The goods

Important

1. Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes.

2. Do not over tighten screws and bolts to avoid stripping.

3. Please use hand tools to assemble this product. Do not use power tools.

Pre-Installation

• Read all instructions prior to beginning assembly.

• To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.

• Keep the receipt and these instructions for proof of purchase.

• Suggested Bulb: ST19 Vintage LED 60 Watt Equivalent | E26 Medium Base | Dimmable

• Fixture Max Wattage: 240W (60W per bulb)

Step 1

It’s as easy as it looks! Remove the screws from the non-fixed arm of the Fixture (1).

Step 2

Secure the non-fixed arm into the Fixture (1) by first sliding it into place and then using the screws that you removed in Step 1 to tighten.

Step 3

Decide your necessary fixture stem length to achieve your desired fixture height. Then, pass the cord through each of the necessary stem components for your desired fixture height.

4"Cord Stem Length:⑤

6"Cord Stem Length:④

10"Cord Stem Length:⑤+E+④

12"Cord Stem Length:②

16"Cord Stem Length:⑤+E+②

18"Cord Stem Length:④+E+②

22"Cord Stem Length:⑤+E+④+E+②

24"Cord Stem Length:③+②

30"Cord Stem Length:④+E+③+②

34"Cord Stem Length:⑤+E+④+E+③+② 12"

Helpful Tip: Braiding the cord first then rotating the tubes while passing the cord through will make things go a little more smoothly.

Thread the necessary stem components together to complete the connection between the Canopy (6) and the Fixture (1).

(Components will vary depending on your desired fixture height)

Step 4

Remove the Finial Nuts (C) from the Mounting Bracket (B).

Step 5

Mount the Mounting Bracket (B) onto your existing Electrical Box.

Note: Be sure that you are only making the connections to a 120V AC 60Hz circuit. If you do not have a pre-existing electrical box, we strongly advise using a certified electrician.

Step 6

You can adjust the orientation in which your fixture will face by using the adjustment screw in the middle of the Mounting Bracket (B).

First, slightly loosen the adjustment screw, then rotate the Mounting Bracket (B) to have the threaded posts oriented in your desired direction before re-tightening the adjustment screw to re-secure the Mounting Bracket (B) in place.

Step 7

Wrap the Ground Wire from the Fixture (1) around the grounding screw on the Mounting Bracket (B) & then secured by tightening the screw.

Use a Wire Nut (D) to join the ground wire from the Fixture (1) with the ground wire from the Electrical Box.

Use Wire Nuts to join the remaining matching colored wires (White to White, Black to Black). Once complete, tuck the excess wire into the Electrical Box.

White (Neutral)

Black (Hot)

Secure the fixture to the Mounting Bracket (B) on your pre-installed Electrical Box using the Finial Nuts (C) that you originally removed in Step 4.

To properly fasten the Finial Nuts (C), thread the posts in or out to adjust for proper threading length.

Step 10

Install your light bulbs (not included) and then adjust your shade and bulb assemblies to your desired orientation.

Suggested Bulb: ST19 LED 60 Watt Equivalent E26 Medium Base | Dimmable

Fixture Max Wattage: 240W (60W per bulb)

Bulb(not included)

Troubleshooting

Problem

The bulb will not light. The fuse blows or circuit breaker blows when the light is turned on.

270°

Possible Causes

The bulb is burned out.

The power is off.

The circuit breaker is off. There is an exposed wire.

Solutions

Replace the light bulb. Ensure the power supply is on. Ensure the circuit breaker is in the ON position. Discontinue use of the light. Contact a qualified electrician or reach out to our Customer Happiness team at help@nathanjames.com or 1-866-619-1004.