SAFETY INSTRUCTIONS Please read and follow all safety instructions carefully before installation and use. Failure to follow these instructions may result in electric shock, fire, injury, product damage, or water leakage.
General Safety WARNING ·This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. ·Children should be supervised to ensure that they do not play with the appliance. ·Do not allow children to play with packaging materials. ·Do not disassemble, repair, or modify the product without authorization.
Electrical Safety WARNING · This product is a Class I electrical appliance and must be connected to a properly grounded electrical system. · Do not insert or remove the power plug with wet hands. · The power supply must comply with applicable local electrical regulations. · Do not use the product if the power supply cord or plug is damaged. The power cord must be replaced by the manufacturer, its service agent, or a qualified person to avoid any hazard. · Do not install this electrical appliance in locations where it may be exposed to direct water spray, excessive moisture, or high temperatures, such as near showers or heat sources. · Do not turn the product upside down during installation or transportation. · The Portable Residual Current Device (PRCD), if supplied with the power supply cord, must be securely installed and kept accessible.
Water Safety WARNING · Connect the product only to a potable water supply. · Ensure that the water supply pressure is within the specified operating range of the product. · Where required by local regulations, suitable backflow prevention protection shall be provided. · Do not twist, kink, crush, or excessively bend the flexible water inlet hose. · Ensure that all water connections are properly tightened before use. · Check all water connections regularly for leakage. · Do not use the product if water leakage is detected. Shut off the water supply immediately and rectify the problem before use.
NOTE: Australia & New Zealand ·Installation must be carried out by a licensed plumber. Any electrical work, if required, must be performed by a licensed electrician in accordance with applicable local regulations. ·Installation must comply with the National Construction Code (NCC) Volume Three, AS/NZS 3500.2, and the Plumbing Code of Australia (PCA).
*All installations must comply with local regulations.
*Disclaimer We will not be liable for any damage, injury, or loss resulting from failure to comply with the safety instructions provided in this manual.
-1-
TECHNICAL SPECIFICATION S�����������
Wash
D�ing/ Warm Air Heated Seat Hygiene
Rear Wash
●
Front Wash
●
Oscillating Wash
●
Adjustable Water Temperature
4 Levels
Adjustable Water Pressure
4 Levels
Adjustable nozzle Position
4 Levels
Air D�ing
●
Adjustable D�er Temperature
4 Levels
Heated Seat
●
Adjustable Seat Temperature
4 Levels
Nozzle Automatic Cleaning
●
Nozzle Manual Cleaning
●
Display Screen
●
Remote Control
●
Night Light
●
Open Lid/Seat Automatically
● � � on unit with � � �ex hose
Water Supply Connector
AC 220 - 240V, 50/60HZ
Rated Voltage
Wash Device
D� Device
Heated Seat
Remote Control
Power
1200W
Length of Powder Cord
1.2m
Water Supply Pressure
150~650KPA (1.5~6.5 Bar)
Water Supply Temperature
4~35°C
Ambient Temperature
5~40°C
Protection Degree
IPX4
Flow Rate
650 ml/min
Water Temperature
Room temperature ～ 40°C
Wash Cycle Time
95 seconds
Heating Mode
Instant heating
Water Tank Volume & Water Tank Heater Power
4.5L, 1200W
Safety Device
Thermal Cuto Fuses\Liquid
Speed Of Air
≥4m/s
D�er Power
225W
D� Cycle Time
2 Minutes
Warm Air Temperature
Room temperature ～ 55°C
Safety Device
Thermal Cuto Fuses\Thermostat
Heated Power
40W
Seat Temperature
Room temperature ～ 40°C
Safety Device
Thermal Cuto Fuses\Thermostat
Frequency Range
2400-2520MHz
Maximum RF Output Power
-10dBm
Type of Batteries
AAA d� batte�
Number of batteries
Two Pieces IPX4
Protection Degree Other Safety Device
Residual Current Devices
1. Only applicable to high version and top version. 2. The power consumption depends on the inlet water temperature, environment temperature, setting temperature.
-2-
TOILET DIMENSIONS Unit: mm
700
∅100 30
180
120 60
90
55 50~220 400
Ov����w
∅15
Lid
Display Screen
Detection Sensor
D�er Night Light
LED Light
Rear Wash
Side knob
Front Wash
Ceramic bowl
-3-
CHECKING LIST After unboxing, please check the table below to ensure all parts are included. If any parts are missing, please contact customer service.
Remote Control
Aroma Tablet
User Manual
Batte� Box
The following accessories are included with TOP version only.
Foam Shield Tablet
Foam Mix Bottle
-4-
FUNCTION INSTRUCTION Hygiene Features Front Wash
Provides a soft water spray for feminine hygiene with an automatic 95-second washing cycle.
Rear Wash
Provides a gentle water stream for posterior cleansing with an automatic 95-second washing cycle.
Oscillating Wash
Moves the spray nozzle back and forth during washing to provide wider cleaning coverage. Available during both Front Wash and Rear Wash.
Nozzle Self-Cleaning
Automatically rinses the spray nozzle before and after each washing cycle. Manual nozzle self-cleaning runs for approximately 60 seconds.
UV Sterilization (if applicable)
Automatically activates when the lid is closed to help maintain toilet hygiene.
Fragrance Function (if applicable)
A fragrance cartridge releases a pleasant scent naturally to help keep the toilet area fresh.
Comfo
Features
Drying
Provides air drying after washing with an automatic 2-minute drying cycle.
Water Temp Adjustment
Provides four levels of water temp adjustment: room temp, 34°C, 37°C, 40°C.
Seat Temp Adjustment
Provides four levels of seat temp adjustment: room temp, 34°C, 37°C, 40°C.
Dryer Temp Adjustment
Provides four levels of air drying temp adjustment: room temp, 35°C, 45°C, 55°C.
Water Pressure Adjustment
Provides four levels of washing water pressure adjustment: gentle, medium, strong, extra strong.
Nozzle Position Adjustment
Allows the spray nozzle position to be adjusted through 4 levels for improved comfort.
Soft-Close Seat and Lid
The seat and lid close slowly and quietly to reduce noise and prevent sudden closing.
Sma
Features
Automatic Flush
The lid automatically closes 8 seconds after the user leaves the seat, followed by automatic flushing.
Automatic Lid Opening/Closing
The lid opens and closes automatically when the user approaches or leaves.
Foot Sensor
Allows selected functions to be operated without hand contact for convenient and hygienic use.
Night Light
Provides a soft light to improve visibility in low-light conditions.
LED Display
Displays the operating status and selected settings for convenient operation.
Foam Shield (if applicable)
Creates a layer of foam on the water surface to help reduce splashing and minimise odours.
Safety & Technology Functions Seat Sensor
The seat sensor detects when the user is seated and enables the washing functions only when the seat is occupied.
Instant Water Heating
Provides instant water heating to deliver continuous warm water during washing.
Leakage Protection
Equipped with Residual Currem Device (RCD) to help prevent electrical hazards caused by water leakage.
Energy & Power Energy Saving Mode
Automatically enters Energy Saving Mode after 10 minutes of inactivity. The display and ambient light turn off to reduce power consumption.
Power-Outage Flushing
A battery box is provided for emergency flushing during power outages. Users only need to install AA batteries (not included). With water tank model: 10 × AA batteries Tankless model: 4 × AA batteries
-5-
LID & SEAT OPERATION MODES VOICE CONTROL (IF APPLICABLE) 1. Automatic (High & Top only) Note: Voice control isMode available on selected TOPversion version only.
The lid opens automatically when the sensor detects movement within the sensing range. The lid and seat close automatically when no operation is detected for 90 seconds. Voice Command Voice Response Function After the automatic lid opening function is activated, there is a 30-second delay before it can be activated again. Hello toilet I'm here Activates voice control. Please Note: open the lid Cover/Lid opening Opens the lid. · When the user moves slowly within the sensing area, the sensing distance may be reduced. If the lid does not respond, use the close the lid Cover/Lid closing Closes the lid. remote control or manually open/close the lid. the seat Seat"Lid opening Raisescontrol the seat. · The automaticopen lid opening/closing function works only when Opening/Closing Setting" on the remote is set to "ON". close the toilet, seat such as opening/closing doors Seat closing curtains, may trigger the lid to Lowers seat. · Movement around or moving open the automatically. If false activation occurs repeatedly due to the bathroom environment, use the remote control to disable the aautomatic full flush Toilet flushing Performs full flush. lid opening/closingstart function . cleaning Wash opening Starts the washing function. · When used by children, the sensor may not detect the user due to height limitations. close cleaning Close cleaning Stops the washing function. · Do not open or close the lid/seat manually with excessive force, as this may damage the automatic opening/closing mechanism start drying Start drying Starts warm air drying. and cause product malfunction. close drying Close drying Stops drying.
2. Footswitch Sensor Mode on the power
Turning on the power
Turns the smart toilet on.
The foot sensor allows thepower lid, seat, and flushing functions to beoff operated without hand contact. Turns the smart toilet off. switch off the Turning the power The following is the complete operation sequence of the foot sensor function. turn on the night light Turning on the lighting Turns on the night light. Open Lid: Move your foot near the foot sensor to automatically open the lid. turn off the night light Turning off the lighting Turns off the night light. Open Seat: Move your foot near the foot sensor to automatically open the seat. water temperature Water temperature has been increased Increases the water temperature. Flush: increase the Move your foot near the foot sensor to activate flushing. Close Seat: reduce the water temperature Water to temperature hasclose been the reduced Move your foot near the foot sensor automatically seat.
Decreases the water temperature.
Close Lid: Move your foot near the foot sensor to automatically closeincreased the lid. increase the seat temperature Seat temperature has been
Increases the seat temperature.
Note: Please until temperature the current operation isSeat fully temperature completed before activating another foot sensor function. reducewait the seat has been reduced Decreases the seat temperature. increase the wind temperature
Wind temperature has been increased
Increases the dryer temperature.
reduce the wind temperature Wind temperature has been reduced The lid and seat can also be opened or closed manually. boom forward Boom forward Please Note: boom backward Boom backward
Decreases the dryer temperature.
3. Manual Opening/Closing (All versions)
Moves the nozzle forward.
Moves the nozzle backward. · When manually opening or closing the lid/seat, always move it in the same direction as the mechanism movement. increase the water power Increase the water power Increases the water pressure. · Do not force the lid or seat in the opposite direction while the automatic opening/closing function is operating, as this may reduce the water power Reduce the water power Decreases the water pressure. damage the automatic mechanism. clean an obstacle during movement, Rear Starts rear wash. · If the lid or seatrear encounters it willclean stop automatically. front clean
Front clean
Starts front wash.
clean the nozzle
Clean the nozzle
Starts nozzle self-cleaning.
massage SIDE start KNOB INSTRUCTION Start massage
Starts oscillating wash.
stop massage
Stop massage
Stops oscillating wash.
move clean
Move clean
Starts oscillating wash.
Washing & drying can only be activated while seated.
move once to flush. (While not seated) Stop move 1. press stop the knob open the voice
Turn on the recongnition function
turn up the volume
Turn up the volume
Stops oscillating wash. Turns voice prompts on.
2. Rotate the knob counter-clockwise once to start Front Wash. (While seated) close the voice Turn off the recongnition function Turns voice prompts off. Rotate the knob again to start Oscillating Wash. 3. Rotate the knob clockwise once to start Rear Wash. (While seated) turn down the volume Turn down the volume Rotate the knob again to start Oscillating Wash. stop cleaning
Already stop
Increases the voice prompt volume.
Decreases the voice prompt volume.
When Front Wash or Rear Wash is activated, the cleaning cycle will run for approximately 95 seconds and stop automatically.
Stops washing.
4. Press the knob twice to start the drying function. (While seated) The drying cycle will run for approximately 2 minutes and stop automatically, or press the knob once to stop drying. 5. Press the knob to stop activative function: washing, drying, self-cleaning. (While seated)
--76--
REMOTE CONTROL LID & SEAT OPERATION MODES *The1.remote control buttons for&different versions Automatic Mode (High Top version only)of smart toilets may vary; Buttons such as "Open Lid" "Open Seat" "Half Flush" "Auto Flush" and “Seat Massage" may not be present. The lid opens automatically when the sensor detects movement within the sensing range. The lid and seat close automatically when no operation is detected for 90 seconds. After the automatic lid opening function is activated, there is a 30-second delay before it can be activated again.
Stop/Power
Auto Flush
Seat Massage
Please Note:
Press to start seat massage Press to stop any active function, Press to turn on/off the · When thewashing user moves within the sensing area, the sensing distance may be reduced.Off-seat If the lid does not respond, use the while seated, lasts for 3 minutes. including andslowly drying. flushing. remote control or manually open/close the lid.
· The automatic lid opening/closing function works only when "Lid Opening/Closing Setting" on the remote control is set to "ON". · Movement around the toilet, such as opening/closing doors or moving curtains, may trigger the lid to open automatically.
Wash/Oscillating Cleaning IfRear false Wash/Oscillating activation occurs repeatedly due to theFront bathroom environment, use the remote control to disablepressure the automatic lid opening/closing function . after Press to start Rear Wash
Press to adjust the cleaning water pressure. "+" : Increase pressure; mechanism wash cycle lasts the approximately Theexcessive wash cycle lasts approximately ·The Do not open or close lid/seat manually with force, as this may damage the automatic opening/closing "-" : Decrease pressure. 95 seconds and then stops 95 seconds and then stops and cause product malfunction. automatically. Press the button automatically. Press the button again during washing to activate again during washing to activate 2. Foot Wash. Sensor Mode Oscillating Oscillating Wash. Press to start Front Wash after
while seated.may not detect nozzlethe self-cleaning while seated. ·nozzle When self-cleaning used by children, the sensor user due to height limitations.
The foot sensor allows the lid, seat, and flushing functions to be operated without hand contact. The following is the complete operation sequence of the foot sensor function. Open Lid:
Move your foot near the foot sensor to automatically open the lid.
Open Seat:
Move your foot near the foot sensor to automatically open the seat.
Drying
Nozzle position
/
Nozzle position
/
Press to start drying the nozzle position Press to adjust the nozzle position Flush: this button Move your foot near the footPress sensortotoadjust activate flushing. while seated. Drying will stop FORWARD during rear wash or BACKWARD during rear wash or Close Seat: Move your foot near the foot sensor to automatically close the seat. automatically affer 2 minutes front wash. front wash. Close Lid: Move your foot near the foot*Disabled sensor to automatically close the lid. during oscillating *Disabled during oscillating washsensor function. Note: Please wait until the current operationwash is fully completed before activating another foot
3. Manual Opening/Closing (All versions)
seat Open Lidseat can also be opened or closedOpen The lid and manually.
Foam
Press open/close the lid. Pleaseto Note:
Press to activate the foam shield function when powered on.
Press to open/close the seat.
· When manually opening or closing the lid/seat, always move it in the same direction as the mechanism movement.
· Do not force the lid or seat in the opposite direction while the automatic opening/closing function is operating, as this may damage the automatic mechanism.
Seat Temp it will stop automatically. ·Water If the lidTemp or seat encounters an obstacle during movement,
Drying Temp
Press to adjust the cleaning Press to adjust the seat water temperature : temperature : Option 1: Room temperature Option 1: Room temperature (No heating); (No heating); Option 2: Approx 34°C; Option 2: Approx 34°C; Washing & drying seated. Option 3: Approx 37°C; can only be activated Optionwhile 3: Approx 37°C; Option 4: Approx 40°C. Option 4: Approx 40°C. 1. press the knob once to flush. (While not seated)
Press to adjust the drying air temperature : Option 1: Room temperature (No heating); Option 2: Approx 35°C; Option 3: Approx 45°C; Option 4: Approx 55°C.
SIDE KNOB INSTRUCTION
2. Rotate the knob counter-clockwise once to start Front Wash. (While seated) Rotate the knob again to startSelf-cleaning Oscillating Wash. Full Flush
Night Light
Press to activate nozzle(While seated) Press to turn on/off the Press to fullthe flushing. 3.start Rotate knob clockwise once to start Rear Wash. night light. function. Rotate the knob again to start"Self-cleaning" Oscillating Wash.
When Front Wash or Rear Wash is activated, the cleaning cycle will run for approximately 95 seconds and stop automatically.
Half flush 4. Press the knob twice to start the drying function. (While seated)
Press to start half flushing. The drying cycle will run for approximately 2 minutes and stop automatically, or press the
knob once to stop drying. 5. Press the knob to stop activative function: washing, drying, self-cleaning. (While seated)
--87--
ADVANCED REMOTE CONTROL SETTINGS
Note: Please read the following carefully before using
REMOTE CONTROL
Auto Flush After Lid/Seat Closing
1. Press andcontrol hold ‘Stop/Power’ for 3 seconds to of turn o the unit.may vary; Buttons such *The remote buttons for different versions smart toilets After Lid" power-o ‘Open Lid’Flush" for 5 seconds. as2."Open "Open, press Seat"and "Halfhold Flush" "Auto and “Seat Massage" may not be present. 2 beeps: Enable auto �ush after lid/seat closing. 1 beep: Disable auto �ush after lid/seat closing. Auto Flush Stop/Power Seat Massage 3. Turn on the unit to save the setting. Press to stop any active function, including washing and drying.
Auto Lid Opening
Rear Wash/Oscillating
Press to start seat massage while seated, lasts for 3 minutes.
Press to turn on/off the Off-seat flushing.
Front Wash/Oscillating
Cleaning pressure
Press to adjust the Press starthold Rear‘Open Wash after Press toto start Front Wash after Presstoand Lid’ for 5 seconds Enable/disable auto lid opening function: cleaning water pressure. nozzle self-cleaning while seated. nozzle self-cleaning while seated. 2 beeps: Enable auto lid opening. "+" : Increase pressure; The wash cycle lasts approximately The wash cycle lasts approximately 1 beep:and Disable auto lid opening. "-" : Decrease pressure. 95 seconds then stops 95 seconds and then stops automatically. Press the button automatically. Press the button again during washing to activate again during washing to activate Oscillating Wash. Oscillating Wash. Full Flush
/
Flush Time Adjustment
/ / Drying Nozzle position Nozzle position 1.Press and hold ‘Stop/Power’ for 3 seconds to turn o the unit. Press this button to start drying Press to adjust the nozzle position Press to adjust the nozzle position 2.Within 3 seconds, press ‘Full Flush’ once to to enter the Top Flush time adjustment. while seated. Drying will stop FORWARD during rear wash or BACKWARD during rear wash or 3.Press“∧” affer “ ∨ 2” minutes or “ < ” “ > ” to adjust the �ushing time. Each increment changes the �ushing time automatically front wash. front wash. during *Disabled during oscillating by 0.5 seconds. The display shows*Disabled a number fromoscillating 5 to 12, with 5 indicating the sho�est �ushing time wash wash and 12 indicating the longest. 4.After adjusting the Top Flush time, press 'Full Flush' to switch to Bottom Flush adjustment. Press 'Full Flush' again to switch to Re�ll adjustment. Open seat Foam Open 5.Turn Lid on the unit to save the setting. Press to activateBottom the foamFlush, shield Press open/close the lid. to open/close the seat. Note:toThe �rst press of 'Full Flush' Press activates Top Flush, the second press activates function when powered on. and the third press activates Re�ll. Water Temp
Drying Temp
Seat Temp
Press to adjust the cleaning Press to adjust the seat Auto Bowl Pre-Wetting water temperature : temperature : Full Flush Option 1: Room temperature Option 1: Room temperature (No heating); heating); to turn o the unit. 1. Press and hold ‘Stop/Power’ for(No 3 seconds Option 2: Approx 34°C; Option 2: Approx 34°C; 2. After power-o , press and hold Full Flush for 537°C; seconds. Option 3: Approx 37°C; Option 3: Approx 2 beeps: Enable Option 4: Approx 40°C.auto bowl pre-wetting Option 4: when Approxseated. 40°C.
Press to adjust the drying air temperature : Option 1: Room temperature (No heating); Option 2: Approx 35°C; Option 3: Approx 45°C; Option 4: Approx 55°C.
Full Flush
Self-cleaning
Night Light
Press to start full flushing.
Press to activate nozzle "Self-cleaning" function.
Press to turn on/off the night light.
1 beep: Disable auto bowl pre-wetting. 3. Turn on the unit to save the setting.
/
Sensor Range
1.Press and hold ‘Stop/Power’ for 3 seconds to turn o the unit. Half flush 2.Within 3 seconds, press ‘Open Lid’ to adjust. Press to 3.Use “start ∧ ”half “ ∨flushing. ” or “ < ” “ > ” to adjust the sensor range (Level 1-5). A higher setting provides a fa�her sensing range. 4.Turn on the unit to save the settings.
-8-
ADVANCED REMOTE CONTROL SETTINGS
Note: Please read the following carefully before using
/
Auto Flush After Lid/Seat Closing Lid and Seat Opening Angle Adjustment
1. Press and hold ‘Stop/Power’ for 3 seconds to turn o the unit. 1.Press and hold ‘Stop/Power’ forhold 3 seconds to turn the unit. 2. After power-o , press and ‘Open Lid’ for 5o seconds. 2.Within 3 seconds, press “∧ ” “ after ∨ ” or “ < ” “closing. > ” to activate the setting mode (Level 1-14). 2 beeps: Enable auto �ush lid/seat Note: The temperature indicator on the toilet displays 1 beep: Disable auto �ush after lid/seat closing. the current angle level. • Water Temp Indicator: (Adjust with “ ∧ ” or “ < ” ). 3. Turn on the unit to Lid saveAngle the setting. • Seat Temp Indicator: Seat Angle (Adjust with “ ∨ ” or “ > ”). 3.Press ‘Stop/Power’ to turn on the unit and save the setting.
Auto Lid Opening Press and hold ‘Open Lid’ for 5 seconds to Enable/disable auto lid opening function: 2/beeps: Enable auto lid opening. O -seat Auto Flush Full Flush Auto Flush 1 beep: Disable auto lid opening.
Note: Button functions may va� depending on the remote control model. Press 'Auto Flush' or press and hold 'Full Flush' for 5 seconds. 2 beeps: Enable auto �ush after leaving. / Flush Time Adjustment 1 beep: DisableFullauto �ush after leaving. Flush Note: The toilet will automatically �ush only if the user has been seated for more than 10 seconds. 1.Press and hold ‘Stop/Power’ for 3 seconds to turn o the unit. 2.Within 3 seconds, press ‘Full Flush’ once to to enter the Top Flush time adjustment. 3.Press“∧” “ ∨ ” or “ < ” “ > ” to adjust the �ushing time. Each increment changes the �ushing time by 0.5 seconds. The display shows a number from 5 to 12, with 5 indicating the sho�est �ushing time and 12 indicating the longest. 4.After adjustingAuto the Top FlushFunction time, press 'Full Flush' to switch to Bottom Flush adjustment. Foam Press 'Full Flush' again to switch to Re�ll adjustment. Note: This on function is to only available on the top version. 5.Turn the unit save the setting. 1.Press and hold 3 seconds turn o the Note: The �rst‘Stop/Power’ press of 'Full for Flush' activatestoTop Flush, theunit. second press activates Bottom Flush, 2.Press enable or disable the auto foam function. and ‘D�ing’ the thirdonce presstoactivates Re�ll. 2 beeps: Enable auto foam function. 1 beep: Disable auto foam function. 3.Turn on the unit to save the setting. Note: The auto foam function is disabled by default. When enabled, the foam shield function Auto Bowl Pre-Wetting Full Flush will be automatically activated once when the user is seated. 1. Press and hold ‘Stop/Power’ for 3 seconds to turn o the unit. 2. After power-o , press and hold Full Flush for 5 seconds. 2 beeps: Enable auto bowl pre-wetting when seated. 1 beep: Disable auto bowl pre-wetting. 3. Turncontrol on the unit to save the setting. Remote pairing Rotate the knob clockwise to "rear wash" for about 3 seconds till hearing a "beep" (display flashes at the same time). Then press any button on remote control to complete the pairing.
/
Sensor Range
1.Press and hold ‘Stop/Power’ for 3 seconds to turn o the unit. 2.Within 3 seconds, press ‘Open Lid’ to adjust. 3.Use “ ∧ ” “ ∨ ” or “ < ” “ > ” to adjust the sensor range (Level 1-5). A higher setting provides a fa�her sensing range. 4.Turn on the unit to save the settings.
-9-
/
Lid and Seat Opening Angle Adjustment
1.Press and hold ‘Stop/Power’ for 3 seconds to turn o the unit. REPLACING REMOTE CONTROL BATTERIES
2.Within 3 seconds, press “ ∧ ” “ ∨ ” or “ < ” “ > ” to activate the setting mode (Level 1-14). Note: The temperature indicator on the toilet displays the current angle level. The remote control requires two AAA d� batteries (Not provided). • Water Temp Indicator: Lid Angle (Adjust with “ ∧ ” or “ < ” ). • Seat Temp Indicator: Seat Angle (Adjust with “ ∨ ” or “ > ”). Please note: 3.Press ‘Stop/Power’ to turn on the unit and save the setting.
1. Do not attempt to recharge non-rechargeable batteries. 2. Rechargeable batteries are to be removed from the appliance before being charged. 3. Do not mix di erent brands of batteries or new and used batteries. 4. Ensure batteries are inse�ed with the correct polarity. 5. Dead batteries be removed from the appliance and disposed o safely. / Auto FlushareOto -seat Auto Flush Full Flush 6. Remove the batteries if the appliance is to be stored unused for a long period of time. Note: Button functions may va� depending on the remote control model. Press 'Auto Flush' or press and hold 'Full Flush' for 5 seconds. 2 beeps: Enable auto �ush after leaving. 1 beep: Disable auto �ush after leaving. Note: The toilet will automatically �ush only if the user has been seated for more than 10 seconds.
Auto Foam Function Note: This function is only available on the top version. 1.Press and hold ‘Stop/Power’ for 3 seconds to turn o the unit. 2.Press ‘D�ing’ once to enable or disable the auto foam function. 2 beeps: Enable auto foam function. 1 beep: Disable auto foam function. 3.Turn on the unit to save the setting. Note: The auto foam function is disabled by default. When enabled, the foam shield function will be automatically activated once when the user is seated.
Remote control pairing Rotate the knob clockwise to "rear wash" for about 3 seconds till hearing a "beep"
(display flashes at the same time). Then press any button on remote control to complete the pairing. WARNING
1. Batteries are hazardous and must be kept away from children (whether the battery is new or used). 2. Batte� can cause se�ere or fatal injuries within 2 hours or less if it is swallowed or inse�ed into any pa� of the body. 3. Medical attention should be sought immediately if it is suspected the batte� has been swallowed or inse�ed into any pa� of the body.
- 10 - 11 -
AROMA FUNCTION REPLACING REMOTE CONTROL BATTERIES The remote control requires two AAA d� batteries (Not provided). Please note: 1. Do not attempt to recharge non-rechargeable batteries. 2. Rechargeable batteries are to be removed from the appliance before being charged. 3. Do not mix di erent brands of batteries or new and used batteries. 4. Ensure batteries are inse�ed with the correct polarity. 5. Dead batteries are to be removed from the appliance and disposed o safely. 6. Remove the batteries if the appliance is to be stored unused for a long period of time.
Step 1: Lift up the display cover. Tear off the packaging bag and take out the aroma tablet.
Step 2: Insert the aroma tablet into the aroma slot.
Step 3: Put the cover back, ensure it is securely fitted before use.
Note: If there is no fragrance, add 2–3 drops of your favorite essential oil or fragrance to the diffuser tablet. Do not drop essential oil directly into the toilet to avoid damage.
WARNING 1. Batteries are hazardous and must be kept away from children (whether the battery is new or used). 2. Batte� can cause se�ere or fatal injuries within 2 hours or less if it is swallowed or inse�ed into any pa� of the body. 3. Medical attention should be sought immediately if it is suspected the batte� has been swallowed or inse�ed into any pa� of the body.
- 11 -
CARE ANDFUNCTION MAINTENANCE AROMA Cleaning the Toilet Clean the toilet regularly with a soft, damp cloth and mild neutral detergent. Do not use abrasive cleaners, bleach, solvents, or harsh chemicals, as they may damage the su�ace of the toilet. Avoid spraying water directly onto electrical components.
Cleaning the Nozzle Clean the spray nozzle regularly to maintain hygiene. Use a soft cloth or a soft brush to gently clean the nozzle su�ace. Do not apply excessive force to the nozzle, as this may cause damage.
Cleaning the Seat and Lid Step 2: Step 1: WipeLift the seat anddisplay lid with cover. a soft, Tear dampoff cloth. Insert the aroma tablet into up the Do not use abrasive materials strong chemical cleaners, as they may damage the aroma slot. the su�ace. the packaging bag andortake out the aroma tablet. Long-Term Storage If the toilet will not be used for an extended period: 1. Disconnect the power supply. 2. Shut o the water supply. 3. Drain any remaining water from the toilet if necessa�.
CLEANING AGENTS AND TOOLS Step 3: Put the cover back, ensure it is securely fitted before use.
Note: If there is no fragrance, add 2–3 drops of your favorite essential oil or fragrance to the diffuser tablet. Do not drop essential oil directly into the toilet to avoid damage.
For Sma� Toilet
Soft cloths, lint-free cloths
Mild cleaning agents that are kind to the skin.
Do not use the cleaning agents of strong acid and alkali To clean the Sma� Toilet, do not use the hard brush e.g. toilet brush / nylon brush
- 12 -
FOAM LIQUID REFILL Note: Available on Top version only.
TROUBLESHOOTING Fault phenomenon No power / The device cannot be turned on
No water from spray
The nozzle goes back suddenly Water dripping from nozzle
+
The washing function is not working
Low washing pressure
Fault analysis
Fault handling
Power cord loose or disconnected
Plug the power cord firmly into the outlet
PRCD plug has tripped
Press the RESET button on the PRCD plug
Step 1: Check the home's electrical panel and reset the breaker Locate the solid foaming tablets and the 480mL Water supply is shut off Wait for water supply to resume empty bottle from the accessory kit.
Household circuit breaker has tripped
Angle valve is closed
Open the angle valve
Inlet filter (if installed) is clogged
Replace the inlet filter
Water supply hose is kinked or bent
Straighten the water supply hose to remove kinks
The washing cycle is 95 seconds at Constant Temperature mode
Restart the washing function
The seat sensor may not be covered
Adjust sitting posture
Solenoid valve malfunction
Stop using the product and contact professional service personnel for maintenance
Power supply is OFF
Turn ON the power
The water inlet valve is closed
Open the water inlet valve to ensure there is a water supply
Inlet filter (if installed) is clogged
Replace the inlet filter
The water supply pressure may be too low.
Please check and ensure the water supply pressure is ≧1.5 bar (dynamic pressure)
Step 2: Sit on the seat and adjust sitting posture User is not detected on the seat cover the seat Fill the bottle with 450 mL of water,tothen add 2 sensor foaming tablets. Lid isthe closed Open the lid and sit on the seat Allow tablets to dissolve completely. Note: Dosetting not isput the cap on and shake the bottle. Washing pressure too low Adjust washing pressure according to the manual
Inlet filter (if installed) is clogged
Replace the inlet filter
Water temperature setting is too low
Adjust the water temperature via the remote control
The temperature of water supply may be too low.
Ensure the temperature of water supply is: 4-35℃
Drying / seat temperature too low or no heating
Temperature set too low
Adjust temperature settings
Dryer does not work
The user is not detected by the seat sensor
Sit on the seat and adjust sitting position to cover the seat sensor
Seat or lid drops too fast (Power-on status)
Step 3: Damper system failure
Contact professional maintenance personnel if the malfunction persists
Poor flushing at low water pressure
Too low water pressure
If the flow rate is less than 5L in 15 seconds, it is recommended to install a water booster pump
Water supply hose is bent or kinked
Ensure the water supply hose is not bent and keep it straight
Flush valve failure
Contact professional service personnel for maintenance
No batteries are installed in the remote control
Install two AAA batteries in the remote control
Low water temperature
Locate the tube fitted with the rocket-shaped plastic connector. Seat or lid can not 1. Unplug the unit for 1 minute then reconnect power the connector prepared foaming professional solution.service auto open/close Soft-closeInsert (damper) system malfunctioninto the 2. If the issue persists,contact (For auto flip models only) personnel for maintenance. Tighten the cap on the tube securely. Place the bottle in a stable Inlet filter (if installed) is clogged the inlet filter following location where it cannot beClean easily knocked over.manual instructions
Poor flushing at normal
water pressure Warning: Keep the bottle out of the reach of children and pets.
Remote control not working
Battery power is too low
Replace the batteries
The toilet code and remote control code do not match
Pair the remote control code
- 15 -
- 13 -
CARE AND MAINTENANCE Cleaning the Toilet
INSTALLATION
Clean the toilet regularly with a soft, damp cloth and mild neutral detergent. Do not use abrasive cleaners, bleach, solvents, or harsh chemicals, as they may damage the su�ace of the toilet. Avoid spraying water directly onto electrical components.
Important !
All installations must comply with local regulations. Cleaning the Nozzle Clean the spray nozzle regularly to maintain hygiene. Installation must be carried out by a licensed plumber. Any electrical work, if required, must be performed Use a soft cloth or a soft brush to gently clean the nozzle su�ace. by not a licensed electrician in accordance with localdamage. regulations. Do apply excessive force to the nozzle, as applicable this may cause
Cleaning the Seat and Lid
NOTE:
Wipe the seat and lid with a soft, damp cloth. Do not use abrasive materials or strong chemical cleaners, as they may damage the su�ace. Australia & New Zealand
Long-Term Storage
Important:
If the toilet will not be used for an extended period: 1. Disconnect the power supply. 2. Shut o the water supply. Installation is subject to the requirements of the applicable regulatory authority, the National 3. Drain any remaining waterThree from the toilet if necessa�. Construction Code Volume - Plumbing Code of Australia, associated reference standards as applicable at the time and AS/NZS 3500
CLEANING AGENTS AND TOOLS Notes for installation 1. PLEASE ENSURE PIPEWORK IS FLUSHED CLEAR OF DEBRIS BEFORE 2. INLET PRESSURE RANGE 100 – 500KPA 3. AS/NZS 3500 REQUIRES 500 KPA MAXIMUM OPERATING PRESSURE AT ANY OUTLET WITHIN A BUILDING
For Sma� Toilet
※ Please read this manual thoroughly before using the product. ※ Please do not Soft hesitate to contact us if you have any questions in the installation or usage. cloths, ※ Please safekeeping thiscloths manual after reading. lint-free
Mild cleaning agents that are kind to the skin.
Do not use the cleaning agents of strong acid and alkali To clean the Sma� Toilet, do not use the hard brush e.g. toilet brush / nylon brush
- 14 -
TROUBLESHOOTING Fault phenomenon
Safety precautions
Fault analysis
Fault handling
In order to avoid injuryPower andcord property please follow the safety warnings and loose or loss, disconnected Plug the power cord firmly into the outlet No power /Read this manual carefully before installation, and then install it precautions. The device cannot PRCD plug has tripped Press the RESET button on the PRCD plug be turned on accordance with the instructions. After you have finished reading, please keep Household circuit breaker has tripped Check the home's electrical panel and reset the breaker the instructions for the end user. No water from spray
Water supply is shut off
Wait for water supply to resume
Angle valve is closed
Open the angle valve
Water supply hose is kinked or bent
Straighten the water supply hose to remove kinks
It means that if you ignore this sign
WARNINGInletIt filter installed) is clogged injury or propertyReplace the inlet filter may(ifcause personal damage Below itemsThe arewashing prohibbted cycle is 95 seconds at
The nozzle goes back suddenly
Constant Temperature mode
The seat sensor may not be covered
Adjust sitting posture
Solenoid valve malfunction
Stop using the product and contact professional service personnel for maintenance
Power supply is OFF
Turn ON the power
These are compulsory requirementrs
Water dripping from nozzle
Restart the washing function
WARNING Open the water inlet valve to ensure there is a water supply
The water inlet valve is closed
The washing function Inlet filter (if installed) is clogged Replace the inlet filter is not working Please stop using if the seat cover malfunctions Sit on the seat and adjust sitting posture is not detected on the seat close the water-in�ow Please cut User o the power supply,and tosensor stop water to covervalve the seat
supply if following cases happen: Lid is closed
Open the lid and sit on the seat
Washing pressure setting is too low Adjust washing pressure according to the manual Faults: Excessive heating; smoking; Abnormal sound and odour;Products cracks,damages;or blocked. Please check and ensure the water supply The water supply pressure may
Low washing pressure
be too low.
pressure is ≧1.5 bar (dynamic pressure)
Water temperature setting is too low
Adjust the water temperature via the remote control
It may cause electric shock,inju�,�re or indoor problems if you continue to use it Inlet filter (if installed) is clogged Replace the inlet filter when it is malfunctioning.
Low water temperature Please doThe not use gasoline, brush and other non-neutral temperature of waterdetergent, supply may nylon Ensure the temperature of water supply is: 4-35℃ be too low. cleaning agent to clean the seat cover and other plastic pa�s. �therwise, it may
cause a chemical reaction or crack, Drying / seat temperature Temperature set too low too low or no heating
which will lead to injuries.
Adjust temperature settings
Dryer does not work
The user is not detected by the seat sensor
Sit on the seat and adjust sitting position to cover the seat sensor
Seat or lid drops too fast (Power-on status)
Damper system failure
Contact professional maintenance personnel if the malfunction persists
Seat or lid can not auto open/close Soft-close (damper) system malfunction (For auto flip models only)
Poor flushing at low water pressure
Poor flushing at normal water pressure
Remote control not working
1. Unplug the unit for 1 minute then reconnect power 2. If the issue persists,contact professional service personnel for maintenance.
Inlet filter (if installed) is clogged
Clean the inlet filter following manual instructions
Too low water pressure
If the flow rate is less than 5L in 15 seconds, it is recommended to install a water booster pump
Water supply hose is bent or kinked
Ensure the water supply hose is not bent and keep it straight
Flush valve failure
Contact professional service personnel for maintenance
No batteries are installed in the remote control
Install two AAA batteries in the remote control
Battery power is too low
Replace the batteries
The toilet code and remote control code do not match
Pair the remote control code
- 15 -
INSTALLATION Important !
WARNING
All installations must comply with local regulations. Make sure that this product is correctly attached to a grounded connection. (If the product is carried not grounded,it may introduce the riskelectrical of electric shock) Installation must be out by a licensed plumber. Any work, if required, must be performed by a licensed electrician in accordance withconnection,or applicable local regulations. Please do not use a loose power it may cause electric shock or cause �re.
Please do not spray detergent, water, cleaning agent in or around the power supply, this may cause electric shock or �re.
NOTE:Always use the speci�ed supply voltage (240VAC, 50Hz)
Australia &Prior NewtoZealand the installation,a suitable electrical connection should be available,according to the current local legislation.
Rainwater, demineralized water, sea water or grey water are not suitable to operate
this equipment. Operate with normal drinking water only. Important:
Recommended water pressure is between 100-500Kpa Installation is subject to the requirements applicable regulatory authority, the National Recommended water temperateof is the between 4-35°C Construction Code Volume Three - Plumbing Code of Australia, associated reference only mild detergent soft cleaning standardsUse as applicable at the timeand andaAS/NZS 3500 cloth for cleaning the seat and surrounding pan, (Enjo or similar micro �bre cleaning products are suitable) Typical toilet cleaning procedures for inside pan are suitable. Bleach or chlorine-based products should not be left inside the pan with the seat shut or for prolonged periods. Standing on the seat, using the seat for a plank or any use outside of a typical weight not
can cause damage to the seat and will void the warranty. The smart toilet Notesevenly fordistributed installation
must be installed by recognized professional tradespeople. i.e. Plumber and Electricians. 1. PLEASE ENSURE PIPEWORK IS FLUSHED CLEAR OF DEBRIS BEFORE Use only Watermark approved �exible hoses for this installation. 2. INLET PRESSURE RANGE 100 – 500KPA 3. AS/NZSDo 3500 KPA MAXIMUM PRESSURE AT ANY OUTLET WITHIN A by notREQUIRES attempt to500 disassemble and/orOPERATING repair the product without authorization, any work BUILDING non-professionals will void the warranty and may cause damage to the product. ※ Please read this manual thoroughly before using the product. ※ Please do not hesitate to contact us if you have any questions in the installation or usage. ※ Please safekeeping this manual after reading.
WARNING Make sure the power supply is cut o when the product is maintained, or it may cause an electric shock or �re. Please make sure that the power is correctly connected to the AC 240V/50Hz power socket, or it may cause electric shock or �re. An isolated ciruit breaker is necessa� and required Please turn o power before taking out the smart seat or it may cause electric shock. Please ensure the bathroom is ventilated to make sure the atmosphereis suitable, as the smart toilet is an electric appliance product, please do not install in the place with high moisture or somewhere easy to get wet. Otherwise, it may cause electric shock or �re. Please close the water-in�ow valve if water leakage, and ask the professional person to repair it, or it may lead the damage of products.
- 16 -
Safety precautions In order to avoid injury and property loss, please follow the safety warnings and WARNING precautions. Read this manual carefully before installation, and then install it accordance with the turn instructions. After, you please keep Please off inlet valves drainhave waterfinished out fromreading, toilet and cut the power when not the instructions for the end user. using products for a long time . Please through the water when you use this product
again , to prevent water quality problems , which will cause skin diseases . Otherwise , it may cause electric shock , injury or fire.
It means that if you ignore this sign
WARNING It may cause personal injury or property damage
Please tighten each waterway connection when installing it or it may cause water leakage.
Below items are prohibbted Please pay attention to socket and installation position.
Please set the leakage protector in the socket circuit or insulation transformer(1.5KVA3KVA). These are compulsory requirementrs Power socket installation location should at least 0.3 m above the floor, and keep away from objects out of water such as shower and bathtub. Otherwise it may cause water leakage.
WARNING Please turn off power before cleaning products and do not clean products with water directly or it may cause electric shock or fire. Please stop using if the seat cover malfunctions Pleasecut puto the product the shade or the the products may fadevalve or burnt on the surface. Please the powerinsupply,and close water-in�ow to stop water supply if following cases happen: Please increase indoor temperature and make sure the water is flowable before using
Faults: Excessive smoking; to avoid damageheating; in cold region, or it may cause products damaged or water leakage. Abnormal sound and odour;Products cracks,damages;or blocked.
Please make sure the power supply and inlet valves are turned off before taking cover
It may cause shock,inju�,�re or indoor problems if you continue to use it off the seat,electric or it may cause electric shock or fire. when it is malfunctioning.
This appliance cangasoline, be used by children aged 8 years and above and persons with Please do not use detergent, nylonfrom brush and other non-neutral reduced physical, sensory or mental capabilities or lack of experience and knowledge if cleaning agent to clean the seat cover and other plastic pa�s. �therwise, it may they have been given supervision or instruction concerning use of the appliance in a safe cause a chemical reaction or crack, which will lead to injuries. way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
- 17 -
WARNING Bill ofMake Material sure that this product is correctly attached to a grounded connection. (If the product is not grounded,it may introduce the risk of electric shock)
Parts: Please do not use a loose power connection,or it may cause electric shock or cause �re.
4. Please do not spray detergent, water, cleaning agent in or around the power supply, this Floor Fixing Kit : 5. may cause electric shock or �re. 1. 2. (240VAC, 3. Always use the speci�ed supply voltage 50Hz) 1. Screw Cover 6. 2. Bracket to pan fixing screw Prior to the installation,a suitable electrical connection should be available,according to the 3. Screwcurrent cup local legislation. 4. Floor ‘L-shaped’ fixing bracket
Rainwater, demineralized water, sea water or grey water are not suitable to operate
5. Floor screw this equipment. Operate with normal drinking water only. 6. Screw washer
Recommended water pressure is between 100-500Kpa Recommended water temperate is between 4-35°C
7. Rawl plug
7.
Use only mild detergent and a soft cleaning cloth for cleaning the seat and surrounding pan, (Enjo or similar micro �bre cleaning products are suitable) Typical toilet cleaning procedures for inside pan are suitable. Bleach or chlorine-based products should not be left inside the pan with the seat shut or for prolonged periods. Standing on the seat, using the seat for a plank or any use outside of a typical weight not evenly distributed can cause damage to the seat and will void the warranty. The smart toilet Floor Fixing Kit Angle Valvei.e. Plumber andTee Remoteprofessional Control must be installed by recognized tradespeople. Electricians. Use only Watermark approved �exible hoses for this installation. Do not attempt to disassemble and/or repair the product without authorization, any work by non-professionals will void the warranty and may cause damage to the product. Mounting Template
●★
●
Sewage/Waste Pipe (P-trap)
Dual Check Valve
● You may need to purchase it yourself.
●
Sewage/Waste Pipe (S-trap)
WARNING ★ Only for Australia/New Zealand.
Make sure the power supply is cut o when the product is maintained, or it may cause an electric shock or �re.
Tools required for installation (not supplied)
Please make sure that the power is correctly connected to the AC 240V/50Hz power socket, or it may cause electric shock or �re. An isolated ciruit breaker is necessa� and required Please turn o power before taking out the smart seat or it may cause electric shock.
Pencil
Tape Measure
Power Drill
Spirit Level
Hacksaw
Please ensure the bathroom is ventilated to make sure the atmosphereis suitable, as the smart toilet is an electric appliance product, please do not install in the place with high moisture or somewhere easy to get wet. Otherwise, it may cause electric shock or �re. Please close the water-in�ow valve if water Siliconeleakage, and ask the professional Standard Ruler person to repair it,Spanner or it may lead the damage Sealant of products.
Screwdriver
- 20 -
- 18 -
Pre-installation Check
WARNING
Please turn off inlet valves , drain water out from toilet and cut the power when not
products for a long time . Please through the water when you use this product Installationusing Diagram again , to prevent water quality problems , which will cause skin diseases . Otherwise , it may causeand electric shock , injury or fire. External angle valve power supply: Floor-Outlet (S-trap 50~220mm)
Please tighten each waterway connection when installing it or it may cause water leakage.
Please pay attention to socket and installation position. Waterproof, splash proof 10A socket Size unit : CM Please set the leakage protector in the socket circuit or insulation transformer(1.5KVAwith ground fault circuit breaker 3KVA). Power socket installation location should at least 0.3 m above the floor, and keep away from objects out of water such as shower and bathtub. Otherwise it may cause water leakage. Please turn off power25±1 before cleaning products and do not clean products with water
Socket directly or it may cause electric shock or fire.
Please put the product in the shade or the products may fade or burnt on the surface. 28±1 Inlet water R1/2
（Wall Inlet） 15 Please increase indoor temperature and make sure the water is flowable before using to avoid damage in cold region, or it may cause products damagedWall or water leakage.
>30
5-22 Please make sure the power supply and inlet valves are turned off before taking cover off the seat, or it may cause electric shock or fire. This appliance can be used Ground by children aged from 8 years and above and persons with Sewage outlet reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand thedrain hazards involved. Toilet installation Cut pipes
at ground level
Children shall not play with the appliance.
center line
Cleaning and user maintenance shall not be made by children without supervision. The appliance is not to besupply: used by Floor-outlet persons (including children) with reduced physical, ① External angle valve and power (S-trap) installation sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
1. Measure the rough-in distance for the floor-outlet toilet (from the finished tiled wall surface to the center of the waste pipe); cut the wall-mounting threaded rods for the waste pipe according to this distance.
- 19 -
Bill of Material Parts:
4.
Floor Fixing Kit :
1.
1. Screw Cover
2.
5.
3.
6.
2. Bracket to pan fixing screw 3. Screw cup 4. Floor ‘L-shaped’ fixing bracket 5. Floor screw
Screwthe washer 2.6.Align mounting template with the floor drainage pipe and position it against the wall; 7.mark Rawl the pluglocations for the mounting screws, drill the holes, and install 7. the L- shaped fixing bracket in the sequence shown in the diagram.
Floor Fixing Kit
Mounting Template
Angle Valve
Remote Control
●★
●
Sewage/Waste Pipe (P-trap)
Dual Check Valve
Tee
●
Sewage/Waste Pipe (S-trap)
3. Mark the edges of the mounting plate with a pen, then remove the plate;
★ Only for Australia/New Zealand.
● You may need to purchase it yourself.
Tools required for installation (not supplied)
Pencil
Tape Measure
Power Drill
Spirit Level
Hacksaw
4. Open the smart toilet lid and seat, remove the screw mounting hole covers, loosen the screws, lift the seat cover device upwards, disconnect the three electrical wires, and remove the seat cover device. Silicone Screwdriver
Spanner
Sealant
- 20 -
Standard Ruler
Pre-installation Check Installation Diagram External angle valve and power supply: Floor-Outlet (S-trap 50~220mm) Waterproof, splash proof 10A socket with ground fault circuit breaker
Size unit : CM
5. Place the ceramic toilet at the marked position on the template, back against the wall and aligned with the marked edges, then tip the toilet onto its side. 25±1 Socket 28±1
15
Inlet water R1/2 （Wall Inlet） Wall
>30
5-22 Ground
Sewage outlet
Cut drain pipes at ground level
Toilet installation center line
6. Align one end of the sewage/waste pipe with the floor drain opening and position the other end parallel to the ceramic toilet's waste outlet; mark the location of the toilet outlet's edge on the waste pipe, then cut the pipe, allowing an extra 10–20 mm beyond that mark. ① External angle valve and power supply: Floor-outlet (S-trap) installation
7. Connect the waste pipe to the wall-mounting bracket and insert it into the waste outlet; 1. Measure the rough-in distance for the floor-outlet toilet (from the finished tiled wall surface adjust the center height of the waste outlet to 180 mm above the finished floor. Mark the to the center of the waste pipe); cut the wall-mounting threaded rods for the waste pipe mounting positions for the bracket on the wall, drill the holes, then install and securely according to this distance. tighten the wall-mounting bracket.
- 21 -
- 23 -
2. Align the mounting template with the floor drainage pipe and position it against the wall; mark the locations for the mounting screws, drill the holes, and install the L- shaped fixing 8. Place the seat cover back onto the ceramic toilet; verify that the water supply hoses for the bracket in the sequence shown in the diagram. water tank & bidet are properly installed; and pull the power cord, the backup battery box wire and the other end of the water supply hoses out through the semi-circular opening on the side of the ceramic toilet.
3. Mark the edges of the mounting plate with a pen, then remove the plate; 9. Lift the toilet and place it in the installation position; slightly shift the seat cover, align the toilet's waste outlet with the waste pipe, and push the toilet toward the wall to ensure a tight connection.
4. Open the smart toilet lid and seat, remove the screw mounting hole covers, loosen the liftthe thethree seat cover device upwards, thecover three with electrical wires, and remove 10.screws, Connect wires of the seat cover,disconnect align the seat the ceramic toilet, the seat cover device. tighten the screws, and attach the screw hole covers.
- 22 - 24 -
5. Place the ceramic toilet at the marked position on the template, back against the wall and withbracket the marked edges, tip through the toiletthe onto its side. 11.aligned Insert the to pan fixingthen screws holes on both sides of the ceramic toilet and tighten them; install the screw caps (use silicone sealant to seal the contact area between the toilet base and the floor).
6. Align one end of the sewage/waste pipe with the floor drain opening and position the other ★ parallelthe to the toilet's waste location ofconnect the toilet 12.end Connect tee, ceramic dual check valve , andoutlet; angle mark valvethe in sequence, theoutlet's water edge supply on the waste pipe, then cut the pipe, anthe extra 10–20 mm beyond that mark. hoses to the tee; then plug the powerallowing cord into outlet. ★ -Only for Australia/New Zealand.
7. Connect the waste pipe to the wall-mounting bracket and insert it into the waste outlet; adjust the center height of the waste outlet to 180 mm above the finished floor. Mark the mounting positions for the bracket on the wall, drill the holes, then install and securely tighten the wall-mounting bracket.
- 23 -
Pre-installation Check Installation Diagram External angle valve and power supply: Wall-Outlet (P-trap 180mm) Waterproof, splash proof 10A socket
Size unit : CM
ground fault circuit breaker 8. Place the with seat cover back onto the ceramic toilet; verify that the water supply hoses for the water tank & bidet are properly installed; and pull the power cord, the backup battery box wire and the other end of the water supply hoses out through the semi-circular opening on the side of the ceramic toilet. Water inlet Sewage 25±1 outlet Socket 28±1
15
>30
Wall
18
Ground
9. Lift the toilet and place it in the installation position; slightly shift the seat cover, align the Toilet installation toilet's waste outlet with the waste pipe, and push the toilet toward the wall to ensure a center line tight connection. ② External angle valve and power supply: Wall-outlet (P-trap) installation
10. Connect the three wires of the seat cover, align the seat cover with the ceramic toilet, tighten the screws, and attach the screw hole covers. 1. Align the centerline of the mounting template with the centerline of the wall-mounted waste pipe and position it flush against the wall; mark the locations for the mounting screws, drill the holes, and install the L-shaped fixing bracket in the sequence shown in the diagram.
- 24 -
11. Insert the bracket to pan fixing screws through the holes on both sides of the ceramic toilet 2. Mark the edges of the mounting plate with a pen, then remove the plate; and tighten them; install the screw caps (use silicone sealant to seal the contact area between the toilet base and the floor).
★
12. Connect the tee, dual check valve , and angle valve in sequence, connect the water supply 3. Open the smart toilet lid and seat, remove the screw mounting hole covers, loosen the hoses to the tee; then plug the power cord into the outlet. screws, lift the seat cover device upwards, disconnect the three electrical wires, and remove ★ -Only for Australia/New Zealand. the seat cover device.
L
L
L
4. Fit the wall-discharge waste pipe into the ceramic toilet's waste outlet and press it firmly in place; use a ruler and a pen to mark the excess length of the pipe. Measure the width of the sealing ring at the end of the pipe, add this width to the previously marked line, cut off the excess section of the pipe, and then install the sealing ring.
- 25 - 27 -
Pre-installation Check Installation Diagram External angle valve and power supply: Wall-Outlet (P-trap 180mm) Waterproof, splash proof 10A socket with ground fault circuit breaker
Size unit : CM
5. Detach the waste pipe from the ceramic toilet and insert it into the wall-mounted waste pipe, ensuring the sealing ring is fully seated inside the wall-mounted pipe. Water inlet Sewage 25±1 outlet Socket 28±1
15
>30
Wall
18
Ground Toilet installation center line 6. Place the seat cover back onto the ceramic toilet; verify that the water supply hoses for the water tank & bidet are properly installed; and pull the power cord, the backup battery box wire and the other end of the water supply hoses out through the semi-circular opening ② External angle valve and power supply: Wall-outlet (P-trap) installation on the side of the ceramic toilet.
1. Align the centerline of the mounting template with the centerline of the wall-mounted waste 7. Lift the toilet and place it in the installation position; shift the seat cover slightly aside, align pipe and position it flush against the wall; mark the locations for the mounting screws, drill the toilet's waste outlet with the waste pipe, and push the toilet toward the wall to ensure a the holes, and install the L-shaped fixing bracket in the sequence shown in the diagram. tight connection.
- 26 - 28 -
2. Mark the edges of the mounting plate with a pen, then remove the plate; 8. Connect the three wires of the seat cover, align the seat cover with the ceramic toilet, tighten the screws, and attach the screw hole covers.
3. Open the smart toilet lid and seat, remove the screw mounting hole covers, loosen the 9. Insert the bracket to pan fixing screws through the holes on both sides of the ceramic toilet screws, lift the seat cover device upwards, disconnect the three electrical wires, and remove and tighten them; install the screw caps (use silicone sealant to seal the contact area the seat cover device. between the toilet base and the floor).
L
L
L
★
10.the Connect the tee, dual check valve andceramic angle valve in sequence, connect the water supply 4. Fit wall-discharge waste pipe into, the toilet's waste outlet and press it firmly in hoses toathe tee; then plugtothe power intolength the outlet. place; use ruler and a pen mark thecord excess of the pipe. Measure the width of the ★ -Onlyring for Australia/New sealing at the end of Zealand. the pipe, add this width to the previously marked line, cut off the excess section of the pipe, and then install the sealing ring.
- 29 -
- 27 -
Remote control installation Installation method of expansion screw 1. Place the remote control holder at the installation location, use a spirit level to ensure it is level, and then mark the positions of the screw holes on the wall with a pen. 2. Remove the holder, holes the marked on the and wall-mounted insert the 5. Detach the waste pipedrill from the at ceramic toilet spots and insert it wall, into the waste expansion/rawl plug. pipe, ensuring the sealing ring is fully seated inside the wall-mounted pipe. 3. Place the remote control holder at the installation location, align it with the screw holes, insert the mounting screws, and tighten them. 4. Place the remote control into the holder.
Adhesive installation method 1. Place the remote control holder at the installation location, use a spirit level to ensure it is level, and then mark the edges of the bracket on the wall with a pen. 2. Peel off the adhesive film from the holder, align it with the markings on wall, press it firmly wall, andonto ensure is securely attached. 6. Place the onto seat the cover back theit ceramic toilet; verify that the water supply hoses for the
water tank & bidet are properly installed; and pull the power cord, the backup battery box 3. Wait 24 hours before placing the remote control into the holder. wire and the other end of the water supply hoses out through the semi-circular opening on the side of the ceramic toilet.
7. Lift the toilet and place it in the installation position; shift the seat cover slightly aside, align the toilet's waste outlet with the waste pipe, and push the toilet toward the wall to ensure a tight connection.
Product specifications and features are subject to change without prior notice. Please refer to the actual product.
28---30 - 31 -