MATERIALS TO BE FURNISHED
CONTACT: LISA KOERNER PHONE: (217) 857 - 7193 EMAIL: lisak@stevensind.com
AND ADHESIVE
P.O. DRAWER 2128
616 E. WALTON AVENUE
DALTON, GA 30772-2128
CONTACT: MELANIE JOHNSON
PHONE: (800) 367 - 5504
EMAIL:A.JOHNSON@SHAWINC.COM
CONTACT: TODD HIELMAN
PHONE: (314)640 - 6521
EMAIL:TODD.HIELMAN@PATCRAFT.COM
ELEVATIONS
A204INTERIOR ELEVATIONS
A205INTERIOR ELEVATIONS
A206INTERIOR ELEVATIONS
A501DETAILS
A601DOOR SCHEDULE
A701WALL TYPES
03 Plumbing
P002PLUMBING GENERAL INFORMATION
P101SANITARY & VENT PIPING PLAN
P102PLUMBING DOMESTIC WATER FLOOR PLAN
P103DENTAL PIPING PLAN
P501PLUMBING DETAILS
P601PLUMBING SANITARY RISER DIAGRAM
P602PLUMBING DOMESTIC WATER RISER DIAGRAM
04 Mechanical
M001MECHANICAL GENERAL INFORMATION
M002MECHANICAL SCHEDULES
M101MECHANICAL FLOOR PLAN
M201MECHANICAL ROOF PLAN
M501MECHANICAL DETAILS
05 Electrical
E001ELECTRICAL SYMBOLS LEGEND AND GENERAL NOTES
E002ELECTRICAL SPECIFICATIONS
E003FLOOR PLAN POWER
E004FLOOR PLAN - LIGHTING
E005ELECTRICAL PANEL SCHEDULES AND RISER
E. TILE VENDOR:
ISC SURFACES 9245 DIELMAN INDUSTRIAL DRIVE ST. LOUIS, MO 63132 CONTACT: KEVIN PARDO PHONE: (636) 734 - 5080 EMAIL: kpardo@iscsurfaces.com
F. LIGHTING VENDOR:
CONTACT: MEGAN DONOGHUE PHONE: (860) 767 - 0110 x 232 EMAIL: mkd@sslighting.com
G. DENTAL EQUIPMENT:
PATTERSON DENTAL CONTACT: JOSEPH TECHAR PHONE: (651) 686 - 1600 EMAIL: joseph.techar@pattersondental.com
F. FIRE EXTINGUISHERS:
CONTACT: HD CONTACT SUPPLIES PHONE: (217) 540 - 5780 EMAIL: prosupplies@heartland.com
G. LOW VOLTAGE CABLING: HEARTLAND DENTAL CONTACT: JORDAN HULTS EMAIL: jhults@heartland.com
J. DIGITAL PANOREX AND X-RAY: CONTACT: ELIZSHA DARNELL PHONE: (217) 540 - 5658 EMAIL: edarnell@heartland.com
FINISH FLOOR LEGEND
1A3'-0"7'-0"SOLID C.W.WD21/A6012/A601STAIN-2
105 5A3'-0"7'-0"SOLID C.W.WD21/A6013/A601STAIN-6
107 1A3'-0"7'-0"SOLID C.W.WD21/A6012/A601STAIN-3
4A3'-0"7'-0"SOLID C.W.WD21/A6013/A601STAIN-3
4A2'-8"7'-0"SOLID C.W.WD21/A6012/A601STAIN-3
4A3'-0"7'-0"SOLID C.W.WD21/A6012/A601STAIN-3
4A2'-8"7'-0"SOLID C.W.WD21/A6012/A601STAIN-3
122 2A3'-0"7'-0"3/A6014/A601PAINT-5 123 1A3'-0"7'-0"SOLID C.W. HM1 1/A6012/A6013
1A3'-0"7'-0"SOLID C.W.WD21/A6012/A601STAIN-2
General Wall Type Notes:
5/8" GYPSUM BOARD
NOTE:
NOTE:
TO REMOTE SWITCH
ENTRY POINT FOR INTERCONNECTING CABLE WHEN REMOTELY MOUNTING OPERATOR CONTROL PANEL (SINGLE GANG BOX CAN BE USED) CABLE PROVIDED BY MANUFACTURER
4x4 POSTS (16" ON CENTER)
WALL MOUNTING PLATE PROVIDED BY MANUFACTURER
ENTRY POINT FOR INTERCONNECTING CABLE WHEN REMOTELY MOUNTING OPERATOR CONTROL PANEL (SINGLE GANG BOX CAN BE USED) CABLE PROVIDED BY MANUFACTURER
JUNCTION BOX POSITION FOR INTERCONNECTING CABLE WHEN REMOTELY MOUNTING OPERATOR CONTROL PANEL.
ELECTRICAL POWER ENTRY POINT
FLUSH MOUNTED SINGLE-GANG JUNCTION BOX
5/8" GYP. BOARD (BOTH SIDES) ATTACH DRYWALL TO ADDITIONAL FRAMING NOT 4X4 POSTS NOTE: X-RAY UNIT REQUIRES
COORDINATE WITH DENTAL
FOR SPANS LONGER THAN 9'-0" AND LESS THAN 12'-0", INSTALL 1/4" ALL THREAD ROD SUPPORTS AT THIRD SPAN LOCATION W/ 1" WASHER AND DOUBLE NUT. HANG FROM EXISTING JOISTS OR NEW UNISTRUT BETWEEN JOISTS (LOCATION OR CONFIGURATION VARIES). NO 2x6 COMPRESSION STUD REQUIRED.
5'-0" LONG 2x4 SECURELY FASTENED DIRECTLY TO STUDS WITH (8) #12 x 2 1/4" TEK SCREWS EACH END. MONITOR ARM MOUNTING PLATE. ANCHOR TO 2"x10" PER MANUFACTURERS RECOMMENDATIONS (6 FASTENERS MINIMUM).
VERTICAL EXTENSION OF MONITOR ARM
MONITOR ARM - SECTION
MONITOR ARM MOUNTING PLATE. ANCHOR TO 2"x10" PER MANUFACTURERS RECOMMENDATIONS (LOCATION VARIES).
FOR SPANS LONGER THAN 9'-0" AND LESS THAN 12'-0", INSTALL 1/4" ALL THREAD ROD SUPPORTS AT THIRD SPAN LOCATION W/ 1" WASHER AND DOUBLE NUT. HANG FROM EXISTING JOISTS OR NEW UNISTRUT BETWEEN JOISTS (LOCATION OR CONFIGURATION VARIES). NO 2x6 COMPRESSION STUD REQUIRED.
5'-0" LONG 2x4 SECURELY FASTENED DIRECTLY TO STUDS WITH (8) #12 x 2 1/4" TEK SCREWS EACH END
NOTE: 1. COORDINATE W/ EQUIPMENT MANUFACTURER REQUIREMENTS AND MEP DRAWINGS
FOR SPANS LESS THAN 9'-0", PROVIDE 2x6 COMPRESSION STUD. ANCHOR TO VERTICAL 2x8 w 1/4"x5" LAG SCREWS AT 12" O.C. PRE-DRILL HOLES PRIOR TO INSTALLATION.
2x4 (OFFSET FROM CENTER) VERTICAL SUPPORT AND 2x10 HORIZONTAL SPANNING WIDTH OF TREATMENT ROOM. FASTEN TOGETHER WITH 1/4"x5" LAG SCREWS AT 12" O.C. PRE-DRILL HOLES PRIOR TO INSTALLATION. TOP OF WALL BEYOND
SECURELY FASTEN BOTTOM 2x10 TO FIRE TREATED 2x4 WALL SUPPORT WITH (4) # 10x3" WOOD SCREWS AT EACH END.
FOR SPANS LESS THAN 9'-0", PROVIDE 2x6 COMPRESSION STUD. ANCHOR TO VERTICAL 2x8 W/ 1/4"x5" LAG SCREWS AT 12" O.C. PREDRILL HOLES PRIOR TO INSTALLATION.
2x4 (OFFSET FROM CENTER) VERTICAL SUPPORT AND 2x10 HORIZONTAL SPANNING WIDTH OF TREATMENT ROOM. FASTEN TOGETHER WITH 1/4"x5" LAG SCREWS AT 12" O.C. PRE-DRILL HOLES PRIOR TO INSTALLATION.