

VS

RUST-OLEUM®

NO RUNS, NO DRIPS!

Brand X

VS

RUST-OLEUM®

WWW.RUST-OLEUM.EU

23

HARD HAT®

STANDARD COLOURS RAL 9006 2114

RAL 5012 2123

RAL 5005 2124

National blue 2125

RAL 5010 2126/2726

RAL 5002 2127

RAL 5003 2128

RAL 6018 2133

RAL 6032 2134

RAL 6011 2135

RAL 6001 2136

RAL 6005 2137/2737

RAL 6010 2138

RAL 1013 2141

RAL 1015 2142

RAL 1018 2143/2743

RAL 1023 2144

RAL 1028 2145

RAL 1021 2146

RAL 1003 2147

RAL 1007 2148

RAL 1004 2149

RAL 2003 2151

RAL 2002 2152

RAL 2000 2154

RAL 4001 2163

RAL 3000 2165/2765

RAL 3020 2166

RAL 8002 2174

Satin black 2176/2776

Matt black 2178/2778

RAL 9005 2179/2779

RAL 7035 2181/2781

RAL 7001 2184

RAL 7005 2186

RAL 7032 2187

RAL 7016 2189/2789

Matt white 2190/2790

RAL 9010 2192/2792

Satin white 2193

RAL 9001 2194

Transparent 2500/2750

RAL 9016 2196

Agricultural and Machine Colours 2126 Ford Blue, agricultural machinery 2133 Deutz Green, agricultural machinery 2136 John Deere Green, agricultural machinery 2143 John Deere Yellow, agricultural machinery 2145 Caterpillar Orange, excavators, dredging cranes

Safety Colours 2126 Fresh water 2134 Safe Place, escape routes, showers, exits 2143 Danger 2148 Take care/warning of danger, poison, explosion, radio-active radiation 2165 Stop/forbidden/fire extinguisher

2152 Linde Orange, excavators 2165 Massey Ferguson and New Holland Red, agricultural machinery 2186 Deutz Grey, agricultural machinery

24

2114 Steam 2123 Air 2138 Water 2149 Gas 2163 Acids and alkalis 2165

Fire fighting

2179 Other liquids

2148 JCB excavators 2154 STILL Orange, fork-lift trucks

Identification Colours

HARD HAT® Advanced 2700

HARD HAT®

SPECIAL COLOUR SERVICE • • • •

Trusted HARD HAT® quality 400 ml aerosol Any colour As of 9 pcs

ANY COLOUR IN 400ML AEROSOL RAL 2143

PIPELINE

BRITISH STANDARD BS1710 (PART 1. 1980)

IDENTIFICATION COLOURS Gas

RAL 1004 - HARD HAT® 2149 - CombiColor® 7349

Fire fighting

RAL 3000 - HARD HAT® 2165 - CombiColor® 7365

Air

RAL 5012 - HARD HAT® 2123 - CombiColor® 7323

Acids and alkalis

RAL 4001 - HARD HAT® 2163

Water

RAL 6010 - HARD HAT® 2138 - CombiColor® 7334

Other liquids

RAL 9005 - HARD HAT® 2179 - CombiColor® 7379

Steam

RAL 9006 - HARD HAT® 2114 - CombiColor® 7315

WWW.RUST-OLEUM.EU

25

HARD HAT®

SPECIALIST TOPCOATS HARD HAT® METALLIC TOPCOAT

Durable protection • • •

Gloss or sparkling metallic appearance To restore the metallic look of many different objects For use on bare metal, galvanised, zinc primers or anti-rust primers

METALLIC FINISH Finish with transparant topcoat 2500 for maximum gloss and durability

Spark ling Alu

White Alu

2111 500 ml

2114 500 ml

Alu

HARD HAT® STAINLESS STEEL COATING

Double-acting protection (chemical & mechanical) • Greater abrasion resistance • Better anti-corrosion properties than other metallics • Excellent UV resistance (does not discolour) • Resists acids, chemicals and alkalis

EXTRA STRONG FINISH Application tips for different substrates: - On stainless steel: roughen the surface + 2116 - On slightly rusty surfaces: 2169 + 2116 - On zinc/galvanised: 2185/2180 + 2116 Stainless steel

26

2116 500 ml

2115 500 ml

HARD HAT® FLUORESCENT TOPCOATS

Ideal for stencils, safety markings and colour coding

HIGH VISIBILITY For maximum efficiency of fluorescent colours, spray over HARD HAT® matt white (2190) and finish with HARD HAT® clear coat (2500), see below

2200 500 ml

2222

2233

2264

2242

2255

Fluo blue

Fluo green

Fluo red

Fluo yellow

Fluo orange

HARD HAT® TRANSPARENT PROTECTION

Protects copper, chrome, silver bronze, nickel, aluminium • Non-yellowing (UV-resistant) • Quick drying (10-15 min.)

Application areas: • Protective layer for many metal surfaces • Gloss repair of old coatings • Provides extra durability to metallic and fluorescent coatings TRANSPARENT PROTECTION

2500 500 ml

Clear

WWW.RUST-OLEUM.EU

27

HEAT RESISTANT

COATINGS

HARD HAT® HEAT RESISTANT

For temperatures up to 750oC HARD HAT® 7715 and 7778 heat resistant coatings should be used on new, bare steel, blasted steel or light rusted steel surfaces or properly prepared painted substrates alike barbecue grills, fire place equipment, space heaters etc. Provides heat resistance up to 750°C dry heat (short term peak resistance) in sheltered or interior environments.

7778 500 ml

7715 500 ml

1015 / 1078 750 ml - 2,5 L

Aluminium

28

Matt black

RESULTS AFTER 2 HOURS AT 600˚C

Competitor 1

Competitor 2

Available sizes:

HARD HAT® 7778

Spray 500 ml Brush version 750 ml & 2,5 L

For use on: • Engines • Heat cannons • Steam pipes • Boilers • Vents • Barbecues • Stoves

WWW.RUST-OLEUM.EU

29

SUPERGRIP™

EASILY PREVENT SLIPS AND TRIPS

ALSO IDEAL FOR GRIPS & HANDLES ANTI-SLIP SPRAY

Makes every surface non-skid in a second • Light duty anti-slip finish • Adheres to metal, wood, concrete, tile floors and parquet • Very quick drying (5-10 minutes)

For a more durable anti-slip finish, see Rust-Oleum® 7200 Floorcoat NS and Supergrip™ Treadsafe.

2479 Black

30

2444

Safety yellow

2410

Transparent

2400 500 ml

BRIGHT AND DURABLE MARKING SPRAYS HARD HAT® Marking aerosols are bright-coloured sprays for line and spot marking, horizontal or vertical. Easily applied on diverse and uneven surfaces, with short drying times.

LINE MARKING

FLOOR MARKING

360° MULTI MARKER

HARD HAT ® MARKING MARK ANY SURFACE IN ANY COLOUR

WWW.RUST-OLEUM.EU

31

LINE MARKING PAINT

UP TO 120 METER PER CAN!

HARD HAT® LINE MARKING PAINT

Durable line marking paint Ideal for drawing lines in parking areas, plants, warehouses, sports fields, stadiums and all sites where traffic control is required. HARD HAT® lining paint should be used in light traffic exposure.

The product is designed for use together with the RUST-OLEUM® Striping Machine.

• • • • •

For use with RUST-OLEUM® line applicators Adjustable line width from 5 to 10 cm Light traffic possible after just 4 hours Adheres to asphalt, concrete, grass, metal, wood, etc.

2391 & 2348 also available in 500 ml

2300 500 ml - 750 ml 2391 RAL 9010

32

2348 Yellow

RAL 5017

RAL 3020

RAL 6024

RAL 9017

RUST-OLEUM® LINE APPLICATORS A Handle V2009

B Handle + 2-wheels V2009+2005

C Handle + 4-wheels V2009+V2029

WHY BETTER?

D Competitor

Handle + 4-wheels V2009 + V2029 (sideholder included with V2029)

Rust-Oleum® • Sharper line edges • Better opacity

Corridors, lanes, work zones and traffic lanes for vehicles Materials and parts, including raw materials, semi-finished products and finished products Materials for inspection

source: 5S method

Optimise safety and efficiency

Defective parts, waste, rework

WWW.RUST-OLEUM.EU

33

PERFORMANCE MARKING PAINT

UP TO 70 METER PER CAN! HIGHEST OPACITY

HARD HAT® FLOOR MARKING

Best quality marking paint • • • • •

For marking difficult substrates Best opacity, weather-resistant and watertight For on metal, concrete, asphalt, gravel, soil, grass, wood, etc.

Even on slightly wet surfaces Upside down spraying system

2358 500 ml

Fluo red/ orange

34

Yellow

White

2392 500 ml

2344 500 ml

360° MULTI MARKER

2 -3

SPRAYABLE IN ALL DIRECTIONS

0 ˚

cm

36

360° MULTI MARKER

Fluorescent colours • • • •

2822 500 ml

2833 500 ml

2864 500 ml

2842 500 ml

2862 500 ml

Optimised for ground marking Spray through cap for ease of use Easier writing Quick drying (5 - 10 minutes)

2855 500 ml

Fluo blue

Fluo green

Fluo red

Fluo yellow

Fluo pink

Fluo orange

360° MULTI MARKER

RAL traffic colours • • • •

2896AE.0.75 750 ml

2844AE.0.75 750 ml

2866AE.0.75 750 ml

Optimised for ground marking Extra large can for more linear metres Two finger nozzle for accurate writing Quick drying (5 - 10 minutes)

2824AE.0.75 750 ml

RAL 9016

RAL 1023

RAL 3020

RAL 5017

WWW.RUST-OLEUM.EU

35

SPRAY TOOLS

FOR AN EASIER JOB

WATCH THE VIDEO

HARD HAT® SPRAY GRIP®

Spray with ease!

• Ergonomic design • Large soft touch trigger

Attach by squeezing with two fingers

V241526

36

Align spray tip through opening

• Durable construction • For all HARD HAT® aerosols

Purge aerosol to clean nozzle

THE SECRET TO SUCCESSFUL SPRAYING 1 Surface preparation

Clean

Degrease

Dry surface

2 Test before use!

Each aerosol paint performs differently due to the hardware, thickness of the paint inside, propellant, etc. Make sure to test spray the can to determine the optimal spraying distance, the speed of application, etc. before spraying the actual object.

OBJECT

OBJECT

step 1

step 2

Always apply cross layers.

3 Movement and distance 20-25 cm

The secret to achieving even coverage is keeping your wrist locked. Keep the can parallel from the object at 20-25 cm and move the can back and forth, creating equal passes.

4 Clean the nozzle To clean the nozzle after use, always turn the can upside down and spray until transparent propellant comes out. It may look like a waste, but it prevents blocking of the aerosol, making it available for future use again.

WWW.RUST-OLEUM.EU

37

COMBICOLOR ORIGINAL ®

PROTECTION AL

CY

ME T

DIRECT TO RUST!

LIF N E EXPECTA

COMBICOLOR® ORIGINAL

Time saving paint for metal protection • • • • •

Available pack sizes: 250 ml, 750 ml, 2,5 L, 400 ml aerosol

38

Primer and topcoat in one For application onto rust, bare metal High coverage: 10.3 m² per litre Sag resistant, no brush strokes Usable down to 5°C

COMBICOLOR® ADVANTAGES A PRIMER AND TOPCOAT IN ONE

AVAILABLE IN ANY COLOUR (RAL, NCS, BS AND MORE)

B LONGER LASTING FLEXIBILITY

Brand X

®

C GREATER OPACITY! Standard 7301

For hammertones 7302

CombiColor® Thinners CombiColor® coatings are ready for immediate use with brush or roller. For spray application however it is advised to use a CombiColor® thinner.

Brand X

®

WWW.RUST-OLEUM.EU

39

COMBICOLOR®

Gloss

STANDARD COLORS

7344 RAL 1023

7389 RAL 7016

7396 RAL 9016

7341 RAL 1013

7314 Gold

7315 RAL 9006

7323 RAL 5012

7324 RAL 5015

7326 RAL 5010

7328 RAL 5002

7329 RAL 5011

7333 RAL 6018

7334 RAL 6010

7335 RAL 6011

7336 RAL 6001

7337 RAL 6005

7339 RAL 6009

7342 RAL 1015

7343 RAL 1018

7346 RAL 1021

7348 RAL 1007

7349 RAL 1004

7354 RAL 2000

7365 RAL 3000

7366 RAL 3020

7373 RAL 8001

7377 RAL 8011

7379 RAL 9005

7381 RAL 7035

7382 RAL 7001

7362 Copper

7364 Red

Satin 7383 Silver gray

7386 RAL 7005

Matt

7392 RAL 9010

7347 RAL 1003

Wrought Iron

Hammertones

7320 RAL 5017

7375 Black

7394 White

7338 Dark green

7345 Gold

7378 Black

7390 White

7319 Black

7321 Light blue

7332 Light green

7374 Dark brown

7376 Black

7384 Light grey

7388 Dark grey

7391 White

There may be some slight variation from original manufacturer’s colours.

Agricultural and Machine Colors

Identification Colors (See page 21)

Safety Colors

7326 Ford Blue, agricultural machinery

7315 Steam

7326 Fresh water

7333 Deutz Green, agricultural machinery

7323 Air

7343 Danger

7336 John Deere Green, agricultural machinery

7334 Water

7348 Take care/warning of danger, poison,

7343 John Deere Yellow, agricultural machinery

7349 Gas

7348 JCB excavators

7365 Fire fighting

7354 STILL Orange, fork-lift trucks

7373 Combustible liquids

7365 Massey Ferguson and New Holland Red,

7379 Other liquids

explosion, radio-active radiation 7365 Stop/forbidden/fire extinguisher

Aqua colors

agricultural machinery 7386 Deutz Grey, agricultural machinery

Non-Zinc colors

CombiColor® coatings can be supplied on special request, in more than 25.000 RAL, AFNOR, NCS, BS381C and BS4800 colours (gloss and satin).

40

COMBIPRIMER® ANTI-RUST PRIMER

For an even longer anti-rust protection • Recoatable after 2 hours • For new / slightly rusted surfaces

1

DIRECT TO RUST

• Grey for light coloured topcoats • Red for dark coloured topcoats

2

Remove loose rust with a wire brush

3

Clean and degrease

Apply CombiPrimer® (3369/3380)

Available pack sizes: 250 ml, 750 ml, 2.5 L, 400 ml aerosol

Red brown

Grey

COMBIPRIMER® ADHESION PRIMER

Makes even the smoothest surface coatable • Easy to apply • Transparent blue finish

1

FOR EXTRA ADHESION

Clean & degrease surface

• Recoatable after just 30 minutes • Very high coverage: 50 m2/l.

2

Apply CombiPrimer®

3

Apply CombiColor® topcoat

Available pack sizes: 250 ml, 750 ml, 400 ml aerosol

Transparent blue

WWW.RUST-OLEUM.EU

41

COMBICOLOR® MULTI-SURFACE

ONE PAINT, MANY SURFACES

AVAILABLE IN ANY COLOUR (RAL, NCS, BS AND MORE)

COMBICOLOR® MULTI-SURFACE

All-in-one paint (primer + finish) • • • •

Direct to surface Paint & primer in one Quick drying Interior and exterior

750 ml - 2,5 L

RAL 7006

42

RAL 1007

RAL 1015

RAL 1018

RAL 3000

RAL 5010

9m2/L

RAL 6005

RAL 9005

RAL 9005 satin

RAL 7035

RAL 7016

RAL 9001

RAL 9001 satin

RAL 9010

RAL 9010 satin

RAL 9016

RAL 9016 satin

RAL 7001

Matt black

Matt white

FOR DIRECT APPLICATION TO MANY SURFACES

Tiles

Wood

Masonry

Inox

PVC

Concrete

And more...

For a full view of all application areas please refer to the technical data sheet (www.rust-oleum.eu).

WWW.RUST-OLEUM.EU

43

COMBICOLOR AQUA WATER-BASED FORMULA An anti-corrosion metal paint that uses the very latest paint technology in a waterbased formula that is safer for the user and the environment whilst maintaining the same flexibility, flow, weather resistance and high performing metal protection as our CombiColor® Original. Containing rust-inhibitive additives, the low VOC, water-based formula is lead and chromate free. A 2-in-1 paint, it can be applied to any metal surface (including directly to rust) without the need for a primer.

The paint film is designed to resist cracking, peeling and blistering for up to 12 years before first maintenance. Apply directly to bare, previously painted or rusted ferrous metal.

For metal structures in a more aggressive industrial environment, prior application of CombiColor® Aqua Primer is recommended.

10 m²/L

12 RAL COLOUR TOPCOATS AND 2 ANTI-RUST PRIMERS GLOSS

RAL 1015

RAL 1018

RAL 3000

RAL 5010

RAL 5012

RAL 6005

RAL 7001

RAL 7005

RAL 7016

RAL 7035

RAL 9005

RAL 9010

ANTI-RUST PRIMER

SATIN

RAL 9005

RAL 9010

3369AQ. 0.75

• Water-based • Direct to rust • Interior & exterior use • All-weather resistant • Sag resistant • Can be applied at low temperatures from 10°C

Available in 750 ml Due to printing limitations, colours shown may differ from actual products.

44

3380AQ. 0.75

®

AQUA

PROTECTS METAL, THE PLANET AND YOU!

AQUA WATER BASED

WATER-BASED TECHNOLOGY

INTERIOR & EXTERIOR USE

EXCEPTIONAL COVERAGE & FLOW

LOW ODOUR LOW VOC

DIRECT TO RUST

www.combicolor.eu or contact your local distributor

WWW.RUST-OLEUM.EU

45

COMBICOLOR® NON-ZINC

12 RAL COLOUR TOPCOATS AND 2 ANTI-RUST PRIMERS

Limiting the health and environmental impact whilst increasing metal protection from rust seems contradictory, however our revolutionary CombiColor® formula now incorporates non zinc, anti corrosive additives that replace the traditional zinc phosphate additives. It is also lead and chromate free.

CombiColor® Non-Zinc can be applied directly to rust. It offers outstanding anti-corrosive performance for up to 12 years*, as well as excellent flexibility, flow and weather resistance - all of the qualities that Rust-Oleum® CombiColor® is known for.

GLOSS

RAL 1007

RAL 3000

RAL 5010

RAL 6005

RAL 7001

RAL 7005

RAL 7016

RAL 7035

RAL 9005

RAL 9006

RAL 9010

RAL 9016

ANTI-RUST PRIMER

SATIN

For metal structures in a more aggressive industrial environment, prior application of CombiColor® Non-Zinc Primer is recommended.

RAL 9005

RAL 9010

3369ZF. 0.75

*The paint film is designed to resist cracking, peeling and blistering for up to 12 years before first maintenance.

• Non-zinc anti-corrosive additives • Interior & exterior use • Sag resistant • All-weather resistant • Direct to rust • No brush strokes • Heat resistant up to 90°C • Can be applied at low temperatures from 5°C Available in 750 ml Due to printing limitations, colours shown may differ from actual products.

46

3380ZF. 0.75

®

NON-ZINC

STRAIGHT FROM THE FUTURE

ADVANCED FORMULA WITH

NON ZINC ANTICORROSIVE ADDITIVES

NON-ZINC ANTI-CORROSIVE ADDITIVES

INTERIOR & EXTERIOR USE

EXCEPTIONAL COVERAGE & FLOW

EXCELLENT FLEXIBILITY

DIRECT TO RUST

www.combicolor.eu or contact your local distributor

WWW.RUST-OLEUM.EU

47

COVERS ALL AREAS We offer quick & easy solutions for daily maintenance around any factory or building. From small touch-up repairs to full scale renovations.

Zinc sprays Page 13

Instant roof repair Page 64-65

Metal paint Page 38

Asphalt restorer Page 63 Anti-slip paint Page 30

Heavy duty floor coatings Page 55

48

Large scale renovation?

We also offer a full range of products and solutions to cover your large scale maintenance and renovations works. From metal cladding rejuvenation, a new heavy-duty floor coat, full roof renovation or more challenging maintenance and renovation projectcs.

• From colour change to complete renovation • Minimal downtime thanks to quick drying coatings • Extensive network of approved coating contractors • Free technical advice and on-site inspection • Up to 10 years warranty possible

Light duty floor coatings Page 52

Anti rust primer Page 59

Check our High Performance catalog

Heat resistant Page 28

Fluo marking Page 35

Floor coatings Page 54

Exterior floor paint Page 58

Anti-graffiti protection Page 76-77 Asphalt repair Page 62 Line marking Page 32 Technical sprays Page 68

Instant leak seal Page 66

WWW.RUST-OLEUM.EU

49

EXTERIOR FLOOR PAINT

QUICK DRYING

TARMACOAT™

Quick drying exterior floor paint • • • • •

Rainproof and walkable after one hour!

Very easy to apply Apply on slightly damp surface Water-based formula Single pack paint

Asphalt

Concrete

Sport fields

6100 5L

8m2/L

English Red

50

RAL 1023

RAL 3020

RAL 5017

RAL 6010

RAL 7005

RAL 7035

RAL 9016

RAL 9017

SHOPPRIMERS

A BASIC ANTI-CORROSION PROTECTION

6400 SHOPPRIMER

Ideal for workshops and construction companies • Excellent adhesion to metal • Solvent based • Ideal for spray application • Recoatable with CombiColor® and many other coating systems • Masks construction deficiencies

6400 5 & 20 L

Red brown

Grey

Black

WWW.RUST-OLEUM.EU

51

PU REINFORCED FLOOR COATING

HARD WEARING, EASY TO APPLY

7200 FLOORCOAT PU

Single pack PU • Extra durable because of polyurethane addition • Excellent flow • Any colour in Gloss and Satin • Light to medium traffic, indoor/outdoor • High coverage: 9 m2/L per coat • Also ideal for line marking

Available in 5L and 20L Colourshop: 2,5L, 5L and 10L

9m2/L

RAL 1023

RAL 7001

RAL 7035

RAL 9005

Transparent

Important: Not suitable for car traffic or for car park areas (see EpoxyShield®)

Gloss and Satin: Available in almost any colour upon request (RAL, BS, AFNOR, etc.)

7200NS FLOORCOAT PU

52

RAL 7001

RAL 7035

RAL 9005

RA DÉ AN TI-

H

RAL 1023

SC UT

9m2/L

R TI-

For foot traffic, interior and exterior Anti-slip additive is premixed in the coating For use on concrete, metal and wood Touch dry after 4 hours Apply a 2nd coat to increase the antislip properties

AN

• • • • •

PA N

T

Single pack anti-slip

ANTI-SLIP

5L

Transparent

HOW TO APPLY EASILY 1 Clean the floor

2 Apply 7200 PU/NS

PRE-PAINTED FLOORS

CONCRETE FLOORS (POROUS)

WOODEN FLOORS (INTERIOR)

METAL (INTERIOR)

3 Allow to dry

WWW.RUST-OLEUM.EU

53

EPOXYSHIELD®

WATER BASED INDUSTRIAL FLOOR COATINGS

EPOXYSHIELD®

Quick & easy to use!

• Ease of choice • Ease of application • Water based formulas • Maximum durability

Standard

54

Anti-Slip

Decorative

CHOOSE YOUR PERFECT FLOOR ...IN 3 EASY STEPS! 1 Choose protection level SEALER Dust proofing

ULTRA

Light-Medium traffic

MAXX

Medium-Heavy traffic

2 Choose colour

RAL 7001

RAL 7035

RAL 1015

ENGLISH RED

EA

USE • WATER QUE BA

SI

EpoxyShield Maxx + Anti-Slip additive

EpoxyShield Maxx + Decorative

ERBASSIERT ASS •W

ER BASED • E WAT NP

AS

S

H

3 Choose finish (optional)

All EpoxyShield coatings are water-based. Ideal for interior applications.

Anti-Slip

Decorative

WWW.RUST-OLEUM.EU

55 6

EPOXYSHIELD®

WATER BASED INDUSTRIAL FLOOR COATINGS CLEANER / DEGREASER

Ready to use for floors • Removes grease, oil and other contaminations • Virtually odour free • Non-flammable • 6-8 m²/l coverage

2901.5 5L

EPOXYSHIELD® SEALER

The excellent dust-proofer water based, cost effective • • • • •

9m2/L

Clear

56

DUST PROOFING

Single pack, easy to apply Non yellowing clear finish (gloss) Protects against moisture and road salts Touch dry after just 1 hour Ideal primer for EpoxyShield® ULTRA coatings

5220 5L

EPOXYSHIELD® ULTRA

Quick drying floor coating Single pack, water based LIGHT-MEDIUM TRAFFIC

• • • • •

For light to medium traffic Easy to apply Touch dry after just 2 hours Satin matt finish Good resistance to car tyres and various chemicals

5200 5L

9m2/L

RAL 7001

RAL 7035

English Red

EPOXYSHIELD® MAXX

Maximum durability 2-pack water based Epoxy

MEDIUM-HEAVY TRAFFIC

• • • • • •

For medium to heavy traffic Easy to apply, no primer required Long-lasting gloss finish Best possible car tyre resistance Highly resistant against solvents and chemicals Non-skid or decorative finish optional

5300 5L

7 m2/L

RAL 1015

RAL 7001

RAL 7035

English Red

WWW.RUST-OLEUM.EU

57

EPOXYSHIELD®

SURFACE PREPARATION & FINISHES EPOXYSHIELD®

Anti-slip additive For use with EpoxyShield® MAXX only

200.0.7

RAL 7001

RAL 7035

RAL 1015

English Red

EPOXYSHIELD®

Decorative Chips For use with EpoxyShield® MAXX only

505.0.43

RAL 1015

58

RAL 7001

RAL 7035

English Red

ONE KIT FOR 25 m2 INCLUDES: • 2-part epoxy floor system • Concentrated cleaner • Decorative chips • Detailed instructions

EPOXYSHIELD® MAXX

Garage floor coating

25 m2

• •

2-pack water based epoxy Complete kit including instructions

1

203005.3.78 3,55 L

•

esists gasoline, antifreeze, R motor oil, salt and hot tire pick-up

2

3

25m²/L

Gray

CONCRETE REPAIR MORTAR

FREE INCLUDED IN KIT

Simply add water, stir and apply • Traffic allowed after 24 hours • Recoatable after 48 hours • 10 kg (1-component) – 0.4 m² • Sandable to a smooth finish

203012.10 10 Kg

Not to be recoated with 7100 Floor coating!

WWW.RUST-OLEUM.EU

59

STRONG

CONCRETE REPAIR

Stronger than concrete!

EPOXY REPAIR MORTAR

Quick & easy concrete repair Very strong epoxy repair mortar for repairing damaged floors.

Stronger than concrete!

• Stands up to heavy traffic and many chemicals • For repairing eroded or damaged concrete, bay edges and broken steps • Does not shrink or crack • Easy all-in-1 packaging • For indoor and outdoor use • Quickly back into service

5180 Available in 2,5 - 5 - 25 Kg

Dark grey

60

DEEP

CONCRETE REPAIR

Suitable for • Floors • Steps • Ramps

EPOXY REPAIR

Mortar Deep Fill Very strong epoxy repair mortar for quick and economical repair of deep holes in concrete floors.

• Economical repair of holes of 15 - 100mm deep • Resistant to oils and chemicals • Does not shrink or crack • Easy all-in-1 packaging • For indoor and outdoor use

5190.25

Dark grey

WWW.RUST-OLEUM.EU

61

QUICK ASPHALT REPAIR

FOR POT-HOLED ASPHALT AND CONCRETE

ASPHALT REPAIR

Immediate pot-hole repair Rust-Oleum® Asphalt Repair is a durable bitumen-based patch repair product for use on exterior pot-holed asphalt and concrete. Ideal for potholes in roads, car parks, paths and other bituminous and concrete surfaces.

• • • • •

Simple to use - no mixing required Repairs can be driven over immediately after application Ideal for repairs 10 mm – 70 mm Coverage approx. 0.5 m² per 25 kg at 24 mm thick Withstands heavy traffic

1

2

Apply primer

3

Fill

Compact

5410.25 25 kg

Black

62

SINGLE PACK BITUMEN PAINT

FRESHENS UP DISCOLOURED ASPHALT

ASPHALT RESTORER

Makes asphalt look like new again A single application, refurbishing coating for car parks, driveways and footpaths, bicycle paths and more.

• • • •

Upgrades drab, grey, stained asphalt and tarmac Provides an ‘as new’ appearance Covers old line markings and repairs Avoids disruptive and costly re-surfacing

Rust-Oleum® Asphalt Restorer is a one component high quality bitumen based coating with fillers and special flow additives. For refurbishing car parks, driveways and footpaths.

5478.5 5L

Black

WWW.RUST-OLEUM.EU

63

INSTANT WATERPROOFING

EVEN IN BAD WEATHER!

FILLCOAT® WATERPROOFING

Stops leaks instantly • • • • • •

64

Better UV resistance Immediate waterproofing of roofs and gutters Even in cold, rainy weather For bitumen, PVC, metal, tiles and glass Remains flexible in hot and cold conditions Renovation of weathered roofs

CRACK BRIDGING

FILLCOAT®

Original formula without fibres • Thick waterproof coating • Excellent adhesion to various substrates • Renovation of weathered roofs • Smooth appearance • Apply with brush, roller or airless

1 - 5 - 20 L

1 m²/L

Light grey

Dark grey

Black

FILLCOAT® FIBRES

With crack bridging fibres • Repairs holes and cracks up to 2mm • Stops leaks instantly • Faster than calling the plumber or roofer • Excellent adhesion • Brush applied

1 - 5 - 20 L

1 m²/L

Light grey

Dark grey

FILLCOAT® FIBRES REPAIR KIT

Everthing you need in one kit • Can of FILLCOAT® FIBRES • Brush & Gloves • Crack bridging fleece • Sanding block • Instruction sheet

1 m²/L

Dark grey

WWW.RUST-OLEUM.EU

65

LEAKSEAL™

FLEXIBLE RUBBER COATING

LEAKSEAL™

Quickly seals leaks and cracks • • •

500 ml

White

66

Black

Transparent

Aluminium

Watertight semi smooth finish Can be top-coated with latex or oil-based paints For use on metal, aluminum, PVC, concrete, masonry, asphalt roofing materials, etc.

LEAKSEAL™

WERE CAN IT BE USED? 1 Roof chimney stacks

2 Gutters pipes/ducts

Also ideal for creating a rubber-like impact resistant surface

3 Window joints etc.

WWW.RUST-OLEUM.EU

67

X1 COVERS IT ALL!

THE NEXT GENERATION TECHNICAL SPRAYS

Pantone 8200 C Pantone 871 C

For the best lubrication and preservation of machines, tools and workpieces Rust-Oleum ® has revolutionised technical sprays with a special additive: ‘BoroTecX ™’ the ultimate in lubrication improving additives.

68

Re

i

orced w

BoroTecX Nitr

id

rp he

erform a

BoroTecX 900˚ C

nc

Grafite 450˚ C

e

Hig

ron

TM

e

Bo

BoroTecX ™ The ultimate equipment protection!

ith

nf

MoS2 400˚ C PTFE 250˚ C

BoroTecX™ is capable of withstanding temperatures up to 900°C

No BoroTecX™ orced w

Re

nf

BoroTecX

TM

id

e

ron

Nitr

protect io ter t e

n

B

Bo

BoroTecX™ is capable of withstanding extreme loads.

Where others fail, BoroTecX™ continues and keeps reducing friction.

ith

i

eL trem oads x E

BoroTecX™ is highly chemical resistant. It therefore can be used in chemical (aggressive) areas.

sts longer

orced w

Re

nf

ith

i

La

BoroTecX ron

id

e

Bo

Nitr

TM

No BoroTecX™

Test EN ISO-20623 / ASTM D2266 has proven that X1 white grease containing BoroTecX™ can outperform standard greases by up to 4 times.

Available packsize: 500 ml

WWW.RUST-OLEUM.EU

69

For the best lubrication and preservation of machines, tools and workpieces

• •

Grease

• •

Dry lubricant Stops squeaking

•

•

Adhesive Creeping

•

Removing rust Anticorrosive Displaces water Water-repellent Protecting Cleans Cooling High temperature

70

• • • • •

•

• • • • •

•

• • •

• • •

• •

•

•

1618 X1 PTFE spray

• •

1617 X1 White Grease spray

• •

1616 X1 Ceramic Anti Seize spray

•

1615 X1 Silicone spray

• •

1614 X1 Freeze & Release spray

Penetrating

1612 X1 Chain & Drive spray

Lubricates

1611 X1 Cutting & Tapping spray

1610 X1 Multi-Purpose spray

Pantone 8200 C Pantone 871 C

•

• •

•

•

• •

• •

•

• •

MULTI-PURPOSE SPRAY

Lubricates, cleans and protects

BoroTecX Bo

ron

CORROSIVE

P EN

ETRATING

RICATING LUB

TECTING PRO

CLEANING

˚ SYSTEM 360

TM

id

e

1610

TI AN

orced w

Re

nf

ith

i

• Stops squeaking • Creeping properties • Displaces water • A film layer is left on the surface after cleaning • Does not contain silicon • Temperature range: -30 °C to 145 °C • Dissolves grease, tar, oil and some adhesives

Nitr

WWW.RUST-OLEUM.EU

71

CUTTING & TAPPING SPRAY

Lubricates and cools all cutting tools

BoroTecX ron

TM

1611

id

e

Bo

RICATING L UB

orced w

Re

nf

ith

i

• Prolongs tool life • Reduced friction leads to better surface finish • Increases process speeds • Temperature range: -30 °C to 130 °C

Nitr

CHAIN & DRIVE SPRAY

Reduces friction, helps prevent wear

BoroTecX

ETRATING

RICATING L UB

TECTING PRO

˚ SYSTEM 360

ron

TM

1612

id

e

Bo

P EN

orced w

Re

nf

ith

i

• Good adhesion • Resists detergent washing • H1 compliant for incidental food contact • Temperature range: - 35 °C to 180 °C

Nitr

FREEZE & RELEASE SPRAY

High quality rust releaser with shock effect

BoroTecX

72

ron

id

e

Bo

TI AN

orced w

Re

nf

CORROSIVE

P EN

ETRATING

RICATING LUB

TECTING PRO

˚ SYSTEM 360

ith

i

• Water repellent • Temperature range: -50 °C to 170 °C • Shocks components with rapid temperature reduction

Nitr

TM

1614

SILICONE SPRAY

Odourless and colourless dry lubricant

BoroTecX Bo

ETRATING

RICATING L UB

TECTING PRO

˚ SYSTEM 360

ron

TM

id

e

1615

P EN

orced w

Re

nf

ith

i

• Dry lubricant • Stops squeaking • Water resistant and repellent • Temperature range: –40 °C to 200 °C

Nitr

CERAMIC ANTI SEIZE SPRAY

Protection of all threaded fasteners

BoroTecX Bo

ron

CORROSIVE

P EN

ETRATING

RICATING L UB

TECTING PRO

˚ SYSTEM 360

TM

id

e

1616

TI AN

orced w

Re

nf

ith

i

• Prevents seizing and galling • Withstands extreme temperatures: - 30 °C up to + 1100 °C • Water, chemical and weather resistant • Insulates, prevents seizure between dissimilar metals

Nitr

Pantone 8200 C Pantone 871 C

WWW.RUST-OLEUM.EU

73

WHITE GREASE SPRAY

Withstands extreme loads and conditions

BoroTecX

CORROSIVE

P EN

ETRATING

RICATING LUB

TECTING PRO

˚ SYSTEM 360

ron

TM

1617

id

e

Bo

TI AN

orced w

Re

nf

ith

i

• Stops squeaking • Water repellent • Corrosion preventive • Suitable for vertical surfaces, will not run

Nitr

PTFE SPRAY

Light lubricant containing PTFE

BoroTecX

74

ron

id

e

Bo

P EN

orced w

Re

nf

ETRATING

RICATING LUB

TECTING PRO

˚ SYSTEM 360

ith

i

• High anti-wear characteristics • Contains PTFE • Water repellent • Ultra low friction coefficient • Temperature range: -40 °C to 120 °C

Nitr

TM

1618

Pantone 8200 C Pantone 871 C

WWW.RUST-OLEUM.EU

75

THE PERFECT

ANTI-GRAFFITI PROTECTION PERMANENT SYSTEMS A permanent anti-graffiti barrier allows for multiple graffiti cleaning processes using a special cleaner before the layer itself should be renewed. In other words ideal for regularly attacked placed that require frequent cleaning. It normally consists of several layers to reach the required protection level.

See GraffitiShield™ HYDRO for more information.

TEMPORARY SYSTEMS (SACRIFICIAL) Depending of the surface and the conditions a temporary (sacrificial) or permanent protection layer can be chosen. Sacrificial means the layer itself will be completely removed together with the graffiti during every cleaning process using high pressure cleaning with hot water.

The protective layer should be re-applied after cleaning. RUST-OLEUM® uses a natural wax for this system, making it an environmentally friendlier alternative to permanent systems. Even more so because no special chemical cleaners are required.

See GraffitiShield™ WAX for more information.

GRAFFITI SHIELD™ POLYCOAT

Anti-graffiti coating Single pack solvent-free anti-graffiti protection for many indoor and outdoor substrates.

• Hard, smooth surface makes it • Transparent protection easy to clean any graffiti on it • Also useful as a colourless • Solvent-free, low odour varnish for floors

57104 2,5 - 5 L

76

EA

USE • WATER QUE BA

Sacrificial system

SI

RBASSIERT ASSE •W

ER BASED • E WAT NP

AS

S

H

GRAFFITI SHIELD™ WAX

Sacrificial layer based on natural wax.

Suitable for a single cleaning process • Virtually invisible • Biodegradable • Low on solvents

• Water vapour permeable • Immediately graffiti-proof • UV-resistant

MINERAL SUBSTRATES

57101.10 1-Component Water-based

EA

USE • WATER QUE BA

Permanent system

SI

RBASSIERT ASSE •W

ER BASED • E WAT NP

AS

S

H

GRAFFITI SHIELD™ HYDRO

Water based permanent anti-graffiti coating with hydrophobic properties • Virtually invisible • No film-building • Excellent UV-resistance

• Water vapour permeable • Waterproof (Hydrophobic) • Ideal for natural stone

MINERAL SUBSTRATES

57102.10 1-Component Water-based

WWW.RUST-OLEUM.EU

77

LARGER OR CHALLENGING PROJECT?

WE CAN HELP!

Metal protection in harsh environments

Metal cladding rejuvenation & renovation

Large scale heavy-duty floor protection

Full roof renovation

Specialist coatings for hygienic environments

Waterproofing of exterior walls

FREE

ADVICE OR SITE VISIT!

INSPECTION ON-SITE We also offer a full range of products and solutions to cover your large scale maintenance and renovations works. From metal cladding renovations or more challenging maintenance or renovation projects, applying a new floor coat, full roof renovation, etc.

• From colour change to complete renovation • Minimal downtime thanks to quick drying coatings • Extensive network of approved coating contractors • Free technical advice and on-site inspection • Up to 10 years warranty possible

78

SUBSCRIBE TO OUR

NEWSLETTER

REGISTER NOW!

• Get exclusive tips • View application videos • Win great gadgets • Keep up-to-date on new products and services

Also check our other news channels:

@RustOleumEU

/RustOleumEU

/RustOleumEU

WWW.RUST-OLEUM.EU

79

Find your nearest Rust-Oleum distributor: www.rust-oleum.eu/distributors or contact our customer service team.

/RustOleumEU

5 413436 074975

/RustOleumEU

Tor Coatings Ltd (Rust-Oleum Industrial) UK

Rust-Oleum Europe

+44 (0) 191 411 3146 info.uk@rustoleum.eu

+32 (0) 13 460 200 info@rustoleum.eu

RUST-OLEUM® products are manufactured by Rust-Oleum Europe under license from Rust-Oleum International Corporation, USA. RUST-OLEUM® is a registered trademark of Rust-Oleum International Corporation, USA. The guidelines in this brochure are provided for information purposes only. Since the manufacturer is unable to exercise any control over the correct application and processing of the products, he cannot accept any responsibility for this.

For more product information, like Product Data Sheets & Safety Data Sheets, view our online information on our website www.rust-oleum.eu. © Copyright 2024 Rust-Oleum Europe. All rights reserved. The images shown in this catalogue may differ from the actual product.

KNOW-HOW TO PROTECT™

V350.GB - 2024-12

WWW.RUST-OLEUM.EU