Pixelscreen beginners guide building quick & safe. 01.01.2018

UPDATE 01.01.18

PIXELSCREEN.eu QUICK-GUIDE

WHAT IS WHAT LEDPANELS Page 4 CAMERA / JOYSTICK Page 51 CABLES Page 54 DISTRIBUTION Page 60 SENDER SYSTEMS Page 62 RIGGING Page 64

HOW TO BUILD ART OF DAMAGE-CONTROL READING PLANS PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 68

Page 70 Page 80

Page 2

PIXELSCREEN.eu QUICK-GUIDE

SCALERS Page 92 LOGISTICS Page 94 CHECK & SEALS Page 98 SAFETY Page 100 PERSONAL GEAR Page 102 CLEAN FLOOR Page 105 LEDSET Page 108 PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 3

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 4

PIXELSCREEN.eu QUICK-GUIDE PLED205Q (FLAT VERSION)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 5

PIXELSCREEN.eu QUICK-GUIDE

50CM 5QFRAME1 (single)

100CM 5QFRAME2 (double)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 6

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 7

PIXELSCREEN.eu QUICK-GUIDE PLED 205Q/QC is one of the most versatile type of led panel ,with a frequent use and high stock surface availability, easy build and quick troubleshooting methods . > Each tile consists of 4 led modules 48x12 pixels with easy access from the back side for removing and replacing ,secured with “stay on “ screws for simple maneuvers. 8 bolts secure the power supply for fast swap in case of malfunction or damage.

> Each panel has two side locks and a guide pin on the side, and one top lock on top for fast assembly via an easy “click and turn” mechanism.

Both types of the PLED 205 (Q and QC) have special characteristics for easy recognition , the PLED 205Q has a flat edge (90°) whereas the PLED 205QC has a slightly angled edge (for curved building) and particular brass-copper knobs on both sides .

It comes in travel dollies, secured with fixing mechanisms (side locks )on both sides ,and protective foam on contact points with the led panels .

Warnings: >The two led types of the P10 Q series (Pled205Q and QC) should never mix on travel dollies and in the same led wall construction (except particular cases). >Travel dollies have one removal side and one fixed side . The fix side is marked with a “do not remove” yellow sticker on top. The two sidewalls have a small removable front protective metal piece that keeps led dolly secure on forklift transportation and are always placed with the protective foam towards the led side. >All led panels have to be tightly secured on the dolly via two rows of side locks on both sides and that keeps led panels in place for minimal movement on transportation and no risk of impact damages on the entire manipulation and transportation process.

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 8

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 9

PIXELSCREEN.eu QUICK-GUIDE

PLED205QC (curve version)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 10

PIXELSCREEN.eu QUICK-GUIDE

M10x20

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 11

PIXELSCREEN.eu QUICK-GUIDE

POWER INPUT

POWER OUTPUT

2x DATA (INPUT = OUTPUT )

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 12

PIXELSCREEN.eu QUICK-GUIDE

REMOVE ONLY 1 SIDE !!!!

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 13

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 14

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 15

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 16

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 17

PIXELSCREEN.eu QUICK-GUIDE PLED203S is a high density led cabinet with a pixel pitch of 3.9mm making it a more “delicate” type of of led panel that requires more attention in handling . >It has a very “easy to click” building system with two hooks on the top that grab two master pins and a turning lever that tightens the module into place and a similar side locking mechanism with a simple turning lever.

>Troubleshooting the PLED 203S is very easy and fast , the power supply can be very fast swapped just by turning two knobs on each side and ,after the swap with a new power supply ,it can be secured in place by reversing the process.

Warnings: Each cabinet requires special attention in handling in the build and break phase due to the protection mechanisms that the tile is provided with.

The tiles come in a protective foam wrap that covers the front side of the led and they are stored in a specially divided flight case.

Handling wise the PLED 203S should only be manipulated from the back side of the panel that has two big handles on each side and the worker should have minimal to zero interference with the front side of the panel. Touching the led side of the panel may result in static electric discharges that might damage the LEDS. After removing the foam protection from the cabinet there is a very important procedural step and that is opening the side blades that protect the edge of the panel during transportation and storage. That can be done by simply pushing the knobs from each side from an outside to a inside position.

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 18

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 19

PIXELSCREEN.eu QUICK-GUIDE

PLED203Q

PLED 203Q comes from the same Q series as the PLED 205Q/QC bringing many similarities and basically having the same framing and locking mechanisms as the PLED 205Q but on a higher pixel density. >The newest member of the Q family brings all the advantages and easy handling methods of the PLED 205Q in a new cabinet with a 3.9 mm pixel pitch , with the difference that it comes in a special designed flight case that can fit 10 panels .

Warnings: Considering the high pixel density and the small led size ,special handling methods have to be taken into consideration. Front handling (on the led side) should be avoided due to static discharge risks and a important attention has to be given especially to the four corners of the led cabinet that are most frequently damaged .

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 20

PIXELSCREEN.eu QUICK-GUIDE

PLED205F

PLED 205F is one heavy duty ,reliable ,led cabinet with a big led surface of 1m² and a very high brightness output. Changing led modules on the cabinet is very fast just by disconnecting imput cable and turning two locks on top and bottom side.

Building and breaking walls with this type of tile requires special tools (inbus size 6 and 8) No special warnings on this tile.

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 21

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 22

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 23

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 24

PIXELSCREEN.eu QUICK-GUIDE PLED208E CURVE PLED206E CURVE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 25

PIXELSCREEN.eu QUICK-GUIDE

PLED208E2 (flat version)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 26

PIXELSCREEN.eu QUICK-GUIDE

PLED208E2C (curve version)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 27

PIXELSCREEN.eu QUICK-GUIDE

PLED208E2KT / E2KB

PLED208EK2T= TOP FLITE (6 panels) always on top

PLED208EK2B= BOTTOM FLITE (12 panels) always on the floor

DRIVE NEVER DOUBLE HIGH WITH FORKLIFT

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 28

PIXELSCREEN.eu QUICK-GUIDE

PLED207D2K / D2BK 10 panels (50x50cm)

12x 50x100cm FRAMES

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 29

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 30

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 31

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 32

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 33

PIXELSCREEN.eu QUICK-GUIDE

PLED205L / PLED205L2

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 34

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 35

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 36

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 37

PIXELSCREEN.eu QUICK-GUIDE

PLED205S/207S (creative panel)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 38

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 39

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 40

PIXELSCREEN.eu QUICK-GUIDE 16

14D

PLED205S is very fragile panel !!!!

ALWAYS WATCH OUT FOR EDGES!!

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 41

PIXELSCREEN.eu QUICK-GUIDE

PLED205ST/207ST (touring panel)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 42

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 43

PIXELSCREEN.eu QUICK-GUIDE

PLED207D/207D2 (floor system)

Silver= PLED207D=2500 nits Black= PLED207D2=4100 nits

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 44

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 45

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 46

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 47

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 48

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 49

PIXELSCREEN.eu QUICK-GUIDE

When reporting damage: Make a detailed note !

WHERE + WHAT Use ‘$’ = Client or other needs to pay.

Use NO ‘$’ = This is damage for Pixelscreen.

Use ‘*’ = To report REPAIR.

Report no damaged LED MODULES on the code of a VIDEOFRAME.

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 50

PIXELSCREEN.eu QUICK-GUIDE

PELICAM2 + JOYSTICK

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 51

PIXELSCREEN.eu QUICK-GUIDE

Powercon CABLES LINK CABLES POC05=20-49cm POC06=50-69cm POC07=70-74cm POC08=75-89cm POC09=90-99cm POC1= 100cm POC15= 150cm POC2 = 200cm POC3 = 300cm POC3D = 300cm doorlink

SCHUKO CABLES POC6 = 6 mtr POC10 = 10-13 mtr POC14 = 14-19 mtr POC20 = 20-24 mtr POC25 = 25-30 mtr PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 52

PIXELSCREEN.eu QUICK-GUIDE

HARTING 16pin LINK CABLES HART5 = 5 mtr HART10 = 10mtr HART15 = 15mtr HART20 = 20mtr HART25 = 25 mtr HART37 = 37 mtr (#2.5) HART75 = 75 mtr (#2.5) HART100 = 100mtr(#2.5) BREAKOUT CABLES POCL= HART16p to POC1.5, 2.5, 3.5… 9.5mtr

POCL10= HART16p to 8x POC 10mtr

POCL5= HART16p to 8x POC 5mtr

POCL10S= HART16p to 8x female schuko 10mtr

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 53

PIXELSCREEN.eu QUICK-GUIDE

NETWORK CABLES LINK CABLES ETH05 = Ethercon 50cm ETH1 = Ethercon 100cm UTP1 = SFTP Cat6 100cm UTP2 = SFTP Cat6 200cm UTP3 = SFTP Cat6 3mtr UTP5 = SFTP Cat6 5mtr UTP10 = SFTP Cat6 10mtr UTP20 = SFTP Cat6 20mtr UTP25 = SFTP Cat6 25mtr REELS (Shill) UTP25H = Reel 25mtr UTP40H = Reel 40mtr UTP40HB = Reel 40mtr klingnet UTP60H = Reel 60-95mtr UTP100 = Reel 95-105mtr UTP100B = Reel 100mtr budget UTP80P = Reel 80mtr+power PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 54

PIXELSCREEN.eu QUICK-GUIDE

POWER CABLES CABLES SUC10 = Shuko 10mtr SUC25 = Shuko 25mtr SUC40 = Shuko 40mtr CE32A10 = Cee32A 10mtr CE32A15 = Cee32A 15mtr CE32A20 = Cee32A 20mtr CE32A25 = Cee32A 25mtr CE63A10 = Cee63A 10mtr CE63A25 = Cee63A 25mtr CE125A10 = Cee125A 10mtr ADAPTOR CE63A125 = Cee63a>Cee125A CE32A63 = Cee32a>Cee63A CE63A32 = Cee63a>Cee32A PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 55

PIXELSCREEN.eu QUICK-GUIDE

VIDEO CABLES LINK CABLES BNC3 = 3 mtr SDI HD HDMI = 1.8mtr HDMI M/M HDMI3 = 3mtr HDMI M/M HDMI5 = 5mtr HDMI M/M HDMI10 = 10mtr HDMI M/M DVI = 1.8mtr DVI M/M DVI3 = 3mtr DVI M/M DVI5 = 5mtr DVI M/M ADAPTOR DVIAH = DVI-D FE/HDMI FE/HDMI MA DVISH = DVI-D FEM / HDMI MA HDMIDVI = DVI-D MA / HDMI MA REELS (Shill) BNC100G15 = 100mtr SDIHD PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 56

PIXELSCREEN.eu QUICK-GUIDE

FIBER REELS (Shill) FIBER150 = Quad opticalCON 150mtr FIBER250 = Quad opticalCON 250mtr FIBER250K = Flite for FIBER250 FIBER200 = 4core SC 200mtr FIBER400 = 4core SC 400mtr

Rack FIBERR = Receiver unit 4x4K + 4xTFT FIBERS = Sender unit 4x4K + 4xTFT FIBERR2 = Receiver unit 2x4K + 2xTFT FIBERS2 = Sender unit 2x4K + 2xTFT

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 57

PIXELSCREEN.eu QUICK-GUIDE

BIG SCREEN SYSTEMS

SBOXD5 5 DOUBLE SENDER 802 CARDS

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 58

PIXELSCREEN.eu QUICK-GUIDE

FIBER RACKS

FIBERS (MATRIX 8x8 + 4 SENDER FIBER 4K / QUAD NEUTRIK

FIBERS (MATRIX 8x8 + 4 SENDER FIBER 4K / QUAD NEUTRIK

FIBERR2

FIBERR (4x 4K FIBER RECEIVER)

FIBERR (4x 4K FIBER RECEIVER)

FIBERS2

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 59

PIXELSCREEN.eu QUICK-GUIDE

DATA DISTRIBUTION HUB LINSN = PELI single HUB LINSN4 = Rack quad HUB LINSN4RO = Roto quad HUB LINSNB = Bag single HUB LINSNDB = Bag duo HUB

LINSNR4P = PELI Quad repeater LINSNR = Single repeater

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 60

PIXELSCREEN.eu QUICK-GUIDE

PSU (Power Supply Unit) UNIT SLOEFS = Ce32A > 6xSchuko SLOEFH = Ce32A > 1xHART16p SLOEFH2 = Ce32A > 1xHART16p+2x Schuko PSU63R = Ce63A > 2xHART16p PSU125R = Ce125A > 6xHART16p PSU400A = 4x Ce125A PSU400AH = 400A > 12xHART16p PSU400AH2 =400A >17xHART16p (12xdual output HART)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 61

PIXELSCREEN.eu QUICK-GUIDE

LINSN SENDER UNIT SBOX802 = Blackbox Sender single card SBOX802P = PELI Sender single card SBOX802DP = PELI Sender dual card SBOXB = BAG Sender single card SBOXB2 = BAG Sender PRO dual card SBOXDB = ROTO Sender dual card PATH4 = RACK Quad Sender card (4K) LS168 = Scaller single card LS168S = Scaller single card (SDI HD) LS1VX = Scaller dual card PRO LS2VX2 = Dual Scaller / quad card LS120 = Scaller single card LS120B = Scaller dual card LS150 = Scaller single card basic model LS170 = Scaller single card

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 62

PIXELSCREEN.eu QUICK-GUIDE

PATH4

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 63

PIXELSCREEN.eu QUICK-GUIDE

LS2VX2

Dual SCALLER/CROPPER/ZOOM with 2x2 SENDING CARDS LINSN including 2x TFT preview monitor

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 64

PIXELSCREEN.eu QUICK-GUIDE

LINSN4RO

EYEPXL7 ROTO Rack with 4 dual LINSN routers

Modulair/Multiformat/ 32 input / 32 output Maximum 64K processing, 128 layhers, 4K inputs !

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 65

PIXELSCREEN.eu QUICK-GUIDE

RIGGING SPAN2 = Strap 25mm 3mtr SPAN4 = Strap 35mm 3mtr SPAN4K = Strap 35mm 1.5mtr SPAN8 = Strap 50mm 8mtr SPAN8O = Strap 50mm 8mtr Ora SLING1 = Flex 1mtr 1 ton SLING1-2 = Flex 1mtr 2 ton SLING3 = Flex 3mtr 1 ton SLING3-2 = Flex 3mtr 2 ton FLEX1 = Steelflex 1mtr 1ton FLEX3 = Steelflex 3mtr 1ton SHAKKEL1 = Schakle 1ton SHAKKEL2 = Schakle 2ton

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 66

PIXELSCREEN.eu QUICK-GUIDE

STEEL80 - black 80cm

C clamp

CE clamp (EYE) CC clamp

G hook

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 67

PIXELSCREEN.eu QUICK-GUIDE

WEIGHTS FLYBARS

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 68

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 69

PIXELSCREEN.eu QUICK-GUIDE

HOW TO BUILD

Everything

starts the day

before you build.

- VIEW ALL TECHNICAL PLANS >>> DROPBOX - CHECK LOADLIST >>> TELEGRAM ‘LOADLISTPDF’ - READ LASTEST PROJECT NOTES >>> TELEGRAM ‘LPV’ - THINK IN ADVANCE HOW TO BUILD >>> TELEGRAM‘PP’ - READ CREWCALL ‘CC’ >>> WORK AS A TEAM! - REPORT ANY DAMAGE IMMEDIATELY >>> TELEGRAM PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 70

PIXELSCREEN.eu QUICK-GUIDE

THE

BUILDING DAY

- ASK IF UNCLEAR - work carefully and LOOK closely at all - keep your printed plans in hand - do time management <<<<<<<< IMPORTANT!!!

- WORK ALWAYS SAFE - Be

a PRO! PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 71

PIXELSCREEN.eu QUICK-GUIDE

ART OF DAMAGECONTROL (learn from the history !!!)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 72

PIXELSCREEN.eu QUICK-GUIDE

EDGES AND CORNERS ARE WEAK !!!

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 73

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 74

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 75

PIXELSCREEN.eu QUICK-GUIDE

CORNER IS EXTREME WEAK!!!

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 76

PIXELSCREEN.eu QUICK-GUIDE

CORNER IS EXTREME WEAK!!!

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 77

PIXELSCREEN.eu QUICK-GUIDE

ETHERCON CONNECTORS CAN EASY BREAK

USE EVERY TIME CABLE PULL RELIEF !!!

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 78

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 79

PIXELSCREEN.eu QUICK-GUIDE ALWAYS ARROWS TO THE TOP DIRECTION!

ROLL REEL NOT LIKE THIS

BUILD LIKE POWERPLAN !

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 80

PIXELSCREEN.eu QUICK-GUIDE

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 81

PIXELSCREEN.eu QUICK-GUIDE

READING PLANS (typical basic setup)

A SENDERBOX or SCALLER

U

LINSN HUB label U1 on plan = 1/

1

4

D

RED COLOR= RETURN LINE (keep unplugged while live building and configuration)

A

LINSN HUB label D1 on plan = 2/

2

4

LED PANEL

LED PANEL

maincable U1 extention 1 order 1

maincable U1 extention 1

LED PANEL

LED PANEL

maincable U1 extention 1

maincable U1 extention 1

order 4

order 3

LED PANEL

LED PANEL

maincable D1 extention 2

maincable D1 extention 2

order 1

order 2

LED PANEL

LED PANEL

maincable D1 extention 2

maincable D1 extention 2

order 4

order 3

order 2

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 82

PIXELSCREEN.eu QUICK-GUIDE (complex setup)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 83

PIXELSCREEN.eu QUICK-GUIDE

(POWERPLAN simple)

PLAN IS ALWAYS LOOKING FROM FRONT SIDE SCREEN !

Maximum power use in Ampere per phase

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 84

PIXELSCREEN.eu QUICK-GUIDE (DATAPLAN simple)

PLAN IS ALWAYS LOOKING FROM FRONT SIDE SCREEN !

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 85

PIXELSCREEN.eu QUICK-GUIDE

(POWERPLAN complex)

POCL=Harting loom to 8x Powercon 1.5, 2.5, 3.5, â&#x20AC;¦ ,9.5 mtr POCL10=Harting loom to 8x Powercon 10mtr BO8=Breakout schuko 8 channels BO8L=Breakout schuko 8 channels + LINK etc...

SOURCES

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 86

PIXELSCREEN.eu QUICK-GUIDE

(DATAPLAN complex) MAX WIDE

U1 HUB

D1 HUB

U/D BORDER

U2 HUB

D2 HUB

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 87

PIXELSCREEN.eu QUICK-GUIDE

DATAPLAN complex

21 reels first input or return line 0 open line / specials links 91 vertical link cables 212 horizontal link cables 303 total link cables

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 88

PIXELSCREEN.eu QUICK-GUIDE

Weight in KG per screen

POWERPLAN

TEST IMAGE (jpg file)

OVERVIEW PLAN

LOCATOR IMAGE (jpg file)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 89

PIXELSCREEN.eu QUICK-GUIDE

POWER REQUIREMENT POWER DETAIL LIST

ADOBE SLIDERS

Resolume Arena Aid

RIGGING DETAIL LIST

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 90

PIXELSCREEN.eu QUICK-GUIDE

TEST ANIMATION (GIF file)

CONFIG SHEET

PRINT VERSION

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 91

PIXELSCREEN.eu QUICK-GUIDE MAPPING Pictures (perfect brightness)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 92

PIXELSCREEN.eu QUICK-GUIDE

PHYSICAL PLANS always in DROPBOX & TELEGRAM PROJECT GROUP

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 93

PIXELSCREEN.eu QUICK-GUIDE

LS168S

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 94

PIXELSCREEN.eu QUICK-GUIDE

LS1VX

INDIGOHR

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 95

PIXELSCREEN.eu QUICK-GUIDE

LOGISTICS P CODES

X CODES

SCAN EVERYWHERE / LOGISTICS : YES DAMAGE REPORT : YES

SCAN EVERYWHERE / LOGISTICS : NO DAMAGE REPORT : YES

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 96

PIXELSCREEN.eu QUICK-GUIDE ICODY APP on IPHONE (QR CODE or BARCODE)

RFID SCANNER (BARCODE or RFID tags)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 97

PIXELSCREEN.eu QUICK-GUIDE Transport pictures (arrival AND depart)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 98

PIXELSCREEN.eu QUICK-GUIDE P-CODES = Allways used for logistic and technical history.

X-CODES = Only for technical history.

“Depart warehouse” (POS 1): Total parts departed at warehouse.

“Arrival production” (POS2): Total parts arrived at production.

“Notes at production” (POS3) : Total parts of damaged hardware.

“Depart production” (POS4) : Total parts scanned ready to depart production, ready to return to warehouse.

“Return at warehouse” (POS5) : Total parts returned to warehouse.

PIX

POS 2

POS 1 POS 3

PIX-Warehouse

POS 5

PIX

POS 4

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 99

PIXELSCREEN.eu QUICK-GUIDE

SEALS—CHECKS—CONTROL

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 100

PIXELSCREEN.eu QUICK-GUIDE RFID Peli including RFID radio scanner

LOAD = Production documents

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 101

PIXELSCREEN.eu QUICK-GUIDE

SAFETY (ALWAYS FIRST!)

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 102

PIXELSCREEN.eu QUICK-GUIDE

GATOR

MAX 20KM/H

Left stick ALWAYS in UNLOCK position

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 103

PIXELSCREEN.eu QUICK-GUIDE

MINIMAL GEAR SET for ALL V (Videotechs/Stagehands/Crew workers)

1 on 2 person

1 on 3 person

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 104

PIXELSCREEN.eu QUICK-GUIDE

MINIMAL GEAR SET for CC (Crew Chief) NR 8 + 6

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 105

PIXELSCREEN.eu QUICK-GUIDE A.

MINIMAL GEAR SET for SCC (Super Crew Chief) ALL GEAR of CC and next: LABEL PRINTER (battery powered)

Mobile printer (battery powered+WIFI)

LAPTOP minimal Core i7 16Giga

LASER DISTANCE METER

HEAVY DUTY 10000mA Powerbank

3G/4G Mobile Wifi routerâ&#x20AC;&#x201D;battery powered

4K HDMI/DVI/SDI-HD Video generator

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 106

PIXELSCREEN.eu QUICK-GUIDE

CLEAN FLOOR NEVER HARDWARE ON THE GROUND

NEVER !!!!

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 107

PIXELSCREEN.eu QUICK-GUIDE

RCG FILES

PLED225

PLED208E

PLED216/216R/216M

PLED206E

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 108

PIXELSCREEN.eu QUICK-GUIDE

THANK YOU! Iphone / Android / Win Phone Install Telegram APP on your smartphone and Windows / macOS / Mac / Linux Send a private telegram message ‘HELLO’ to user ‘@PIX_BOT’ and answer some questions.

Press ‘CONFIRM’ button.

Then you are a real Pixelscreen team member, you will receive future updates of all the latest products.

PIXELSCREEN guide for beginners : how to quickly and safely build a LED screen.

Page 109

PIXELSCREEN.eu

MSPLS - Minimal Steps Plan LEDSET by Linsn.

The next steps are the minimal steps to do for setup a videosystem by LedSet v2.3.

It isn’t possible anymore to setup the latest videopanels of PIXELSCREEN with Ledstudio versions!!

Follow all steps in the correct order, don’t try to do this in a wrong order.

1. Install all video panels and do all physical connections of Data– and Power cables, LINSN HUB, PSU’s,…

(BACK UP/HOT RETURN DATA LINES—DISCONNECTED TO LINSN HUB!)

PLAN IS ALWAYS LOOKING FROM FRONT SIDE SCREEN !

Follow all printed plans of cable preparation.

2. Install LEDLAP (All laptops of Pixelscreen are named LEDLAP, all necesary software is installed) to Senderbox or Scaller via USB. (listen that you hear Windows confirm by a sound tune when USB is good connected).

3. Connect LEDLAP via DVI or HDMI cable to senderbox or processor.

4. Setup Windows for second display port to the right resolution (1920x1080/…) and choice EXTENDED SCREEN

5. Use Faststone GIF viewer to show TESTPICTURE.JPG or TESTANIMATION.GIF

on second display port.

(PROJECT REFERENCE (CLIENT) (test picture).jpg or PROJECT REFERENCE (CLIENT) (animation).gif in ZIP file.)

Linsn LED setup

Page 110

PIXELSCREEN.eu 6. Check all panels at backside for DATA LED is flashing !

If NOT, go to step 1.

(skip step 6, if you do LIVE building. When LIVE building you go through the whole list many times, every time in the right order.)

7.

Startup LedSet (if LedSet was already running, close en re-start.)

If ‘Unknown’ after clicking ‘Detect’ button and Serial port State is ‘Connected’.

Change senderbox or scaller/senderbox.

This must be a malfunction.

If ‘Not Connected’ go to step 2.

Linsn LED setup

Page 111

PIXELSCREEN.eu 8.

50 (19.06%)

Click Brightness

‘Default’ -> ‘50’ (19%) -> Send to screen -> Save to screen -> Exit It is important to do this, you never know from where the panels came before this rental.

9.

Click Screen

This number can be found on DATA PLAN plan. X=xxxx Take care, you select the right frequency, 50 or 60Hz

Configuration ‘Default’ -> Display Mode (1920x1080 for example) -> Set Width -> Max Width (example 1460) -> Save to sender It is important to do this, you never know from where the senderbox came before this rental.

Linsn LED setup

Page 112

PIXELSCREEN.eu 10. tab

Take care, you select the right frequency, 50 or 60Hz Never ‘AUTO’.

Load from files -> c:\Dropbox\WORK LEDLAP \PIXELSCREEN\RCG \Config files PLED203Q\*.RCG Select the right RCG file !

Pixelscreen has many version of each panel.

Selecting the wrong RCG file can cause unrepairable DAMAGE. If you don’t want to take any risc, make a picture of this page and send/telegram to us.

Pixelscreen do directly a confirmation of correctness.

-> Select correct Hz (change AUTO to 50 or 60) -> Send to receiver Check before you press CONFIRM, that all panels has the same display.

All panels show now the same information of LEDLAP display port 2 at top left corner. If not, go to step 1.

-> Save to receiver (never do Save if the above check is incorrect displayed on all panels!)

Step 10 is only possible when 1 sort of video panel is connected at the time with the senderbox.

Linsn LED setup

Page 113

PIXELSCREEN.eu

11. tab Never use this page !

12. tab Update displaty QTY to ‘1’ -> press Update display QTY -> Select correct Horizontal card number -> Select correct Vertical card number -> Main cable = (1 No sender U cable 1U = first sendercard, U port.)

(2 No sender D cable 2D = second sendercard, D port) Extension = Port number on the LINSN HUB station (1 to 9) Order No. = Panel order number on the cable. (first panel =1 , second panel =2, …) Every cable start again with 1.

Width = Total real pixels of 1 panel wide.

Height = Total real pixels of 1 panel high.

ALL THIS INFORMATION, YOU CAN READ ON THE DATAPLAN . (see ealier in this manual) Pixelscreen workers, configer all display screens on 1 master Display! We never use more as 1 Display.

This is more stable, faster and less problems in the future.

Linsn LED setup

Page 114

PIXELSCREEN.eu (continue step 12) -> Save to file (for later use) -> Send to receiver if all pictures look goodâ&#x20AC;&#x201D;do save -> Save to receiver

USEFULL TRICK: Click

to get an graphical overview of your datacable plan configuration.

Linsn LED setup

Page 115

PIXELSCREEN.eu 13.

Go back to Brightness Indoor panels Outdoor panels Semi outdoor panels*

Indoor use

Outdoor use

100%

100%

30-60%

95%

100%

100%

Select the right level of brightness just before showtime.

-> Save to screen -> Exit *(Semi outdoor panels are rainproof panels with less as 5000nits brightness in the catalog listed.)

14.

Make picture of testimage.jpg and send on telegram projectgroup.

After PixBot recognise the QR code, you receive more specialty necessary setup information (project related).

15. Close LedSet software (close window).

16. Swap master data input lines, and test retour/hot backup data lines for 100% functionality.

Linsn LED setup

Page 116

PIXELSCREEN.eu Exceptions.

Step 9: If the data plan is based on column mapping (verticals columns), and not the normal row mapping (horizontal banners) -> un flag Set Width, and Width=0 Step 12: If 2 or more sorts of videopanels are connected to the same senderbox. Use 1 display per sort videopanel.

Step 14: If QR codes are too small, make more pictures.

Linsn LED setup

Page 117

PIXELSCREEN.eu

Telegram& Pixbot Telegram communication: Setup and Use of TELEGRAM (secure messenger).

Chat with PIXBOT about a project.

Chat with PIXBOT about your personal work planning.

Chat with PIXBOT FAQ (Frequently Asked Questions) Software scanners: Setup and Use of ICODY (iOS iPhone) Setup and Use of Wifi Barcode Scanner (Android smartphone) Nordic RFID Scanner (Radio-frequency identification)

telegram & pixbot communication

Page 118

PIXELSCREEN.eu

TELEGRAM & PIXBOT

telegram & pixbot communication

Page 119

PIXELSCREEN.eu

Step into the World of PIXELSCREEN.eu WHY TO DO THIS AS A DRY HIRE CLIENT? To obtain the P PARTNER PRICE —get 10% extra discount.

You need to scan all goods on arrival and departure by App (Icody) or Nordic RFID scanner.

Fully completing a COUNTING list. (green document) All material orderly sorting in FLITECASES. Perfect reporting all damage and defective material.

WHY TO DO THIS AS A FREE LANCER / LED TECHNICIAN / PROJECT LEADER? This is the only way to work fast—do your job right—and make less mistakes.

Good communication—always the latest information update—No waiting times—Plan your agenda, your workload.

WHY TO DO THIS AS A SALES PERSON / PURCHASER ?

This is the only way to work fast—make the best deal—and make less mistakes.

Good communication—always the latest information update—No waiting times. All projects ordered in a separate project chatgroup.

By communicating over Telegram we make all projects clear, correct material blocking, talk fast about price requests, deal negotiation, order changes, upgrades, downgrades, technical plans/drawings, requirements , …

MAKE EVERYTHING FAST— CLEAR FOR BOTH PARTIES.

telegram & pixbot communication

Page 120

PIXELSCREEN.eu

TELEGRAM WELCOME HALL FIRST STEP: Add user @PIXELSCREEN or make a new contact PIXELSCREEN +32 473 69 99 99

Say “hello” From this moment an operator pick you up.

He gives you access to all the necessary telegram groups.

@Pix_Bot is an artificial chat bot.

Pixelscreen has an interface with the Telegram servers to communicate all information you need. Telegram combines security, reliability and speed on any network.

ALL IS FREE!

telegram & pixbot communication

Page 121

PIXELSCREEN.eu

TELEGRAM SETUP Install TELEGRAM on your Iphone/Android AND Windows PC or MAC computer!!! This app is FREE, 0â&#x201A;Ź This messenger can be installed on smartphone and computer at the same time, with the same account. All information is continuous synchronized, encrypted, fast and cloud server based.

We share all documents, CAD files, PDFâ&#x20AC;&#x2122;s, Video and Ledstudio files over Telegram. You can talk to Pixbot, a virtual telegram user that is live linked to the Pixelscreen servers.

Surf www.telegram.org of go to your smartphone appstore.

telegram & pixbot communication

Page 122

PIXELSCREEN.eu

TELEGRAM GROUPS There are some sorts of chat groups: 20160305 DLDK (TSUP) This is a project group. All information about one video production. @PIX_BOT (Pixbot) is always a chat member.

PLANNING YOUR NAME This is a crew planning chat group. All personal information about my work in the past and in the future. @PIX_BOT (Pixbot) is always a chat member.

PIX ACADEMY [READ ONLY!!!!]

This is a general information channel. Only for reading some updates.

PIX TRANSPORT INTERN This is all information about transport material, arrival trailers, etcâ&#x20AC;¦ AND also general project planning.

telegram & pixbot communication

Page 123

PIXELSCREEN.eu

TELEGRAM—PROJECT CHATGROUP 20160325 PAASP16 (PAASPOP) This is an example of a project chat group.

20160325 = 25 march 2016, is first showday.

PAASP16 = internal reference to the project name, PAAS POP 2016 FESTIVAL (PAASPOP) = client code COMMANDO’s (most important/most used): HELP This give you an overview of all commando’s.

LS Ask pixbot to give an overview of all scans.

LIVE Ask pixbot to give an overview of all scans and refresh information every minute for 30 min (same as LS).

OS Ask pixbot to give general information about the project.

LOADLIST Ask pixbot to give a detailed & latest LOADLIST. LOADLISTPDF Ask pixbot to give a detailed & latest printed LOADLIST.PDF. PIVOT or PV Ask pixbot to give a detailed barcode scanning list.

CC Ask pixbot to give a detailed crew planning overview.

MAPPING Ask pixbot to give all videomapping files.

DATAPLAN Ask pixbot to give DATA CABLING plan.

POWERPLAN Ask pixbot to give POWER CABLING plan.

POWERREQ Ask pixbot to give POWER REQUIREMENT.

telegram & pixbot communication

Page 124

PIXELSCREEN.eu

TELEGRAM COMMANDO : LS LS = Loadlist Status (compact status of all barcodes scanning)

P-CODES = Allways used for logistic and technical history.

X-CODES = Only for technical history.

“Depart warehouse” (POS 1): Total parts departed at warehouse.

“Arrival production” (POS2): Total parts arrived at production.

“Notes at production” (POS3) : Total parts of damaged hardware.

“Depart production” (POS4) : Total parts scanned ready to depart production, ready to return to warehouse.

“Return at warehouse” (POS5) : Total parts returned to warehouse.

PIX

POS 2

POS 1 POS 3

PIX-Warehouse

POS 5

PIX

POS 4

telegram & pixbot communication

Page 125

PIXELSCREEN.eu

TELEGRAM COMMANDO : OS / PS OS = Order Status (status of a project)

PS = Pixbot Status (status of the server)

telegram & pixbot communication

Page 126

PIXELSCREEN.eu

TELEGRAM COMMANDO : LOADLIST LOADLIST : Ask Pixbot a detailed loadlist of the project.

CTRL = Qty of not yet returned parts.

RET. = Qty of returned parts.

BARC = Total scans at departing at warehouse.

PICK = Qty departed parts.

ORD = Qty ordered parts.

S = Handling method (“B”=P CODE, “-” = Manual count) ART.CODE = Part code ART.DESCRIPTION = Part description REMARK = Warehouse remarks.

telegram & pixbot communication

Page 127

PIXELSCREEN.eu

TELEGRAM COMMANDO : PIVOT / ML PIVOT : Ask Pixbot a detailed scanning list of the project.

1 = Departed warehouse 2 = Arrival production 3 = While production 4 = Ready to depart production 5 = Arrival warehouse ML : Ask Pixbot a detailed scanning list of the project, but only the missing parts at LOAD-OUT.

telegram & pixbot communication

Page 128

PIXELSCREEN.eu

TELEGRAM COMMANDO : CC CC : Ask Pixbot a detailed crew and transport planning of project.

telegram & pixbot communication

Page 129

PIXELSCREEN.eu

TELEGRAM COMMANDO : COUNTLIST / CL COUNTLIST : Ask Pixbot a detailed countlist of the project. >TEXT version (=best idea to view on screen) CL : Ask Pixbot a detailed countlist of the project. >PDF version. (=best idea to print !)

A countlist is a list where ONLY all MANUAL COUNTED parts are listed (everything without a barcode).

CLM : Ask Pixbot a detailed countlist of the project, SPLIT OUT per area. >PDF version. (=best idea to print !)

TXT version

CTRL = Number of parts still not returned to warehouse [ ] = Total counted parts HULP VAK = Temporary count numbers.

PDF version

telegram & pixbot communication

Page 130

PIXELSCREEN.eu

TELEGRAM COMMANDO : POWERPLAN / DATAPLAN POWERPLAN : Ask Pixbot a graphical power cabling plan.

DATAPLAN : Ask Pixbot a graphical power cabling plan.

telegram & pixbot communication

Page 131

PIXELSCREEN.eu

TELEGRAM COMMANDO : MAPPING MAPPING : Ask Pixbot a detailed video mapping and all files of 1 project.

OVERVIEW FILES PROJECT REFERENCE (CLIENT) (overview).jpg = General overview of all displays (visual version).

PROJECT REFERENCE (CLIENT) (overview).txt = General overview of all displays (text version).

PROJECT REFERENCE (CLIENT) (test picture).jpg = General test picture in requested source format.

PROJECT REFERENCE (CLIENT) (test image).jpg = Preview of final result by picture of Angelina Jolie, pixelcorrect 1:1.

PROJECT REFERENCE (CLIENT) (rigging).prn = General overview of all weights and rigging requirements.

PROJECT REFERENCE (CLIENT) (animation).gif = Animated GIF picture (testpicture/color test/image test).

PROJECT REFERENCE (CLIENT) (dataplan).jpg = Data cable plan of all displays.

PROJECT REFERENCE (CLIENT) (locatorplan).jpg = Cabinet locator plan with numbering.

PROJECT REFERENCE (CLIENT) (ledstudio aid).prn = Sheet to help setup LEDSTUDIO software.

PROJECT REFERENCE (CLIENT) (power detail).txt = Power calculation overview of all cables (Amps).

PROJECT REFERENCE (CLIENT) (powerplan).jpg = Power distribution cable plan of all displays.

PROJECT REFERENCE (CLIENT) (labels).prn = List of all cable labels â&#x20AC;&#x201C; pre printed.

PROJECT REFERENCE (CLIENT) (guides).jsx = Import directly the snapping guides to Photoshop/After Effects/Premiere from the mapping. (before you import, be sure, change RULER UNITS to "pixels", FILE -> SCRIPTS -> BROWSE) PROJECT REFERENCE (CLIENT) (resolume).xml = Import directly the slides mapping into Resolume Arena5 in your mediaserver.

(OUTPUT -> ADVANCED -> PRESET -> LOAD -> select XML file)

PROJECT REFERENCE (CLIENT).DAT = Data file of datacabling setup.

PROJECT REFERENCE (CLIENT).POW = Data file of powercabling setup.

PROJECT REFERENCE (CLIENT).txt = Short data file of general setup.

telegram & pixbot communication

Page 132

PIXELSCREEN.eu

TELEGRAM COMMANDO : ZIP / LOGIN ZIP : Ask Pixbot to make 1 ZIP file of all technical files related to 1 project, all areas, ready for download.

LOGIN PCODE : Ask Pixbot to send all Windows login information for 1 laptop.

A laptop with Ledstudio installed is named LEDLAP.

telegram & pixbot communication

Page 133

PIXELSCREEN.eu

TELEGRAM DAMAGE REPORTING : P/X CODES Reporting or Checking : damages, missings, abnormality, repairs…

Articles with :Type P– or X-CODE Examples: P15H009 DVI CABLES MISSING Report at part P15H009 that “DVI CABLES ARE MISSING” RED STATUS P15H009 Report NOTHING, ask Pixbot about last status.

P15H009 * NEW CABLE Report at part P15H009 that “NEW CABLE is installed” special characters “*” = repaired, works perfect, found, … = GREEN STATUS “$” = cost for client or other supplier = GREEN STATUS LOG P15H009 Ask Pixbot to give overview of last 10 notes/status changes of this part.

PS. Never use the character “,” in any commando or note line.

telegram & pixbot communication

Page 134

PIXELSCREEN.eu

TELEGRAM DAMAGE REPORTING : NO BARCODE Reporting or Checking : damages, missings, abnormality, repairs…

Articles with :No Barcode First step is requesting a NEW Barcode number from server NEWXCODE Write this new XCODE with Gaffa on the broken part.

Second step is registrating the remark (same as now with P/X Code) P15H009 HART25 CONNECTOR MISSING Report at part P15H009 that “HART25 CONNECTOR MISSING” RED STATUS

P15H009 Report NOTHING, ask Pixbot about last status.

PS. Never use the character “,” in any commando or note line.

telegram & pixbot communication

Page 135

PIXELSCREEN.eu

TELEGRAM SEARCHING SYSTEMS : GPS / LOC / PIC / BAG All technics to find some parts.

Type Pâ&#x20AC;&#x201C; or X-CODE

Examples: GPS P15H009 Ask Pixbot last know GPS location via code.

LOC PSU125R Ask Pixbot all status and gps locations of 1 part at project.

PIC P15H009 Ask the operator for the latest know picture of P15H009.

BAG P15H009 Ask the operator for the last know BAG (FLITE/PELI/DOLLY) where P15H009 was packed/loaded in.

telegram & pixbot communication

Page 136

PIXELSCREEN.eu

TELEGRAM “PLANNING YOUR NAME” This chatgroup is a small chatgroup, PERSONAL USE, with ONLY YOU, the CREWPLANNERs and PIXBOT joined together.

Use this group to plan your work, your holidays, your availability.

VERY USEFULL COMMANDO’s: O Ask pixbot a PDF overview of ALL MY PLANNING OC Ask pixbot a PDF overview of ALL PAYMENTS M M02

Ask pixbot the actual planning months.

Ask pixbot an overview of the second month of the year (Februari) 071116 Say Pixbot to switch your availability on that day 071116 = 7 November 2016 Switch FREE FOR WORK or OCCUPIED FOR WORK 071116 HOLIDAY (date + text) Say Pixbot that on 7 November 2016, I want a day off.

071116 DEL Remove your text on day 7 November 2016.

telegram & pixbot communication

Page 137

PIXELSCREEN.eu

TELEGRAM “PLANNING YOUR NAME” - Examples Examples: M03 Ask pixbot overview of my work of the month MARCH

Examples: Reporting 2 days holiday in IBIZA

telegram & pixbot communication

Page 138

PIXELSCREEN.eu

TELEGRAM PIXBOT F.A.Q. DATABASE Our chat robot Pixbot is more and more artificial with time.

If you donâ&#x20AC;&#x2122;t know, just ask it by chatting !!!

We are working hard to expand the database of frequent asked questions. Pixbot uses all information we store in the server about logistic, sales, manuals, settings, mappings, configuration files, changelogs, gps tracking, warehousing, damage reports, hundreds of thousands of photos, â&#x20AC;Ś

telegram & pixbot communication

Page 139

PIXELSCREEN.eu

TELEGRAM “PIX TRANSPORT INTERN” Pixbot post daily an Project General Overview PDF.

CPL = First stage—picking all parts in warehouse.

LOADLIST = Second stage—warehouse is checking/scanning/picturing/counting all goods.

CXX = Warehouse software do final checks by comparing scans, RFID tags, weights, photos (object recognition), history, volumes, lists.

LOAD = Red folder with all production files printed on paper.

RETURN-LOADLIST = Last stage—warehouse is checking return.

CXZ = Damage report of 1 project.

COUNTLIST = Return countlist of all parts without barcode/rfid.

Notes Agreement formula PROD = PRODUCTION (Pixelscreen offers you full service installation. This includes crew, transportation, maximum monitoring while show time, full setup LED software and processors, etc…)

DRY = DRY HIRE (Pixelscreen offers you only the material including spare units and all necessary information, computer & software to do installation by yourself. We prepare also a customized riggingplot, test-picture, test-hires image, animation clip, data- & power cabling plan to build your setup, on request.)

DRY-1 = DRY HIRE ASSIST (This is the same as DRY HIRE but we offer 1 tech at building up phase to assist you.)

SALE = We sell you this material.

BOXM = We do only box moving, no warranty (subrental).

MIX = Any other combination of above Transport PIX= Pixelscreen arrange transportation at load in & load out.

CLIENT= Client arrange transportation.

telegram & pixbot communication

Page 140

QUICK PIXELSCREEN.eu CHART TELEGRAM Commando .

CC CCSPAM CHECK IN CHECK OUT CL CLM COUNTLIST CREWCALL CUM CUMLIST DATAPLAN FS GPS P99H999 GUIDEBEGINNER HELP HULP LAST30 LAST30RFID LAST5 LAST5RFID LIVE LIVESTOP LOADLIST LOADLISTPDF LOC PSU125R LOCATORPLAN LOG P99H999 LOGIN P99H999 LPS LPV

Action Ping Pixbot - check of alive Request CREW-TRANS call sheet.

Send CREW-TRANS to all workers (administrator) Start workday.

End workday.

Request COUNTLIST sheet in PDF - 1 master list.

Request COUNTLIST sheet in PDF - 1 list per area.

Request COUNTLIST sheet in TXT. Request CREW-TRANS call sheet.

Request compact cummulative scanned codes list.

Request compact cummulative scanned codes list.

Request dataplan files.

Request overview fullsize scanned codes.

Request GPS location.

Request beginners manuals.

Help in English.

Help in Dutch.

Show last 30 scans compact view.

Show last 30 RFID scans compact view.

Show last 5 scans.

Show last 5 RFID scans.

Startup live overview shortlist scanned codes.

Stop LIVE Request actual loadlist information.

Request LOADLIST PDF with confirmed information.

Request overview article.

Request lovator plan files.

Request last information.

Request login password.

Send preproduction PDF to client.

View preproduction PDF.

LS

Request overview shortlist scanned codes.

LSZ M MANUAL P99H999 MAPPING MISSINGLIST ML NEWCODE O OA OC OS P99H999 * POS2 P99H999 NOTE PIC P99H999 PIVOT POWERPLAN POWERREQ PP PRODPLAN PS PV QG RCG PLED203S SYNC TRAILERS VIDEOPLAN VIDEOPROD VOK VOL XTOKEN ZIP

Request overview shortlist P codes only.

Planning -> give me active months * Request manual.

Request mapping files.

Request overview missed codes.

Request overview missed codes.

Request a NEW X-Code.

Request PDF overview personal planning (future) * Request PDF overview personal planning (history). * Request PDF overview financial cash flow. * Request project status.

Move code to new position manual.

Register damage/malfunction.

Request last picture.

Request overview scanned codes.

Request powerplan files.

Request client custom production test file.

Ask link for preproduction.

Request client custom production test file.

Pixbot server status.

Request overview scanned codes.

Give me a quick quide help file.

Request RCG info video panel.

Sync crewplanning (administrator) Request ALL trailers info (administrator) Request all video test files.

Request client custom production test file.

Confirm checkup loadlist.

Give info about transport.

Request TOKEN Request ZIP file with ALL technical files zipped. * = works only in PLANNING groups.

telegram & pixbot communication

Page 141

PIXELSCREEN.eu

telegram & pixbot communication

Page 142

PIXELSCREEN.eu

iOS iPhone : ICODY setup Install ICODY from Apple App Store. This app exist only on Iphone and Ipad and cost 10â&#x201A;¬.

ICODY is an smartphone professional BARCODE/QR CODE scanner : LIVE LINKED to the Pixelscreen servers (ONLINE MODE) OR with the possible to use WITHOUT INTERNET connection (OFFLINE MODE)

telegram & pixbot communication

Page 143

PIXELSCREEN.eu

ICODY SETTINGS Go to setting and do install like on pictures. https://zapier.com/hooks/catch/bq31zo/

telegram & pixbot communication

Page 144

PIXELSCREEN.eu

ICODY ONLINE MODE Press SCAN and SCAN—THAT’s ALL

After each successfull scan, you feel your smartphone vibrating.

telegram & pixbot communication

Page 145

PIXELSCREEN.eu

ICODY OFFLINE MODE Do the scan method as ONLINE, after scanning all. Wait till you have a good internet connection with your smartphone (Dataconnection or Wifi)

Step 2: CLICK HERE

Step 3: CLICK all codes you want to send to the server.

Step 4: CLICK on “Send”

Step 1: CLICK HERE

telegram & pixbot communication

Page 146

PIXELSCREEN.eu

Mobile RFID scanOpen the antenne like on the picture.

Start scanning by pushing

.

After scanning all—touch “TRANSFER” on the screen and follow next instructions on the screen.

ATTENTION: If you see “0 / F=0” on the screen, all codes are send to the server.

This 2 numbers are indicating the buffer memory of the scanner!

telegram & pixbot communication

Page 147

PIXELSCREEN.eu

telegram & pixbot communication

Page 148

PIXELSCREEN.eu

Android :WiFi Barcode Scanner setup Install WiFi Barcode Scanner from dacalleg Play Store. This app exist only on Android and cost 0.99â&#x201A;¬.

This is an industrial smartphone professional BARCODE/QR CODE scanner : LIVE LINKED to the Pixelscreen servers (ONLINE MODE).

telegram & pixbot communication

Page 149

PIXELSCREEN.eu Do the next setup steps…

Remove Default Chain “Barcode Lookup” swipe right -> delete

Remove Ads—buy app 0.99€

1

telegram & pixbot communication

Page 150

PIXELSCREEN.eu Follow all steps 1 2 3 …

1

4 5

2

3

Click right-top add parameter “USER” data “Your Name” then click + make a Chain “pixelscreen” then EDIT

telegram & pixbot communication

Page 151

PIXELSCREEN.eu Edit Chain “PIXELSCREEN” first step : Barcode Scanner second step : HTTP request

1 2

This looks GOOD !

https://hooks.zapier.com/hooks/catch/648917/rw2z69/

telegram & pixbot communication

Page 152

PIXELSCREEN.eu

ALLOW Camera access

ALLOW access to location GPS

First time, you see “Waiting for location”

Use LOOP for startup SCANNING BARCODES

READY !

Test your Android Scanner

telegram & pixbot communication

Page 153

PIXELSCREEN.eu

PP PPâ&#x20AC;&#x201D;Preproduction

Page 154

PIXELSCREEN.eu

PP—Preproduction online-form Telegram commando: PP LPV LPS

Request PP weblink.

Request last official PDF version and client communication detail.

Send last PDF version to client.

Very Important & Very Easy PP—Preproduction

Page 155

PIXELSCREEN.eu

PPâ&#x20AC;&#x201D;Preproduction

Page 156

PIXELSCREEN.eu

PPâ&#x20AC;&#x201D;Preproduction

Page 157

PIXELSCREEN.eu

PPâ&#x20AC;&#x201D;Preproduction

Page 158

PIXELSCREEN.eu

PPâ&#x20AC;&#x201D;Preproduction

Page 159

PIXELSCREEN.eu

This is a time clock.

Every second preparation is won in 1 minute tomorrow!

PPâ&#x20AC;&#x201D;Preproduction

Page 160

PIXELSCREEN.eu

THANK YOU

PPâ&#x20AC;&#x201D;Preproduction

Page 161

PIXELSCREEN.eu

PPâ&#x20AC;&#x201D;Preproduction

Page 162

PIXELSCREEN.eu

Time winner.

To win a lot of time on the production floor.

To win a lot of mistakes.

To double check all parameters in advance.

ALWAYS USE AN USB STICK TO ARCHIVE ALL FILES.

PIXELSCREEN ask to all CC (Crew Chiefs) or clients to prepare LED Studio in advance.

This is the most safe and easy way to switch from computer to computer.

1. Copy the WHOLE LEDSTUDIO folder to a new folder.

You can start LEDStudio directly from the USB stick.

The backup of all ledstudio files is archived on the cloud by Telegram.

One folder per senderbox or area.

Start up ledstudio.exe in that new folder directly.

2. Make a ZIP file of the whole folder LED Studio folder.

3. Send this ZIP file to Telegram Project Chatgroup.

Pixbot DOUBLE CHECK all parameters for you and give you any feedback over Telegram.

PPâ&#x20AC;&#x201D;Preproduction

Page 163

PIXELSCREEN.eu QUICK-GUIDE DIS3BUTION NV â&#x20AC;&#x2DC;s Herenweg 5-2 1860 MEISE BELGIUM BTW/TVA BE 0449743666 Tel > +32 473 699999 Telegram > @pixelscreen Email > info@pixelscreen.eu Facebook > https://www.facebook.com/Pixelscreenbe/ All information is subject to verification Pixelscreen is a EURO copyrighted brand.

Orders / Prices > http://action.pixelscreen.eu New client > http://newclient.pixelscreen.eu Jobs / Work > http://job.pixelscreen.eu Videoconference > http://hotroom.pixelscreen.eu

Last page