GENERAL INFORMA TION
CLEANING Clean all metal parts except bearings, in a suitable cleaning solvent steam cleaning. not use caustic soda for steam cleaning. After cleaning, dry and put oil all parts. Clean oil passages with compressed air . Clean bearings in a suitable cleaning solvent, dry the bearings completely and put oil the bearings. INSPECTION Check all parts when the parts are disassembled. Replace all parts that have wear damage. Small scoring grooves can removed with a hone crocus cloth. Complete a visual inspection for indications wear , pitting and the replacement parts necessary prevent early failures. BEARINGS Check bearings for easy action. bearings have a loose fit rough action replace the bearing. W ash bearings with a suitable cleaning solvent and permit air dry .
NOT Y BEARINGS WITH COMPRESSED AIR. NEEDLE BEARINGS Before you press needle bearings in a bore always remove any metal protrusions in the bore edge the bore. Before you press bearings into position put petroleum jelly the inside and outside diameter the bearings. GEARS Check all gears for wear and damage. Replace gears that have wear damage. Oil seals, O- rings and gaskets. Always install new oil seals, O- rings and gaskets. Put petroleum jelly seals and Orings. SHAFTS Check all shafts that have wear damage. Check the bearing and oil seal surfaces the shafts for damage. SER VICE P AR Always install genuine Case service parts. When ordering refer the Parts Catalogue for the correct part number the genuine Case replacement items. Failures due the use other than genuine Case replacement parts are not covered warranty . LUBRICA TION Only use the oils and lubricants specified in the Operator ’s Service Manuals. Failures due the use non - specified oils and lubricants are not covered warranty .
Safety
This symbol means A TTENTION! BECOME ALER YOUR SAFETY INVOL VED. The message that follows the symbol contains important information about safety . Carefully read the message. Make sure you fully understand the causes possible injury death.
To prevent injury always follow the W arning, Caution and Danger notes in this section and throughout the manual. Put the warning tag shown below the key for the key switch when servicing repairing the machine. One warning tag is supplied with each machine. Additional tags are available from your service parts supplier .
W ARNING
Read the operator's manual familiarize yourself with the correct control functions.
W ARNING
Operate the machine and equipment controls from the seat position only . Any other method could result serious injury .
W ARNING
This a one man machine, riders allowed.
W ARNING Before starting engine, study Operator ’s Manual safety messages. Read all safety signs machine. Clear the area other persons. Learn and practice safe use controls before operating. your responsibility understand and follow manufacturers instructions machine operation, ser-
vice and observe pertinent laws and regulations. Operator's and Service Manuals may obtained from your CASE dealer .
W ARNING
you wear clothing that too loose not use the correct safety equipment for your job, you can injured. Always wear clothing that will not catch objects. Extra safety equipment that can required includes hard hat, safety shoes, ear protection, eye face protection, heavy gloves and reflector clothing.
W ARNING
When working the area the fan belt with the engine running, avoid loose clothing possible, and use extreme caution.
W ARNING
When doing checks and tests the equipment hydraulics, follow the procedures they are written.
NOT change the procedure.
W ARNING
When putting the hydraulic cylinders this machine through the necessary cycles check operation remove air from a circuit, make sure all people are out the way .
W ARNING
Use insulated gloves mittens when working with hot parts.
W ARNING
Lower all attachments the ground use stands safely support the attachments before you any maintenance service.
W ARNING
Pin sized and smaller streams hydraulic oil under pressure can penetrate the skin and result serious infection. hydraulic oil under pressure does penetrate the skin, seek medical treatment immediately . Maintain all hoses and tubes good condition. Make sure all connections are tight. Make a replacement any tube hose that damaged thought damaged.
NOT use your hand check for leaks, use a piece cardboard wood.
W ARNING
When removing hardened pins such a pivot pin, a hardened shaft, use a soft head (brass bronze) hammer use a driver made from brass bronze and a steel head hammer .
W ARNING
When using a hammer remove and install pivot pins separate parts using compressed air using a grinder , wear eye protection that completely encloses the eyes (approved goggles other approved eye protectors).
W ARNING
Use suitable floor (service) jacks chain hoist raise wheels tracks off the floor . Always block machine place with suitable safety stands.
W ARNING
When servicing repairing the machine, keep the shop floor and operator's compartment and steps free oil, water , grease, tools, etc. Use oil absorbing material and / shop cloths required. Use safe practices all times.
W ARNING
Some components this machine are very heavy . Use suitable lifting equipment additional help instructed this Service Manual.
W ARNING
Engine exhaust fumes can cause death. necessary start the engine a closed place, remove the exhaust fumes from the area with exhaust pipe extension. Open the doors and get outside air into the area.
W ARNING
When the battery electrolyte frozen, the battery can explode (1), you try charge the battery , (2), you try jump start and run the engine. To prevent the battery electrolyte from freezing, try keep the battery full charge. you not follow these instructions, you others the area can injured.
