1/4
49 727
eduard
U-2/Po-2 S.A.
49 727
detail set for 1/48 ICM No. 48252 kit • sada detailů pro stavebnici 1/48 ICM No. 48252
APPLY EXPRESS MASK AND PAINT BEFORE GLUING POUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍM SYMETRICAL ASSEMBLY SYMETRICKÁ MONTÁŽ REMOVE ODSTRANIT
BEND OHNOUT
GRIND OBROUSIT
?
REPLACE NAHRADIT
DRILL HOLE VRTAT OTVOR
ORIGINAL KIT PARTS PŮVODNÍ DÍLY STAVEBNICE
OPTION VOLBA
1
COLORED ETCHED PARTS LEPTANÉ BAREVNÉ DÍLY
1
ETCHED PARTS LEPTANÉ NEBAREVNÉ DÍLY
1
ORIGINAL KIT PARTS PŮVODNÍ DÍLY STAVEBNICE
PARTS TO BE REMOVED DÍLY K ODSTRANĚNÍ
PHOTO-ETCHED PARTS LEPTANÉ DÍLY
A1
FILL TMELIT
4 pcs. 14
5 pcs. 22
E2-1
23
=
E2-2, E1-4, E1-3 A7
30
5 pcs. 23 5
A1
5 pcs. 23
26
E1-2
A7 A5
E1-6
11
C12
6
2 sets C37
1
C38
3 7
C16, C17, C18, C19, C5
7
2 4
2/4
49 727
12 C24
A11 B7
10
15
C27 A4
13
9
16
17
19
18
18
17
18
18
17
17
C14
C14 upper side
lower side
2 pcs. 8 20
2 pcs. 32
8
C15 31
C13 = A2
24 18
C40
18
3/4
49 727
21
wire wire 28
wire
28
wire upper side 17
28 28
29
C1 lower side
C1
21
wire lower side
wire
wire
28 28
25
wires
17
28 33
34 29
C40 C40 upper side
21
wire
27
28
A11 B4
B7 21
wire 28
© EDUARD M.A. 2015
www.eduard.com
Made in Czech Republic
4/4
49 727
PARTS WITH GLUE
DÍLY OPATŘENÉ LEPIDLEM
3. Do not touch the adhesive areas of the etched components. 1. Separate the etched components from their frames on the 3. Nesahejte na části dílů, na kterých je naneseno lepidlo. protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddělujte od rámečku na podkladovém papíře. Po oddělení je sejměte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za části, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will be permanently affixed when pressed onto its intended location, its location can be adjusted.
2. Do not inadvertently place etched componets on an 5. Díl lehce položte do pozice, ve které má být nalepen. unwanted surface. Attempts to remove will result in Upravte přesnou pozici a přimáčkněte. Díl dokonale přilne damage to your part. až po přimáčknutí, před přimáčknutím lze dílem opatrně 2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem přilepíte, při pokusu o odlepení dojde k poškození dílu.
manipulovat.