Garcia Headboard Instruction Sheet

Ok, let’s get rolling

This should be easy, just follow our instructions and you will be back to Netflix in no time.

Estimated time for assembly

45:00

What you need

• Some of your favorite bubbly or your preferred relaxant

• Use the packaging carton as a working surface to prevent product damage during assembly

• Phillips head screwdriver

• Drill (for wall mounting only)

• Pencil (for wall mounting only)

• 1/4” Drill bit (for non-drywall wall mounting only)

• 5/16” Drill bit (for drywall wall mounting only)

What’s included

Toll-free at 1-866-619-1004 Help@nathanjames.com Nathanjames.com/help

The goods

IMPORTANT

1. Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes.

2. Do not over tighten screws and bolts to avoid stripping.

3. Please use hand tools to assemble this product. Do not use power tools.

What’s included (cont.)

The goods (cont.)

Step 1: To attach to bed frame

Let’s get this thing fired up! First, slide two of the Horizontal Stretchers (E) into the Center Frame (B). Then slide the Right Side Frame (A) onto the ends of the Horizontal Stretchers (E). Once in place, secure using eight of the M6*20mm Bolts (1) and tighten using the provided Allen Key (6).

Then, repeat this process by sliding the remaining Horizontal Stretchers (E) and (F) onto the ends of the Center Frame (B). Next, slide the Left Side Frame (C) onto the ends of the Horizontal Stretchers (E) and (F). Once in place, secure using eight of the M6*20mm Bolts (1) and tighten using the provided Allen Key (6).

These assembly steps are for attaching the headboard to your existing bed frame. If you’d rather mount the headboard to your wall, skip ahead to page 13.

Step 2

Next, slide the Legs (D) into the bottom of the frame you built in Step 1. Secure by placing a Flat Washer (4) first, then a Spring Washer (3) on top of that, and finally a M6*20mm Bolt (1). Tighten using the provided Allen Key (6).

Step 3

Now it’s time to attach the Bed Frame Adapter Plates (G) to the Legs (D).

To secure these together, run the M6*55mm Bolts (2) through the back of the Legs (D) and in through the Bed Frame Adapter Plates (G).

Be sure you’ve placed the Flat Washer (4) and Spring Washer (3) before inserting the Bolt (2).

Then, secure on the other side using the M6*7mm Nuts (5). Again, make sure you place the Flat Washer and Spring Washer before securing the Nuts.

Tighten all to 75%.

Note: The slotted cutouts on the headboard legs and bed frame adapter plates allow for adjustability to be compatible with a variety of different bed frames.

Bed Frame Adapter Plate Notes: Adapter Plates can be used in 2 different orientations (shown to the right) to allow for maximum height adjustability. Slotted holes also allow for maximum compatibility with your bed frame.

Now it’s time to attach the headboard to your bed frame (not included). To secure the headboard, align the holes in your bed frame with the slotted holes in the Bed Frame Adapter Plates (G). Once aligned, slide the M6*20mm Bolts (1) into place.

Be sure to first place a Flat Washer (4), then a Spring Washer (3) before inserting the bolts.

Secure on the other side using the M6*7mm Nuts (5). Again, be sure to first place a Flat Washer and then a Spring Washer before inserting the Nuts.

Tighten all to 100%.

Bed frame NOT included

Lay the Upholstered Panel (H) over the top of the metal frame you’ve assembled.

With the strap buckles at the top, tighten the middle strap.

Step 6

Now, using the M6*20mm Bolts (1), secure the Upholstered Panel (H) to the Horizontal Stretcher (F). This will help keep everything in place before you tighten the rest of the straps.

Step 7

Finally, go ahead and begin to tighten all of the straps.

Helpful tip: Slowly tighten the straps in equal increments to one another for the best results; to have everything tightened equally and in alignment.

You did it! Now all that’s left to do is sit back, relax, and enjoy your new headboard!

x4

Step 1: To mount on wall

Let’s get this thing fired up! First, slide two of the Horizontal Stretchers (E) into the Center Frame (B). Then slide the Right Side Frame (A) onto the ends of the Horizontal Stretchers (E). Once in place, secure using eight of the M6*20mm Bolts (1) and tighten using the provided Allen Key (6).

Then, repeat this process by sliding the remaining Horizontal Stretchers (E) and (F) onto the ends of the Center Frame (B). Next, slide the Left Side Frame (C) onto the ends of the Horizontal Stretchers (E) and (F). Once in place, secure using eight of the M6*20mm Bolts (1) and tighten using the provided Allen Key (6).

These assembly steps are for mounting the headboard to your wall. If you’d rather attach the headboard to your existing bed frame, head back to page 6.

Step 2

Insert the Plastic End Caps (12) into the bottom of the Left Side Frame (C) and Right Side Frame (A).

Lay the assembled metal frame over the Upholstered Panel (H).

Be sure that the hardware is facing out.

With the strap buckles at the top, tighten the middle strap.

Step 4

Next, using the M6*20mm Bolts (1), secure the Upholstered Panel (H) to the Horizontal Stretcher (F). This will help keep everything in place before you tighten the rest of the straps.

Step 5

Finally, go ahead and begin to tighten all of the straps. Helpful tip: Slowly tighten the straps in equal increments to one another for the best results; to have everything tightened equally and in alignment.

x4

Step 6: Non-drywall application

First, determine the height at which you want your headboard to hang.

Next, using a drill and a 1/4” drill bit, drill two holes 1562mm apart from each other, making sure that they are level. Once your holes are drilled, insert the Non-Drywall Anchors (10) into the holes, then begin screwing the M4.2*32mm Screws (8) into the Non-Drywall Anchors.

Important Note: Take note of where the top of the keyholes on the Left Side Frame (C) and Right Side Frame (A) sit.

This will be the height that you will drill your holes at.

Important Note: Leave a 3mm gap between the wall and the back of the screw head to hang the headboard on in the following steps.

Step 6: Drywall application

First, determine the height at which you want your headboard to hang.

Next, using a drill and a 5/16” drill bit, drill two holes 1562mm apart from each other, making sure that they are level. Once your holes are drilled, insert the Drywall Anchors (9) into the holes, then begin screwing the M4.2*50mm Screws (11) into the Drywall Anchors.

9

Important Note: Take note of where the top of the keyholes on the Left Side Frame (C) and Right Side Frame (A) sit.

This will be the height that you will drill your holes at.

11

Important Note: Leave a 3mm gap between the wall and the back of the screw head to hang the headboard on in the following steps.

How to use drywall anchors

Step 7

Finally, using the keyholes on the back of the Left Side Frame (C) and Right Side Frame (A), mount your headboard to the wall.

Do this by fitting the head of the screws into the larger, bottom portion of the keyhole, then allow the headboard to slide down to rest on the protruding screws.

Helpful Tip: You can fine-tune how snug the headboard sits to the wall by screwing the screws in or out, as you see fit.

You did it! Now all that’s left to do is sit back, relax, and enjoy your new headboard!

No heartburn, when we handle the return

We really don’t want you to go through the hassle of re-packaging your item and sending it back, because let’s be honest…nobody has time for that.

Safety first, fun later

We want your product to last as long as possible, so we recommend that you tighten the screws 2 weeks after assembly and for added safety check the tightness of all screws every 2 months.

For proper care and treatment, please check our website at NathanJames.com/products

Safe use of this product starts with you.

Use this product responsibly with the primary concern for your safety. Follow assembly instructions carefully and inspect product upon receipt and each use.

Nathan James and its parent companies cannot be held legally responsible for any injuries or death resulted from failure to follow instructions or improper use of this product.

Do not modify the structure of this product in any way.

Our products have been tested to meet specific safety measures as they were originally intended to be sold. Any modifications will present the risk of creating significant safety issues which NJ will not be responsible for.

Proper use

DO NOT use for commercial purposes

DO NOT frolic on headboard

DO NOT use headboard as foot stool

DO NOT leave spilled liquid on headboard

DO NOT use headboard if damaged

DO NOT make temporary repairs

DO NOT use outdoors

We are only in business if you’re happy For starters, thanks for being you.

Toll-free at 1-866-619-1004

Help@nathanjames.com

NathanJames.com/help

We do our best to ensure your furniture arrives without any problems, but occasionally mistakes happen—as humans we are imperfect beings. In the event that a part is damaged or missing, we will be more than happy to provide you with replacement part(s) for free.

Warranty

This product comes with a lifetime warranty from the date of purchase. Please use your phone to scan the QR code to register your product or visit https://goo.gl/i9dk3q

Brooklyn Burdon

Founder, Nathan James

Did we do alright? Please spread the love!

If you are happy with your product, tell your friends and family about us or even better leave us a review online. Spreading the word gives us the opportunity to make more people happy and keep our prices low for your next purchase.