DUNHAM PRICE LLC | WESTLAKE, LOUISIANA
Rear Pendants
Ball Valves
CTM
PART #
DESCRIPTION
SALE PRICE
715525
25’
$331
715533
15’
$331
715505
5’
$294
Poly Bridge Fenders
CTM / mtm PART #
DESCRIPTION
SALE PRICE
760092
1.5” Ball Valve
$40
760029
1.25” Ball Valve
$30
760003
1.0” Ball Valve
$20
760018
0.75” Ball Valve
$14
760036
0.5” Ball Valve
$11
Gauge - Slump
mtm
CTM / mtm PART #
DESCRIPTION
COLOR
SALE PRICE
790102
LH BLACK
$108
790100
RH BLACK
$108
790111
LH RED
$111
790110
RH RED
$111
790108
LH ORANGE
$116
PART #
DESCRIPTION
SALE PRICE
CTM / mtm
715530
25’
$331
PART #
DESCRIPTION
SALE PRICE
790109
RH ORANGE
$116
715538
15’
$331
760007
0-3000 psi
$86
790107
LH WHITE
$116
715535
5’
$294
760002
0-5000 psi
$86
790106
RH WHITE
$116
Pump - Parker, RH, New
745300 CTM / mtm
$698
Pump - Water, Air Diaphragm / Sandpiper
710260 CTM / mtm
$657
Con-Tech® Tool Box, Poly BLK 18” x 18” x 24”
790007 CTM / mtm
$281
Tool Box, Diamond Plated 18” x 18” x 24”
790001 CTM / mtm
$387
Con-Tech Manufacturing, Inc. reserves the right to limit quantities. · Prices valid 11/01/26 to11/30/26 · NOVEMBER 2026
KINGPIN INSPECTION INTERVALS
FIRST IN-SERVICE INSPECTION
Wheel Bearings - Verify end play is between 0.001” and 0.005”. Adjust and lubricate as required
Tie Rod Ends - Inspect for leaking and lubricate as required Kingpin Bushings - Check for wear and grease as required
Within the first 3,000 Miles
PREVENTATIVE MAINTENANCE 8,000 Miles or every 3 months, whichever comes first 10,000 Miles or every 6 months, whichever comes first 10,000 Miles or every 6 months, whichever comes first
Pivot Connections - Verify torque 5,000 Miles or as needed
Stabilizers - Check for leaking and adequate return Broke Assembly Components - Inspect for leaking and component wear
3,000 Miles
20,000 Miles or every 10 months, whichever comes first
LUBRICATION INTERVVALS Regular lubrication intervals should be followed to hellp prevent premature wear to the kingpin bushings.
GREASING AND LUBRICATION SPECIFICATIONS COMPONENT
GREASING INTERVAL
Kingpin Break In
5,000 Miles or as needed
Kingpin Bushing
10,000 Miles or every 6 months
KINGPIN LUBRICATION
On the Hendrickson suspensions, the kingpin grease fittings are located on the top and bottom of the kingpin grease caps. 1. Prior to greasing the kingpins, the axle must be on the ground in a loaded condition. 2. Clean off all the grease fittings (top and bottom of pin/steering knuckle) with a clean shop towel prior to lubrication. 3. Lubricate the kingpins through the grease fittings on the top and bottom of the pin/ steering knuckle. 4. Force the required lubricant into the upper and lower kingpin grease fittings until new lubricant flows from locations A and B, see Figure.
GREASE NLGI-1 or NLGI-2 NOTE: GREASING AT THE LOWER ZERK SHOULD PURGE GREASE FROM THE THRUST BEARING SHELL.
A B
Con-Tech Manufacturing, Inc. reserves the right to limit quantities. · Prices valid11/01/26 to 11/30/26 · NOVEMBER 2026
507-374-2239 | WWW.CTMMIXERS.COM