Skip to main content

Caterpillar Cat 12M Motor Grader (Prefix B9F) Service Repair Manual Instant Download

Page 1

Service Repair Manual

Models

12M Motor Grader


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4...

1/45

Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 12M MOTOR GRADER B9F Configuration: 12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine

Disassembly and Assembly 12M and 120M Motor Graders Power Train Media Number -KENR6419-08

Publication Date -01/05/2017

Date Updated -15/05/2017

i07077362

Transmission - Disassemble SMCS - 3030-015; 3159-015; 3176-015

Disassembly Procedure Table 1 Required Tools Tool

Part Number

Part Description

Qty

A

439-3940

Link Bracket

3

B

422-8733

Jack Stand Gp

3

C

1U-9202

Lever Puller Hoist

1

D

1P-1863

Retaining Ring Pliers

1

E

308-3470

Jack Stand Gp

2

F

140-7742

Sleeve

1

G

154-6181

Forcing Bolt

2

H

FT-2769

Table

1

J

4C-8156

Lifting Fixture

1

1U-6410

Three Jaw Puller

1

1P-0510

Driver Gp

1

9U-7480

Compressing Tube

1

5P-7970

Nut

1

8T-4224

Hard Washer

1

K L

-

1

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4...

Bolt M8 - 1.25 by 460mm M

8B-7548

Push-Puller Tool Gp

1

N

2P-8312

Retaining Ring Pliers

1

1P-2321

Combination Puller

1

1P-0510

Driver Gp

1

189-0408

Shackle As

1

3E-3882

Eyebolt

1

126-7175

Push-Puller Tool Gp

1

4C-5653

Threaded Adapter

1

1P-0510

Driver Gp

1

P

R

S

Start By: a. Remove the transmission.

NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates.

NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life.

Note: Put identification marks on all harness assemblies for installation purposes.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11

2/45


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4...

Illustration 1

3/45

g01386565

1. Attach Tooling (A) and a suitable lifting device to transmission (1). The weight of transmission (1) is approximately 862 kg (1900 lb). Use Tooling (A) and the suitable lifting device to position transmission (1) onto Tooling (B). Remove hose assembly (2).

Illustration 2

g01386568

2. Remove bolts (3) to remove control module (4) and spacers (5).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4...

Illustration 3

4/45

g01386574

3. Remove yoke assembly (6).

Illustration 4

g01386575

4. Remove retaining ring (7). 5. Remove cup (8). Remove O-ring seal (9).

Illustration 5

g01386579

6. Attach Tooling (A), Tooling (C), and a suitable lifting device to transmission (1). Use Tooling (A), Tooling (C), and the suitable lifting device to position transmission (1) onto Tooling (B) and suitable cribbing. Position transmission (1) with the output shaft upward.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4...

Illustration 6

g01386585

Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.

7. Remove bolts (10) to remove plate assembly (11).

Illustration 7

g01386589

8. Remove lip seal (12).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11

5/45


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4...

Illustration 8

g01386599

9. Use Tooling (D) to remove retaining ring (13). Remove coned disc springs (14). Note: Note the orientation of coned disc springs (14) for assembly purposes.

Illustration 9

g01386610

10. Remove O-ring seal (15) and piston (16).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11

6/45


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4...

Illustration 10

7/45

g01386621

11. Remove piston seal (17). Remove piston seal (18).

Illustration 11

g01386624

12. Disconnect harness assembly (19) and harness assembly (21). Remove guard (20).

Illustration 12

g01386632

13. Remove bolts (22). Use two people to remove housing (23). The weight of housing (23) is approximately 20 kg (45 lb).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4...

Illustration 13

g01386646

14. Remove pressure sensor (24) and the O-ring seal. Remove solenoid (25).

Illustration 14

g01386658

15. Remove O-ring seal (26), O-ring seal (27), O-ring seal (28), O-ring seal (29), and O-ring seal (30).

Illustration 15

g01386662

16. Remove seal (31).

Illustration 16

g01386663

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11

8/45


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4...

9/45

17. Remove friction discs (32) and clutch plates (33). Note: Note the quantity and the order of friction discs (32) and clutch plates (33) for assembly purposes. 18. Remove O-ring seals (34) and dowels (35).

Illustration 17

g01386675

19. Remove retaining ring (36). Remove hub (37).

Illustration 18

g01386684

20. Attach Tooling (A), Tooling (C), Tooling F, and a suitable lifting device to transmission (1). Use Tooling (A), Tooling (C), Tooling (F), and the suitable lifting device to position transmission (1) onto Tooling (B) and Tooling (E) with the output shaft downward. The weight of transmission (1) is approximately 862 kg (1900 lb).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 19

g01386730

21. Remove bolt (38) to remove speed sensor (39) and guard (40).

Illustration 20

g01386747

22. Remove bolts (41) to remove speed sensor (42) and speed sensor (43).

Illustration 21

g01386749

23. Remove cover (44).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11

10/45


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 22

11/45

g01386757

24. Remove bolts (45) to remove speed sensor (46) and speed sensor (47).

Illustration 23

g01386764

25. Attach Tooling (A), Tooling (C), and a suitable lifting device to housing (49). The weight of housing (49) is approximately 136 kg (300 lb). Remove bolts (48). 26. Use Tooling (A), Tooling (C), and the suitable lifting device to remove housing (49). Note: If necessary, use Tooling (G) to assist in removal of housing (49).

Illustration 24

g01386792

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

12/45

27. Remove O-ring seal (50). Remove bolts (51) and the locks. Remove tube assembly (52) and the O-ring seal.

Illustration 25

g01386795

28. Remove bolts (53) to remove seal carrier (54). Remove bolts (55) to remove seal carrier (56).

Illustration 26

g01386797

29. Remove seal rings (57). Remove O-ring seals (58). Repeat this step for the remaining seal carrier.

Illustration 27

g01386811

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 28

13/45

g01386815

30. Use Tooling (J) and a suitable lifting device to remove clutch assembly (59) and clutch assembly (60). The combined weight of clutch assembly (59) and clutch assembly (60) is approximately 163 kg (360 lb). 31. Position clutch assembly (59) and clutch assembly (60) onto Tooling (H). If necessary, support clutch assembly (60) with suitable cribbing. 32. Remove Tooling (J) to separate clutch assembly (59) from clutch assembly (60).

Illustration 29

g01386827

33. Use Tooling (K) to remove bearing (61) and rotor (62) from clutch assembly (59). Note: Be sure to attach Tooling (K) to gear assembly (63) to prevent damage to rotor (62).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 30

g01386841

34. Remove thrust washer (64) and gear assembly (63). Note: Note the orientation of thrust washer (64) for assembly purposes.

Illustration 31

g01386992

35. Remove bearing sleeves (65) from gear assembly (63).

Illustration 32

g01386993

36. Remove thrust washer (66).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11

14/45


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

15/45

Note: Note the orientation of thrust washer (66) for assembly purposes.

Illustration 33

g01386997

Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.

37. Use Tooling (L) to compress hub assembly (67). Remove lock rings (68) and two half rings (69) (not shown). Note: Note the orientation of lock rings (68) and two ring halves (69) for assembly purposes.

Illustration 34

g01387088

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

38. Remove hub assembly (67), friction discs (70), and clutch plates (71). Note: Note the order of friction discs (70) and clutch plates (71) for assembly purposes.

Illustration 35

g01387093

39. Remove wave spring (72) and piston (73).

Illustration 36

g01387119

40. Remove seal rings (74) and (75) from piston (73).

Illustration 37

g01387137

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11

16/45


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

17/45

41. Use a suitable lifting device to turn over clutch assembly (59). The weight of clutch assembly (59) is approximately 59 kg (130 lb).

Illustration 38

g01387150

Illustration 39

g01387221

Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.

42. Use Tooling (M) to remove bearing (76). Remove thrust washer (77), thrust disc (78), and gear assembly (79). Note: Note the orientation of thrust disc (78) for assembly purposes.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 40

g01387228

43. Remove thrust disc (80), washer (81), half rings (82), and lock rings (83). Note: Note the orientation of thrust disc (80) for assembly purposes.

Illustration 41

g01387232

44. Remove hub assembly (84). Remove friction discs (85) and clutch plates (86). Note: Note the orientation of friction discs (85) and clutch plates (86) for assembly purposes.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11

18/45


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 42

19/45

g01387235

45. Use Tooling (N) to remove retaining ring (87). 46. Remove balance piston (88). Remove seal ring (89) from balance piston (88). 47. Remove springs (90). 48. Remove piston (91). Remove seal rings (92) and (93) from piston (91).

Illustration 43

g01387511

49. Use Tooling (K) to remove inner bearing (94) from clutch assembly (60). Remove thrust disc (95) and gear (96). Note: Note the orientation of thrust disc (95) for assembly purposes.

Illustration 44

g01387520

50. Remove thrust disc (97) and gear assembly (98) from clutch assembly (60). Note: Note the orientation of thrust disc (97) for assembly purposes.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 45

g01387526

51. Remove sleeve bearing (99) from gear assembly (98).

Illustration 46

g01387528

52. Remove thrust disc (100) and washer (101) from clutch assembly (60). Note: Note the orientation of thrust disc (100) for assembly purposes.

Illustration 47

g01387541

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11

20/45


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

21/45

Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.

53. Use Tooling (L) to compress hub assembly (102). Remove lock rings (103) and two half rings (104) (not shown). Note: Note the orientation of lock rings (103) and two ring halves (104) for assembly purposes.

Illustration 48

g01387556

54. Remove hub assembly (102), friction discs (105), and clutch plates (106) from clutch assembly (60). Note: Note the orientation of friction discs (105) and clutch plates (106) for assembly purposes.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 49

22/45

g01387573

55. Remove wave spring (107) and piston (108) from clutch assembly (60).

Illustration 50

g01387580

56. Remove seal rings (109) and (110) from piston (108).

Illustration 51

g01387592

57. Use a suitable lifting device to turn over clutch assembly (60) onto Tooling (H). The weight of clutch assembly (60) is approximately 54 kg (120 lb).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 52

23/45

g01387595

58. Use Tooling (P) to remove inner bearing (111), thrust disc (112), and gear (113) from clutch assembly (60). Note: Note the orientation of thrust disc (112) for assembly purposes.

Illustration 53

g01387755

59. Remove thrust disc (114) and gear assembly (115). Note: Note the orientation of thrust disc (114) for assembly purposes.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 54

g01387765

60. Remove bearing (116) from gear assembly (115).

Illustration 55

g01387820

61. Remove thrust disc (117) and washer (118). Note: Note the orientation of thrust disc (117) for assembly purposes.

Illustration 56

g01387824

Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11

24/45


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

25/45

62. Use Tooling (L) to compress hub assembly (119). Remove lock rings (120) and two half rings (121) (not shown). Note: Note the orientation of lock rings (120) and two ring halves (121) for assembly purposes.

Illustration 57

g01387846

63. Remove hub assembly (119), friction discs (122), and clutch plates (123). Note: Note the orientation of friction discs (122) and clutch plates (123) for assembly purposes.

Illustration 58

g01387852

64. Remove wave spring (124) and piston (125).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 59

26/45

g01387858

65. Remove seal rings (126) and (127) from piston (125).

Illustration 60

g01387876

66. Use Tooling (P) to remove inner bearing (128) and gear (129) from input shaft assembly (130). This is necessary at this time so that you can remove the remaining two clutch assemblies.

Illustration 61

g01387884

67. Remove bolts (131) to remove seal carrier (132).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 62

27/45

g01387892

68. Remove seal rings (133). Remove O-ring seals (134).

Illustration 63

g01387895

69. Attach Tooling (R) and a suitable lifting device to clutch assembly (135). The weight of clutch assembly (135) is approximately 61 kg (135 lb). Use Tooling (R) and the suitable lifting device to remove clutch assembly (135). Position clutch assembly (135) onto Tooling (H).

Illustration 64

g01387898

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

28/45

70. Use Tooling (P) to remove inner bearing (136), spacer (137), and gear (138) from clutch assembly (135).

Illustration 65

g01388168

71. Remove spacer (139) and thrust disc (140) from clutch assembly (135). Note: Note the orientation of thrust disc (140) for assembly purposes. 72. Remove gear assembly (141), thrust disc (142), and washer (143). Note: Note the orientation of thrust disc (142) for assembly purposes.

Illustration 66

g01388185

73. Remove bearing (144) from gear assembly (141).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 67

29/45

g01388208

Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force.

74. Use Tooling (L) to compress hub assembly (145). Remove lock rings (146) and two half rings (147) (not shown). Note: Note the orientation of lock rings (146) and two ring halves (147) for assembly purposes.

Illustration 68

g01388240

75. Remove hub assembly (145), friction discs (148), and clutch plates (149).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Note: Note the orientation of friction discs (148) and clutch plates (149) for assembly purposes.

Illustration 69

g01388243

76. Remove wave spring (150) and piston (151).

Illustration 70

g01388246

77. Remove seal rings (152) and (153) from piston (151).

Illustration 71

g01388263

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11

30/45


Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading


12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...

Illustration 72

31/45

g01388277

78. Use a suitable lifting device to turn over clutch assembly (135) onto Tooling (H). The weight of clutch assembly (135) is approximately 41 kg (90 lb). 79. Attach Tooling (S) to clutch assembly (135) to remove inner bearing (154). Remove thrust race (155), thrust disc (156), thrust disc (157), and gear assembly (158). Note: Note the orientation of thrust discs (156) and (157) for assembly purposes.

Illustration 73

g01388296

80. Remove roller bearing assembly (159) and thrust disc (160) from clutch assembly (135). Note: Note the orientation of thrust disc (160) for assembly purposes.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2021/1/11


Turn static files into dynamic content formats.

Create a flipbook