Skip to main content

Practical Low-Power HF Transmitter Design (Extract)

Page 1

Practical Low-Power HF Transmitter Design From Oscillators and Modulation to RF Amplifiers, Filters, and Antennas

Dogan Ibrahim, G7SCU


Practical Low-Power HF Transmitter Design

From Oscillators and Modulation to RF Amplifiers, Filters, and Antennas

● Dogan Ibrahim, G7SCU


● This is an Elektor Publication. Elektor is the media brand of Elektor International Media B.V.

PO Box 11, NL-6114-ZG Susteren, The Netherlands Phone: +31 46 4389444

● All rights reserved. No part of this book may be reproduced in any material form, including photocopying, or

storing in any medium by electronic means and whether or not transiently or incidentally to some other use of this publication, without the written permission of the copyright holder except in accordance with the provisions of the Copyright Designs and Patents Act 1988 or under the terms of a licence issued by the Copyright Licencing Agency Ltd., 90 Tottenham Court Road, London, England W1P 9HE. Applications for the copyright holder's permission to reproduce any part of the publication should be addressed to the publishers.

● Declaration

The author and publisher have used their best efforts in ensuring the correctness of the information contained in this book. They do not assume, or hereby disclaim, any liability to any party for any loss or damage caused by errors or omissions in this book, whether such errors or omissions result from negligence, accident or any other cause.

● British Library Cataloguing in Publication Data

A catalogue record for this book is available from the British Library

● I SBN 978-3-89576-787-6 Print

ISBN 978-3-89576-788-3 eBook ISBN 978-3-89576-789-0 ePub

● © Copyright 2026 Elektor International Media www.elektor.com

Editor: Elektor Team Prepress Production: D-Vision, Julian van den Berg Printers: Ipskamp, Enschede, The Netherlands

Elektor is the world's leading source of essential technical information and electronics products for pro engineers, electronics designers, and the companies seeking to engage them. Each day, our international team develops and delivers high-quality content - via a variety of media channels (including magazines, video, digital media, and social media) in several languages - relating to electronics design and DIY electronics. www.elektormagazine.com

●4


Contents

Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Chapter 1 • Introduction to RF transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.1 What is an RF transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.2 Basic transmitter block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.3 Carrier generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 1.4 Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 1.5 Driver and power amplifier stages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 1.6 Impedance matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 1.7 Feed lines and antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 1.8 Transmitter specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 1.9 Frequency bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 1.10 Legal considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Chapter 2 • RF components and practical construction . . . . . . . . . . . . . . . . . . . . . 23 2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2.2 Resistors at radio frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2.3 Capacitors at radio frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.4 Inductors at radio frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.5 Diodes at radio frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.6 Varactor diodes at radio frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2.7 Bipolar (BJT) RF transistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2.8 JFETs and MOSFETs at RF applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2.9 RF integrated circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.10 Using breadboards in RF applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Chapter 3 • Practical inductor and solenoid coil design . . . . . . . . . . . . . . . . . . . . . 27 3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 3.2 Air-core inductors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 3.2.1 Single-layer coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 3.2.2 Multi-layer coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 3.2.3 Computer program to design single-layer and multi-layer coils . . . . . . . . . . . . . 31 3.2.4 Operation of the program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

●5


Practical Low-Power HF Transmitter Design

3.2.5 RF chokes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 3.2.6 Toroidal inductors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 3.2.7 Ferrite material selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 3.2.8 Tapped coils and link coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 3.2.9 Online coil design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Chapter 4 • Resonance, tuned circuits, and RF filters . . . . . . . . . . . . . . . . . . . . . . . 54 4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 4.2 Inductive and capacitive reactance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 4.3 Series resonance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 4.4 Parallel resonance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 4.5 Loaded and unloaded Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 4.5.1 Q of a tapped coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 4.6 Single-tuned circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 4.7 Double-tuned circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 4.8 Low-pass filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 4.8.1 Butterworth low-pass filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 4.8.2 Computer program to design Butterworth Pi type low-pass filters . . . . . . . . . . . 65 4.8.3 LTspice simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 4.9 High-pass filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 4.9.1 Butterworth high-pass filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 4.9.2 Computer program to design Butterworth Pi type high-pass filters . . . . . . . . . . . 69 4.10 Band-pass filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 4.10.1 Butterworth band-pass filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 4.10.2 Computer program to design Butterworth Pi type band-pass filters . . . . . . . . . 72 4.10.3 LTspice simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Chapter 5 • RF oscillator fundamentals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 5.2 Conditions for oscillation – Barkhausen criterion . . . . . . . . . . . . . . . . . . . . . . . . . 76 5.3 How oscillation starts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 5.4 Amplitude stabilization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 5.5 Frequency stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

●6


Contents

5.6 Transistor biasing for oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 5.7 Oscillator loading, frequency pulling, and buffer stages . . . . . . . . . . . . . . . . . . . . 79 5.8 Oscillator startup problems and troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 80 Chapter 6 • RF LC oscillator circuits and design . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 6.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 6.2 Hartley oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 6.2.1 LTspice simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 6.2.2 Hartley oscillator with a tapped coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 6.3 Colpitts oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 6.3.1 LTspice simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 6.4 Clapp oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 6.5 Output coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Chapter 7 • Crystal ans frequency-controlled oscillators . . . . . . . . . . . . . . . . . . . . 90 7.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 7.2 Crystal equivalent circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 7.3 Crystal data sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 7.4 Crystal pulling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 7.5 Colpitts crystal oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 7.6 Butler oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 7.7 Trimming crystal oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 7.8 Temperature Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 7.9 Crystal Oscillator Buffering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 7.10 Ceramic Resonators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Chapter 8 • Variable frequency oscillators and other signal sources . . . . . . . . . . . 97 8.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 8.2 Variable frequency oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 8.3 Varactor tuned oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 8.4 Direct digital synthesis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 8.4.1 Direct digital synthesis design example . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 8.5 Phase-locked loops (PLL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 8.6 Comparing LC, crystal, PLL, and DDS signal sources . . . . . . . . . . . . . . . . . . . . . 109

●7


Practical Low-Power HF Transmitter Design

8.7 Which source should be used? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Chapter 9 • C ase Study – 7.1505 MHz Pierce oscillator design and construction 111 9.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 9.2 The Pierce oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 9.3 RF Buffer amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 9.3.1 Types of buffer amplifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 9.4 Designing a buffer amplifier for our oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . 117 9.5 Troubleshooting the oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Chapter 10 • Audio generation for modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 10.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 10.2 Electret microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 10.3 Using a LM386 audio amplifier chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 10.4 Troubleshooting the audio circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Chapter 11 • Amplitude modulation techniques . . . . . . . . . . . . . . . . . . . . . . . . . . 129 11.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 11.2 Amplitude modulation (AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 11.2.1 Measuring modulation index on an oscilloscope . . . . . . . . . . . . . . . . . . . . . . 130 11.2.2 Total power in AM signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 11.2.3 Amplitude modulation circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 11.3 Design of an amplitude modulator for our transmitter . . . . . . . . . . . . . . . . . . . 137 Chapter 12 • RF amplifier concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 12.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 12.2 Power output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 12.3 DC input power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 12.4 Power efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 12.5 Power gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 12.6 Voltage gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 12.7 Tuned resonance circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 12.8 Tapped resonance circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 12.8.1 Tapped inductor tuned circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 12.8.2 Single tuned transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

●8


Contents

12.8.3 Tapped capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 12.9 Impedance matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 12.9.1 Matching resistive networks – single frequency match . . . . . . . . . . . . . . . . . 151 12.9.2 Matching complex impedances – single frequency match . . . . . . . . . . . . . . . 154 12.10 RF amplifier configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 12.10.1 Class A RF amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 12.10.2 Class B RF amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 12.10.3 Class AB RF amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 12.10.4 Class C RF amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 12.10.5 Class D RF amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 12.10.6 Class E RF amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 12.10.7 Class F RF amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 12.11 Heatsinks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 12.11.1 MOSFET heatsink calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 12.11.2 BJT heatsink calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Chapter 13 • Designing the RF amplifier stage . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 13. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 13.2 The design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 13.2.1 BJT design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 13.2.2 MOSFET design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 13.2.3 Practical considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 Chapter 14 • Low pass filter and coaxial cable . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 14.2 Practical tuning of the filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 14.3 Coaxial cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 14.4 Estimated transmitter range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 Chapter 15 • Antennas and antenna matching . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 15.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 15.2 Antenna efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 15.3 Antenna input impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 15.4 Standing-wave ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 15.5 Half-wave diploe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191

●9


Practical Low-Power HF Transmitter Design

15.6 Vertical antenna (quarter-wave) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 15.7 Folded dipole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 15.8 Shorter antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 15.9 Loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 15.10 Yagi-Uda antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 15.11 Antenna tuning and impedance matching . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 15.12 Conductor diameter and antenna height . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 15.13 Antenna gain and effective radiated power . . . . . . . . . . . . . . . . . . . . . . . . . . 198 Chapter 16 • Frequency modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 16.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 16.2 Modulation index and sidebands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 16.3 FM bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 16.4 Generating FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 16.4.1 Varactor-diode FM modulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 16.4.2 Voltage controlled oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 16.4.3 Crystal oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 16.4.4 PLL FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 16.4.5 DDS FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 16.5 Converting the AM transmitter to FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 16.5.1 Buffer stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 16.5.2 RF driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 16.5.3 The oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 16.6 Varactor-diode controlled Clapp VFO at 7.1505 MHz . . . . . . . . . . . . . . . . . . . . 202 Chapter 17 • Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 17.1 Breadboard Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 17.2 Keep RF Connections Short . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 17.3 Power-Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 17.4 Power-Supply Decoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 17.5 Design Each Stage Separately . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 17.6 Do Not Ignore Interstage Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 17.7 Use Buffers Where Necessary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210

● 10


Contents

17.8 Calculated Component Values Are Starting Values . . . . . . . . . . . . . . . . . . . . . 211 17.9 Measure Inductors After Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 17.10 Tapped Coils Require Particular Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 17.11 Tune for Power Delivered to the Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 17.12 Avoid Chasing Maximum Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 17.13 Check the Quiescent Operating Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 17.14 Use Adjustable Bias During Development . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 17.15 Thermal Design Must Not Be Neglected . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 17.16 Oscilloscope Probes Affect RF Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 17.17 Simulation and Practical Results Will Differ . . . . . . . . . . . . . . . . . . . . . . . . . . 214 17.18 Use a Dummy Load During Development . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 17.19 Provide Output Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 17.20 Separate RF and Audio Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 17.21 Grounding Is Part of the RF Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 17.22 Shielding May Be Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 17.23 Impedance Matching Should Be Used Where Necessary . . . . . . . . . . . . . . . . . 215 17.24 The Antenna Is Part of the Transmitter System . . . . . . . . . . . . . . . . . . . . . . . 215 17.25 Start at Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 17.26 Observe RF Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 17.27 Educational Design Versus Commercial Design . . . . . . . . . . . . . . . . . . . . . . . 216 17.28 Design at High end HF and VHF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 17.29 Final Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Appendix A • DDS frequency generation program . . . . . . . . . . . . . . . . . . . . . . . . 218 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223

● 11


Practical Low-Power HF Transmitter Design

Preface Radio-frequency transmitter design is an area of electronics in which theory and practical construction are closely linked. A circuit that appears straightforward on paper may behave quite differently when it is constructed, particularly as the operating frequency increases. Component tolerances, stray capacitance and inductance, transistor characteristics, loading between stages, grounding, physical layout, test equipment, and even the oscilloscope probe can noticeably affect the operation of an RF circuit. This book has therefore been written with a strongly practical approach. Its aim is not simply to present equations and standard RF circuits, but to show how a complete transmitter can be developed one stage at a time, beginning with fundamental RF components and resonance and progressing through oscillators, modulation, RF amplification, filtering, transmission lines, impedance matching, and antennas. The emphasis throughout the book is on understanding what each stage does, designing it using relatively simple calculations, simulating the circuit where appropriate, constructing it, measuring its performance, and then modifying the design when practical results differ from theoretical expectations. This process is an important part of RF engineering and is one of the main themes of the book. The early chapters introduce the basic structure of an RF transmitter and describe the principal building blocks from which transmitters are constructed. Particular attention is given to components at radio frequencies because ordinary components do not always behave ideally when used in RF circuits. Resistors possess unwanted inductance and capacitance, capacitors have lead inductance and self-resonant frequencies, and practical inductors contain winding resistance, distributed capacitance, and magnetic losses. These effects become increasingly important as frequency rises. Inductors are particularly important in transmitter circuits, and a complete chapter is therefore devoted to their practical design and construction. Single-layer and multilayer solenoids, RF chokes, ferrite and toroidal inductors, tapped coils, and link coupling are discussed. Computer programs are also included to assist with practical coil design. One lesson that becomes clear during transmitter construction is that calculated inductance should normally be regarded as a starting point. A constructed coil should be measured whenever possible, since its actual inductance can differ from the calculated value. Resonance and tuned circuits form another essential part of RF transmitter design. Series and parallel resonance, loaded and unloaded Q, tapped resonant circuits, and single- and double-tuned circuits are introduced before progressing to RF filters. Butterworth lowpass, high-pass, and band-pass filters are considered in detail. Programs are presented for calculating practical filter component values, and LTspice simulation is used to illustrate circuit behaviour and frequency response.

● 12


Preface

Oscillators form the starting point of the transmitter signal chain. The basic conditions for oscillation, amplitude stabilisation, transistor biasing, frequency stability, and buffering are first introduced. Hartley, Colpitts, Clapp, crystal-controlled, PLL, DDS, and varactorcontrolled oscillators are then examined. The advantages and limitations of the different signal-generation techniques are compared so that the reader can understand why a particular source may be preferred for a particular application. A major practical case study in the book is based on a transmitter operating at approximately 7.1505 MHz. A crystal-controlled oscillator and buffer stage are developed first, followed by an audio section and amplitude modulator. The output is then applied to an RF amplifier stage. This design provides a practical thread through many chapters and demonstrates how the individual subjects discussed earlier in the book are brought together to form a working transmitter. One of the most useful lessons encountered during the development of this transmitter was the importance of interstage loading. A circuit may produce the expected output voltage when tested on its own, but that voltage can fall considerably when the following stage is connected. The input impedance of a driver stage, for example, can load a modulator sufficiently to reduce both the carrier amplitude and the available RF power. Buffer amplifiers are therefore used where necessary, and the book repeatedly emphasises the need to consider each stage not only individually, but also as part of a complete signal chain. RF power amplifiers are treated from both a theoretical and practical viewpoint. Power output, DC input power, efficiency, voltage gain, power gain, biasing, tuned loads, tapped resonant circuits, and impedance transformation are introduced before Class A, B, AB, C, D, E, and F operation is described. Both BJT and MOSFET amplifier designs are considered. Thermal design and heatsink calculations are also included because device dissipation can become an important practical limitation even at modest transmitter power levels. Impedance matching receives considerable attention throughout the book. At RF, maximum voltage is not necessarily the objective. What is normally more important is the useful power delivered to the next stage or to the load. Matching using tapped coils, transformers, L networks, T networks, and Pi networks is therefore described. Complex impedances are also considered, and computer programs are included to assist with calculations that would otherwise be tedious to perform manually. The transmitter output does not end at the RF amplifier. Harmonic filtering, coaxial cable, antenna impedance, standing-wave ratio, antenna matching, and radiation efficiency all form part of the complete transmitter system. Several commonly used antennas are introduced, including half-wave dipoles, quarter-wave verticals, folded dipoles, loops, shortened antennas, and Yagi-Uda arrays. The effect of antenna height, conductor diameter, gain, and matching is also discussed. Although the main practical transmitter is initially developed for amplitude modulation, the final part of the book shows how many of the same transmitter stages can be retained when frequency modulation is used. FM generation using varactor diodes, voltage-controlled

● 13


Practical Low-Power HF Transmitter Design

oscillators, crystal oscillators, PLL systems, and DDS techniques is introduced. A varactorcontrolled Clapp oscillator operating near the same transmitter frequency provides a practical FM example. This demonstrates an important design principle: the oscillator and modulation method may change while much of the following RF amplification, filtering, matching, and antenna system can remain substantially unchanged. LTspice simulation is used throughout the book where it helps to explain circuit operation or verify a design before construction. Simulation is extremely useful, but it should not be regarded as a substitute for practical measurement. Real transistors differ from idealised models, constructed inductors have losses and stray capacitance, wiring introduces unwanted reactance, and instruments themselves affect RF circuits. For this reason, comparisons between calculated, simulated, and measured results are an important part of the practical examples. Several computer programs are also included. These programs are intended to remove repetitive calculations while at the same time reinforcing the underlying theory. Examples include coil design, tuning-capacitor calculations, Butterworth filter design, and complex impedance matching. The programs can be studied as part of the design process or used directly as practical engineering tools. The final chapter brings together many of the practical lessons encountered during the development of the circuits in the book. These include keeping RF connections short, providing adequate power-supply decoupling, designing and testing one stage at a time, measuring constructed inductors, allowing for loading, using buffers where necessary, checking quiescent operating conditions, providing adequate thermal design, using dummy loads during development, filtering the transmitter output, and treating grounding and physical construction as part of the RF design itself. Perhaps the most important point is that calculated component values should rarely be regarded as final values in an RF circuit. They provide a technically sound starting point, but practical adjustment is often required. Similarly, pursuing the greatest possible output voltage or power is not always desirable. A clean waveform, stable operation, acceptable device temperature, correct impedance matching, and adequate harmonic suppression are generally more important than extracting the final few milliwatts from a circuit. The circuits and methods described in this book are primarily intended for education, experimentation, and understanding RF transmitter principles. Readers should begin at low power, use dummy loads during development, and observe the radio regulations and licensing requirements applicable in their own countries before connecting a transmitter to an antenna. It is hoped that the approach used in this book will help readers move beyond viewing an RF transmitter as a collection of isolated circuits. The oscillator, buffer, modulator, driver, power amplifier, matching network, filter, feed line, and antenna all interact and must ultimately be considered as parts of one complete RF system. By combining theory, calculation, simulation, computer-assisted design, construction, and measurement, the

● 14


Preface

reader should gain both an understanding of RF transmitter principles and the confidence to develop and investigate transmitter circuits independently. Dogan Ibrahim, G7SCU

● 15


Practical Low-Power HF Transmitter Design

Chapter 1 • Introduction to RF transmitters 1.1 What is an RF transmitter An RF transmitter is an electronic system that generates a radio-frequency signal and delivers it to an antenna so that information can be transmitted through space. The information being transmitted may take many forms, including: • speech, • music, • digital data, • sensor information, • control commands, • television pictures, • navigation information, • or telemetry data. The information signal itself is normally unsuitable for efficient transmission over large distances. For example, an audio signal may occupy frequencies from a few tens of hertz to several kilohertz. Directly radiating such a low-frequency signal would require an impractically large antenna. Instead, the information is combined with a much higherfrequency signal known as the carrier. The carrier can then be modified, or modulated, according to the information signal. The modulated RF signal is amplified and applied to an antenna. A transmitter therefore performs several fundamental operations: 1. 2. 3. 4. 5. 6.

Generate a stable RF carrier. Apply the information signal to the carrier by modulation. Increase the RF signal power. Remove unwanted frequencies and harmonics. Match the transmitter to the feed line and antenna. Radiate the signal efficiently.

A simple transmitter may contain only a few transistors. In contrast, a modern communication transmitter may include frequency synthesizers, mixers, digital signal processors, automatic power-control circuits, microcontrollers, and several RF amplifier stages. Despite these differences, the basic operating principles are largely the same.

1.2 Basic transmitter block diagram A general purpose RF transmitter can be represented by the block diagram shown in Figure 1.1. The exact arrangement depends on the type of transmitter. Some blocks may be combined, while additional stages may be inserted. For example, a very simple low-power transmitter might only consists of: Oscillator → Modulator → RF Amplifier → Antenna

● 16


Chapter 1 • Introduction to RF transmitters

A higher performance transmitter may include parts such as frequency synthesizer, buffer, driver, low-pass filter, matching network and so on.

Figure 1.1 Basic transmitter block diagram

1.3 Carrier generation At the heart of practically every transmitter is an RF oscillator. An oscillator generates a periodic electrical signal without requiring a periodic input signal. In a transmitter, it normally generates the RF carrier signal, where for example in an FM transmitter the carrier frequency can be 100 MHz or more, or less. The quality of the carrier generator has a major influence on transmitter performance. Some important oscillator characteristics are: • Frequency accuracy, the more accurate the better • Frequency stability, the more stable the better • Output amplitude, reasonable clean output required • Harmonic content, the less the better • Temperature stability, no change with temperature Several types of oscillators are used as carriers in transmitters. LC oscillators are particularly useful at radio frequencies. Some examples are: Colpitts oscillator, Hartley oscillator, Clapp oscillator etc. Crystal oscillators are also commonly used to provide considerably better frequency stability. Modern transmitters use frequency synthesizers in the form of phaselocked loops (PLL) rather than free-running oscillators in order to provide stability and frequency ranges from a few megahertz to several gigahertz.

1.4 Modulation A pure RF carrier contains no information. To transmit information, one or more characteristics of the carrier must be varied according to the information signal. This process is called modulation. Basically, three fundamental properties of a sinusoidal carrier can be modified: amplitude (e.g. amplitude modulation) , frequency (e.g. frequency modulation), and phase (e.g. phase modulation). Modulation can be analog or digital. In this book we are only interested in analog modulation. If the carrier amplitude is varied, the process is amplitude modulation (AM). If the frequency is varied, the process is frequency modulation (FM), and if the carrier phase id varied, the process is phase modulation (PM).

● 17


Practical Low-Power HF Transmitter Design

Digital transmitters use different modulation techniques, such as: amplitude-shift keying (ASK), frequency-shift keying (FSK), phase-shift keying (PSK), quadrature amplitude modulation (QAM) etc. In summary, the output of the modulator is an RF signal containing the information to be transmitted.

1.5 Driver and power amplifier stages The modulated signal leaving the oscillator or modulator usually has relatively little power. It must therefore be amplified before it can drive the final RF power amplifier and then the antenna. The first amplification stage is often called a buffer amplifier. A buffer amplifier performs an especially important function: it isolates the oscillator from later transmitter stages so that the modulator stage is not loaded. Without sufficient isolation, variations in the power amplifier or antenna load can be reflected back toward the oscillator and cause its frequency to change. This unwanted effect is sometimes called frequency pulling. The buffer therefore helps maintain carrier frequency stability. Following the buffer, one or more driver amplifiers may be used depending on the power amplifier requirements. The purpose of the driver is to raise the RF power to a level sufficient to operate the final power amplifier. For example, a final RF amplifier producing several watts may require tens or hundreds of milliwatts of drive power. The RF power amplifier (PA), is the stage that increases the RF signal to the power level required for transmission. The modulator may produce only a few milliwatts of RF power, whereas the required transmitter output could range from milliwatts to many kilowatts depending upon the application. Low-power transmitters might have a few milliwatt of power for short range. Professional communications might have tens or hundreds of watts of power. Broadcast transmitters can have kilowatts of power. Some important requirements of power amplifiers are: power gain, efficiency, linearity, harmonic content, operating frequency, and thermal performance. For example, Class A amplifiers have excellent linearities but relatively poor efficiencies. Class C amplifiers can provide much higher efficiency but poor linearity. A practical RF power amplifier does not produce perfect output signal because of the non-linearity of transistor circuits. It is important that the harmonic content of the power amplifier should be minimized. For example, a 10 MHz transmitter may produce harmonics at 20 MHz (2nd harmonic), 30 MHz (3rd harmonic), 40 MHz (4th harmonic) and at higher frequencies. These harmonics must be filtered so that they do not reach the antenna.

1.6 Impedance matching Maximum RF power is transferred when the transmitter output impedance is correctly matched to the load (i.e. the antenna). Most RF transmission systems use the standard impedance of 50 Ohms. The output impedance of an RF power transistor is not necessarily 50 ohms and it may instead have an optimum load impedance of only a few ohms or perhaps several hundred ohms. An impedance matching network is a circuit that transforms

● 18


this impedance to the standard impedance required by the feed line and antenna system. Incorrect matching can results in: • Reduced output power • Distortion • Increased power dissipation • Excessive transistor heating • High reflected power • Possible damage to power transistors Impedance matching circuits commonly use inductors and capacitors. Some common configurations are: L networks, Pi networks, T networks, transformer matching etc.

1.7 Feed lines and antenna The feed line carries RF energy from the transmitter to the antenna. For low-frequency circuits, an ordinary wire might appear adequate. At radio frequencies, however, the connection between the transmitter and antenna behaves as a transmission line and must be treated accordingly. A common feed line is coaxial cable which has a characteristic impedance of either 50 Ohms or 75 Ohms, although most transmitter system use 50 Ohms. At very high frequencies, striplines, microstrips, or waveguides can be used. The antenna converts the electrical RF signal supplied by the transmitter into electromagnetic waves that travel through space. It therefore forms the interface between the electronic transmitter and the propagation medium. The physical dimensions of an antenna are usually related to the wavelength of the transmitted signal. The antenna influences the transmitter range, radiation pattern, and the efficiency of the transmitter considerably. There are many different types of antenna, including: • Diploe antenna • Loop antenna • Monopole antenna • Yagi antenna • Patch antenna • Horn antenna • Vertical antenna • Parabolic antenna • Etc The transmitted electromagnetic wave consists of electric and magnetic fields that propagate away from the antenna at approximately the speed of light. The wave may travel to the receiver by several different propagation mechanisms depending upon frequency and distance, including: direct (line-of-sight) propagation, ground-wave propagation, reflection, scattering, sky-wave propagation, etc. The strength of the received signal depends on the transmitter power, receiver antenna gain, transmitter to receiver distance, operating frequency, terrain, environmental factors, obstacles, and receiver antenna characteristics.

● 19


Practical Low-Power HF Transmitter Design

1.8 Transmitter specifications RF transmitters are normally described by a number of electrical and performance specifications. These specifications indicate how much power the transmitter produces, how accurately it operates at the required frequency, how efficiently it converts DC power into RF power, and how clean the transmitted signal is. Understanding these specifications is important when designing, testing, or comparing transmitters. Some important specifications are: Output power: Indicates how much RF power is delivered to the load, usually a 50 Ohm antenna. The power is expressed as Watts or dBm. Operating frequency: This specifies the carrier frequency or range of frequencies over which the transmitter is designed to operate. Frequency accuracy: Indicates how closely the actual transmitted frequency corresponds to the required frequency. Usually expressed in parts per million. For example, an oscillator operating at 100 MHz with an accuracy of 10 ppm can have a maximum frequency error of 1 kHz. Frequency stability: Describes how much the transmitter frequency changes with time, supply voltage, or temperature. Bandwidth: This is the range of frequencies that can be handled by the transmitter. Efficiency: This indicates how effectively the transmitter converts DC power into RF output power. It is measured in percentage. Harmonic output: This specifies the harmonic output relative to the carrier, usually in sBc, i.e. dB below the carrier signal. Modulation depth and deviation: These determine how accurately the information is carried by the RF signal. VSWR: This is a measure of the quality of impedance match between the transmitter, feed line, and the antenna, commonly expressed as Voltage Standing Wave ratio. In a perfect match, VCWR = 1:1. Operating voltage: This is also important. High power transmitters operate with mains voltage, while low power ones may operate even with batteries. Current consumption: It is important to make sure that the required current can be supplied by the power supply.

● 20


Chapter 1 • Introduction to RF transmitters

1.9 Frequency bands The radio-frequency spectrum covers an enormous range of frequencies. For convenience, it is divided into a number of internationally recognised bands. The principal frequency bands are shown below. Band

Frequency Range

Typical Applications

VLF

3–30 kHz

Navigation, time signals, submarine communication

LF

30–300 kHz

Navigation, long-wave broadcasting

MF

300 kHz–3 MHz

AM broadcasting, maritime communication

HF

3–30 MHz

Short-wave radio, amateur radio, long-distance communication

VHF

30–300 MHz

FM radio, television, aviation, marine radio

UHF

300 MHz–3 GHz

Television, mobile radio, GPS, Wi-Fi, Bluetooth

SHF

3–30 GHz

Radar, satellite links

EHF

30–300 GHz

Millimetre-wave communication, radar

HF signals can travel very long distances because they may be refracted or reflected by regions of the ionosphere. HF is therefore widely used for: amateur radio, international broadcasting, maritime communication, military communication. VHF applications include: FM broadcasting, aircraft communication, marine radio, some television services. UHF applications include: Bluetooth, Wi-Fi, GPS, mobile communications, television broadcasting Microwave frequencies include applications: microstrip transmission lines, distributed matching networks, stripline, RF connectors.

1.10 Legal considerations Radio transmitters cannot normally be operated at arbitrary frequencies and power levels. The radio spectrum is a shared and limited resource used by many essential services, including aviation, emergency services, broadcasting, navigation, military systems, amateur radio etc. Uncontrolled transmissions could interfere with these services. For this reason, the use of radio transmitters is regulated in most countries. The exact rules differ between countries, so anyone constructing or operating a transmitter must consult the regulations applying in the country in which the equipment is to be used. Some low-power radio services

● 21


Practical Low-Power HF Transmitter Design

may be operated without radio license provided they comply with specified requirements. Regulations usually limit the maximum permitted transmitted power, maximum antenna gain, occupied bandwidth, harmonics, modulation type etc. Some license-exempt services are: • Wireless sensors • Alarm systems • Remote controls • Wi-Fi equipment • Bluetooth equipment • Short-range transmitters Licensed radio amateurs are permitted to construct and experiment with their own transmitters within designated amateur frequency bands. This makes amateur radio particularly important for practical RF experimentation. However, an amateur radio licence does not provide unrestricted access to the spectrum. Operators must comply with requirements relating to permitted frequencies, maximum power, operating procedures, identification, interference, etc. An experimental RF circuit should not normally be connected directly to an antenna merely to determine whether it works. A much safer approach is to test the transmitter using a dummy load. A dummy load is a non-radiating load, normally designed to present an impedance of 50 Ohms to the transmitter. The output can then be observed on an oscilloscope, an RF power meter, a frequency counter, or a spectrum analyzer. A useful principle is: Do not connect an experimental transmitter to an antenna until you know its frequency, output power, bandwidth, and unwanted-emission levels are suitable for legal transmission. The transmitter circuits described in later chapters should therefore initially be regarded as laboratory circuits. Where appropriate, they should first be constructed and tested into a suitable 50 Ohms dummy load. Any connection to an antenna should comply with the frequency, power, licensing, and equipment regulations applicable in the country where the transmitter is operated.

● 22


Index

Index A AD9850 Adjustable bias Air-core inductor Amplitude modulation Amplitude stabilization Antenna Antenna efficiency Antenna gain Antenna input impedance Antenna matching Antenna tuning Audio amplifier Audio generation Audio quality AWG

101 213 27 129 77 189 190 198 190 189 197 121 121 132 29

B Balanced modulator Bandwidth Band-pass filter Barkhausen criterion BB809 Bipolar transistors at RF BJT heatsink BNC Breadboard BS170 Buffer stage Butler oscillator Butterworth low-pass filter

134 20 71 76 99 25 163 187 26, 208 117 79 95 63

C Capacitors at RF Capacitive reactance Carrier Ceramic resonator Clapp oscillator Class A amplifier Class AB amplifier Class B amplifier Class C amplifier Class D amplifier Class E amplifier

24 54 15 96 87 158, 171 159 159 160 160 160

Class F amplifier Coaxial cable Coil design Collector modulator Colpitts crystal oscillator Colpitts oscillator Conductor diameter Copper wire diameters Crystal equivalent circuit Crystal oscillator Crystal pulling

160 182, 186 31 136 93 85 197 29 90 90 93

D DC input power DDS DDS FM Diodes at RF Direct digital synthesis Double-tuned circuit Driver Drive level Dummy load

143 100 201 24 100 63 18 92 214

E Effective radiated power Efficiency Electret microphone Emitter coupled pair Emitter bypass capacitor Emitter follower Emitter modulator ESR

198 20 121 134 173 116 136 92

F Feed line Ferrite material Filter program Fixed capacitor Fixed inductance FM bandwidth FM modulator Folded dipole Frequency accuracy Frequency bands

19 46 65, 69, 72 98 97 200 200 193 20 21

● 223


Practical Low-Power HF Transmitter Design

Frequency controlled oscillator Frequency deviation Frequency modulation Frequency pulling Frequency stability G Grounding

90 199 199 79 17, 20, 77

215

H Half-wave dipole Harmonics Hartley oscillator Heatsink High-pass filter

191 78, 182 81 160 68

I Impedance matching Impedance matching program Inductive reactance Inductors at RF Interstage loading

18, 151 154 54 24 210

J JFET at RF

25

K KV1471

204

L LC oscillator Legal considerations LM386 Load capacitance Loaded Q Loop antenna Low-pass filter

81 21 126 92 59 194 182

M Modulation Modulation index MOSFET at RF MOSFET heatsink MOSFET modulator Multi-layer coil Multiplier chip

17 130, 199 25 161 137 28 134

● 224

Mutual inductance

50

N Network analyzer Noise

196 132

O OLED Output amplitude Oscillator frequency Oscillator loading Oscillator startup Oscilloscope probes Output coupling Output filtering Output power Overtone crystal

101 17 20, 79 79 80 213 89 214 20 95

P Parallel resonance Parasitic element Phase locked loop Phase noise Pierce oscillator PLL PLL FM Power amplifier Power efficiency Power gain Power output Practical tuning

56 194 108 78 111 108 201 18 144 144 143 185

Q Quality factor

54

R Resistors at RF Resonance Reverse bias RF amplifier RF buffer amplifier RF choke RF filter RF input coupling RF oscillator Ring modulator

23 54 98 143 115 35 54 173 17, 75 135


Index

Rotary encoder

101

S Series resonance Shielding Shorter antenna Side bands Single-layer coil Single-tuned circuit Single-tuned transformer Source follower Spurious oscillation Square law modulator Standing-wave ratio Supply decoupling SWG

55 215 193 199 27 62 150 116 78 132 190 173, 209 29

T Tapped capacitor Tapped coil Tapped inductor Tapped resonance circuit Temperature stability Thermal design Toroidal inductors Total power Transistor biasing Transmitter range Trimming Tuned circuit

150 47, 60 149 148 96 213 46 131 78 187 95 54

U Unloaded Q

59

V Varactor diodes at RF Varactor oscillator Variable frequency oscillator Vertical antenna Voltage gain VSWR

25 98 97 192 144 20

W Wheeler formula

27

Y Yagi-Uda antenna

194

● 225


Practical Low-Power HF Transmitter Design

Practical Low-Power HF Transmitter Design From Oscillators and Modulation to RF Amplifiers, Filters, and Antennas Discover the principles, techniques, and practical skills behind radiofrequency (RF) transmitters in this comprehensive guide to designing, building, simulating, testing, and troubleshooting real RF circuits. Starting with the fundamentals of oscillation and resonance, this book takes you step by step through the complete transmitter chain, from signal generation to antenna. Explore Hartley, Colpitts, Clapp, Pierce, crystalcontrolled, varactor, PLL, and DDS oscillators, alongside practical methods for generating amplitude modulation (AM) and frequency modulation (FM). Learn how to design oscillators, buffer stages, RF drivers, and power amplifiers, and understand the operating principles of Class A, B, AB, C, D, E, and F amplifiers. Discover how component selection, biasing, tuned loads, efficiency, and thermal management influence real-world performance. Practical circuit design is at the heart of this book. You will learn to calculate inductors, work with resonant circuits, match complex impedances using L, T, and Pi networks, and design Butterworth filters with support from LTspice simulations. Useful computer programs simplify calculations for coils, tuning capacitors, filters, and impedance-matching networks. A detailed 7.1505 MHz transmitter case study brings these concepts together, demonstrating how individual stages can be designed, tested, and integrated into a working system.

Prof. Dr. Dogan Ibrahim has a BSc degree in Electronic Engineering, an MSc degree in Automatic Control Engineering, and a PhD degree in Digital Signal Processing. He worked for several industrial organizations before he returned to academic life. Prof. Ibrahim is the author of over 120 technical books and published over 200 technical articles on microcontrollers, microprocessors, and related fields. He is a chartered electrical engineer and a Fellow of the Institution of Engineering and Technology. He is a certified Arduino professional.

Beyond theory, this book addresses the challenges that often determine success in practice: parasitic effects, grounding, shielding, decoupling, circuit loading, component tolerances, and thermal behavior. Whether you are an engineer, a radio amateur, or a student, this book will help you move beyond formulas and develop a deeper understanding of how RF transmitters really work.

● 226

More info: www.elektor.com/21365

Elektor International Media www.elektor.com


Turn static files into dynamic content formats.

Create a flipbook
Practical Low-Power HF Transmitter Design (Extract) by Elektor - Issuu