Antelco Irrigation Equipment Catalogue

2020 IRRIGATION EQUIPMENT CATALOGUE

METRIC www.antelco.com

PUTTING WATER WHERE IT COUNTS!®

NEW PRODUCTS Rotor Rain® Plus Mini Sprinklers

Page 27

A range of Mini Sprinklers incorporating: Ÿ Anti-insect spinner Ÿ Easy disassembly Ÿ Durable double frame Ÿ 10 colour coded bases Ÿ 3/8" or 1/2" male threaded inlet size options Ÿ Optional snap-off deector for young trees

Rotor StakeTM

Page 52

A 3/8" female threaded stake to accommodate the ® TM Rotor Rain Plus and Rotor Max or any 3/8" sprinkler, incorporating: Ÿ A self piercing tool on the base of the stake to punch a hole for the adaptor. Ÿ Accepts multiple sized tube adaptors - micro tube, 10 mm and 13 mm Ÿ Robust design Ÿ Tube retainer

Rotor MaxTM / ReuZit® Sprinkler Deector Page 30 TM

A snap-on Deector that converts a Rotor Max or ® ReuZit Sprinkler into a half circle spray pattern.

Antelco is committed to product development and improvement so specications may change without notice and without incurring liability. © All photographs and drawings used in the Antelco catalogue are the property of Antelco Pty Ltd and are protected by Copyright. Reproduction in whole or part, in any form of medium, without written approval from Antelco Pty Ltd is prohibited.

TM ® Trademarks and Registered Trademarks, where indicated, are owned by Antelco Pty Ltd.

CONTENTS 1 2 3 4 5 6 7 9 10 11 12

DRIPPERS

Spectrum™ Adjustable Flow Single Piece Jets Micro Spray Jets: Caps and Bases Micro Spray Jets: Assembled Micro Spray Stake Assemblies Vari-Jets™ CFa AgSpray™ CFd® Downspray Frame Jets™

13 14 15 16 17 18 19 20 21

SPRAYS

Rotor Spray™ Mini Sprinklers Rotor Rain® Mini Sprinklers Rotor Rain® Plus Mini Sprinklers Rotor Max™ Midi Sprinklers Rotor Max™ Deector ReuZit® Recycled Water Products

23 25 27 29 30 31

SPRINKLERS

Valves eZyvalve™4 Pressure Regulators

33 35 36

VALVES

Micro Fittings Take-Off Fittings Xpando® Take-Off Fittings & Grommets Xpando® Take-Off Director Directors, End Plugs & Saddles Joiners and Elbows Tees Double Barb “DB” Fittings™ Super Tough “ST” Fittings™ Ratchet Clamps Asta® Stakes and Rigid Risers Micro Stakes Hold Down Stakes Mini Sprinkler Stakes Tap Fittings Filters

37 39 40 41 42 43 44 45 47 48 49 50 51 52 53 54

FITTINGS

Installation Tools Installation Guidelines

55 56

ACCESSORIES

Shrubbler® 360° & 180° Adjustable Flow Potstream® Adjustable Flow Mini Bubbler 360° Adjustable Flow Agri Drip™ Classic Drippers Midi Drip™ Drippers Asta® Drip Pressure Compensating - Spike Drippers CETA® Pressure Compensating Drippers Shrubbler® 360° Pressure Compensating Pinch Drip™ Pressure Compensating Agri Drip™ Pressure Compensating Drippers Dripper Selection Guide

Shrubbler® 360o & 180o Adjustable Flow The original Shrubbler® with ow adjustment. Flow and coverage can be altered by rotating the cap.

Features Ÿ Fingertip ow control with shut-off option. ® Ÿ Spike models anchor Shrubbler at the plant. Ÿ Spike models suit 4 mm ID micro tube. Ÿ Barb model for direct attachment to micro and supply tubes. ® Ÿ 4 mm threaded model for installation into Rigid Risers and Asta Stakes. Ÿ 1/2" threaded model for riser pipe installations.

Applications Pots, tubs, landscaped gardens and nurseries. Ideal for hanging baskets.

In-Line Spike model suitable for planter boxes.

Performance Chart - Fully open (approx. 22 clicks)

DRIPPERS

Pattern

180o

Pressure (kPa)

Flow (lph)

Diameter (m)

Radius (m)

100 150 200

33 41 49

0.4 0.6 0.9

0.4 0.5 0.6

Flow Rate 360o & 180o

Flow (lph)

60 50

200 kPa

40

150 kPa 100 kPa

30 20 10

Shrubbler® Thread 4 mm

0

2

4

6

8

10 12 14 Number of Clicks

20

22

Radius of Throw 180o

1.0

Shrubbler® Spike Inlet 4 mm

18

16

Diameter of Throw 360o

0.7 200 kPa

0.8 0.6

150 kPa

0.4

100 kPa

0.2

Radius (m)

Diameter (m)

ADJUSTABLE

Shrubbler® Barb 4 mm

360o

0.6

200 kPa

0.5

150 kPa

0.4

100 kPa

0.3 0.2 0.1

0 10

12

16 18 14 Number of Clicks

20

22

0 8

10

18 12 14 16 Number of Clicks

20

22

Ordering Information - Shrubbler® 360o Base Type Barb 4 mm Thread 4 mm Thread 1/2" FNPT Spike Spike In-Line Shrubbler® Thread 1/2" Female

Shrubbler® In-Line Spike Inlet 4 mm

1

Order Code

Pack Quantity

Packs Per Carton

Carton (kg)

31445 31415 31425 31495 30995

100 100 25 25 25

65 65 70 40 40

11.5 14.0 8.3 6.3 6.3

Order Code

Pack Quantity

Packs Per Carton

Carton (kg)

31245 31215 31225 31295

100 100 25 25

65 65 70 40

11.5 14.0 8.3 6.3

Ordering Information - Shrubbler® 180o Base Type Barb 4 mm Thread 4 mm Thread 1/2" FNPT Spike * For product specications refer to Mini Bubbler (Page 3)

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Potstream® Adjustable Flow The Potstream® is a side mounted watering solution for pot plants and containers. The adjustable gentle stream pattern minimises soil erosion and the variable ow rate and pattern radius allows for use in various pot sizes.

Features Ÿ Variable ow rate and pattern size suits pot diameters of 200 mm and upwards. Ÿ Suits pot wall thickness up to 40 mm. Ÿ Side mounted installation for neat location of the supply tube. Ÿ Low application rate and gentle stream pattern. Ÿ Easily adjustable knob for varying spray patterns.

Applications Potted plants, planter boxes and containers.

Performance Chart ®

Flow (lph)

Radius (mm)

50 100 150 200 250 300

0 - 16 0 - 22 0 - 27 0 - 31 0 - 36 0 - 39

0 - 235 0 - 245 0 - 260 0 - 280 0 - 300 0 - 330

DRIPPERS

Pressure (kPa)

Ordering Information - Potstream® Description Potstream® Adjustable Flow

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

31455

25

20

6.3

Dimensions Assembled

UV Stabilised Material

HEIGHT 220 mm STAKE WIDTH 22 mm KNOB DEPTH 75 mm WEIGHT (approx.)

11 g

Colour

polypropylene STAKE HDPE KNOB

Base/Connection Type

Black Black Inlet

BARB 4.5 mm

ADJUSTABLE

Specications

Typical System Key: A - Pressure Regulator B - Nut & Tail C - Filter D - Elbow E - Take-off/Joiner F - Tidy Bow™ Elbow

G - Potstream® H - Tee I - End Sleeve J - 13 mm Supply Tube K - 4 mm Micro Tube

G K

I

F

A B C

E J

H

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

D

2

o

Mini Bubbler 360 Adjustable Flow High volume output with gentle umbrella pattern. Flow and coverage can be altered by rotating the cap.

Features Ÿ Fingertip ow control with shut-off option. Ÿ Spike model to anchor Mini Bubbler at the plant. Ÿ Barb model for direct attachment to micro and supply tubing. ® Ÿ 4 mm threaded model for installation into Rigid Risers and Asta Stakes. Ÿ 1/2" threaded model for riser pipe installations.

Applications Street trees and shrubs. Higher ow rates allow for short watering times.

Performance Chart - Fully open (approx. 22 clicks) 360o

DRIPPERS

Pattern Pressure (kPa)

Flow (lph)

Diameter (m)

100 150 200

100 119 130

0.2 0.3 0.5

Flow Rate 120

200 kPa 150 kPa

100

100 kPa

80 60 40 20 0

Mini Bubbler Spike Inlet 4 mm

6

4

2

8

10 12 14 Number of Clicks

16

18

20

22

Diameter of Throw 0.6 200 kPa

0.5 Diameter (m)

ADJUSTABLE

Flow (lph)

140

0.4 0.3

150 kPa

0.2

100 kPa

0.1 0

Mini Bubbler Barb 4 mm

10

12

16 14 Number of Clicks

18

20

Ordering Information - Mini Bubbler Base Type

Mini Bubbler Thread 4 mm

Barb 4 mm Thread 4 mm Thread 1/2" FNPT Spike

HEIGHT WIDTH DEPTH WEIGHT (approx.)

UV STABILISED MATERIAL

3

Order Code

Pack Quantity

Packs Per Carton

Carton (kg)

31745 31715 31725 31795

100 100 25 25

65 65 70 40

11.0 13.8 8.2 6.3

Thread

Thread 1/2"

Specications - Shrubbler® & Mini Bubbler Dimensions Assembled

Mini Bubbler Thread 1/2" Female

22

BASE CAP

BASE/CONNECTION TYPE: Inlet

Barb

Spike

23 mm 23 mm 34 mm 135 mm 20 mm 20 mm 26 mm 42 mm 16 mm 16 mm 26 mm 16 mm 1.6 g 2.0 g 4.3 g 5.4 g polypropylene acetal polypropylene polypropylene polypropylene polypropylene polypropylene polypropylene BARB 4 mm

10-32 UNF THREAD 4 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

THREAD 1/2" FNPT

BARB 4 mm

Agri DripTM Classic Dripper A sealed turbulent ow path dripper that provides consistent and uniform performance at an economical price.

Features Ÿ Colour coded bases for easy identication: 2 lph (Red), 4 lph (Black) & 8 lph (Green). Ÿ Positive barb connection to suit 4 mm ID micro tube or direct connection to supply tubing. Ÿ Constructed of UV stabilised plastic for long life.

Applications Economical dripper for landscape, horticultural tree and row crops and vineyards.

Performance Chart Flow Rate (lph)

Pressure (kPa)

4 lph

8 lph

1.4 1.7 2.0 2.2 2.4

3.0 3.6 4.1 4.6 5.0

6.0 7.4 8.4 9.3 10.2

MINIMUM FLOW PATH DIMENSION (mm)

0.9 x 0.7

1.3 x 0.8

1.8 x 1.1

DRIPPERS

2 lph

50 75 100 125 150

Flow Rate Agri DripTM Classic 2 lph

16 8 lph

14

FIXED FLOW

Flow (lph)

12 10 8

4 lph

6 2 lph

4 2 0

50

100

150 Pressure (kPa)

200

250

300

Ordering Information - Agri DripTM Classic Agri DripTM Classic 4 lph

Description 2 lph 4 lph 8 lph

Agri DripTM Classic 8 lph

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

30225 30245 30285

100 100 100

85 85 85

10.4 10.4 10.4

Specications Dimensions Assembled HEIGHT DIAMETER WEIGHT (approx.)

UV Stabilised Material

23 mm BASE 20 mm CAP 1.3 g

Base/Connection Type

polypropylene Inlet polypropylene Outlet

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

BARB 4 mm SPOUT 4 mm

4

TM

Midi Drip Dripper 4 lph dripper with barb and spike options. For efcient delivery of water to individual plants in pots and gardens.

Features Ÿ Take apart for easy inspection and cleaning. Ÿ Barb model for direct insertion into tubing. Ÿ Spike model to anchor Midi Drip™ at the plant.

Applications Shrubs and owers, fruit trees, vines and tomatoes in a wide range of situations from home gardens to large scale nurseries.

DRIPPERS

Performance Chart Pressure (kPa)

Flow (lph)

50 75 100 125 150

2.6 3.2 4.0 4.6 5.2

MINIMUM FLOW PATH DIMENSION (mm)

0.5 x 0.6

Flow Rate 8 7 Flow (lph)

FIXED FLOW

6 5 4 3 2 1 0

50

100

150 Pressure (kPa)

200

250

300

Midi DripTM Spike 4 mm

Ordering Information - Midi DripTM Base Type Barb 4 mm Spike 4 mm

Order Code

Pack Quantity

Packs Per Carton

Carton (kg)

30145 30195

100 25

80 50

12.7 6.4

Midi DripTM Barb 4 mm

Specications Dimensions Assembled HEIGHT LENGTH WIDTH WEIGHT (approx.)

5

Barb

Spike

17 mm 35 mm 9 mm 1.5 g

123 mm 49 mm 9 mm 4.6 g

UV Stabilised Material BODY KEY SPIKE

Base/Connection Type

polypropylene polypropylene Inlet polypropylene

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

BARB 4 mm

®

Asta Drip PC Spike Dripper A landscape and nursery dripper incorporating an anchoring spike that delivers precise amounts of water direct to the plant root zone. Asta® pressure compensating (PC) spike dripper has a sealed turbulent ow path and diaphragm to maintain uniform discharge rates over a wide range of pressures.

Features Ÿ Three colour-coded ow rates: 2 lph (Red), 4 lph (Black) & 8 lph (Green). Ÿ Turbulent ow path & self-ushing cleaning action at low pressure. Ÿ Outlet includes insect bafe to minimise blockages. Ÿ Inlet barb has built-in lter. Ÿ UV stabilised materials for long life. Ÿ Self-ushing cleaning action at low pressures.

Applications Nurseries, shade houses, tree lots and landscape applications.

Performance Chart Flow Rate (lph)

Pressure (kPa)

4 lph

8 lph

50 100 150 200 250 300 350

2.0 2.3 2.3 2.3 2.3 2.3 2.2

3.6 4.3 4.4 4.6 4.7 4.7 4.6

5.8 7.8 8.0 8.2 8.3 8.2 8.0

MINIMUM FLOW PATH DIMENSION (mm)

0.7 x 0.6

0.8 x 0.8

1.2 x 0.9

DRIPPERS

2 lph

Flow Rate 9

PRESSURE COMPENSATING

8 lph

8

Flow (lph)

7 ®

Asta Drip PC 2 lph Spike

6 5

4 lph

4 3 2 lph

2 1 0

50

100

150 Pressure (kPa)

200

250

300

Ordering Information - Asta® Drip PC Spike Order Code

Description ®

Asta Drip PC 4 lph Spike

Pack Quantity

Packs per Carton

Carton (kg)

2 lph

30735

25

50

7.1

4 lph

30745

25

50

7.1

8 lph

30755

25

50

7.1

Specications Dimensions Assembled

®

Asta Drip PC 8 lph Spike

HEIGHT WIDTH DEPTH WEIGHT (approx)

UV Stabilised Material

144 mm SPIKE 33 mm BASE 17 mm DIAPHRAGM 4.5 g

Base/Connection Type

polypropylene Inlet polypropylene Outlet silicone rubber

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

BARB 4 mm SPOUT 4 mm

6

®

CETA PC Dripper A take apart pressure compensating dripper incorporating a turbulent ow path and diaphragm for uniform ow rates over a wide range of operating pressures.

Features Ÿ Take apart for easy inspection and cleaning. Ÿ Self-ushing cleaning action at low pressure. Ÿ Outlet includes anti-insect bafe to reduce risk of blockages. Ÿ 4 mm barbed dripper range with colour coded bases for easy identication 2 lph (Red), 4 lph (Black) & 8 lph (Green). Ÿ 4 mm barbed range available with 4 mm barbed outlet options. ® Ÿ 4 lph PC Spike & In-Line Spike models to anchor CETA at the plant root. Ÿ Constructed of high quality UV, chemical & fertiliser resistant materials.

Applications Pots, planter boxes, balcony, patios and landscape.

Performance Chart Flow (lph)

Pressure (kPa)

4 lph

8 lph

1.9 2.0 2.2 2.3 2.3 2.3 2.2

3.3 3.8 4.2 4.4 4.4 4.4 4.3

6.2 7.9 7.9 8.1 8.1 8.0 7.8

MINIMUM FLOW PATH DIMENSION (mm)

0.7 x 0.6

0.8 x 0.8

1.2 x 0.9

DRIPPERS

2 lph

50 100 150 200 250 300 350

PRESSURE COMPENSATING

Ordering Information - CETA® PC 4 lph Spike Base Type Spike In-Line Spike

CETA® PC In-Line Spike 4 lph Inlet 4 mm

Order Code

Pack Quantity

Packs Per Carton

Carton (kg)

30625 30655

25 25

60 50

8.7 7.7

Ordering Information - CETA® PC with 4 mm Barb Outlet CETA® PC Spike 4 lph Inlet 4 mm

Order Code

Pack Quantity

Packs Per Carton

Carton (kg)

2 lph

30545

100

60

13.5

4 lph

30555

100

60

13.5

8 lph

30565

100

60

13.5

Flow

CETA® PC 2 lph Barb 4 mm Outlet 4 mm

Specications ®

CETA PC 4 lph Barb 4 mm Outlet 4 mm

Dimensions Assembled HEIGHT WIDTH DEPTH WEIGHT (approx.)

UV STABILISED MATERIAL ®

CETA PC 8 lph CONNECTION TYPE: Barb 4 mm Outlet 4 mm

7

BASE/SPIKE CAP DIAPHRAGM ADAPTOR Inlet Outlet

CETA® PC with 4 mm barb outlet

CETA® PC Spike/ In-Line Spike

35 mm 20 mm 16 mm 2.0 g polypropylene polypropylene silicone rubber acetal BARB 4 mm BARB 4 mm

135 mm 36 mm / 42 mm 16 mm 5.0 g polypropylene polypropylene silicone rubber

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

BARB 4 mm SPOUT 4 mm

®

CETA PC Dripper A take apart pressure compensating dripper incorporating a turbulent ow path and diaphragm for uniform ow rates over a wide range of operating pressures.

Features Ÿ Low manufacturing coefcient of variation (Cv) provides high performance (conforms to ISO 9261). Ÿ Three colour coded ow rates: 2 lph (Red), 4 lph (Black) & 8 lph (Green). Ÿ Self-ushing cleaning action at low pressures. Ÿ Large clog resistant turbulent ow path. ® Ÿ The CETA dripper is able to be taken apart for inspection and cleaning. Ÿ Anti-insect bafe to deter insect entry. Ÿ Constructed of high quality UV, chemical & fertiliser resistant materials.

Applications Vineyards, orchards, row crops and landscape.

Performance Chart Flow (lph)

Pressure (kPa)

4 lph

8 lph

50 100 150 200 250 300 350

1.9 2.0 2.2 2.3 2.3 2.3 2.2

3.3 3.8 4.2 4.4 4.4 4.4 4.3

6.2 7.9 7.9 8.1 8.1 8.0 7.8

MINIMUM FLOW PATH DIMENSION (mm)

0.7 x 0.6

0.8 x 0.8

1.2 x 0.9

DRIPPERS

CETA® PC 2 lph Barb 4 mm

2 lph

Flow Rate 9

Flow (lph)

7 6 5 4 lph

4 3

2 lph

2 1 0

CETA® PC 4 lph Barb 4 mm

50

100

150 Pressure (kPa)

200

250

300

Order Code

Pack Quantity

Packs Per Carton

Carton (kg)

2 lph

30425

100

70

13.3

4 lph

30445

100

70

13.3

8 lph

30485

100

70

13.3

Ordering Information - CETA® PC Barb Flow

PRESSURE COMPENSATING

8 lph

8

Specications

CETA® PC 8 lph Barb 4 mm

Dimensions Assembled

CETA® PC

HEIGHT WIDTH DEPTH WEIGHT (approx.)

BASE UV STABILISED CAP MATERIAL DIAPHRAGM CONNECTION TYPE: Inlet Outlet

25 mm 20 mm 16 mm 1.7 g polypropylene polypropylene silicone rubber BARB 4 mm SPOUT 4 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

8

Shrubbler® 360o Pressure Compensating A pressure compensating drip emitter that provides a xed diameter over a wide range of operating pressures. Gentle stream action with uniform coverage for all emitters on the same supply tube.

Features Ÿ Pressure compensating operation maintains diameter of throw over a wide range of inlet pressures. Ÿ Take apart for easy inspection and cleaning. Ÿ Coloured cap for easy identication. Ÿ UV stabilised materials for long life. Ÿ Resistant to common agricultural chemicals & fertilisers. Ÿ Patented design.

Applications Pots, planter boxes, balcony, patio and landscape.

Performance Chart 360o

DRIPPERS

Pressure (kPa) 100 150 200 250 300

Flow (lph)

Diameter (m)

24 29 33 36 38

0.3 0.4 0.4 0.4 0.4

Flow Rate 40

Flow (lph)

PRESSURE COMPENSATING

50

30 20 10 0

50

100

150

200

250

300

Pressure (kPa)

Shrubbler® 360o PC Spike Inlet 4 mm

Ordering Information - Shrubbler® 360o PC Description Barb 4 mm Spike

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

31685 31695

100 25

70 60

13.1 8.5

Specications Dimensions Assembled Shrubbler® 360o PC Barb 4 mm

HEIGHT WIDTH DIAMETER WEIGHT (approx.)

BASE CAP DIAPHRAGM BASE/CONNECTION TYPE: Inlet UV STABILISED MATERIAL

9

Barb

Spike

25 mm 20 mm 15 mm 1.7 g polypropylene polypropylene silicone rubber BARB 4 mm

135 mm 16 mm 26 mm 5.4 g polypropylene polypropylene silicone rubber BARB 4 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Pinch DripTM Pressure Compensating Dripper A high performance pressure compensating dripper with a sealed turbulent ow path and diaphragm to maintain uniform ow rates over a wide range of operating pressures. Low prole design to minimise risk of dislodgement from supply tubing and ergonomic nger grips for ease of installation.

Features Ÿ Low manufacturing coefcient of variation (Cv) to provide high performance (conforms to ISO 9261). Ÿ Three colour coded ow rates: 2 lph (Red), 4 lph (Black) & 8 lph (Green). Ÿ Self-ushing cleaning action at low pressures. Ÿ Insect bafe to reduce risk of blockages. Ÿ Inlet barb has built-in lter. Ÿ UV stabilised materials for long life. Ÿ Resistant to common agricultural chemicals & fertilisers.

Applications Vineyards, orchards, row crops and landscape.

Performance Chart Flow (lph)

Pressure (kPa)

4 lph

8 lph

2.1 2.3 2.3 2.4 2.4 2.3 2.2

3.4 4.1 4.4 4.6 4.6 4.6 4.5

5.7 7.2 7.4 7.6 7.7 7.5 7.3

MINIMUM FLOW PATH DIMENSION (mm)

0.7 x 0.6

0.8 x 0.8

1.2 x 0.9

DRIPPERS

Flow Rate 9 8

8 lph

Flow (lph)

7 6 5

4 lph

4 3 2 lph

2 1 0

Pinch DripTM PC 4 lph Barb 4 mm

50

100

150 Pressure (kPa)

300

250

Ordering Information - Pinch DripTM PC Description 2 lph 4 lph 8 lph

Pinch DripTM PC 8 lph Barb 4 mm

200

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

30705 30715 30725

100 100 100

85 85 85

10.1 10.1 10.1

PRESSURE COMPENSATING

Pinch DripTM PC 2 lph Barb 4 mm

2 lph

50 100 150 200 250 300 350

Specications Dimensions Assembled HEIGHT WIDTH DEPTH WEIGHT (approx.)

UV Stabilised Material

25 mm CAP 28 mm BASE 15 mm DIAPHRAGM 1.1g

Base/Connection Type

polypropylene Inlet polypropylene Outlet silicone rubber

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

BARB 4 mm SPOUT 4 mm

10

Agri DripTM Pressure Compensating Drippers A sealed turbulent ow path pressure compensating dripper incorporating a diaphragm that maintains a uniform ow rate over a wide range of operating pressures.

Features Ÿ Three models: 2 lph, 4 lph & 8 lph. Ÿ Positive barb connection to suit 4 mm ID tube or connect directly to supply tubing. Ÿ UV stabilised materials for long life. Ÿ Resistant to common agricultural chemicals & fertilisers.

Applications Horticultural tree and row crops, vineyards and landscape.

Performance Chart Flow (lph)

Pressure (kPa)

4 lph

8 lph

1.7 2.0 2.1 2.1 2.1 2.1 2.1

2.8 3.9 4.1 4.3 4.4 4.5 4.5

7.3 8.1 8.4 8.6 8.6 8.3 7.6

MINIMUM FLOW PATH DIMENSION (mm)

0.7 x 0.6

0.8 x 0.8

0.7 x 1.0

DRIPPERS

2 lph

50 100 150 200 250 300 350

Flow Rate 9 8 lph

8 7 Flow (lph)

PRESSURE COMPENSATING

Agri DripTM 2 lph PC Dripper Barb 4 mm

6 5

4 lph

4 3 2 lph

2 1 0

50

100

Agri DripTM 4 lph PC Dripper Barb 4 mm

150 Pressure (kPa)

250

300

Ordering Information - Agri DripTM PC Flow 2 lph 4 lph 8 lph

Agri DripTM 8 lph PC Dripper Barb 4 mm

Order Code

Pack Quantity

Packs Per Carton

Carton (kg)

30325 30345 30365

100 100 100

75 75 75

10.6 10.6 10.6

Specications Dimensions Assembled HEIGHT DIAMETER WEIGHT (approx.)

11

200

UV Stabilised Material

23 mm BASE 20 mm CAP 1.3 g DIAPHRAGM

Base/Connection Type

polypropylene Inlet polypropylene Outlet silicone rubber

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

BARB 4 mm SPOUT 4 mm

Dripper Selection Guide

Type

Brand

Adjustable

Shrubbler

0 - 33 lph

Potstream

0 - 22 lph

Mini Bubbler

0 - 100 lph

Native Gardens

Shrubs Trees

Pots / Cleanable Anchored Planters

Tanks

Self Flushing

Insect Baffle

DRIPPERS

Nominal Garden Beds Flow Rate

2 lph

Fixed

Agri Drip Classic

4 lph

8 lph

2 lph

CETA

4 lph

8 lph

2 lph

Pressure Compensating

Pinch

4 lph

8 lph

2 lph

Asta PC Spike

4 lph

8 lph

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

12

SpectrumTM 360o Adjustable Spray An adjustable ow, full circle vortex sprayer with ne water droplets. Flow and coverage can be altered by rotating the cap.

Features Ÿ Finger tip ow control with shut-off option. Ÿ Spike model to anchor Spectrum™ at the plant. Ÿ 4 mm barb model for direct attachment to micro or supply tubing. ® Ÿ 4 mm thread for installation into Rigid Risers and Asta Stakes or Micro Stakes. Ÿ 1/2” thread for riser pipe installations.

Applications Pots, tubs, ground cover, landscaped gardens and nurseries. Waters large garden areas when used with Asta® Stakes and Risers.

Performance Chart - Fully open (approx. 22 clicks) 360o

SPRAYS

Pressure (kPa) 100 150 200

Flow (lph)

Diameter (m)

64 78 90

2.8 3.6 4.0

Flow Rate 100 200 kPa 150 kPa

Flow (lph)

80

100 kPa

60 40 20 0

10 12 Number of Clicks

20

22

100 kPa

2 1

10

12

16 18 Number of Clicks

14

20

22

Ordering Information - SpectrumTM 360o Order Code

Pack Quantity

Packs Per Carton

Carton (kg)

32045 32015 32025 32095

50 50 25 25

100 100 65 40

11.8 13.8 9.1 6.9

Thread

Thread 1/2"

Specications Dimensions Assembled

Barb

HEIGHT WIDTH DEPTH WEIGHT (approx.)

BASE UV STABILISED CAP MATERIAL DEFLECTOR

13

18

3

Barb 4 mm Thread 4 mm Thread 1/2" Female Spike

SpectrumTM Thread 1/2" Female

16

200 kPa 150 kPa

Base Type

SpectrumTM Thread 4 mm

14

4

0

SpectrumTM Barb 4 mm

8

Diameter of Throw Diameter (m)

SpectrumTM Spike Inlet 4 mm

6

4

2

BASE/CONNECTION TYPE:

Inlet

Spike

26 mm 26 mm 37 mm 137 mm 20 mm 20 mm 26 mm 42 mm 16 mm 16 mm 26 mm 16 mm 1.7 g 2.1 g 4.9 g 5.5 g polypropylene acetal polypropylene polypropylene polypropylene polypropylene polypropylene polypropylene acetal acetal acetal acetal BARB 4 mm

10-32 UNF THREAD 4 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

THREAD 1/2" FNPT

BARB 4 mm

Single Piece Jets Economical fan spray jet for effective watering.

Features Ÿ Winged base with ‘Quick’ thread for easy installation. Ÿ No tools required. Ÿ Choice of three spray patterns – 360°, 180°, 90°. Ÿ Four colour coded ow rates.

Applications Home and landscaped gardens and horticultural applications.

Accessories Asta® Stake, Rigid Riser and Micro Stake.

Performance Chart 360o

180o

90o

Pattern

1.0 mm Blue 1.5 mm Green

Single Piece Jet Blue 90o

1.7 mm Black 1.9 mm Red

Pressure (kPa)

Flow (lph)

Diameter (m)

50 100 150 50 100 150 50 100 150 50 100 150

25 35 43 48 70 88 62 90 113 77 110 134

1.6 2.0 2.4 2.0 2.4 2.8 2.4 2.8 3.2 2.5 3.0 3.4

Radius (m) 0.8 1.0 1.2 1.0 1.2 1.5 1.2 1.5 1.8 1.4 1.7 2.0

1.1 1.4 1.7 1.3 1.6 1.9 1.6 1.9 2.2 1.8 2.1 2.4

SPRAYS

Nozzle Size & Colour

Ordering Information - Single Piece Jets Spray Pattern & Colour

Single Piece Jet Green 180o

Single Piece Jet Red 360o

360o Blue 180o Blue 90o Blue 360o Green 180o Green 90o Green 360o Black 180o Black 90o Black 360o Red 180o Red 90o Red

Order Code

Pack Quantity

Packs Per Carton

Carton (kg)

15445 15425 15415 15545 15525 15515 15645 15625 15615 15745 15725 15715

100 100 100 100 100 100 100 100 100 100 100 100

250 250 250 250 250 250 250 250 250 250 250 250

16.6 16.6 16.6 16.6 16.6 16.6 16.6 16.6 16.6 16.6 16.6 16.6

Specications Dimensions HEIGHT WIDTH across wings WEIGHT (approx.)

UV Stabilised Material 22 mm 12 mm 0.6 g

acetal

Base/Connection Type Inlet

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

‘QUICK’ THREAD 4 mm

14

Micro Spray Jets: Caps and Bases A large variety of ow rates and spray patterns are achievable when the range of caps and bases are assembled into two piece jets.

Features Ÿ Caps available in eight spray patterns. Ÿ Eight colour coded bases to identify ow rate. Ÿ Jet assemblies made to order. Ÿ Caps and bases can be ordered separately.

Applications Assemblies suit garden bed watering and landscaped areas.

Accessories Asta® Stake, Rigid Riser and Micro Stake.

Ordering Information - Spray Caps

SPRAYS

Spray Pattern & Colour

300o 360o 360o 360o 18 hole 15 hole 12 hole 10 hole

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

10845 10855 10865 10875 10835 10825 10815 10885

100 100 100 100 100 100 100 100

500 500 500 500 500 500 500 500

15.1 15.1 15.1 15.1 15.1 15.1 15.1 15.1

Base Type

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

Winged Winged Winged Winged Winged Hexagon Hexagon Hexagon

10705 10725 10715 10735 10755 10975 10945 10985

100 100 100 100 100 100 100 100

310 310 310 310 310 350 350 350

17.2 17.2 17.2 17.2 17.2 17.1 17.1 17.1

360o x 18 hole 360o x 15 hole 360o x 12 hole 300o x 10 hole 270o (3 x 90o) 180o fan 90o fan Strip (2 x 20o)

Ordering Information - Jet Bases 270o (3 x 90o)

180o fan

90o fan

Strip (2 x 20o)

Winged Base ‘Quick’ Thread

0.8 mm

0.9 mm

Nozzle Size & Colour 0.8 mm Black 0.9 mm Brown 1.0 mm Blue 1.3 mm Green 1.5 mm Red 1.8 mm Orange 2.0 mm Grey 2.3 mm White

1.0 mm

Specications- Caps and Bases Dimensions

1.3 mm

Cap

Base Winged

HEIGHT 9 mm 20 mm 20 mm WIDTH 8 mm across wings 12.5 mm across ats 8 mm WEIGHT (approx.)

0.2 g 0.5 g 0.5 g UV STABILISED MATERIALS acetal acetal acetal BASE/CONNECTION TYPE: Inlet ‘QUICK’ THREAD 4 mm 10-32 UNF THREAD 4 mm Dimensions vary slightly depending on cap selected

1.5 mm

Hexagon Base 4 mm

Specications- Micro Spray Jets Winged (refer to Page 16) Dimensions Assembled

1.8 mm

15

2.0 mm

Base Hexagon

2.3 mm

Base Winged

HEIGHT WIDTH WEIGHT (approx.)

23 mm across wings 12.5 mm 0.7 g BASE acetal UV STABILISED MATERIALS CAP acetal BASE/CONNECTION TYPE: Inlet ‘QUICK’ THREAD 4 mm Dimensions vary slightly depending on selected base and cap assembly

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Micro Spray Jets: Assembled Two piece jets with precise watering patterns. Winged base for easy hand installation.

Features Ÿ Nine available spray patterns. Ÿ Colour coded bases for ow identication. Ÿ Caps feature a snap ring which rmly engages the base. Ÿ UV stabilised materials for long life.

Applications Landscape areas, home gardens, nurseries and horticultural applications.

Mist Jet ideal for greenhouse misting and hanging baskets. Strip Spray ideal for narrow garden beds. Use stakes and risers to elevate spray jets.

Accessories Asta® Stake, Rigid Riser and Micro Stake.

Performance Chart - All Micro Spray Jets 360o x 18

360o x 15

360o x 12

300o x 10

270o (3 x 90o)

Strip (2 x 20o)

90o

0.5 mm

0.6 mm

0.7 mm

0.7 mm

1.3 mm

1.4 mm

1.5 mm

Pattern

Pressure (kPa)

2.2 50 15 2.6 2.6 1.2 3.2 100 22 4.1 3.2 3.2 150 27 4.6 3.6 4.0 4.8 4.2 200 32 5.0 4.6 6.0 4.8 250 36 5.3 5.0 7.0 2.8 50 20 2.9 2.8 2.2 100 28 4.0 3.8 3.4 4.0 0.9 mm 4.4 150 34 4.8 4.2 5.4 Brown 5.0 200 39 5.6 5.2 6.6 5.8 250 44 6.0 6.2 7.4 2.6 50 22 3.6 2.8 2.4 100 33 4.9 3.8 4.4 4.8 1.0 mm 4.8 150 42 5.8 5.2 7.0 Blue 6.2 200 49 6.2 6.8 8.6 7.0 250 56 6.4 8.4 9.0 50 36 4.7 4.2 3.2 3.0 5.8 100 54 6.4 5.0 5.6 1.3 mm 6.2 150 68 7.0 6.0 7.2 Green 7.8 200 80 7.2 7.0 8.0 250 91 7.6 8.8 8.4 8.4 4.9 50 52 4.4 4.0 4.4 6.8 100 75 6.0 6.2 5.4 1.5 mm 8.2 150 92 7.4 8.4 8.8 Red 8.2 200 107 8.8 10.0 10.4 7.2 250 120 11.4 11.2 10.0 50 64 4.6 4.2 5.0 4.6 100 93 7.6 7.4 6.8 6.8 1.8 mm 150 115 9.4 8.8 8.2 8.8 Orange 200 135 10.8 10.0 8.0 10.0 250 152 11.6 10.6 7.3 11.4 50 80 5.0 4.6 5.3 4.8 100 115 8.2 7.4 7.5 7.6 2.0 mm 150 140 10.2 9.2 8.1 9.6 Grey 200 165 12.0 10.6 7.8 11.0 250 185 13.0 11.8 6.7 12.4 50 113 6.0 4.0 5.2 4.4 100 163 9.2 6.8 7.1 8.0 2.3 mm 150 200 11.6 9.6 7.3 10.4 White 200 235 13.0 10.6 7.0 11.4 250 265 14.2 11.6 6.7 12.4 50 13 100 18 0.36 mm 150 22 Yellow 200 25 250 28 * Ghosted gures indicate a change of performance from spray to mist.

0.8 mm Black

360o x 18 hole

90o fan

Mist Spray

180o fan

Strip Spray (2 x 20o)

360o x 18 hole

1.5 mm

Radius (m)

Diameter (m)

Flow (lph)

2.4 3.6 2.8 2.7 2.7 2.6 3.4 2.9 2.8 3.3 3.2 4.2 3.2 3.2 3.4 3.5 3.5 3.7 3.7 3.8 3.0 3.8 4.4 4.8 5.1 3.6 4.2 4.6 4.9 5.3 3.4 4.6 5.1 5.6 6.2 3.6 5.4 6.6 7.8 8.3

2.4 4.2 5.4 6.0 6.4 2.6 4.6 6.0 6.8 7.2 2.6 4.8 5.6 5.8 5.8 3.8 5.8 7.2 8.4 9.6 4.9 6.5 8.9 10.8 11.2 5.0 8.1 9.4 10.8 11.5 5.4 9.4 12.0 13.2 13.8 5.4 9.0 11.0 12.0 12.8

1.1 1.7 2.1 2.3 2.6 1.2 1.8 2.4 2.6 2.8 1.2 2.0 2.4 2.8 2.8 1.4 2.2 2.6 2.0 3.1 1.5 2.4 2.9 3.1 3.3 1.7 2.4 2.8 3.1 3.3 1.7 2.6 3.1 3.3 3.5 1.9 3.0 3.6 3.8 4.1

Mist

1.2 mm Diameter (m)

1.2 1.5 1.7 1.7 1.8 1.3 1.6 1.8 1.9 2.1 1.5 1.8 2.0 2.1 2.3 1.5 2.0 2.3 2.5 2.7 1.9 2.4 3.0 3.2 3.4 1.7 2.4 2.7 3.1 3.3 1.7 2.5 3.1 3.3 3.6 2.0 2.8 3.4 4.0 4.2

SPRAYS

Minimum opening size Size and colour

180o

1.0 0.8 0.9 0.8 0.8

Ordering Information - Micro Spray Jets: Winged Assembled

180o fan

90o fan

Spray Pattern 360o x 18 hole 180o fan 90o fan Strip Spray (2 x 20o) Mist 360o x 18 hole 180o fan 90o fan

Base Colour Blue Blue Blue Blue Yellow Green Green Green

Cap Colour Red Blue Black Black Black Black Black Black

Order Code 14945 14925 14115 14815 14995 14435 14235 14135

Pack Quantity 100 100 100 100 100 100 100 100

Packs per Carton 220 220 220 220 220 220 220 220

Carton (kg) 17.8 17.8 17.8 17.8 18.6 17.8 17.8 17.8

The above Spray Jet Assemblies are standard stock items. For non-standard spray jet assemblies select BASE Colour and CAP Colour with spray pattern. Allow two weeks for assembly and despatch. Urgent orders by arrangement. Minimum order - 1000 Assemblies.

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

16

Micro Spray Stake Assemblies Pre-assembled to save on installation time. Vari-Jet™ models have ow control to adjust radius of throw and reduce ow.

Features Ÿ Choice of four spray patterns. Ÿ Built-in hole punch. Ÿ Vari-Jet™ Spike assembled with 300 mm offtake tube and 150 mm Rigid Riser. Ÿ Vari-Jet™ Stake assemblies with 300 mm offtake tube on 300 mm stake. Ÿ UV stabilised materials for long life.

Applications Home and landscaped gardens.

Performance Chart - Vari-JetTM Spike 360o x 18

180o

90o

SPRAYS

Pattern Nozzle Size & Colour

Pressure (kPa)

Flow (lph)

Diameter (m)

Vari-JetTM Spike Red max. 1.5 mm

50 100 150 200 250

0 - 52 0 - 75 0 - 92 0 - 107 0 - 120

0 - 4.9 0 - 6.8 0 - 8.2 0 - 8.2 0 - 7.2

Radius (m) 0 - 1.9 0 - 2.4 0 - 3.0 0 - 3.2 0 - 3.4

0 - 1.5 0 - 2.4 0 - 2.9 0 - 3.1 0 - 3.3

* Ghosted gures indicate a change of performance from spray to mist.

Ordering Information - Vari-JetTM Spike Spray Pattern 360o x 18 hole 180o fan 90o fan

Base Colour

Cap Colour

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

Red Red Red

Red Blue Black

13345 13325 13315

10 10 10

14 14 14

4.8 4.8 4.8

Ordering Information - Winged Micro Spray Stake Assembly (refer page 16 for performance) Vari-JetTM Spike 180o fan

Spray Pattern 360o x 18 hole 180o fan 90o fan Strip Spray (2 x 20o)

Base Colour

Cap Colour

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

Blue Blue Blue Blue

Red Blue Black Black

17425 17435 17445 17455

25 25 25 25

19 19 19 19

12.4 12.4 12.4 12.4

Ordering Information - Vari-JetTM Stake Assembly (refer page 14 for performance data) Spray Pattern 360o x 18 hole 180o fan 90o fan

Base Colour

Cap Colour

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

Black Black Black

Black Black Black

17185 17195 17205

25 25 25

16 16 16

12.0 12.3 11.2

Specications

Winged Micro Spray Stake Assembly Vari-JetTM Stake Assembly

17

Dimensions Assembled

Vari-JetTM Spike

Winged Micro Spray Stake Assembly

Vari-JetTM Stake Assembly

HEIGHT WIDTH WEIGHT (approx.)

SPIKE/STAKE ADAPTOR UV RISER STABILISED KNOB MATERIALS OFF-TAKE TUBE BASE/CAP BASE/CONNECTION TYPE: Inlet

355 mm 55 mm 32 g polypropylene polypropylene HDPE polypropylene PVC acetal BARB 4 mm

345 mm 24 mm 26 g polypropylene acetal PVC acetal BARB 4 mm

360 mm 24 mm 28 g polypropylene acetal HDPE PVC acetal BARB 4 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

TM

Vari-Jets

A range of spray jets that incorporate a valve to adjust watering coverage and application.

Features Choice of spray patterns - 360o, 180o and 90o and mist.

Threaded for installation on Rigid Risers and Micro Stakes.

UV stabilised materials for long life.

Ÿ Ÿ Ÿ

Applications Home and landscaped gardens. Vari-Mist™ is ideal for adjustable overhead watering of plants in hanging baskets.

Accessories Asta® Stake, Rigid Riser and Micro Stake.

Performance Chart Cap Colour Options

Black

Black

Mist

Black Blue 180o

0.5 mm

1.2 mm

1.5 mm

1.5 mm

90o

Pattern Minimum opening size Nozzle Size & Base Colour

Pressure (kPa)

Flow (lph)

50 100 150 200 250 50 100 150 200 250

0 - 53 0 - 78 0 - 98 0 - 115 0 - 130 0 - 12 0 - 18 0 - 23 0 - 27 0 - 31

Yellow or Black max 1.5 mm

Yellow or Black max 0.36 mm

Diameter (m)

Radius (m)

0 - 4.9 0 - 6.8 0 - 8.2 0 - 8.2 0 - 7.2

0 - 1.9 0 - 2.4 0 - 3.0 0 - 3.2 0 - 3.4

SPRAYS

Black Red 360o x 18

0 - 1.5 0 - 2.4 0 - 2.9 0 - 3.1 0 - 3.3

0 - 1.0 0 - 0.8 0 - 0.9 0 - 0.8 0 - 0.8

* Ghosted gures indicate a change of performance from spray to mist.

Vari-JetTM 180o fan 10-32 UNF Thread 4 mm

Ordering Information - Vari-JetsTM Spray Pattern

Base Colour Type

360o x 18 hole 180o fan 90o fan Mist 360o x 18 hole 180o fan 90o fan Mist

Vari-JetTM 180o fan 10-32 UNF Thread 4 mm

Yellow 10-32 UNF Yellow 10-32 UNF Yellow 10-32 UNF Yellow 10-32 UNF Black 10-32 UNF Black 10-32 UNF Black 10-32 UNF Black 10-32 UNF

Cap Colour

Order Code

Pack Quantity

Packs Per Carton

Carton (kg)

Red Blue Black Black Black Black Black Black

13245 13225 13215 13295 13145 13125 13115 13195

50 50 50 50 50 50 50 50

80 80 80 80 80 80 80 80

11.3 11.3 11.3 11.7 11.3 11.3 11.3 11.7

Specications Dimensions Assembled HEIGHT WIDTH WEIGHT (approx.)

UV Stabilised Material

32 mm CAP 22 mm BASE 2.3 g KNOB

Base/Connection Type

acetal acetal Inlet HDPE

10-32 UNF THREAD 4 mm

Dimensions vary slightly depending on selected base and cap assembly Antelco irrigation equipment metric catalogue 2020 www.antelco.com

18

CFa AgSprayTM Single piece 360° stream open spray jet engineered for high performance at an affordable price.

Features Ÿ Colour coded for ow rate identication. Ÿ 12 Stream Hi-Lo watering pattern (a). Ÿ Robust proven C-Frame design. Ÿ No moving parts. Ÿ “Quick” thread inlet with sealing barb.

Applications Specically designed for orchards and horticultural crops.

Accessories Asta® Stake, Rigid Riser and Micro Stake.

Performance Chart 360o x 12 Streams - Hi Lo (a) 26o High x 12.5o Low Trajectory

Pattern/ Trajectory

Tested at 0.2 m above ground

SPRAYS

Nozzle Size & Colour 0.8 mm Black

0.9 mm Orange

CFa AgSprayTM Range

1.0 mm Blue

1.1 mm Purple

Typical System

1.5 mm Red

Pressure (kPa)

Flow (lph)

50 100 150 200 250 50 100 150 200 250 50 100 150 200 250 50 100 150 200 250 50 100 150 200 250

16 22 27 31 35 20 28 35 41 46 24 33 41 47 52 31 44 54 63 70 51 73 90 104 117

Diameter - (m) High Low 2.6 3.5 4.2 4.8 5.3 3.1 4.1 4.8 5.3 5.8 3.4 4.2 4.8 5.3 5.6 4.1 5.3 6.0 6.6 7.2 5.5 6.9 7.9 8.8 9.4

Hydraulic Flow Data Constant (k) Exponent (x)

2.0 2.8 3.4 3.9 4.4 2.3 3.1 3.8 4.4 4.9 2.4 3.4 4.1 4.7 5.2 3.2 4.2 4.9 5.5 6.0 4.3 5.6 6.5 7.3 8.0

2.464

0.48

2.589

0.52

3.479

0.49

4.196

0.51

6.634

0.52

Ordering Information - CFa AgSprayTM Nozzle Size & Colour 0.8 mm Black 0.9 mm Orange 1.0 mm Blue 1.1 mm Purple 1.5 mm Red

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

13005 13075 13015 13065 13055

100 100 100 100 100

90 90 90 90 90

15.0 15.0 15.0 15.0 15.0

Ordering Information - CFa AgSprayTM on Micro Stake w/ 600mm Tube & Adaptor Nozzle Size & Colour 0.8 mm 0.9 mm 1.0 mm 1.1 mm 1.5 mm

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

41605 41675 41615 41665 41655

25 25 25 25 25

5 5 5 5 5

6.9 6.9 6.9 6.9 6.9

Specications Dimensions

CFa AgSprayTM on Micro Stake with 600 mm Tube and Adaptor

19

HEIGHT WIDTH DEPTH WEIGHT (approx.)

Base/Connection Type

UV Stabilised Material 34 mm 25 mm 8 mm 1.4 g

acetal

Inlet

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

‘QUICK’ THREAD with sealing barb 4 mm

CFd® Downspray The patented C-Frame Downspray is a 360° spray jet that distributes water evenly across the wetted surface area. Stake assembly options provide savings in labour and installation time.

Features Ÿ 45° downspray reduces the effect of wind. Ÿ Gentle spray minimises damage to delicate plant foliage. Ÿ Galvanised wire stake assembly incorporates shut-off clip to stop ow. ® Ÿ Asta Stake assembly incorporates a hole punch for easy installation. Ÿ Three colour coded frames to identify ow rates. Ÿ Quick insertion thread with leak-proof design. Ÿ UV stabilised materials.

Applications Nurseries, tree lots, pot plants, home and landscaped gardens.

Performance Chart 360o Pattern

CFd® Downspray Range

Pressure (kPa)

Flow (lph)

Diameter (m)

50 100 150 50 100 150 50 100 150

16 22 27 20 29 35 24 34 41

0.6 0.6 0.5 0.6 0.5 0.5 0.6 0.5 0.5

0.8 mm Black 0.9 mm Brown 1.0 mm Blue

SPRAYS

Nozzle Size/Colour

Ordering Information - CFd® Downspray Nozzle Size & Colour 0.8 mm Black 0.9 mm Brown 1.0 mm Blue

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

19005 19025 19015

100 100 100

90 90 90

14.4 14.4 14.4

Ordering Information - CFd® Galvanised Wire Stake Assembly w/Shut-Off Clip Nozzle Size & Colour

Tube Length

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

914 mm 914 mm 914 mm

43705 43725 43715

25 25 25

12 12 12

9.6 9.6 9.6

0.8 mm Black 0.9 mm Brown 1.0 mm Blue

Ordering Information - CFd® Downspray Stake Assembly Nozzle Size & Colour

Tube Length

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

300 mm 914 mm

17515 17615

25 25

16 10

11.1 8.5

1.0 mm Blue 1.0 mm Blue

Specications Dimensions Assembled

CFd® Downspray Wire Stake Assembly with 914 mm Tube & Adaptor

HEIGHT WIDTH DEPTH WEIGHT (approx.)

FRAME STAKE ADAPTOR UV STABILISED OFF-TAKE TUBE MATERIALS BARB ADAPTOR STAKE

Cfd® Downspray Stake Assembly with 300 mm Tube BASE/CONNECTION TYPE: & Adaptor

Inlet

Cfd® Downspray 34 mm 25 mm 8 mm 1.4 g acetal

‘Quick’ THREAD with Sealing Barb 4 mm

CFd® Galvanised Wire Assembly

Cfd® Stake Assembly

345 mm 24 mm

360 mm 24 mm

26 g acetal polypropylene PEVA acetal galvanised steel

28 g acetal acetal PVC acetal polypropylene

BARB 4 mm

BARB 4 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

20

TM

Frame Jets

Low maintenance open spray jets which excel in performance and reliability. Deector snaps on to frame to temporarily restrict spray diameter for young trees.

Features Ÿ Open frame and spray plate. Ÿ No moving parts. Ÿ Choice of 7 spray patterns and 8 ow rates. Ÿ Colour coded nozzles for ow rate identication. Ÿ ‘Quick’ thread for easy insertion into tubing, Rigid Risers or micro stakes.

Applications Specically designed for orchards, vineyards and horticultural crops.

Accessories Rigid Riser and Micro Stake.

Ordering Information - Frame JetsTM Order Code

Pack Quantity

Packs per Carton

Carton (kg)

Page 22

50

120

12.7

Deector

12995

50

120

12.6

Micro Stake with 600 mm Tube & Adaptor

40705

25

5

6.7

Description

SPRAYS

Frame JetsTM

Specications Dimensions HEIGHT WIDTH LENGTH WEIGHT (approx.)

Frame JetTM 360o x 22 Pattern

UV Stabilised Material 32 mm FRAME 13 mm BASE 27 mm DEFLECTOR 1.8 g

acetal acetal Inlet acetal

Typical System

Micro Stake with 600 mm Tube and Adaptor

21

Deector for Frame JetTM

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Base/Connection Type

‘QUICK’ THREAD 4 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

1.55 mm Red

1.3 mm Green

1.23 mm Grey

1.1 mm Purple

1.0 mm Blue

0.9 mm Brown

0.85 mm Orange

0.8 mm Black

Nozzle Size & Base Colour

4.7

5.4

7.3

103

120

136

250

100

150

84

50

200

98

57

250

75

86

150

200

12155

12135

4.9

42

61

50

100

12.4

11.4

9.6

7.8

5.5

9.0

8.2

7.4

6.5

9.4

10.3

76

85

8.6

200

12145

8.6

5.2

250

53

100

7.3

8.0

65

50

12165

6.5

150

73

37

250

55

65

150

200

4.4

31

45

50

100

7.9

7.4

54

60

5.7

200

12115

7.0

4.0

250

37

100

5.6

6.1

46

50

12125

4.6

150

48

26

250

37

43

150

200

3.2

21

30

50

100

5.9

6.9

37

42

200

5.6

250

12175

3.6

5.9

5.2

4.5

3.8

3.0

High

32

26

12105

Order Code

9.3

8.2

6.9

6.0

4.3

7.8

7.0

6.4

5.3

3.8

8.5

7.7

6.8

5.9

4.1

6.8

6.1

5.4

4.7

3.4

6.3

6.7

4.7

4.7

3.0

6.0

5.0

4.4

3.6

2.6

5.5

5.0

4.5

3.9

2.8

4.6

4.3

3.8

3.0

2.3

Low

Diameter (m)

26o High 12.5o Low

150

100

37

18

250

50

29

33

150

200

16

23

50

Flow (lph)

100

Press (kPa)

Trajectory

A 360o x 12

12255

12235

12245

12265

12215

12225

12275

12205

Order Code

22o

12.3

11.2

10.0

8.6

6.4

10.8

9.5

8.6

7.1

5.4

10.1

9.5

8.6

7.6

5.5

9.9

9.2

7.9

7.1

5.3

8.6

8.3

6.7

6.0

4.4

8.1

7.4

6.8

6.1

4.2

7.6

6.8

6.0

5.4

4.1

7.2

6.5

6.0

5.0

3.6

Diameter (m)

B Buttery

12355

12335

12345

12365

12315

12325

12375

12305

Order Code

22o

11.0

9.8

8.9

7.8

5.6

10.2

9.1

8.2

7.2

5.2

10.4

9.4

8.3

7.4

5.4

9.0

8.6

7.5

6.5

4.7

7.9

7.5

6.8

6.0

4.3

6.7

6.1

5.6

4.9

3.6

7.0

6.5

5.9

5.3

3.9

6.7

6.4

6.1

5.2

3.7

Diameter (m)

C 210o x 8

12555

12535

12545

12565

12515

12525

12575

12505

Order Code

12.5o

8.2

7.6

6.6

5.7

4.3

7.3

6.6

5.9

5.0

3.8

6.8

6.4

5.6

5.1

3.7

6.3

5.7

5.0

4.4

3.5

5.5

5.0

4.4

3.8

3.1

4.6

4.2

3.8

3.5

2.6

4.7

4.3

3.8

3.4

2.6

3.8

3.4

3.2

3.0

2.3

Diameter (m)

E 360o x 22

12655

12635

12645

12665

12615

12625

12675

12605

Order Code

22o

4.9

4.4

4.8 5.5

4.8 5.7

5.5

6.5

5.6 6.5

6.4 7.4

6.1

7.0

9.1

10.0

7.1

8.7

8.1

6.1

7.2

9.5

7.4 4.2

8.1 5.0

6.7

7.6

12755

3.9 5.0

4.5 6.1

7.3 7.7

8.2 8.9

12735

6.9 4.2

7.4 4.8

6.4

6.9

12745

3.4 4.7

3.9 5.4

6.3 6.8

6.1 6.5

12765

6.3 3.5

5.3 3.8

6.0

4.9

12715

3.2 4.2

3.0 3.9

5.5 5.9

5.5 6.0

12725

4.3 5.1

4.3 5.0

5.8

5.1

4.4

3.9

2.8

High

7.2

6.5

5.9

4.9

3.7

5.7

5.3

4.8

4.1

3.1

5.0

4.7

4.2

3.7

2.5

4.3

3.8

3.5

2.7

2.2

3.8

3.5

3.2

2.8

2.3

3.1

2.9

2.7

2.4

1.8

3.7

3.4

3.0

2.6

2.0

2.0

2.0

1.7

1.5

1.4

Low

Diameter (m)

3.1

12775

12705

Order Code

12.5o

R Rectangular

3.2

5.0

4.8

4.2

3.7

2.9

Diameter (m)

J 360o x 12

SPRAYS

Pattern

12855

12835

12845

12865

12815

12825

12875

12805

Order Code

22o

12.0

10.9

9.7

8.2

6.0

10.3

9.3

8.5

7.2

5.2

10.0

9.1

8.4

6.8

5.0

9.1

8.4

7.4

6.4

4.8

7.5

6.8

6.1

5.5

3.9

6.6

6.1

5.4

4.6

3.6

6.5

6.1

5.4

4.5

3.4

6.1

5.5

5.1

4.4

3.2

Diameter (m)

V 300o x 10

Performance and Ordering Information

22

Rotor SprayTM Mini Sprinklers Durable and reliable with excellent distribution uniformity.

Vari-Rotor Spray™ can be adjusted to alter ow and coverage.

Features Ÿ C-Frame design for strength and high distribution uniformity. Ÿ Full ow ipper suspended between two bearings for reliable performance. Ÿ Inverted model incorporates special khaki coloured ipper with dust cover to protect bearing. Ÿ Colour coded nozzles to identify ow rates. ® Ÿ 4 mm thread for installing into Rigid Risers, Asta Stake Adaptor, Micro Stake and 1/2” micro threaded adaptors. Ÿ UV stabilised materials for long life.

Applications Landscape areas, home gardens, nurseries and horticultural applications.

Inverted Rotor Spray™ ideal for overhead greenhouse and nursery watering.

Ordering Information - Rotor SprayTM

SPRINKLERS

Nozzle Size & Colour 0.9 mm Brown 1.0 mm Blue 1.3 mm Green 1.5 mm Red 1.8 mm Orange 2.0 mm Grey

Base Type

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

4 mm 4 mm 4 mm 4 mm 4 mm 4 mm

20025 20015 20035 20055 20075 20045

50 50 50 50 50 50

110 110 110 110 110 110

12.5 12.5 12.5 12.5 12.5 12.5

Ordering Information - Inverted Rotor SprayTM Rotor SprayTM 4 mm Thread

Nozzle Size & Colour 0.9 mm Brown 1.0 mm Blue 1.3 mm Green 1.5 mm Red

Base Type

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

4 mm 4 mm 4 mm 4 mm

20125 20115 20135 20155

50 50 50 50

110 110 110 110

12.5 12.5 12.5 12.5

Base Type

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

4 mm 4 mm

20295 20205

25 25

88 88

9.6 9.6

Ordering Information - Vari-Rotor SprayTM Nozzle Size & Colour 1.5 mm Yellow 1.5 mm Black

Ordering Information - Rotor SprayTM Stake Assembly w/ 300 mm Tube & Barb Adaptor Nozzle Size & Colour Inverted Rotor SprayTM 4 mm Thread

1.3 mm Green

Base Type

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

4 mm

17245

25

13

14.0

Ordering Information - Vari-Rotor SprayTM Stake Assembly w/ 300 mm Tube & Barb Adaptor Nozzle Size & Colour 1.5 mm Black

Base Type

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

4 mm

17295

25

13

10.0

Specications Dimensions Assembled

Vari-Rotor SprayTM 4 mm Thread

HEIGHT WIDTH WEIGHT (approx.)

FRAME UV BASE STABILISED FLIPPER MATERIALS KNOB BASE/CONNECTION TYPE:

23

Inlet

Rotor SprayTM and Inverted Rotor SprayTM

Vari-Rotor SprayTM

35 mm 27 mm 2.0 g acetal acetal nylon -

45 mm 27 mm 3.5 g acetal acetal nylon HDPE

10-32 UNF THREAD 4 mm

10-32 UNF THREAD 4 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Rotor SprayTM Mini Sprinklers Performance Chart - Rotor SprayTM & Inverted Rotor SprayTM Type Nozzle Size & Colour 0.9 mm Brown 1.0 mm Blue 1.3 mm Green 1.5 mm Red

2.0 mm Grey

Inverted Rotor SprayTM

Tested 0.2 m above ground

Tested 0.8 m Tested 2.0 m above ground above ground

Pressure (kPa)

Flow (lph)

Diameter (m)

Stream Height (m)

Diameter (m)

Diameter (m)

100

31

5.2

0.2

4.0

5.4

125

35

5.6

0.3

4.2

5.8

150

38

5.6

0.4

4.2

6.0

100

38

5.2

0.3

4.2

5.6

125

42

5.4

0.4

4.4

5.8

150

46

5.4

0.5

4.6

6.0

100

61

6.0

0.4

4.2

5.8

150

76

6.9

0.5

4.6

6.2

200

88

7.2

0.5

5.0

6.6

100

85

6.5

0.4

4.4

6.2

150

105

7.5

0.4

4.8

6.4

200

120

8.1

0.4

5.0

7.2

100

95

6.7

0.3

150

117

7.5

0.4

200

135

8.4

0.5

100

120

6.8

0.4

150

150

7.8

0.4

200

175

8.0

0.5

SPRINKLERS

1.8 mm Orange

Rotor SprayTM

Performance Chart - Vari-Rotor SprayTM Vari-Rotor SprayTM Type Nozzle Size & Colour 1.5 mm Yellow TM

Rotor Spray Stake Assembly with 300 mm Tube and Adaptor

1.5 mm Black

Pressure (kPa)

Tested 0.2 m above ground Flow (lph)

Diameter (m)

Stream Height (m)

100

0 - 82

0 - 6.5

0 - 0.4

150

0 - 105

0 - 7.5

0 - 0.4

200

0 - 123

0 - 8.1

0 - 0.4

100

0 - 82

0 - 6.5

0 - 0.4

150

0 - 105

0 - 7.5

0 - 0.4

200

0 - 123

0 - 8.1

0 - 0.4

Vari-Rotor SprayTM Stake Assembly with 300 mm Tube and Adaptor Antelco irrigation equipment metric catalogue 2020 www.antelco.com

24

®

Rotor Rain Mini Sprinklers Low trajectory, large droplet mini sprinkler.

Features Ÿ C-Frame design for strength and high distribution uniformity. Ÿ Full ow ipper suspended between two bearings for reliable performance. Ÿ Colour coded nozzles to identify ow rates. Ÿ Range extended to include three new low ow nozzle sizes. Ÿ Break-off spray deector for close-in watering of immature trees.

Applications Vines, row and tree crops such as nuts, citrus and apples.

Accessories Rotor Stakes and adaptors.

Ordering Information - Rotor Rain® 3/8" Male Thread

SPRINKLERS

Nozzle Size & Colour

Rotor Rain® 3/8" Male Thread

0.9 mm Black 1.0 mm White 1.2 mm Brown 1.5 mm Green 1.7 mm Blue 1.9 mm Grey 2.0 mm Yellow 2.1 mm Olive 2.4 mm Red 2.6 mm Orange 2.8 mm Purple

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

20625 20635 20645 20335 20315 20345 20395 20385 20355 20375 20365

50 50 50 50 50 50 50 50 50 50 50

28 28 28 28 28 28 28 28 28 28 28

11.8 11.8 11.8 11.8 11.8 11.8 11.8 11.8 11.8 11.8 11.8

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

20655 20665 20675 20535 20515 20545 20595 20585 20555 20575 20565

50 50 50 50 50 50 50 50 50 50 50

20 20 20 20 20 20 20 20 20 20 20

11.4 11.4 11.4 11.4 11.4 11.4 11.4 11.4 11.4 11.4 11.4

Ordering Information - Rotor Rain® 1/2" Male Thread Nozzle Size & Colour

Rotor Rain® 1/2" Male Thread

0.9 mm Black 1.0 mm White 1.2 mm Brown 1.5 mm Green 1.7 mm Blue 1.9 mm Grey 2.0 mm Yellow 2.1 mm Olive 2.4 mm Red 2.6 mm Orange 2.8 mm Purple

Specications Dimensions Assembled HEIGHT WIDTH WEIGHT (approx.)

FRAME UV STABILISED FLIPPER MATERIALS NOZZLE BASE/CONNECTION TYPE:

25

Inlet

Rotor Rain® 3/8"

Rotor Rain® 1/2"

49 mm 46 mm 8g acetal nylon acetal

49 mm 46 mm 10.5 g acetal nylon acetal

THREAD 3/8" BSPM

THREAD 1/2" MNPT

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

®

Rotor Rain Mini Sprinklers Performance Chart - Rotor Rain® Nozzle Size & Colour

NEW

0.9 mm Black

1.0 mm White

1.2 mm Brown

1.5 mm Green

1.9 mm Grey

2.0 mm Yellow

2.1 mm Olive

Rotor Stake Range 5mm CODE: 40555 10mm CODE: 40515 13mm CODE: 40535

2.4 mm Red

*Refer to page 52 for stake information

2.6 mm Orange

2.8 mm Purple

NEW

Flow (lph)

100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250

30 37 43 48 35 43 50 57 54 66 77 86 77 94 110 120 100 125 145 163 125 153 178 200 147 183 215 240 168 205 235 265 195 240 280 315 245 300 350 395 265 330 385 430

Diameter (m)

Stream Height (m)

3.5 3.9 4.1 4.3 4.4 5.5 6.1 6.3 4.5 5.6 6.2 6.3 7.8 8.7 9.1 8.5 8.6 9.3 9.6 9.3 8.9 10.2 9.8 10.0 10.0 11.0 11.2 11.0 10.7 11.6 11.8 11.4 11.0 12.5 12.5 12.1 10.9 11.9 12.1 12.0 11.2 12.8 13.0 12.4

0.3 0.3 0.3 0.4 0.4 0.4 0.4 0.5 0.4 0.4 0.4 0.4 0.5 0.5 0.6 0.7 0.7 0.7 0.8 0.9 0.7 0.8 0.8 0.9 0.6 0.8 0.9 1.0 0.7 0.8 0.9 0.9 0.6 0.9 1.0 1.0 0.7 0.8 0.9 1.0 0.8 0.9 1.0 1.1

Deector Diameter (m) 2.2

2.5

2.2

2.8

2.8

2.8

3.0

SPRINKLERS

1.7 mm Blue

Tested at 0.2 m above ground Pressure (kPa)

3.0

3.2

3.2

4.0

Ordering Information - Rotor Rain® Assembled on Stake w/ 600 mm Tube & Adaptor Nozzle Size & Colour 0.9 mm Black 1.0 mm White 1.2 mm Brown 1.5 mm Green

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

43805 43885 43825 43835

10 10 10 10

10 10 10 10

7.0 7.0 7.0 7.0

Rotor Rain® Assembled on Stake with 600 mm Tube & Adaptor Antelco irrigation equipment metric catalogue 2020 www.antelco.com

26

®

Rotor Rain Plus Mini Sprinkler Introducing a new high performance and featured range of mini sprinklers, the Rotor Rain® Plus incorporates the following: Features Ÿ Anti-insect spinner design. Ÿ Proled double frame to maximize water distribution. Ÿ Easily identiable wide range of colour coded ow rates. Ÿ Ease of eld disassembly. Ÿ Long eld life bearing and spinner. Ÿ Standard or Deector spinner for young trees. Ÿ Suspension hole for trellis applications. Ÿ Available in 3/8" or 1/2" male threaded inlets.

Applications Orchards, row crops and smaller vegetable plots.

SPRINKLERS

Ordering Information - Rotor Rain® Plus 3/8" Male Thread Nozzle Size & Colour

NEW Rotor Rain® Plus with Deector 3/8" Male Thread

0.8 mm Brown 0.9 mm Blue 1.1 mm Grey 1.2 mm Black 1.4 mm Orange 1.6 mm Red 1.8 mm Light Blue 2.0 mm Yellow 2.3 mm Purple 2.5 mm Olive

Order Code Standard Spinner

Order Code w/Deector Spinner

22015 22025 22035 22045 22055 22065 22075 22085 22095 22105

22115 22125 22135 22145 22155 22165 -

Pack Packs per Carton (kg) Quantity Carton 50 50 50 50 50 50 50 50 50 50

20 20 20 20 20 20 20 20 20 20

11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7

Ordering Information - Rotor Rain® Plus 1/2" Male Thread Nozzle Size & Colour

NEW

1.4 mm Orange 1.6 mm Red 1.8 mm Light Blue 2.0 mm Yellow 2.3 mm Purple 2.5 mm Olive

Order Code Standard Spinner

Order Code w/Deector Spinner

22335 22345 22355 22365 22375 22385

22395 22405 -

Pack Packs per Carton Quantity Carton (kg) 50 50 50 50 50 50

18 18 18 18 18 18

12.3 12.3 12.3 12.3 12.3 12.3

Rotor Rain® Plus 1/2" Male Thread

Specications Dimensions Assembled HEIGHT WIDTH DEPTH WEIGHT (approx.)

FRAME UV STABILISED SPINNER MATERIALS NOZZLE Easy turn eld disassembly

27

BASE/CONNECTION TYPE:

Inlet

Rotor Rain® Plus 3/8"

Rotor Rain® Plus 1/2"

53 mm 46 mm 21 mm 11.0 g acetal nylon acetal

58 mm 46 mm 21 mm 12.1 g acetal nylon acetal

THREAD 3/8" BSPM

THREAD 1/2" MNPT

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

®

Rotor Rain Plus Mini Sprinkler Performance Chart - Rotor Rain® Plus Nozzle Size & Colour

NEW

0.8 mm Brown

0.9 mm Blue

1.1 mm Grey

1.2 mm Black

1.6 mm Red

1.8 mm Light Blue

Rotor Stake Range

2.0 mm Yellow

5mm CODE: 40555 10mm CODE: 40515 13mm CODE: 40535

2.3 mm Purple

*Refer to page 52 for stake information

2.5 mm Olive

Flow (lph)

100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250 100 150 200 250

22 27 32 35 28 35 41 46 44 54 62 69 52 65 75 84 70 87 101 113 94 116 136 151 121 149 173 194 149 184 213 239 199 247 288 323 239 291 338 379

Diameter (m)

Stream Height (m)

3.6 4.6 5.1 5.4 4.9 5.7 5.9 6.0 4.8 5.5 5.9 6.2 5.7 6.0 6.1 6.1 6.0 6.2 6.4 6.5 6.5 7.0 7.4 7.7 6.8 7.8 8.1 8.2 8.5 9.9 10.5 10.8 8.9 9.9 10.2 10.3 9.2 10.5 10.9 10.8

0.3 0.4 0.4 0.4 0.4 0.5 0.5 0.6 0.3 0.3 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.5 0.5 0.4 0.4 0.5 0.4 0.5 0.5 0.5 0.6 0.9 0.9 1.0 1.0 0.7 0.7 0.8 0.8 0.6 0.8 0.8 0.7

Deector Diameter (m) 1.6

1.6

1.7

2.2

2.1

1.9

N/A

SPRINKLERS

1.4 mm Orange

Tested at 0.2 m above ground Pressure (kPa)

N/A

N/A

N/A

Recommended riser tubing sizes

NEW

Install on 5 mm Micro tubing 0.8 mm Brown

0.9 mm Blue

1.1 mm Grey

1.2 mm Black

Install on 10 mm or 13 mm tubing 1.4 mm Orange

1.6 mm Red

1.8 mm Lt. Blue

2.0 mm Yellow

2.3 mm Purple

2.5 mm Olive

Ordering Information - Rotor Rain® Plus Assembled on Stake w/ 600 mm Tube & Adaptor Nozzle Size & Colour 0.8 mm Brown - Standard Spinner 0.9 mm Blue - Standard Spinner 1.1 mm Grey - Standard Spinner 1.2 mm Black - Standard Spinner 1.4 mm Orange - Standard Spinner 0.8 mm Brown w/ Deector Spinner 0.9 mm Blue w/ Deector Spinner 1.1 mm Grey w/ Deector Spinner 1.2 mm Black w/ Deector Spinner 1.4 mm Orange w/ Deector Spinner

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

22175 22185 22195 22205 22215 22275 22285 22295 22305 22315

10 10 10 10 10 10 10 10 10 10

8 8 8 8 8 8 8 8 8 8

5.3 5.3 5.3 5.3 5.3 5.7 5.7 5.7 5.7 5.7

Rotor Rain® Plus Assembled on Stake with 600 mm Tube & Adaptor Antelco irrigation equipment metric catalogue 2020 www.antelco.com

28

TM

Rotor Max Midi Sprinklers Robust and reliable “spinner” sprinkler for use above and below plant foliage and with two trajectory options. Excellent sprinkler distribution patterns and performance.

Features Dual outlet spinner enhances performance.

Standard model has a 25° trajectory with black coloured spinner.

Inverted model has a 0° at trajectory with khaki coloured spinner.

Range includes two low ow nozzle sizes (2.0 mm & 2.4 mm).

Easily taken apart for servicing.

UV stabilised materials for long life.

Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ

Applications Greenhouses, vegetable row crops and under tree watering.

Inverted Rotor Max™ is ideal for over-head watering in glasshouse, nursery and shade house applications. The 0° trajectory also suited to upright operation, excellent for under foliage or wind affected locations.

Performance Chart 25o

SPRINKLERS

25o

Nozzle Size & Colour

Upright - 25o on 0.2 m Riser Pressure (kPa)

Flow (lph)

100 150 200 250 300 100 150 200 250 300 100 150 200 250 300 100 150 200 250 300 100 150 200 250 300

145 175 205 230 255 215 275 315 345 375 300 355 400 460 500 375 460 540 600 660 550 665 775 875 975

2.0 mm Yellow

2.4 mm Green

Upright - 25o Trajectory (Black Spinner)

0o

0o

2.8 mm Red

3.2 mm Black

Upright - 0o Trajectory (Khaki Spinner)

3.8 mm Purple

Inverted - 0o on 2 m Riser

Diameter (m)

Stream Height (m)

Diameter (m)

6.8 8.0 9.0 9.4 9.8 7.6 9.0 10.0 10.2 10.4 11.0 12.0 13.0 13.0 13.0 11.0 12.0 13.0 13.0 14.0 11.9 12.5 13.8 14.0 13.4

0.7 1.0 1.1 1.1 1.2 0.7 1.0 1.1 1.1 1.2 0.9 1.0 1.2 1.2 1.4 0.9 1.0 1.2 1.2 1.3 0.7 0.9 1.0 1.1 1.2

7.2 8.2 9.2 9.4 9.6 8.4 9.2 9.8 10.2 10.0 11.0 12.0 13.0 13.0 13.0 11.0 12.0 13.0 13.0 14.0 11.9 12.5 13.8 14.0 13.4

Ordering Information - Rotor MaxTM 3/8" Male Thread Nozzle Size & Colour 0o

0o

Inverted - 0o Trajectory (Khaki Spinner)

NEW

Rotor MaxTM 3/8" Stake Range 10mm CODE: 40515 13mm CODE: 40535 *Refer to page 52 for stake information

29

2.0 mm Yellow 2.4 mm Green 2.8 mm Red 3.2 mm Black 3.8 mm Purple

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

21175 21185 21155 21105 21165

20 20 20 20 20

10 10 10 10 10

8.0 8.0 8.0 8.0 8.0

Pack Quantity

Packs per Carton

Carton (kg)

20 20 20 20 20

10 10 10 10 10

8.2 8.2 8.2 8.2 8.2

Ordering Information - Rotor MaxTM 1/2" Male Thread Nozzle Size & Colour 2.0 mm Yellow 2.4 mm Green 2.8 mm Red 3.2 mm Black 3.8 mm Purple

Order Code Order Code Inverted Upright Khaki 0º Black 25º 21075 21085 21055 21005 21065

21585 21595 21555 21505 21565

Specications Dimensions Assembled UV Stabilised Material Base/Connection Type HEIGHT 96 mm FRAME polypropylene Inlet THREAD 3/8" BSPM WIDTH 90 mm SPINNER acetal Inlet THREAD 1/2" BSPM WEIGHT (approx.)

38 g NOZZLE acetal Antelco irrigation equipment metric catalogue 2020 www.antelco.com

TM

Rotor Max Deector New eld snap-on 180o Deector provides part circle operation for road edges, driveways and end of sprinkler rows.

Features Ÿ Easy snap-on eld tted Deector. o Ÿ Directional ribs distribute the water evenly over the 180 pattern. Ÿ Water is redirected by the cupped spray plate providing improved application uniformity over at plate deectors.

Applications Part circle applications such as road edges, driveways and end of sprinkler rows.

Ordering Information - Rotor MaxTM 180o Deector

o

Deector 180

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

21365

10

28

4.8

NEW

SPRINKLERS

Nozzle Size & Colour

180o Deector

180o Deector tted

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

30

ReuZit® Recycled Water Products ReuZit® range of products specically designed for domestic and small commercial Aerobic Treatment Systems (ATS).

Features Ÿ Low operating pressure range ideal for recycled water sump pumps. Ÿ Robust stake with push point for inserting into soil. Ÿ Bubbler Assembly with 2.3 mm diameter nozzle size to reduce clogging. Ÿ Spray Assembly with 2.8 mm diameter nozzle size to reduce clogging. Ÿ 400 mm exible off-take tubing with easy insert hypodermic adaptor. Ÿ Purple coloured components for easy identication of recycled water.

Applications Distribution of aerobically treated water under trees, shrubs and ground covers in mulched areas.

RECYCLED WATER

Performance Pressure (kPa)

ReuZit® Bubbler Assembly

ReuZit® Spray Assembly

Tested at 0.2 m above ground

Tested at 0.2 m above ground

Flow (lph)

Diameter (m)

Flow (lph)

Diameter (m)

73 85 97 107 117 124 133 141

0.6 0.7 0.8 0.9 1.0 1.0 1.1 1.1

150 170 195 215 230 245 260 270

1.3 1.4 1.7 2.2 2.6 2.6 2.6 2.6

30 40 50 60 70 80 90 100

Ordering Information - ReuZit® Bubbler Assembly w/ Stake, 400 mm Tube & Adaptor Type ReuZit® Bubbler Assembly with Stake, 400 mm Tube & Adaptor

ReuZit® Bubbler Assembly

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

42005

10

15

7.3

Ordering Information - ReuZit® Spray Assembly w/ Stake, 400 mm Tube & Adaptor Type ReuZit® Spray Assembly

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

40595

10

10

5.4

Specications Dimensions Assembled

ReuZit® Spray Assembly Stake, 400 mm Tube & Adaptor

HEIGHT WIDTH DEPTH WEIGHT (approx.)

FRAME NOZZLE DEFLECTOR UV STABILISED SPRINKLER ADAPTOR MATERIAL STAKE TUBE ADAPTOR BASE/CONNECTION TYPE:

31

Inlet

Bubbler Assembly

Spray Assembly

343 mm 52 mm 28 mm 46 g acetal acetal acetal polypropylene PVC acetal

364 mm 51 mm 28 mm 53 g acetal acetal acetal polypropylene polypropylene PVC acetal

BARB 4 mm

BARB 4 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

ReuZit® Recycled Water Products ReuZit® range of products specically designed for domestic and small commercial Aerobic Treatment Systems (ATS).

Features Ÿ Low operating pressure range ideal for recycled water sump pumps. Ÿ Robust stake with hammer point for inserting into soil. Ÿ Large 3.8 mm diameter nozzle size to reduce risk of clogging. Ÿ 13 mm barbed take-off to suit low density poly tubing. Ÿ Purple coloured components for easy identication of recycled water.

Applications Localised watering of trees and shrubs on mulched areas.

Performance Chart

RECYCLED WATER

ReuZit® Sprinkler Pressure (kPa)

Tested at 0.2 m above ground

30 40 50 60 70 80 90 100

Flow (lph)

Diameter (m)

275 335 380 420 455 490 520 550

2.6 3.1 3.4 3.9 4.3 4.5 4.6 4.7

Ordering Information - ReuZit® Sprinkler Type Sprinkler Assembly with Stake 13 mm Inlet Sprinkler 1/2" BSPM Rotor Max Deector

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

40585 21575 21365

10 10 10

8 20 28

5.4 6.4 4.8

Specications Dimensions Assembled

ReuZit® Sprinkler Assembly with Stake 13 mm inlet

HEIGHT WIDTH DEPTH WEIGHT (approx.)

FRAME NOZZLE UV STABILISED SPINNER MATERIALS STAKE ADAPTOR BASE/CONNECTION TYPE:

Sprinkler Assembly

Sprinkler 1/2" BSPM

407 mm 90 mm 31 mm 59 g polypropylene acetal acetal polypropylene polypropylene BARB 13 mm

96 mm 90 mm 38 g polypropylene acetal acetal THREAD 1/2" BSPM

Inlet

Typical Aerobic Treatment System Purpleback Valve

ReuZit Bubbler

Indexing Valve (if required) ReuZit Spray Ground Level

ReuZit Sprinkler Stake

25 m

m

Waste Water In

c

Lila Po

ReuZit Sprinkler

ly

Float Switch

Purpleback Valve

ReuZit® Sprinkler 1/2" BSPM Pump

Treatment Tank

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

32

Valves On/off device to control the water ow in low pressure irrigation systems.

Features Ÿ Simple on/off operation and straight through ow. Ÿ Operating pressure range up to 300 kPa. ® Ÿ Green Back cap for standard irrigation applications. ® Ÿ Purple Back cap for recycled water applications. Ÿ UV stabilised materials for long life.

Applications Secondary zone water diversion and ow control. Always install as an In-Line valve with tubes connected to both inlet and outlet.

Ordering Information - Green Back® Valves Order Code

Pack Quantity

Packs per Carton

Carton (kg)

45505 45575 45555 45515 45565 45525 45535 45545

20 20 20 20 20 20 20 20

25 25 25 24 10 10 10 4

9.4 9.7 9.5 9.9 10.2 10.3 10.5 7.1

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

46505 46575 46555 46515 46565 46525 46535 46545

20 20 20 20 20 20 20 20

25 25 25 24 10 10 10 4

9.4 9.7 9.5 9.9 10.2 10.3 10.5 7.1

VALVES

Type

Green Back® Valve

Green Back® Green Back® Green Back® Green Back® Green Back® Green Back® Green Back® Green Back®

Valve 13 mm (Shank OD 12.6 mm) Valve 14 mm (Shank OD 14.0 mm) Valve 15 mm (Shank OD 14.6 mm) Valve 16 mm (Shank OD 15.7 mm) Valve 18 mm (Shank OD 17.6 mm) Valve 19 mm (Shank OD 19.0 mm) Valve 21 mm (Shank OD 20.8 mm) Valve 25 mm (Shank OD 25.0 mm)

Ordering Information - Purple Back® Valves Type

Purple Back® Valve

Purple Back® Purple Back® Purple Back® Purple Back® Purple Back® Purple Back® Purple Back® Purple Back®

Valve 13 mm (Shank OD 12.6 mm) Valve 14 mm (Shank OD 14.0 mm) Valve 15 mm (Shank OD 14.6 mm) Valve 16 mm (Shank OD 15.7 mm) Valve 18 mm (Shank OD 17.6 mm) Valve 19 mm (Shank OD 19.0 mm) Valve 21 mm (Shank OD 20.8 mm) Valve 25 mm (Shank OD 25.0 mm)

Specications - Green Back® and Purple Back® Valves

HEIGHT LENGTH WIDTH WEIGHT (approx.)

13 mm, 14 mm 15 mm, 16 mm 40 mm 81 mm 28 mm 18 g

BODY STEM COVER SEAL BASE/CONNECTION TYPE

acetal polypropylene acetal BARB

Dimensions Assembled

UV STABILISED MATERIALS

18 mm, 19 mm, 21 mm

25 mm

60 mm 100 mm 41 mm 49 g (18,19 mm) 50 g (21 mm) acetal polypropylene acetal silicone rubber BARB

71 mm 124 mm 53 mm 81 g

Specications - Threaded Valves 1/2" & 3/4"

acetal polypropylene acetal BARB

(refer page 34) 3/4" BSPM

Dimensions Assembled HEIGHT LENGTH WIDTH WEIGHT (approx.)

UV STABILISED MATERIAL

BODY STEM COVER SEAL BASE/CONNECTION TYPE

33

1/2" MNPT 41 mm 81 mm 28 mm 21 g acetal polypropylene acetal 1/2" MNPT x Barb

13 mm, 14 mm, 15 mm, 16 mm 44 mm 81 mm 28 mm 22 g

18 mm, 19 mm, 21 mm

60 mm 103 mm 41 mm 53 g (18,19 mm) 54 g (21 mm) acetal acetal polypropylene polypropylene acetal acetal silicone rubber 3/4" BSPM x Barb

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Valves Threaded ow control valves for low pressure irrigation.

Features Ÿ 3/4” threaded inlet or 1/2” threaded inlet. Ÿ Simple on/off operation and straight through ow. Ÿ Operating pressure range up to 300 kPa. ® Ÿ Green Back cap for standard irrigation applications. ® Ÿ Purple Back cap for recycled water applications. Ÿ UV stabilised materials for long life.

Applications Irrigation from rain tanks, non-pressurised containers or where 1/2” or 3/4” threaded connection is required.

Ordering Information - Threaded Green Back® Valve 1/2" Male Thread Type

Pack Quantity

Packs per Carton

Carton (kg)

49005 49015 49025 49035

20 20 20 20

22 22 22 22

9.8 9.9 9.8 10.3

VALVES

Threaded Green Back® Valve 1/2" Male Thread

Green Back® Valve 13mm Barb x 1/2" Green Back® Valve 14mm Barb x 1/2" Green Back® Valve 15mm Barb x 1/2" Green Back® Valve 16mm Barb x 1/2"

Order Code

Ordering Information - Threaded Purple Back® Valve 1/2" Male Thread Type

Threaded Purple Back® Valve 1/2" Male Thread

Purple Back® Valve 13 mm Barb x 1/2" Purple Back® Valve 14 mm Barb x 1/2" Purple Back® Valve 15 mm Barb x 1/2" Purple Back® Valve 16 mm Barb x 1/2"

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

49105 49115 49125 49135

20 20 20 20

22 22 22 22

9.8 9.9 9.8 10.3

Ordering Information - Threaded Green Back® Valve 3/4" Male Thread Type

Threaded Green Back® Valve 3/4" Male Thread

Green Back® Valve 13 mm Barb x 3/4" Green Back® Valve 14 mm Barb x 3/4" Green Back® Valve 16 mm Barb x 3/4" Green Back® Valve 18 mm Barb x 3/4" Green Back® Valve 19 mm Barb x 3/4" Green Back® Valve 21 mm Barb x 3/4"

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

46605 46675 46615 46685 46695 46595

20 20 20 20 20 20

22 22 21 9 9 9

10.4 10.6 10.9 10.2 10.2 10.3

Ordering Information - Threaded Purple Back® Valve 3/4" Male Thread Type

Threaded Purple Back® Valve 3/4" Male Thread

Purple Back® Valve 13 mm Barb x 3/4" Purple Back® Valve 14 mm Barb x 3/4" Purple Back® Valve 16 mm Barb x 3/4" Purple Back® Valve 18 mm Barb x 3/4" Purple Back® Valve 19 mm Barb x 3/4" Purple Back® Valve 21 mm Barb x 3/4"

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

46705 46775 46715 46785 46795 46805

20 20 20 20 20 20

22 22 21 9 9 9

10.4 10.6 10.9 10.2 10.2 10.3

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

34

eZyvalveTM4 A compact valve box with 4 internal solenoid valves available in models to suit either 24 Vac or 9 Vdc latching irrigation controller. The eZyvalve™4 provides a trouble-free way to distribute water to a micro irrigation-system.

Features Ÿ Pre-assembled with no internal pipe connections. Ÿ High strength UV stabilised materials. Ÿ Includes cable seal and wire connectors. Ÿ Water, dust and pest resistant. Ÿ Textured non-slip lid with o-ring seal and stainless steel screws. Ÿ 3/4” threaded inlet and outlet connections. Ÿ Easy to connect to existing garden taps using Braided Hose accessory.

Applications Landscape, home gardens, greenhouses and nurseries. Above and below ground installation.

VALVES

Performance Chart Flow Rate (lpm)

Pressure Loss (kPa)

10 15 20 25 30

30 63 108 165 231

Ordering Information - eZyvalve™4

eZyvalve™4 - 24 Vac

Type eZyvalve™4 - 24 Vac Solenoids 3/4" eZyvalve™4 - 9 Vdc Latching Solenoids 3/4"

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

16605 16625

1 1

10 10

11.5 12.9

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

90603 45825

1 25

40 30

16.1 12.1

Ordering Information - Accessories Type Braided Hose 1000 mm x 3/4" BSPF Tap Adaptor 1" BSPF x 3/4" BSPM eZyvalve™4 - 9 Vdc Latching

Braided Hose

Specications Dimensions Packaged LENGTH DEPTH WIDTH WEIGHT (approx.) - 24 Vac WEIGHT (approx.) - 9 Vdc Latching

Connection Type 105 mm 182 mm Inlet 182 mm Outlet 1075 g 1150 g

3/4" BSPM tapered 3/4" BSPM parallel x 4

Operating Specications FLOW RANGE PRESSURE RANGE - 24 Vac PRESSURE RANGE - 9 Vdc AMBIENT TEMPERATURE ELECTRICAL - 24 Vac ELECTRICAL - 9 Vdc Latch

35

1 lpm -30 lpm 20 kPa - 1250 kPa 20 kPa - 750 kPa 2o C - 60o C 24 Vac, inrush current 320 mA, holding current 260 mA at 50 Hz 9 Vdc, inrush current 1200 mA

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Pressure Regulators Designed for low-ow micro irrigation systems. Pressure Regulators stabilise the outlet pressure, optimising dripper and spray performance.

Features Ÿ Inlet pressure range: 0 - 700 kPa. Ÿ Operating ow: 0.4 - 30 lpm. Ÿ Two outlet pressure options: 100 kPa or 175 kPa. Ÿ 3/4” BSPF inlet x 3/4” BSPM outlet. Ÿ High strength, chemically resistant ABS construction for durability.

Applications Drip, spray and sprinkler systems in landscape applications. Ideally connected to taps, valves, tap timers and irrigation valves in a manifold system.

Ordering Information - Pressure Regulators Type

Pack Quantity

Packs per Carton

Carton (kg)

49505 49535

10 10

42 42

14.5 14.5

Performance Chart - 100 kPa Outlet Pressure (kPa)

160 4 lpm

140

15 lpm 120

30 lpm

100

80 100

Pressure Regulator 100 kPa

VALVES

3/4" BSPF Inlet x 3/4" BSPM Outlet - 100 kPa 3/4" BSPF Inlet x 3/4" BSPM Outlet - 175 kPa

Order Code

200

300

400 Inlet Pressure (kPa)

500

600

700

Performance Chart - 175 kPa 220 4 lpm 15 lpm

Outlet Pressure (kPa)

200 180

30 lpm

160 140 120 100

100

200

300

400 Inlet Pressure (kPa)

500

600

700

Specications Dimensions

Pressure Regulator 175 kPa

Operation

LENGTH 68 mm OUTLET PRESSURE WIDTH 34 mm FLOW RANGE WEIGHT (approx.)

31 g

Connection Type

100 kPa or 175 kPa Inlet 0.4 - 30 lpm Outlet

3/4" BSPF 3/4" BSPM

The Pressure Regulators must always be installed downstream from all shut-off valves, regardless of the application. Ÿ Regulators should be installed with the vent hole unobstructed. Ÿ Do not use sealing compound (solvent cement). If needed, tef lon tape may be used to seal for leaks. Ÿ

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

36

Micro Fittings A range of ttings and adaptors to use with quality micro tubing in low pressure irrigation systems. A range of sizes suit various tube congurations.

Features Ÿ Single barb congurations for connecting to micro or supply tube. Ÿ "Quick" thread or 4 mm thread for connecting to Rigid Risers or Micro Stakes. Ÿ A range of adaptors to suit various congurations.

Applications Home gardens, landscaping and glasshouses.

Ordering Information - Adaptors

FITTINGS

Type Adaptor 4 mm (F) x 1/2" Female Thread Adaptor 4 mm (F) x 1/2" Male Thread Adaptor 4 mm (F) x 3/8" BSWM Thread Adaptor 4 mm ‘Quick’ Thread x Thread Adaptor 4 mm Barb x Thread Adaptor 4.5 mm Barb x Thread

Adaptor 4 mm (F) x 1/2" Female Thread

Adaptor 4 mm (F) x 1/2" Male Thread

Joiner 4 mm Barb Joiner 4.5 mm Barb Joiner 4 mm Barb x Barb Hypodermic

Adaptor ‘Quick’ Thread x Thread

Packs per Carton

Carton (kg)

41015 41075 41025 40925 40945 40995

25 25 100 100 100 100

80 90 130 260 280 250

7.6 7.3 10.6 14.4 15.6 15.3

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

40145 40195 40935

100 100 100

245 240 245

14.0 17.0 14.0

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

40245 40295

50 50

490 490

14.0 13.5

45345

Pack Quantity 50

Packs per Carton 120

Carton (kg) 10.2

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

40345 40395

50 50

315 300

11.8 13.0

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

40445 40495

50 50

240 220

11.1 12.1

Ordering Information - Elbows Type

Adaptor Barb x Thread

Pack Quantity

Ordering Information - Joiners Type

Adaptor 4 mm (F) x 3/8" BSWM Thread

Order Code

Elbow 4 mm Barb Elbow 4.5 mm Barb Joiner Barb x Barb

Ordering Information - Elbow Clip On Accessories Type

Joiner Barb x Barb Hypodermic

Tidy-BowTM Clip On Elbow

Order Code

Ordering Information - Tees Elbow

Type Tee 4 mm Barb Tee 4.5 mm Barb

Tidy-BowTM Clip On Elbow

Ordering Information - Crosses Type Tee

Cross 4 mm Barb Cross 4.5 mm Barb

Cross

37

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Micro Fittings A range of repair plugs, valves and micro tube tee to use with quality micro tubing in low pressure irrigation systems. A range of sizes suit various tube congurations.

Features Ÿ Goof Plugs to repair wrongly punched holes. Ÿ Vari-Flow™ valves simple on/off operation controls water ow in micro irrigation systems. Ÿ Micro tee connects micro tube to lateral line.

Applications Home gardens, landscaping and glasshouses.

Ordering Information - Goof (Repair) Plugs Pack Quantity

Packs per Carton

Carton (kg)

42325

10

250

7.2

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

42155 42115 42125

50 50 50

90 90 90

11.5 11.5 11.5

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

47765 47465

25 25

56 48

10.1 9.4

Goof (Repair) Plugs - Rack of 10

Goof (Repair) Plugs

FITTINGS

Order Code

Type

Ordering Information - Vari-FlowTM Valve Colour

Type Vari-FlowTM Barb x Barb

Vari-FlowTM Valve barb 4.5 mm Vari-FlowTM Valve thread 4.0 mm Vari-FlowTM Valve thread 4.0 mm

Black Black Green/Yellow

Vari-FlowTM Thread x Thread

Ordering Information - Reducing Tee Type 13 mm line x 4 mm branch 14 mm (16 O.D. Dripline) x 4 mm branch

Micro Tee

Specications - Vari-FlowTM Valve Dimensions Assembled HEIGHT LENGTH WIDTH WEIGHT (approx.)

UV STABILISED MATERIALS

BODY KNOB

BASE/CONNECTION TYPE

4.5 mm Barb

4.0 mm Thread

21 mm 40 mm 15 mm 2.5 g acetal HDPE

21 mm 40 mm 15 mm 2.5 g acetal HDPE

Barb 4.5 mm

10-32 UNF Thread 4 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

38

Take-Off Fittings Antelco Take-Off ttings provide an easy to install method of connecting low pressure irrigation tubing and drip lines to LDPE supply lines.

Features Ÿ Reduce time and installation costs. Ÿ 8 mm x 13 mm elbow suitable for installation from 19 mm LDPE tube. Ÿ 10 mm inlet ttings suitable for installation from 25 mm LDPE tube. Ÿ Take-Off elbows are ideal for installing drip lines at any angle to the supply line ensuring parallel lateral lines in sub surface or above ground drip systems.

Applications Sub surface and above ground drip irrigation systems and landscape watering applications.

Ordering Information - Take-Off Fittings

FITTINGS

Type

Take-Off Joiner 10 mm x 13 mm

Take-Off Joiner 10 mm x 13 mm Take-Off Joiner 10 mm x 14 mm Take-Off Elbow 10 mm x 13 mm Take-Off Elbow 10 mm x 14 mm Take-Off Elbow 8 mm x 13 mm

25 mm LDPE Tube Take-Off Joiner

“DB” Joiner

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

46405 46395 46415 46435 46425

25 25 25 25 25

120 108 90 85 100

11.6 12.1 12.0 112.0 12.4

Drip Tube

Asta Hold Down Stake

Take-Off Joiner 10 mm x 14 mm

Asta Hold Down Stake Take-Off Elbow

Drip Tube

25 mm LDPE Tube Take-Off Elbow 10 mm x 13 mm

Take-Off Elbow 10 mm x 14 mm

Take-Off Elbow 8 mm x 13 mm

39

Installation

Ÿ Ÿ

To install, use an 8 mm hole punch for Take-Off Elbow 8 mm x 13 mm.

Use a 10 mm hole punch for 10 mm x 13 mm & 10 mm x 14 mm models.

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Xpando® Take-Off Fittings Antelco Xpando® Take-Off Adaptors are an improved method of connecting low pressure irrigation tubes and drip lines from HDPE and uPVC pipes and sub mains with a Capo® Grommet.

Features Ÿ Easy to install, reducing both time and cost of installation. ® Ÿ Innovative Xpando Take-Off Adaptor with collapsible barb prevents pullout and reduces grommet damage during the installation process. ® ® Ÿ Capo Grommet with internal step combines with Xpando interference barb to hold off-take rmly in place. Ÿ UV stabilised materials for long life.

Applications Agricultural, horticultural, vineyard and landscape applications.

Ordering Information - Xpando® Take-Off Adaptors Type

Pack Quantity

Packs per Carton

Carton (kg)

45875 45885 45605 45595 45615 45635 45585 45995 45665 45675 45685

25 25 25 25 25 25 25 25 25 25 25

65 56 60 60 48 35 32 26 26 24 18

9.8 9.3 8.7 9.5 8.2 8.8 8.3 9.4 9.4 9.3 8.0

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

45725 45735 45745 45755

100 100 100 100

40 40 24 18

12.7 10.5 10.8 10.4

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

51835 51845 51855 51865

1 1 1 1

36 36 36 36

1.8 2.2 2.8 3.6

FITTINGS

Xpando® 10 mm inlet x 14 mm Take-Off (16 OD) Xpando® 10 mm inlet x 15 mm Take-Off (17 OD) Xpando® 13 mm inlet x 13 mm Take-Off Xpando® 13 mm inlet x 14 mm Take-Off (16 OD) Xpando® 13 mm inlet x 15 mm Take-Off (17 OD) Xpando® 16 mm inlet x 16 mm Take-Off (18 OD) Xpando® Take-Off Adaptor Xpando® 16 mm inlet x 18 mm Take-Off (20 OD) NEW Xpando® 19 mm inlet x 18 mm Take-Off (20 OD) Xpando® 19 mm inlet x 19 mm Take-Off Xpando® 19 mm inlet x 21 mm Take-Off (23 OD) Xpando® 19 mm inlet x 25 mm Take-Off (27 OD)

Order Code

Ordering Information - Capo® Rubber Grommets Type

Capo® Rubber Grommet

Capo® Rubber Grommet 10 mm Capo® Rubber Grommet 13 mm Capo® Rubber Grommet 16 mm Capo® Rubber Grommet 19 mm

Ordering Information - Xpando® Drill Bits Type

Drill Bit for Xpando®

14 mm Drill Bit for 10 mm Xpando® 16 mm Drill Bit for 13 mm Xpando® 19 mm Drill Bit for 16 mm Xpando® 22 mm Drill Bit for 19 mm Xpando®

Xpando® Take -Off Adaptor

Xpando® 10 mm x 14 mm Xpando® 10 mm x 15 mm Xpando® 13 mm x 13 mm Xpando® 13 mm x 14 mm Xpando® 13 mm x 15 mm Xpando® 16 mm x 16 mm Xpando® 16 mm x 18 mm Xpando® 19 mm x 18 mm Xpando® 19 mm x 19 mm Xpando® 19 mm x 21 mm Xpando® 19 mm x 25 mm

Min. ID

Min. Wall Thickness

Max. Wall Thickness

Capo® Grommet

Hole Size Grommet

25 mm (only)

1.5 mm

3.6 mm

10 mm (curved)

14 mm

40 mm

1.5 mm

2.3 mm

13 mm

16 mm

50 mm

1.5 mm

3.6 mm

16 mm

19 mm

50 mm

1.5 mm

6.0 mm

19 mm

22 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

40

Xpando® Take-Off Director Threaded Xpando® Take-Off Directors allow direct connection of threaded sprinkler risers to rigid sprinkler lateral pipework.

Features ® Ÿ Proven Xpando positive seal proof connection. Ÿ ½” BSPM thread connection for riser. Ÿ Large 19 mm Take-Off reduces friction losses. ® Ÿ Uses standard CAPO rubber grommets. Ÿ Uses standard recommended 22 mm drill bit for installation.

Applications Lateral Take-Off tting for sprinkler riser installations. Is a more economical method than the traditional tapping saddle method.

FITTINGS

Connect to threaded uPVC and rigid HDPE pipe systems.

1/2" BSPM Threaded Director to connect to threaded sprinkler riser.

Xpando® Take-Off Director 1/2" BSPM x 19 mm

Easy to install, proven Xpando® positive seal proof connection to lateral pipework.

Capo® Rubber Grommet 19 mm

22 mm Drill Bit for 19 mm Xpando®

Ordering Information - Xpando® Director Type Xpando® Director 1/2" BSPM x 19 mm Take-Off Capo® Rubber Grommet 19 mm 22 mm Drill Bit for 19 mm Xpando®

Xpando® Director

Xpando® Director 19 mm

41

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

45985 45755 51865

20 100 1

20 18 36

10.1 10.4 3.6

Min. ID

Min. Wall Thickness

Max. Wall Thickness

Capo® Grommet

Hole Size Grommet

50 mm

1.5 mm

6.0 mm

19 mm

22 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Directors, End Plugs & Saddles Used with low density polyethylene (LDPE) tubing in low pressure irrigation systems.

Features Ÿ Directors adapt tubes to valves and female threaded ttings. Ÿ End Sleeves and Plugs used to terminate tube ends. Ÿ Saddle clamps used to secure tubing. Ÿ Compatible with Australian and International tube sizes. Ÿ UV stabilised materials for long life. Ÿ Operating pressure range up to 300 kPa. Applications Directors connect to threaded ttings, End Plugs terminate irrigation supply, Saddles and Clips secure irrigation tubes.

Ordering Information - Directors Order Code

Pack Quantity

Packs per Carton

Carton (kg)

Director 1/2" BSPM x 13 mm Director 3/4" BSPM x 13 mm Director 1" BSPM x 13 mm Director 1/2" BSPM x 19 mm Director 3/4" BSPM x 19 mm Director 1" BSPM x 19 mm Director 3/4" BSPM x 25 mm Director 1" BSPM x 25 mm Director 1" BSPM x 32 mm

45255 45265 45275 45285 45295 45305 45325 45315 45335

25 25 25 25 25 25 25 25 25

45 35 20 40 30 18 23 15 12

6.5 6.9 6.9 6.8 6.7 6.7 7.0 6.2 6.1

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

44555 44565 44575 44585

25 25 25 25

110 50 24 16

7.2 7.0 7.0 5.7

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

44605

25

40

5.4

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

45355 45365 45375

100 100 100

170 56 26

18.2 18.7 15.9

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

45395 45405 45415

100 100 100

90 45 26

9.3 7.2 6.6

FITTINGS

Director

Type

Ordering Information - End Plugs Type

End Plug

End Plug 13 mm End Plug 19 mm End Plug 25 mm End Plug 32 mm

Ordering Information - End Sleeve Type End Sleeve 13 mm End Sleeve

Ordering Information - Saddle Clips Type

Saddle Clip

Saddle Clip 4 mm with nail Saddle Clip 13 mm with nail Saddle Clip 19 mm with nail

Ordering Information - Saddle Clamps Type

Saddle Clamp

Saddle Clamp 4 mm Saddle Clamp 13 mm Saddle Clamp 19 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

42

Joiners and Elbows A range of polypropylene ttings designed to control, disperse, slow and divert water through a low pressure irrigation system. Used in conjunction with low density poly (LDPE) tubing.

Features Ÿ Tapered entry on all barbed ttings for ease of installation. Ÿ Range suits common Australian and International tube sizes. Ÿ UV stabilised materials for long life. Ÿ Operating pressure range up to 300 kPa. Applications Home gardens, landscaping and commercially installed irrigation systems.

Ordering Information - Joiners

FITTINGS

Type Joiner 13 mm Joiner 15 mm Joiner 18 mm Joiner 19 mm Joiner 21 mm Joiner 25 mm Joiner 32 mm Reducing Joiner 16 mm x 15 mm Reducing Joiner 19 mm x 13 mm Reducing Joiner 19 mm x 15 mm Reducing Joiner 19 mm x 18 mm Reducing Joiner 21 mm x 19 mm Reducing Joiner 25 mm x 13 mm Reducing Joiner 25 mm x 19 mm Reducing Joiner 32 mm x 25 mm

Joiner

Reducing Joiner

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

44705 46005 46015 44715 46025 44735 44745 46055 44805 46065 46075 46085 44765 44775 46095

25 25 25 25 25 25 25 25 25 25 25 25 25 25 25

90 60 50 40 36 20 10 60 50 50 44 40 32 26 12

6.9 6.6 7.1 6.1 5.9 6.3 4.7 7.2 6.2 6.6 6.3 5.9 6.8 5.9 4.6

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

44835 44865 44875 44825 44955 44965 44975 44885 44905 44915 44925 44935 45005 46155 46165 46175 46185

25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25

75 36 14 8 28 24 16 34 36 25 17 14 16 50 36 35 30

6.6 5.6 5.8 5.1 8.5 7.7 6.7 6.4 5.8 5.6 6.2 6.2 8.7 7.3 6.0 6.3 5.9

Ordering Information - Elbows Type

Elbow

Threaded Elbow Female

Elbow 13 mm Elbow 19 mm Elbow 25 mm Elbow 32 mm Threaded Elbow 13 mm x 1/2" BSPF Threaded Elbow 19 mm x 1/2" BSPF Threaded Elbow 25 mm x 1/2" BSPF Threaded Elbow 13 mm x 1/2" BSPM Threaded Elbow 19 mm x 1/2" BSPM Threaded Elbow 19 mm x 3/4" BSPM Threaded Elbow 25 mm x 1/2" BSPM Threaded Elbow 25 mm x 3/4" BSPM Threaded Corner Elbow 19 mm x 1/2" BSPM Reducing Elbow 16 mm x 15 mm Reducing Elbow 19 mm x 15 mm Reducing Elbow 19 mm x 18 mm Reducing Elbow 21 mm x 19 mm

Threaded Elbow Male

43

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Tees and Crosses A range of polypropylene ttings designed to control, disperse, slow and divert water through a low pressure irrigation system. Used in conjunction with low density poly (LDPE) tubing.

Features Ÿ Tapered entry on all barbed ttings for ease of installation. Ÿ Range includes common Australian and International tube sizes. Ÿ UV stabilised materials for long life. Ÿ Operating pressure range up to 300 kPa. Applications Home gardens, landscaping and commercially installed irrigation systems.

Ordering Information - Tees Pack Quantity

Packs per Carton

Carton (kg)

Tee 13 mm Tee 19 mm Tee 25 mm Tee 32 mm Reducing Tee 19 mm line x 13 mm branch Reducing Tee 21 mm line x 19 mm branch Reducing Tee 25 mm line x 13 mm branch Reducing Tee 25 mm line x 19 mm branch Reducing Tee 32 mm line x 25 mm branch

45035 45065 45075 45085 45105 46255 45115 45125 45135

25 25 25 25 25 25 25 25 25

48 22 8 4 24 18 11 10 5

6.3 5.3 4.9 3.7 5.2 5.4 5.3 5.3 4.0

Tee

Threaded Tee 13 mm line x 1/2" BSPF branch Threaded Tee 19 mm line x 1/2" BSPF branch Threaded Tee 25 mm line x 1/2" BSPF branch Threaded Tee 13 mm line x 1/2" BSPM branch Threaded Tee 19 mm line x 1/2" BSPM branch Threaded Tee 19 mm line x 3/4" BSPM branch Threaded Tee 25 mm line x 1/2" BSPM branch Threaded Tee 25 mm line x 3/4" BSPM branch Increasing Tee 15 mm line x 16 mm branch Increasing Tee 15 mm line x 19 mm branch Increasing Tee 18 mm line x 19 mm branch

45155 45165 45175 45185 45205 45215 45225 45235 46305 46315 46325

25 25 25 25 25 25 25 25 25 25 25

18 15 10 25 22 16 10 9 27 24

6.9 6.3 5.8 6.5 5.2 4.6 5.4 5.4 7.1 5.8 5.5

Threaded Tee Female

Threaded Tee Male

20

FITTINGS

Order Code

Type

Ordering Information - Cross Type Cross 13 mm

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

44635

25

26

4.2

Cross 13 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

44

Double Barb “DB” FittingsTM The “DB” range of purpose designed quality acetal ttings provides high retention in low pressure poly (LDPE) tubing for long-term reliability of connections.

Features Ÿ Double barb for increased retention. Ÿ Sharp-edged barbs create leak-proof seal. Ÿ Increased strength and superior quality. Ÿ Heat, chemical and wear resistant. Ÿ Engineering grade UV stabilised Acetal plastic for long life. Ÿ Operating pressure range up to 300 kPa. Ÿ The space between double barbs allows extra security for clamping.

Applications Vineyard and other agricultural applications. Ideal for trellis and suspended irrigation systems.

Ordering Information - “DB” Joiners

FITTINGS

Type

“DB” Joiner

13 mm 14 mm (suits 16 O.D. tube) 15 mm (suits 17 O.D. tube) 16 mm 17 mm (suits 20 O.D. tube) 18 mm (suits 20 O.D. tube) 19 mm 21 mm (suits 22/23 O.D. tube) 25 mm

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

47005 47015 46975 47025 47815 47035 46985 47045 46995

25 25 25 25 25 25 25 25 25

90 72 64 56 50 50 40 34 20

11.0 10.2 10.2 9.5 9.9 9.8 8.8 8.6 7.2

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

47845 47075 47085 47055 47095 47125 47855 47155 47185 47065 47105 47135 47145 47175 47195 46965

25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25

72 60 56 54 50 50 45 40 36 32 32 28 28 26 26 24

10.0 9.7 10.2 9.9 9.6 9.9 9.3 8.5 8.8 8.7 9.4 8.0 8.1 7.8 7.9 7.7

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

47205 47215 47375 47225 47235 47265 47245 47255

25 25 25 25 25 25 25 25

75 54 50 42 36 32 24 14

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

47275 47305 47325

25 25 25

48 40 34

9.5 9.4 8.9

Ordering Information - “DB” Reducing Joiners Type

“DB” Reducing Joiner

13 mm x 14 mm I.D. (suits 16 O.D. Dripline) 16 mm x 14 mm I.D. (suits 16 O.D. Dripline) 18 mm x 14 mm I.D. (suits 16 O.D. Dripline) 19 mm x 13 mm 19 mm x 14 mm I.D. (suits 16 O.D. Dripline) 19 mm x 15 mm I.D. (suits 17 O.D. Dripline) 19 mm x 17 mm I.D. (suits 20 O.D. Dripline) 19 mm x 18 mm I.D. (suits 20 O.D. Dripline) 19 mm x 21 mm I.D. (suits 22/23 O.D. Dripline) 25 mm x 13 mm 25 mm x 14 mm I.D. (suits 16 O.D. Dripline) 25 mm x 15 mm I.D. (suits 17 O.D. Dripline) 25 mm x 16 mm 25 mm x 18 mm I.D. (suits 20 O.D. Dripline) 25 mm x 19 mm 25 mm x 21 mm I.D. (suits 22/23 O.D. Dripline)

Ordering Information - “DB” Elbows “DB” Elbow

Type 13 mm 14 mm (suits 16 O.D. Dripline) 15 mm (suits 17 O.D. Dripline) 16 mm 18 mm (suits 20 O.D. Dripline) 19 mm 21 mm (suits 22/23 O.D. Dripline) 25 mm

10.9 9.8 9.6 8.9 9.2 8.7 7.9 6.7

Ordering Information - “DB” Reducing Elbows Type “DB” Reducing Elbow

45

16 mm x 14 mm (suits 16 O.D. Dripline) 19 mm x 15 mm (suits 17 O.D. Dripline) 19 mm x 18 mm (suits 20 O.D. Dripline)

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Double Barb “DB” FittingsTM The “DB” FittingsTM range can be condently installed without clamps when matched to quality low pressure poly (LDPE) tubing with corresponding dimensions (refer to the tubing manufacturer for conrmation of suitability or test under eld conditions).

Operating pressures up to 300 kPa. Size options: Ÿ 13 mm - Suits nominal 13 mm I.D. tube Ÿ 14 mm - Suits nominal 14 mm I.D. and 16 mm O.D. tube (Dripline) Ÿ 15 mm - Suits nominal 15 mm I.D. and 17 mm O.D. tube (Dripline) Ÿ 16 mm - Suits nominal 16 mm I.D. and 18 mm O.D. tube (Dripline) Ÿ 18 mm - Suits nominal 18 mm I.D. and 20 mm O.D. tube (Dripline) Ÿ 19 mm - Suits nominal 19 mm I.D. tube Ÿ 21 mm - Suits nominal 21 mm I.D. and 23 mm O.D. tube (Dripline) Ÿ 25 mm - Suits nominal 25 mm I.D. tube and 27 mm O.D. tube (Dripline)

Ordering Information - “DB” Tees Type

“DB” Tee

Pack Quantity

Packs per Carton

Carton (kg)

47405 47415 47395 47425 47435 47605 47445 47455

25 25 25 25 25 25 25 25

48 30 28 24 22 18 16 10

10.4 8.1 7.9 7.5 8.1 7.1 7.7 6.8

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

47475 47485 47505 47525

25 25 25 25

26 26 26 20

7.6 8.2 8.6 7.6

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

47765 47465 47535 47755 47555 47585 47695

25 25 25 25 25 25 25

56 48 22 22 16 13 13

10.1 9.4 8.0 8.2 7.2 7.3 7.4

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

48035 48015 48025 48045

25 25 25 25

58 56 50 50

11.5 11.5 10.6 10.7

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

47685 47615 47625 47635 47665 47645

25 25 25 25 25 25

120 100 72 60 56 40

12.4 11.7 10.2 9.9 10.3 8.4

FITTINGS

13 mm 14 mm (suits 16 O.D. tube) 15 mm (suits 17 O.D. tube) 16 mm 18 mm (suits 20 O.D. tube) 19 mm 21 mm (suits 22/23 O.D. tube) 25 mm

Order Code

Ordering Information - “DB” Increasing Tees Type 14 mm (16 O.D. Dripline) x 16 mm branch 14 mm (16 O.D. Dripline) x 19 mm branch 15 mm (17 O.D. Dripline) x 19 mm branch 18 mm (20 O.D. Dripline) x 19 mm branch

“DB” Increasing Tee

Ordering Information - “DB” Reducing Tees Type “DB” Reducing Micro Tee

“DB” Reducing Tee

13 mm line x 4 mm branch 14 mm (16 O.D. Dripline) x 4 mm branch 19 mm line x 13 mm branch 19 mm line x 14 mm branch (suits 16 O.D. Dripline) 21 mm (22/23 O.D. Dripline) x 19 mm branch 25 mm line x 13 mm branch 25 mm line x 14 mm branch (suits 16 O.D. Dripline)

Ordering Information - “DB” Director 1/2" Male Thread Type 1/2" Male Thread x 13 mm 1/2" Male Thread x 14 mm 1/2" Male Thread x 15 mm 1/2" Male Thread x 16 mm

“DB” Director

Ordering Information - “DB” End Plugs Type

“DB” End Plug

13 mm 14 mm (suits 16 O.D. tube) 16 mm 18 mm (suits 20 O.D. tube) 19 mm 21 mm (suits 22/23 O.D. tube)

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

46

Super Tough “ST” Fittings Super Tough “ST” Fittings are manufactured from high strength engineering grade plastic to provide improved resistance to impact and loading in high stress installations.

Features Ÿ Easily identiable green colour. Ÿ Tapered entry on all barbed ttings for ease of installation. Ÿ Sizes suit most popular drip line tubing; 17 OD, 20 OD & 22/23 OD drip tubes. Ÿ Models to connect 19 mm LDPE to popular drip line tubing. Ÿ Operating pressure range up to 300 kPa. Ÿ UV stabilised material for long eld life.

Applications Vineyard and other agricultural applications. Ideal for trellis and suspended irrigation systems.

Ordering Information - “ST” Joiners Order Code

Pack Quantity

Packs per Carton

Carton (kg)

61005 61015 61025

25 25 25

60 50 36

8.2 8.4 7.3

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

61035 61045 61055

25 25 25

50 44 40

8.0 7.6 7.3

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

61065 61075 61085

25 25 25

36 35 30

7.5 7.9 7.2

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

61095

25

18

6.5

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

15 mm x 15 mm x 19 mm Branch (suits 17 OD Drip Tubes)

61105

25

24

7.1

18 mm x 18 mm x 19 mm Branch (suits 20 OD Drip Tubes)

61115

25

20

6.7

FITTINGS

Type

21 mm x 21 mm “ST” Joiner

15 mm - suits 17 OD Drip Tubes 18 mm - suits 20 OD Drip Tubes 21 mm - suits 22/23 OD Drip Tubes

Ordering Information - “ST” Reducing Joiners Type 19 mm x 15 mm - suits 17 OD Drip Tubes 19 mm x 18 mm - suits 20 OD Drip Tubes 19 mm x 21 mm - suits 22/23 OD Drip Tubes

19 mm x 15 mm “ST” Reducing Joiner

Ordering Information - “ST” Reducing Elbows Type 19 mm x 15 mm - suits 17 OD Drip Tubes 19 mm x 18 mm - suits 20 OD Drip Tubes 19 mm x 21 mm - suits 22/23 OD Drip Tubes

19 mm x 15 mm “ST” Reducing Elbow

Ordering Information - “ST” Reducing Tees Type

21 mm x 21 mm x 19 mm Branch “ST” Reducing Tee

21 mm x 21 mm x 19 mm Branch (suits 22/23 OD Drip Tubes)

Ordering Information - “ST” Increasing Tees Type

15 mm x 15 mm x 19 mm Branch “ST” Increasing Tee

47

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Ratchet Clamps Ratchet Clamps secure low density polyethylene (LDPE) tube to a wide range of ttings.

Features Ÿ Smooth edges allow assembly by hand. Ÿ Range of sizes to suit most low density poly (LDPE) tube connections. Ÿ Sharp serrated teeth provide secure lock and rmly hold tube to tting. Ÿ Can be twisted and unclamped if required. Ÿ Also suitable for dripline tubing. Ÿ Improved ratcheting action and ability to t to a trellis wire.

Applications Home gardens and landscaping applications.

Ordering Information - Ratchet Clamps Order Code

Pack Quantity

Packs per Carton

Carton (kg)

13 mm Ratchet Clamp #15 Ratchet Clamp #17 16 mm Ratchet Clamp #18 Ratchet Clamp #20 19 mm Ratchet Clamp #22 Ratchet Clamp #23 25 mm Ratchet Clamp #28

44305 44345 44335 44295 44315 44285 44325

100 100 100 100 100 100 100

50 45 45 40 35 32 16

12.4 11.8 11.2 11.1 10.6 10.6 10.1

FITTINGS

Type

Ratchet Clamp Suits ID Poly Tube

Tube OD Range

Suits OD Dripline

13 mm

15 - 16 mm

15 mm

14 mm

16 - 18 mm

16 - 17 mm

16 mm

17 - 19 mm

18 mm

18 mm

19 - 21 mm

20 mm

19 mm

21 - 23 mm

22 mm

21 mm

22 - 24 mm

23 mm

25 mm

27 - 30 mm

27 mm

#15

#17

#18

#20

#22

#23

#28

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

48

®

Asta Stakes and Rigid Risers The Asta® Stake range provides a variety of solutions for stabilising the components of micro irrigation systems.

Features ® Ÿ Asta Stakes suitable for plasticised PVC and polyethylene tubing and Rigid Risers (6.9 mm OD). ® Ÿ Asta Stake Assemblies suitable for most micro spray and micro sprinkler installations with 4 mm threaded inlets. Ÿ UV stabilised materials for long life.

Applications Asta® Stakes for rigid riser stability; Asta® Stake Assemblies for home gardens and landscape applications.

Ordering Information - Asta® Stakes Type

FITTINGS

Asta® Stake 200 mm Asta® Stake 310 mm Asta® Stake 420 mm Asta® Stake 530 mm

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

40885 40875 40895 40905

25 25 25 25

28 20 12 10

9.9 10.8 9.1 9.5

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

41005

100

120

12.4

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

43685 43695

25 25

19 14

11.8 12.3

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

43125 43135 43145

100 100 100

26 18 11

12.6 13.8 12.8

Ordering Information - Asta® Stake Adaptor Type Asta® Stake Adaptor 4 mm (F) x 4.5 mm barb

Ordering Information - Asta® Stake Assemblies Type Asta® Stake Assembly w/ 300 mm off-take tube Asta® Stake Assembly w/ 600 mm off-take tube

Asta® Stake 310 mm

Ordering Information - Rigid Risers Type Asta® Stake Adaptor

Asta® Stake Assembly

49

Rigid Riser

200 mm with ‘Quick’ thread adaptor tted 300 mm with ‘Quick’ thread adaptor tted 450 mm with ‘Quick’ thread adaptor tted

Asta® Stake - 200 mm, 310 mm, 420 mm, and 530 mm

Rigid Riser - 200 mm, 300 mm, and 450 mm

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Micro Stakes The Micro Stake provides a solution for positioning of micro sprays for landscapes and orchards. Available as a plain stake or tted with differing lengths of tube to suit most installations.

Features Ÿ Tube piercing point on each stake tip allows creation of holes in laterals, removing the need for a separate installation tool. Ÿ Robust design Ÿ Retaining hole in stake to align and support offtake tubing. Ÿ UV stabilised materials for long life.

Applications Landscape and agricultural orchard applications.

Ordering Information - Micro Stakes Type

NEW

Pack Quantity

Packs per Carton

Carton (kg)

40825 40835 40784 40705

25 25 25 25

8 6 6 5

5.9 6.0 8.0 5.9

FITTINGS

Micro Stake 4 mm barb inlet Micro Stake with 400 mm tube and Adaptor Micro Stake with 500 mm tube and Adaptor Micro Stake with 600 mm tube and Adaptor

Order Code

Micro Stake with off-take tube

NEW

400 mm Assembly

500 mm Assembly

600 mm Assembly

Micro Stake

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

50

Hold Down Stakes The Asta® Stake range includes solutions for restraining tubing in micro irrigation systems.

Features ® Ÿ Asta Clip stake locates and secures micro polyethylene tubing (up to 7mm OD). ® Ÿ Asta Hold Down stake locates and secures polyethylene tubing (up to 22 mm OD). Ÿ UV stabilised materials for long life.

Applications Securing drip and micro irrigation tubing in home gardens, landscaping, and agricultural installations.

Ordering Information - Asta® Clip Stake Type

FITTINGS

Asta® Clip Stake

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

43595

25

100

11.8

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

43615

25

25

10.0

Ordering Information - Asta® Hold-Down Stake Type Asta® Hold-Down Stake

Asta® Clip Stake

Asta® Hold-Down Stake

51

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Mini Sprinkler Stakes Rotor StakeTM and Sprinkler Adaptors to install mini sprinklers in agricultural and landscape installations.

Features TM Ÿ Rotor Stake available with 5 mm, 10 mm and 13 mm barb inlet.

TM Ÿ Rotor Stake has a tube piercing point for hole punch installation of 4 mm Adaptors on micro tube, a retainer hole to align and support micro tubing. Ÿ Sprinkler Adaptors available in 5 mm, 10 mm and 13 mm barb to suit trellis installation. Ÿ Collar pipe Sprinkler Adaptor available in 5 mm, 10 mm and 13 mm barb to suit 20mm uPVC or Galvanised pipe risers. Ÿ Rod Stake Sprinkler Adaptors available in 5 mm and 10 mm barb to suit 5 mm Fibreglass or Steel Rods. Ÿ Robust design with UV stabilised materials for long eld life.

Applications All stakes and Adaptors suit Rotor Rain® and Rotor MaxTM and industry 3/8" Male threaded micro sprinklers.

NEW

Ordering Information - Rotor StakeTM 3/8" BSPF with Barb Adaptor Type

Pack Quantity

Packs per Carton

Carton (kg)

40555 40515 40535 40675

25 25 25 25

6 6 6 4

5.1 5.2 5.3 5.9

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

40755 40715 40735

50 50 50

40 34 30

6.8 6.7 6.2

Packs per Carton

Carton (kg)

Rotor StakeTM for typical orchard or landscape installations

Ordering Information - Sprinkler Adaptor 3/8" BSPF Type Sprinkler Adaptor 3/8" BSPF x 5 mm Sprinkler Adaptor 3/8" BSPF x 10 mm Sprinkler Adaptor 3/8" BSPF x 13 mm

FITTINGS

Rotor StakeTM 3/8" BSPF with 5 mm barb Rotor StakeTM 3/8" BSPF with 10 mm barb Rotor StakeTM 3/8" BSPF with 13 mm barb Rotor StakeTM 3/8" BSPF with 600 mm tube & ad.

Order Code

Sprinkler Adaptor for typical trellis wire installations

Ordering Information - Collar Pipe Sprinkler Adaptor 3/8" BSPF Type

Rotor StakeTM

NEW

Order Code

Pack Quantity

5.5 Collar Pipe Sprinkler Adaptor with 5 mm barb 50 10 40655 5.6 Collar Pipe Sprinkler Adaptor with 10 mm barb 50 10 40615 5.8 Collar Pipe Sprinkler Adaptor with 13 mm barb 50 10 40635 Collar Pipe Sprinkler Adaptor for 20mm uPVC or Galvanised riser installations (26.7 mm OD)

Ordering Information - Rod Stake Sprinkler Adaptor 3/8" BSPF Type Rod Stake Sprinkler Adaptor 3/8" BSPF x 5 mm Rod Stake Sprinkler Adaptor 3/8" BSPF x 10 mm

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

40815 40855

50 50

35 24

7.1 5.6

Rod Stake Sprinkler Adaptor for 5mm OD Fibreglass or Steel rod riser installations

Sprinkler Adaptor

Collar Pipe Sprinkler Adaptor

Rod Stake Sprinkler Adaptor

TM

Rotor Stake with 600 mm Tube and Adaptor Antelco irrigation equipment metric catalogue 2020 www.antelco.com

52

Tap Fittings A range of quick connect ttings specically designed to connect polyethylene irrigation tubes to taps and Snap-On ttings. Connect to tap adaptors, tap timers, taps, manifold and multi outlet distributors.

Features Ÿ Simple to use ergonomic design. Ÿ Tap Adaptor suits Snap-On connections. Ÿ UV stabilised materials for long life.

Applications Home gardens and landscaping applications.

Ordering Information - Nuts and Tails Order Code 44005 44065 44055 44015 44025 44035 44045

Pack Quantity 25 25 25 25 25 25 25

Packs per Carton 34 34 34 30 27 23 18

Carton (kg) 10.3 10.6 10.9 9.4 10.3 9.6 9.0

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

44505 44515

25 25

50 36

10.6 10.3

Type

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

Washer suits 3/4" Nut&Tail, Snap-On Tap Adaptor Washer suits 1" Nut&Tail, Snap-On Tap Adaptor

44075 44085

100 100

115 70

9.5 8.7

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

45775 45785 45815 45825

25 25 25 25

38 30 44 30

10.0 9.8 9.3 12.0

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

45465 45475 45485

25 25 25

35 32 28

12.2 12.0 10.9

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

45455 45445

25 25

100 48

8.9 8.0

FITTINGS

Type

Nut and Tail

Nut and Tail with Washer 3/4" BSPF x 13 mm Nut and Tail with Washer 3/4" BSPF x 14 mm Nut and Tail with Washer 3/4" BSPF x 16 mm Nut and Tail with Washer 3/4" BSPF x 19 mm Nut and Tail with Washer 1" BSPF x 13 mm Nut and Tail with Washer 1" BSPF x 19 mm Nut and Tail with Washer 1" BSPF x 25 mm

Blank Nut

Ordering Information - Blank Nuts Type Blank Nut with Washer 3/4" BSPF Blank Nut with Washer 1" BSPF

Washer

Ordering Information - Washers

Snap-On Tap Adaptor

Tap Adaptor BSPF x BSPM

Ordering Information - Snap-On Tap Adaptors Type Snap-On Tap Adaptor 3/4" BSPF Snap-On Tap Adaptor 1" BSPF Tap Adaptor Reducing Bush 1" BSPM x 3/4" BSPF Tap Adaptor 1" BSPF x 3/4" BSPM

Ordering Information - Snap-On Connectors Type Snap-On Connector x 13 mm barb Snap-On Connector x 16 mm barb Snap-On Connector x 19 mm barb Snap-On Tap Adaptor Connector Barb Reducing Bush

Ordering Information - Snap-On Joiners Type Snap-On Joiner x 13 mm barb Snap-On Joiner x 19 mm barb

Snap-On Joiner

53

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Filters Filtration devices designed to trap foreign particles in the water and reduce risk of clogging of emitters.

Features Ÿ In-Line model with barbed inlet and outlet. Ÿ Snap-On model for direct connection to standard tap adaptors. Ÿ 80 mesh screen lter. Ÿ Easily taken apart for cleaning. Ÿ Effective compact lters with minimal ow losses.

Applications For low pressure micro irrigation systems.

Ordering Information - In-line Filters 80 mesh Screen Type

Pack Quantity

Packs per Carton

44355 44395 44365 44375 44445

25 25 25 25 10

14 14 12 6 8

Carton (kg) 10.9 10.2 9.9 7.4 7.0

FITTINGS

In-Line Filter 13 mm barb In-Line Filter 14 mm barb In-Line Filter 16 mm barb In-Line Filter 19 mm barb In-Line Filter 25 mm barb

Order Code

Ordering Information - Snap-On Filters 80 mesh Screen

In-Line Filter

Snap-On Filter

Type

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

Snap-On Filter 13 mm barb Snap-On Filter 14 mm barb Snap-On Filter 16 mm barb Snap-On Filter 19 mm barb

44405 44435 44415 44425

25 25 25 25

10 10 10 6

9.5 9.5 9.6 8.5

Specications - In-Line Filter Dimensions Assembled

13, 14 16 mm

19 mm

Material

LENGTH 132 mm 175 mm TAIL Inlet WIDTH 33 mm 40 mm BODY & NUT WEIGHT (approx.) 28 g 43 g WASHER SCREEN

Base/Connection type

acetal Inlet Barb 13, 14, 16, 19 mm polyproplene Outlet Barb 13, 14, 16, 19 mm TPE HDPE

Specications - Snap-On Filter Dimensions Assembled

13, 14 16 mm

19 mm

Material

Base/Connection Type

LENGTH 134 mm 175 mm BODY Snap-On Inlet acetal Inlet Snap-On Connector polyproplene Outlet Barb 13, 14, 16,19 mm WIDTH 33 mm 40 mm SLEEVE WEIGHT (approx.) 35 g 51 g BODY & NUT polyproplene WASHER TPE SCREEN HDPE

In-Line Filter 25 mm

In-Line Filter cut away detail Antelco irrigation equipment metric catalogue 2020 www.antelco.com

54

Installation Tools Tools to assist in the installation of micro irrigation systems.

Features TM Ÿ Key Punch creates holes in tubing for inserting emitters. The sleeve assists in installing hexagonal based jets and the hole aids removal of jet caps for cleaning. Ÿ 2 in 1 Punch and Cutter is designed for cutting CVT and LDPE tubing up to 19 mm (21 mm OD) and punching holes into tubing for emitters and ttings. Ÿ 2 in 1 Punch and Cutter comes pre-packaged in ready-to-hang retail pack.

Applications For installing micro irrigation systems by home gardeners, contractors and professional irrigators.

Ordering Information - Installation Tools

ACCESSORIES

Type Key PunchTM 2 in 1 Punch & Cutter

Order Code

Pack Quantity

Packs per Carton

Carton (kg)

42315 42375

25 1

120 95

12.1 8.8

Key PunchTM

Cuts low density poly pipe and vinyl tubing up to 22 mm OD.

2 in 1 Punch & Cutter

2 in 1 Punch & Cutter

Punches holes into tubing ready for the insertion of emitters and ttings.

2 in 1 Punch & Cutter Retail Packaging

55

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

36

Dripper Installation Guidelines Installation Guidelines - Home Garden Drippers ®

INSTALLING POTSTREAM DRIPPERS Adjust the water application rate to suit the size of pot or plant type by rotating the cap.

Connect to your 13 mm tube by pushing the 4 mm joiner into holes you have punched in the tube.

Cut a length of 4 mm micro tube to suit the location of your pot plant, then push a 4 mm joiner into one end of the tube and ® a Potstream into the other.

Clip on a Tidy-BowTM Elbow to keep tube neatly beside your pots.

®

TM

INSTALLING SHRUBBLER , SPECTRUM

The cap can also be fully closed to stop the ow.

OR MINI BUBBLER SPIKES

Twist off the barbed joiner attached to the side of the spike.

Cut 4 mm micro tube to a suitable length for each plant location. Push the barbed joiner into one end of the tube, then push the ® Shrubbler , SpectrumTM or Mini Bubbler Spike into the other end of the tube.

®

Connect your Shrubbler , SpectrumTM or Mini Bubbler barb to your 13 mm tube by pushing the barbed joiner into a hole you have created in the tube using the tube punch.

Adjust the water application rate of your ® Shrubbler , SpectrumTM or Mini Bubbler Spike by rotating the cap. The cap can also be fully closed to stop ow.

INSTALLING ASTA® DRIP SPIKES Cut 4 mm ID tube to a suitable length for each plant location.

Push a 4 mm joiner into one end of the tube, then push the other end of the ® tuber onto the Asta Drip Spike. ®

Connect your Asta Drip Spike to your 13 mm tube by pushing the 4 mm joiner into a hole you have created in the tube using the Tube Punch.

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

56

Web Information Visit our website...

Visit our website for product updates, installation guides and videos, and general irrigation information.

www.antelco.com

Follow us Antelco

@antelco_

Antelco

Antelco Irrigation

Finding a distributor is just a click away...

Check out our website for a distributor near you.

57

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Micro Irrigation: Facts to Consider Typical Agricultural Micro Irrigation System Pump

Fertigation/Chemigation Zone Control Filtration Valve ain ubm M S ai nl in ma Zone Control ine Sub Valve

Water Supply

La

te

ra

l

ain

bmain

Su

Subm

La

Emitter

te

ra

l

La ra te

Emitter

l A typical agricultural micro irrigation system features the following core elements: Ÿ

Water Supply - The water supply can be an open water source such as a river, channel, dam or tank or a ground water supply such as a bore or a well.

Ÿ

Pump - The pump provides the energy for the system to operate. Pump selection needs to consider the operating pressure of the micro emitters, pipe friction losses, elevation differences, valves and ttings losses, ltration losses and allow some contingencies for system inefciencies and system ageing. A good pump selection will ensure that the pump operating efciencies are at their peak.

Ÿ

Fertigation/Chemigation - The fertigation system allows for the application of soluble fertilizers to be delivered through the micro irrigation system. This can be a very effective method of applying fertilizers as micro irrigation systems can have application efciencies of up to 90%. Chemigation is the method of applying system cleansing agents such as chlorine and acid injection to clean and ush contaminants out of the system.

Ÿ

Filtration - A ltration system is an essential element of micro irrigation systems for removing particulate matter from the water supply. In open water situations organic matter is usually present and a good method of ltration is the use of media ltration. With ground water situations there is usually more inorganic material and disc and screen lters are often used. Filters require regular backwashing and cleaning which can sometimes be automated. Filters also require regular preventative maintenance to keep them operating in peak condition. It is important to get the right ltration system for your micro irrigation system and we would recommend seeking the assistance of a certied irrigation designer for advice.

Ÿ

Mainline - The mainline pipework transfers the water from the water supply to the zone control valves. The pipe is usually uPVC or PE (Polyethylene) piping systems sized to suit the demand situation. Good design practice is to have water velocities in the mainline pipework system to be less than 1.5 m/s. Changes in direction of pipework in mainlines should also be thrust blocked (anchored with concrete).

Ÿ

Zone Control Valves - The zone control valve turns on and off the zone of emitters. These valves can be simple manual on off valves or fully automated solenoid operated valves. To provide constant pressure to the zone these valves can often incorporate a pressure regulator which can be set to a control downstream pressure. Air vacuum relief valves are also often included at these zone control valve points.

Ÿ

Submain - The submain is the pipework that supplies the lateral pipework. It is usually either uPVC or PE Piping system. ® Xpando Take offs are often used for connecting the submain pipework to the Lateral pipework.

Ÿ

Lateral - The lateral pipework is usually low density polyethylene (LDPE) tubing and runs along the row.

Ÿ

Emitters - Emitters can be drippers, sprays or mini sprinklers which are placed to water the root zone of the crop.

Ÿ

Flushing points - A good micro irrigation system will incorporate ushing points at the end of the submains and the laterals. These points can be opened periodically to ush out any accumulated sediments.

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

58

Australian Conditions of Sale: Antelco Pty Ltd Prices and GST

Returns

Prices set out in the Antelco Australian Bulk Price List are list prices excluding GST. Prices may change without notice and customers may conrm prices at the time of ordering. Antelco tax invoices show GST for each line item, total GST and a nal total including GST.

Goods will be accepted for return only if prior approval has been obtained from Antelco Pty Ltd. The goods must be undamaged, unsoiled and in a saleable condition. All returned goods must include a copy of the original invoice and packing slip. Goods that are approved for return after thirty (30) days from the date of delivery are subject to a 15% restocking charge. Freight cost and risk will remain the responsibility of the customer.

CONDITIONS

Payment and trading terms Payment can be made by cash, cheque, VISA or MasterCard, or by bank transfer (contact Antelco Pty Ltd for bank details).

Credit customers must pay within thirty (30) days of the end of the month appearing on the invoice, or otherwise as agreed in writing.

Product Design

Orders

Compatibility

Orders should be e-mailed to Antelco Head Ofce, Murray Bridge, South Australia.

Antelco Pty Ltd is a manufacturer of irrigation products which are designed for use in outdoor irrigation applications only and low pressure systems where the operating pressure at the product does not exceed 300 kPa. Decisions on the use of Antelco products in any other situation remain the responsibility of the customer. If there is uncertainty as to the particular use of the product, the customer or end-user should test its suitability for that application.

Customers may contact the Antelco Sales Department with special orders. They will be advised whether their order can be satised, together with pricing and anticipated delivery time.

A minimum order handling fee of $20.00 (GST inclusive) will apply to orders with a total value of goods of less than $120.00 (GST inclusive).

Urgent (Air Cargo) Orders Orders for shipment by air must be received before 10.00 am to be despatched the same day, and charges will apply. Airbags are best restricted to three or ve kilograms.

Freight and Insurance All prices are ex-works Murray Bridge South Australia. Delivery from Antelco Murray Bridge is at the customer's expense.

Goods are despatched uninsured and at customer’s risk.

Customers acknowledge that delivery insurance is their responsibility.

Receipt of Goods Ordered goods should be opened promptly on receipt and checked against the enclosed packing slip. If correct, the consignment note should be signed. If any item is missing and not marked as being “back ordered”, immediately advise Antelco.

Back Orders Back orders are treated as new orders. Back orders are invoiced when they are despatched. Customers should advise Antelco if they do not want any items back ordered or if they want back orders cancelled. Antelco will cancel a back order if it has not been despatched.

Antelco Pty Ltd reserves the right to re-design its products and thereby cause changes to the specications, without notice and without incurring any liability.

Risk and Title Risk of loss or damage to the goods, passes to the customer at the time of despatch from the Antelco Pty Ltd warehouse.

Notwithstanding that the risk of the goods may pass to the customer, Antelco Pty Ltd retains all legal and equitable rights of ownership of the goods until payment has been made in full (including interest and any other charges associated with the supply of the goods). The customer shall store and protect the goods separately to identify them as the property of Antelco Pty Ltd until paid in full. The customer may sell the goods in the ordinary course of business, but any monies received for the sale of the goods must be held for the benet of Antelco Pty Ltd. If the customer fails to pay the debt, Antelco Pty Ltd reserves the right to enter the premises where the goods are located, seize the goods to which ownership has not passed, and sell them to recover the amount of debt owed, without being liable for damages.

Limit of Liability In the event of a breach of these Conditions of Sale or of any implied warranties, whether statutory or otherwise, or arising out of or in relation to the sale of Antelco products, Antelco's liability is limited to the repair or replacement of defective goods. In no event will such a breach give rise to any liability for punitive damages, loss of prots or expected future business, damage to reputation or goodwill, loss of any order or contract or any consequential or indirect loss or damage arising from any cause whatsoever.

Warranty Shortages or Damaged Goods Claims for shortages or errors on orders despatched will not be recognised after seven (7) days from the date of delivery. If goods are received damaged or the delivery is incomplete as per the packing slip, record details on the delivery note and advise the carrier and Antelco Pty Ltd immediately.

Force Majeure If by reason of any fact, circumstance, matter or thing beyond its reasonable control, Antelco Pty Ltd is unable to perform in whole or in part any obligation under these Conditions of Sale then Antelco Pty Ltd is relieved of that obligation to the extent and for the period that it is so unable to perform and is not liable to the customer in respect of such inability.

59

In addition to any statutory warranty and subject to these Conditions of Sale, Antelco Pty Ltd warrants that its products are of merchantable quality, free from defects or faults, and are t for the purpose for which they were manufactured or supplied. At its option and in its sole discretion, Antelco Pty Ltd will repair or replace goods found to be defective in workmanship or materials within twelve (12) months of the date of purchase. The customer will be responsible for delivering products to be repaired to Antelco Pty Ltd.

Applicable Law All matters for determination between Antelco Pty Ltd and the customer shall be determined by a court of competent jurisdiction in the State of South Australia according to the laws of South Australia.

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

Export Conditions of Sale: Antelco Pty Ltd Prices

Product Design

All prices set out in the Antelco Export Price List are in Australian dollars and are ex works, Murray Bridge, South Australia, Australia. Prices may change without notice and customers may conrm prices at the time of ordering.

Antelco Pty Ltd reserves the right to re-design its products and thereby cause changes to the specications, without notice and without incurring any liability.

Compatibility Payment Payment is required prior to despatch and may be made by VISA or MasterCard or by electronic funds transfer (contact Antelco Pty Ltd for bank details). Any fees and charges associated with the payment method are to be borne by the customer.

Orders

Antelco Pty Ltd is a manufacturer of irrigation products which are designed for use in outdoor irrigation applications only and low pressure systems where the operating pressure at the product does not exceed 300 kPa. Decisions on the use of Antelco products in any other situation remain the responsibility of the customer. If there is uncertainty as to the particular use of the product, the customer or end-user should test its suitability for that application.

Risk and Title

Orders will be accepted and invoiced at the prices in effect at the date of shipment. Antelco Pty Ltd reserves the right to change prices without notice.

Risk of loss or damage to the goods passes to the customer and/or the carrier at the time of despatch from Antelco Pty Ltd warehouse at Murray Bridge. Antelco Pty Ltd accepts no liability for goods lost or damaged in transit, and any carrier shall be deemed to be the agent of the customer. Goods held or stored for the customer shall be at the risk and expense of the customer, from the time at which the goods otherwise have been available for collection or despatch.

Notwithstanding that the risk of the goods may pass to the customer, Antelco Pty Ltd retains all legal and equitable rights of ownership of the goods until payment has been made in full (including interest and any other charges associated with the supply of the goods).

Freight and Insurance In addition to sea or air freight costs, customers will be charged for transport and any associated costs for delivery to an international departure point.

Goods are despatched uninsured and at the risk of customers who acknowledge that delivery insurance is their responsibility. Antelco can obtain insurance for customers on request.

CONDITIONS

Orders should be e-mailed to Antelco Head Ofce, Murray Bridge, South Australia.

Limit of Liability

Packaging All goods are packaged in export cartons in accordance with Antelco standard practice.

Shortages or Damaged Goods Claims for shortages or errors on orders despatched will not be recognized after seven (7) days from the date of delivery.

If goods are received damaged or the delivery is incomplete as per the packing slip, record details on the delivery note and advise the carrier and Antelco Pty Ltd immediately.

In the event of a breach of these Conditions of Sale or of any implied warranties, whether statutory or otherwise, or arising out of or in relation to the sale of Antelco products, Antelco's liability is limited to the repair or replacement of defective goods. In no event will such a breach give rise to any liability for punitive damages, loss of prots or expected future business, damage to reputation or goodwill, loss of any order or contract or any consequential or indirect loss or damage arising from any cause whatsoever.

Warranty

If by reason of any fact, circumstance, matter or thing beyond its reasonable control, Antelco Pty Ltd is unable to perform in whole or in part any obligation under these Conditions of Sale then Antelco Pty Ltd is relieved of that obligation to the extent and for the period that it is so unable to perform and is not liable to the customer in respect of such inability.

In addition to any statutory warranty and subject to these Conditions of Sale, Antelco Pty Ltd warrants that its products are of merchantable quality, free from defects or faults, and are t for the purpose for which they were manufactured or supplied. At its option and in its sole discretion, Antelco Pty Ltd will repair or replace goods found to be defective in workmanship or materials within twelve (12) months of the date of purchase. The customer will be responsible for delivering products to be repaired to Antelco Pty Ltd.

Returns

Applicable Law

Goods will be accepted for return only if prior approval has been obtained from Antelco Pty Ltd. The goods must be undamaged, unsoiled and in a saleable condition. All returned goods must include a copy of the original invoice and packing slip. Goods that are approved for return after thirty (30) days from the date of delivery are subject to a 15% restocking charge. Freight cost and risk will remain the responsibility of the customer.

All matters for determination between Antelco Pty Ltd and the customer shall be determined by a court of competent jurisdiction in the State of South Australia according to the laws of South Australia.

Force Majeure

Metric Cat. V1 170320

Antelco irrigation equipment metric catalogue 2020 www.antelco.com

60

Antelco Pty Ltd ABN 50 008 062 708 Head Ofce, Orders & Warehouse PO Box 246, Murray Bridge, SA 5253 A ustralia +61 8 8532 3388 murraybridge@antelco.com.au

Antelco Pty Ltd Sales & Marketing, Research & Development Unit 2 Angas House, 4-8 Angas St, Kent Town, SA 5067Australia +61 8 8334 4333 adelaide@antelco.com.au

Antelco Corporation Sales & Marketing, Orders & Warehouse 886 Waterway Pl, Longwood, Florida 32750 USA +1 407 331 0699 info@antelco.com

Antelco UK Limited Sales & Marketing, Orders & Warehouse 17a Chatmoor Rd, Leighton Buzzard, Bedfordshire LU7 4WG UK +44 152 585 9990 buzz@antelco.co.uk

www.antelco.com

PUTTING WATER WHERE IT COUNTS!®