(INT) 2022 Concrete Placement Equipment – Husqvarna Construction

SMARTER SOLUTIONS TO FINISH CONCRETE SURFACES AND FLOORS CONCRETE PLACEMENT EQUIPMENT BY HUSQVARNA FOR A BETTER WAY OF WORKING

TAKING YOUR CONCRETE BUSINESS TO FIRST CLASS

Every concrete construction starts with a solid foundation. We provide you with the tools and solutions to create just that. We rely on three basic principles: highperforming and well-designed quality equipment, a clear focus on the operator’s efficiency, and a service and support network to back you up in any event.

That is how we enable you to achieve a better way of working.

HIGH PERFORMANCE PRODUCTS

FOCUS ON THE OPERATOR’S EFFICIENCY

Husqvarna’s concrete equipment is developed for maximum productivity, performance and reliability.

Every little detail within – from the hard-wearing vibrator heads to the reliable trowel motors – is designed to get the job done with maximum uptime and minimum service required.

The operator’s efficiency is the key to high production rates and a high-quality job result. By designing the products for easy handling, reliable operation and best possible safety, we enable the operator to stay productive the whole working day.

SUPPORT AND SERVICE YOU CAN COUNT ON Our machines are built to provide maximum uptime, and so is our extensive service network. We are never far away when you need to consult a Husqvarna-trained technician or have any service or spare parts delivered.

Visit our website www.husqvarnacp.com to find your nearest Husqvarna Service Center or authorized servicing dealer for Husqvarna Construction Products.

COVERING ALL STEPS OF THE JOB Husqvarna offers a wide range of equipment that covers every step of the concrete placing and finishing process – including vibration, levelling, finishing and ultra-early entry sawing of poured concrete surfaces and floors.

CONCRETE VIBRATION Vibration helps remove the air voids from concrete as it is being poured or immediately afterwards. By removing the air, the density of the concrete increases, making the concrete stronger. Depending on the depth and slump of the concrete, a high density concrete can be achieved by using an internal vibrator or a vibrating screed.

4

CONTRACTION JOINT SAWING As a concrete slab hydrates and begins to set, it develops internal stresses that cause it to crack. Sawing straight, shallow joints in the freshly poured concrete prevents random cracks appearing. With the patented Husqvarna Soff-Cut Ultra Early Entry™ dry-cutting system, contraction joints can be sawn into the green zone within two hours of pouring.

CONCRETE SURFACING

CONCRETE LEVELLING

Once the concrete reaches a plastic state, power trowels are used for floating and trowelling to remove irregularities from the screeded surface. During this process, the concrete surface is compacted and sealed which makes the floor even more durable. The intention is to obtain a smoother and more even concrete floor, and also to reduce the concrete dust created from wear.

In most cases, the concrete needs to be levelled to create an even surface. One or two screeding passes with a vibrating screed alone is often enough on single-reinforced slabs. If an already installed concrete floor is to be covered by a new concrete layer, surface vibration is an excellent method for obtaining an high level of adhesion between the two concrete constructions.

5

In our high frequency electric vibrators, the vibrations are produced by an electric motor rotating inside the vibrator head. This design allows the vibrator head to be completely sealed, which also means that very little maintenance is required.

HUSQVARNA SMART SERIES | HIGH FREQUENCY ELECTRIC VIBRATORS

FOR INTENSE WORK AND MAXIMUM OUTPUT Husqvarna Smart is a powerful system with an integrated, intelligent frequency converter developed for intense professional use. Any regular, single-phase wall socket with the appropriate voltage will suffice as power source.

Just plug in and start working straight away.

The high centrifugal force, stable speed and high amplitude contribute to efficient concrete vibration with fewer dips. 15 metres of cable + 5 metres of hose enable exceptional reach around the worksite. The Smart-E

6

version is ideal for flooring applications and features a pistol grip handle that reduces hand /arm vibration.

The integrated frequency converter is well protected against shock, overload and overheating. All electronics are built into the streamlined aluminum box with one push ON/OFF button. A LED indicator shows the working status of the vibrator and alerts the operator if something needs to be checked.

TUBE SIZES

SMART-E

SMART

All measurements are in mm. L = Length Ø = Diameter

40

48

56

Ø 40 48 56 L 320 350 380

65

E 40 E 48

65 410

40 48 56 320 350 380

WORK FAST

EASY HANDLING

A frequency of 12000 vpm across the Smart series range ensures high centrifugal force, stable speed and high amplitude – excellent concrete vibration with fewer operator dips.

With 15 metres of cable and 5–10 metres of hose, Husqvarna Smart gives you exceptional reach around the worksite.

E 56

RADIUS OF ACTION Up to: 12× diameter

PLUG AND WORK With built-in frequency converters, a regular singlephase wall socket is all you need to power up and start working.

ENERGY & DRIVE UNIT 230 V

ERGONOMIC MOTOR-IN-HEAD DESIGN

CONSISTENCY High to low slump

ACCESSORIES

Having the motor in the head keeps vibrations where they belong – in the concrete rather than in the operator’s hands and arms.

HEALTHIER WORKPLACES

PART NUMBERS

Husqvarna Smart and AX pokers Elastomer end cap ∅ 40 595 15 67-01 Elastomer end cap ∅ 48 595 15 68-01 Elastomer end cap ∅ 56 595 02 96-01 Elastomer end cap ∅ 65 595 45 09-01

SMART VIBRATORS

65 – 5 M

Using electricity instead of petrol means no fumes and less noise. Pistol grip handles reduce hand / arm vibrations, and the built-in converter is well protected against shock, overload and overheating.

Elastomer end caps

56 – 10 M

56 – 8 M

56 – 5 M

48 – 10 M

48 – 8 M

48 – 5 M

40 – 5 M

Tube diameter, mm

65

56

56

56

48

48

48

40

Frequency, vpm

12000

12000

12000

12000

12000

12000

12000

12000

Voltage, V

230

230

230

230

230

230

230

230

Frequency, Hz

50/60

50/60

50/60

50/60

50/60

50/60

50/60

50/60

Amperage, A

10

6.4

6.4

6.4

4.5

4.5

4.5

2.5

Hose length, m

5

10

8

5

10

8

5

5

Cable length, m

15

15

15

15

15

15

15

15

Sound power, LW dB(A)

99

94

94

94

91

91

91

86

Vibration value, m/s²

2.47

2.47

2.47

2.47

5.87

5.87

5.87

4.62

967 93 88-01

967 85 60-05

967 85 60-02

967 85 60-04

967 85 59-02

967 85 59-03

967 85 59-05

967 85 58-03

SMART-E VIBRATORS

E 56

E 48

E 40

Tube diameter, mm

56

48

40

Frequency, vpm

12000

12000

12000

Voltage, V

230

230

230

Frequency, Hz

50/60

50/60

50/60

Amperage, A

6.4

4.5

2.5

Hose length, m

0.5

0.5

0.5

Cable length, m

15

15

15

Total weight, kg

14.8

13.6

12

Sound power, LW dB(A)

94

91

86

Vibration value, m/s²

0.52

0.52

0.52

PART NUMBERS

The Smart-E version features a pistol grip handle that reduces hand/arm vibration.

PART NUMBERS 967 94 03-03 967 94 02-04 967 85 58-04

7

HUSQVARNA AX/VIBRASTAR SERIES | HIGH FREQUENCY ELECTRIC VIBRATORS

FOR LARGE SLABS AND LONG SHIFTS Husqvarna AX vibrators are light and maneuverable, easy to use and powered for the toughest jobs. These vibrators are ideal when many are to be used in parallel, since one frequency converter can run up to four vibrators simultaneously. There’s an AX vibrator for almost any application. From high to low slump concrete, from thin beams to extensive foundations.

The electric motor-in-head design provides the vibrator head with outstanding performance, high power and stable speed. Rapid acceleration helps minimize air voids within the concrete and transports them to the surface. An easyto-operate, robust aluminum toggle switch is standard.

8

Husqvarna Vibrastar are cost-effective vibrators for less challenging applications. The reliable and sturdy vibrators are designed for medium to high slump concrete. The easyto-use aluminium switchbox offers one-hand operation and reduced hand/arm vibration. That means you’ll be able to work longer without getting tired.

The dual fiber layers in the hose, and oil lubricated bearings in the vibrator, provide improved durability without the need for periodic maintenance. As for maintenance, our service-friendly design makes it really easy for you to replace bearings.

WIDE RANGE Handles all type of concrete, from low to high slump.

HUSQVARNA AX

AX

TUBE SIZES All measurements are in mm. L = Length Ø = Diameter

AX 36 AX 40 AX 48 AX 56 AX 65 AX 90

Ø 36 40 48 56 65 L 322 320 350 380 410

90 566

RADIUS OF ACTION Up to: 10× diameter.

ENERGY & DRIVE UNIT CF 42 V

LONG LIFE Hoses and cables feature excellent resistance, traction and bending properties.

ENERGY EFFICIENT

TUBE SIZES

Low power consumption.

All measurements are in mm. L = Length Ø = Diameter

HUSQVARNA VIBRASTAR

EXTENSION CORD Available in 5, 10, 15 and 20 metres

FLEXIBLE MATERIALS

Features roller bearings (except AX 36 and AX 40) and induction hardened steel for extended lifetime.

VIBRASTAR

CONSISTENCY High to low slump

40

50

60

Ø 40 50 60 L 255 284 330

RADIUS OF ACTION Up to: 8× diameter

ERGONOMIC DESIGN

UPTIME

Low hand and arm vibration value due to the double ball bearing with eccentric in the middle.

Vibrastar is a reliable and tough vibrator, designed for medium to high slump concrete.

ENERGY & DRIVE UNIT CF 42 V CONSISTENCY High to medium slump EXTENSION CORD Available in 5, 10, 15 and 20 metres.

9

HUSQVARNA CF POWER UNITS FOR AX/VIBRASTAR

POWER AVAILABLE ANYTIME, ANYWHERE Husqvarna AX and Vibrastar are 42 Volt/200 Hz high-frequency electric vibrators, powered by either a Husqvarna CF frequency converter or generator, available with 1, 2 or 4 outlets.

STABLE OUTPUT

HUSQVARNA CF CONVERTERS

Connected to the main socket, 1-phase or 3-phase depending on model, all of these CF converters deliver stable output.

OVERHEAT PROTECTION All CF converter models come with built-in overheat protection.

RESET BUTTON FOR SAFETY In case of a voltage drop, a CF converter does not restart until the reset button is pushed.

AX VIBRATORS

AX 90

AX 65

AX 56 – 10 M AX 56 – 8 M

AX 56 – 5 M

AX 48 – 10 M AX 48 – 8 M

AX 48 – 5 M

AX 40

AX 36

Tube diameter, mm

90

65

56

56

56

48

48

48

40

38

Frequency, vpm

6000

12000

12000

12000

12000

12000

12000

12000

12000

12000

Voltage, V (3-phase)

42

42

42

42

42

42

42

42

42

42

Frequency, Hz

200

200

200

200

200

200

200

200

200

200

Amperage, A

21

19

11.7

11.7

11.7

10

10

10

4.5

6.2

Hose length, m

3

5

10

8

5

10

8

5

5

5

Cable length, m

10

10

10

10

10

10

10

10

10

10

Total weight, kg

26.6

18.8

20.5

18.5

16.1

17.4

15.4

15.1

13.2

13.1

Sound power, LW dB(A)

76

79

79

79

79

76

76

76

78

70

Vibration value, m/s²

5.06

4.62

3.66

3.66

3.66

3.53

3.53

3.53

3.81

3.81

PART NUMBERS 967 94 00-01 967 85 83-01 967 85 82-03 967 85 82-02 967 85 82-01 967 85 81-03 967 85 81-02 967 85 81-01 967 85 80-01 967 85 79-01

10

VIBRASTAR

60

50

40

FREQUENCY CONVERTERS

CF 67T

CF 25

CF 11

Tube diameter, mm

60

50

40

Output power, kVA

4.7

1.8

0.8

Frequency, vpm

12000

12000

12000

Intensity at 42 V, A Number of phases (primary voltage) Number of outlets

67

25

11

Voltage, V (3-phase)

42

42

42

Frequency, Hz

200

200

200

Amperage, A

11

8

4

Hose length, m

5

5

5

Cable length, m

10

10

10

Total weight, kg

15

13

8.4

Sound power, LW dB(A)

84

76

75

Vibration value, m/s²

3.23

3.28

1.8

967 93 81-03

967 93 81-02

967 93 81-01

PART NUMBERS

ACCESSORIES AX/VIBRASTAR 596 57 02-01

Extension cable, 5 m, 3G4 mm²

596 57 02-02

Extension cable, 10 m, 3G4 mm²

596 57 02-03

Extension cable, 15 m, 3G4 mm²

596 57 02-04

Extension cable, 20m, 3G6 mm²

3

1 or 3

1

4

2

1

Weight, kg

70

31

18

Protection index

IP55

IP55

IP55

Noise level, dB(A)

85

80

76

Transport wheels

standard

optional

—

PART NUMBERS 230 V-1-50 Hz 400 V-3-50 Hz

—

967 93 87-01

967 93 79-01

967 93 82-01

967 91 34-02

—

400 V-3-50 Hz CI4P*

967 93 82-02

—

—

380 V-3-60 Hz CI4P*

967 93 82-03

—

—

Transport trolley

—

596 40 08-01

—

* CI4P = Four outlets with motor breakers that protect the external vibrators against high ampere consumption.

ACCESSORIES AX 594 78 61-01

Elastomer end cap, ∅ 36

595 15 67-01

Elastomer end cap, ∅ 40

595 15 68-01

Elastomer end cap, ∅ 48

595 02 96-01

Elastomer end cap, ∅ 56

595 45 09-01

Elastomer end cap, ∅ 65

11

HUSQVARNA AME SERIES | MODULAR FLEX-SHAFT VIBRATORS

VERSATILE VIBRATORS FOR SMALL TO MID-SIZE JOBS Husqvarna AME 1600 and AME 600 are versatile systems designed for occasional concrete pouring applications.

Just plug into a regular wall socket to let the combination of high frequency electric power and mechanic force do the job for you.

The low-weight portable electric drive units and numerous configurations make these systems ideal when pouring floors, slabs, beams, columns and pillars in housing.

12

Husqvarna AME 600 is developed for thin layers and low slumps, while Husqvarna AME 1600 can handle bigger challenges.

All shafts and vibrators in these systems are equipped with quick couplings for ease of assembly. Instant speed and power from the drive unit provides rapid acceleration contributing to the outstanding performance.

OPERATOR FRIENDLY Rubber padded handle for reduced hand/arm vibration (below 2.5 m/s²).

HA

TUBE SIZES All measurements are in mm. L = Length Ø = Diameter

LOW WEIGHT AME 600 weighs in at only 1.9 kg, making it Husqvarna’s lightest vibrator. Perfect for small areas.

HUSQVARNA AME 600

RADIUS OF ACTION, HA Up to: 8× diameter

ENERGY & DRIVE UNIT AME 600 HA 25 HA 35

Ø 25 35 L 295 330

CONSISTENCY High to medium slump FLEXIBLE SHAFT Available in 1, 2, 3 metres, see table on this page

DRIVE UNITS

AME 600

Voltage, V (1-phase)

230

Frequency, Hz

50/60

Power, kW

0.6

Rated consumption, A

2.7

Frequency, rpm

3000

Weight, kg

1.9

Vibration value, m/s²

1.72

PART NUMBERS 967 93 31-01

VIBRATORS (HIGH FREQUENCY) Tube diameter, mm

HA 35/3

HA 35/2

HA 35/1

HA 25/3

HA 25/2

HA 25/1

36

36

36

26

26

26

Frequency, vpm

12000

12000

12000

12000

12000

12000

Total weight, kg

7.6

6

4.4

5.2

4.0

2.8

1.7

1.7

1.7

1.7

1.7

967 93 84-02

967 93 84-01

967 93 83-03

967 93 83-02

967 93 83-01

Vibration value, m/s² 1.7 PART NUMBERS

AME 1600

Voltage, V (1-phase)

230

Frequency, Hz

50/60

Power, kW

1.6

Frequency, vpm

12000

Weight, kg

6.1

Vibration value, m/s²

4.16

Protection level

IP44

TUBE SIZES All measurements are in mm. L = Length Ø = Diameter

RADIUS OF ACTION, AT Up to: 10× diameter

PART NUMBERS 967 93 36-01

FLEXIBLE SHAFTS SUPERFLEX Length, m Total weight, kg

ENERGY & DRIVE UNIT AME 1600

40

30

20

10

4

3

2

1

7.3

5.6

3.8

2.4

PART NUMBERS 967 85 95-05 967 85 95-04 967 85 95-03 967 85 95-01

VIBRATOR HEADS

AT 59

AT 49

AT 39

AT 29

Tube diameter, mm

59

49

39

29

Frequency, vpm

12000

12000

12000

12000

Total weight, kg

3.9

2.7

2.1

1.3

PART NUMBERS

Ø L

AT 29 AT 39 AT 49

AT 59

29 39 332 315

59 306

49 311

CONSISTENCY High to low slump FLEXIBLE SHAFT Available in 1, 2, 3, 4 metres

HUSQVARNA AME 1600

DRIVE UNITS

AT

967 93 84-03

LONG LIFE AT 59 features oil lubrication which contributes to long life and keeps life cycle costs down.

DURABLE Foam filter helps protect the drive unit from dust.

967 85 96-04 967 85 96-03 967 85 96-02 967 85 96-01

13

In our mechanical vibrators, the vibrations are produced by a pendulum rotating inside the vibrator head. A flexible, rotating driveshaft transfers the power mechanically to the pendulum from the power source through the hose. The driveshaft can be powered by a petrol engine or electric motor.

Mechanical vibrators are sturdy and reliable, given the proper maintenance.

HUSQVARNA AA AND AZ SERIES | MECHANICAL VIBRATORS

MODERN CLASSICS YOU CAN TRUST These classic mechanical pendulum vibrators have been refined over the years. Constant high vibration and simple design make them reliable, effective and offer great economical value. Both AA and AZ feature smart couplings with flexible shafts. These systems are powered by modern petrol or diesel drive units with low fuel consumption.

The conical shape of the pendulum raceway increases the friction area within the vibrator head to keep speed

14

up and prevent rpm losses. To reduce hand /arm vibrations and increase wear resistance, hose stiffener are used on large diameters.

The use of induction-hardened magnesium steel alloy in the major wearing parts and steel reinforcement in the rubber hose contribute to a long service life. The simple design makes maintenance easy and inexpensive.

Service kits are available.

To reduce weight, the pendulum shaft in the AZ model turns directly inside the end-cap.

AZ

ENERGY & DRIVE UNIT AMD 3000 and AMG 3200

Ø L

AA 27 AA 37 AA 47 AA 67 AA 77

AZ 26 AZ 36 AZ 46 AZ 56

25 39 49 63 75 334 366 420 500 510

25 35 45 55 295 330 375 390

RADIUS OF ACTION AA up to: 10× diameter

HUSQVARNA AMG 3200 /AA 47

LIGHTER

All measurements are in mm. L = Length Ø = Diameter

AA

TUBE SIZES

TOUGH High induction hardened steel parts.

CONSISTENCY AA: Low to high slump AZ: Medium to high slump

AZ up to: 8× diameter

USER FRIENDLY

HUSQVARNA AMD 3000 /AA 67

AZ comes with a 4,8 metre hose.

RELIABILITY AA 47, AA 67, AA 77 comes with a hose stiffener near the vibrating element for extended life time.

REACH IS KING AA comes with a 6 metre hose.

POWER Longer pendulum shaft turning in a bearing conical raceway extends lifetime with higher centrifugal force involved.

AA VIBRATORS

AZ VIBRATORS

MECHANICAL VIBRATORS (PENDULUM TYPE) Tube diameter, mm

75

63

50

39

25

55

45

35

25

Frequency, vpm

9200

10500

11200

12000

12000

11300

12000

12000

12000

AA 77

AA 67

AA 47

AA 37

AA 27

AZ 56

AZ 46

AZ 36

AZ 26

Hose length, m

6

6

6

6

6

4.8

4.8

4.8

4.8

Total weight, kg

29

25

23

19

10

17

16

11.6

9.5

Sound power, LW dB(A)

75.7

75.8

73

68

69

90.0

87.4

82.0

77.5

Vibration value, m/s²

3.16

2.66

3.52

1.56

2.46

8.27

2.42

5.22

2.00

PART NUMBERS Standard coupling

967 85 77-01 967 85 76-01 967 85 75-01 967 85 74-01 967 85 73-01 967 93 91-01 967 93 80-01 967 93 90-01 967 93 89-01

HUSQVARNA AM DRIVE UNITS FOR AA AND AZ VIBRATORS The AA and AZ systems are powered by petrol or diesel drive units with low fuel consumption. They are motorized with renowned engines from Lombardini (diesel) and Honda (petrol) to ensure reliable operation in all conditions.

DRIVE UNITS

AMG 3200

AMD 3000*

Fuel

Petrol

Diesel

Power, hp

4.8

4.1

Speed, rpm

2900

2900

Weight, kg

30

46

Engine brand

Honda

Lombardini

Sound power, LW dB(A)

103.8

79

967 85 72-01

967 92 86-01

PART NUMBERS Standard coupling

AMG 3200

AMD 3000

* Not availabe for EU in 2022.

15

HUSQVARNA AY SERIES | PNEUMATIC VIBRATORS

POWERED BY COMPRESSED AIR In our AY pneumatic vibrators, the vibrations are produced by a rotor inside the vibrator head. The rotor is driven by compressed air which is transferred trough the hose from a compressor. Pneumatic vibrators are powerful, economic, sturdy and reliable, given the proper maintenance.

Modern compressors are economic and quiet and can run several vibrators simultaneously. Husqvarna offers a wide range of pneumatic vibrators to match

16

your compressor. This is an efficient solution if an air compressor is already available at the work site.

Husqvarna AY vibrators are ideal for vibrating walls and columns since the air-cooled design doesn’t depend on the concrete to keep the temperature down. The easy-to-twist ball stop handle helps to avoid air leakage and power losses. The absence of moving parts in the hose means hand/arm vibrations are reduced. The AY 157 is equipped with two handles for easier handling.

TUBE SIZES

AY

All measurements are in mm. L = Length Ø = Diameter

WIDE VARIETY OF APPLICATIONS AY 27 AY 37 AY 47 AY 57 AY 67 AY 77 AY 87 AY 107

Ø 26 36 47 56 67 77 87 L 254 267 316 344 365 398 410

High centrifugal force and acceleration makes pneumatic vibrators ideal for everything from concrete lab tests to dam construction projects.

AY 157

108 415

155 420

RADIUS OF ACTION Up to: 12× diameter

EASY HANDLING The easy-to-twist ball stop handle with on-off function helps avoid air leakage and power losses.

ENERGY & DRIVE UNIT Compressor

CONSISTENCY Low to high slump

USER FRIENDLY The AY 157 is equipped with two handles.

DURABLE The absence of moving parts in the hose means less hand/arm vibration and extended service life.

STAYS COOL AY vibrators are excellent for walls and columns because they’re air-cooled and don’t depend on the concrete to keep the temperature down.

PNEUMATIC VIBRATORS

AY 157

AY 107

AY 87

AY 77

AY 67

AY 57

AY 47

AY 37

AY 27

Tube diameter, mm

155

108

87

77

67

56

47

36

26

Air consumption, m³/min

2.7

1.9

1.6

1.3

1

1

0.7

0.46

0.36

Frequency, vpm

12000

15000

15900

16000

17500

18000

18000

19000

21000

Hose length, m

0.8

1.5

1.5

4

4

4

4

4

4

Total weight, kg

28

23

18

17

11

10

7

5

4

Sound power, LW dB(A)

92.4

96.3

94.0

98

94

95

95.8

89.2

84.5

Vibration value, m/s²

12.29

2.91

1.95

2.38

2.10

2.13

2.39

1.02

0.51

PART NUMBERS 4 m hose

967 95 14-01 967 93 99-01 967 93 98-01 — — — — — — — — — 967 93 97-02 967 93 96-02 967 93 95-02 967 93 94-02 967 93 93-02 967 93 92-02

17

Suitable for all concrete mixes on civil engineering sites and in precast factories. A single moving part facilitates seamless operation. No regular maintenance required. Available with quick-release brackets.

HUSQVARNA EP AND ER SERIES | EXTERNAL VIBRATORS

MAKE SURE TO GET GOOD EXTERNAL VIBRATIONS Husqvarna offers a wide range of external vibrators – from high speed pneumatic to normal frequency electric – all with adjustable centrifugal force. To improve flexibility and cost-effectiveness, ER 207 B, ER 407 B and ER 507 B vibrators are mounted on quick-release brackets. This

18

makes them easier to move, so fewer units are required.

High-quality components and materials help keep life cycle and maintenance costs down.

ER ELECTRIC VIBRATORS

HUSQVARNA EXTERNAL VIBRATORS

The ER series provides high centrifugal force. To improve flexibility and cost-effectiveness, ER 207 B, ER 407 B and ER 507 B vibrators are mounted on quick-release brackets. This makes them easier to move, so fewer units are required

Images includes ER-7 series, bracket and CF 67T CI4P

ADJUSTABLE CENTRIFUGAL FORCE You have the flexibility to adjust as you like to suit the job at hand.

EP PNEUMATIC VIBRATORS The EP series is suitable for all concrete mixes on civil engineering sites and in precast factories. A single moving part facilitates seamless operation. Integrated noise reduction makes these vibrators very quiet. Also features quick-release brackets.

HIGH SPEED PNEUMATIC VIBRATORS Speed, rpm

QUICK-RELEASE BRACKETS Quick-release brackets allow you to secure the vibrator and increase flexibility during use.

EP 601 B

E P371 B

8800

EP 271 B

9350

EP 121 B

9350

9000

Max. centrifugal force, N

31500

26800

10350

8100

Air consumption, l/min

1400

1400

1200

1200

Weight, kg

18

16.5

10

9.5

Bracket attachment

VT4

VT4

VT2

VT2

PART NUMBERS Bracket

967 97 00-01

967 96 99-01

967 96 98-01

967 96 97-01

597 15 71-01

597 15 71-01

597 15 72-01

597 15 72-01

HIGH SPEED ELECTRIC VIBRATORS

ER 507 B

ER 407 B

ER 207 B

Speed, rpm

6000

6000

6000

Max. centrifugal force, N

16000

11000

7400

Voltage, Hz

42V-3-200

42V-3-200

42V-3-200

Intensity, A

23.5

16.5

12.5

Weight, kg

23.2

15.5

10.5

Bracket attachment

VT4

VT4

VT2

967 97 32-01

967 96 94-01

967 97 26-01

597 15 71-01

597 15 71-01

597 15 72-01

PART NUMBERS Bracket

NORMAL SPEED ELECTRIC VIBRATORS

ER 705

ER 605

ER 505

ER 405

ER 305

ER 205

ER 105

Speed, rpm

3000

3000

3000

3000

3000

3000

3000

Max. centrifugal force, N

16000

12000

7400

6000

3000

1400

500

Intensity at 230V/400V, A

4.20/2.50

3.30/1.90

2.30/1.33

1.80/1.09

0.68/0.39

0.30/0.18

0.16/0.09

Weight, kg

46.80

44.60

22.00

20.00

11.00

4.30

2.70

967 96 96-01

967 97 31-01

967 97 30-01

967 97 29-01

967 96 95-01

967 97 28-01

967 97 27-01

—

—

597 26 75-01

597 26 75-01

594 36 77-01

—

—

PART NUMBERS Bracket

19

HUSQVARNA BV SERIES | WALK-BEHIND SCREEDS

EASY SCREEDING – NOW AVAILABLE WITH BATTERY Husqvarna vibratory wet screeds are reliable tools for efficient leveling with excellent results. The popular BV 30 screed is now available with battery power – the ecosensible choice paired with improved ergonomics, easier operation and low maintenance. Enjoy efficient, sustainable concrete finishing today with the BV 30i screed from Husqvarna.

The vibratory wet screeds can be used directly on thin slabs up to 100 mm (BV 30) and 150 mm

20

(BV 20 G) without using internal vibrators if the edges are vibrated beforehand. The design of the lightweight, non-corrosive aluminum/ magnesium profiles is optimized for perfect end result and easy cleaning with no open sections for wet concrete to enter. The drive units have variable speed (vpm) and some models e.g. the BV 30i also offers the possibility to adjust the settings of the eccentric weights - for perfect results in stiff and wet concrete.

HUSQVARNA BV 20 G

LONG REACH

BV 20 G

The standard inter-connectable handle makes it possible to work from outside the slab with a total reach of 3.6 metres.

The optional extra handle gives you a total reach of 5.4 metres.

BV 30

BV 30i

BV 20 H

50 mm

100 mm

IN-DEPTH ACTION On thin slabs up to 100 mm (BV 30/BV30i) and 150 mm (BV 20 G) no vibration is needed beforehand.

150 mm

The lightweight design and articulated handle make it easy to operate.

SPEED ADJUSTMENT All of our models, except the manually operated BV 20 H, comes with speed adjustment possibilities.

QUALITY THAT LASTS There’s little need for maintenance thanks to lightweight non-corrosive aluminium profiles and high-quality drive units.

HUSQVARNA BV 30

HUSQVARNA BV 30i

ALWAYS NIMBLE

PROFESSIONAL RESULTS, EVERY TIME The rigid bottom plate features a V-shaped profile that drives excess concrete backwards, which refills operator foot marks.

WALK-BEHIND SCREEDS

BV 20 G

Working width, m

2.0

BV 20 H 2.0

Weight operating, kg

16.6

7.5

Length handle, m

1.8 + 1.8

1.8 + 1.8

Energy

Petrol

Manual

WALK-BEHIND SCREED

BV 30

BV 30i**

Weight, drive unit, kg

14

11.5**

Motor*

4-stroke Honda GX35

Brushless Husqvarna motor

Nominal voltage, V

—

36

Recommended batteries

—

BLi 200 / BLi 300

Run time (BLi 300), min

—

Up to 70

Power, kW

1.6 at 7000 rpm

0.8

Vibration frequency, rpm

2000–7400

3500-7500

Centrifugal force, N

3460

1600 (at 7500 rpm)

Vibration value, m/s²

3.25

—

Noise level, dB(A)

108

—

967 85 63-01

967 97 38-01

Motor/engine

4-stroke Honda GX 25

—

Power, kW

0.72 at 7000 rpm

—

Vibration frequency, rpm

4000–7000

—

Centrifugal force, N

1100

—

Vibration value, m/s²

3.2

—

Noise level, dB(A)

91

—

PART NUMBERS Without blade

967 85 62-01

967 85 61-01

* The drive unit is delivered without screed blades (ordered separately). ** Without battery and equipment.

595 02 95-01

595 02 95-01

PART NUMBERS Extension handle

BV 30I: Batteries and chargers can be purchased separately or as a kit: 967 97 38-03 (BV 30i + 2 × BLi 300 + QC 500)

BV 30 / BV 30i SCREED BLADE

4.2 M

3.6 M

3.0 M

2.4 M

1.8 M

Working width, m

4.2

3.6

3.0

2.4

1.8

Weight, kg

12.8

11.2

9.6

8

6.5

967 85 91-01

967 85 90-01

967 85 89-01

967 85 88-01

967 85 87-01

PART NUMBERS

WORKING TIME ON ONE CHARGE BATTERY

BV 30i

BLi 300

70 min

BLi 200

40 min

The runtimes are up-to times and correspond to work time using save™, with a fully charged battery. Your results may vary.

CHARGING TIME FOR DIFFERENT BATTERIES AND CHARGERS BATTERY

CHARGING CYCLES

QC 500 – CHARGING LEVEL

QC 330 – CHARGING LEVEL

BLi 300

1500

35 min

1h

55 min

1 h 20 min

BLi 200

1500

30 min

50 min

30 min

50 min

21

HUSQVARNA BE/BD SYSTEM | DOUBLE BEAM SCREEDS

DOUBLE FUNCTIONS, TWICE THE EFFECT The double beam screeds in the Husqvarna BE/BD system combine with a powerful BE drive unit to produce vibrations down to a thicknes of 150 mm. With BD double beam lengths from 3.2 m to 6.2 m you can work on any medium to large flooring construction sites.

22

You can use the BD double beam screeds for both surface vibration and levelling by rotating the drive unit 90 degrees. The sturdy, yet lightweight aluminum design allows for easy handling and excellent balance to achieve even concrete floors.

BE 20/BE 30

HUSQVARNA BE 20

COMPENSATE FOR NEGATIVE FLEXION

BE 20

Tensioning rods allow the screeds to camber two percent from the centre.

50 mm

SMART TWO-IN-ONE SOLUTION

100 mm

EFFICIENT VIBRATION Our double screeds come with 100 mm profile height, producing vibrations down to a thickness of 150 mm. The lightweight profile enables a higher stroke, resulting in efficient work in different conditions.

150 mm

IN-DEPTH ACTION On thin slabs up to 150 mm no vibration is needed beforehand.

HUSQVARNA BE 30

Rotating the drive unit BE 20 90 degrees allows our double beams to be used for both surface vibration and levelling. This makes them a popular choice for finishing concrete floors.

HIGHLY DURABLE AND EASY TO MOVE Lightweight, non-corrosive aluminium alloy makes for easy handling and transportation.

EASY CLEANING Parts exposed to wet concrete have smooth, easy-clean surfaces.

DRIVE UNIT

BE 20

BE 30

Drive model

ER355

HONDA GX120 UT1 SXS4 SD – 4 stroke

Voltage, V-Hz

400 V-3-50 Hz

—

Power, kW

0.45

2.6 for 3,600 rpm

Current, A

0.8

—

Speed, r.p.m.

3

3,6

Direction of rotation

Both

Counterclockwise

Tank capacity, l

—

2

Starting

Phase inverter switch

Recoil Starter

Sound Pressure Lpa dB(A)

—

75.7

Sound Power Lw dB(A)

94

103.8

Total weight, kg

37

32

967 95 64-01

967 94 12-02

PART NUMBERS

DOUBLE BEAM SCREEDS

BD 62

BD 52

BD 42

BD 32

Height, mm

100

100

100

100

Length, m

6.2

5.2

4.2

3.2

Width, mm

400

400

400

400

Total weight, kg

57

47

41

32

967 95 63-01

967 95 62-01

967 95 61-01

967 95 60-01

PART NUMBERS

23

HUSQVARNA BT 90 AND SV SYSTEMS | MODULAR TRUSS SCREEDS

EFFICIENT LEVELLING OF WIDE CONCRETE SURFACES Our modular truss screed systems are engineered to handle your biggest challenges. Assemble, adjust camber and go to work on anything from floors to bridges.

Husqvarna BT 90 truss screed system is engineered to handle concrete surfaces with a width of up to 25 metres.

24

Ideal for large surfaces. Handles concrete depths up to 200mm without the need for an internal vibrator with a production rate of 1 meter/minute. Available in electric, petrol and pneumatic versions.

SMART DESIGN A precision turn-buckle allows you to camber the screed sections independently.

400 V

3m 2m 1m 0.75 m 0.5 m 420 mm

Triangular frames and square tubes provide better rigidity. Oscillating bearings with grease nipples extend the product’s life-time and serviceability.

Small rubber crosses create an angle of 2.5° between each section.

Pneumatic

MODULES

ENGINEERED TO LAST

SMOOTH POWER

Petrol

376 mm

Winches equipped with 30 m of steel wire enable continuous screeding.

ENERGY

HUSQVARNA BT 90

BUILT-IN WINCHES

CONSISTENCY Low to high slump ADJUSTABLE CAMBER +/– 15°

EASY SETUP Can be easily assembled by a single operator.

The truss screeds allow a working width of 20 m (BT 90 P: 25 m).

BUILT TO PERFORM The low profile steel frame ensures durability, while the low centre of gravity provides stability in low slump concrete.

Examples of possible surfaces:

EVEN, CONTINUOUS PULL

HIGH PRODUCTIVITY

Winches on both sides are equipped with 30 m of steel wire. This allows continuous work over longer distances.

Once the selected rail system has been set-up, slabs can be made at a rate of 1 m per minute.

ELECTRIC

PETROL

PNEUMATIC

Powered by

400 V-3-50 Hz

—

3–6 bars

Input, kW

3

5 at 2900 r.p.m.

—

Minimum air flow, m³/m

—

—

0.26

Frequency, rpm

2865

2900

—

Working length, mm

560

560

355

Width × height, mm

545 ×1000

585 ×1000

610 × 970

Weight, kg

96

93

40

967 94 11-02

967 94 11-03

967 94 11-08

BT 90 MODULAR DRIVE SECTIONS

PART NUMBERS

BT 90 SCREED SECTION Height, mm

3 M, PNEUMATIC 2 M, PNEUMATIC 1 M, PNEUMATIC 3 M, ELECTRIC/ PETROL 376 376 376 376

2 M, ELECTRIC/ PETROL 376

1 M, ELECTRIC/ PETROL 376

0.75 M, ELECTRIC/ 0.5 M, ELECTRIC/ PETROL PETROL 376 376

Working length, mm

3000

2000

1000

3000

2000

1000

750

500

Total width, mm

420

420

420

420

420

420

420

420

Weight, kg

83

58

32

82

57

32

28

24

967 94 11-11

967 94 11-10

967 94 11-09

967 94 11-07

967 94 11-06

967 94 11-05

967 94 11-16

967 94 11-04

PART NUMBERS

ACCESSORIES BT90 594 71 09-01

Double electrical winch kit

596 86 44-01

Third man winch

594 86 05-02

Non vibrating extension – 0.5m

594 86 06-02

Outriggers

594 86 07-01

Crown invert bracket (pneumatic version)

596 86 42-01

Crown invert bracket (electric & gasoline version)

595 49 91-03

Skate

25

HUSQVARNA CT AND BG SERIES | WALK-BEHIND TROWELS

STAY IN CONTROL AND PERFORM Husqvarna walk-behind trowels are powerful machines, developed to deliver a smooth and durable concrete surface without compromising the operator’s productivity and safety. We offer a complete line of trowels including both electric and petrol-powered machines ranging from 600 mm to 1220 mm diameter.

26

When you choose a walk-behind trowel, you should consider the size of the surface, the type of concrete, weather conditions and any obstacles or narrow doorways.

VARIABLE SPEEDS

HUSQVARNA CT 36

Low speeds for floating, high speeds for burnishing. For wider speed range choose our models equipped with CVT clutch.

ENJOY THE POWER

OPTIMAL CONCRETE BURNISHING Possible to adjust blade pitch up to 30°.

TILT WITH EASE The maintenance stand facilitates service, blade changing and cleaning.

A single lifting eye makes transport easy.

HUSQVARNA BG 375

The vibration reduced and height adjustable handle is equipped with ergonomically assembled controls and smooth clutch engagement.

CHOOSING THE RIGHT TROWEL SIZE FOR THE JOB Edging

0–200 m²

0–250 m²

HUSQVARNA BG 245

HUSQVARNA CT 36 / BG 375 / BG COMBI HUSQVARNA CT 48 / BG 475

QUICKSTOP™

FOR YOUR SAFETY

IMMEDIATE HALT OF ROTATING TOOL – STOP MEANS STOP Our BG trowels stop immediately when you let go of the handle.

QUICKSTOP™ disengages the drive train from the powertrain, which makes rotation impossible.

GYROSCOPIC STOP

BUILT WITH PRODUCTIVITY AND SAFETY IN MIND On the CT range a gyroscopic sensor and gearbox brake detects the motion of the handle and stops the engine and handle rotation, preventing the operator from being struck by a runaway handle.

27

PETROL WALK-BEHIND TROWELS

CT 48

CT 36

Model code

13A-V ADJ-T

13A ADJ-T

8A ADJ-T

8A-V ADJ-T

8A ADJ-T

5A ADJ-T

Protection ring (Ø), mm

1220

1220

1220

915

915

915

Trowelling diameter, mm

1180

1180

1180

875

875

875

Weight (without handle), kg

106

102

96

90

84

73

Pitch range °

0–30

0–30

0–30

0–30

0–30

0–30

Rotor speed (min. / max.), rpm

20/200

60/125

60/125

20/200

60/125

60/125

Blade arm type

Bolt-on

Bolt-on

Bolt-on

Bolt-on

Bolt-on

Bolt-on

Quantity of blades

4

4

4

4

4

4

Type of handle

Adjustable

Adjustable

Adjustable

Adjustable

Adjustable

Adjustable

Engine / Motor manufacturer

Honda

Honda

Honda

Honda

Honda

Honda

Engine / Motor type

GX 390

Honda GX 390

GX 240

GX 240

GX 240

GX 160

Power, kW(Hp) @ 3600 rpm

8.7 (11.7)

8.7 (11.7)

5.9 (7.9)

5.9 (7.9)

5.9 (7.9)

3.6 (4.8)

Fuel consumption, l/h

2.7

2.7

2.7

2.7

2.7

1.8

Tank capacity, l

6

6

6.1

6.0

6.0

3.6

Clutch type

CVT-clutch

Centrifugal Clutch

Centrifugal Clutch

CVT-clutch

Centrifugal Clutch

Centrifugal Clutch

Transport device

Optional 2×4 bracket

Optional 2×4 bracket

Optional 2×4 bracket

Optional 2×4 bracket

Optional 2×4 bracket

Optional 2×4 bracket

Runtime, h

2.2

2.2

2.2

2.2

2.2

2.0

970 46 56-08

970 46 56-11

970 46 56-09

970 46 55-11

970 46 55-10

970 46 55-08

PART NUMBERS

ELECTRIC WALK-BEHIND TROWELS

BG 245

BG COMBI

Model code

E-F-TP

E-L-TP

E-L-TP

Protection ring (Ø), mm

615

1020

850

Operating weight, kg

60

88

86

Blade diameter, mm

605

850/915/980

850/915/980

Disc (Ø), mm

605

865/965/1015

865/965/1015

Blade speed, rpm

120

60/120

60/120

Number of blades

4

4

4

Type of handle

Short foldable

Long

Long

Pitch control

Twist-Pitch

Twist-Pitch

Twist-Pitch

Lifting hook

Standard

Standard

Standard

Transport wheels

Optional

Standard

Standard

Blade arm type

Bolt-on

Quick Release

Quick Release

Engine

230V-1-50Hz

400V-3-50/60 Hz

400V-3-50/60 Hz

Input power. Low/high speed, kW

1.5

1.6 / 2.4

1.6 / 2.4

Vibration value, m/s²

3.7

1.4

1.4

Sound power, guaranteed, LWa dB(A)

102

94

94

Sound pressure at operators ear, LpA dB(A)

86

77

77

967 92 93-01

967 92 95-01

967 92 94-01

PART NUMBERS

HUSQVARNA CT 48

HUSQVARNA BG

ACCESSORIES

ACCESSORIES 594 75 15-01

BG 475 and BG 375 wheel kit

596 19 23-01

BG 245 wheel kit

HUSQVARNA CT 36

597 15 54-01

Spare ring BG COMBI, ∅850 mm

ACCESSORIES

597 15 84-01

Spare ring BG COMBI, ∅1020 mm

598 92 88-02

598 92 88-01

28

Lifting bracket 48" (for use with a 2×4)

Lifting bracket 36" (for use with a 2×4)

CT 36

BG 475

BG 375

BG 245

5A FOLD ADJ-T

H9 L BC TP

H9 L BC TP

H6 L BC TP

H4 F BC TP

915

1200

950

950

615

875

1140

900

900

605

73

105

102

93

60

0–30

0 –18

0 –18

0 –18

0 - 18

60/125

40-115

40-115

40-115

40-115

Bolt-on

Bolt-on

Quick Release/Bolt-on

Quick Release/Bolt-on

Bolt-on

4

4

4

4

4

Foldable Adjustable

Long Foldable adjustable

Long Foldable adjustable

Long Foldable adjustable

Short foldable

Honda

Honda

Honda

Honda

Honda

GX 160

GX270

GX270

GX200

GX120

3.6 (4.8)

6.3 (8.4)

6.3 (8.4)

4.3 (5.8)

2.6 (3.5)

1.8

2.5

2.5

1.6

1.0

3.6

5.3

5.3

3.1

2.5

Centrifugal Clutch

Belt Clutch

Belt Clutch

Belt Clutch

Belt Clutch

Optional 2×4 bracket

Optional wheels

Optional wheels

Optional wheels

Optional wheels

2.0

2.1

2.1

1.9

2.5

970 46 55-09

967 92 92-01

967 92 91-01

967 92 90-01

967 92 88-01

BLADES AND FLOATING DISCS CT 48 Floating disc Floating disc Floating blade Finish blade Finish blade Finish blade Combo blade CT 36 Floating disc Floating disc Floating disc Floating disc Floating blade Finish blade Finish blade Finish blade Combo blade BG 475 – PRO LINE Floating blades Finishing blades Combination blades Finishing blades BG 475 – CLASSIC LINE Finishing blades BG 375 – PRO LINE Floating disc (9 hp only) Floating blades Finishing blades Combination blades Finishing blades BG 375 – CLASSIC LINE Floating disc (9 hp only) Finishing blades Combination blades BG 245 – PRO LINE Floating disc Combination blades Finishing blades BG 245 – CLASSIC LINE Floating disc Combination blades BG COMBI – PRO LINE Floating blades Finishing blades Combination blades Finishing blades BG COMBI – CLASSIC LINE Floating disc Floating disc Floating disc

PRODUCT NUMBER

TYPE

MATERIAL

DIAMETER, MM

WIDTH, MM

LENGTH, MM

PCS/PACK

598 93 02-02 599 50 74-01 598 92 98-03 598 92 98-01 599 50 65-01 599 50 65-02 598 92 98-02

Clips Clips Slide-on Bolt on Bolt on Bolt on Bolt on

Steel Steel Steel Steel Steel Steel Steel

1213 1200 — — — — —

— — 254 152 160 160 203

— — 457 457 465 465 457

2 1 4 4 4 40 4

598 93 02-01 598 93 03-01 599 50 70-01 599 50 70-02 599 34 36-01 598 92 95-01 599 50 67-01 599 50 67-02 598 92 95-02

Clips Clips Clips Clips Slide-on Bolt on Bolt on Bolt on Bolt on

Steel Steel Steel Steel Steel Steel Steel Steel Steel

972 972 966 966 — — — — —

— — — — — 254 152 160 160

— — — — 356 356 356 356 356

2 10 1 10 4 4 4 40 4

594 20 78-01 594 86 71-01 594 86 70-01 594 86 74-01

Bolt-On Bolt-On Bolt-On Bolt-On

Steel Steel Steel —

— — — —

247 150 200 150

467 460 458 458

4 4 4 4

594 19 86-01

Bolt-On

Steel

—

153

459

4

594 24 36-01 594 19 83-01 594 22 76-01 594 86 69-01 594 86 73-01

Slide-On Finishing Blades Quick-Release Quick-Release Bolt-On Bolt-On

Steel Steel Steel Steel Plastic

950 — — — —

1 218 153 200 153

— 358 376 337 376

— 4 4 4 4

594 24 02-01 594 71 11-01 594 86 68-01

Slide-On Finishing Blades Bolt-On Bolt-On

Steel Steel Steel

950 — —

1 152 200

— 355 337

4 4

594 24 40-01 594 70 99-01 594 86 72-01

Slide-On Finishing Blades Bolt-On Bolt-On

Steel Steel Plastic

608 — —

1 127 125

235 227

4 4

595 07 12-01 594 86 67-01

Slide-On Finishing Blades Bolt-On

Steel Steel

610 —

1 127

235

4

594 19 83-01 594 22 76-01 594 86 69-01 594 86 73-01

Quick-Release Quick-Release Bolt-On Bolt-On

Steel Steel Steel Plastic

— — — —

218 153 200 153

358 376 337 376

4 4 4 4

594 24 10-01 594 24 36-01 594 24 12-01

Slide-On Finishing Blades Slide-On Finishing Blades Slide-On Finishing Blades

Steel Steel Steel

865 950 1015

— — —

— — —

1 1 1

29

HUSQVARNA CRT SERIES | RIDE-ON TROWELS

TACKLE BIG SLABS IN TOTAL CONFIDENCE When finishing concrete slabs, challenges can be many.

Worrying about equipment should not be one of them.

Our complete new range of ride-on trowels will enable you to achieve great results on any job site, no matter the size. The ride-on trowels offer the torque, speed and smart features to finish the job at hand with confidence, while delivering exceptional floor flatness (FF).

30

The new range of ride-on trowels consists of 2 × 36" (2 × 900 mm), and 2 × 48" (2 × 1200 mm) machines.

All machines have an excellent power-to-weight ratio, providing adequate power to the rotors and ensuring high driving speed.

OPTIMUM MANOEUVRABILITY Thanks to its balanced power-toweight ratio and ergonomic twin lever controls.

GOOD VISIBILITY

HUSQVARNA CRT 48

Front and rear lights are standard to enable you to perform in dim light and during night.

HIGH PRODUCTIVITY AND GREAT FINISHES

SMOOTH AUTOMATIC OPERATION

Thanks to top blade speeds.

A variable clutch offers proper torque and speed range to match concrete conditions without mechanical adjustments. Since the clutch helps to keep constant torque the belt life is prolonged.

CHOOSING THE RIGHT TROWEL SIZE FOR THE JOB 250–1000 m²

1000–2000 m²

1000–2500 m²

HUSQVARNA CRT 36

HUSQVARNA CRT 48

HUSQVARNA CRT 48 PS

31

RIDE-ON TROWELS

CRT 48 PS

CRT 48

Model name

CRT 48–57K-PS

CRT 48-35L-PS*

CRT 48-37V

L × W × H Operating, mm

2566 × 1295 × 1488

2566 × 1295 × 1473

2566 × 1295 × 1473

Shipping weight, kg

815

792

663

Operating weight, kg

660

639

547

Trowelling diameter, mm

1219

1219

1220

Quantity of blades

10

10

10

Pitch range °

0–25

0–25

0–25

Rotor speed (min. / max.), rpm

25/150

25/150

25/170

Engine / Motor manufacturer

Kubota

Kohler

Briggs & Stratton

Power, kW (Hp) @ 3600 rpm

42.5 (57)

26 (35)

27.6 (37)

Fuel

Petrol

Diesel

Petrol

Fuel consumption, l/h

9.5

6.2

10

Tank capacity Fuel, l

24.6

24.6

24.6

Retardant tank capacity, l

24.6

24.6

24.6

Runtime, h

2.6

4.0

2.5

970 46 16-13

970 46 16-09

970 46 16 05

PART NUMBERS

* not avaible in EU.

BLADES AND DISCS

32

PRODUCT NUMBER

DESCRIPTION

TYPE

DIAMETER, MM

WIDTH, MM

LENGTH, MM

THICKNESS, MM

QTY

CRT 36 Floating disc Floating disc Floating disc Floating disc Floating blade Finish blade Finish blade Finish blade Combo blade

598 93 02-01 598 93 03-01 599 50 70-01 599 50 70-02 599 34 36-01 598 92 95-01 599 50 67-01 599 50 67-02 598 92 95-02

Pak-Pan, 36 Dia-2 pcs Pallet-Pan, 36 Flat float,10 pc Floating disc 36" Floating disc 36" – 10 Set-float blades, 4 per Set-finish blades, 4 per Finish blade kit 36" Finish blade kit 36" – 10 SET-Combo blades, 4 per

Clips Clips Clips Clips Slide-on Bolt on Bolt on Bolt on Bolt on

972 972 966 966 — — — — —

— — — — 254 152 160 160 203

— — — — 356 356 356 356 356

— — — — — — 3 3 —

2 10 1 10 4 4 4 40 4

CRT 48 Floating disc Floating disc Floating disc Floating disc Floating disc Floating blade Finish blade Finish blade Finish blade Combo blade

598 93 02-03 598 93 02-04 598 93 03-03 598 93 03-04 599 50 74-05 598 92 98-03 598 92 98-01 599 50 65-01 599 50 65-02 598 92 98-02

Pak-Pan,48 Dia.(5-blade), 2 pc.

Pak-Pan, 48 Flat (5-blade), 2 pc.

Pallet-Pan,48, (5-blade),10 pc.

Pallet-Pan 48 Flat(5-blade),10 pc Floating disc CRT 48-31V Set-Float Blades, 4 per Set-Finish Blades, 4 per Finish blade kit 48" Finish blade kit 48" – 10 Set-Combo blades,4 per

Clips Z Clip Style Clips Z Clip Style Clips Slide-on Bolt on Bolt on Bolt on Bolt on

1213 1219 1213 1219 1200 — — — — —

— — — — — 254 152 160 160 —

— — — — — 457 457 465 465 —

— — — — — — — 3 3 —

2 2 10 10 2 4 4 4 40 4

CRT 60 Floating disc Finish blade Combo blade

598 93 08-01 598 93 07-01 599 06 42-01

Float-Pan 60" Blade-kit, 4 finish, 60 Blade-kit, 4 combo, 60

Z Clip Style Bolt on

— — —

— 152 —

— 584 —

— — —

1 4 4

CRT 48

CRT 36

CRT 48-33K

CRT 48-33K-DF

CRT 48-35L*

CRT 36-26A

2566 × 1295 × 1473

2566 × 1295 × 1473

2566 × 1295 × 1473

2032 × 1041 × 1372

733

—

822

505

579

579

603

451

1219

1219

1220

2 × 915

10

10

10

8

0–25

0–25

0–25

0–25

25/160

25/160

25/150

25 /165

Kubota

Kubota

Kohler

Honda

23.1 (31)

23.1 (31)

26 (35)

16.4 (22)

Petrol

Petrol/LPG

Diesel

Petrol

11,6

11.6/7.5

10

6.7

24.6

24.6/15

24.6

24.6

24.6

24.6

24.6

24.6

2.1

2.1 /2.0

4.0

3.3

970 46 16-10

970 46 16-12

970 46 16-02

970 46 14-03

HUSQVARNA CRT 48 PS ACCESSORIES 598 92 90-01

Transport trolley wheel kit

598 92 99-01

Transport whel replacement wheels (2) for wheel kit

598 92 91-01

Weight kit set of 2 (4.5 kg each)

HUSQVARNA CRT 48 ACCESSORIES 598 92 90-01

Transport trolley wheel kit

598 92 99-01

Transport whel replacement wheels (2) for wheel kit

598 92 91-01

Weight kit set of 2 (4.5 kg each)

33

USE YOUR CONCRETE TROWEL TO POLISH CONCRETE FLOORS WITH HIPERTROWEL™ As a specialist in concrete trowelling you have a unique oppurtunity to grow your business. Polished concrete floors are continuously growing as a prefered choice in industrial flooring thanks to their low life cycle cost and easy maintenance properties.

The Husqvarna Hipertrowel™ system is ideal for large, unobstructed areas and where the surface flatness is already sufficient.

Contact your local Husqvarna application specialists to guide and support you.

34

WHAT TYPE OF PROJECTS ARE SUITABLE?

WHAT END-RESULT CAN YOU PRODUCE?

The Hipertrowel™ method is ideal for industrial floors from 500 m² and up. Both newly poured slabs and older, pre-­existing floors can be processed with the Hipertrowel™ system.

The Hipertrowel™ system allows you to produce a nice salt and pepper-looking industrial floor with a satin or glossy finish.

HIPERTROWEL™ IS THE IDEAL SOLUTION WHEN ■

Time is the most critical parameter

■

The surface is 500 m² or more

■

There are no obstacles (pillars etc.)

■

The floor does not need to be leveled

■

No aggregate needs to be exposed

■

Wet grinding is not an issue

■

A good slurry management system is on site

BEFORE: Troweled concrete surface

AFTER: Glossy salt and pepper surface

FAST INDUSTRIAL CONCRETE POLISHING

Production rates can vary significantly depending on the process chosen and the end-result you want to achieve. Also, size of the floor, concrete quality and hardness as well as obstacles on the floor impact productivity.

FIND OUT MORE AT: WWW.HUSQVARNACP.COM 35

SOFF-CUT 4200

SOFF-CUT 4000

SOFF-CUT 2000

SOFF-CUT 150

HUSQVARNA ULTRA EARLY ENTRY™ SAW | SOFF-CUT

CUT ULTRA-EARLY FOR STRAIGHT LINES – DON’T WAIT FOR RANDOM CRACKS Husqvarna Soff-Cut is ideal for the ultra-early sawing of contraction joints after pouring concrete slabs. The system is designed to minimize the risk of random cracks – one of the most costly and aggravating problems faced by concrete contractors. The main benefits are the high

36

production rates, the ability to pour and cut concrete on the same day, and of course, the tidy end result achieved by only cutting shallow depths.

STRAIGHT CUT

HUSQVARNA SOFF-CUT 4200

The foldable front guide makes it easy to follow a straight line for the cut.

STURDY PROTECTION The high-strength, lightweight aluminium frame protects the engine.

MINIMAL FOOTPRINT Smart design, lightweight frame and wide wheels ensure minimal machine footprint on the concrete.

LESS NOISE AND DUST The blade block enclosure reduces noise while the created dust can optionally be vacuumed directly though the VAC port.

NO CHIPPING AND SPALLING Up-cut rotating diamond blade, anti ravel skid plate and arbor allows for same-day sawing.

ULTRA EARLY ENTRY™ SAW*

SOFF-CUT 4200

SOFF-CUT 4000

SOFF-CUT 2000

SOFF-CUT 150

Engine manufacturer

Kohler

Kohler

Kohler

Kohler

Max power, kW **

17.2

14.9

6.5

4.0

Max blade diameter, mm

350

350

250

150

Max depth of cut, mm

76

70

38

30

Weight, kg

257

191

144

40

CE certified

—

Yes

Yes

Yes

589 94 90-01

—

—

589 94 90-01

966 84 56-05

966 84 55-06

966 84 53-04

966 84 48-16

XL10

XL6

ACCESSORIES Vac attachment cover PART NUMBERS

* With VAC port. ** As rated by the engine manufacturer.

XL14 BLADE

2000

MATERIAL Very hard to hard aggregate concrete Hard to medium-hard aggregate concrete Soft to very soft aggregate concrete

l

l

3000

5000

—

— —

l

— —

l

l

l

—

l

l

2000

l

l

l

3000

5000

—

— —

l

— —

l

l

l

—

l

l

2000

l

l

l

— —

3000

5000

—

— —

l l

l l

—

l

l

l

RECOMMENDED EQUIPMENT SC 4200, SC 4000 l

l

l

= Optimal

l

l

= Good

l

= Acceptable

SC 2000e

SC 150

— = Not recommended

Husqvarna XL14 / XL10 / XL6.

PRODUCT NUMBER

NAME

DIAMETER, MM

SEGMENT SHAPE

SEGMENT LENGTH, MM

SEGMENT THICKNESS, MM

SEGMENT HEIGHT, NUMBER OF MM SEGMENTS

BORE

XL14 542 75 61-13 542 75 61-14 542 75 61-16

XL14-2000 XL14-3000 XL14-5000

350 350 350

Flat Flat Flat

40 40 40

3.2 3.2 3.2

9 + 2.5 9 + 2.5 9 + 2.5

24 24 24

Soff-Cut Triangular Soff-Cut Triangular Soff-Cut Triangular

XL10 542 75 61-01 542 75 61-02 542 75 61-04

XL10-2000 XL10-3000 XL10-5000

250 250 250

Flat Flat Flat

40 40 40

2.6 2.6 2.6

9 + 2.5 9 + 2.5 9 + 2.5

17 17 17

Soff-Cut Triangular Soff-Cut Triangular Soff-Cut Triangular

XL6 542 77 70-06 542 77 70-07 542 77 70-09

XL6-2000 XL6-3000 XL6-5000

150 150 150

Flat Flat Flat

32 32 32

2.6 2.6 2.6

8 + 1.5 8 + 1.5 8 + 1.5

12 12 12

Soff-Cut Triangular Soff-Cut Triangular Soff-Cut Triangular

Additional blades on request.

37

CONCRETE PLACEMENT GUIDE

HOW TO SUCCEED WITH YOUR APPLICATIONS CONCRETE VIBRATION It is important to vibrate freshly poured concrete. The vibrations make the concrete fill out into all hollows of the construction. The process also evacuates air bubbles, optimizes the spread of the aggregate and maximizes cohesion of the cement mix and the rebar.

This results in a resistant, long-lasting concrete with the correct calculated strength.

How to succeed with concrete vibration.

Choose the right size.

DON’T WAIT

The wrong vibrator size and/or placement will result in non-vibrated areas.

Begin vibration when concrete is being poured.

Start where the concrete has first been poured.

Then follow the concrete as it is poured, vibrating all the way.

VIBRATE JUST ENOUGH Stop when the surface becomes shiny or if a large bubble pops up near the vibrator. Don’t over-vibrate as this is just as harmful as under vibration or non-vibration.

APPLY IN THE RIGHT ANGLE Apply the vibrator vertically at an angle of 90 degrees. Never below 45 degrees.

V

V

V

V

V

V

Proper vibrator size and placement ensures the entire slab gets vibrated. Optimal vibrator overlap is 2 × vibrator diameter.

Some helpful tips before vibration.

PLAN THE VIBRATION Calculate the dip intervals. More power and a larger diameter on the vibrator results in fewer dips, which means higher productivity.

LUBRICATE THE HOSE Before starting with the vibration, spray specific shutter plate oil on the vibrator hose. This will help stop concrete sticking to the hose, making it easier to clean afterwards.

ENSURE CONSISTENT POWER SUPPLY Electric current should never vary more than +/– 10% as this will affect productivity and the life of the vibrator.

38

Radius of action is 8–12 × vibrator diameter, depending on vibrator.

How to choose the right type of vibrator for your project.

01

Consider the type of application.

VIBRATOR

SMART

ENERGY

l

SMART-E

AX

VIBRASTAR

l

= Optimal

AA

HIGH FREQUENCY ELECTRIC —

l

l

l

AZ

= Good

l

= Acceptable

AME 600

MECHANICAL

— = Not recommended

AME 1600

MODULAR FLEX-SHAFT

AY PNEUMATIC

Columns

l

l

l

Beams

l

l

l

Walls

l

l

l

Floors

l

l

l

Bridges

l

l

l

—

l

l

l

—

l

—

—

Tunnels

l

l

l

l

l

l

l

—

—

—

—

Foundations

l

l

l

—

l

l

l

Retainings walls

l

l

l

—

l

l

l

Car parks

l

l

l

l

l

l

l

l

Structures

l

l

l

l

l

l

l

l

Harbours

l

l

l

—

l

l

l

—

Dams

l

l

l

l

l

l

l

—

Precast form

l

l

l

l

l

l

l

l

l

l

—

—

Slip form

l

l

l

l

l

l

l

l

l

l

—

—

—

—

l

Pre-slab

l

l

l

l

l

l

l

l

l

l

—

—

—

—

l

02

l

l

— l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

— l

l

l

—

l

l

— l

l

l

l

l

l l

l

l

l

l

l

l

l

l l

l

l

MEDIUM JOBS

ELECTRIC

CF & AX/VIBRASTAR OR SMART/SMART-E

AME 1600 & AT & SUPERFLEX OR AME 600 & HA

l

l

—

—

l

l

—

l

—

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

—

03

LARGE JOBS

l

l

l

Consider the power supply available.

ENERGY

l

—

l

l

— l

l

—

l

l

l

l

l

l

l

l

l l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

— l

l

l

Consider the rebars.

To define the optimal diameter of the vibrator, consider the distance between the rebars. The distance between rebars must be large enough for your vibrator.

PETROL

AX/VIBRASTAR

PNEUMATIC

AY

04

AMG 3200/AMD 3000 & AA/AZ

To choose the optimal radius of action, consider the area of the slab and the slump of the concrete.

VIBRATOR RADIUS OF ACTION

SMART

SMART-E

AX

VIBRASTAR

AA

AZ

AME 600

AME 1600

AY

12×vibrator Ø

12×vibrator Ø

10×vibrator Ø

8×vibrator Ø

10×vibrator Ø

8×vibrator Ø

8×vibrator Ø

10×vibrator Ø

10×vibrator Ø

Slump S 5 >220 mm

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

Slump S 4 210–160 mm

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

Slump S 3 150–100 mm

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

Slump S 2 90–50 mm

l

l

l

l

l

l

l

l

l

l

l

l

Slump S 1 40–10 mm

l

l

l

l

l

l

l

l

—

l

l

l

l

l

l

l

l

l

l

—

—

—

l

l

l

39

CONCRETE LEVELLING AND SURFACING Levelling ensures every part of the newly poured concrete slab achieves the desired level. Surfacing ensures the finish of the slab suits its intended purpose.

SURFACE

PRODUCTS

SCREEDED SURFACE (ROUGH)

FLOATED SURFACE (ROUGH)

OR

STEEL TROWELLED SURFACE (SMOOTH)

OR

SCREEDS Screeds are used for levelling a slab and vibrating thinner slabs.

For slabs thicker than the screed’s vibration depth, use a vibrator.

Consider the following factors when choosing suitable screeding equipment.

Desired levelness or flatness of floor

Area to cover and time available

Available power supply

Type of slump

Thickness of the concrete layer

How to succeed with screeding.

Make sure the pouring process is carried out seamlessly, and that you have enough concrete to cover the entire area.

Remove the excess concrete with a rake before screeding to ensure optimal flatness.

Never step on a slab that has already been screeded.

40

TROWELS Trowels are used to finish a concrete floor. They use pressure to make the surface flatter and smoother.

ENERGY

0 – 200 m², Ø 610 mm

0 – 200 m², Ø 900 mm

0 – 200 m², Ø 900 mm

0–250 m², Ø 1140 mm

0–250 m², Ø 1220 mm

BG 245

CT 36

BG 375

BG 475

CT 48

PETROL

250–1000 m², Ø 2050 mm

1000–2000 m², Ø 2570 mm

1000–2500 m², Ø 2570 mm

CRT 36

CRT 48

CRT 48 PS

0 – 200 m², Ø 610 mm

0 – 200 m², Ø 850 mm

0–250 m², Ø 1220 mm

BG 245E

BG COMBI

BG COMBI

PETROL

ENERGY ELECTRIC

Consider the following factors when choosing trowelling equipment.

Area to cover

Usage of discs or blades

Type of slump

How to succeed with trowelling.

Available power supply

Size of the aggregate

W e only recommend to start turning the machine once the concrete starts to set, using finishing blades.

egin slowly. When concrete is fresh, it is fragile. If you go too fast, B you may flush concrete away and create holes. Increase your speed as the concrete is curing.

I f you require a smoother surface, continue with finishing blades or combination blades.

F or the first 1–3 passes, use floating discs or floating blades.

For a flatter floor, use a ride-on trowel and more passes.

C hoose blades made from the right material. Steel and carbon blades are flexible and last longer, but may alter the color of the concrete. If color is important, e.g. when color pigments are mixed in, use plastic blades.

First pass shall be orthogonal (90°) to the direction of the screed pass.

T he following passes to be done in square pattern and half a rotor overlap in order to ensure better flatness.

High ambient temperatures cause concrete to dry quicker. So, if it is hot outside, the amount of time you have to trowel the concrete is reduced.

EXTEND YOU BUSINESS

CREATE POLISHED CONCRETE FLOORS USING RIDE-ON TROWELS Efficiently create sustainable polished concrete floors using trowels.

Husqvarna’s new optimized Hipertrowel™ concept includes all you need; machine, diamond tools, chemicals and support.

For more information visit our website: www.husqvarnacp.com 41

CONTRACTION JOINT SAWING As the concrete slab hydrates and begins to set, it develops internal stresses. These stresses need to be relieved in a controlled way before they seek their own relief in the form of a random crack. By cutting control joints as a final step of the finishing process, you create a pattern of predetermined weakened planes in the concrete, that subsequently crack at the bottom of the cuts.

The Ultra Early Entry™ solution.

How to succeed with Husqvarna Soff-Cut®.

The Husqvarna Soff-Cut® system is the optimal way to control random cracking. With ultra-early entry cutting you can control cracking in slabs up to 225 mm thick, with only a 25 mm minimum depth, within the green zone (1–2 hours after pouring).

Start sawing as soon as you’re sure the concrete will support the weight of the saw and operator without marking or damaging the concrete. You don’t have a lot of time.

Determine the layout of the joints in advance. Ensure straight cuts by drawing guidelines on the surface to follow.

If possible, start the job with a new, unused Husqvarna XL Series dry-cutting diamond blade and anti-ravel skid plate.

Consider the following factors when choosing your Soff-Cut machine.

Desired levelness or flatness of floor

Area to cover and time available

Available power supply

MAX CUTTING DEPTH

SOFF-CUT 4200

SOFF-CUT 4000

SOFF-CUT 2000

38 mm 76 mm

30 mm

70 mm

> 2 000 m2

> 2 000 m2

> 00 20 m²

> 00 20 m²

0

0 2 1 000 -20–²2 000 m

0 m 100

AREA

< 0 100 m²

< 1 000 m2

2–3 m/min

SPEED

4.6–7.6 m/min 6–9 m/min > 00 20 m²

42

SOFF-CUT 150

6–9 m/min

> 00 20 m²

0 00 0-2 m² 100

< 0 100 m²

The minimum depth of the contraction joint should be 1/8 of the slab’s thickness and no less than 25 mm.

43

HUSQVARNA EXPERTS AT YOUR SERVICE All concrete equipment from Husqvarna should be easy to use, but also easy to buy, own, service and repair – that’s the main idea behind our service concept. At our service centers you’ll meet dedicated, highly skilled personnel – experts on Husqvarna concrete equipment.

They know that fast and correct service and repair of the equipment is essential for professional users. To ensure a seamless service process, all authorised Husqvarna service and parts personnel have access to an on-line Service Tool, which supports all service and repair functions, enabling shorter lead times and higher service quality.

44

45

46

47

husqvarnacp.com Copyright © 2021 Husqvarna AB (publ). All rights reserved. Husqvarna and other product and feature marks are trademarks of the Husqvarna Group.

We reserve the right to make changes in technology and specifications without prior notice.