Omf810003 gsm power control issue2 01

GS M P owe r Control

www.huawei.com

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Conte nts 1.

Power Control Overview

2.

HWⅡPower Control

3.

HWⅢPower Control

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page3

P owe r Control Ove rvie w 



Power control 

Adjust the transmitting power of BTS and MS when needed.



Based on measurement reports of BTS and MS

Purpose 

Save the power of BTS and MS



Reduce the interference of the network



Increase the quality of the network

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page4

P owe r Control Ove rvie w 

Power control includes uplink power control and downlink power control, Which are performed independently 

Uplink power control: Adjust TX power of MS to let BTS receive stable signal, reduce the uplink co-channel and adjacent channel interference, reduce power consumption of MS



Downlink power control: Adjust BTS TX power to let MS receive stable signal, reduce the downlink co-channel and adjacent channel interference, reduce power consumption of BTS

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page5

P owe r Control Ove rvie w ď Ź

Up link and Down link power control can be enabled independently

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page6

P owe r Control Ove rvie w 

Process of power control commands 

It takes 3 measurement report periods(480ms/period) from command sending to getting the feedback.

BTS sends the command for power control and TA in SACCH header.

SACCCH report period: 26X4=104 frames (480ms)

BTS receives the measurement report

SA0 SA1SA2 SA3 SA0 SA1 SA2SA3 SA0 SA1SA2 SA3 MS adopts the new power level and TA

In the 26 multi-frames, frame 12 sends SACCH. MS obtains SACCH block

MS begins to send the measurement report of the last multi-frame.

MS begins to set up a new SACCH header to report the new TA and power control message.

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page7

Da ta Configura tion of P owe r Control P e riod

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page8

P owe r Control Ove rvie w 

Power control judgment 

Power control judgment is controlled by BTS measurement report pre-processing item which can be selected in handover control data table



MR. Pre-process (measurement report pre-processing): This switch decide where power control be processed. If measurement report pre-processing is “yes”, power control is processed in BTS, and when setting it “no”, power control is processed in BSC

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page9

Da ta Configura tion of MR P re proce s s ing(1)

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page10

Da ta Configura tion of MR P re proce s s ing(1)

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page11

Conte nts 1.

Power Control Overview

2.

HWⅡ Power Control

3.

HWⅢPower Control

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page12

HW II P owe r Control ď Ź

Power control judgment process MR. preprocessing

The power control demand according to receiving level

The power control demand according to receiving quality

General power control judgment Send the power control command

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page13

HW II P owe r Control 

Original data of power control -- Measurement Report(MR)

Uplink MR

BTS

Network

Downlink MR

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page14

HW II P owe r Control ď Ź

Measurement report

Uplink measurement report

Downlink measurement report

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page15

HW II P owe r Control 

MR. preprocessing in HW II PC algorithm consists of four steps 

Interpolation



Compensation (optional)



Prediction (optional)



Filter

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page16

HW II P owe r Control 

MR Interpolation – recover the lost measurement report 

BTS may fail to receive the MR from MS, and it needs to recover the lost measurement reports. If the lost MR amount is within the allowed range (Allo w e d MR Num b e r Lo s t), then recovers the lost MR according to the specific algorithm. 

S e r v ic e c e ll: lin e a r a lg o rit h m



Ne ig h b o rin g c e ll: t h e lo w e s t v a lu e d e fin e d in GS M s p e c ific a t io n (-1 1 0 d Bm )

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page17

HW II P owe r Control 

MR Interpolation – recover the lost measurement report Flow R us M o u tin Con

MR

MR

…

MR

No. n+4

MR

…

MR

No. n

Missing by some reasons

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page18

Da ta Configura tion of MR P re proce s s ing

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page19

HW II P owe r Control 

MR. compensation 



Purpose: Ensure the accuracy of selection of the history measurement report before filter.

Implementation steps: 

1 . Pu t t h e c u rre n t re c e iv in g m e a s u re m e n t re p o rt in t o t h e m e a s u re m e n t re p o rt c o m p e n s a t io n q u e u e .



2 . Re c o rd t h e c h a n g e d in fo rm a t io n o f t h e t ra n s m it t in g p o w e r a c c o r d in g t o t h e MS a n d BTS p o w e r le v e ls in t h e m e a s u re m e n t re p o rt .



3 . Aft e r fin is h t h e m e a s u re m e n t re p o rt in t e rp o la t io n , s y s t e m w ill c o m p e n s a t e t h e re c e iv in g le v e l o f t h e h is t o ry m e a s u re m e n t re p o rt a c c o r d in g t o t h e p o w e r c h a n g e in fo rm a t io n . Th e c o m p e n s a t e d m e a s u re m e n t re p o rt s w ill b e t h e o rig in a l d a t a in t h e filt e r p ro c e s s .



4 . Filt e r t h e c o m p e n s a t e d m e a s u re m e n t re p o rt s .

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page20

HW II P owe r Control MR. compensation Power control effect diagram of measurement report compensation 70

Y axis

60

Diagram when there is no power control

50

Power control diagram when there is measurement report compensation

40

Power control diagram when there is no measurement report compensation

30 20 10 0

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

ď Ź

X axis

The Theexpected expectedreceiving receivingsignal signallevel: level:30 30 The Thepower powercontrol controlwill willbe bemore moreeffective effectivewith withmeasurement measurementreport reportcompensation. compensation.

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page21

Da ta Configura tion of MR. Compe ns a tion

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page22

HW II P owe r Control 

MR. prediction 

Purpose: Avoid power control later than needed, the delay is dangerous in case of poor level or bad quality



Implementation procedure 1.

An a ly ze t h e t e n d e n c y o f MR b y t h e h is t o ric a l m e a s u r e m e n t re p o r t s a ft e r in t e rp o la t io n .

2.

Gu id e b y t h e t e n d e n c y , t o p r e d ic t t h e v a lu e s o f m e a s u r e m e n t re p o r t t o b e r e c e iv e d . Th e r e a re 0 ~ 3 m e a s u r e m e n t re p o r t s p r e d ic t io n , w h ic h a re c o n fig u re d o n LMT.

3.

Filt e r t h e in t e rp o la t e d , c o m p e n s a t e d a n d p r e d ic t e d m e a s u r e m e n t re p o r t s , a n d im p le m e n t p o w e r c o n t ro l

Copyright © 2009 s Co., Ltd. All rights reserved. ju dHuaw g meieTenchnologie t.

Page23

HW II P owe r Control MR. prediction Diagram of power control effect comparison between prediction filter and mean filter

50 45 Y axis

40

No power control

35

Mean filter power control

30

Prediction filter power control

25 20 15

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

ď Ź

X axis

The Theexpected expectedreceiving receivingsignal signallevel: level:30 30 The Thepower powercontrol controlwith withprediction predictionfilter filterwill willbe bemore moreeffective effective than thanthat thatwith with mean meanfilter filter Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page24

Da ta Configura tion of MR. P re diction

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page25

HW II P owe r Control 

MR. filter – Smooth the instantaneous fading point 

Calculate the average value within the filter window

us M o u n ti Con

ow R Fl MR

MR

MR

…

MR

MR

…

MR

Filter----Average several consecutive MRs

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page26

Da ta Configura tion of MR. filte r

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page27

HW II P owe r Control J udgme nt 

Power control demand based on receiving level. 

After measurement report pre-processing, the power control module makes a comparison between the expected signal level and the current receiving signal level.



Calculate the transmitting power level step size to be adjusted, making the receiving level value closer to the expected value.



Adopt variable step size when decreasing the transmitting power according to the receiving level, so as to achieve the expected level as soon as possible.

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page28

HW II P owe r Control J udgme nt 

Power control demand based on receiving quality 





After measurement report pre-processing, the power control module makes comparison between the expected quality level and the current receiving quality level.

Calculate the step size of the transmitting power level to be adjusted: increase the transmitting power in case of poor receiving quality, and decrease the transmitting power in case of good receiving quality.

Adopt fixed step size when adjust the transmitting power according to the receiving quality.

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page29

HW II P owe r Control J udgme nt 

General power control judgment Power control by receiving level

Power control by receiving quality

Power control by signal level and quality

↓ AdjStep_Lev

↓ AdjStep_Qul

↓ max(AdjStep_Lev,AdjStep_Qul)

↓ AdjStep_Lev

↑ AdjStep_Qul

No action

↓ AdjStep_Lev

No action

↓ AdjStep_Lev

↑AdjStep_Lev

↓ AdjStep_Qul

↑AdjStep_Lev

↑AdjStep_Lev

↑ AdjStep_Qul

↑AdjStep_Lev

No action

↑AdjStep_Lev

No action

↓ AdjStep_Qul

↓ AdjStep_A

No action

↑ AdjStep_Qul

↑ AdjStep_B

No action

No action

No action

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

↑ max(AdjStep_Lev,AdjStep_Qul)

Page30

HW II P owe r Control Fe a ture 

Adaptive power control: 

Adaptive power control refers to changeable power control strategy according to the communication environment, it makes power control more effective and stable. 

Au t o m a t ic a lly c h a n g e t h e a d ju s t a b le m a x im u m s t e p s ize o f p o w e r c o n t ro l a c c o rd in g t o d iffe r e n t c o m m u n ic a t io n e n v iro n m e n t (d iffe r e n t r e c e iv in g q u a lit y ).



Ad o p t d iffe re n t p o w e r c o n t r o l s t r a t e g ie s a c c o rd in g t o d iffe r e n t c o m m u n ic a t io n e n v ir o n m e n t s (d iffe r e n t r e c e iv in g q u a lit y a n d le v e l).



Ma x . s t e p is d iffe r e n t b e t w e e n in c re a s e a n d d e c re a s e .

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page31

HW II P owe r Control Fe a ture 

Power control within the upper/lower thresholds 

Power control will not execute if the signal level and quality is within the threshold bands.



Avoid the signal level fluctuation caused by power control.



The upper threshold can be increased dynamically in case of bad quality.

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page32

Da ta Configura tion for UL Rx_Le v Uppe r/Lowe r Thre s hold

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page33

Da ta Configura tion for UL Uppe r/Lowe r Qua lity Thre s hold

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page34

Da ta Configura tion for DL Rx_Le v Uppe r/Lowe r Thre s hold

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page35

Da ta Configura tion for DL Uppe r/Lowe r Qua lity Thre s hold

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page36

Da ta Configura tion of P owe r Control (Rx_Le v)

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page37

Da ta Configura tion of P owe r Control (Rx_Le v)

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page38

Da ta Configura tion of P owe r Control (Rx_Le v)

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page39

Da ta Configura tion for UL/DL Ba d Qua lity

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page40

HW II P owe r Control Adva nta ge s 

Measurement report compensation – to makes power control judgment more accurate



Measurement report prediction --to avoid power control later than needed, the delay is dangerous in case of poor level or bad quality



Power control expected signal level and quality threshold falls within a band, this avoids receiving signal level fluctuate up and down frequently

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page41

Exe rcis e 

Exercises for HW II power control 

Given conditions: 

Th e u p lin k re c e iv in g le v e l is -5 5 d Bm , t h e q u a lit y is le v e l 0 . Po w e r c o n t ro l a lg o r it h m is HW II.



Da t a c o n fig u ra t io n is a s fo llo w s : Up lin k s ig n a l le v e l u p p e r t h re s h o ld : -6 0 d Bm , u p lin k s ig n a l le v e l lo w e r t h re s h o ld : - 8 0 d Bm . Up lin k s ig n a l u p p e r q u a lit y t h re s h o ld : le v e l 1 . Up lin k s ig n a l lo w e r q u a lit y t h re s h o ld : le v e l 2 . Th e d o w n w a r d a d ju s t a b le s t e p s iz e o f q u a lit y b a n d 0 is 1 6 d B, o f q u a lit y b a n d 1 is 8 d B, a n d o f q u a lit y 2 is 4 d B. Th e u p w a rd a d ju s t a b le s t e p s iz e o f r e c e iv in g le v e l is 1 6 d B. Th e u p w a rd o r d o w n w a rd a d ju s t a b le s t e p s iz e fo r p o w e r c o n t r o l b y q u a lit y a re b o t h 4 d B.



Question: What will be the uplink stable receiving level after power control?

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page42

Exe rcis e 

Exercises for HW II power control 

Answer. 

Firs t , t ra n s m it t in g p o w e r t o b e re d u c e d a c c o rd in g t o re c e iv in g le v e l = a c t u a l re c e iv in g le v e l -(u p lin k s ig n a l le v e l u p p e r t h re s h o ld + u p lin k s ig n a l le v e l lo w e r t h re s h o ld )/2 ＝ -5 5 - (-6 0 + (-8 0 ))/2 ＝ (5 5 )-(-7 0 ) ＝ 1 5 d B. As t h e re c e iv in g q u a lit y is le v e l 0 , d o w n w a rd a d ju s t a b le s t e p s iz e o f q u a lit y b a n d 0 c a n b e u s e d -- d e c re a s e 1 6 d B.



S e c o n d , t h e t ra n s m it t in g p o w e r t o b e d e c re a s e d a c c o rd in g t o re c e iv in g q u a lit y = a s “p o w e r c o n t ro l a d ju s t m e n t s t e p s iz e b y q u a lit y ”is 4 d B, t h u s d e c re a s e 4 d B.



Th e re fo re , a c c o rd in g t o t h e g e n e ra l ju d g e m e n t o n p o w e r c o n t ro l, 1 5 d B s h o u ld b e d e c re a s e d .

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page43

Exe rcis e 

Exercises for HW II power control 

Answer . 

Aft e r t h e im p le m e n t a t io n o f s t e p 1 p o w e r c o n t r o l, t h e r e c e iv in g le v e l b e c o m e s : -5 5 d Bm -1 5 d B= -7 0 d Bm , S u p p o s e t h e q u a lit y r e a c h a lr e a d y in le v e l 1 h e re .



Firs t : t h e re c e iv in g le v e l v a lu e is b e t w e e n -8 0 d Bm ~ 6 0 d Bm , n e e d n ’ t a d ju s t .



S e c o n d : t h e re c e iv in g q u a lit y v a lu e is b e t w e e n 0 a n d 2 , needn’ t a d ju s t .



Th e re fo re , t h e u p lin k s t a b le re c e iv in g le v e l = -7 0 d Bm .

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page44

Conte nt 1.

Power Control Overview

2.

HWⅡPower Control

3.

HWⅢ Power Control

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page45

HW III P owe r Control Flow MR. Preprocessing

Stop PC, waiting the next MR.

Initial MR. process

Yes

Number of lost MR. > N? No MR. Interpolation

No Power Control

Exponent Filter Slide Window Filter Calculate the power control step for BTS and MS

Yes

Rx_lev&(Qual.+FH gain) are within expected window?

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

No Power control implement

Page46

Me a s ure me nt Re port P re proce s s ing 

For the measurement report preprocessing, there are three differences between HW II and HW III power control ： 

Initial discarded MR. number



Interpolation method



Filter calculation

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page47

Me a s ure me nt Re port P re proce s s ing 

Initial discarded MR. number 

Avoiding the access period measurement report influence power control accuracy, system discards some initial measurement report.





HW II: d is c a rd 4 in it ia l MR. fix e d ly .



HW III: s e t it v ia Sig n a l/Tra ffic C h a n n e l Disc a rd MR. Nu m b e r.

MR. interpolation method 

Rx_lev: If Rx_lev(k) is lost, recover it as Rx_lev(k-1).



Rx_qual: If Rx_qual is lost, recover it as quality lever 7.

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page48

Da ta Configura tion of Initia l Dis ca rde d MR. Numbe r

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page49

Me a s ure me nt Re port P re proce s s ing 

MR. filter calculation 

Quality filter 

Quality class value will be converted to BER and set up the correspondence relationship with CIR as below table.



Ca lc u la t e t h e a v e ra g e CIR a c c o r d in g t o t h e s e le c t e d filt e r m e th od .

Quality Class CIR (dB)

0

1

2

3

4

5

6

7

22

18

16

14

12

9

6

4

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page50

Me a s ure me nt Re port P re proce s s ing 

MR. filter calculation 

filter algorithm: exponent filter and slide window filter 

Ex p o n e n t filt e r – ca _filte re d1 (1)=ca (1)

k=1

– ca _filte re d1 (k)=a *ca (k)+(1-a )*ca _filte re d1 (k-1)

k>1

~ ca : origina l re ce iving le ve l or qua lity ~ ca _filte re d1: re ce iving le ve l or qua lity a fte r e xpone nt filte r ca lcula tion ~ k: s e ria l numbe r of me a s ure me nt re port ~ a : e xpone nt filte r coe fficie nt, a =1 / (2^(w/2)), a nd w is e xpone nt filte r le ngth

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page51

Me a s ure me nt Re port P re proce s s ing 

Filter algorithm 

Slide window filter 

c a _filt e re d (1 ) = c a _filt e re d 1 (1 ) k= 1



c a _filt e re d (k ) = [c a _filt e r e d 1 (1 )+ …+ c a _filt e re d 1 (k )] / k 1 < k< w



c a _filt e re d (k ) = [ c a _filt e re d 1 (k -w + 1 )+ ...+ c a _filt e re d 1 (k )] / w k> = w – ca _filte re d1: re ce iving le ve l or qua lity a fte r e xpone nt filte r – ca _filte re d: re ce iving le ve l or qua lity a fte r window filte r – k: s e ria l numbe r of me a s ure me nt re port – w: s lide filte r window

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page52

Da ta Configura tion of Filte r(DL)

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page53

Da ta Configura tion of Filte r(UL)

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page54

P owe r Control J udgme nt 

During HW III power control judgment, system will calculate radio channel gain. 

Suppose: In SACCH period k, useful signal is c(k), interference is I(k), radio channel gain is g(k) and transmit power for BTS or MS is p(k). The below formulas are calculated by logarithm:

10

ca _ filtered ( k ) 10

Rx_lev

= 10

c(k ) 10

+ 10

Useful signel

I (k ) 10

(1)

Interference

C/I qa_filtered(k) = c(k) – I(k)

(2)

c(k) = p(k) – g(k)

(3)

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page55

P owe r Control J udgme nt 

Radio channel gain calculation: 

According to (1) and (2), we can get c(k)

c(k ) = ca _ filter (k ) + qa _ filter (k ) − 10 × lg(1 + 10 

qa _ filtered ( k ) 10

)

Input c(k) to (3), get g(k) = p (k) – c (k). So c alc ulate the g (k)

fo r BTS and MS

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page56

P owe r Control J udgme nt 

BTS power control step calculation: step(k) = - ( sfactor*( BsTxMaxPower - g(k) - SThr) + q fa c t o r*( q a _filt e re d (k ) + Q O ffFh - Q Th r) ); S Th r = (S Th r Up + S Th rDo w n ) / 2 ; Ph y s ic a l m e a n in g is re c e iv e d u s e fu l s ig n a l.

Q Th r = (Q Th rUp + Q Th rDo w n ) / 2 ; Ph y s ic a l m e a n in g is re c e iv e d CIR w it h o u t h o p p in g .

If s t e p (k ) > 0 , s o s t e p (k ) = 0 ; No t e s : s fa c t o r ：【 HW III DL Re x Le v Ad ju s t Fa c t o r 】 q fa c t o r ：【 HW III DL Re x Q u a l. Ad ju s t Fa c t o r 】 Bs Tx Ma x Po w e r ： t h e m a x im u m p o w e r le v e l o f o c c u p ie d c a rrie r S Th r ： t h e m e a n le v e l o f e x p e c t e d re c e iv in g le v e l w in d o w Q Th r ： t h e m e a n le v e l o f e x p e c t e d re c e iv in g q u a lit y w in d o w Q O ffFh ： fre q u e n c y h o p p in g g a in Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page57

P owe r Control J udgme nt 

MS power control step calculation: s t e p (k ) = - ( s fa c t o r*( Ms Tx Ma x Po w e r - g (k ) - S Th r) + q fa c t o r*( q a _filt e r e d (k ) + Q O ffFh - Q Th r ) ); STh r = (S Th rUp + S Th rDo w n ) / 2 ; Q Th r = (Q Th rUp + Q Th r Do w n ) / 2 ; If s t e p (k ) > 0 ， t h e n s t e p (k ) = 0 ;

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page58

Da ta Configura tion of P owe r Control J udgme nt

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page59

Da ta Configura tion of P owe r Control J udgme nt

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page60

Da ta Configura tion of P owe r Control J udgme nt

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page61

Da ta Configura tion of P owe r Control J udgme nt

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page62

Da ta Configura tion of P owe r Control J udgme nt

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page63

Da ta Configura tion of P owe r Control Adjus t Fa ctor

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page64

P owe r Control J udgme nt 

Adjustment protection 

For avoiding too rapid adjustment, parameter [HWIII DL/UL MAX DownStep/UpStep] is used to control the maximum power control step.



If the difference between power control step(k) and previous one step(k-1) is bigger than maximum power control step configured above, just take the maximum power control step as the difference between them, so as to limit the current power control command step(k).

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page65

Da ta Configura tion of P owe r Control S te p

Copyright Š 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page66

P owe r Control J udgme nt 

If Rx _le v up p e r thre s ho ld >= Rx_Lev >= Rx _le v lo w e r thre s ho ld and Rx _q ual up p e r thre s ho ld >= [RxQual + QOffFh] >= Rx_qual lower threshold, step(k)=step(k-1) 

QOffFh is depended on hopping gain table

Number of MA

1

2

3

4

5

6

7

>=8

QOffFh (dB)

0

2

3

4

4.3

4.7

5.0

5.3

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page67

HW III P owe r Control Fe a ture s 

Exponent filter enhance the measurement report process speed.



In HW II PC, receive level and quality be considered independently and then general power control judgment will be done. While in HW III PC, the final result will be got from the general formula.



Difference quality threshold be set for the difference service, such as AMR, FS and HS.



Hopping gain also be considered.

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page68

Que s tion 

Given condition ： 

The current UL_Re_Level: -75dBm ， UL_Re_Quality: 4(qa_filtered (k) =12) ， Radio channel gain(g(k)): 110dB, there are 7 hopping frequency, Max power output of MS is 2W(33dBm)



HWIII is available ， data configuration is as following:



【 [HWIII UL RexLev Upper Threshold] 】： 30



【 HWIII UL RexLev Lower Threshold 】： 20



【 HWIII DL FS Rex Qual. Upper Threshold(dB)] 】： 22



【 HWIII UL FS Rex Qual. Lower Threshold(dB)] 】： 16



【 HWIII UL RexLev Adjust Factor 】： 4 【 HWIII UL Rex Qual.Adjust Factor 】： 6



【 HWIII UL MAX DownStep(dB) 】： 8 【 HWIII UL MAX UpStep(dB) 】： 8

Quality Class CIR (dB)



0

1

2

3

4

5

6

7

Number of MA

1

2

3

4

5

6

7

8

22

18

16

14

12

9

6

4

QOffFh (dB)

0

2

3

4

4.3

4.7

5.0

5.3

Question ： What will be the power output of MS after power control ？ Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page69

Que s tion 

Answer: step(k) = - ( sfactor×( MsTxMaxPower - g(k) - SThr) ＋ q fa c t o r×( q a _filt e re d (k ) + Q O ffFh - Q Th r) ) 30 + 20 22 + 16 = −{{0.4 × [33 − 110 − ( − 110)]} + 0.6 × (12 + 5 − )} 2 2 = −2dB Aft e r p o w e r c o n t ro l ： Po w e r o u t p u t o f MS : 3 3 -2 = 3 1 d Bm S u p p o s e t h e c u rre n t g (k )= 1 1 5 d B, c u rre n t q u a lit y :3 (CIR= 1 4 d B) ， t h e n Fo r le v e l ： -9 0 d Bm < 3 1 -1 1 5 < -8 0 d Bm Fo r q u a lit y ： 1 6 < 1 4 + 5 < 2 2 S o p o w e r c o n t ro l s t o p s ， t h e p o w e r o u t p u t o f MS 3 3 -2 = 3 1 d Bm

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page70

S umma ry 

In this course, we have learned: 

Power control procedure



HW II power control algorithm



HW III power control algorithm



Data Configuration of HWII and HWIII

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

Page71

Thank you www.huawei.com