Skip to main content

Rear Ventilated Facades (ENG)

Page 1

Rear Ventilated Facades Screws, Facade Anchors, Insulation support anchors


Rear ventilated facades

Imprint Publisher: EJOT Baubefestigungen GmbH 57334 Bad Laasphe Layout and realisation: EJOT Baubefestigungen GmbH 57334 Bad Laasphe Legal Notes EJOT products undergo continuous further development. Technical specifications, ranges and prices are subject to changes. For the latest information about our products, please visit our online shop at www.ejot.de/bau During planning and use of our products, please comply with the accepted rules of technology, construction legislation and the relevant safety regulations. The approvals granted by the building authorities for our products can be downloaded from www.ejot.com. General terms and conditions: Our general terms and conditions can also be found at www. ejot.com (footer: Terms & Conditions) ©2019 by EJOT Baubefestigungen GmbH EJOT®, ejotherm®, Delta PT® und PT® are registered trademarks of EJOT GmbH & Co. KG. CRONIMAKS®, Corremaks®, EJOFAST®, Dabo®, ECOmate ® FR-variotool® and Solar Ready® are registered trademarks of EJOT Building Fasteners GmbH. SDS plus® is a registered trademark of Robert Bosch GmbH. DEKTITE® is a registered trademark of Deks Industries Pty. Ltd. TORX® is a registered trademark of Acument Intellectual Properties, LLC.

2


Rear ventilated facades

Screws

Facade anchors and nylon anchors

Insulation support anchors

3


The Fastener.

Horizontal and vertical:

CROSSFIX®

CROSSFIX® Facade system The flexbile substructure system made of A4 stainless steel

CROSSFIX® is the first 100% A4 stainless steel substructure for horizontal and vertical support profiles. Increase your flexibility, facilitate the assembly and save precious time and storage costs. With the CROSSFIX® system, you get everything from one supplier – in proven EJOT quality.

www.ejot.com 4

www.ejot.com


Rear ventilated facades Self-drilling screws

EJOT® self-drilling screw JT4-3H/5-5.5x19 EJOT® self-drilling screw JT9-3H/5-5.5x19 AF8

SCAN TO SHOP

Length [mm]

5 mm P-BWU021980001

Price/100 Order description [EUR]

JT4 made of A2 stainless steel 19 500 19 100 JT9 made of A4 stainless steel 19 500 19 100

Article number

EAN

JT4-3H/5-5.5x19 JT4-3H/5-5.5x19 VE100

7 380 540 300 6 380 540 300

4061245014289 4061245014876

JT9-3H/5-5.5x19 JT9-3H/5-5.5x19 VE100

7 380 540 340 6 380 540 340

4061245014272 4061245014869

Application range ll To form floating and fixed points on substructures of rear-ventilated facades ll Fastening pre-drilled stainless steel or aluminium wall brackets to aluminium support profiles ll For component assemblies from 3.1 – 5.0 mm (component I + component II) Characteristics ll A2 or A4 stainless steel Note Component assemblies checked with Rm (component II) ≥ 190, ≥ 215 and ≥ 245 N/mm2. For bearing values, please refer to the general building authorities test certificate (abP) PBWU02-1980001.

www.ejot.com

Technical specifications Diameter Drilling capacity Drive Flange head Length non-threaded part

5.5 mm 3.0 mm Hexagon A/F8 Ø 13 mm 5.0 mm

Possible component assemblies Component I [mm] 1.5 (stainless steel) 3.0 (aluminium)

Component II [mm]

Rm support profile/ Wall bracket

1.6 2.0 2.4 1.6 2.0

≥ 190 N/mm2

≥ 190 N/mm2

5


Rear ventilated facades Self-drilling screws

EJOT® self-drilling screw JT6-2/5-5.0 VARIO EJOT® self-drilling screw JT9-2/5-5.0 VARIO SCAN TO SHOP

Length [mm]

AF8 P-BWU02178006

Price/100 Order description [EUR]

JT6 made of A4 stainless steel with hardened steel drill point 30 500 JT6-2/5-5.0x30 Vario 30 100 JT6-2/5-5.0x30 Vario VE100 JT9 made of A4 stainless steel 25 500 JT9-2/5-5.0x25 Vario 25 100 JT9-2/5-5.0x25 Vario VE100

Watch the video now: https://youtu.be/pXs-bv1N3dA

Application range ll To form floating and fixed points on substructures of rear-ventilated facades ll Fastening pre-drilled stainless steel or aluminium wall brackets to aluminium support profiles Characteristics ll One screw for all part combinations ll Sliding washer E14, Ø 14 mm ll Buffer zone between the screw head and sliding disk prevents excessive clamp load of the joint. ll Pre-assembled captive sliding washer ll Consistently low contact pressure prevents stick-slip phenomenon ll No stripping / destruction of the thread in component II resulting in high tensile loading capacity ll High tensile and transverse load transmission in component II due to fine pitch thread ll General building authorities test certificate (abP) as proof of usability according to DIN 18516-1 (also available as informal English translation) ll Case hardened drill point of the JT6 version for fastening in steel support profiles (not part of the abP) ll Wall brackets made of stainless steel and aluminium are part of the abP ll Buffer zone serves as visual set control ll Same assembly concept for floating and fixed points

Article number

EAN

3 598 077 991 6 598 077 991

4061245014999 4061245021904

3 500 777 490 6 500 777 490

4061245020686 4061245021508

Technical specifications Diameter Drilling capacity Drive

5.0 mm 3.0 mm Hexagon A/F8

Possible part combinations Component I [mm] 1.5 (stainless steel) 2.0 (stainless steel) 3.0 (stainless steel) 2.0 (aluminium) 3.0 (aluminium) 4.0 (aluminium) 5.0 (aluminium)

Component II [mm]

Rm support profile/ Wall bracket

2.0 2.5 3.0 2.0 2.5 3.0 2.0 2.5 3.0 2.0 2.5 3.0 2.0 2.5 3.0 2.0 2.5 3.0 2.0 2.5 3.0

≥ 190 N/mm2

Note Component assemblies checked with Rm (component II) ≥ 190, ≥ 215 and ≥ 245 N/mm2. For bearing values, please refer to the general building authorities test certificate (abP) PBWU02-178006.

6

www.ejot.com


Rear ventilated facades Self-drilling screws

Drive hexagon A/F 8

isual set control by correct compression of V the buffer zone

Large collar prevents rubbing of thread flanks in the slotted hole of the wall bracket. No stripping or destruction of the thread in component II

Pre-assembled captive sliding washer with buffer zone

Fine pitch thread creates load bearing thread in component II Low pitch allows precise compression of the buffer zone and high self-locking of the screw in component II

Extreme drilling speed even at low axial pressure

Recommended accessories EJOT® A/F8-Vario Tool Article No. 9 152 900 000

www.ejot.com

Cordless metal screwdriver ASCS 6.3 Select Article No. 9 150 200 003

7


Rear ventilated facades Self-drilling screws

The LT system for facades Forcing tension under control: The LT fastening system with plastic sleeves specifically matched to the screws ensures optimum fastening of the cladding panels. The LT screws can be combined with suitable centring bushes - adapted to every application.

Drive Hexalobular TX25 Head diameter 16 mm to cover slotted holes and large pre-drill diameters Very flat screw head for aesthetic facade design XT version with cutting ring: Protective film of the facade panel is cut in and can be removed completely after assembly

Optionally with free spin zone for a defined low clamp load Centring bushes to form fixed points...

and floating points

Processing tip Wobble-free fastening when using the LT/STS Tool

8

www.ejot.com


Rear ventilated facades Self-drilling screws

Product finder LT system JT4-LT3-5.5x25 KD16

JF3-LT2-5.5x30 KD16

JT4-LT-XT3H/4-5.5x19 KD16

JT4-LT-XT3H/6-5.5x25 KD16

JT3-LT3-5.5x30 KD16

JT4-LT2/6-6x50 KD16

A2 stainless steel

A2 stainless steel with hardened steel point1)

A2 stainless steel

A2 stainless steel

A2 stainless steel with hardened steel drill point

A2 stainless steel

all common cladding panels

all common cladding panels

Aluminium panels ≥ 2.0 mm

Aluminium composite panels 4.0 mm

all common cladding panels

all common cladding panels

-

-

4.0 mm

6.0 mm

-

-

For substructures made of

Aluminium

Steel / aluminium

Aluminium

Aluminium

Steel / aluminium

Timber

Drilling capacity (tI pre-drilled) tII

1.5 - 3.0 mm

0.4 - 1.5 mm

1.5 - 3.0 mm

3.0 mm

1.5 - 2.5 mm

1.5 - 2.0 mm

1 - 15 mm

1 - 15 mm

2 - 3 mm

4 - 5 mm

1 - 15 mm

2 - 19 mm

ETA-10/0200

ETA-10/0200

-

P-S 18 0447

ETA-10/0200

ETA-10/0200

Centring bushes Ø 11/4 Ø 11/6 Ø 11/8

Centring bushes Ø 11/4 Ø 11/6 Ø 11/8

Centring bushes Ø 11/2

XT centring bushes Ø11/4

Centring bushes Ø 11/4 Ø 11/6 Ø 11/8

Centring bushes Ø 11/2 Ø 11/4 Ø 11/6 Ø 11/8

Screw type

Material

Application2)

Free spin zone3)

Clamp thickness tfix abP / ETA

Centring bushes / XT centring bushes

JF screw requires more axial pressure than JT screw with classic cutting bit in order to penetrate component II. Without swarf: Contrary to conventional self-drilling screws with classic cutting bit, ribbon swarfs, spiral swarfs or spiral swarf pieces are avoided during assembly. 2) Remark: Please note the respective approval of the facade panel and the assembly instructions of the manufacturer. 3) Free spin zone: Screws without free spin zone must be loosened by 90 degrees after connecting surface in order to ensure reliable sliding. 1)

www.ejot.com

9


Rear ventilated facades Self-drilling screws

EJOT® self-drilling screw JT4-LT-3-5.5x25 16 mm

TX25 SCAN TO SHOP

ETA-10/0200

Length [mm]

max. panel thickness [mm]

25

12

Price/100 Order description [EUR] 500

Application range ll For fixing facade panels to 1.5-3.0 mm aluminium substructures ll Can be combined with LT fixed and floating point sleeves Characteristics ll A2 stainless steel ll Pan head Benefits ll To cover slotted holes and large pre-drill diameters ll Also available in RAL lacquering ll Flat screw head for aesthetic facade design ll Wobble-free fastening by using the LT tool

10

JT4-LT-3-5.5x25 KD16

Article number

EAN

7 384 207 300

4061245014029

Note Please note the respective approval of the facade panel and the assembly instructions of the manufacturer. Processing information for floating points on cladding panels Stop fastening as soon as the screw head connects to the surface and turn the screw back a quarter turn in order to remove the clamp load from the connection.

Technical specifications Diameter Drilling capacity (tI pre-drilled) + tII Drive Head diameter Head height

5.5 mm 1.5-3.0 mm Hexalobular TX25 16 mm 2.0 mm

www.ejot.com


Rear ventilated facades Self-drilling screws

EJOFAST® self-drilling screw JF3-LT-2-5.5 TX25

16 mm

SCAN TO SHOP

ETA-10/0200

Length [mm]

max. panel thickness [mm]

30

10

Price/100 Order description [EUR] 500

Application range ll For fixing facade panels to 1.0-2.0 mm aluminium substructures without swarfs ll Can be combined with LT fixed and floating point sleeves Characteristics ll A2 stainless steel with hardened steel drill point ll Pan head Benefits ll To cover slotted holes and large pre-drill diameters ll Also available in RAL lacquering ll Flat screw head for aesthetic facade design ll Wobble-free fastening by using the LT tool ll Fastening without swarf*

www.ejot.com

JF3-LT-2-5.5x30 KD16

Article number

EAN

7 384 212 301

4061245014005

Note Please note the respective approval of the facade panel and the assembly instructions of the manufacturer. Attention JF screw requires more axial pressure than JT screw with classic cutting bit in order to penetrate component II.

*Without swarf means that - contrary to conventional self-drilling screws with classic cutting bit - ribbon swarfs, spiral swarfs or spiral swarf pieces are avoided.

Processing information for floating points on cladding panels Stop fastening as soon as the screw head connects to the surface and turn the screw back a quarter turn in order to remove the clamp load from the connection.

Technical specifications Diameter Drilling capacity (tI pre-drilled) + tII Drive Head diameter Head height

5.5 mm 1.5 mm Hexalobular TX25 16 mm 2.0 mm

11


Rear ventilated facades Self-drilling screws

EJOT® self-drilling screw JT4-LT-XT-3H/4-5.5x19 16 mm

TX25 SCAN TO SHOP

Length [mm]

NEW

max. panel thickness [mm]

Self-drilling screw 19 2-3 Centring bushes 2-3 2-3

Price/100 Order description [EUR]

EAN

500

JT4-LT-XT-3H/4-5.5x19 KD16 7 384 219 300

4061245044507

500 500

Centring bush Ø 11/2 F Centring bush Ø 11/2 S

4061245010212 4061245018508

Application range ll For fastening facade panels to aluminium substructures ≤ 2.0 mm, for example Novelis ff2® ll Can be combined with LT fixed and floating point sleeves Characteristics ll A2 stainless steel ll Pan head Benefits ll To cover slotted holes and large pre-drill diameters ll Also available in RAL lacquering ll Flat screw head for aesthetic facade design ll Wobble-free fastening by using the LT tool ll Easy assembly and reliable sliding thanks to optimised free spin zone ll Centring bush collar protects the surface of the facade panel from scratches ll No rivet installation gauge or drilling gauge necessary ll XT cutting ring under the screw head facilitates easy removal of the protective film during the forming of fixed points without centring bush ll Thread-free part under the screw head allows an intentional further rotation of the screw head after connecting surface

12

Article number

3 010 005 700 3 010 006 700

Note Please note the respective approval of the facade panel and the assembly instructions of the manufacturer. Technical specifications Diameter Drilling capacity (tI pre-drilled) + tII Drive head diameter Head height Free spin zone Pre-drilling diameter sleeves

5.5 mm 1.5-3.0 mm Hexalobular TX25 16 mm 2.0 mm 4 mm 11 mm

www.ejot.com


Rear ventilated facades Self-drilling screws

EJOT® self-drilling screw JT4-LT-XT-3H/6-5.5x25 TX25

16 mm

SCAN TO SHOP

P-S 18 0447

NEW Length [mm]

max. panel thickness onto timber / aluminium [mm]

Self-drilling screw 25 Centring bushes 4 4

Price/100 Order description [EUR]

EAN

500

JT4-LT-XT-3H/6-5.5x25 KD16 7 384 216 300

4061245044538

500 500

XT centring bush Ø11/4 F XT centring bush Ø11/4 S

4061245044552 4061245044545

Application range ll For fastening plain aluminium composite panels to aluminium substructures ll Can be combined with XT fixed and floating point sleeves Characteristics ll A2 stainless steel ll Pan head Benefits ll To cover slotted holes and large pre-drill diameters ll Also available in RAL lacquering ll Flat screw head for aesthetic facade design ll Easy assembly and reliable sliding thanks to optimised free spin zone ll Regulated by the building authorities in test certificate P-S 18 0447 ll Easy removal of protective film ll Centring bush collar protects the surface of the facade panel from scratches ll No rivet installation gauge or drilling gauge necessary

3 010 013 700 3 010 014 700

ll T hread-free part under the screw head allows an intentional further rotation of the screw head after connecting surface Note Please note the respective approval of the facade panel and the assembly instructions of the manufacturer.

Technical specifications Diameter Drilling capacity (tI pre-drilled) + tII Drive Head diameter Head height Free spin zone Pre-drilling diameter sleeves

1

2

3

4

www.ejot.com

Article number

5.5 mm 2.0-3.0 mm Hexalobular TX25 16 mm 2.0 mm 6.0 mm 11 mm

Assembly of the XT system 1. Place XT centring bush in predrilled facade panel 2. Rotate XT centring bush with LT-XT tool in order to cut the protective film 3. Fasten LT-XT screw with LT-XT tool in support profile 4. Remove protective film gently over the fixing point

13


Rear ventilated facades Self-drilling screws

EJOT® self-drilling screw JT3-LT-3-5.5x30 TX25

16 mm

SCAN TO SHOP

ETA-10/0200

Length [mm]

max. panel thickness [mm]

30

12

Price/100 Order description [EUR] 500

Application range ll Fastening facade panels to 1.5-2.5 mm aluminium and steel substructures ll Can be combined with LT fixed and floating point sleeves Characteristics ll A2 stainless steel with hardened drill point ll Pan head Benefits ll To cover slotted holes and large pre-drill diameters ll Also available in RAL lacquering ll Flat screw head for aesthetic facade design ll Wobble-free fastening by using the LT tool

14

JT3-LT-3-5.5x30 KD16

Article number

EAN

7 384 211 301

4061245014012

Note Please note the respective approval of the facade panel and the assembly instructions of the manufacturer. Processing information for floating points on cladding panels Stop fastening as soon as the screw head connects to the surface and turn the screw back a quarter turn in order to remove the clamp load from the connection.

Technical specifications Diameter Drilling capacity (tI pre-drilled) + tII Drive Head diameter Head height

5.5 mm 1.5 - 2.5 mm Hexalobular TX25 16 mm 2.0 mm

www.ejot.com


Rear ventilated facades Self-drilling screws

EJOT® self-drilling screw JT4-LT-2/6-6.0x50 TX25

16 mm

SCAN TO SHOP

ETA-10/0200

Length [mm]

max. panel thickness onto timber / aluminium [mm]

50

10 / 26

Price/100 Order description [EUR] 500

Application range ll Fastening facade panels to aluminium or timber substructures ll Can be combined with LT fixed and floating point sleeves Characteristics ll A2 stainless steel ll Pan head Benefits ll To cover slotted holes and large pre-drill diameters ll Also available in RAL lacquering ll Flat screw head for aesthetic facade design ll No pre-drilling of the timber substructure ll G ood drilling behaviour even in areas of branches ll Wobble-free fastening by using the LT tool

www.ejot.com

JT4-LT-2/6-6.0x50 KD16

Article number

EAN

7 384 206 300

4061245014036

Note Please note the respective approval of the facade panel and the assembly instructions of the manufacturer. Processing information for floating points on cladding panels Stop fastening as soon as the screw head connects to the surface and turn the screw back a quarter turn in order to remove the clamp load from the connection.

Technical specifications Diameter Drilling capacity (tI pre-drilled) + tII Drive Head diameter Head height Length non-threaded part

6.0 mm 1.5-2.0 mm Hexalobular TX25 16 mm 2.0 mm 6.0 mm

15


Rear ventilated facades Centring bushes

EJOT® centring bush F (fixed point) SCAN TO SHOP

Panel thickness [mm] 2 4 6 8

Price/100 Order description [EUR] 500 500 500 500

Centring bush Ø 11/2 F Centring bush Ø 11/4 F Centring bush Ø 11/6 F Centring bush Ø 11/8 F

Application range ll Fastening facade panels in combination with LT screws with head diameter 16 mm ll To form fixed points Characteristics ll Grey coloured plastic ll For panel thickness 2 / 4 / 6 / 8 mm ll UV-resistant Benefits ll All holes in the panel are produced with the same diameter (11 mm), which can be done efficiently at the shop floor ll No rivet installation gauge, no drilling gauge necessary ll Fast assembly in combination with LT screws ll Easily revisionable panel fastening ll The 0.5 collar of the bush prevents direct contact between screw head and panel surface ll The hole in the middle serves for the centered positioning of the screw

16

Article number

EAN

3 010 005 700 3 010 009 700 3 010 011 700 3 010 007 700

4061245010212 4061245018478 4061245018454 4061245018492

Note Usability of bushes and LT screws must be agreed with the respective panel manufacturer. Please note the respective approval of the facade panel and the assembly instructions of the manufacturer.

Technical specifications Bush internal hole Ø Facade panel drill hole Ø

5.8 mm 11.0 mm

www.ejot.com

NEW


Rear ventilated facades Centring bushes

EJOT® centring bush S (floating point) SCAN TO SHOP

Panel thickness [mm] 2 4 6 8

Price/100 Order description [EUR] 500 500 500 500

Centring bush Ø 11/2 S Centring bush Ø 11/4 S Centring bush Ø 11/6 S Centring bush Ø 11/8 S

Application range ll Fastening facade panels in combination with LT screws with head diameter 16 mm ll To form floating points Characteristics ll Black coloured plastic ll For panel thickness 2 / 4 / 6 / 8 mm ll UV-resistant Benefits ll All holes in the panel are produced with the same diameter (11 mm), which can be done efficiently at the shop floor ll No rivet installation gauge, no drilling gauge necessary ll Fast assembly in combination with LT screws ll Easily revisionable panel fastening ll The 0.5 collar of the bush prevents direct contact between screw head and panel surface, thus no scratches on the panel surface even during thousandfold relative displacement ll The bottom of the bush which is only 0.3 mm thin is abraded due to relative displacement ll The hole in the middle serves for the centered positioning of the screw

www.ejot.com

Article number

EAN

3 010 006 700 3 010 010 700 3 010 012 700 3 010 008 700

4061245018508 4061245018461 4061245018447 4061245018485

NEW

Note Usability of bushes and LT screws must be agreed with the respective panel manufacturer. Please note the respective approval of the facade panel and the assembly instructions of the manufacturer. Processing information for screws with full thread Stop fastening as soon as the screw head connects to the surface and turn the screw back a quarter turn in order to remove the clamp load from the connection.

Technical specifications Bush internal hole Ø Facade panel drill hole Ø

8.6 mm 11.0 mm

17


Rear ventilated facades Self-drilling screws

EJOT® self-drilling screw JT4-FR-2H/6-4.8 TX25 SCAN TO SHOP

Length [mm]

Z-10.3-774

[mm]

Price/100 Order description [EUR]

Self-drilling screw 22 6 1,000 Centring bush 500 *JT9 made of A4 stainless steel upon request

Article number

EAN

JT4-FR-2H/6-4.8x22*

7 384 170 300

4061245014050

Centring bush

3 010 003 700

4061245010205

Application range ll Fastener for ALUCOBOND® external wall cladding according to Z-10.3-774 ll For fastening without forcing tension to 2 mm aluminium substructures Characteristics ll A2 stainless steel ll With centring bush to form floating points Benefits ll Centred drilling and simultaneous fastening of the boards to the substructure ll No pre-drilling of the substructure ll Thread-free part under the screw head allows an intentional further rotation of the screw head after surface connection

18

Note We recommend the tapered special bit hexalobular TX25W-1/4“/Cx25 for force fit in the fastener head. To form fixed points, we recommend pre-drilling a Ø 4.0 mm hole in the panel.

Technical specifications Diameter Drilling capacity tI + tII Drive Head diameter Head height Ø drill hole centring bush

4.8 mm 1.0 + 3.0 mm Hexalobular TX25 12 mm 3.4 mm 8.5 mm

www.ejot.com


Rear ventilated facades Self-drilling screws

EJOT® self-drilling screw JT4-XT TX25 SCAN TO SHOP

Length [mm] 21

Z-10.3-774

For panel thickness [mm] 4.0

Price/100 [EUR] 500

Application range ll Fastener between the reinforcing profile and an ALUCOBOND® cassette according to Z-10.3-774 Characteristics ll A2 stainless steel Benefits/Operating principle ll Fastener pierces the ALUCOBOND panel and the aluminium substructure ll Thread-free part under the screw head allows an intentional further rotation of the screw head after surface connection ll Cutting ring under the screw head cuts protective film on the facade panel ll Protective film can be removed from the ALUCOBOND® panel without residue after assembly ll Also available as laquered version

www.ejot.com

Order description

Article number

EAN

JT4-XT-3/6-6.0x21

7 384 213 300

4061245013992

Technical specifications Diameter Drilling capacity tI + tII Drive Head diameter Head height Free spin zone

6.0 mm 2.0 mm Hexalobular TX25 11 mm 2.5 mm 6.0 mm

Watch the video now: https://youtu.be/RKUPO7xTQ8c

19


Rear ventilated facades Self-drilling screws

EJOT® self-drilling screw JT4-S-2-4.8 TX25 SCAN TO SHOP

P-BWU02168012

Length [mm]

For timber thickness [mm]

38 48

20 - 30 30 - 40

Price/100 Order description [EUR] JT4-S-2-4.8x38 JT4-S-2-4.8x48

500 500

Article number

EAN

7 382 086 300 7 382 072 300

4061245014197 4061245014203

Technical specifications Diameter Drilling capacity tI + tII Drive Installation rotation speed

Application range ll Fastening timber laths to aluminium substructure ≤ 2 mm Characteristics ll A2 stainless steel ll Countersunk head with milling ribs

4.8 mm 2.0 mm Hexalobular TX25 max. 1800 rpm

EJOT® self-drilling screw JT4-STS-3-4.8 TX25 SCAN TO SHOP

Length [mm]

For panel thickness [mm]

35

0 - 25

Price/100 Order description [EUR] 500

Application range ll Fastening plaster-base sheeting to aluminium substructures ≤ 3 mm Characteristics ll A2 stainless steel ll Countersunk head with flange

JT4-STS-3-4.8x35

Article number

EAN

7 384 094 300

4061245014074

Technical specifications Diameter Drilling capacity tI + tII Head diameter Drive

4.8 mm 3.0 mm 12 mm Hexalobular TX25

Benefits ll Very flat head ll Wobble-free fastening with LT-STS Tool

20

www.ejot.com


Rear ventilated facades Facade anchors

Range of lengths anchors with screws made of steel with zinc-plated Cr(VI)-free coating (-V) or made of A4 stainless steel Anchor type Material

SDF-S 8V -V

-E

SDF-KB 8V -V

-E

SDF-S 10V -V

-E

SDF-KB 10V -V

-E

• • • • • • • • •

• • •

• • • • • •

• • • • • • • • •

•1) •1)

• •

• •

SDF-S 10H

SDF-KB 10H

-V

-E

-V

-E

• • • • • •

• • • • • •

• • • • • •

• • • • • •

• • • • • •

• • • • • •

• •

• •

SDF-S 14A -V

SDF-KB 14A

-E

SDP-S 10G

SDP-KB 10G

-V

-E

-V

-E

-V

-E

• •

• •

• • • • • •

• • • • • •

• • • • • •

• • • • • •

• •

•1) •1)

• •

•1) •1)

Length [mm]

50 60 70 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360

• • • • • • • •1) •1)

• • • • • • •1) • •1) • • • •

1) Delivery time upon request

Approval Anchor type Nominal drill diameter Drill cut diameter Drill hole depth Embedment depth (concrete + masonry) Embedment depth (concrete) Embedment depth (masonry) Hole diameter of the component to be installed

dcut [mm] ≤ h1 / t [mm] ≥ hnom / hv [mm] ≥ hnom,1 / hv [mm] ≥ hnom,2 / hv [mm] ≥ df [mm]

Building materials Standard concrete ≥ C12/15 Solid brick Mz EN 77-1-001 Vertically perforated brick Hlz EN 771-1-002 Vertically perforated brick LHlz1) Solid sand-lime brick KS EN 771-2-009 Perforated sand-lime brick KSL EN 771-2-003 Slag brick 1) Lightweight concrete cavity block ≥ HBL 2 EN 771-3-005 Solid lightweight concrete bricks Solid concrete brick1) EN 771-3-006 Concrete cavity block1) Concrete rain screen ≥ C 12/15 Aerated concrete EN 771-4

Standard DIN 1045 EN 12 DIN EN 772 DIN 1051 DIN 1052 DIN 106 DIN 106 DIN 398 DIN 18151 DIN 18152 DIN 18153 DIN 18153 DIN 1045 DIN 1053 / 4165

dnom / dD [mm]

ETA-15/0387 SDF-8V 8 8.45 60 50 50 50 8.5

ETA-10/0305 SDF-10V SDF-10H 10 10 10.45 10.45 50 / 60 80 – 70 40 70 50 70 10.5 10.5

SDF-8V • •

SDF-10V • •

(•)

•

(•) (•)

ETA-15/0027 SDF-14A 14 14.5 80 70 70 70 14.5

ETA-12/0502 SDP-10G 10 10.45 80 70 70 70 10.5

SDF-10H • • • • • •

SDF-14A • • •

SDP-10G

• •

•

• •

• • •

•

•

1) As a rule: pull-out tests on the structure Note: Please observe the corresponding approvals for determining the characteristic load-carrying capacity.

www.ejot.com

21


Rear ventilated facades Facade anchors

EJOT® facade anchor SDF-S-8V TX30 SCAN TO SHOP

Fastening Anchor length L thickness tfix ≤ [mm] [mm]

ETA-15/0387

Price/100 Order description [EUR]

Article number

EAN

Anchors with steel screws with zinc-plated Cr(VI)-free coating (-V) 80 30 100 SDF-S-8Vx80-V 100 50 50 SDF-S-8Vx100-V 120 70 50 SDF-S-8Vx120-V 140 90 50 SDF-S-8Vx140-V 160 110 50 SDF-S-8Vx160-V 180 130 50 SDF-S-8Vx180-V 200 150 50 SDF-S-8Vx200-V* 220 170 50 SDF-S-8Vx220-V* * Delivery time upon request

8 569 080 430 8 569 100 430 8 569 120 430 8 569 140 430 8 569 160 430 8 569 180 430 8 569 200 430 8 569 220 430

4061245019123 4061245019116 4061245019109 4061245019093 4061245019086 4061245019079 4061245019062 4061245019055

Application range ll The cost-effective alternative for embedding timber substructures to solid brick masonry and concrete Characteristics ll Countersunk head ll Small drill-hole diameter ll Product identification through different sleeve colours Note For planning and processing, please observe ETA-15/0387

Characteristic values Diameter Drive Drill hole depth ≥ h1 Embedment depth ≥ hnom

8.0 mm Hexalobular TX30 60 mm 50 mm

Characteristic loads* Tensile strength NRk,p in concrete < C16/20 Tensile strength NRk,p in concrete ≥ C16/20 Brick Mz 28-1.8, NF Solid lime sand brick KS, NF 20-2.0 Transverse strength VRk,s Anchor with steel screw Bending moment MRk,s Anchor with steel screw

4.50 kN 6.50 kN 2.50 kN 2.00 kN 5.30 kN 8.20 Nm

*applies to temperature range 30-50 °C / 50-80 °C Instructions for using galvanic zinc-plated facade anchor screws (excerpt from ETA-15/0387) The special screw made of galvanic zinc-plated steel may also be used outside, after careful installation and if the area of the screw head is protected against moisture and driving rain in such a way, that no moisture can enter the anchor shaft. This requires facade cladding or a rain screen fixed in front of the screw head and the screw head has to be coated with a soft-plastic, permanently elastic, bitumen oil combination coat (e.g. car underbody coating or cavity protection).

22

www.ejot.com


Rear ventilated facades Facade anchors

EJOT® facade anchor SDF-KB-8V SCAN TO SHOP

AF10

Fastening Anchor length L thickness tfix ≤ [mm] [mm]

ETA-15/0387

Price/100 Order description [EUR]

Anchors with steel screws with zinc-plated Cr(VI)-free coating (-V) 60 10 100 SDF-KB-8Vx60-V 80 30 100 SDF-KB-8Vx80-V 100 50 50 SDF-KB-8Vx100-V 120 70 50 SDF-KB-8Vx120-V 140 90 50 SDF-KB-8Vx140-V 160 110 50 SDF-KB-8Vx160-V 180 130 50 SDF-KB-8Vx180-V 200 150 50 SDF-KB-8Vx200-V* 220 170 50 SDF-KB-8Vx220-V* * Delivery time upon request Application range ll For the embedment of metal substructures in solid brick masonry and concrete Characteristics ll Hexagon head with flange ll Small drill-hole diameter ll Thermal and electrical isolation ll Product identification through different sleeve colours Note For planning and processing, please observe ETA-15/0387

Article number

EAN

8 570 060 430 8 570 080 430 8 570 100 430 8 570 120 430 8 570 140 430 8 570 160 430 8 570 180 430 8 570 200 430 8 570 220 430

4061245019048 4061245019024 4061245019000 4061245018997 4061245018980 4061245018973 4061245018966 4061245018959 4061245018942

Characteristic values Diameter Drive Drill hole depth ≥ h1 Embedment depth ≥ hnom

8.0 mm Hexagon A/F10 60 mm 50 mm

Characteristic loads* Tensile strength NRk,p in concrete < C16/20 Tensile strength NRk,p in concrete ≥ C16/20 Brick Mz 28-1.8, NF Solid lime sand brick KS, NF 20-2.0 Transverse strength VRk,s Anchor with steel screw Bending moment MRk,s Anchor with steel screw

4.50 kN 6.50 kN 2.50 kN 2.00 kN 5.30 kN 8.20 Nm

*applies to temperature range 30-50 °C / 50-80 °C

www.ejot.com

23


Rear ventilated facades Facade anchors

EJOT® facade anchor SDF-S-10V TX40 SCAN TO SHOP

Anchor length L [mm]

ETA-10/0305

Fastening thickness tfix (concrete / masonry) ≤ [mm]

Price/100 Order description [EUR]

Anchors with steel screws with zinc-plated Cr(VI)-free coating (-V) 50 10 / 100 SDF-S-10Vx50-V 60 20 / 10 100 SDF-S-10Vx60-V 70 30 / 20 100 SDF-S-10Vx70-V 80 40 / 30 100 SDF-S-10Vx80-V 100 60 / 50 50 SDF-S-10Vx100-V 120 80 / 70 50 SDF-S-10Vx120-V 140 100 / 90 50 SDF-S-10Vx140-V 160 120 / 110 50 SDF-S-10Vx160-V 180 140 / 130 50 SDF-S-10Vx180-V 200 160 / 150 50 SDF-S-10Vx200-V 220 180 / 170 50 SDF-S-10Vx220-V Application range ll Installation of timber or metal attachments ll For non-supporting redundant systems ach cording to ETAG 020 h1 nom ll Suitable for the structural fastening of hgates, doors, windows, square timber

Concrete

h

h1,1 hnom,1

t fix t tol

Masonry

h

24

h1,2 hnom,2

t fix t tol

Characteristics ll Countersunk head ll Anchor with an embedment depth of 40 mm in concrete ll Two installation depths (embedment in masonry 50 mm) h ll Very short expansion t fix part for extremely fast h1 h t tol h1,2 hnom t fix installation hnom,2 t tol ll Optimal expanding part due to radial expansion ll Very high bending moment ll Product identification through different sleeve colours ll Double safety lock against torsion for secure installation Note Please observe European Technical Approval ETA-10/0305 in the planning and processing of products. Further information about parameters and loads can be found in the approval.

t tol

t fix

Article number

EAN

8 580 050 450 8 580 060 450 8 580 070 450 8 580 080 450 8 580 100 450 8 580 120 450 8 580 140 450 8 580 160 450 8 580 180 450 8 580 200 450 8 580 220 450

4061245018935 4061245018928 4061245018911 4061245018904 4061245018898 4061245018881 4061245018874 4061245018867 4061245018850 4061245018843 4061245018836

Characteristic values Diameter Hole depth in concrete h1.1 Effective Embedment depth in concrete hnom,1 Hole depth in masonry h1.2 Effective Embedment depth in masonry hnom,2 Drill hole diameter d0 Through hole diameter of component to be attached df Drive

10 mm ≥ 50 mm ≥ 40 mm ≥ 60 mm ≥ 50 mm 10 mm ≤ 10.5 mm TX40

Characteristic loads Tensile load NRk,p in concrete C12/15 Temperature range 30 °C / 50 °C 4.50 kN Temperature range 50 °C / 80 °C 4.00 kN FRk brick Mz 20-1.8, NF 2.50 kN FRk solid sand-lime brick KS 36, NF 4.00 kN 4.50 kN FRk solid sand-lime brick KS 20, 8 DF Transverse load VRk,s in concrete C12/15 at hnom,1 = 40 mm Anchor with steel screw 7.93 kN Transverse load VRk,s at hnom,2 = 50 mm Anchor with steel screw 11.09 kN Bending moment MRk,s at hnom,1 =40 mm Anchor with steel screw 13.80 kN Side load MRk,s at hnom,2 = 50 mm Anchor with steel screw 23.01 Nm

www.ejot.com


Rear ventilated facades Facade anchors

EJOT® facade anchor SDF-KB-10V AF13/TX40

SCAN TO SHOP

Anchor length L [mm]

ETA-10/0305

Fastening thickness tfix (concrete / masonry) ≤ [mm]

Price/100 Order description [EUR]

Anchors with steel screws with zinc-plated Cr(VI)-free coating (-V) 50 10 / 100 SDF-KB-10Vx50-V 60 20 / 10 100 SDF-KB-10Vx60-V 70 30 / 20 100 SDF-KB-10Vx70-V 80 40 / 30 100 SDF-KB-10Vx80-V 100 60 / 50 50 SDF-KB-10Vx100-V 120 80 / 70 50 SDF-KB-10Vx120-V 140 100 / 90 50 SDF-KB-10Vx140-V 160 120 / 110 50 SDF-KB-10Vx160-V 180 140 / 130 50 SDF-KB-10Vx180-V 200 160 / 150 50 SDF-KB-10Vx200-V 220 180 / 170 50 SDF-KB-10Vx220-V Anchor with A4 stainless steel screw (-E) 50 10 / 100 SDF-KB-10Vx50-E 60 20 / 10 100 SDF-KB-10Vx60-E 70 30 / 20 100 SDF-KB-10Vx70-E

Article number

EAN

8 581 050 450 8 581 060 450 8 581 070 450 8 581 080 450 8 581 100 450 8 581 120 450 8 581 140 450 8 581 160 450 8 581 180 450 8 581 200 450 8 581 220 450

4061245018829 4061245018805 4061245018775 4061245018751 4061245018744 4061245018737 4061245018720 4061245018713 4061245018706 4061245018690 4061245018683

8 581 050 650 8 581 060 650 8 581 070 650

4061245018812 4061245018799 4061245018768 h

Application range ll Installation of metal attachments ll For non-supporting redundant systems according to ETAG 020 ll Suitable for the structural fastening of wall cupboards, cladding, metal angle pieces

Characteristic values Diameter Hole depth in concrete h1.1 Effective Embedment depth in concrete hnom,1 Hole depth in masonry h1.2 Effective Embedment depth in masonry hnom,2 Drill hole diameter d0

Characteristics ll Hexagon head with flange ll Anchor with an embedment depth of 40 mm in concrete ll Two installation depths (embedment in masonry 50 mm) ll Very short expansion part for extremely fast installation ll Optimal expanding part due to radial expansion ll Very high bending moment ll Product identification through different sleeve colours ll Double safety lock against torsion for secure installation

Through hole diameter of component to be attached df

≤ 10.5 mm

Drive

AF13/TX40

Note Please observe European Technical Approval ETA-10/0305 in the planning and processing of products. Further information about parameters and loads can be found in the approval.

www.ejot.com

h

h1,1 hnom,1

10 mm ≥ 50 mm ≥ 40 mm ≥ 60 mm ≥ 50 mm 10 mm

t fix Characteristic loads h1,1 hnom,1 t tol Tensile load NRk,p in concrete C12/15 Temperature range 30 °C / 50 °C 4.50 kN Temperature range 50 °C / 80 °C 4.00 kN 2.50 kN FRk brick Mz 20-1.8, NF FRk solid sand-lime brick KS 36, NF 4.00 kN FRk solid sand-lime brick KS 20, 8 DF 4.50 kN Transverse load VRk,s in concrete C12/15 at hnom,1 = 40 mm Anchor with steel screw 7.93 kN Anchor with A4 stainless steel screw 9.12 kN Transverse load VRk,s at hnom,2 = 50 mm Anchor with steel screw 11.09 kN Anchor with A4 stainless steel screw 12.94 kN Bending moment MRk,s at hnom,1 =40 mm Anchor with steel screw 13.80 kN Anchor with A4 stainless steel screw 16.09 kN Side load MRk,s at hnom,2 = 50 mm Anchor with steel screw 23.01 Nm Anchor with A4 stainless steel screw 26.62 Nm

t fix t tol

Concrete

h

h1,2 hnom,2

t fix t tol

Masonry

25


Rear ventilated facades Facade anchors

EJOT® Universal anchor SDF-S-10H TX40 SCAN TO SHOP

Fastening Anchor length L thickness tfix ≤ [mm] [mm]

ETA-10/0305

Price/100 Order description [EUR]

Anchors with steel screws with zinc-plated Cr(VI)-free coating (-V) 80 10 100 SDF-S-10Hx80-V 100 30 50 SDF-S-10Hx100-V 120 50 50 SDF-S-10Hx120-V 140 70 50 SDF-S-10Hx140-V 160 90 50 SDF-S-10Hx160-V 180 110 50 SDF-S-10Hx180-V 200 130 50 SDF-S-10Hx200-V 220 150 50 SDF-S-10Hx220-V 240 170 50 SDF-S-10Hx240-V 260 190 50 SDF-S-10Hx260-V 280 210 50 SDF-S-10Hx280-V 300 230 50 SDF-S-10Hx300-V Application range ll Installation of timber or metal attachments

h

h1 hnom

t tol

t fix

Installation substrate

x

Note Please observe European Technical Approval ETA-10/0305 in the planning and processing of products. Further information about parameters and loads can be found in the approval.

ll F or non-supporting redundant systems according to ETAG 020 ll Suitable for the structural fastening of gates, doors, windows, square timber ll For embedment in rain screens Characteristics ll Countersunk head ll Approved for all common building materials ll Reliable hold in problematic building materials thanks to optimised expansion part ll Radial expansion for reliable hold ll Product identification through different sleeve colours ll Double safety lock against torsion for secure installation

Article number

EAN

8 510 080 420 8 510 100 420 8 510 120 420 8 510 140 420 8 510 160 420 8 510 180 420 8 510 200 420 8 510 220 420 8 510 240 420 8 510 260 420 8 510 280 420 8 510 300 420

4061245019864 4061245019840 4061245019826 4061245019802 4061245019789 4061245019765 4061245019741 4061245019727 4061245019703 4061245019680 4061245019666 4061245019659

Characteristic values Diameter Hole depth in concrete h1.1 Effective embedment depth hnom Drill hole diameter d0 Through hole diameter of component to be attached df Drive

10 mm ≥ 80 mm ≥ 70 mm 10 mm ≤ 10.5 mm TX40

Characteristic loads Tensile load NRk,p in concrete C12/15 Temperature range 30 °C / 50 °C Temperature range 50 °C / 80 °C Brick Mz 20-1.8, NF Solid sand-lime brick KS 36, NF Solid sand-lime brick KS 20, 8 DF Solid lightweight concrete brick V6, 2 DF Vertically perforated brick HLz 12-0.9, NF Perforated sand-lime brick KSL 12, 4 DF Cavity block made of lightweight concrete Hbl 10, 12 DF

4.50 kN 4.00 kN 4.00 kN 4.50 kN 4.50 kN 2.00 kN 2.00 kN 2.50 kN 1.20 kN

Transverse load VRk,s Anchor with steel screw 9.35 kN Anchor with A4 stainless steel screw 10.91 kN Bending moment MRk,s Anchor with steel screw 17.67 Nm Compressive strength of aerated concrete [N/mm2] 30 - 50 °C Aerated concrete 4 1.5 kN Aerated concrete 5 2.0 kN Aerated concrete 6 2.5 kN Aerated concrete 7 2.5 kN Partial safety factor γMAAC 2.0

26

www.ejot.com


Rear ventilated facades Facade anchors

EJOT® Universal anchor SDF-S-10H TX40 SCAN TO SHOP

Fastening Anchor length L thickness tfix ≤ [mm] [mm]

ETA-10/0305

Price/100 Order description [EUR]

Anchor with A4 stainless steel screw (-E) 80 10 100 100 30 50 120 50 50 140 70 50 160 90 50 180 110 50 200 130 50 220 150 50 240 170 50 260 190 50 280 210 50 300 230 50

SDF-S-10Hx80-E SDF-S-10Hx100-E SDF-S-10Hx120-E SDF-S-10Hx140-E SDF-S-10Hx160-E SDF-S-10Hx180-E SDF-S-10Hx200-E SDF-S-10Hx220-E SDF-S-10Hx240-E SDF-S-10Hx260-E SDF-S-10Hx280-E SDF-S-10Hx300-E

Application range ll Installation of timber or metal attachments ll F or non-supporting redundant systems according to ETAG 020 ll Suitable for the structural fastening of gates, doors, windows, square timber ll For embedment in rain screens Characteristics ll Countersunk head ll Approved for all common building materials ll Reliable hold in problematic building materials thanks to optimised expansion part ll Radial expansion for reliable hold ll Product identification through different sleeve colours ll Double safety lock against torsion for secure installation

Characteristic values Diameter Hole depth in concrete h1.1 Effective embedment depth hnom Drill hole diameter d0 Through hole diameter of component to be attached df Drive

www.ejot.com

10 mm ≥ 80 mm ≥ 70 mm 10 mm

Article number

EAN

8 510 080 620 8 510 100 620 8 510 120 620 8 510 140 620 8 510 160 620 8 510 180 620 8 510 200 620 8 510 220 620 8 510 240 620 8 510 260 620 8 510 280 620 8 510 300 620

4061245019857 4061245019833 4061245019819 4061245019796 4061245019772 4061245019758 4061245019734 4061245019710 4061245019697 4061245019673 4061245031514 4061245031521

Characteristic loads Tensile load NRk,p in concrete C12/15 Temperature range 30 °C / 50 °C Temperature range 50 °C / 80 °C Brick Mz 20-1.8, NF Solid sand-lime brick KS 36, NF Solid sand-lime brick KS 20, 8 DF Solid lightweight concrete brick V6, 2 DF Vertically perforated brick HLz 12-0.9, NF Perforated sand-lime brick KSL 12, 4 DF h made of lightweight concrete Cavity block t h Hbl 10, 12 DFh t 1,1

nom,1

fix

tol

NEW NEW NEW NEW

h

4.50 kN 4.00 kN 4.00 kN 4.50 kN 4.50 kN 2.00 kN 2.00 kN 2.50 kN h

h1.20 1,2 hnom,2

kNt

h1 hnom

t tol

t fix

Installation substrate fix

t tol

Transverse load VRk,s Anchor with steel screw 9.35 kN Anchor with A4 stainless steel screw 10.91 kN Bending moment MRk,s Anchor with A4 stainless steel screw 20.62 Nm Compressive strength of aerated concrete [N/mm2] 30 - 50 °C Aerated concrete 4 1.5 kN Aerated concrete 5 2.0 kN Aerated concrete 6 2.5 kN Aerated concrete 7 2.5 kN Partial safety factor γMAAC 2.0

Note Please observe European Technical Approval ETA-10/0305 in the planning and processing of products. Further information about parameters and loads can be found in the approval.

≤ 10.5 mm TX40

27


Rear ventilated facades Facade anchors

EJOT® Universal anchor SDF-KB-10H SCAN TO SHOP

AF13/TX40

Fastening Anchor length L thickness tfix ≤ [mm] [mm]

ETA-10/0305

Price/100 Order description [EUR]

Anchors with steel screws with zinc-plated Cr(VI)-free coating (-V) 80 10 100 SDF-KB-10Hx80-V 100 30 50 SDF-KB-10Hx100-V 120 50 50 SDF-KB-10Hx120-V 140 70 50 SDF-KB-10Hx140-V 160 90 50 SDF-KB-10Hx160-V 180 110 50 SDF-KB-10Hx180-V 200 130 50 SDF-KB-10Hx200-V 220 150 50 SDF-KB-10Hx220-V h

x

Installation substrate

h1 hnom

t tol

t fix

Application range ll Installation of metal attachments ll For non-supporting redundant systems according to ETAG 020 ll Suitable for the structural fastening of wall cupboards, cladding, metal angle pieces ll For embedment in rain screens Characteristics ll Hexagon head with flange ll Approved for all common building materials ll Reliable hold in problematic building materials thanks to optimised expansion part ll Radial expansion for reliable hold ll Product identification through different sleeve colours ll Double safety lock against torsion for secure installation Note Please observe European Technical Approval ETA-10/0305 in the planning and processing of products. Further information about parameters and loads can be found in the approval.

28

Article number

EAN

8 513 080 420 8 513 100 420 8 513 120 420 8 513 140 420 8 513 160 420 8 513 180 420 8 513 200 420 8 513 220 420

4061245019642 4061245019611 4061245019581 4061245019567 4061245019543 4061245019529 4061245019505 4061245019482

Characteristic values Diameter Hole depth in concrete h1.1 Effective embedment depth hnom Drill hole diameter d0

10 mm ≥ 80 mm ≥ 70 mm 10 mm

Through hole diameter of component to be attached df

≤ 10.5 mm

Drive

AF13/TX40

Characteristic loads Tensile load NRk,p in concrete C12/15 Temperature range 30 °C / 50 °C Temperature range 50 °C / 80 °C Brick Mz 20-1.8, NF Solid sand-lime brick KS 36, NF Solid sand-lime brick KS 20, 8 DF Solid lightweight concrete brick V6, 2 DF Vertically perforated brick HLz 12-0.9, NF Perforated sand-lime brick KSL 12, 4 DF Cavity block made of lightweight concrete Hbl 10, 12 DF

4.50 kN 4.00 kN 4.00 kN 4.50 kN 4.50 kN 2.00 kN 2.00 kN 2.50 kN 1.20 kN

Transverse load VRk,s Anchor with steel screw 9.35 kN Anchor with A4 stainless steel screw 10.91 kN Bending moment MRk,s Anchor with steel screw 17.67 Nm Anchor with A4 stainless steel screw 20.62 Nm Compressive strength of aerated concrete [N/mm2] 30 - 50 °C Aerated concrete 4 1.5 kN Aerated concrete 5 2.0 kN Aerated concrete 6 2.5 kN Aerated concrete 7 2.5 kN Partial safety factor γMAAC 2.0

www.ejot.com


Rear ventilated facades Facade anchors

EJOT® Universal anchor SDF-KB-10H SCAN TO SHOP

AF13/TX40

Fastening Anchor length L thickness tfix ≤ [mm] [mm]

ETA-10/0305

Price/100 Order description [EUR]

Anchor with A4 stainless steel screw (-E) 80 10 100 100 30 50 120 50 50 140 70 50 160 90 50 180 110 50 200 130 50 220 150 50 Application range ll Installation of metal attachments ll For non-supporting redundant systems according to ETAG 020 ll Suitable for the structural fastening of wall cupboards, cladding, metal angle pieces ll For embedment in rain screens Characteristics ll Hexagon head with flange ll Approved for all common building materials ll Reliable hold in problematic building materials thanks to optimised expansion part ll Radial expansion for reliable hold ll Product identification through different sleeve colours ll Double safety lock against torsion for secure installation Note Please observe European Technical Approval ETA-10/0305 in the planning and processing of products. Further information about parameters and loads can be found in the approval.

www.ejot.com

SDF-KB-10Hx80-E SDF-KB-10Hx100-E SDF-KB-10Hx120-E SDF-KB-10Hx140-E SDF-KB-10Hx160-E SDF-KB-10Hx180-E SDF-KB-10Hx200-E SDF-KB-10Hx220-E

Article number

EAN

8 513 080 620 8 513 100 620 8 513 120 620 8 513 140 620 8 513 160 620 8 513 180 620 8 513 200 620 8 513 220 620

4061245019635 4061245019604 4061245019574 4061245019550 4061245019536 4061245019512 4061245019499 4061245019475

Characteristic values Diameter Hole depth in concrete h1.1 Effective embedment depth hnom Drill hole diameter d0 h diameter of component to be Through hole t h attached df h t 1,1

nom,1

fix

tol

Drive Characteristic loads Tensile load NRk,p in concrete C12/15 Temperature range 30 °C / 50 °C Temperature range 50 °C / 80 °C Brick Mz 20-1.8, NF Solid sand-lime brick KS 36, NF Solid sand-lime brick KS 20, 8 DF Solid lightweight concrete brick V6, 2 DF Vertically perforated brick HLz 12-0.9, NF Perforated sand-lime brick KSL 12, 4 DF Cavity block made of lightweight concrete Hbl 10, 12 DF

h

h1 hnom

t tol

t fix

10 mm ≥ 80 mm ≥ 70 mm 10 mm h

h ≤ 10.5 mmt 1,2

hnom,2

fix

t tol

AF13/TX40

4.50 kN 4.00 kN 4.00 kN 4.50 kN 4.50 kN 2.00 kN 2.00 kN 2.50 kN

Installation substrate

1.20 kN

Transverse load VRk,s Anchor with steel screw 9.35 kN Anchor with A4 stainless steel screw 10.91 kN Bending moment MRk,s Anchor with steel screw 17.67 Nm Anchor with A4 stainless steel screw 20.62 Nm Compressive strength of aerated concrete [N/mm2] 30 - 50 °C Aerated concrete 4 1.5 kN Aerated concrete 5 2.0 kN Aerated concrete 6 2.5 kN Aerated concrete 7 2.5 kN Partial safety factor γMAAC 2.0

29


Rear ventilated facades Facade anchors

EJOT® facade anchor SDF-S-14A TX40 SCAN TO SHOP

Fastening Anchor length L thickness tfix ≤ [mm] [mm]

h

h1 hnom

t fix t tol

SDF-KB

Ø14A

ETA-15/0027

Price/100 Order description [EUR]

Anchors with steel screws with zinc-plated Cr(VI)-free coating (-V) 120 50 50 SDF-S-14Ax120-V 140 70 50 SDF-S-14Ax140-V 160 90 50 SDF-S-14Ax160-V 180 110 50 SDF-S-14Ax180-V 200 130 50 SDF-S-14Ax200-V 220 150 50 SDF-S-14Ax220-V 240 170 25 SDF-S-14Ax240-V 260 190 25 SDF-S-14Ax260-V 280 210 25 SDF-S-14Ax280-V 300 230 25 SDF-S-14Ax300-V 320 250 25 SDF-S-14Ax320-V 340 270 25 SDF-S-14Ax340-V 360 290 25 SDF-S-14Ax360-V Application range ll Installation of timber or metal attachments

h

h1 hnom

t fix t tol

ll F or non-supporting redundant systems according to ETAG 020 ll Suitable for the structural fastening of gates, doors, windows, square timber

SDF-S

Ø14A

Characteristics ll Countersunk head ll Approved for all common building materials ll Reliable hold in problematic building materials thanks to optimised expansion part ll Radial expansion for reliable hold ll Product identification through different sleeve colours ll Double safety lock against torsion for secure installation Note For planning, please observe approval ETA15/0027.

Article number

EAN

8 591 120 430 8 591 140 430 8 591 160 430 8 591 180 430 8 591 200 430 8 591 220 430 8 591 240 430 8 591 260 430 8 591 280 430 8 591 300 430 8 591 320 430 8 591 340 430 8 591 360 430

4061245018638 4061245018621 4061245018614 4061245018607 4061245018591 4061245018584 4061245018577 4061245018560 4061245018553 4061245018546 4061245018539 4061245018522 4061245018515

Characteristic values Diameter Drive Drill hole depth ≥ t Embedment depth ≥ hv

14 mm Hexalobular TX40 80 mm 70 mm

Characteristic loads* Tensile load NRk,p in concrete > C12/15 Brick Mz 20-1.8, NF Solid lime sand brick KS, 2 DF 20-2.0 Solid lime sand brick KS, 8 DF 20-1.8 Solid brick V, 3 DF Vertically perforated brick HLz, 2 DF 28-1.2 Perforated sand-lime brick KSL, 8 DF 16-1.4 Cavity block tile made of lightweight concrete Hbl, 12 DF Aerated concrete fb ≥ 2 N/mm2 Aerated concrete fb ≥ 4 N/mm2 Aerated concrete fb ≥ 6 N/mm2 Transverse load VRk,s Anchor with steel screw Anchor with A4 stainless steel screw Bending moment MRk,s Anchor with steel screw Anchor with A4 stainless steel screw

8.50 kN 5.50 kN 6.00 kN 7.00 kN 3.00 kN 2.00 kN 2.50 kN 2.00 kN 1.20 kN 2.50 kN 3.50 kN 21.7 kN 25.3 kN 62.5 Nm 72.9 Nm

*applies to temperature range 30-50 °C / 50-80 °C

30

www.ejot.com


Rear ventilated facades Facade anchors

EJOT® facade anchor SDF-KB-14A SCAN TO SHOP

AF17

Fastening Anchor length L thickness tfix ≤ [mm] [mm]

ETA-15/0027

Price/100 Order description [EUR]

Anchors with steel screws with zinc-plated Cr(VI)-free coating (-V) 80 10 50 SDF-KB-14Ax80-V 100 30 50 SDF-KB-14Ax100-V Application range ll Installation of metal attachments ll For non-supporting redundant systems according to ETAG 020 ll Suitable for the structural fastening of wall cupboards, cladding, metal angle pieces Characteristics ll Hexagon head with flange ll Approved for all common building materials ll Reliable hold in problematic building materials thanks to optimised expansion part ll Radial expansion for reliable hold ll Product identification through different sleeve colours ll Double safety lock against torsion for secure installation Note For planning, please observe approval ETA15/0027.

Article number

EAN

8 590 080 430 8 590 100 430

4061245018676 4061245018652

Characteristic values Diameter Drive Drill hole depth ≥ t Embedment depth ≥ hv

14 mm Hexagon A/F17 80 mm 70 mm

Characteristic loads* Tensile load NRk,p in concrete > C12/15 Brick Mz 20-1.8, NF Solid lime sand brick KS, 2 DF 20-2.0 Solid lime sand brick KS, 8 DF 20-1.8 Solid brick V, 3 DF Vertically perforated brick HLz, 2 DF 28-1.2 Perforated sand-lime brick KSL, 8 DF 16-1.4 Cavity block tile made of lightweight concrete Hbl, 12 DF Aerated concrete fb ≥ 2 N/mm2 Aerated concrete fb ≥ 4 N/mm2 Aerated concrete fb ≥ 6 N/mm2 Transverse load VRk,s Anchor with steel screw Anchor with A4 stainless steel screw Bending moment MRk,s Anchor with steel screw Anchor with A4 stainless steel screw

8.50 kN 5.50 kN 6.00 kN 7.00 kN 3.00 kN 2.00 kN 2.50 kN 2.00 kN

h

1.20 kN 2.50 kN 3.50 kN

h1 hnom

t fix t tol

h1 hnom

t fix t tol

SDF-KB

Ø14A

21.7 kN 25.3 kN 62.5 Nm 72.9 Nm

h

*applies to temperature range 30-50 °C / 50-80 °C SDF-S

Ø14A

www.ejot.com

31


Rear ventilated facades Facade anchors

EJOT® facade anchor SDP-S-10G TX40 SCAN TO SHOP

Fastening Anchor length L thickness tfix ≤ [mm] [mm]

ETA-12/0502

Price/100 Order description [EUR]

Anchors with steel screws with zinc-plated Cr(VI)-free coating (-V) 80 10 100 SDP-S-10Gx80-V 100 30 50 SDP-S-10Gx100-V 120 50 50 SDP-S-10Gx120-V 140 70 50 SDP-S-10Gx140-V 160 90 50 SDP-S-10Gx160-V 180 110 50 SDP-S-10Gx180-V 200 130 50 SDP-S-10Gx200-V 220 150 50 SDP-S-10Gx220-V Anchor with A4 stainless steel screw (-E) 80 10 100 SDP-S-10Gx80-E 100 30 50 SDP-S-10Gx100-E 120 50 50 SDP-S-10Gx120-E 140 70 50 SDP-S-10Gx140-E 160 90 50 SDP-S-10Gx160-E 180 110 50 SDP-S-10Gx180-E 200 130 50 SDP-S-10Gx200-E 220 150 50 SDP-S-10Gx220-E Application range ll Fixing wood components in aerated concrete Characteristics ll Countersunk head ll Facade anchor with two-stage screw ll Reliable form-fit in the substrate thanks to combined expansion zones ll High load capacity ll Available with steel screws or stainless steel screws ll P roduct identification through different sleeve colours Note For planning and processing, please observe approval ETA-12/0502.

32

Article number

EAN

8 530 080 420 8 530 100 420 8 530 120 420 8 530 140 420 8 530 160 420 8 530 180 420 8 530 200 420 8 530 220 420

4061245019468 4061245019444 4061245019420 4061245019406 4061245019383 4061245019369 4061245019345 4061245019321

8 530 080 620 8 530 100 620 8 530 120 620 8 530 140 620 8 530 160 620 8 530 180 620 8 530 200 620 8 530 220 620

4061245019451 4061245019437 4061245019413 4061245019390 4061245019376 4061245019352 4061245019338 4061245019314

Characteristic values Diameter Drive Drill hole depth ≥ t Embedment depth ≥ hv

10 mm Hexalobular TX40 80 mm 70 mm

Characteristic values Compressive strength of aerated concrete [N/mm2] Aerated concrete 2 0.75 kN Aerated concrete 3 1.31 kN Aerated concrete 4 1.87 kN Aerated concrete 6 3.00 kN 2.00 Partial safety factor γMAAC Characteristic Bending moment Steel screw 17.7 Nm / γMs 1.50 Stainless steel screw 20.6 Nm / γMs 1.87

www.ejot.com


Rear ventilated facades Facade anchors

EJOT® facade anchor SDP-KB-10G SCAN TO SHOP

AF13/TX40

Fastening Anchor length L thickness tfix ≤ [mm] [mm]

ETA-12/0502

Price/100 Order description [EUR]

Anchors with steel screws with zinc-plated Cr(VI)-free coating (-V) 80 10 100 SDP-KB-10Gx80-V 100 30 50 SDP-KB-10Gx100-V 120 50 50 SDP-KB-10Gx120-V 140 70 50 SDP-KB-10Gx140-V 160 90 50 SDP-KB-10Gx160-V 180 110 50 SDP-KB-10Gx180-V 200 130 50 SDP-KB-10Gx200-V 220 150 50 SDP-KB-10Gx220-V Anchor with A4 stainless steel screw (-E) 80 10 100 SDP-KB-10Gx80-E 100 30 50 SDP-KB-10Gx100-E 120 50 50 SDP-KB-10Gx120-E 140 70 50 SDP-KB-10Gx140-E 160 90 50 SDP-KB-10Gx160-E 180 110 50 SDP-KB-10Gx180-E 200 130 50 SDP-KB-10Gx200-E 220 150 50 SDP-KB-10Gx220-E Application range ll For embedment of metal components in aerated concrete Characteristics ll H exagon head with flange ll Facade anchor with two-stage screw ll Reliable form-fit in the substrate thanks to combined expansion zones ll High load capacity ll Available with steel screws or stainless steel screws ll Product identification through different sleeve colours Note For planning and processing, please observe approval ETA-12/0502.

www.ejot.com

Article number

EAN

8 532 080 420 8 532 100 420 8 532 120 420 8 532 140 420 8 532 160 420 8 532 180 420 8 532 200 420 8 532 220 420

4061245019307 4061245019277 4061245019246 4061245019222 4061245019208 4061245019185 4061245019161 4061245019147

8 532 080 620 8 532 100 620 8 532 120 620 8 532 140 620 8 532 160 620 8 532 180 620 8 532 200 620 8 532 220 620

4061245019291 4061245019260 4061245019239 4061245019215 4061245019192 4061245019178 4061245019154 4061245019130

Characteristic values Diameter Drive Drill hole depth ≥ t Embedment depth ≥ hv

10 mm A/F13/hexalobular TX40 80 mm 70 mm

Characteristic values Compressive strength of aerated concrete [N/mm2] Aerated concrete 2 0.75 kN Aerated concrete 3 1.31 kN Aerated concrete 4 1.87 kN Aerated concrete 6 3.00 kN Partial safety factor γMAAC 2.00 Characteristic Bending moment Steel screw 17.7 Nm / γMs 1.50 Stainless steel screw 20.6 Nm / γMs 1.87

33


Rear ventilated facades Facade anchors

EJOT® cavity wall repair anchor VSD TX25 SCAN TO SHOP

Length ld mm

Z-21.2-1652

Distance az [mm]

Price/100 Order description [EUR]

Anchor with A4 stainless steel screw (-E) 205 0 - 20 100 225 20 - 40 100 245 40 - 60 100 265 60 - 80 100 285 80 - 100 100 305 100 - 120 100

VSD-8Ux205-E VSD-8Ux225-E VSD-8Ux245-E VSD-8Ux265-E VSD-8Ux285-E VSD-8Ux305-E

Application range ll For fast and adhesive-free subsequent installation of curtain walls ll For load-bearing shells made of concrete, solid brick and perforated brick Characteristics ll Approved anchor for fixing curtain walls ll Double expansion wall anchor: simultaneous embedment in load-bearing wall and outer sheet ll Clean and fast installation (no mortar required) ll Universal expansion zone: secure installation into concrete load-bearing shells, solid and perforated brick ll The use of A4 stainless steel screws guarantees corrosion protection ll 100% installation control ll Temperature-independent installation ll Can be installed at 0°C

Technical specifications Diameter Embedment depth hef Drill hole depth ts Nominal drill diameter Minimum thickness of the outer sheet Drive

Article number

EAN

8 765 205 600 8 765 225 600 8 765 245 600 8 765 265 600 8 765 285 600 8 765 305 600

4061245010670 4061245010663 4061245010656 4061245010649 4061245010632 4061245010625

Note The EJOT® VSD double expansion wall anchor enables the subsequent renovation of doubleleaf masonry. Advanced corrosion or a complete lack of wire anchors can lead to decreased stability of the outer sheet and possibly cause considerable physical injury. In particular curtain walls made before 1979 should be subject to further inspection. When renovating the outer facade, the stability of the curtain wall must be verified. The EJOT® VSD is a particularly cost-effective solution for subsequent installation between load-bearing shell and outer sheet.

8 mm ≥ 70 mm ≥ Id + 10 mm

VSD

8 mm 115 mm Hexalobular TX25 ef

z

a d s

34

www.ejot.com


Rear ventilated facades All wall plug

GRIPPER all wall plug SCAN TO SHOP

L [mm]

d0 [mm]

D [mm]

tsheet, min [mm]

32 38 45

6 8 10

8.5 12 14

8 12 12

Price/100 Order description [EUR] 100 50 50

Application range ll For pre-installation in boards, cavity and solid walls as well as in any other construction material Application examples ll Hand rails ll Wall attachment of cabinets ll Ceiling lights ll Storage racks ll Bookcases ll Mounting televisions ll Heating bodies ll Wash basins ll Urinals ll Electrical installations ll Attachment of HVAC and sanitary equipment ll Attachment of sanitary equipment Base materials Suitable for ll Cinder blocks ll Plasterboard ll High-strength plasterboard ll Hollow expanded clay bricks ll Pre-stressed hollow core slab ll Natural stone ll Non-cracked concrete ll Vertically perforated clay bricks ll Hollow brick sandstone ll Bricks ll Expanded clay aggregate concrete solid brick ll Solid brick sandstone

www.ejot.com

Gripper 6 all wall plug Gripper 8 all wall plug Gripper 10 all wall plug

Article number

EAN

9 650 075 232 9 650 075 234 9 650 075 236

4061245003146 4061245003139 4061245003122

Characteristics ll A nchor made of thermoplastic elastomer The material adapts to the surface of the drill hole, while the non-slip GripEdge surface and the screws ensure secure mechanical embedment ll GRIPPER surpasses normal anchors in its power of resistance against long-term stress, wear, weather conditions, moisture and storage ll Can be used with all popular types and diameters of screws ll The special collar keeps the anchor at the optimal installation depth and also remains covered by the screw head

Appropriate screws GRIPPER 5 GRIPPER 6 GRIPPER 8 GRIPPER 10

ø [mm

Length [mm]

3-4.5 4- 5.5 4.5-6 4.5-7

24 + tfix 32 + tfix 38 + tfix 45 + tfix

35


Rear ventilated facades Nail anchors

Nail anchor ND-K PZ 2 SCAN TO SHOP

L [mm]

d0 [mm]

htot [mm]

Price/100 Order [EUR] description

tfix [mm]

Anchors with zinc-plated steel screw 30 5 40 0-5 40 5 50 10 50 5 60 20 40 6 50 10 60 6 70 30

200 200 200 200 200

Article number

EAN

ND-K 5x 30 V ND-K 5x 40 V ND-K 5x 50 V ND-K 6x 40 V ND-K 6x 60 V

9 650 075 678 9 650 075 680 9 650 075 681 9 650 075 679 9 650 075 682

4061245002880 4061245002866 4061245002859 4061245002873 4061245002842

80

6

90

50

100

ND-K 6x 80 V

9 650 075 683

4061245002835

60 80 100

8 8 8

70 90 110

20 40 60

100 100 100

ND-K 8x 60 V 9 650 075 684 ND-K 8x 80 V 9 650 075 685 ND-K 8x 100 V 9 650 075 686

4061245002828 4061245002811 4061245002804

Anchor with stainless steel screw 30

5

40

0-5

200

ND-K 5/30 E

9 650 075 691

4061245002798

40

6

50

10

200

ND-K 6/40 E

9 650 075 692

4061245002781

80

6

90

50

100

ND-K 6/80 E

9 650 075 693

4061245002774

80

8

90

40

100

ND-K 8/80 E

9 650 075 694

4061245002767

Application range Time-saving simple speed plug for light fastenings: ll Substructures ll Cabinets ll Skirting boards ll Battens ll Cable racks ll Cable clips ll Pipe supports

Characteristics ll Pre-assembled with nail screw, ready-toassemble nylon plugs for drive-in ll Nail screw head with Pozidriv recess for the removal or adjustment of the anchor ll The plug collars serve as plastic insulating washers and thus prevent galvanic corrosion ll Suitable conditions concerning the material quality of the nail screws: GVZ for dry indoor areas

Base materials Suitable for ll Non-cracked concrete ll Bricks ll Natural stone ll Vertically perforated bricks

Characteristic data and loads Type 5x 30 5x 40 5x 50 6x 40 6x 60 6x 80 8x 60 8x 80 8x 100

36

d0 [mm]

df [mm]

hnom [mm]

hef [mm]

AF [mm]

Tinst [Nm]

5 5 5 6 6 6 8 8 8

5.5 5.5 5.5 6.5 6.5 6.5 8.5 8.5 8.5

25 30 30 30 30 30 40 40 40

25 30 30 30 30 30 40 40 40

PZ 2 PZ 2 PZ 2 PZ 2 PZ 2 PZ 2 PZ 2 PZ 2 PZ 2

-

Recommended loads non-cracked concrete C20/25 NRec [kN] 0.2 0.2 0.2 0.4 0.4 0.4 0.6 0.6 0.6

Recommended loads Bricks fb 20.5 N/mm2

VRec [kN] 0.2 0.2 0.2 0.4 0.4 0.4 0.6 0.6 0.6

NRec [kN] 0.1 0.1 0.1 0.2 0.2 0.2 0.3 0.3 0.3

VRec [kN] 0.1 0.1 0.1 0.2 0.2 0.2 0.3 0.3 0.3

www.ejot.com


Rear ventilated facades Nail anchors

EJOT® Nail anchor ND-S PZ 2 SCAN TO SHOP

L [mm]

d0 [mm]

htot [mm]

Price/100 Order [EUR] description

tfix [mm]

Anchors with zinc-plated steel nail 30 5 40 0-5

Article number

EAN

200

ND-S 5x 30 V

9 650 075 658

4061245002965

50

5

60

20

200

ND-S 5x 50 V

9 650 075 659

4061245002958

40 60

6 6

50 70

10 30

200 200

ND-S 6x 40 V ND-S-6x 60 V

9 650 075 660 9 650 075 661

4061245002941 4061245002934

80

6

90

50

100

ND-S-6x 80 V

9 650 075 662

4061245002927

60 80 100

8 8 8

70 90 110

20 40 60

100 100 100

ND-S 8x 60 V 9 650 075 665 ND-S-8x 80 V 9 650 075 663 ND-S 8x 100 V 9 650 075 664

4061245002897 4061245002910 4061245002903

120

5

40

0-5

100

ND-S 8x 120 V 9 650 075 610

4061245003115

140

6

50

10

100

ND-S 8x 140 V 9 650 075 611

4061245003108

160

6

90

50

100

ND-S 8x 160 V 9 650 075 612

4061245003092

Application range Time-saving simple speed plug for light fastenings ll Substructures ll Cabinets ll Skirting boards ll Battens ll Cable racks ll Cable clips ll Pipe supports

Characteristics ll Countersunk head anchors with zinc-plated steel nail ll Pre-assembled with nail screw, ready-toassemble nylon plugs for drive-in ll Nail screw head with Pozidriv recess for the removal or adjustment of the anchor ll The plug collars serve as plastic insulating washers and thus prevent galvanic corrosion ll Suitable conditions concerning the material quality of the nail screws: GVZ for dry indoor areas

Base materials Suitable for ll Non-cracked concrete ll Bricks ll Natural stone ll Vertically perforated bricks

Characteristic data and loads Type 5x 30 5x 50 6x 40 6x 60 6x 80 8x 60 8x 80 8x 100 8x 120 8x 140 8x 160

d0 [mm]

df [mm]

hnom [mm]

hef [mm]

AF [mm]

Tinst [Nm]

5 5 6 6 6 8 8 8 8 8 8

5.5 5.5 6.5 6.5 6.5 8.5 8.5 8.5 8.5 8.5 8.5

25 30 30 30 30 40 40 40 40 40 40

25 30 30 30 30 40 40 40 40 40 40

PZ 2 PZ 2 PZ 2 PZ 2 PZ 2 PZ 2 PZ 2 PZ 2 PZ 2 PZ 2 PZ 2

-

www.ejot.com

Recommended loads non-cracked concrete C20/25 NRec [kN] 0.2 0.2 0.4 0.4 0.4 0.6 0.6 0.6 0.6 0.6 0.6

Recommended loads Bricks fb 20.5 N/mm2

VRec [kN] 0.2 0.2 0.4 0.4 0.4 0.6 0.6 0.6 0.6 0.6 0.6

NRec [kN] 0.1 0.1 0.2 0.2 0.2 0.3 0.3 0.3 0.3 0.3 0.3

VRec [kN] 0.1 0.1 0.2 0.2 0.2 0.3 0.3 0.3 0.3 0.3 0.3

37


Rear ventilated facades Assembly elements for External Thermal Insulation Composite Systems (ETICS)

EJOT® Iso-Dart TX30 SCAN TO SHOP

NEW Price/1 [EUR]

Order description EJOT Iso-Dart 80 EJOT Iso-Dart 100 EJOT Iso-Dart 120 EJOT Iso-Dart 140 EJOT Iso-Dart 160 EJOT Iso-Dart 180 EJOT Iso-Dart 200 EJOT Iso-Dart 220 EJOT Iso-Dart 240 EJOT Iso-Dart 260 EJOT Iso-Dart 280 Application range For retrofitting of light to medium heavy attachments to ETICS facades made of EPS, mineral wool and mineral foam, like for example: ll Downpipe brackets ll Folding shutter latch ll Signs and billboards ll Lamps

Included in delivery 10 EJOT facade anchors (1) 10 installation bushes (2) 10 seals (3) 10 reduction inserts (4) 1 installation bit (5)

Characteristics ll Installation bush made of glass-fibre-reinforced plastic including a high-quality EPDM sealing washer and an EJOT facade anchor (Ø 8 mm) ll Attachments are fastened with common hanger bolts or coarse thread screws ll Common assembly tool ll Recommended service load for each fixing point max. 15 kg

41 mm

1

2

77 mm

4

3 2

5

10 10 10 10 10 10 10 10 10 10 10

Article number

EAN

8 500 080 440 8 500 100 440 8 500 120 440 8 500 140 440 8 500 160 440 8 500 180 440 8 500 200 440 8 500 220 440 8 500 240 440 8 500 260 440 8 500 280 440

4039161012771 4039161012788 4039161012795 4039161012801 4039161012818 4039161012825 4039161012832 4039161012849 4039161012856 4039161012863 4039161013273

Benefits ll High load-bearing capacity through load extension into the substrate ll Reduced thermal transmission by thermal decoupling – Chi value 0.002 W/K according to TR 025 ll Waterproofing against the plaster shell with high-quality EPDM seal - Inspection of the resistance to driving rain in accordance with DIN EN 12155 ll Easy and quick installation

Technical specifications Drill hole diameter 8.0 mm Drill hole depth h1 ≥ in the substrate 80 mm Drive Hexalobular TX30 Processing in installation bush Coarse thread screws Ø 9 mm Hanger bolts Ø 9 mm, M10 Minimum installation depth 40 mm Processing in installation bush + reduction insert Coarse thread screws Ø 5 mm / Ø 6 mm Minimum installation depth 35 mm

4

38

www.ejot.com


Rear ventilated facades Assembly elements for External Thermal Insulation Composite Systems (ETICS)

EJOT® Iso-Dart

Application matrix

1) 2)

Insulation thickness [mm]

Concrete and masonry1)

Solid wood2)

Timber composite plates2) (OSB, wood chipboard d≥18 mm)

80 100 120 140 160 180 200 220 240 260 280 300 320

EJOT Iso-Dart 80 EJOT Iso-Dart 100 EJOT Iso-Dart 120 EJOT Iso-Dart 140 EJOT Iso-Dart 160 EJOT Iso-Dart 180 EJOT Iso-Dart 200 EJOT Iso-Dart 220 EJOT Iso-Dart 240 EJOT Iso-Dart 260 EJOT Iso-Dart 280 -

EJOT Iso-Dart 100 EJOT Iso-Dart 120 EJOT Iso-Dart 140 EJOT Iso-Dart 160 EJOT Iso-Dart 180 EJOT Iso-Dart 200 EJOT Iso-Dart 220 EJOT Iso-Dart 240 EJOT Iso-Dart 260 EJOT Iso-Dart 280 -

EJOT Iso-Dart 80 EJOT Iso-Dart 100 EJOT Iso-Dart 120 EJOT Iso-Dart 140 EJOT Iso-Dart 160 EJOT Iso-Dart 180 EJOT Iso-Dart 200 EJOT Iso-Dart 220 EJOT Iso-Dart 240 EJOT Iso-Dart 260 EJOT Iso-Dart 280

Tolerance compensation up to 30 mm Using the screw without anchor sleeve - only pre-drill up to the substrate

Recommended service loads

Concrete ≥ C12/15 Solid clay brick Solid sand-lime brick

≥ 1.8 ≥ 1.8

Minimum compressive strength fb [N/mm2] 12 12

Solid masonry of lightweight concrete

≥ 0.5

4

0.25

0.15

Vertically perforated clay bricks Perforated sand-lime brick

≥ 0.9 ≥ 1.6

12 12

0.25 0.25

0.15 0.15

Lightweight concrete hollow blocks Aerated concrete

≥ 0.5 ≥ 0.5

2 4

0.15 0.20

0.15 0.15

Chipboard and OSB boards, d ≥ 18 mm

-

-

0.20

0.10

Solid construction timber, d ≥ 60mm

-

-

0.30

0.15

Substrate

Raw density class ? [kg/dm3]

Axial tensile strength 1) [kN]

Shear forcecarrying capacity [kN]

0.30 0.30 0.30

0.15 0.15 0.15

Details apply for the shear force transmission immediately after the bush. When using the reduction insert the axial force is limited to max. 0.2 kN.

1)

www.ejot.com

39


Rear ventilated facades Insulation support anchors

EJOT® insulation support anchor DH (individual components) SCAN TO SHOP

Price/100 Order description [EUR] Washer only 300

EAN

8 550 090 999

4061245011592

Price/100 Order description [EUR]

Article number

EAN

Shaft Shaft Shaft Shaft Shaft Shaft Shaft Shaft Shaft Shaft Shaft Shaft Shaft

8 550 060 999 8 550 080 999 8 550 100 999 8 550 120 999 8 550 140 999 8 550 160 999 8 550 180 999 8 550 200 999 8 550 220 999 8 550 240 999 8 550 260 999 8 550 280 999 8 550 300 999

4061245011622 4061245011608 4061245011578 4061245011554 4061245011530 4061245011516 4061245011493 4061245011479 4061245011455 4061245011431 4061245011417 4061245011394 4061245011370

Washer DH

Insulation thickness ≤ [mm] Shaft only 60 80 100 120 140 160 180 200 220 240 260 280 300

Article number

300 300 300 300 300 300 300 300 300 300 300 300 300

DH 60 DH 80 DH 100 DH 120 DH 140 DH 160 DH 180 DH 200 DH 220 DH 240 DH 260 DH 280 DH 300

Application range ll For fixing insulating material in the rear ventilated facade (VHF) to all substrates

Wall embedment Single-ply insulation

Benefits ll Prevents "quilt effect" (indentations in the insulation) due to retrofitting of the washer ll Prevents gaping of the joints between the individual insulating panels at the joining edges ll Packing and handling volume is reduced by over 60% compared to one-part insulation support anchors ll Installation depth limiter guarantees defined installation, independent of the substrate ll Process reliable installation even with thick insulation boards

Characteristics ll Requirement: 5 pcs. per m2 ll Easy installation with no additional expansion element ll Parts can be positioned freely on the shaft ll All-purpose for all building materials Note For the installation of two-ply insulation, additional stress plates are required. The practicability depends on the respective insulation properties and needs to be tested on site. Rotary hole drilling is obligatory in aerated concrete and perforated brick masonry. Characteristic values Plate diameter Shaft diameter Drill bit diameter Drill hole depth ≥ t Embedment depth ≥ hv

90 mm 8 mm 8 mm 40 mm 30 mm

Point thermal transmittance χ Carrying capacity (pull over washer)

40

0.0001 W/K 0.2 kN

www.ejot.com


Rear ventilated facades Insulation support anchors

EJOT® insulation support anchor DH (set) Values determined by the

SCAN TO SHOP

Insulation thickness ≤ [mm]

Price/100 Order description [EUR]

Set, comprised of washer and shaft 40 300 60 300 80 300 100 300 120 300 140 300 160 300 180 300 200 300 220 300 240 300 260 300 280 300 300 300

DH-40 (one-part) Set DH-60 Set DH-80 Set DH-100 Set DH-120 Set DH-140 Set DH-160 Set DH-180 Set DH-200 Set DH-220 Set DH-240 Set DH-260 Set DH-280 Set DH-300

Application range ll For fixing insulating material in the rear ventilated facade (VHF) to all substrates Benefits ll Prevents "quilt effect" (indentations in the insulation) due to retrofitting of the washer ll Prevents gaping of the joints between the individual insulating panels at the joining edges ll Installation depth limiter guarantees defined installation, independent of the substrate ll Process reliable installation even with thick insulation boards ll Packing and handling volume is reduced by over 60% compared to one-part insulation support anchors

Article number

EAN

8 551 906 009 8 550 060 009 8 550 080 009 8 550 100 009 8 550 120 009 8 550 140 009 8 550 160 009 8 550 180 009 8 550 200 009 8 550 220 009 8 550 240 009 8 550 260 009 8 550 280 009 8 550 300 009

4061245011363 4061245011639 4061245011615 4061245011585 4061245011561 4061245011547 4061245011523 4061245011509 4061245011486 4061245011462 4061245011448 4061245011424 4061245011400 4061245011387

Note For the installation of two-ply insulation, additional stress plates are required. The practicability depends on the respective insulation properties and needs to be tested on site. Rotary hole drilling is obligatory in aerated concrete and perforated brick masonry.

Characteristic values Plate diameter Shaft diameter Drill bit diameter Drill hole depth ≥ t Embedment depth ≥ hv Point thermal transmittance χ Carrying capacity (pull over washer)

Wall embedment Single-ply insulation

90 mm 8 mm 8 mm 40 mm 30 mm 0.0001 W/K 0.2 kN

Characteristics ll Requirement: 5 pcs. per m2 ll Easy installation with no additional expansion element ll Parts can be positioned freely on the shaft ll All-purpose for all building materials

www.ejot.com

41


Rear ventilated facades Insulation support anchors

EJOT® installation point SCAN TO SHOP

Price/100 Order description [EUR] 10

Installation point for DH

Article number

EAN

8 550 000 031

4061245011646

Application range ll Installation tool for ceiling insulation, lintels and split-mould insulation ll Attaches to the DH insulation support anchor

Ceiling embedment Single-ply insulation with installation point

42

Wall embedment Two-ply insulation with installation point

www.ejot.com


Rear ventilated facades Insulation support anchors

EJOT® metal insulation support anchor DMH SCAN TO SHOP

A1

Insulation Anchor length L thickness B ≤ [mm] [mm] Alu-zinc steel 80 110 140 170 200 250 300 A2 stainless steel 80 110 140 170 200 250 300

Price/100 Order description [EUR]

Article number

EAN

40 70 100 130 160 210 260

250 250 250 250 250 200 200

DMH-8x80-V DMH-8x110-V DMH-8x140-V DMH-8x170-V DMH-8x200-V DMH-8x250-V DMH-8x300-V

9 700 030 301 9 700 030 602 9 700 030 603 9 700 030 912 9 700 031 215 9 700 031 520 9 700 031 300

4061245010373 4061245010359 4061245010342 4061245010335 4061245010328 4061245010304 4061245010311

40 70 100 130 160 210 260

250 250 250 250 250 200 200

DMH-8x80-E DMH-8x110-E DMH-8x140-E DMH-8x170-E DMH-8x200-E DMH-8x250-E DMH-8x300-E

9 700 030 302 9 700 033 603 9 700 036 904 9 700 035 912 9 700 035 215 9 700 035 520 9 700 035 300

4061245010366 4061245010298 4061245010243 4061245010250 4061245010281 4061245010267 4061245010274

Application range ll For fixing hard insulation materials ll In combination with the EJOT® DMT metal insulation stress plate also for fixing soft insulation materials ll For fixing insulation materials for high fire protection requirements. Characteristics ll Easy installation by striking in, selfexpanding ll Easy installation ll Fire performance class A1: non-combustible according to DIN EN 13501-1:2010-01 (test certificate no. PZ 3.1/17-226-1) Note The EJOT® insulation support anchors are used to fasten soft and hard insulating material in rear ventilated facades. The insulation board fastening is carried-out according to DIN 18516-1. Rotary hole drilling is obligatory in aerated concrete and perforated brick masonry. For the usage in non-accessible areas of rearventilated facades, we recommend the metal insulation support anchor made of stainless steel.

www.ejot.com

Characteristic values Plate diameter Shaft diameter Drill bit diameter Drill hole depth ≥ t Embedment depth ≥ hv Axial distance a ≥ Edge distance ar ≥ Minimum component thickness hmin Recommended tensile loads Frec Concrete ≥ B25 Solid sand-lime brick Bricks Vertically perforated clay bricks Perforated sand-lime brick Recommended transverse loads Frec Concrete ≥ B25 Solid sand-lime brick Bricks Vertically perforated clay bricks Perforated sand-lime brick

35 mm 8 mm 8 mm 45 mm 40 mm 120 mm 60 mm 80 mm

0.20 kN 0.20 kN 0.20 kN 0.05 kN 0.05 kN 0.25 kN 0.25 kN 0.25 kN 0.10 kN 0.15 kN

43


Rear ventilated facades Insulation support anchors

EJOT® metal insulation stress plate DMT SCAN TO SHOP

Ø [mm] Alu-zinc steel 80 250 A2 stainless steel 80 250

A1

Price/100 Order description [EUR]

Article number

EAN

DMT-80-V

9 700 030 156

4061245010397

DMT-80-E

9 700 030 157

4061245010380

Application range ll For fastening soft insulating materials in combination with the EJOT® DMH metal insulation support anchor ll For fixing soft insulating materials for high fire protection requirements Characteristics ll Fire performance class A1: non-combustible according to DIN EN 13501-1:2010-01 (test certificate no. PZ 3.1/17-226-1)

44

www.ejot.com


Accessories

EJOT® AS spacer SCAN TO SHOP

Thickness [mm] 3 5 8 10 15

Price/100 Order description [EUR]

Article number

EAN

AS-3 AS-5 AS-8 AS-10 AS-15

8 600 725 700 8 601 189 710 8 601 233 720 8 601 232 750 8 601 187 730

4061245020501 4061245020488 4061245020464 4061245020471 4061245020495

100 100 100 100 100

Application range ll To compensate for tolerances on wall and roof

Technical specifications Dimensions

50 x 50 mm

Characteristics ll Plastics ll All-purpose for anchor diameters of 6/8/10 mm ll Easy installation through clipping-on from the side ll Variable combinations

www.ejot.com

45


Notes

46


Contact International

AUSTRIA EJOT Austria GmbH & Co KG Grazer Vorstadt 146 A8570 Voitsberg Phone: +43 3142 2 76 000 Fax: +43 3142 2 76 0030 E-mail: info@ejot.at Internet: www.ejot.at

BALTIC STATES UAB EJOT Baltic Titnago g. 19 LT02300 Vilnius Phone: +370 5 23 11437 Fax: +370 5 23 11439 E-mail: info@ejot.lt Internet: www.ejot.lt

BENELUX EJOT Benelux bvba/sprl Reedonk 19-1 B-2880 Bornem Phone: +32 3 740 79 70 Fax: +32 3 740 79 79 E-mail: info@ejot.be Internet: www.ejot.be

BRAZIL EJOT & Fey Ltda. Rod BR 470, 2451 - Rio Morto Indaial - SC, 89130-000, Brasil Phone: +55 47 3281-7000 E-mail: info@ejot.com.br Internet: www.ejot.com.br

BULGARIA EJOT Bulgaria EOOD & Ko KD Gurmazovsko shose No 96 2227, Bozhurishte Phone: +359 2421 96 37 Fax: +359 2421 96 37 E-mail: mail@ejot.bg

BOSNIA AND HERZEGOVINA EJOT d.o.o. Sarajevo Rajlovacka b.b. BiH-71000 Sarajevo Phone: +387 33 782 760 E-mail: ejot@ejot.ba

CANADA EJOT Construction Fastening Systems Inc. 50 Fleming Drive, Unit 4 Cambridge, ON N1T 2B1 phone: +1 226 499 9977 e-mail: infoca@ejot.com Internet: www.ejot.com

www.ejot.com

CHINA EJOT Fastening System (Taicang) Co., Ltd No.165 Fada Road Loudong Street Taicang, Jiangsu Province P.R. China 215413 Phone: +86 512 53 56 52 90-105 Fax: +86 512 53 56 62 92 E-mail: info@ejot.cn Internet: www.ejot.cn

CROATIA EJOT Spojna Tehnika d.o.o. Franje Lučića 23/3 HR10090 Zagreb Phone: +385 1 349 86 12 Fax: +385 1 349 89 63 E-mail: ejot@ejot.hr CZECH REPUBLIC EJOT CZ, s.r.o. Zdĕbradská 65 CZ25101 ŘičanyJažlovice Phone: +420 323 62 78 11 Fax: +420 323 62 78 20 E-mail: info@ejot.cz Internet: www.ejot.cz

DENMARK EJOT Danmark ApS Industrisvinget 8 DK-4683 Rønnede Phone: +45 56 39 08 42 Fax: +45 56 39 91 06 E-mail: info@ejot.dk Internet: www.ejot.dk

FINLAND Sormat Oy Harjutie 5 FI-21290 Rusko Phone: +358 (0)207 94 0200 Fax: +358 (0)201 76 3888 E-mail: sormat@sormat.com Internet www.sormat.com

FRANCE EJOT France S.à.r.l. Z.I. de Villé - 5 rue du Climont B.P. 40023 F-67220 Villé Phone: +33 388 58 92 00 Fax: +33 388 58 92 01 E-mail: info@ejot.fr Internet: www.ejot.fr

GERMANY EJOT Construction Division In der Stockwiese 35 D57334 Bad Laasphe, Germany Phone: +49 2752 9080 fax: +49 2752 908731 email: bau@ejot.com Internet: www.ejot.de

HUNGARY EJOT Hungaria Kft. Leshegy út 16. H-2310 Szigetszentmiklós Phone: +36 30 546 6807 E-mail: ejot@ejot.hu Internet: www.ejot.hu

ROMANIA EJOT Romania SRL Str. Depozitelor 27 RO-110078 Pitesti Phone: +40 248 223 886 Fax: +40 248 223 887 E-mail: info@ejot.ro

TAIWAN EJOT Taiwan Branch 4No. 8, Aly. 81, Ln. 296, Xinya Rd., Qianzhen Dist. 80673 Kaohsiung, Taiwan, R.O.C. Phone: +886 7 811 08 18 e-mail: ithiel@ejot.com

INDIA EJOT Fastening Systems Pvt. Ltd. A-501/502, Millennium Plaza, Sector-27, Gurgaon -1240022, Haryana, lndia phone: +91 124 4200 492 fax: +91 124 4200 493 e-mail: infoIN@ejot.com

RUSSIA OOO EJOT WOSTOK 105523 Moscow, Russia Schelkovskoe highway, 100 bld. 1 Office 5111 Phone: +7 495 259 09 09 Fax: +7 495 259 09 09 E-mail: info@ejot.ru Internet: www.ejot.ru

TURKEY EJOT Tezmak Cebeci Cad. No. 84 TR34250 KüçükköyIstanbul Phone: +90 212 477 77 92-95 Fax: +90 212 538 00 93 E-mail: info@ejottezmak.com Internet: www.ejottezmak.com

ITALY EJOT S.A.S. di EJOT Tecnologie di fissaggio S.R.L. Via Marco Polo 16 I-35011 Campodarsego (PD) Phone: +39 049 98690 00 E-mail: info@ejot.it Internet: www.ejot.it

JAPAN EJOT Japan L.L.C. 1742-1 Yamada, Kawagoe-Shi, Saitama-Ken, 350-0822 Japan Phone: +81 49 227 9181 Fax: +81 49 227 9112

MEXICO EJOT ATF Fasteners de México y Compañía, S. en C. División Fijaciones para la Construcción Av. Del Siglo No. 180 Parque Industrial Millennium San Luis Potosí S.L.P. C.P. 78395 México Phone: +52 444 8 70 82 25 E-mail: info@ejot-atf.com Internet: www.ejot-atf.com

NORWAY EJOT Festesystem A/S Aslakveien 20A N0701 Oslo Phone: +47 23 25 30 40 Fax: +47 23 25 30 41 E-mail: festesystem@ejot.no Internet: www.ejot.no

POLAND EJOT Polska Spółka z ograniczoną odpowiedzialnością Spółka komandyto Ul. Jeżowska 9 PL42793 Ciasna Phone: +48 34 351 06 60 Fax: +48 34 353 54 10 E-mail: ejot@ejot.pl Internet: www.ejot.pl

SERBIA EJOT Tehnika spajanja d.o.o. Autoput BeogradNovi Sad 296X SCGSerbia, 11080 Zemun Phone: +381 11 748 60 82 Fax: +381 11 748 00 56 E-mail: info@ejot.rs

SLOVAKIA EJOT Slovakia, s.r.o. Juzná trieda 82 (Areál VSS) SK04017 Košice Phone: +421 55 622 17 60 Fax: +421 55 678 09 57 E-mail: info@ejot.sk Internet: www.ejot.sk

SPAIN EJOT Ibérica, S.L.U. C/ Chile, 4 edificio II - oficina 30 E-28290 Las Matas (Las Rozas) Madrid Phone: +34 916 300 822 Fax: +34 911 383 815 E-mail: info@ejot.es Internet: www.ejot.es

SWEDEN EJOT Sverige AB Sandtagsvägen 9 S70236 Örebro Phone: +46 19 20 65 00 Fax: +46 19 20 65 28 E-mail: info@ejot.se Internet: www.ejot.se

SWITZERLAND EJOT Schweiz AG Uttwiler Strasse 3 CH8582 Dozwil Phone: +41 71 414 52 22 Fax: +41 71 414 52 50 E-mail: info@ejot.ch Internet: www.ejot.ch

UNITED ARAB EMIRATES EJOT Middle East FZE Sharjah Airport International Free Zone P.O. Box 120588 Sharjah United Arab Emirates Phone: +971 6 557 97-70 Fax: +971 6 557 97-75 E-mail: info@ejot.ae Internet: www.ejot.com

UNITED KINGDOM EJOT U.K. Ltd. Hurricane Close Sherburn Enterprise Park Sherburn­in­Elmet Leeds, LS25 6PB, GB Phone: +44 1977 68 70 40 Fax: +44 1977 68 70 41 E-mail: info@ejot.co.uk Internet: www.ejot.co.uk

USA EJOT Fastening Systems L.P. 9900 58th Place, Suite 100 Kenosha, Wisconsin 53144 USA Phone: +1 262 612 35 50 Fax: +1 262 721 12 45 E-mail: info@ejot-usa.com Internet: www.ejot-usa.com

www.globalfasteneralliance.com

47


651-EN/-/07.19

EJOT Baubefestigungen GmbH In der Stockwiese 35 D57334 Bad Laasphe, Germany Phone: +49 2752 908-0 Fax: +49 2752 908731 E-Mail: bau@ejot.com Website: www.ejot.com


Turn static files into dynamic content formats.

Create a flipbook