Digital%20gauges%20fitting%20instructions

Purple connect to headlights or parking lights, to dim display.

Blue signal Red +12V Fuse 5A

Black Negative

p/n 310.401 Gauge only

Installation 1. Cut a ﾘ53mm hole and fit gauge.

2. Disconnect Battery.

3. Connect the black wire to a good chassis ground.

Ensure good ground connection between temperature sender unit.

4. Connect the red wire to a fuse accessory or the ignition switch circuit.

5. Connect the blue wire to the temperature sender unit.

6. For coolant temp. fit the temp sender into the engine block.

7. Display Dimmer, connect the purple wire to headlights or parkers 12V to cut the brightness by 50% .

8. Re-connect Battery.

Blue wire from Gauge

To battery negative

Two terminals senders

40 - 120ｺC

FA 18 July 2011

Purple connect to headlights or parking lights, to dim display.

Blue signal

Red +12V Fuse 5A

Black Negative

p/n 310.701 Gauge only

Installation 1. Cut a ﾘ53mm hole and fit gauge.

2. Disconnect Battery.

3. Connect the black wire to a good chassis ground.

Ensure good ground connection between temperature sender unit.

4. Connect the red wire to a fuse accessory or the ignition switch circuit.

5. Connect the blue wire to the temperature sender unit.

6. For transmission temp. fit the temp sender in place of the drain plug in the transmission pan.

7. Display Dimmer, connect the purple wire to headlights or parkers 12V to cut the brightness by 50% .

8. Re-connect Battery.

Green wire from Gauge

To battery negative

Two terminals senders

50 - 150ｺC

FA 18 July 2011

Purple connect to headlights or parking lights, to dim display.

Red +12V Fuse 5A

Black Negative

p/n 332.401 Gauge only

Installation 1. Cut a ďž˜53mm hole and ďŹ t gauge.

2. Disconnect Battery.

3. Connect the black wire to a good chassis ground.

4. Connect the red wire to a fuse accessory or the ignition switch circuit.

5. Display Dimmer, connect the purple wire to headlights or parkers 12V to cut the brightness by 50% .

6. Re-connect Battery.

FA 18 July 2011

Oxygen Sensor Narrow Band 0 - 1V There are four different type of oxygen sensors with 1, 2, 3 or 4 wires connector.

Connect: Grey wire from gauge to sensor signal wire Grey or Blue on plug to PCM

Grey to Oxy sensor

The 3 and 4 wire sensors have inbuilt a heating element.

The VDO Oxygen sensor has Grey (or Blue) signal wire on a four terminals connector.

Red +12V Connect the digital gauge p/n 301.401 Air/Fuel Ratio, Grey wire to the oxygen sensor Grey (or Blue ) wire.

Fuse 5A

Black Negative The gauge can be used for Unleaded Petrol, Methanol, Ethanol and Propane. p/n 301.401 Gauge only

(p/n 301.402 Kit)

Note: Gauge is designed to operate off a 渡arrow band・ Oxy Sensor 0 - 1V

Installation 1. Cut a ﾘ53mm diameter hole and fit gauge.

2. Disconnect battery 3. Connect the black wire to a good chassis ground.

Ensure good ground connection between oxygen sender unit.

4. Connect the red wire to a fuse accessory or the ignition switch circuit.

5. Connect the gauge痴grey wire to grey or blue Oxygen sensor plug to PCM (Powertrain Control Module).

6. Re-connect the battery

Air Fuel Ratio Instructions The air fuel ratio gauge consists of 10 LEDs (light emitting diode) to represent the air to fuel ratio.

When power is applied to the gauge, the word rich will light at the top, of the gauge and the word lean will light at the bottom of the gauge.

The gauge works by monitoring the 0 to 1 Volt signal coming from the oxygen sensor. The higher the voltage, the richer the condition. The lower the voltage, the leaner the condition. When the vehicle is running full rich all the LED light bars will be lit.

The lit bars start at the bottom and will progressively light to the top. Each bar represents 0.1 Volt.

2 red, 2 yellow and 1 green represents a stoichiometric condition, (lowest emissions).

0 to 0.3 Volt, (or less), 2 red, 1 yellow represents a lean condition.

This is fine at idle or low cruising speeds.

At full throttle, heavy load condition, the gauge should have most or all of the bars lit. If the vehicle is computer equipped then the gauge will fluctuate up and down, at cruising or idle speeds, this is normal. The computer is constantly adjusting the air/fuel ratio for lowest emissions. The stoichiometric air/fuel ratio is the chemically correct ratio at which all of the oxygen and all of the fuels consumed. This condition is neither rich nor lean. This condition represents lowest emission, however maximum horsepower is developed at a rich condition. A lean condition under load, is danger ous and could result in severe engine damage.

A faulty oxygen sensor or bad ground could cause the gauge to indicate a lean condition.

All sensors are supposed to operate the same however our tests have shown that some sensors are sluggish compared to others.

A heated sensor is not needed unless you need to get an instantaneous reading when the car is first turned on. It is recommended that you bring the engine up to normal operating temperatures before racing the engine.

By this time the sensor will also be up to operating temperature.

Fouling or permanent damage will occur if using the sensor with leaded or fuel additives containing lead, 2 cycle gasoline (gas + oil mixture), diesel fuel, nitro methane, or excessively rich mixture.

FA 18 July 2011

Purple connect to headlights or parking lights, to dim display.

Orange signal Red +12V Fuse 5A

Black Negative

p/n 350.401 Gauge only

Installation

1. Cut a ďž˜53mm diameter hole and ďŹ t gauge.

2. Disconnect battery 3. Connect the black wire to a good chassis ground.

Ensure good ground connection between oil sender unit.

4. Connect the red wire to a fuse accessory or the ignition switch circuit.

5. Connect the gauge Orange wire to pressure sensor terminal.

6. Display Dimmer connect the purple wire to headlights or parkers 12V to cut the brightness by 50% .

7. Re-connect battery

Orange wire from Gauge

To battery negative

FA 18 July 2011

Purple connect to headlights or parking lights, to dim display.

Distributor

Green signal Ignition Coil Elect. Ign. Module

Red +12V Fuse 5A

Black Negative

p/n 333.003 Gauge only

Installation 1. Cut a ﾘ53mm diameter hole and fit gauge.

2. Disconnect battery.

3. Set switches to 渡umber of cylinders・before connecting LED tacho to power) 4. Connect the black wire to a good chassis ground.

5. Connect the red wire to a fuse accessory or the ignition switch circuit.

5. Connect the gauge green wire to negative side of ignition coil.

6. Display Dimmer connect the purple wire to headlights or parkers 12V to cut the brightness by 50% .

7. Re-connect battery.

Note: The red or black wire MUST be removed before adjustment to the cylinder setting, which is made from the 田ylinder selector・switch.

FA 18 July 2011