SITELECTRIC-STAND DESK Instruction Manual M07-23D/M07-23R
Instructions of Safety and Warnings:
• C ear up al obstacles within the he ght adjustment range
1 2
• Any failure to comp y w th the safety and installat on instruct ons in this manual may cause serious bodily in ury
• Users should make sure that they never sit on the desktop in order to prevent serious bod ly njury.
Never operate the system if it's in mo st environment or its electr cal components have contact with iqu ds
• Any attempts to reconstruct the desk frame aren't a lowed.
Never operate the system with a damaged cord or plug. Please contact your point of purchase to replace the damaged parts
• Don t add anyth ng to the adjustable junct ons of the desk frame.
CAUT ON
Don t clean the product with water whi e the power is st l connected.
Any incomplete observation of the nstructions warn ngs and additiona informat on marked w th the "Note" and " " may result n ser ous damage to the system or its components.
•• This product can be used by chi dren aged from 8 years and above if they have been g ven superv sion or nstruction concerning use of the appliance in a safe way and understand the hazards involved Chi dren shal not play w th the appl ance Clean ng and user ma ntenance shall not be made by ch ldren w thout supervision. Unplug the desk when the system isn t in use, and place the power plug out of ch ldren reach.
The product is powered by electricity In order to avo d burns, fire and electric shock p ease read the instructions carefully
• Persons w th reduced physical, mental abil t es and or lack of experience and know edge must not use the product, unless they're under supervision, understand the hazards involved or they have been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of these persons
Other Safety Instructions:
• Don t leave the cords or p ug unorganized in order to prevent tripping hazards
Preface
Electrical Safety Instructions:
This e ectric height adjustable standing desk consists of a heavy-duty steel desk frame and a motorized height adjustment system. Please read and comp etely understand this manual before nstal ation in order to make sure the safe and correct use of the system and ma ntain the longevity of the overa l construction and the built-in e ectronics
CAUT ON
Don't operate the system f the control box makes noise or odor. Alterations of the given power unit and control box aren't a lowed.
Don t disassemble or replace components whi e the power is st l connected.
• Outdoor use is prohib ted.
Preparation Checklist and Installation
Phil ips Screwdr ver
A (x1) Crossbar B (x2) Side Bracket D (x2) Foot C (x2) Lifting Column G (x1) Power Plug E (x1) Fix ng P ate F (x1) Control Box I (x2) Tray Hanger J (x1) Controller
3 4
What are the specifications you need to know?
2
H
Bubb e Level Allen Wrench (Included) Drill
Th s page can be torn so that t's easier for you to match the components w th the images
Disposal The product w th this mark ndicates that this product shou dn't be disposed w th other household wastes throughout the EU. To prevent poss b e harm to the environment or human hea th from uncontrol ed waste disposal recyc e it respons b y to promote the sustainab e reuse of mater al resources. To return your used device p ease use the loca recyc e service or contact your point of purchase to w thdrawn the product
A Shipping Blanket to protect the desk and the floor
1
3
The picture of the contro er s for your reference on y Actual product may vary (x1) Management Tray
Power
Operation
What are the tools you require while installation?
Weight Capacity 125kg (275lbs) Input (100~240V) Temperature (-5 ~+ )°C 40°C
Cable
Things you need to know before installation
4 P ease check a l of the components shown in the component check ist. f any of the components are m ss ng or damaged contact your po nt of purchase for a replacement.
What's the thing you'd better have before installation?
S-B (x8) Hex Head Screw
S-C (x10)
Note: The draw ngs of both of the crossbar and side brackets are the backside of the components P ease make sure the crossbar and side brackets keep fac ng down whi e insta lat on, which is convenient for the further steps
A B AB A B
5 6
Shipping Blanket
• Please prepare a spacious area for installation and put a sh pp ng b anket on the area to prevent scratches
• Attach the side brackets to the end of the crossbar . (This step doesn't requ re the use of the screws.)
• Carefu ly place the desktop(not included) upside down on the blanket
S-I (x1) Al en Wrench
Attaching Side Brackets
Phi lips Head Screw+ 1 Spacer
S-A (x8)
Now let's start the installation.
S-F (x4) Phi lips Head Screw
• Place the crossbar and side brackets on the top
S-E (x2) Phil ips Head Screw
S-D (x2)
S-G (x3) Cable Clip
S-H (x10) Ant -Vibration Pad
Ph llips Head Screw
Hex Head Screw
•
Loosen the hex head screws that fix the adjustab e junction, but don't completely take out the screws.
• Ensure that the frame is placed n the center of the table Then adjust the frame to suit the s ze of the tab etop.
S-I
When adjusting the frame position, please make sure it doesn't exceed the range of silk screen printing on the inner crossbar.
7 8
0 m n 35 3max 5 max) 30 25 20 15 0 5 5 1 15 2 0
Adjusting the Frame
Note: The depth of the mounting holes should be over 10mm and the diameter shou d be less than 3mm.
9 10
Use a drill to make mounting ho es on the backside of the tabletop through the 8 mounting ho es on the side brackets
S-I Drill
Ret ghten al the hex head screws to finish the adjustment.
Drilling Mounting Holes
• F x the lifting column with crossbar us ng 4 screws w th the Allen wrench .
• Insert one lift ng column nto one end of the crossbar w th the head of the lift ng column facing inward Make sure the mount ng holes on the lifting co umn completely a ign with the screw ho es on the crossbar
C S-A S-I
• Fix the foot us ng 4 screws with the Allen wrench .
• Repeat the same process to assemble the other l fting column
S-I
SD -B S-I
• Repeat the same process to assemb e the other foot.
11 12 C S-A
D S-B S-I
Assembling the Lifting Columns Assembling the Feet
• Place the foot on the bottom of the lifting co umn. A ign the mounting ho es on the foot with the screw ho es on the lifting co umn.
• Insert the in the port markedpower plug "AC"G
At least two people are required when turning over the desk frame. If on y one person turns over the desk frame, serious bodily injur es might occur.
• Al gn the mounting holes on the fixing plate with the screw holes as shown
• Please make sure the slot on the control box is fac ng upward. There is no corresponding relation between the motor ports and the l ft ng columns.
AHSC
• Connect the contro ler cord to the port marked "HS"
J
• Attach the fixing plate on the center of the crossbar with 2 screws us ng a Phillips screwdriver.
CAUTION
• Connect the cords, control box and motors.
Note: The arrow on the fixing plate ndicates the d rection of slid ng n the contro box. Fo low the direct on of the arrow to mount the contro box in the next step
The f x ng p ate can be attached to e ther of the right s de and the eft side.
Assembling the Fixing Plate Attaching the Control Box
ORE S-E
E S-E G
• Connect the two motor cords to the two ports marked "M1" and "M2" (one on each s de of the contro box)
Note:
• The picture of the controller s for your reference only. Actual product may vary F
Phillips Screwdriver
13 14 F J
• Turn over the desk frame with the crossbar facing up
S-F H I Phillips Screwdriver
• Fol ow the direction of the arrow to mount the control box • Sl de the control box to the center of fixing plate.
• holes on the cab e management tray.
A ign the mount ng holes on the tray hangers with the screw H S-F I
1
2 15 16
The arrow on the f xing plate indicates the direction of slid ng n the contro box.
• Assemb e the tray hangers to the cable management tray with 4 screws from below using a Phillips screwdriver
Assembling the Cable Management Tray
Hang the cable management tray on the crossbar as shown.
Assembling the Desktop
S-H
17 18
Tighten the knobs on the tray hangers S-H
Attach the anti-vibration pads to the surface of the crossbar on the ten posit ons as shown. S-H
S-D S-D Drill
S-C
Phillips Screwdriver
• Attach the contro ler to the desktop with 2 screws us ng a driller.
21
S-G
• St ck the adhesive cable clip under desk to organize cords. S-G
19 20
S-C
• Al gn the prev ously drilled screw holes with the mount ng holes on the crossbar. Insert and tighten the 4 screws from below • Repeat the same process to assemble the other side of the desktop.
You can now use the sit-stand desk
Connect the desk to power.
Note: We have another manual of the dig tal controller for detailed nstruction. Please check the Digital Control Panel For Electric Height Adjustab e Desk User Gu de.
Level Adjustment
Tip: Use a bubble level to check if the desktop is even.
21 22
Height Adjustment
Bubble Level
M07-23D M07-23R
There are two ad ustable foot pads under each foot. If the f oor isn t even, simply turn the pad to adjust the evel to make the desk stable.