Vehiclefault Codes

Vehiclefault Codes

40001342.00-en

Code Definition Possible Steps for repair

1310 yellow Hydraulic filter blocked Change filter 1311 yellow Engine airfilter blocked Change filter 1312 yellow Hydraulic oil temperature above normal 1313 red Hydraulic oil temperature to high 1314 yellow Transmission oil temperature above normal 1315 red Transmission oil temperature to high Stop machine operations Run engine at 1500 rpm Check fan operation Check cooling core for clogs

1316 red Brake pressure too low Stop machine operations Run engine at 1500 rpm Check brake system pressure Check brake system for leaks

1317 red Steering pressure too low

1318 yellow Engine coolant temperature above normal

1319 red Engine coolant temperature highcertical Stop machine operations Run engine at 1500 rpm Check steering system for operation Check steering system for leaks Stop machine operations Run engine at 1500 rpm Check fan operation Check radiator core for clogs

1320 red Engine oil pressure too low

1321 yellow Engine oil pressure below normal Stop machine operations Check engine oil level Check pressure sender unit

1322 yellow Engine oil pressure above normal Check engine oil for proper type Check pressure sender unit

1323 yellow Battery voltage low 1324 yellow Battery voltage high Check charging system

1325 red Oil temperature too high

Stop machine operations Run engine at 1500 rpm Check sending unit 1326 yellow Coolant level low Fill radiator level 1327 yellow Moved during accelerated idle No inf ormation available at ti me of print 1328 yellow Moving when shif ting too low idle No informat ion available at ti me of print

1331 red Recharging system voltage too low

Set vehicle mode Check charging system 1332 red Water contamination in fuel Replace/change the fuel pre-filter

Code Definition Possible Steps for repair

1333 red Engine overspeed Check engine speeds 1334 red Intake manif old temperature high critical Check for defective or clogged after cooler

1335 red Brake pressure too low

1.Stop machine operations 2.Run engine at 1500 rpm 3.Check brake system pressure 4.Check brake system for leaks 1341 yellow Check Emergency Steering pump Check Emergency Steering pump

Engine Fault Codes

40001343.00-en

Code Definition Possible Steps for repair 3000 red unknown ECM error code Possible Steps For Repair

3001

red Foot throttle sensor signal not plausible pressure sensor signal

3002 red Foot throttle sensor signal above range max.

3003 red Foot throttle sensor signal below range min. Idle switch defect or wiring of idle switch broken or accelerator pedal defect . Check wiring, replace idle switch or replace accelerator pedal.. Short circuit in wiring or in accelerator pedal. Check wiring or replace accelerator pedal Short circuit in wiring or in accelerator pedal. Check wiring or replace accelerator pedal

3004 red Foot throttle sensor max. no signal Check wiring or replace accelerator pedal

3006 yellow Coolant temperature sensor signal not plausible

3007 yellow Coolant temperature sensor signal above range max. 3008 yellow Coolant temperature sensor signal below range min.

3009 yellow Coolant temperature sensor null (via CAN)

3010 yellow Air Intake Temperature Sensor - Signal Above Range Max. 3011 yellow Air Intake Temperature Sensor - Signal Above Range Min. 3012 yellow Air Intake Temperature Sensor - (via CAN) No Signal 3013 yellow Main Relay 1 (High Pressure Pump) short to Bat. 3014 yellow Grid Heater/Battery Switch Relay Short-circuit to Ground

3015 yellow Fuel temperature signal above range max.

3016 yellow Fuel temperature signal below range min.

3019 yellow Boost pressure sensor signal range mass,

3021 yellow Boost pressure sensor null (via CAN) See OTS (Oil Temperature Sensor) plausibility check fault 3033

Sensor defective or short circuit to external source. Check wiring or replace sensor. Sensor defective or short circuit to ground. Check wiring or replace sensor. No CAN plausibility check performed, restart system, if problem reoccurs. Check wiring or replace sensor.

Sensor defective or short circuit to external source. Check wiring or replace sensor. Sensor defective or short circuit to ground. Check wiring or replace sensor. Sensor defective or short circuit to external source. Check wiring or replace sensor. No CAN plausibility check performed, restart system, if problem reoccurs. Check wiring or replace sensor.

Code Definition Possible Steps for repair

3022 yellow Boost pressure sensor signal not plausible Difference of ambient and boost pressure is out of range Check wiring or replace sensor.

3023 yellow Atmospheric pressure sensor signal not plausible 3024 yellow Atmospheric pressure sensor signal above range max. 3025 yellow Atmospheric pressure sensor signal below range min.

3028 yellow Oil pressure sensor pressure too low

3029 yellow Oil pressure sensor short-circuit to battery

3030 yellow Oil pressure sensor short-circuit to ground.

3031 yellow Oil pressure sensor ADC conversion error

3032 yellow Oil pressure sensor pressure too high Ambient pressure sensor inside ECU is defect . Replace ECU (not necessary if never running in high altitude and if turbocharger is without VGT)

Inaccurate oil pressure sensor or defect (e.g. too low oil level, leakage) in the oil system, Check oil pressure sensor for accuracy and check oil system Sensor defective or short circuit to external source Check wiring or replace sensor. Sensor defective or short circuit to ground. Check wiring or replace sensor. Inaccurate oil pressure sensor or defect (e.g. blocked piping) in the oil system. Check oil pressure sensor for accuracy and check oil system Inaccurate oil or coolant temperature sensors or insufficient oil or coolant recirculation (low coolant level etc.). Check oil and coolant temperature sensor for accuracy and check oil and coolant system for proper functioning.

3033 yellow Oil temperature sensor signal not plausible

3034 yellow Oil temperature sensor signal above range max.

3035 yellow Oil temperature sensor signal below range min. Inaccurate oil or coolant temperature sensors or insufficient oil or coolant recirculation (low cool ant level etc.). Check oil and coolant temperature sensor for accuracy and check oil and coolant system for proper functioning. Sensor defective or short circuit to external source. Check wiring or replace sensor. Sensor defective or short circuit to external source. Check wiring or replace sensor.

3036 yellow Oil temperature sensor signal CAN transmission disturbed

No CAN plausibility check performed, restart system, if problem reoccurs. Check wiring or replace sensor. 3037 yellow Boost pressure sensor signal low Sensor defective or short circuit on ground. Check wiring or replace sensor. 3043 yellow Vehicle speed sensing hardware conversation error

3046 yellow Vehicle speed sensing signal not plausible

3051 yellow Battery voltage to ECM too high Alternator voltage governor defect. Replace alternator governor device or alternator.

Code Definition Possible Steps for repair

3052 yellow Battery voltage to ECM too low

3060 yellow Cylinder 1 unclassified error in injector

3061 yellow Cylinder 1 injector cable short circuit low side to battery

3062 yellow Cylinder 1 signal low Battery defect, alternator defect, wiring problem (too high resistance) or ECU defect . Occurrence possible during cold start. Replace battery or alternation, Check ECU and wiring Depending on the pattern, various reasons can cause the defect, internal ECU problems also, possible. Check the wiring and the injection signals, replace ECU Short circuit in wiring with external source. Check the wiring or replace injector Check the wiring and the injection signals, replace ECU

3063 yellow Cylinder 1 short -circuit high side to ground Defective coil of injector. Check the wiring and replace injector

3064 yellow Cylinder 5 unclassified error in injector

3065 yellow Cylinder 5 injector cable short –circuit low side to battery

3066 yellow Cylinder 5 signal low

3067 yellow Cylinder 5 short-circuit high side to ground Depending on the pattern various reasons can cause the defect, internal ECU problems also possible Check the wiring and the injection signals, replace ECU Short circuit in wiring with external source. Check the wiring or replace injector Check the wiring and the injection signals, replace ECU. Defective coil of injector. Check the wiring and replace injector

3068 yellow Cylinder 3 unclassified error in injector Depending on the pattern various reasons can cause the defect, internal ECU problems also possible Check the wiring and the injection signals, replace ECU

3069 yellow Cylinder 3 injector cable short –circuit low side to battery

Short circuit in wiring with external source. Check the wiring or replace injector 3070 yellow Cylinder 3 - Signal Low Check the wiring and the injection signal replace ECU.

3071 yellow Cylinder 3 - Injector Cable Shortcircuit (High Side to Low Side) Defective coil of injector. Check the wiring and replace injector

3072 yellow Cylinder 6 - Unclassifiable Error in Injector Depending on the pattern, various reasons can cause the defect internal ECU problems also, possible. Check the wiring and the injection signals, replace ECU

3073 yellow Cylinder 6 - Injector Cable Shortcircuit (Low Side to Battery)

Short circuit in wiring with external source. Check the wiring or replace injector 3074 yellow Cylinder 6 - Signal Low Check the wiring and the injection signals, replace ECU.

3075 yellow Cylinder 6 - Injector Cable Shortcircuit (High Side to Low Side) Defective coil of injector. Check the wiring and replace injector

Code Definition Possible Steps for repair

3076 yellow Cylinder 2 - Unclassifiable Error in Injector Depending on the pattern, various reasons can cause the defect , possible internal ECU problems also Check the wiring and the injection signals, replace ECU

3077 yellow Cylinder 2 - Injector Cable Shortcircuit (Low Side to Battery)

Short circuit in wiring with external source. Check the wiring or replace injector 3078 yellow Cylinder 2 - Signal Low Check the wiring and the injection signals, replace ECU.

3079 yellow Cylinder 2 - Injector Cable Shortcircuit (High Side to Low Side) Defective coil of injector. Check the wiring and replace injector

3080 yellow Cylinder 4 - Unclassifiable Error in Injector

3081 yellow Cylinder 4 - Injector Cable Shortcircuit (Low Side to Battery)

3082 yellow Cylinder 4 - Signal Low

3083 yellow Cylinder 4 - Injector Cable Shortcircuit (High Side to Low Side)

3088 yellow Crankshaft Sensor - Lost Synchronisation

3089 yellow Crankshaft Sensor - Defective

3090 yellow Camshaft Sensor - Lost Phase

3091 yellow Camshaft Sensor - Phase Synchronisation Failure

3093 yellow Offset Between Camshaft and Crankshaft - Outside Boundaries

3095 yellow Operating with Camshaft Sensor Only Depending on the pattern, various reasons cancause the defect, internal ECU problems also possible Check the wiring and the injection signals, replace ECU (evaluate raw signals) Short circuit in wiring with external source. Check the wiring or replace injector Check the wiring and the injection signals, replace ECU. Defective coil of injector. Check the wiring and replace injector Signal interrupted do to wiring problem, defective or incorrectly installed crankshaft speed sensor. Check wiring, sensor installation and proper functioning of crankshaft sensor (evaluate raw) Check wiring, sensor installation and proper functioning of crankshaft sensor (evaluate raw signals) Signal interrupted do to wiring problem, defective or incorrectly installed camshaft phase sensor. Check wiring, sensor installation and proper functioning of camshaft phase sensor (evaluate raw signals) Check wiring, sensor installation and proper functioning of camshaft phase sensor (evaluate raw signals). Signal interrupted do to wiring problem, defective or incorrectly installed camshaft or crankshaft sensor. Check wiring, sensor installations and proper functioning of camshaft and crankshaft sensors (evaluate raw signals) Check wiring, sensor installation and proper functioning of crankshaft sensor (evaluated raw signals)

Code Definition Possible Steps for repair

3102 red Rail Pressure Sensor CP3 - Signal Below Range Min. short circuit of wiring to ground or defective pressure sensor. Check wiring and proper functioning of rail pressure sensor

3104 red Rail Pressure Relief Valve - Open

3105 red Rail Pressure Relief Valve - Pressure Shock Requested Defective rail pressure sensor, defect in other injection relevant component. Check rail pressure sensor for plausible values, ensure proper functioning of the injection components PRV dose not open once the pressure limit is reached: Mechanical defect or wrong application parameter. Check application value of maximum rail pressure, check functioning of the PRV

3106 red Rail Pressure Relief Valve - Did Not Open After Pressure Shock

3107 yellow Metering Unit Output - Shortcircuit to Battery on Low side

3108 yellow Metering Unit - Short-circuit to Ground

3110 red Rail Pressure Sensor Offset Monitoring - Signal Above Range Max.

3111 red Rail Pressure Sensor Offset Monitoring - Signal Below Range Min.

3112 red Rail Pressure Sensor CP3 - Signal Above Range Max. PRV does not open even after pressure shock: Stuck PRV or wrong application parameter. Check application value of maxi mum rail pressure, check functioning of the PRV Short circuit between wiring and external source, or in relay. Check wiring or replace relay.

Check wiring

Rail pressure sensor inaccurate. Ensure correct wiring and proper functioning of rail pressure sensor, replace sensor Rail pressure sensor inaccurate. Ensure correct wiring and proper functioning of rail pressure sensor, replace sensor Short circuit of wiring to external source or defective pressure sensor, rail pressure overshoot. Check wiring and proper functioning of rail pressure sensor

3113 yellow Main Relay 1 (High Pressure Pump) short to Bat. Short circuit of main relay to external source or defective main relay. Check the wiring connecting the battery to the EDC or replace main relay

3114 yellow Grid Heater/Battery Switch Relay Short-circuit to Ground Short circuit to ground of main relay or defective main relay. Check the wiring connecting the battery to the EDC or replace main relay

3118 yellow ECM 12V Sensor Supply Voltage High 3119 yellow ECM 12V Sensor Supply Voltage Low Ambient pressure sensor inside ECU is defective. Replace ECU (not necessary if never running in high altitude and if turbocharger without VGT)

Code Definition Possible Steps for repair

3131 yellow Grid Heater Always Switched On Short circuit to ground of grid heater. Check gridheater switch and replace it 3137 yellow Metering Unit - Open Load Broken or disconnected wiring or defective relay. Check of wiring or replace relay

3138 yellow Metering Unit - Signal Not Plausible Defective wiring, ECU, power stage or metering unit. Check wiring, ECU, power stage and metering unit

3141 yellow Setpoint of Fuel Volume Flow Through Metering Unit is Lower than Calculated Limit

3147 yellow Oil Temperature Sensor - Signal Above Normal Range 3154 yellow Grid Heater Relay - Short-circuit to Battery High pressure system: Rail pressure sensor inaccurate, high pressure pump defective. Low pressure system: Metering unit reflux too low. Check for defects according to failure list Check oil temperature sensor for accuracy and check oil system. Short circuit of wiring to external source or inside relay Check wiring or replace relay

3155 yellow Grid Heater Relay - Short-circuit to Ground

Short circuit of wiring to ground or inside relay. Check wiring or replace relay 3156 yellow Grid Heater Relay - No Load Broken or disconnected wiring or defective relay. Check wiring or replace relay 3161 yellow Fan Actuator - Signal Low

3171 red Rail Pressure Governor Deviation Exceeded Max. Limit with Fuel Delivery Quantity on Limit High pressure side: Leakage in high pressure section injection nozzle stuck in open position, worn high pressure pump, worn injector, leaking pressure relieve valve Low pressure side: Pressure before gear pump too low, gear pump output too low (fuel filter clogged, leakage in low pressure side).

3172 red Rail Pressure Governor Deviation Exceeded Min. Limit with Fuel Delivery Quantity on Limit

Metering unit stuck in open position, zerodelivery throttle clogged, metering unit without power due to electrical error. Low pressure side: Pressure before gear pump too high (e.g. by pressure relieve valve), pressure after zerodelivery throttle too high. 3173 Rail Pressure Governor Deviation Below Min. Limit for Speed See fault 3171 3174 red Rail Pressure Governor Deviation Exceeded Max. Limit See fault 3172

3175 yellow Rail Pressure Drop Rate is Higher than Expected

3176 yellow Fuel Delivery Exceeded Threshold for Pressure in Overrun Mode Leakage in the high pressure section, injection nozzle stuck in open position, worn high pressure pump, worn injector, leaking pressure relieve valve, injector reflux too high. High pressure system: Leakage in the high pressure section, injection nozzle stuck in open position, worn or defective high pressure pump, worn injector, leaking pressure relieve valve. Low pressure system: "Zero delivery" is not active in metering unit (excessive leakage in metering unit) Check for defects according to failure list .

Code Definition Possible Steps for repair

3178 yellow Timeout of CAN Message BC2EDC1 3179 yellow Timeout of CAN Message BC2EDC2 Defective CAN controller of Vehicle Control Module, under voltage of VCM, missing VCM, CAN cable connecting the VCM is disconnected or broken. Short circuit in wiring. Check presence and correct connect ion of the VCM to the network Check correct functioning of the VCM CAN controller and its voltage supply. Check wiring.

3180 yellow Timeout of CAN Message VCM2EDC Defective CAN controller of Vehicle Control Module, under voltage of VCM, missing VCM, CAN cable connecting the VCM is disconnected or broken. Short circuit in wiring. Check presence and correct connect ion of the VCM to the network Check correct functioning of the VCM CAN controller and its voltage supply. Check wiring

3188 yellow Cylinder1 - Open Load 3192 yellow Cylinder2 - Open Load 3196 yellow Cylinder3 - Open Load 3200 yellow Cylinder4 - Open Load 3204 yellow Cylinder5 - Open Load 3208 yellow Cylinder6 - Open Load 3210 yellow Bank1 - General Short-circuit on Injection Cable Broken wire or disconnection of wiring or inside injector Check the wiring or replace injector.

Short circuit of high-side to battery or ground. Check the wiring or replace injector.

3211 yellow Bank1 - Injection Cable Shortcircuit Low Side to Ground

Short circuit of low-side to ground in injector cable Check the wiring or replace injector. 3212 yellow Bank 1 no signal Check the wiring

3213 yellow Bank1 - Unclassifiable Error Depending on the pattern, various reasons can cause the defect, internal ECU problem. Check the wiring and the injection signals, replace ECU

3218 yellow Bank2 - General Short-circuit on Injection Cable Short circuit of high-side to battery or ground. Check the wiring or replace injector.

3219 yellow Bank2 - Injection Cable Shortcircuit Low Side to Ground

Short circuit of low-side t o ground in inject or cable Check the wiring or replace injector. 3220 yellow Bank2 - No Signal Check the wiring

3221 yellow Bank2 - Unclassifiable Error Depending on the pattern, various reasons can cause the defect, internal ECU problem. Check the wiring and the injection signals, replace ECU.

3227 yellow Injection Processor Error --> Stop Engine

3228 yellow Injection Processor Error --> Stop Engine

3229 yellow Injection Processor Error --> Stop Engine Clock error or interruption of the power supply voltage. Check the power supply or replace ECU if problem reoccurs. Defective ECU, reset ECU. if no recovery, replace ECU. Internal failure of ECU or 'TESTMODE' takes too long. Check 'TESTMODE' parameters or replace ECU if problem reoccurs

Code Definition Possible Steps for repair

3230 yellow Injection Processor Error --> Stop Engine Defective SPI-bus participant, timing problem due to software bug. Replace ECU if problem reoccurs (Send in ECU for investigation)

3231 yellow Injection Processor Error --> Stop Engine 3232 yellow Injection Processor Error --> Stop Engine 3233 yellow Injection Processor Error --> Stop Engine 3234 yellow Injection Processor Error --> Stop Engine Defective ECU. Replace ECU if problem reoccurs

3238 red Communication Error of CJ940 Processor Electric disturbances, internal defect of the ECU leading to a SPI bus communication error. Replace ECU if failure remains present

3242 red Recovery which is locked 3243 red Recovery which is suppressed

3244 red Recovery which is visible

3245 yellow Commence. supervision Watchdog/Contr.-Flag Electronic disturbances, various hardware defects (ECU internal) or configuration problems. Analyse what error triggered the recovery (Readout label HWEMon_num Recovery and compare the value with the according table).If error occursedly repeat, reprogram EDC. If error remains, replace EDC. Defective monitoring module or CPU (e.g. impaired functioning of the CPU clock)of the EDC. Disturbed SPI -Bus. If error exists only temporary (i.e.injection reoccurs) error can be ignored and error deleted in the fault memory. In case of a permanent error the injection remains blocked and the ECU has to be replaced

3246 yellow Redundant shutoff paths during initial. / ECU HW Watch dog switch off path defect. If failure remains after ECU initialisation: replace ECU

3247 yellow Redundant shutoff paths during initial.

3248 yellow Redundant shutoff paths during initial. Electronic disturbances, internal ECU problem. If failure remains after ECU initialisation: replace ECU.

3253 yellow Error status ADC monitoring 3254 yellow Error status ADC monitoring 3255 yellow Error status ADC monitoring 3256 yellow Error status ADC monitoring Buffer overrun

Code Definition Possible Steps for repair

3258 yellow Short-circuit to Battery at High Side Power Stage Short circuit of wiring to external source or inside relay. Check wiring or replace relay

3259 yellow Short-circuit to Ground at High Side Power Stage 3260 yellow Open Load at Low Side Power Stage

3261 yellow

Short-circuit to Battery or Excessive Temperature at Low Side Power Stage 3262 yellow Short-circuit to Ground at Low Side Power Stage Short circuit of wiring to ground or inside relay. Check of wiring or replace relay Broken or disconnected wiring or defective relay. Check wiring or replace relay

Short circuit of wiring to external source or inside relay. Check wiring or replace relay

Short circuit of wiring to ground or inside relay. Check wiring or replace relay

3265 red Energising time exceeds limit of overrun monitoring

3266 red Plausibility Error in Engine Speed Check

3278 red Supply voltage CJ940 upper limit

3279 red Supply voltage CJ940 lower limit

3280 yellow Sensor Supply Voltage 1 - High

3281 yellow Sensor Supply Voltage 1 - Low

3283 yellow Sensor Supply Voltage 2 - High

3284 yellow Sensor Supply Voltage 2 - Low Electronic disturbances, requested torque increase via tester, wrong application of inject ion relevant parameters, defective ECU. Check injection relevant application, if failure persists replace ECU Electronic disturbances, internal ECU problem. If failure persists after reinstallation replace ECU Excessive voltage supply of a CJ940 component : High battery voltage, defective wiring, internal defect of the EDC. Check the battery for correct voltage supply, check wiring. If defect remains replace EDC (internal defect). Insufficient voltage supply of a CJ940 component: Low battery voltage, defective wiring, internal defect of the EDC. Check the battery for sufficient volt age supply, check wiring. If defect remains replace EDC (internal defect). Excessive battery voltage, defect in wiring harness, electrical failure in connected sensors or in the EDC. Check battery voltage, check wiring for correct voltage supply of the sensor and the EDC, replace EDC Insufficient battery voltage, defect in wiring harness, electrical failure connected sensors or in the EDC. Check battery voltage, check wiring for correct voltage supply of the sensor and the EDC, replace EDC Excessive battery voltage, defect in wiring harness electrical failure in connected sensors or in the EDC. Check battery voltage, check wiring for correct voltage supply of the sensor and the EDC, replace EDC Insufficient battery voltage, defect in wiring harness, electrical failure connected sensors or in the EDC. Check battery voltage, check wiring for correct voltage supply of the sensor and the EDC, replace EDC

Code Definition Possible Steps for repair

3285 yellow Sensor Supply Voltage 3 - High Excessive battery voltage, defect in wiring harness electrical failure in connected sensors or in the EDC. Check battery voltage, check wiring for correct voltage supply of the sensor and the EDC, replace EDC

3286 yellow Sensor Supply Voltage 3 - Low

3290 yellow Turbo Compound Monitoring - Signal Not Plausible 3315 yellow Minimum Number of Injections Not Reached - Stop Engine 3316 yellow Minimum Number of Injections Not Reached - Stop Engine 3317 yellow Minimum Number of Injections Not Reached - Stop Engine 3318 yellow Minimum Number of Injections Not Reached - Stop Engine 3363 yellow Ambient air pressure sensor signal not plausible 3856 yellow Coolant Temperature does not rise as expected Insufficient battery voltage, defect in wiring harness, electrical failure connected sensors or in the EDC. Check battery voltage, check wiring for correct voltage supply of the sensor and the EDC, replace EDC

Call Service

„Motor Stop“ Service rufen

Call Service

Call Service