NVC AMENITY BROCHURE 12PP

AMENITY LIGHTING Range of highly efficient surface mounted luminaires

AMENITY LIGHTING

Lighting for STAIRWELLS & CORRIDORS Lighting these areas is safety critical, but getting it right is technically demanding.

Our range of lighting for stairwells and corridors has been thoroughly overhauled and upgraded making it one of the most comprehensive and best performing offerings in the market today.

Typically, our LED fittings offer 50% energy savings over the 2D fittings they replace, with up to 100% extra light as well – so you not only save money by upgrading to LED, you get better lighting too.

Across the range, we have paid as much attention to the light output in emergency mode as in mains mode – so

you are assured of lighting that is compliant with the latest standards in the event of an emergency.

Lighting for stairwells and corridors should not be left to chance. Our lighting design department is here to help you get it right, with the right fittings, delivering the right light levels in mains and emergency mode.

IF YOUR CLIENT HAS LEFT IT UP TO YOU, YOU CAN LEAVE IT UP TO US!

LED AMENITY PRODUCT AVAILABILITY PENTLAND

PORTLAND

ADDISON

IP44

IP54

IP40

IP65

COMMERCIAL INDOOR

COMMERCIAL INDOOR/ OUTDOOR

PAGE 3

IP Rating Application

PAGE 4

COMMERCIAL INDOOR

COMMERCIAL INDOOR

1,220 lm

1,270 lm

1,655 lm

1,610 lm

PAGE 6

SPARTAN PAGE 8

WATTAGE 15W

1,310 lm

17W 18W 21W

1,710 lm 2,200 lm

LIGHT OUTPUT The lumen figures quoted here, elsewhere in this brochure, our catalogue and on our product packaging are “luminaire lumens”. This is the actual output of the fitting, with the diffuser or controller fitted. This is the approach demanded by the internationally recognised standard, LM79.

Some manufacturers quote lumen outputs that are “LED lumens” – the output of the LEDs before the diffuser or controller is fitted. This can be very misleading.

Take care when comparing lumen outputs to ensure that you are comparing like with like.

MAKE THE SWITCH TO LED We now have LED Amenity products for every application that deliver more light, for less watts, than both 28W and 38W 2D. In all cases, LED DELIVERS MORE LIGHT FOR LESS POWER than the nearest equivalent 2D fitting.

2 // AMENITY LIGHTING

+44 (0)121 457 6340 // www.nvcuk.com

AMENITY LIGHTING

PENTLAND Slim IP44 polycarbonate LED bulkhead fittings for commercial indoor areas

OPTIONAL SNAP-ON WHITE OR CHROME BEZELS AVAILABLE SEPARATELY

APPLICATIONS

TECHNICAL DETAILS

- For commercial interior use in corridors, stairs, toilets and changing rooms CONSTRUCTION

- Polycarbonate white base - Polycarbonate opal diffuser

OPTIONS

15W, 1,220 lm, 81 l.lm/c.W CRI >80 CCT 5000K Emergency converted versions available as listed MW sensor versions available as listed

BEZEL ATTACHMENTS Optional decorative “snap fit” bezels available in a choice of white (WH) or chrome (CH) as listed

-G asket between base and diffuser to ensure IP44 rating is maintained - Gear tray secured to base with screws and retaining strap for easy maintenance - LEDs on metal core PCB

FITTING

ORDER CODE

DESCRIPTION

NPT15/WH/M3/850

Pentland 15W LED IP44 White Base M3 850

NPT15/WH/MW/850

Pentland 15W LED IP44 White Base MW 850

NPT15/WH/MW/M3/850

Pentland 15W LED IP44 White Base MW M3 850

BEZEL

ACCESSORIES NPT/BEZEL/CH

Pentland Bezel Trim Chrome

NPT/BEZEL/WH

Pentland Bezel Trim White

+44 (0)121 457 6340 // www.nvcuk.com

AMENITY LIGHTING // 3

AMENITY LIGHTING

PORTLAND LED IP54 decorative LED bulkhead fittings for commercial indoor areas

AVAILABLE WITH MICROWAVE SENSOR FITTED

CCT SELECTABLE 4000K/5000K

APPLICATIONS

TECHNICAL DETAILS

TECHNICAL DETAILS (contd.)

- For commercial interior use in corridors, - Two wattages available: DIMMING Dim-to-10% (Corridor Function) stairs, toilets and changing rooms • 15W, 1,270 lm, 85 l.lm/c.W available on all variants. Suffix CF. As • 18W, 1,610 lm, 89 l.lm/c.W listed CONSTRUCTION - CRI >80 SENSOR Available with built in micro- Polycarbonate base and bezel - CCT selectable 4000K/5000K wave sensor. Suffix MW. As listed - Micro-prismatic polycarbonate controller - ENEC approved, flicker free, LED driver DIMMING & SENSOR A popular - Available with either a White bezel (WH) - Emergency maintained 3 hours versions combination is corridor function & micro or Chrome bezel (CH), as listed (suffix M3) available, as listed wave sensor. Suffix CFMW. As listed

30

160

87

CABLE ENTRY

325

4 // AMENITY LIGHTING

100

Ø50 PCD 160

ORDER CODE

DESCRIPTION

NPO15/WH/O/840-850

Portland 15W LED IP54 White Opal 840-850

NPO15/WH/O/M3/840-850

Portland 15W LED IP54 White Opal M3 840-850

NPO18/WH/O/840-850

Portland 18W LED IP54 White Opal 840-850

NPO18/WH/O/M3/840-850

Portland 18W LED IP54 White Opal M3 840-850

NPO15/CH/O/840-850

Portland 15W LED IP54 Chrome Opal 840-850

NPO15/CH/O/M3/840-850

Portland 15W LED IP54 Chrome Opal M3 840-850

NPO18/CH/O/840-850

Portland 18W LED IP54 Chrome Opal 840-850

NPO18/CH/O/M3/840-850

Portland 18W LED IP54 Chrome Opal M3 840-850

NPO15/CF/MW/WH/O/840-850

Portland 15W LED IP54 White Opal CF MW 840-850

NPO15/CF/MW/WH/O/M3/840-850

Portland 15W LED IP54 White Opal CF MW M3 840-850

NPO15/WH/O/MW/840-850

Portland 15W LED IP54 White Opal MW 840-850

NPO15/WH/O/MW/M3/840-850

Portland 15W LED IP54 White Opal MW M3 840-850

NPO18/WH/O/MW/840-850

Portland 18W LED IP54 White Opal MW 840-850

NPO18/WH/O/MW/M3/840-850

Portland 18W LED IP54 White Opal MW M3 840-850

+44 (0)121 457 6340 // www.nvcuk.com

AMENITY LIGHTING

PORTLAND LED

Of all our amenity fittings, this is the most popular...

It is widely used in corridors, but the IP54 rating makes it suitable for bathrooms and toilets too. Delivering up to 89 luminaire lumens per circuit watt, it is also very efficient and qualifies for an Enhanced Capital Allowance (ECA).

MICRO-PRISMATIC CONTROLLER. Special polycarbonate micro-prismatic controller contributes to the high efficiency of the PORTLAND. Rather than rely only on opal material to diffuse the light we use micro-prisms on the inner face of the cover.

NO LED IMAGE. Some cheaper alternatives to the PORTLAND look great when they are switched off, but when they are switched on the individual LEDs are visible. They might rival our efficiency, but without the micro-prismatic controller they can’t rival the good looks.

CCT SELECTABLE. Selectable switch to change colour temperature between 4000K and 5000K

CHOICE OF BEZELS. PORTLAND comes complete with either a white or a chrome finish bezel.

GASKET between base and controller to maintain the IP54 rating.

PORTLAND can be supplied with corridor function (dim-to-10%).

PORTAND is available with an integral micro-wave sensor.

PORTLAND with a micro-wave sensor is a great solution for corridors - Not all fittings need a sensor. You can have one at each end of the corridor and one or two in the middle, depending on its length. These are the “master” fittings.

- The terminal block in the master fittings all have a switch-live output from the sensor – route this to the “slave” fittings.

- Order all fittings with corridor-function - Order two or more fittings with a micro-wave sensor (one for each end, plus one or two in the middle).

- At installation, run the switched-live - output from the micro-wave fittings in parallel to all the others.

- When anyone enters the corridor, from either end or from the middle, the lights will all brighten from 10% up to 100%.

This has lots of benefits: - It is easy to install – why fit two separate devices (luminaire AND sensor) when you could just fit one?

- It looks better than a separate, stand-alone, sensor - The sensor is protected behind the tough, IP54 rated cover on the fitting.

No risk it gets damaged.

+44 (0)121 457 6340 // www.nvcuk.com

AMENITY LIGHTING // 5

AMENITY LIGHTING

ADDISON IP40 decorative circular LED fitting for commercial indoor areas

AVAILABLE WITH MICRO-WAVE SENSOR FITTED

CCT SELECTABLE 4000K/5000K

ADDISON WITH WHITE BODY ADDISON WITH CHROME BODY

APPLICATIONS

TECHNICAL DETAILS

OPTIONS

- For commercial interior use in corridors - 20W, 2,200 lm, 107 l.lm/c.W DIMMING DD (DALI or Switch Dim) or CF and stairwells - CRI >80 (Corridor Function) available. Add suffix - The high light-output is designed to - CCT selectable 4000K/5000K DD or CF as required. deliver cost effective lighting designs - ENEC approved, flicker free, LED driver SPECIALIST EMERGENCY Self-Test compliant with BS12464 and BS5266.

- Emergency maintained 3 hours versions Emergency (Suffix STM3) or DALI (suffix M3) available, as listed Addressable Emergency (Suffix M3DA) - SENSOR Available with built in micro- CONSTRUCTION options available. wave sensor. Suffix MW. As listed - Circular steel base - DIMMING & SENSOR A popular - Opal acrylic diffuser combination is corridor function & - LEDs on metal core PCB micro-wave sensor. Suffix CFMW. As - Body available in White (WH) or listed Chrome (CH) as listed

6 // AMENITY LIGHTING

ORDER CODE

DESCRIPTION

NAD22/WH/840-850

Addison 22W LED IP40 White Base 840-850

NAD22/WH/M3/840-850

Addison 22W LED IP40 White Base M3 840-850

NAD22/WH/MW/840-850

Addison 22W LED IP40 White Base MW 840-850

NAD22/WH/MW/M3/840-850

Addison 22W LED IP40 White Base MW M3 840-850

NAD22/WH/CFMW/840-850

Addison 22W LED IP40 White Base CF MW 840-850

NAD22/WH/CFMW/M3/840-850

Addison 22W LED IP40 White Base CF MW M3 840-850

NAD22/CH/840-850

Addison 22W LED IP40 Chrome Base 840-850

NAD22/CH/M3/840-850

Addison 22W LED IP40 Chrome Base M3 840-850

+44 (0)121 457 6340 // www.nvcuk.com

AMENITY LIGHTING

ADDISON

was specifically designed for stairwells Achieving the light levels advised in EN12464 on stairs and half landings, in both standard and emergency mode, requires fittings with a higher output than are generally needed in straight corridors. In the past, 38W 2D was used (with mixed results) and sometimes 55W T5 circular lamps. Today the ADDISON achieves better results than both these light sources with just 21 watts, and it outperforms them in emergency mode too.

Let’s compare the same stairwell lit with 2 different NVC fittings;

the ADDISON 38W 2D and ADDIDSON LED The aim is to achieve 100 lux at floor level in normal operation and 1 lux minimum in emergency mode, with the highest possible uniformity and the lowest power consumption. Using 14 fittings in each case the results are as follows: STANDARD MODE

EMERGENCY MODE

Luminaire

Power (W)

Av Light Level (lm)

Uniformity (min/av)

Av Light Level (lm)

Uniformity (min/av)

ADDISON 38W 2D

532

101

0.57

5.6

0.44

ADDISON LED

296

158

1,27 0.58 0 lm

13

0.47

44% energy saving

>50% more light

Better uniformity

>130% more light

Better uniformity

Superior standard operation

NVC ADDISON 38W 2D fitting

NVC ADDISON LED fitting

In standard operation the LED fittings outperform the 38W 2D in light level and in uniformity.

Superior emergency operation In emergency mode, the LED fittings also outperform the 38W 2D in both average light level and uniformity.

These isolux diagrams illustrate the light levels being achieved on a flight of stairs in two lighting installations.

Each installation uses the same number of fittings, installed in the same position.

These diagrams show that our ADDISON LED fittings light stairwells much better than 38W 2D. If you are looking for 1:1 replacements of 2D, look to NVC.

+44 (0)121 457 6340 // www.nvcuk.com

AMENITY LIGHTING // 7

AMENITY LIGHTING

SPARTAN IP65 polycarbonate LED bulkhead fittings for commercial indoor and outdoor areas

OPTIONAL SNAP-ON PLAIN OR EYELID BEZELS WHITE OR BLACK AVAILABLE SEPARATELY

SCAN FOR DIGITAL COPY

APPLICATIONS

CONSTRUCTION

OPTIONS

- For commercial interior or exterior use in corridors, entrances, porches, steps and building perimeters.

- Polycarbonate base, available in black (suffix BK) or white (suffix WH) - Polycarbonate opal diffuser - Gasket between base and diffuser to ensure IP65 rating - Gear tray retained on strap for easy installation - Emergency maintained 3 hours version available as listed

DIMMING Dim-to-10% (corridor function) available on all variants. Suffix CF.

TECHNICAL DETAILS - 15W, 1,310 lm, 86 l.lm/c.W - CRI >80 - CCT 4000K - LEDs on metal core PCB

SENSORS Available with built in microwave sensor. Suffix MW. DIMMING & SENSOR A popular combination is corridor function & microwave sensor. Suffix CFMW. PE CELL Available with built in photoelectric cell for dusk to dawn operation.

Suffix PEC. TRIMS Optional bezel or eyelid trims that snap fit to fitting. As listed.

FITTING

ORDER CODE

DESCRIPTION

NSP15/BK/840

Spartan 15W LED IP65 Black Base 840

NSP15/BK/M3/840

Spartan 15W LED IP65 Black Base M3 840

NSP15/WH/840

Spartan 15W LED IP65 White Base 840

NSP15/WH/M3/840

Spartan 15W LED IP65 White Base M3 840

ACCESSORIES

BEZEL TRIM

8 // AMENITY LIGHTING

EYELID TRIM

NSP/BEZEL/WH

Spartan Bezel Trim White

NSP/BEZEL/BK

Spartan Bezel Trim Black

NSP/EYELID/WH

Spartan Eyelid Trim White

NSP/EYELID/BK

Spartan Eyelid Trim Black

+44 (0)121 457 6340 // www.nvcuk.com

AMENITY LIGHTING

SPARTAN...

is packed full of features With the eyelid bezel fitted it has the good looks for use around residential developments, but with its IP65 and IK10 ratings and screw-down cover it has the features to withstand some rough treatment on light commercial and public sector projects.

Tough polycarbonate base and screwTOUGH POLYCARBONATE BASE and screwdown diffuser ensures the IP65 is retained down diffuser ensures the IP65 is retained even after some hard knocks. even after some hard knocks.

SPARTAN can be installed like this without a bezel...

... or like this with a bezel

PLAIN OR EYELID BEZELS are available in black and white and can be fitted later if required.

DUSK/DAWN PHOTO-CELL AVAILABLE. To order, use suffix PEC. Perfect for use around building perimeters and entrances.

+44 (0)121 457 6340 // www.nvcuk.com

AMENITY LIGHTING // 9

AMENITY LIGHTING

BIG FINANCIAL SAVINGS WITH SENSORS The savings from installing NVC LED fittings can be bigger than you would expect.

LIKE-FOR-LIKE ELECTRICITY SAVINGS In a new-build, 18W LED can be used to replace 38W 2D with fewer fittings, achieving a higher light level and saving nearly 60% energy. Even bigger savings can be made by using sensors as well.

BIGGER SAVINGS WITH SENSORS

•

Micro-wave occupancy sensor with photo-cell When occupancy is detected the fitting will switch on, unless there is sufficient ambient light already available.

The sensor is adjustable for sensitivity (range), time-out and lux level.

•

Corridor function (Dim-to-10%) This is popular in combination with the micro-wave, but can also be used with an external sensor or time-switch.

When required the fitting goes to 100% output, but when no longer required (eg when the sensor is no longer detecting occupancy) it drops to 10%. Background lighting is therefore always present, creating a sense of safety and security.

All our amenity fittings for commercial use are available with any combination of the following options fitted: •

Emergency (3 hours maintained) These give a substantially higher output in emergency mode than the 2D fittings they typically replace, ensuring compliant lighting especially on stairs.

YOU MIGHT FIND THIS INTERESTING….

Micro-wave sensors – how they work Micro-wave sensors work like radar, using a phenomenon known as the “Doppler shift”. Each sensor emits and detects radiation. The radiation they emit is at a very lowlevel and is at a specific frequency; this bounces off solid objects and is detected by the same sensor that emitted it.

However, if the radiation bounces off a moving object (such as a person walking) the frequency is changed.

When this frequency change (known as the “Doppler shift”) is detected by the sensor it is an indication that the area is now occupied and that the lights should be switched on.

If the radiation bounces off a stationery object, such as a wall, the frequency of the radiation is unchanged.

Stationary object

Moving towards

Moving away

The frequency of the radiation emitted by the sensor is the same as the frequency of the radiation reflected off the stationery object. No change of frequency is detected, the sensor is not triggered.

The frequency of the radiation reflected off the body moving towards the sensor is higher than the frequency of the radiation emitted by the sensor. A frequency change (“Doppler shift”) is detected and the sensor is triggered.

The frequency of the radiation reflected off the body moving away from the sensor is lower than the frequency of the radiation emitted by the sensor. A frequency change (“Doppler shift”) is detected and the sensor is triggered.

Radiation emitted by sensor.

Radiation emitted by sensor.

Radiation reflected

.

Same frequency as radiation from sensor

10 // AMENITY LIGHTING

Radiation reflected ving towards sensor.

Higher frequency.

Radiation reflected ving away from sensor.

Lower frequency.

+44 (0)121 457 6340 // www.nvcuk.com

AMENITY LIGHTING

SAFETY & SECURITY WITH DIM-TO-10% CORRIDOR FUNCTION All our fittings with a micro-wave sensor can also be ordered with corridor function. This is a popular feature that means the lights are on at 10% all the time, and brighten to 100% when occupancy is detected.

This is widely used in corridors and stairwells where some constant background light gives people a feeling of well-being and security.

The adjustable time-out ensures that the lights stay at 100% while there is a possibility someone is still present.

Keeping the time out short maximises the energy savings, and with LEDs it does not increase maintenance costs.

LUX SWITCH-ON THRESHOLD

Light Output %

Extra energy saved by photo-cell Time out period

Time out period

Our micro-wave sensors are all equipped with a photocell as standard.

When the sensor is triggered by occupancy the light will only switch on if the ambient light level is beneath a pre-set threshold. This saves further energy by preventing the lights switching on, for example, at midday when plenty of natural light is present.

Note that if you choose Corridor Function (above) then the lux switch-on threshold that is a standard feature of our micro-wave sensors will not operate.

Lux switch-on threshold

Natural light level

Occupancy detected.

Lights on

Lights

Occupancy detected.

Lights r

Last occupancy detected

End of Occupancy Light-level Lights time-out detected. falls below switch Lights threshold, lights switch on Last occupancy r Last occupancy detected detected

HOW MUCH CAN BE SAVED WITH LEDS AND SENSORS? Consider a corridor in sheltered housing with 20 movements (people coming in and out) per day, with 4 x 28W 2D fittings installed.

Because of the risk of lamp failure these fittings are not controlled with a sensor and are running 24/7.

The total annual power consumption is therefore 28W/1,000 x 4 x 24 x 365 = 981KWhr/year.

SWITCH TO LED – SAVE 46% Switch to LED and the power consumption drops to 15W/1,000 x 4 x 24 x 365 = 526KWhr/year SWITCH TO LED WITH OCCUPANCY SENSING – SAVE 93% With LEDs and a micro-wave sensor on a time-out of, say, 10 minutes, the power consumption drops to 15W/1,000 x 4 x 3.33 x 365 = 73KWhr/year. In reality, the power consumption could be less than this if there is enough natural light present at any time to prevent the sensor switching the lights on.

+44 (0)121 457 6340 // www.nvcuk.com

SWITCH TO LED WITH OCCUPANCY SENSING AND CORRIDOR FUNCTION – SAVE 83% Corridor function increases the power consumption slightly when compared to just having LEDs with occupancy sensing. This is because even when occupancy is not detected the fitting is running at 10% (which consumes about 20% power). This extra (about 91KWhr/ year) brings the total to 164KWhr/year, but the residents have the benefit of a low level of background light at all times for a sense of reassurance and safety.

AMENITY LIGHTING // 11

AMENITY WEBPAGE

NVC Lighting Limited NVC Park 201, Hollymoor Way, Rubery, Birmingham B31 5HE UK T +44 (0)121 457 6340 F +44 (0)121 453 1325

Sales

Accounts

Technical

T +44 (0)121 457 6340

T +44 (0)121 457 6341

T +44 (0)121 457 6344

F +44 (0)121 453 1325

F +44 (0)121 457 6342

E technical@nvcuk.com

E sales@nvcuk.com

E accounts@nvcuk.com

12 // AMENITY LIGHTING

BRO/AMENITY/DEC2019