Supplement To General Catalogue

SUPPLEMENT TO GENERAL CATALOGUE

www.ntl.at

Support material

DS090-3K „Sepp“ support base, 260 x 220 mm Genuine, modern alternative to a retort stand; Special aluminium profile (NTL rail base profile), silver anodised, two laterally-mounted rail claws, with clamp socket for holding round rods of 3-14 mm in diameter or square rods of up to 12.5 mm; powder-coated, with M8 fixing screw; height of clamp socket (inner): 50 mm surface area: 265 x 220 mm; weight: 383 g approx.

DS095-3K Boss head cross-pattern, demo 03 For mounting round rods up to a max. of D= 16mm, square rods up to a max. of s=12.5 mm, or plates up to a max. of 14mm; cross, parallel or T-connection possible; sturdy screws with rounded threaded ends ensure that the components are held very firmly in place;die-cast aluminium; 2 x M8 wing screws; dimensions: 68 x 36 x 36 mm (without screws)

C7415-4Z Beaker tongs

DS085-1R Round base with clamp socket, uni For simple set-ups; heavy metal base with clamp socket for mounting support rods from 3 mm to 14 mm or square rods up to 12.5 mm; powder-coated; M8 fixing screw; dimensions: D= 84 mm, H= 58 mm; weight: approx. 395 g

DS093-04 Sliding saddle „Sepp“, H = 40 mm For setting up and fixing to rail bases or support rails; Special aluminium profile (NTL rail profile), silver anodised, with clamp socket, for mounting support rods of 3-14 mm in diameter or square rods of up to s = 12.5 mm; powder-coated, with M8 fixing screw; height of clamp socket (inner): 50 mm dimensions: 54 x 35 x 70 mm Weight: approx. 97 g

DS103-4G „parallel“ rail support, H = 101 mm DS103-5G „normal“ rail support, H = 101 mm To mount stand rails, support material or devices which have an aluminium special profile sliding saddle attached.

Special aluminium profile mounted on saddle, green powder coated, with clamping screw.

For handling cylindrical containers (beakers, etc.) with hot or dangerous contents;Very robust forceps made of nickel-plated steel, with rubber-coated gripper arms Gripper width: 40 – 120 mm Forceps length: approx. 260 mm

C7601-3L Protective gloves „uni“, size 10 (large) C7601-3M Protective gloves „uni“, size 9 (medium) C7601-3S Protective gloves „uni“, size 8 (small) Good heat protection, high grip, snug fit, great mobility, breathable; made of seamless knitted backing material with latex coating on palms and underneath fingers symbol picture

1

C7230-1F Tripod, variable height For supporting thermal protection mesh, ceran plates or wire triangles; simple, quick adjustment allows the optimum height to be set for almost any burner; an embossed mm scale allows equal height adjustment of the feet;Ring material: stainless steelRing diameter = 120 mm Adjustable height: approx.

122 – 188 mm Weight: approx. 535 g

Digital scales with large weighing plates at bargain prices!

DM125-4A Digital scales 06, 500 / 0,01 g DM125-4C Digital scales 02, 2000 / 0.1 g Dimensions: Weighing plate: 100 x 100 mm Scale pan, small: 102 x 102 x 7 mm Scale pan, large: 127 x 106 x 20 mm Housing dimensions: 127 x 106 x 17 mm

• easy to use with 4 buttons • fast operation thanks to quick self-calibration after switching on • tare and zeroising function • switch between gram, ounce, grain and carat

• • • • • •

unit counter function automatic turn-off easily readable display with blue backlight digit height: 10 mm battery driven (2 x AAA batteries included) incl. two transparent scale pans (also serve as protective lids)

DT730-2P Pelton turbine demo, with generator To demonstrate the conversion of mechanical energy into electrical energy; Low friction blade wheel in acrylic glass housing, Axle with large drive wheel and drive belt to a fixed housing with generator and two 4 mm safety jacks, Side inlet opening for a water hose, Base plate with outlet opening, can be mounted on the tank using a DM340-2W drain connector. Blade wheel diameter = approx. 145 mm; dimensions: approx. 200 x 80 x 235 mm

2

DM347-1F Free-fall apparatus „Jumbo“

For measuring the fall time of a 60 mm wooden ball. The course of the experiment can be seen from a distance due to the size of the ball and the large collecting vessel, making it extremely effective yet still very easy to carry out.

• Robust metallic holder; two simultaneously adjustable trigger clamps enable optimal time triggering (without residual friction or residual magnetism) • 60 mm wooden ball with metal axle and position marking • Large collecting vessel made of impact-resistant PP; • Upper opening 270 x 165 mm; • Inlaid foam rubber-damped impact plate

Dimensions of collecting vessel: 300 x 200 x 130 mm

A timer is also required, e.g.: DM341-1T Timer for free-fall apparatus

The container plus lid acts as a storage option for the holder and timer.

3

Magnetically on door frames (metallic)

Magnetically on blackboard

Magnetically on mobile board

On normal stand

Set-up possibilities:

4

DM128-3C Stress- and strain balance 2000/0.1 g

Balance with external weighing beam, for measurementin any direction; digital scales with rapid calibration thanks to the tare function;easily readable with backlit display;battery-powered, with automatic shut-down;weighing sensor with hook and pressure sleeve,protected by a robust metal housing;can be mounted on support rods up to a diameter of 10 mm; measuring range: +/- 2000 g; resolution: 0.1 g; height of digits: 10 mm; battery-powered (2 x AAA batteries included); dimensions of the balance housing: 125 x 105 x 17 mm

The NTL traction and pressure balance...

measures traction...

5

‌ and pressure...

... in any position

Tuning forks

DW101-1A Tuning forks, set of 8, for resonance box Set of tuning forks with conical shaft, insertable into the DW100-1AR resonance box; Frequencies: c1 – 256 Hz, d1 – 288 Hz, e1 – 320 Hz, f1 – 341.3 Hz, g1 – 384 Hz, a1 – 426.6 Hz, h1 – 480 Hz, c2 – 520 Hz Length of the tuning forks: 165 to 210 mm Tuning forks can be stored in a cardboard box

DW100-1AR Resonance box for tuning forks To accept a 440 Hz tuning fork or the one in the DW101-1A set, to amplify the sound; Wooden resonance box, 4 soft buffers at the bottom, insert for accepting the 440 Hz tuning fork at the top; Dimensions (without insert): (175 x 95 x 53 mm)

DW103-3S Tuning fork 2000 Hz, with wooden handle The Doppler effect can be made “audible” by rapidly turning the struck tuning fork on a cord; Chrome-plated steel tuning fork, frequency printed on fork, with wooden handle Total length: approx. 220 mm

DW121-1S Tuning fork with stylus 02, with variable frequency To visualise and record vibrations; large-scale model of a tuning fork including a holder for pencils,clamping weights to change or adjust the frequency, with handle,delivered with a pencil, Frequency: approx. 2.4 – 4 Hz

The frequency can be changed by moving the clamping weights

6

DW401-2W Ripple tank for overhead projector

Optical, electromagnetic, sound and other wave phenomena are comparable with the way that waves propagate on the surface of water.

This ripple tank can be used to display such phenomena on a very large scale even in daylight with the help of an overhead projector.

Depending on the type of wave source used, one-point, two-point or plane waves can be generated.

By placing various objects in the water tank, experiments on reflection, refraction and diffraction can be demonstrated.

Supplied materials: Wave generator Motor with magnet ripple generator, continuously variable speed; battery-powered (9 V battery) or hollow jack for 12 V DC power supply; double-sided, easy-to-use fine height setting on both sides allows quick, optimum adjustment to water level; steel base Water tank Made of acrylic glass; outer perimeter with two rows of rubber bumpers to avoid reflection; 4 height-adjustable plastic feet Viewing area: 217 x 217 mm; dimensions: 257 x 257 mm

Accessories included: • 2 Rippler generators for concentric waves • 1 Ripple generator for plane waves • 1 Reflection plate, 170 mm • 2 Diffraction plates, 85 mm • 1 Diffraction plate, 25 mm • 1 Semi-circular reflection plate, 150 mm • 1 Object for refraction, 90 x 70 mm • 1 Spirit level • 1 Box with lid and storage space shaped for the apparatus

Why the NTL particle motion model?

• Low-cost • Easy to use • Large projection image

7

• Super-bright projection image • Compact storage

Ripple tank experiments:

• Propagation of various wave types (Huygens’ principle) • Diffraction at an edge • Diffraction at a single slit • Diffraction at a double slit • Interference of two circular waves

• • • •

Reflection from a planar mirror Reflection from a concave mirror Refraction of plane waves Doppler effect

Diffraction at a single slit

Interference of two circular waves

Doppler effect

Projection image size comparison 8

DM850-2T Particle motion apparatus for OHP

For model experiments on the topic „Matter - states and behaviour“ (particle movement) Glass chamber on metal plate, with motor-driven vibrating bar which sets small metal balls into motion.

An overhead projector can be used to make this movement large and bright, so the phenomena listed below are visible for the whole class.

Supply voltage: 1 - 12 V DC, continuously adjustable Dimensions: 270 x 270 x 50 mm Weight: approx. 500 g

Why the NTL particle motion model?

Scope of supply:

• • • •

Low-cost Easy to use Large projection image Super-bright projection image • Compact storage 9

- 300 steel balls, 3 mm - 4 steel balls, 5 mm - 4 slices of steel, aluminium, wood and polystyrene - 1 ring for osmosis - 1 magnet 10 x 50 mm - 1 pincers - 1 instruction manual

Experiments:

• Properties of particles in different states of aggregation (solid, liquid, gaseous) • Thermal movement of particles (Brownian molecular motion) • Temperature increase • Buoyancy in liquids

• • • • • •

Gas pressure Evaporation Condensation Diffusion Osmosis Dissolving a crystal in water

Buoyancy in liquids The small discs made of steel, aluminium, wood and Styrofoam are raised upwards in different ways by the momentum of the small balls

Condensation Particles in a hot liquid evaporate and condense on a cold plate

10

P2110-1W Gas cartridge with valve, 460 g Gas mixture (70% butane, 30% propane) in safety container with valve, as per standards EN 417 and UN 2037, this gas mixture allows a higher flame temperature than pure butane gas; through the valve with thread, the burner attachment P2112-1B can be screwed on and off as often as desired.

Diameter = 11 cm Height = 14.5 cm Net filling weight: 460 g

P2112-1B Burner attachement for gas cartridge Laboratory burner attachment with needle valve and continuous fine air adjustment by thread; Suitable for valve cartridges with thread (P2110-1V, P2110-1W) Height: approx. 7 cm

C4360-2L

Thermopistol infrared, -20 - +400° C

For contactless and therefore safe measurement of the surface temperature; Measuring range: -20 - +400° C (± 2° C)

-4 - +752° F (± 4° F) Resolution: 0.1° C Measuring interval: 0.5 s Display height: 11 mm • Distance / measurement point ratio: 12:1 • Fixed value emission: 0.95 • Laser sighting, laser power: <1 mW • Automatic shutdown after 8 seconds • Data hold function • Backlight • Battery level indicator • including 2 x 1.5 V batteries (LR03) • Dimensions: approx. 135 x 94 x 36 mm • Mass: approx. 146 g

11

P2621-1A Heat absorbing tubes, pair of For demonstrating the degree of absorption of thermal radiation as a function of surface colour.

Two aluminium tubes with flat bottom and rim, black and white coated; dimensions: D= 15 mm, L= 100 mm

P2621-1B Mounting bracket for heat absorbing tubes For inclined positioning of the two absorbing tubes with thermometers at an angle of 25 or 70째; material: stainless steel dimensions: approx.

80 x 60 x 135 mm

Additionally required: 2 x C7320-1D Stopper silicone, 12.5/18/27 mm, 1 hole 2 x P2220-1A Thermometer with graduated scale,

-10 - +110째C

Therefore a considerable difference in the temperature becomes visible after 5 minutes

To achieve an ideal angle of incidence of the heat source (sun), the tubes can be positioned at an angle of 25째 or 70째 by using the mounting bracket.

DT615-2A Heat radiator, infrared, 2 x 400 W Powerful infrared heat radiator with two heating levels, carrying handle and stand;Two quartz lamps each with 400 watts emit heat through concave mirrors (surface of 16 x 10 cm).

Selector switch for operating one or both emitters, carrying handle for easy operation and transport, with a built-in anti-tip switch in the stand (if the device tips over, this turns off the device).

Dimensions: 24 x 14 x 36 cm (L x W x H)

12

Very strong neodymium-iron-boron magnet, magnetised through height:

HMMAQ-026

Nd-Fe-B Magnet, 26 x 26 x 10 mm (raw)

HMMAR-012

Nd-Fe-B Magnet, D = 12 mm, H = 4 mm, nickel-plated

HMMAR-022

Nd-Fe-B Magnet, D = 22 mm, H = 10 mm, nickel-plated

HMMAR-T12

Nd-Fe-B Magnet, D = 12 mm, H = 2 mm, nickel-plated

DE422-1I Dip needle, 200 mm, demo To determine the angle of inclination of the field lines of the earth‘s magnetic field against the horizontal; very sensitive, fine-mounted magnetic needle, dark end pointing towards north (the needle is not painted as this would result in an uneven mass distribution and thus an inaccurate result); solid white back plate made of acrylic glass, with semicircular scale (2 x 0 - 90° in 1° increments); transparent, semi-circular front plate to protect the needle; with direction template and installation base; with handle: L = 30 mm, D = 10 mm; shock-proof packaging using a sturdy cardboard box; Length of magnetic needle: 200 mm Digit height on scale: 12 mm Dimensions (L x W x H) 284 x 21 x 312 mm

DE422-1D Magnetic needle 200 mm, demo To determine the north-south direction in a demo experiment; Magnetic steel needle with bearing cap; the half of the needle pointing towards north is dark, L = 200 mm, Box with 360° scale and identification of the direction of north; The DE300-1N bearing needle is required for rotatable mounting; this is not included in the scope of delivery.

13

DE424-1G Globe for geomagnetism, 200 mm

To illustrate the magnetic field around the Earth and to demonstrate inclination; Coloured political globe, made of robust plastic, labeled in English, rotatably mounted at the corresponding inclination, with sleeve for mounting a magnet 15x80 mm;D=200 mm; (Delivered without magnet) Additionally required: 1 x DE410-1L Bar magnet, AlNiCo, 15x80 mm 1 x P3410-2K Magnetic field sensor, large, “neo“

The inclination is caused by „feeling“ the magnetic field lines around the Earth itself.

No matter where you are on earth, a compass (magnet) is always aligned in the North/South direction

P3411-2A Globe for geomagnetism, 85 mm To illustrate the magnetic field around the Earth and to demonstrate inclination; Coloured political globe, made of robust plastic, labeled in English;the extended sleeve - for mounting a magnet 10x50 mm serves as a handle; D=85mm; (Delivered without magnet) Additionally required: 1 x P3410-1K Magnet, AlNiCo, D=10 mm,L=50 mm 1 x P3410-2C Magnetic field sensor SE

Put the magnet into the globe

The function of the compass will be crystal-clear

Also inclination will be explained by „feeling“ the magnetic field lines around the earth

14

DE522-1H High voltage experiments, set

This module enables unusually impressive experiments on electrostatics to be carried out in combination with a Wimshurst machine or a Van de Graaff generator.

Inhalt: DS085-1R DE521-4S DE522-1F P3911-3F DE522-1S DE522-3B DE522-4G DE532-3Z DE532-3K DE532-3M P3310-3R P3310-4A DE532-3P DE532-4G

d

15

• • • •

robustly designed equipment, stored in a device-shaped box impact-resistant plastic casing, with lid, delivery includes experiment manual

Storage: 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Round base with stand tube Insulating support Paper bush Needle on a plug Pointed wheel 02 Flash-board „NTL“ Set of chimes Capacitor plates with cylinder Sphere with metal surface Grains for copier-principle Connecting leads SE, 50 cm, black Connecting leads SE, 75 cm, red Pad of paper for copier-principle Liquid glue, pen Experiment manual

DE522-9E 1 Box insert electrostatics Demo, foam P7806-1G 1 Storage box II large, with lid Plan for storage of all components + 2 stickers This set can be used to carry out the following experiments: ESH 01 Spark discharge ESH 02 Point discharge ESH 03 Paper bush ESH 04 Flash-board ESH 05 Set of chimes ESH 06 Bouncing ball ESH 07 Principle of a copier ESH 08 Electrostatic filter ESH 09 Tip wind

Experiments

ESH 06

ESH 07

ESH 04

DE550-1W Thundercloud For demonstrating the discharge of a thundercloud on a house (with lightning conductors); large cloud-model; with 4 mm jack and carrying strap; dimensions: approx.. 320 x 150 mm

DE550-1A House with lightning conductor To describe experimentally the effect and function of a lightning conductor on a house; model of a house with translucent front; fluorescent tube on the inside to indicate the derivation of the charge; fluorescent tube on the outside with conductor-adapter for demonstrating the conduction of a lightning bolt; placed upright on isolated â&#x20AC;&#x153;meadowâ&#x20AC;? with grounding plug socket; dimensions: 200 x 90 x 310 mm

Lightning discharge from a cloud onto a house

16

DE312-1A Clip terminal for 1.5 V batteries, magnetic For tapping the voltage of all types of 1.5 V cells with 4 mm laboratory plugs (2 pcs. required for one cell); a strong neodymium magnet in a sturdy stainless steel plate attracts the pole of a battery, causing a very good electric contact; 4 mm socket for normal or safety lab plugs; two rubber feet on the neodymium magnet bases guarantee good, scratch-free footing on metal panels; Dimensions: 40 x 42 x 13 mm

A socket for 4 mm laboratory plugs at each end of the 1.5 V cell

P3130-7B Mains transformer 12 V AC / 22 VA Mains transformer for powering SE experiment light sources or an SE function generator; output voltage: 12 V AC / 22 VA; connecting lead with ON/OFF switch and two 4 mm safety plugs with retractable sleeve to prevent accidental touching (l = 180 cm approx.); voltage source: 230 V AC / 50 Hz; dimensions: approx. 81 x 56 x 48 mm

The long cable (aprrox. 180 cm) allows an electrical supply from the sidewall or from a wing on the ceiling

The switch in the cable feed enables safe and user-friendly handling of the the lamp when switching on and off.

Information about protection class: Due to the reinforced insulation, the power supply complies with the requirements of protection class II. Equipment that corresponds to protection class II has double insulation or reinforced insulation between the mains circuit and output voltage. This precaution is also called protective insulation II (protected electrical separation). Even if you have electroconductive surfaces, they are protected against contact with other voltage-carrying parts.

17

DE751-3A Oscilloscope, two-channel, 30 MHz, VGA Digital storage oscilloscope with LAN and VGA outlet; therefore a direct connection to a PC, TV or data projector is possible; Display: 8-inch colour TFT LCD, Resolution: 800 x 600

• • • • • •

Sampling rate : 250 MS/s; Input coupling : DC, AC, GND; Input impedance: 1 MOhm in parallel with 10 pF; Max. input voltage: 400 V; Voltage source: 100 - 240 V AC / 50 - 60 Hz; • Dimensions: 340 x 155 x 70 mm, • Weight: approx. 1.82 kg

Included: 2 Measurement leads 1 USB cable 1 Power supply unit 1 Experiment manual “Experiments with the Oscilloscope“ 1 Manual

The simple and quick connection with e.g. a TV enables optimisation of the demonstration in classes, measurement recordings are clearly visible

DE720-9S Sliding resistor 20 Ohm, 2 A Sliding resistor with an open housing, allowing easy observation of the position of the slider along the resistance coil; with 3 sockets for safety and normal cables with 4 mm connectors; Resistance: 20 ohms; load capacity: 2 A (higher for short periods), max. voltage 42 V, dimensions: approx. 150 x 65 x 40 mm

18

P3212-12 Multimeter analogue 12

Portable measuring device for voltage and current, DC and AC; also usable as a galvanometer.

AC/DC voltage ranges: 1 mV, 100 mV - 30 V AC/DC current ranges: 100 μA - 3 A and 10 A Arc scale length approx. 90 mm • 1 mV upper value range for measuring thermal voltage or induction without a preamplifier • All measuring ranges (even low current) available in AC • Exceptional frequency response (typically -1.5 db at 20 kHz) allowing direct measurement of resonant circuits • Large, easy-to-read mirrored scale with clear marking • Extremely accurate, typically 1.5% • Durable selection switch • 10 A range with separate input socket • Zero at midpoint may be selected by switch Dimensions: approx. 200 x 140 x 100 mm Weight: approx. 675 g

Electronic overload protection with indicator light in all measuring ranges (no more melting fuses!)

Transparent base with recessed handle to hold the device with one hand

19

P3212-2S Holder for multimeter analogue For vertical positioning of the new NTL Multimeter analog, thereby creating a small demo measuring instrument; Metal bracket, yellow powder-coated.

Dimensions: (142 x 55 x 87 mm)

P3220-1V Voltmeter SE Portable analogue meter for measuring voltage, for student experiments; • Measuring ranges (DC and AC): 100, 300 mV, 1, 3, 10, 30 V • Switch: DC, AC, battery check, Off • Moving coil instrument with mirror scale, arc length: approx. 90 mm • Overload protection with diodes • Accuracy: 2% (DC), 3% (AC) • Internal resistance: 100 kOhm/V • Frequency range at AC: 15 Hz - 20 kHz • Max. input voltage: 30 V eff • Powered by 4 x AA Batteries (reserve energy: approx. 3 years) Dimensions: approx. 200 x 140 x 100 mm Weight: approx. 610 g

P3220-1A Ammeter SE Portable analogue meter for measuring current, for student experiments; • Measuring ranges (DC and AC): 10, 30, 100, 300 mA, 1, 3, 10 A • Switch: DC, AC, battery check, Off • Moving coil instrument with mirror scale, arc length: approx. 90 mm • Overload protection with diodes and LED display • Accuracy: 2% (DC), 3% (AC) • Internal consumption: 100 mW • Frequency range at AC: 15 Hz - 20 kHz • Max. input voltage: 30 V eff • Powered by 4 x AA Batteries (reserve energy: approx. 3 years) Dimensions: approx.. 200 x 140 x 100 mm, Weight: approx. 627 g

P3220-1G Galvanometer Portable analogue meter for measuring (small) direct currents, for student experiments; • Measuring ranges: 10, 30, 100, 300 µA; 1, 3, 10, 30, 100, 300 mA; 1, 3, 10 A • Switch: DC (zero at midpoint), battery check, Off • Moving coil instrument with mirror scale, arc length: approx. 90 mm • Overload protection with diodes and LED display • Accuracy: 2% (DC), 3% (AC) • Internal consumption: 100 mW (+ fuse) • Max. input voltage: 30 V eff • Powered by 4 x AA Batteries (reserve energy: approx. 10 years) Dimensions: approx.. 200 x 140 x 100 mm, Weight: approx. 630 g

20

Combi – Demonstration measuring device

DE702-1M Combi – Demonstration measuring device Consisting of:

P3250-1M Multimeter digital “BT”, True RMS P4970-1C Tablet 10“, E101GC P4974-1A Display holder for P4970-1C Tablet

Bluetooth

A digital multimeter transfers the measuring result via Bluetooth to the tablet.

The measurements can be displayed as a diagram in tabular form (analogue)

21

or digitally (height of digits: 65 mm).

P4970-1C Tablet 10“, E101GC

Operating system: Android 8.1 CPU: Quad core, 1,5 GHz RAM: 2 GB Storage: 16 GB/32 GB HDD Camera: two front cameras (each 2.0 MP)

and one on the back (5.0 MP) Screen: 10,1“ IPS, Resolution: 1280 x 800 WiFi: Module IEEE 802.11b/g/n G-Sensor: 4-axis Applications: MSN, Skype, Gmail Office: MS Word, MS Excel, MS PowerPoint and others Speaker: 1 W, 8 Ohm Bluetooth: Bluetooth 4.0 GPS: Yes 3G: 3G, GSM 850/900/1800/1900 MHz,

WCDMA 2100M/850 MHz

Battery: Operating time: Video: Audio: Image: Ports:

3,7 V/6000 mAh 5 – 7 hours AVI, MPEG, MPG, and others MP3, WMA, and others JPG, JPEG, GIF, BMP, PNG 1 x Micro-USB, 1 x TF card, 2 x SIM card, 1 x Headphones

Accessory: 1 x Power supply: 5 V, 2 A 1 x USB cable 1 x Technical description in English Dimensions: Weight:

243 x 172 x 11 mm approx. 580 g

P4974-1A Tablet holder

To use a tablet as a remote display (demonstration measuring device) in combination with Multimeter digital “BT”; Robust metal bracket with rubber pads; Angle setting either 40° or 70°; lightweight, portable, easy to handle Dimensions: approx. 165 x 158 x 120 mm

22

P3250-1M Multimeter digital “BT”, True RMS

Professional multimeter (safety category CAT IV) with True RMS measurement; Data transfer via Bluetooth (4.0) enables measurement acquisition on a tablet, mobile phone or PC (with Bluetooth).

The free apps for Android and iOS enable the following ways to display the measurements: - - -

analogue as a diagram listed in a table (CSV document) digital (on a 10” tablet the measured values are displayed in full screen mode with a digit height of up to 65 mm)

Bluetooth

To measure

Measuring range

Voltage DC (V): 60,00 mV … 1000 V Voltage AC (V): 60,00 mV … 750 V Current DC (A): 600,0 μA … 20,00 A Current AC (A): 600,0 μA … 20,00 A Resistance (Ω): 600,0 Ω … 60,00 MΩ Capacity (F): 60,00 nF … 60,00 mF Frequency (Hz): 9,999 Hz … 9,999 MHz Temperature (°C/°F):-50 … +400 °C

-58 … +752 °F Continuity test Diode test Non-contact voltage detection (NCV)

max. Resolution 0,01 mV 0,01 mV 0,1 μA 0,1 μA 0,1 Ω 0,01 nF 0,001 Hz 1 °C 1 °F

Other functions: Automatic range selection, overload protection, “Data hold” function, relative value, LCD back light, integrated flash light, battery display, automatic shutdown Way of measuring: Safety category: Internal resistance: Size of LCD display: Digit height:

Included in the scope of delivery: 2 measurement cables, 2 isolated alligator clips, temperature sensor, holster, screwdriver, technical instructions Power supply: Fuse protection: Dimensions: Weight:

23

True RMS CAT IV (up to 600 V and CAT III (up to 1000 V) >10 MΩ 58.5 x 41 mm 24.5 mm

9V Battery (6F22) 1 A (1000 V) and 15 A (1000 V) 190 x 90 x 56 mm approx. 320 g

P3250-1MH Magnetic holder for Multimeter digital “BT” To attach the multimeter magnetically to metal panels, making it possible to display the measured value „at the right position“ in an experiment; specially shaped, sturdy metal bracket, powder-coated in yellow Dimensions: 154 x 72 x 53 mm

Show the measured value at the correct position!

Experiment: ELI 031 Voltage divider

24

P3245-1M Multimeter digital, True RMS

The new generation for student experiments: • • • • • • • • • • •

Other functions: „Data hold“, Relative value, Integrated flash light, Battery indicator Way of measuring: True RMS Safety category: CAT IV (up to 600 V) and CAT III (up to 1000 V) Internal resistance: ≥ 10 MΩ Size of LCD display: 58.5 x 41 mm Digit height: 24.5 mm

Resilient Big Handy Attractive colour Big LC-display Automatic range selection Overload protection Incl. temperature measurement LCD back light Automatic shutdown Safety case with holder for measurement cables

To measure

Measuring range

max. Resolution

Voltage DC (V): Voltage AC (V): Current DC (A): Current AC (A): Resistance (Ω): Capacity (F): Frequency (Hz): Temperature (°C/°F):

60,00 mV … 1000 V 60,00 mV … 750 V 600,0 μA … 20,00 A 600,0 μA … 20,00 A 600,0 Ω … 60,00 MΩ 60,00 nF … 60,00 mF 9,999 Hz … 9,999 MHz -50 … +400 °C -58 … +752 °F

0,01 mV 0,01 mV 0,1 μA 0,1 μA 0,1 Ω 0,01 nF 0,001 Hz 1 °C 1 °F

Continuity test Diode test Non-contact voltage detection (NCV) Included in the scope of delivery: 2 measurement cables, temperature sensor, screwdriver, technical instructions

Power supply: 9V Battery (6F22): Fuse protection: 1 A (1000 V) and 15 A (1000 V) Dimensions: 190 x 90 x 56 mm Weight: approx. 320 g

DT812-PM Air quality meter „mini“ For measuring particles ≤ 2.5 μm (fine dust) through the principle of laser scattering as well as the ambient temperature.

Measuring range: 0 - 500 µg/m³ (±10 %) Measuring time: ≥10 min Temperature: -10 - +50°C (±1°C)

14 - 140°F (±2°F) Display height (dual): 17 and 7 mm Backlight white/red (>115 µg/m³) Battery status indicator Built-in 3.7V Li-ion battery (rechargeable via USB cable) Supplied with two brackets and USB cable Dimensions: approx. 64 x 60 x 28 mm

25

The new mini-meters are stand-alone measuring instruments, with bluetooth functionality as well as a sensor for Android or iOS devices. The compact, robust design is suitable for both the laboratory and field trials.

DT812-TH

Temperature and Humidity meter “mini”, BT

Humidity: Temperature:

Measuring interval: Display height (dual):

0 - 100% (± 5%) -10 - +60°C (± 1°C) 14 - 140° F (± 2°F) 0.5 s 10 and 7 mm

• • • • • •

MAX / MIN measurement Data hold function Overrange display Backlight Automatic shutdown after 5 minutes Android and iOS connection via Bluetooth • Incl. 3 x 1.5V batteries (AAA) Dimensions: approx. 137 x 54 x 28 mm

DT812-AN

DT812-DB

• • •

with Bluetooth transfer compact, light, ergonomic low-cost

Sound level meter “mini”, BT

Sound level: 30 - 130 dBA (± 1.5 dB) Measurable frequency: 31.5 Hz - 8 kHz Measured value acquisition: fast (125 ms) / slow (1 s) Display height: 17 mm Condenser microphone: D = 12 mm with windscreen • • • • • •

MAX / MIN / AVG measurement Data hold function Overrange or Undercut display Backlight Automatic shutdown after 5 minutes Android and iOS connection via Bluetooth • Incl. 3 x 1.5 V batteries (AAA) Dimensions: approx. 150 x 54 x 28 mm

Anemometer “mini”, BT

Wind speed: 0 - 30 m / s (± 5%) Selectable units: m/s, km/h, ft/min, knots, mph Measuring interval: 0.5 s Wind temperature: -10 - + 50°C (± 2°C)

14 - 122°F (± 4°F) • Beaufort scale with 12-level analogue bars • Measurement of the sensed temperature (Windchill) • Display height (dual): 12 and 7 mm • MAX / AVG measurement • Data hold function • Overrange display • Backlight • Automatic shutdown after 5 minutes • Android and iOS connection via Bluetooth • Incl. 3 x 1.5V batteries (AAA) Dimensions: approx. 160 x 54 x 28 mm

DT812-LX

Light meter “mini”, BT

Measuring range: 0 … 200.000 Lux (4 %)

0 … 19.999 FC (4 %) Measuring interval: 0,5 s Display height: 17 mm • MAX / MIN measurement • Data hold function • Overrange display • Backlight • Automatic shutdown after 5 minutes • Android and iOS connection via Bluetooth • Incl. 3 x 1.5V batteries (AAA) Dimensions: approx. 160 x 54 x 28 mm

Low-cost pointer meter for studying the weather; easy to read with its clear scale, robust plastic housing, D = 82 mm

DT800-2AB Barometer, simple

DT800-2AH Hygrometer, simple

DT800-2AT Thermometer, simple

Air pressure: 980 – 1040 hPa (mbar)

Humidity: 0 – 100%

Temperatur: -16 … +56 °C

26

SEB SEK Power, Work and Efficiency

P9901-4P SEK Power, Work and

Efficiency P9110-6P Experiment manual:

Power, Work and

Efficiency

Experiments: LAW 01 Electrical energy transmission LAW 02 Power consumption of lamps LAW 03 The wattage of lamps LAW 04 The power of an engine LAW 05 The parallel connection of loads LAW 06 Series connection of loads LAW 07 We build a small electric cooker LAW 08 We operate a small cooling plate LAW 09 Heating and cooling via electrical work LAW 10 We know mechanical work only too well LAW 11 We perform mechanical work via electrical power LAW 12 We compare mechanical work with electrical work LAW 13 A very special electric brake

All experiments can be performed within a short time frame

simple- fast - safe

We make complex experiments simple 13 experiments at an attractive price

27

Set consisting of:

Qty.

Item-no.

Description

1 1 1 1 1 2 5 2 3 4 1 1 1 2 1 5 1 1 1

P3820-1S P3823-MS P2701-1E P2725-2T P3710-2DS DE309-3C DE309-3E DE309-3T P3310-2E P3310-2B DG500-4S DG500-4R C6008-1B C6008-1A DG200-3S DM121-5B P1130-1C DG270-1A P3820-1GZ

Hand generator with controller Hand motor with pulley Heating spiral, SE Peltier element with 2 plugs BC Lamp socket E 10, triple Light bulb, 6V/0,1A, E10 Light bulb, 6V/0,3A, E10 Light bulb, 6V/0,5A, E10 Connecting lead, 25 cm, black, SE Connecting lead, 10 cm, black, SE Double socket, insulated, black Double socket, insulated, red Sample box with lid, plastics, 80 ml, 50 x 50 x 40 mm Sample box with lid, plastics, 30 ml, 35 x 35 x 33 mm Cord, 150 cm, with loop Weight on hook 100 g Dynamometer 2 N, transparent Stickers, removable, pack Gear wheel for hand generator (spare)

P7906-6G P7806-1K

Box insert Power and Work and Efficiency Storage box II small, with lid Plan for storage of all components + 2 stickers

Storage: 1 1

Matching hand generator and hand motor with pulley.

Control elements built into the hand generator and hand motor enable accurate reading of the measuring instruments

The 3-gang lamp socket module enables rapid, clear experimenting

By working with electricity we light a match

28

DE470-9A Electricity set „Three-Phase Current“ 02, „inno“

To perform basic experiments on the subject of the „three-phase current“.

Less than 10 V required for operation.

Storage:

Set consisting of:

29

DE470-1G DE470-2A

1 1

DE470-2M

1

DE470-2K

1

DE720-3D DE720-4S DE453-4L DE453-5L DE309-5S

1 1 1 1 1

DE309-6S

1

DE309-1S

1

DS110-43

1

Three-phase current, base plate Three-phase current, metal ring, pivoting Three-phase current, magnetic needle, pivoting Three-phase current, crank with magnet MBI Delta connection MBI Star connection Coil accessory for linear motor Iron rod, segmented, L=810 mm Light bulb 12 V/100 mA, E10, set of 5 Light bulb 24 V/100 mA, E10, set of 5 Light bulb 4 V/40 mA, E 10, set of 5 Magnetic base 43, with tube and pin

DE470-9E

1

P7806-1G

1

Box insert, three-phase current 02, foam Storage box II big, with cover

Plan for storage of all components + 2 stickers

Experiments: DS 01 Generation of a three-phase current three-phase current generator DS 02 Three-phase current – measuring voltage DS 03 Star connection – amperage at the star point DS 04 Delta connection DS 05 Principle of the three-phase synchronous motor DS 06 Three-phase synchronous motor DS 07 Principle of the three-phase asynchronous motor DS 08 Three-phase asynchronous motor DS 09 Linear motor

Electricity set „Three-Phase Current“ 02, „inno“

To perform basic experiments on the subject of the „three-phase current“.

Less than 10 V required for operation.

DE470-1G Three-phase current, base plate For quickly setting up a safe rotating field with three coils positioned opposite each other at an angle of 120 degrees; sturdy metal plate with three pairs of plug pins to mount the coils on the demonstration module with iron core; metal sleeve at centre to hold the apparatus for demonstrating the rotating three-phase field; L-shaped design with plastic feet for table set-up; three rubber-coated magnetic feet for vertical board set-up.

Dimensions: approximately 240 x 86 x 230 mm

DE470-2M Three-phase current, magnetic needle, pivoting To be used as a magnetic rotor in a synchronous motor, in a horizontal or vertical position; ball bearing-mounted magnetic needle, red and green powder-coated; on metal axis with clamp insert; Magnetic needle: L = 60 mm, W = 15 mm

DE470-2A Three-phase current, metal ring, pivoting To be used as a squirrel-cage rotor in an asynchronous motor, in a horizontal or vertical position; frictionless aluminium ring on needle axis; mounted on support (D = 10 mm); D = 60mm

DE470-2K Three-phase current, crank with magnet To demonstrate the principle of a three-phase current generator; strong neodymium magnet, fitted with red and green plastics caps, D = 24 mm, H = 12mm; mounted on a cantilever arm of a metal crank handle; unit mounted on support (D = 10 mm).

Total length: approx. 230 mm

Three-phase synchronous motor generating three-phase current

30

DL401-3A Polarisation filter set, D = 21 cm, polariscope

For the generation of linear polarised light and to demonstrate the distribution of tension during elastic deformation of specimens in polarised light (photoelastic examination); Two polarising filters on an acrylic glass carrier with a widely visible degree scale; Division in 1°, clear marking of the 90° increments; Block of wood with 4 slots for parallel or slightly offset placement of the filters,marking lines for exact angle adjustment and reading; Outside diameter: 21 cm Diameter of the polarising filters: 15 cm

The large polarising filters allow demonstration of polarisation phenomena even from a considerable distance. No further light source is required.

Markings on the base plate can be used to read off the adjusted angles with precision

31

The filters are simply turned by hand.

DL401-3B Polarisation filters – photo elastic bodies, set To demonstrate the tension distribution in elastic deformation in polarised light; Use in combination with the polarisation filter set DL401-3A (polariscope) • Test body „ring”, D = 60 mm, • Test body „H“, Dimensions: 90 x 50 mm, with round and angular cut-out

Stress distribution on edges, curves and on a ring

DL401-3C Polarisation filter, press and bending set To demonstrate the tension distribution in elastic deformation in polarised light; Use in combination with the polarisation filter set DL401-3A (polariscope) • Metal hood with slots for stable holding of the two polarising filters, • Wooden block (9 x 9 x 5 cm) with marking, for supporting the test bodies, • Test body „beam“ (10 x 2.5 cm) with two support angles, push rod with edge, L = 25 cm, • Test body „crane hook“ (L = 10 cm) with screw, - hook with handle for generating tensile or compressive forces

Stress distribution on crane hooks and beams

32

DL408-4A Interferometer NTL 02

Very compact precision device for measuring e.g. wavelengths of light, refractive indexes of glass or gases; Base: stable metal plate, surface mirror with three adjusting screws, surface mirror adjustable by means of a worm gear (1:50 ratio) and micrometer screw (division 1/100 mm), semi-transparent mirror, lens +20 mm in side-sliding holder, lens -30 mm in sideways relocatable holder, adjustment plate for NTL laser, thread and bore for mounting the swivel unit and the vacuum cell, 4 sturdy metal bolts at the corners serve as impact protection.

Dimensions: 28.5 x 17 cm Working area: made of foam for absorbing vibrations or other shocks Dimensions: 36.5 x 26.5 x 2.5 cm Screen, red: Metal bracket with red foil for colourful reproduction of the interference pattern Dimensions: 11 x 8 x 11 cm Box insert for interferometer, device-shaped Storage box II small, 40 x 30 x 12 cm, with lockable lid and recessed grips

33

Set-up and adjustment in a very short time

• Put the work base in position • Place the interferometer on it

• Place the laser on the adjustment plate • Set up the screen • Slide the converging and diverging lens from the optical axis

• Switch on the laser • Adjust the beam

• Slide the converging lens back into the optical axis • A miniature interference pattern is visible

• Slide the diverging lens back into the optical axis • The device is ready for operation

34

DL408-4K Vacuum cell for interferometer 02 For determining the refractive indices of gases; Metal chamber with two precision glass plates, locking screw for attachment to the interferometer base plate, quick-release coupling for connecting the vacuum hose KS 6 mm.

Inner width of the cell: 12 mm Dimensions: 5 x 2.5 x 4 cm

DL408-4V Suction valve with pressure gauge For the extraction of air and the metered reintroduction of gases into the vacuum cell for the interferometer; Security valve in metal housing, Manometer, metered-dose gun, Quick release coupling for connection of vacuum hoses KS 6 mm Valve dimensions: 10 x 2.5 x 2.5 cm Pressure gauge - diameter: 6 cm

The air is sucked out of the cell using the syringe...

and reintroduced in a very metered way using the gun.

Metered introduction of other gases is just as easy to carry out.

35

DL408-4G Pivoting unit with glass plate for interferometer 02 For the determination of refractive index of translucent solids; Metal bracket with locking screw for attachment to the interferometer base plate, distance plate for the micrometer screw, opening for glass plate; Supplied with glass plate 45 x 27 x 4 mm Dimensions: 14.5 x 5 x 5 cm

The swivel unit can be optimally swivelled in 1/100 mm increments using the micrometer screw.

Light source

We recommend using the DL100-3L laser as a light source.

This is not included in the scope of delivery, however there is room for it in the device-shaped storage space.

36

DL215-1A Additive mixture of colour, compact unit For simple and fast demonstration of additive colour mixing; three super-bright diodes with condenser lens as well as movable lens tube with an integrated projection lens ensure the correct settings for a sharp image at a distance of 15 to 90 cm; diodes in compact mounting movable in any direction via to ball joints; each diode can be turned on/off and is dimmable; white screen and power supply included; free projection area (screen): 16 x 10.5 cm; dimensions: 17 x 15 x 22 cm

DL215-2S Screen large, translucent For large-scale, translucent reproduction of optical images; mounted on 2 x DS140-2R slider stands, horizontal; material: special plastic, white; dimensions: 49 x 49 cm

DL202-1A Subtractive mixture of colour, filter set For a quick and simple demonstration of subtractive colour mixing â&#x20AC;&#x17E;at the windowâ&#x20AC;&#x153;; high-quality colour filters in cyan, magenta and yellow; can be freely arranged in an extra-thick clear film; dimensions of the filters: each 20 x 17 cm

37

DL560-1G Precision Spectro and Goniometer For observing and measuring spectra, for measuring the deflection angle of prisms and grids as well as for the determination of visible dispersion and refractive index; Fixed collimator tube with rotating and adjustable precision gap and fine drive for setting the focal length.

Observation telescope that swivels around the table, with fine drive for setting the focal length.

Locking screw of the swivel arm with additional fine drive which allows minimal and stable settings of the degrees.Rotatable table for prisms and grids, D = 8.5 cm, height adjustable and levelable,with locking screw; one prism and one grid holder can be screwd onto the table.Angle reading in two windows, accurate to 1 minute of arc.(Main scale has a scaling throughout in ½ degree, and 30-part vernier scale).

Dimensions: height: 20.5 cm, length: 54 cm; Mass: 5.4 kg Additionally required: Prism Gratings

Rotatable table for prisms and grids

Angle reading in two windows, accurate to 1 minute of arc.

38

P9901-PK Planck‘s Constant, set, „PIB“

Technical Data: - 6 plug-in blocks (PIB) with diodes of different wavelengths: - 405 nm (light blue) - 465 nm (azure) - 565 nm (green) - 585 nm (yellow) - 660 nm (signal red) - 870 nm (IR) - 1 plug-in block (PIB) current limiter 10µA Can be used on P3910-1A plug-in panel or as an addition to the P9901-4D SEK Electricity 1

P3112-1B Battery supply, 0 - 9 V For experiments in the fields of electricity and electronics, especially desigend for experiments where fine tuning is required; battery supply 0 – 9 V DC, continuously adjustable, with rough and fine tuning; • • • • • •

LED indicators for „Power On“ and „Batt low“ On/Off switch; Case for battery on the outside; Rough tuning: 0 – 8 volts Fine tuning: 0 – approx. 1.0 volt 6 x AA batteries are included with delivery

Dimensions: 160 x 120 x 45 mm Weight: approx. 367 g

Reverse side

39

Delivered in storage box

To determine the Planck constant „h“ with LEDs (inner photoelectric effect). If voltage is applied on an LED, the breakdown voltage can be ascertained through the flash (or with an mA meter).This is characteristic but differs because of the wavelength (colour) of the diode. The Planck constant „h“ can be determined by means of the wavelength of the diode and the breakdown voltage.

MYOD

make your own device

Upper housing part for components in the “Compact” system; extremely robust ABS housing, yellow, surface for marking the circuit symbol or other labels using an appropriate pen, injected 4 mm sockets for laboratory or safety plugs, notches inside for snapping in the base plate Dimensions: 84 x 84 x 26 mm DE620-1A

Block CS - top, without sockets

STN4-ROT

Lamellar plug for cables, 4 mm, red

DE620-2A

Block CS - top, 2 sockets centred

STN4-SCH

Lamellar plug for cables, 4 mm, black

DE620-3A

Block CS - top, 3 sockets

STN4-BLA

Lamellar plug for cables, 4 mm, blue

DE620-4A

Block CS - top, 3 sockets

STN4-GEL

Lamellar plug for cables, 4 mm, yellow

STSI-GEL

Safety plug, 4 mm, yellow

STSI-ROT

Safety plug, 4 mm, red

STSI-SCH

Safety plug, 4 mm, black

KASIL-SWA

Cable silicone, 2.5 mm², black, metre

Block CS - bottom

KASIL-ROT

Cable silicone, 2.5 mm², red, metre

Housing base plate for CS components; Transparent plastic shell with 4 small raised feet and 4 grippers for locking into the upper section (no screws needed) Dimensions: 84 x 84 x 14 mm

KASIL-GEL

Cable silicone, 2.5 mm², yellow, metre

DE620-2AW Block CS - top, 2 sockets laterally, wide DE620-2AE Block CS - top, 2 sockets laterally, narrow

DE630-1B

P6300-1RB Coil bobbin, blue P6300-1RG Coil bobbin, green P6300-1RR Coil bobbin, red P6300-1RS Coil bobbin, black

40

From now on you can also assemble the NTL SE plug-in system yourself.

Encourage cognition by letting the students create their “own” set of equipment,or you can leave self-made parts in the school and continue to use them for many years. Of course you can also use them in this way to enhance existing sets.

Upper housing parts for SE plug-in components; extremely robust ABS housing, yellow, very smooth Surface for marking the switching symbol or other inscriptions using an appropriate pen Dimensions: 40 x 40 x 27 mm

The NTL SE plug-in system would also be a good idea for practical work in technology teaching, wouldn’t it?

P6300-1A PIB - top P6300-1B PIB - top with socket To accommodate cables or similar components with 4 mm laminated plug

P6301-1L Soldering gauge for PIBs For easy and safe soldering of wires or electronic components in NTL PICs; Hardwood board with 4 holes for inserting a PIC base plate, two recesses for easy removal of the base plate Dimensions: approx. 100 x 100 x 20 mm

Housing base plates for SE plug-in components; transparent plastic sheet, embedded nickel-plated 4 mm brass pin with solder cup Dimensions: 36 x 36 mm P6300-1D PIB - bottom with 2 pins straight P6300-2D PIB - bottom with 2 pins angled P6300-3D PIB - bottom with 3 pins P6300-4D PIB - bottom with 4 pins

DE929-3T Phillips screws, set of 40

41

P3910-1A Plug-in panel, small Assembly panel, plastic, for mounting and electrical connection of plug-in blocks P3910ff.

35 socket clusters each with four 4 mm sockets arranged 19 mm apart, which are not connected to each other, while adjacent socket clusters are connected electrically in every direction Rear side of the plug-in panel enclosed with plastic plate, 4 rubber feet for non-slip positioning on the experimental table.

Dimensions: approx. 300 x 220 mm

P6300-1A PIB - top

DE650-2K

P6300-1B PIB - top with socket

Housing upper part for DPIC (Demo Plug-In System) components; robust ABS housing yellow, very smooth surface for marking the switching symbol or other inscriptions using an appropriate pen with 4 screws for attaching a base plate Dimensions: 81 x 81 x 36 mm

To accommodate cables or similar components with 4Â mm laminated plug

P6400-1A

PIBD - top

PIB - bottom for lamellar plugs

DE650-2L STM4-008 Lamellar plug 4 mm, M4x8 mm

For attaching to PIC or DPIC system base plates; brass laminated plug nickel-plated, thread M4 x 8 mm with nut

PIBD - bottom

Housing base plates for demo plug-in components (DPICs); transparent plastic sheet with 12 recesses for 4 mm laminated plugs Dimensions: 77 x 77 mm

DE929-3T Phillips screws, set of 40

The DPIC can also be attached to the small plug-in panel; components with up to 8 connectors can be installed

42

SENSORS

one for all, all for one....

Our extensive new range of sensors enables the following transmission options:

1. Simply display the value using the plug-in display module: take measurements very quickly and easily (comparable to a digital measuring device)

2. With a plug-in BT module via Bluetooth on Android or iOS devices: wireless, flexible use with a tablet or mobile phone

3. via cable to an interface (the conventional variant): fast, reliable, ideal for combining up to 4 sensors at once

If a new type of wireless connection is launched on the market in the next few years, a new module will be added to the sensor. Since no BT module is installed in the sensor itself, the sensor can be used for many years. sensor. Since no BT module is installed in the sensor itself, the sensor can be used for many years.

43

...and for many years to come!

P4930-2B

Display module, NLW

1. Plug the display module into the sensor 2. Switch on 3. Take measurements

P4930-2A

Bluetooth V4.0 data transmitter for sensors, NLW

1. Switch on tablet 4. Switch on transmission module 2. Launch software 5. Scan QR code 3. Attach transmission module to sensor 6. Measure

P4930-1B

Interface (wired), NLW

P4930-1A

Data logger (4-channel), NLW

1.

2.

3.

4.

5.

Switch on computer Connect interface/logger to PC Connect sensor to interface/logger Launch software Take measurements

P4930-1C

Interface (Bluetooth), NLW

P4930-2C

Bluetooth V4.0 data transmitter and display module, NLW

44

P4310-1A P4310-8J P4320-1A P4320-2A P4320-2B P4330-1A P4310-3A P4310-3B P4310-1B P4320-2C P4320-2D P4310-1C P4310-4A P4310-4B P4330-1B P4310-5A P4310-8S P4310-1E P4310-1D P4320-3A P4340-2A P4340-3A P4330-1C P4320-2E P4330-2A P4330-2B P4330-2C P4330-2D P4320-2F P4310-7B P4310-7C P4310-7A P4320-5D P4310-1F P4340-1A P4340-1B P4310-5C P4310-5B P4320-2G P4320-2H

45

2-D motion system, 2-part (emitter+receiver), 10 - 120/0.1 cm, NLW Sensor AC - frequency, 1 Hz - 1 MHz, NLW Sensor alcohol (gaseous), 0 - 2 mg/L, NLW Sensor Ammoniak (NH3), 0 … 100 ppm, NLW Sensor ammonium ions (NH4+), 0 - 1 mol/L, NLW Sensor respiration, 0 - 200 bpm, NLW Sensor illumination, 0 - 5,000/50,000 Lux, NLW Sensor illumination - distribution, 60 mm, NLW Sensor acceleration, +/- 50 m/s², NLW Sensor chlorine CL2, 0 - 20 ppm, NLW Sensor chloride ions (Cl-), 0 - 1 mol/L, NLW Sensor rotary motion, 30 r/s, NLW Sensor pressure (absolute), 0 - 700/0.1 kPa, NLW Sensor pressure (relative), +/- 20/0.01 kPa, NLW Sensor ECG, +/- 5 mV, NLW Sensor electronic compass, 0 - 359°, NLW Sensor electrostatic charge, +/- 100 nC, NLW Sensor distance (small range), 0 - 50/0.1 mm, NLW Sensor distance (large range), 15 - 600/0.1 cm, NLW Sensor Chroma, 0 - 100/0.1%, NLW Sensor moisture (soil), 0 - 100/0.1%, NLW Sensor GPS, NLW Sensor heart rate, 0 - 200 bpm, NLW Sensor potassium ions (K+), 0 - 1 mol/L, NLW Sensor carbon dioxide (dyn), 0 - 5,000 ppm, NLW Sensor carbon dioxide (dissolved), 4.4 - 1,800/0.1 ppm, NLW Sensor carbon dioxide, 0 - 5,000 ppm, NLW Sensor carbon dioxide, 0 - 50,000 ppm, NLW Sensor carbon monoxide (CO), 0 - 1,000 ppm, NLW Sensor force (micro) +/- 2/0.001 N, NLW Sensor force and angle, +/- 20 N, -/+ 180°, NLW Sensor force, +/- 50 N, NLW Sensor conductivity, 0 - 20/0.001 mS/cm, NLW Sensor light gate, NLW Sensor air pressure, 550 - 1,060/0.1 hPa, NLW Sensor humidity (relative), 0 - 100/0.1%, NLW Sensor magnetic induction (3dim.), +/- 50 mT, NLW Sensor magnetic induction, +/- 100 mT, NLW Sensor methane (CH4), 0 - 5 %, NLW Sensor nitrate ions (NO3-), 0 - 1 mol/L, NLW

P4320-5A P4320-5B P4310-9A P4320-5C P4320-2K P4330-3A P4330-3B P4330-3C P4310-6E P4320-2L P4310-8A P4310-8D P4310-8E P4320-2M P4310-8M P4310-8L P4310-8K P4310-8F P4340-4A P4340-2C P4310-6D P4340-2B P4310-6B P4310-6C P4310-6A P4320-6A P4320-2P P4310-1W P4340-1C

Sensor pH meter (fast), 0 - 14/0.01 pH, NLW Sensor pH meter, 0 - 14 pH, NLW Sensor radioactivity, 0 - 40,000 imp./min, NLW Sensor Redox, -500 - +1,200/1 mV, NLW Sensor salinity, 0 - 50/0.001 ppt, NLW Sensor oxygen (dissolved), 0 - 20/0.01 mg/L, NLW Sensor oxygen (O2) B, 1 - 25/0.01%, NLW Sensor oxygen (O2), 0 - 100/0.1%, NLW Sensor sound 20 Hz - 20 kHz, sound level 20 - 120 dB, NLW Sensor sulphur dioxid (SO2), 0 - 20/0.01 ppm, NLW Sensor voltage, +/- 20 V, NLW Sensor voltage, 0 - 0.2/2/20 V, NLW Sensor voltage, 0 - 36 V, AC, NLW Sensor nitrogen dioxide (NO2), 0 - 200 ppm, NLW Sensor current (multi-range), 0 - 0.02/0.2/2 A, NLW Sensor current (micro) +/- 5 µA, NLW Sensor current +/- 2 A, NLW Sensor current, 0 - 2 A, AC, NLW Sensor flow rate, 0 - 4/0.01 m/s, NLW Sensor temperature (soil), -40 - + 60/0.1°C, NLW Sensor temperature (IR), -20 - +200/0.1°C, NLW Sensor temperature (surfaces), -50 - +130/0.1°C, NLW Sensor temperature (fast response), -20 - +130/0.1°C, NLW Sensor temperature (high), 0 - 1200/1°C, NLW Sensor temperature, -50 - +200/0.1°C, NLW Sensor turbidity, 0 - 400/0.1 NTU, NLW Sensor hydrogen (H2), 0 - 100%, NLW Sensor distance (2-part), 0 - 2000/1 mm, NLW Sensor wind speed, 0.3 - 45/0.1 m/s, NLW

Accessories: P4930-2S P4370-1A P4370-1B P4370-2A P4370-2L

BT adapter for flat sensors, NLW Cables for sensors, 4 pc. set, NLW USB cable for data logger, NLW Component holder, 2 pc. set, NLW Charger for remote sensors

46

Editing, photography and layout: Fruhmann GmbH NTL Manufacturer & Wholesaler A-7372 Karl Subjects to error and alterations.

All rights to duplicate or translation reserved.

People who experiment buy NTL

www.ntl.at