Tæknilegar Upplýsingar fyrir X-FCP Checker Plate Fastener

X-FCP DATA SHEET

Checker plate fastening system

April 2021

X-FCP

X-FCP Checker plate fastening system Product data Dimensions X-FCP-R 5/10

1

Material specifications See fastener selection for more details.

X-FCP-F 5/10

1

Recommended fastening tools

• See fastener program in the next pages.

HILTI

1

HILTI

2

10

2

1,25

10 o 45

o 45

Approvals LR: X-FCP ABS, LR: X-FCP-R ABS: X-FCP-F • N ot all information presented in this product data sheet might be subject to ­approval / certificate content. Please refer to approval / certificate for further information.

X-CRM8-15-12 FP10 Ø8 [0.315"]

X-ST-GR M8/5 P8

ɿ8

o 10

9 12 [0.354"] [0.472"] 25 [0.894"]

9

Lg

12.5

12.5 25

[0.315"]

30

Ø8

X-ST-GR M8/10 P8

X-CRM8-9-12 FP10

X-CRM8-15-12 P8 M8 o 4

ૃ

.

o8

M8

ૃ 14 12 [0.551"] [0.472"] 30 [1.181"]

04/2021

X-CRM8-9-12 P8 M8 ɿ4

M8 o 4

M8

X-FCP Sealing ring

www.hilti.group

Lg

12.5 30

2

X-FCP Application Checker plate

Application areas for X-FCP system X-FCP-R • Marine, offshore, petrochemical, caloric (coal, oil) power plants, etc.

• Not for use in automobile tunnels, swimming pools or similar environments.

X-FCP-F • Indoors, mildly corrosive environment, or for limited lifetime use.

• Not for use in marine atmosphere or in heavily polluted environment.

Sealing ring • Drip-through of water/oil needs to be prevented.

Performance data Recommended resistance under tension load Nrec = 1.8 [kN]

• Limited by the strength of the X-CRM8 and X-ST-GR threaded stud.

• Recommended loads are valid for fastenings of steel and aluminium with 20 mm ­pre-drilling.

• X-FCP-F and X-FCP-R are not intended for shear loading.

Application recommendation Fastened material thickness

X-CRM8 , X-ST-GR

Thickness of checker plates: tI ≅ 5.0–13.0 mm

tII

Base material thickness

Steel thickness: tII ≥ 6 mm

3 04/2021 www.hilti.group

X-FCP Fastener positioning in base material X-CRM8, X-ST-GR c

c

s

s

Edge distances: c ≥ 15 mm Spacing: s ≥ 15 mm

Application limits for X-CRM8 DX 76, DX 76 PTR Steel thickness, tII [mm]

20

tII ≥ 6 mm

18 16

2

14 12 10

1

① Fastener: X-CRM8-__-12 FP10 / Tool type: DX 76 (impact) ② Fastener: X-CRM8-__-12 FP10 / Tool type: DX 76 (co-acting)

8 6

S235Jxx S275Jxx

S355Jxx 450 500 550 600 650 Steel strength, Rm [N/mm2]

400

700

DX 6, DX 5, DX 460 Steel thickness, tII [mm]

20

tII ≥ 6 mm

18 16

2

14 12 10

1

① Fastener: Tool type: ② Fastener: Tool type:

X-CRM8-__-12 P8 / DX 6, DX 5 (impact), DX 460 X-CRM8-__-12 P8 / DX 5 (co-acting), DX 460

8 6

400

S235Jxx S275Jxx

S355Jxx 450 500 550 600 650 Steel strength, Rm [N/mm2]

700

• For co-acting operation push the fastener all the way back against the piston with a ramrod.

04/2021

www.hilti.group

4

X-FCP Application limits for X-ST-GR Tool type: DX 6, DX 5, DX 460

Tool type: DX 76 PTR

6WHHO WKLFNQHVV W,, >PP@

6WHHO WKLFNQHVV W,, >PP@

6WHHO VWUHQJWK 5P >1 PP @

6WHHO VWUHQJWK 5P >1 PP @

System recommendation • For more details, please refer to the chapter Accessories and consumables compatibility in the Direct Fastening Technology Manual (DFTM).

Threaded studs

13 16

Checker plate thickness Tools 9–13 mm DX 6, DX 5, DX 460, DX 76, DX 76 PTR 5– 8 mm DX 6, DX 5, DX 460, DX 76, DX 76 PTR 9–13 mm DX 6, DX 5, DX 460, DX 76 PTR 5– 8 mm DX 6, DX 5, DX 460, DX 76 PTR

11

5

Designation X-CRM8-15-12 X-CRM8-9-12 X-ST-GR M8/10 P8 X-ST-GR M8/5 P8

Cartridge selection and tool energy setting • Fastener setting information (e.g. cartridge recommendation, tool power ­level ­adjustment, base material properties and fastend material p ­ roperties) and ­installation information (e.g. quality assurance) are part of the corresponding ­product data sheet for fastener.

• Tool power level adjustment by setting tests on site.

• Start tool energy selection with lowest recommended tool power level.

• Correct according requirement from chapter quality assurance.

5 04/2021 www.hilti.group

X-FCP Material specification and coatings X-FCP-R system

Material designation Coating

① Disk X5CrNiMo17122 none

② Screw X2CrNiMo17132 none

③ Sealing ring Neoprene, black

① Disk ST2K40 BK Duplex

② Screw 9SMnPb28 K Duplex

③ Sealing ring Neoprene, black

X-FCP-F system Material designation Coating

• D uplex: 480 h Salt spray test per DIN 50021 and 10 cycles Kesternich test per DIN 50018/2.0 (comparable to 45 µm HDG steel).

X-ST-GR Shank P558 (CrMnMo ally) none

Threaded sleeve A4 (AISI316) none

Material designation

Shank Stainless steel wire, CR 500 (A4 / AISI316)

Coating

none

Threaded sleeve X2CrNiMo17132 X5CrNiMo17122+2H (A4 / AISI316) none

Material designation Coating X-CRM8

04/2021

www.hilti.group

6

X-FCP Quality assurance Fastening inspection X-CRM8-9-12

X-CRM8-15-12

hNVS = 12.0–15.0 mm

hNVS = 17.0–20.0 mm

X-ST-GR

X-ST-GR M8/5 P8, hNVS = 12.0–15.0 mm X-ST-GR M8/10 P8, hNVS = 17.0–20.0 mm

Installation Plates must be ­­ pre-drilled or pre-punched

Tighten the disk

o 18-20 mm

Tightening tool: • Screwdriver with torque release coupling (TRC) • S-NSX 2.8 x 15 bit

SB 12

25

mm

25

mm

Tightening torque Trec = 5–8 Nm

T = 5 - 8 Nm

Hilti Torque Screwdriver setting SF 120-A TRC 5.5–7 SF 150-A TRC 8–9

Hilti Torque tool X-BT 1/4” 7 04/2021 www.hilti.group

X-FCP Fastener program

Item no. and description Designation X-FCP-R X-FCP-F

04/2021

Item no.

308860 308859

Description Checker plate Checker plate

www.hilti.group

8