Issuu

$3.00

Published Nationally ®

Western Edition

July 19 2020 Vol. IX • No. 15

“The Nation’s Best Read Construction Newspaper… Founded 1957.” 470 Maryland Drive • Ft. Washington, PA 19034 • 215-885-2900 • Toll Free 800-523-2200 • www.constructionequipmentguide.com

Inside

Widening the Gap How KNA Is Improving a Major Colorado Highway

Holcombe Mixers Joins Border Construction...9

California-to-Las Vegas Rail to Run Along I-15...12

New materials for Kramer North America’s project will include 1.2 million cu. yds. of earthwork, 28,327 cu. yds. of reinforced concrete and 694,832 tons of asphalt.

By Irwin Rapoport Sennebogen 718 Continues to Crush Workload...15

CEG CORRESPONDENT

The Colorado Department of Transportation’s (CDOT) $350 million I-25 South Gap project,

awarded to Kraemer North America (KNA), is improving 18 mi. of highway south of Castle Rock (Douglas County, about 40 mi. south of Denver) to the town of Monument (El Paso County), with

a major component being the construction of an express lane in each direction to meet increased traffic demands. Work started in September 2018 and is slated for completion in

early 2022. Primarily financed by state funds, it also is being supported with contributions from Douglas and El Paso counties, Pikes Peak Rural Transportation Authority and see GAP page 28

Table of Contents ................4 Recycling Section ........15-23

House Passes Massive $1.5T ‘Moving Forward Act’

Attachments & Parts...29-33 By Lucy Perry

Truck & Trailer Section ........ ......................................39-40 Auction Section ..........42-45 Business Calendar ............44 Advertisers Index ..............46

CEG CORRESPONDENT

create millions of jobs while the construction industry plugs along during the COVID-19 pandemic and spring recession. “I’m particularly focused on investing in our roads, bridges, transit, rail and water systems,” Rep. Peter DeFazio (DOre.), chair of the House Transportation and Infrastructure Committee, said during Soil compactors work on an embankment on a high- the rules committee meeting.

The U.S. House of Representatives passed the $1.5 trillion Moving Forward Act, a massive funding package meant to regenerate America’s transportation infrastructure as it tries to give a shot in the arm to health care, airports, clean energy, broadband, education, and drinking water. On top of that, it would way construction project.

see BILL page 36

Page 2 â€˘ July 19, 2020 â€˘ www.constructionequipmentguide.com â€˘ CONSTRUCTION EQUIPMENT GUIDE

Par ts are only a click away. Order par ts is simple!

Keep track of your account status!

Request service, manage nage rentals,and quickly look up equipment inffo for par ts searches. lloo

Any One - Tiime P Parts Purchase up to $1,000 o on the 4Rivers Customer Por o ta t l with Code o â€˜Por o ttal10â€™ in â€˜Orrder Notesâ€™.

Unlock your phone,, and hover over thiss code with your cam mera to get started!

SAVE TIME â€˘ SAVE MONEY SAVE LABOR â€˘ SAVE OIL â€˘ â€˘ â€˘ â€˘ â€˘

No tools required No expensive hardware needed No more rags stuffed into hoses No more messy plastic caps The ultimate contamination control tool â€˘ One hand installation â€˘ Eliminate hydraulic oil spills & clean up â€˘ Quick installation & ease of usage â€˘ Safe for personnel & environment â€˘ Industry acclaimed â€˘ 100% Made in USA INTRODUCING FlangeLock Tool Boxes TM

4 Tool Boxes Available

All Include Slugs and O'Rings.

2QH FRXSRQ SHU FXVWRPHU RÎ? YDOLG RQ 5LYHUV &XVWRPHU 3RUWDO 3DUWV RUGHUV XS WR IRU PD[LPXP GLVFRXQW RI RÎ? RUGHU 2Î? 2 HU 9DOLG 0D\ WKURXJK 'HFHPEHU 6RPH UHVWULFWLRQV DSSO\ 6HH GHDOHU IRU GHWDLOV

For more information contact Mike Pearl at 914.980.8890 or email mike @ flangelock.com

www.flangelock.com

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 3

"In Business for over 33 Years" 2014 Dynapac CA2500D, Stk#: 12242, EROPS, A/C & Heat, 84" Smooth Drum, 1,403 hrs., Front & Rear Clear Out Bar, 23.1x26RS Tires @ 80%, Cumming Eng. ......................................$59,500

www.hendrixmachineryllc.com 1-936-327-5430 • Email: sales@hendrixmachineryllc.com

2018 Terex TLB840R, Stk#: 11556, OROPS,

Se Habla 4WD, New, 606 hrs., 24" Bucket, Ext-Hoe, Pilot Español Controls, 12x16.5 Front Tires, 500x70x24 Rear

Tires, 4 Cyl. Deutz Eng...........................$42,500

2013 Cat D6T LGP, Stk#: 12081, EROPS, A/C & Heat, Sweeps, Rear Screen, Available with St/Tilt Blade or Hyd. Angle Blade, 5,641 hrs., 36" Pads, with Allied Winch or Ripper ................$119,500

2016 Volvo SD115, Stk#: 12095, 84" Smooth Drum, 771 hrs., 23.1x26R3 Tires, 4 Cyl. Volvo Eng ........................................................$59,500

1990 Grove RT745, Stk#: 12055, 45 Ton, 4WD, 2012 JCB VM75D, Stk#: 12285, OROPS, 54" Main Boom of 104' for a maximum tip height of 2015 Komatsu PC210LC-10, Stk#: 12256, 165' (50.3) 12 hrs., 26.5x25 Tires, 8 Cyl. Eng....... EROPS, A/C & Heat, FM Stereo, 3,567 hrs., 36" Smooth Drum w/Pad Shell Kit, 1,788 hrs., ................................................................$49,500 Bucket, Aux. Hyd., 32" Pads, 10' 5" Wide$79,500 14.9x24 Tires ........................................$34,500

2016 John Deere 700K, Stk#: 12354, EROPS, A/C & Heat, 6 Way Blade ......................$98,500

2015 Cat D6T LGP, Stk#: 12024, EROPS, A/C & Heat, Available with St/Tilt Blade or Hyd. Angle Blade, 5,525 hrs., 36" Pads, with Paccar Winch or Ripper ....................................................$129,500

2017 John Deere 160G, Stk#: 12344, EROPS, 2016 SunWard SWE210F, Stk#: 12277, EROPS, A/C & Heat, AM/FM Radio, 3,485 hrs., 42" A/C & Heat, FM Stereo, 20 hrs., 48" Bucket, Aux. Bucket, 10' 3" Stick, 27" Pads, 80% U/C, Rear Hyd., 24" Pads, Izuzu Eng., 9' 2" Wide ..$89,500 Camera, 8' 9" Wide ................................$82,500

2010 Daewoo G25E-3, Stk#: 12047, 6,000 lbs., 15 ft., 4,388 hrs., 40" Forks, 48" Frame, 3 Stage Mast, 7.00x15 Front Tires, 6.50x10 Rear Tires, Propane, wt 9,568 lbs. ............................$9,500

2018 John Deere 450K LGP, Stk#: 12290, EROPS, A/C & Heat, Sweeps, Rear Screen, AM/FM Radio, 6 Way Blade, 569 hrs., 9' 6" Wide ..............................................................$86,500

2019 Cat D5K2 XL, Stk#: 12297, EROPS, A/C & Heat AM/FM Radio, 6 Way Blade, 448 hrs., 24" Pads, System One U/C, Grade Control, Long Track Frame, Cat. Eng., 8 ft. Wide ........126,500

2011 Cat TL12-55, Stk#: 11996, EROPS, A/C & Heat, 12,000 lbs., 55 ft., 6,747 hrs., 60" Forks, 74" Frame, Aux. Hyd., 400x75x28 Tires, 4 Cyl. Cat Eng. ................................................$52,500

2013 JLG /Skytrak 10054, Stk#: 11916, 10,000 2014 Morooka MST1500VD, Stk#: 12291, lbs., 54 ft., 7,247 hrs., 60" Forks, 74" Frame, 2007 JLG 600A, Stk#: 12144, OROPS, 2,346 hrs., EROPS, A/C & Heat, 2,651 hrs., 26" Rubber 400x75x28 Foam Filled Tires, 4 Cyl. Cummins Eng 355x55Dx625 Foam Filled Tires, 4 Cyl. Deutz Eng.. Tracks @ 80%........................................$59,500 ................................................................$46,500 ................................................................$22,500

2013 JLG G12-55A, Stk#: 11883, EROPS, 12,000 lbs., 55 ft., 6,362 hrs., 48" Forks, 52" Frame, 4WD, 400/75- 28 Tires, 4 Cyl. Cummins Eng.........................................................$56,500

2012 Skytrak 10054, Stk#: 11990, 10,000 lbs., 54 ft., 7,019 hrs., 60" Forks, 74" Frame, Aux. Hyd., 400x75x28 Foam Filled Tires, Hyd. Self Leveling System, 4 Cyl. Cummins Eng. $46,500

2017 Cat 299D2, Stk#: 12331, OROPS, 1,521 hrs., Aux., Hyd., 18" Rubber Tracks, Manual Quick Connect, 48" Carriage, 48" Forks, Standard Flo Only ..................................$39,500

1990 Bomag MPH100R, Stk#: 11897, OROPS, 1,248 hrs., 11.25x24 Front Tires, 28Lx26 Rear Tires, 8 Cyl. Detroit Eng ..........................$32,500

2013 Atlas Copco QAS90, Stk#: 12088, 6,135 hrs., ST205x75Rx15 Tires, JD Eng. ........$19,500

2014 Hyundai 160D-7E, Stk#: 12174, EROPS, A/C & Heat, 35,274 lbs. Lift, 13 ft., 7,384 hrs., Rear Camera, Side Shift Carriage, 12.00x20 NHS 2012 Genie S40, Stk#: 12108, 500 lbs., 40 ft., 2010 JGL 600AJ, Stk#: 12135, 500 lbs., 60 ft., 2,759 hrs., 12x15.5 Foam Filled Tires, 3 Cyl. 2,358 hrs., 35x55Dx625 Tires, 4 Cyl. Deutz Eng. .. Tires @ 80%, Cummins QSB 6.7 Eng., wt. ................................................................$29,500 43,265 lbs..............................................$79,500 Deutz Eng...............................................$22,500

2015 Cat 930K, Stk#: 12323, EROPS, A/C & Heat, AM/FM Radio, 7,810 hrs., Cat Bucket, 20.5Rx25 Tires @ 80%..........................$59,500

2015 Toyota 8FGU25, Stk#: 12282, 15 ft., 1,993 Hrs., 40" Forks, 3 Stage Mast, Side Shift, 7.00x 12 Front Tires, 6.00x9 Rear Solid Tires, Duel Fuel Propane/Gas ..........................$19,500

2016 Haulotte HT132RTJ Pro, Stk#: 11372, 500 lbs., 132 ft., 81 hrs., 4WD, 8ft. Man Basket, JIB, 2010 JLG 600AJ, Stk#: 12136, 500 lbs., 60 ft., Straight Boom, 445x65Dx22.5 Foam Filled Tires, 2006 Case 325, Stk#: 12007, EROPS, A/C & Heat, 2,912 hrs., 355x55Dx625 Tires, 4 Cyl. Deutz 4 Cyl. Perkins Diesel Eng ........................$59,500 5,489 hrs., 650x65Rx25 Tires..................$66,500 Eng.........................................................$29,500

2010 John Deere 6330, Stk#: 11394, OROPS, Sweeps, Front & Side Screens, 6,440 hrs., 4WD, 793x535x511 Front Tires, 345 LS-2 Rear Tires, 4 Cyl. JD Eng. ..........................................$29,500

2018 Genie GTH2506, Stk#: 11376, EROPS, 2014 Cat 329EL, Stk#: 12210, EROPS, A/C & Heat, 3 hrs., 5,500 lbs., 19 ft., 4WD, 4WS, 48" Heat, FM Radio, 4,768 hrs., 36" Bucket, Aux. Hyd., Frame, 48" Forks, Aux. Hyd., 12x16.5 Tires, 4 30" Pads, 9' 6" Stick ................................$92,500 Cyl. Deutz Eng. ........................................$56,500

2012 JLG 400S, Stk#: 12161, 500 lbs., 40 ft., 3,296 hrs., Foam Filled Tires @ 75% ......$26,500

2015 Doosan G25E5, Stk#: 12280, 15ft., 1,559 Hrs., 40" Forks, 3 Stage Mast, 7.00x15x5.50 Front Tires, 6.50x10 Rear Tires, Duel Fuel Propane/Gas ..........................................$19,500

2012 Laymor SM300, Stk#: 12093, 813 hrs., 8 ft. Broom, 3 Wheel, ST205x75Rx14 Tires, 4 Cyl. Kubota Eng...............................................$14,500

Page 4 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

FEATURES

IN THIS ISSUE 9

David Deem, president of Deem Structural Services, Longview, Texas, and Bob Beckner, retired Senior Vice President of Peterson Beckner Industries Inc., Dallas, Texas, recently were honored by the Steel Erectors Association of America.

COURT RULING PUTS KEYSTONE PIPELINE CONSTRUCTION ON HOLD

The U.S. Supreme Court handed another setback to the Keystone XL oil sands pipeline from Canada on July 6 by keeping in place a lower court ruling that blocked a key environmental project permit. Canadian company TC Energy needs the permit to continue building the pipeline in the U.S.

HOLCOMBE MIXERS JOINS MASSIVE BORDER CONSTRUCTION

Holcombe Mixers, a provider of volumetric concrete mixers and strategic solutions for the concrete industry, teamed up with Fisher Sand and Gravel and Cat Construction to fast-track the major border wall construction project along Arizona’s southern border.

PACIFIC HOSPITALITY GROUP, MORTENSON CONSTRUCTING HYATT

Amid the rapidly changing landscape and a recovering Arizona economy, Pacific Hospitality Group and Mortenson recently broke ground on a 238-room, eight-story Hyatt Place hotel in downtown Phoenix. The new hotel is scheduled to open in September 2021.

PARTNERSHIP ALLOWS ACCESS TO WATER DATA FOR RENOVATIONS

A partnership with the U.S. Geological Survey’s Arizona Water Science Center is helping ADOT engineers anticipate the effects of extreme weather on bridges and highways and design ways to handle it. Since 2014, ADOT's use data involving flooding, natural hazards and weather-related risks has improved.

HIGH-SPEED TRAIN BETWEEN SO. CALIF., LAS VEGAS TO BE BUILT ALONG I-15

A plan to build a high-speed train between southern California and Las Vegas got a boost after the rail company in charge of the project received permission to build along Interstate 15. XpressWest entered into a lease agreement with the California Department of Transportation to construct the rail line.

Founder, Publisher & CEO Western Publisher Executive Publisher Editor In Chief Senior Editor Editorial Assistant Editorial Consultant Production Mgr. Controller Circulation Mgr.

Edwin M. McKeon Sr. Dennis Hogeboom Teddy McKeon Craig Mongeau Robby Chakler Katherine Devlin Pete Sigmund John Pinkerton Judith Nixon Cathy Printz

www.constructionequipmentguide.com Advertising e-mail production@cegltd.com

Mobile

Facebook

Twitter

HOW VERMEER’S ANDRINGA BECAME HER COMPANY’S FIRST WOMAN IN AEM HOF

One mile across, seven facilities, and the need to grow their Pella, Iowa, plant physically to meet demand in a new market is where Mary Andringa found the company founded by her father, Gary Vermeer. That’s when she was challenged by a board member to think about the problem sustainably.

OSHA ISSUES ITS NEW SILICA STANDARDS GUIDANCE

The U.S. Department of Labor’s Occupational Safety and Health Administration (OSHA) recently issued a compliance directive designed to ensure uniformity in inspection and enforcement procedures when addressing respirable crystalline silica exposures in general industry, maritime, and construction.

ENGAGING POLICYMAKERS IN RESPONSE TO COVID-19 PANDEMIC

Knowing how much our industry is doing, and will need to continue to do to help rebuild our economy, it’s also important that we all tell our elected officials what is needed to keep our industry safe while maintaining a high level of production. There’s no better time to do that than right now.

MACK, ATA TEAM UP WITH ALAN TO DELIVER VITAL AID, GOODS

To assist those impacted by the coronavirus pandemic, Mack Trucks and the American Trucking Associations (ATA) are partnering with the American Logistics Aid Network (ALAN) to deliver vital supplies, such as food and personal-care items, to nonprofit organizations who distribute these goods locally.

MACK DEFENSE HEADQUARTERS RELOCATES TO CUSTOMER CENTER

To better serve customers, as well as enhance its capability to support military and government contracts, Mack Defense has relocated its headquarters to the Mack Customer Center (MCC) located in Allentown, Pa. The move also provides Mack Defense additional working space and access to other MCC amenities.

RITCHIE BROS.’ BUSY WEEK SETS NEW RECORDS

RECYCLING SECTION

15 16 20

SENNEBOGEN 718 ‘FORCE MULTIPLIER’ CRUSHES WORKLOAD MB CRUSHER HELPS CROATIAN TOWN LAY NEW WATER PIPES

CAT MH3040 MATERIAL HANDLER CUTS FUEL BY UP TO 25 PERCENT

DEPARTMENTS

42 44

COMING AUCTIONS BUSINESS CALENDAR

29 30 32 40

FECON Blackhawk Mulcher Head CALDWELL GROUP Mill-Duty Coil Grab ALLU Transformers Attachments FELLING IT-I Tilt

EQUIPMENT

For advertising rates Contact

Main office 470 Maryland Drive Fort Washington, PA 19034 215/885-2900 Toll Free 800/523-2200 Fax 215/885-2910 Web site

Circulated Throughout

• Alaska • Arizona • California • Colorado • Hawaii • Idaho • Montana • New Mexico • Nevada • Oklahoma • Oregon • Texas • Utah • Washington • Wyoming

To read these stories and many more, visit www.constructionequipmentguide.com

SEAA: PERSON OF THE YEAR, LIFETIME ACHIEVEMENT AWARDS

WESTERN EDITION

YouTube

Dennis Hogeboom

Kent Hogeboom

Patrick Kiel

Debbie Hansen

• Colorado• Louisiana • Oklahoma • Texas • New Mexico

National Sales Manager

• Idaho • Montana • Oregon • Washington • Wyoming

• Arizona • California • Nevada • Utah

Cell e-mail

952/353-1770 612/481-8557 Cell e-mail pkiel@cegltd.com

Cell e-mail

602/679-8759 dennishogeboom@cegltd.com

315/866-1423 518/221-5159 khogeboom@cegltd.com

Construction Equipment Guide Western Edition (ISSN 2330-9792) is published bi-weekly by Construction Equipment Guide Ltd. Advertising and Editorial Offices are located at 470 Maryland Dr., Ft. Washington, PA 19034. Toll Free 800/523-2200 or Fax 215/885-2910. Annual Subscription Rate $65.00. Call for Canadian and foreign rates.

the publisher. All editorial material, photographs, drawings, letters, and other material will be treated as unconditionally assigned for publication and copyright purposes and are subject to Construction Equipment Guide's unrestricted right to edit and comment editorially. Contributor articles do not necessarily reflect the policy or opinions of this publication.

Periodicals postage paid at Ft. Washington, PA and at additional mailing offices. POSTMASTER: Send address changes to Construction Equipment Guide Western Edition, 470 Maryland Dr, Ft. Washington, PA 19034.

Call or write for advertising rates, publication schedule and media kit. The Construction Equipment Guide is not responsible for clerical or printer's errors, every care is taken to avoid mistakes. Photographs of equipment used in advertisements are not necessarily actual photographs of the specific machine. Similar photographs are used occasionally and every effort is taken to depict the actual equipment advertised. The right is reserved to reject any advertising.

Contents Copyrighted ©2020, by Construction Equipment Guide, which is a Registered Trademark, registered in the U.S. Patent Office. Registration number 0957323. All rights reserved, nothing may be reprinted or reproduced (including framing) in whole or part without written permission from

702/239-0348 dhansen@cegltd.com

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 5

A FULL LINE OF EQUIPMENT & PRODUCT SUPPORT SOLUTIONS FOR ALL YOUR ROAD BUILDING NEEDS. We don’t build roads. We make the equipment so you can cost-effectively build and maintain the world’s roads. With the Roadtec heavy-duty design, we are able to keep your machine working longer while lowering maintenance and operating costs. We also make your operators more comfortable and confident with our user-friendly design and our customization for special projects.

www.roadtec.com

1.800.272.7100

PACWEST MACHINERY

POWER MOTIVE CORP.

www.pacwestmachinery.com

www.powermotivecorp.com

8207 South 216th Street Kent, WA 98032 800-935-5933

19255 NE Sandy Blvd Portland, OR 97230 800-929-5933

3515 N Sullivan Road Spokane Valley, WA 99216 800-938-5933

1550 Irving Road Eugene, OR 97402 866-920-5933

5000 Vasquez Blvd. Denver, CO 80216 303-355-5900 Colorado Springs, CO 719-576-5541

+1.423.265.0600

Grand Junction, CO 970-241-1550

Durango, CO 970-259-0455

Milliken, CO 970-587-1188

Cheyenne, WY 307-634-5149

Page 6 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

EVERYTHING YOU NEED. Contact our distributors and find out how we can help improve your bottom line. Visit info.terex.com/distributorsearch to find your local distributor.

BIGGE CRANE AND RIGGING

SCOTT-MACON EQUIPMENT

(RT) www.bigge.com

(RT) www.smequipment.com

San Leandro, CA 888-337-2444 510-638-8100

14925 South Main Street Houston, TX 77035 713-721-7070 Fax: 714-721-0422

San Jose, CA 408-452-1537 La Mirada, CA 714-670-9525 Auburn, WA 206-443-8500

For Your Local Terex Dealer Please Contact: Terex USA, LLC 9528 West Interstate 40 Service Road Oklahoma City, Oklahoma 73128 USA Phone: (877) MY-TEREX email: info.cranes@terex.com web: www.terex.com/cranes

Dallas, TX 214-391-4000 Corpus Christi, TX 361-289-2782 Houma, LA 985-851-1118 Baton Rouge, LA 225-753-4111 Tulsa, OK 918-224-2000

Authorized Distributor Cranes © Terex Cranes 2019. Terex and the Terex Crown design are trademarks of Terex Corporation or its subsidiaries.

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 7

MORE M POOWERR reliable, undeniable performanc ce. With Doosan Portable Power e on your side, you can Make Power Moves. See the full lineup at DoosanPowerMoves.com/Portab blePower.

Air Compressor Solutions, Inc.

Ditch Witch of Arizona

Ditch Witch of Southern Arizona

www.acsir.com

www.ditchwitchaz.com

Odessa (432) 335-5900 Amarillo (806) 383-1213

Phoenix (602) 437-0351

Tucson (520) 579-0261

TEXAS

ARIZONA

Sierra Machinery, Inc. www.sierraelpaso.com

TEXAS

El Paso (915) 772-0613

NEW MEXICO Artesia (575) 746-6592

Volvo Construction Equipment & Services www.vcesvolvo.com

CALIFORNIA

Bakersfield (661) 387-6090 Fresno (559) 834-4420 San Leandro (510) 357-9131 Sacramento (916) 388-2244

San Diego/ Lakeside (619) 441-3690 Corona (951) 277-7620

MAKE POWER MOVES.

Papé Material Handling Inc.

OREGON

Portland (503) 639-8910 Portland (503) 286-6400 Eugene (541) 689-7407 Medford (541) 779-3444

www.papemh.com

NEVADA

Sparks (775) 356-9333

WASHINGTON Seattle (206) 722-5800 Arlington (360) 474-8461 Fife (253) 926-4386

Bellingham (360) 756-6572 Yakima (509) 248-5636 Pasco (509) 545-1959 Wenatchee (509) 884-2934 Spokane (509) 536-7300

Page 8 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

SEAA: Person of the Year, Lifetime Achievement Awards David Deem, president of Deem Structural Services, Longview, Texas, and Bob Beckner, retired Senior VP of Peterson Beckner Industries Inc., Dallas, Texas, recently were honored by the Steel Erectors Association of America. Deem was named SEAA’s 2019 Person of the Year, and Beckner, who recently stepped down from the SEAA board of directors in anticipation of retirement, was honored with a Lifetime Achievement award. “David Deem is a strong advocate for the advanced of industry quality and safety standards. In addition to work with our organization, he also actively works to educate personnel through AISC and NISD programs,” said Tom Underhill, executive director. Among the technical publications he has assisted in writing are the Detailing Steel for Value and Safety and Detailing Guide for the Bob Beckner (R) of Peterson-Beckner Industries receives a Enhancement of Erection Safety. Lifetime Achievement award from SEAA President Geoff Kress. In addition, he has been a featured speaker representing steel erectors Industry representative. Advanced Certified Steel Erector. at the North America Steel “David Deem is a man of few Previously, Deem operated Deem Conference. words, but when he speaks, he is Steel Erectors, East Texas Erectors, Deem has been active in SEAA insightful and direct,” said and was vice president of operasince 1995, and served on the Underhill. tions of Peterson-Beckner Industries. board of directors at various times. Founded in 2013, Deem Bob Beckner, recipient of a He currently is the vice president, Structural Services is an AISC Lifetime Achievement award,

David Deem (L) of Deem Structural Services receives the Person of the Year award from SEAA President Geoff Kress.

served on the SEAA board of directors for 27 years. “Bob Beckner is a selfless man who has given countless hours to our industry and organization,” said Josh Cilley, president of American Steel & Precast Erectors.

Beckner is a past president of SEAA and recipient of the William Davis Service Award. He also has served on numerous AISC committees over the years. For more information, visit www.seaa.net. 

Court Ruling Puts Keystone Pipeline Construction on Hold BILLINGS, Mont. (AP) The U.S. Supreme Court handed another setback to the Keystone XL oil sands pipeline from Canada on July 6 by keeping in place a lower court ruling that blocked a key environmental project permit. Canadian company TC Energy needs the permit to continue building the long-disputed pipeline across U.S. rivers and streams. Without it, the project that has been heavily promoted by President Donald Trump faces more delay just as work on it had finally begun this year following years of courtroom battles. The recent Supreme Court order also put on hold an earlier court ruling out of Montana as it pertains to other oil and gas pipelines across the nation. That’s a sliver of good news for an industry that just suffered two other blows — the recent cancellation of the $8 billion Atlantic Coast gas pipeline in the Southeast and another ruling that shut down the Dakota Access oil pipeline in North Dakota. In the Keystone case, an April ruling from U.S. District Judge Brian Morris in Montana had threatened to delay not just Keystone but more than 70 pipeline projects across the U.S., and add as much as $2 billion in costs, according to industry representatives. Morris agreed with environmentalists who contended a

U.S. Army Corps of Engineers construction permit program was allowing companies to skirt responsibility for damage done to water bodies. But the Trump administration and industry attorneys argued the permit, in place since the 1970s, was functioning properly when it was cancelled by Morris over concerns about endangered species being harmed during pipeline construction. The corps suspended the program following Morris’ April ruling. Agency officials could not be immediately reached for comment. TC Energy spokesman Terry Cunha said the company is not giving up on Keystone, but it will have to delay large portions of the 1,200-mi. (1,900-km) oil sands pipeline. The company started construction last month on a 329-mi. (530km) section of the line in Alberta. That work will continue while the company wages its court fight in the U.S., Cunha said. An attorney for one of the environmental groups involved in the case called the recent order a major victory in the fight against Keystone. But he acknowledged the plaintiffs had hoped to hamper oil and gas projects nationwide. “Our focus was originally on Keystone, so we’re very happy the court order ensures it can’t move forward under

this unlawful permit,” said Jared Margolis, an attorney with the Center for Biological Diversity. Pipeline industry representatives said the order means thousands of workers whose jobs were threatened can continue working. A coalition of 18 states had backed the Trump administration in the case. West Virginia Attorney General Patrick Morrisey said the Supreme Court’s action “ensures that one Montana district court judge doesn't possess the power to drive national policy on such a critical issue.” The order returns the case to the U.S. 9th Circuit Court of Appeals for further consideration. Keystone was proposed in 2008 and would carry up to 830,000 barrels (35 million gallons) of crude daily to Nebraska, where it would be transferred to another TC Energy pipeline for shipment to refineries and export terminals on the Gulf of Mexico. TC Energy’s surprise March 31 announcement that it intended to start construction amid a global economic crisis caused by the coronavirus pandemic came after the provincial government in Alberta invested $1.1 billion to jump-start the work. The company finished building the first piece of Keystone XL across the U.S. border in late May and started work on labor camps in Montana and South Dakota. 

ARIZONA STATE EDITION

A Supplement to:

“The Nation’s Best Read Construction Newspaper… Founded in 1957.” Your Arizona Connection – Debbie Hansen – 1-702-239-0348 – dhansen@cegltd.com

Holcombe Mixers Joins Massive Border Construction Holcombe Mixers, a provider of volumetric concrete mixers and strategic solutions for the concrete industry, teamed up with Fisher Sand and Gravel and Cat Construction to fast-track the major border wall construction project along Arizona’s southern border. Holcombe Mixers was chosen as a partner by Fisher due to its combination of operational experience, advanced technology and their volumetric concrete mixers’ extensive payload capacity. “Working with Holcombe Mixers has been a game changer,” said Tommy Fisher, president and CEO of Fisher Sand and Gravel. “We made a commitment to President Trump, the Department of Homeland Security and the US Army Corps of Engineers to get the wall up faster, and do it financially smarter. Generally, you’re Holcombe Mixers, crews can pour 20-to-25 loads of pouring 2-to-5 loads per day. With With fresh concrete each day and not have to worry about it Holcombe Mixers, we can pour 20- exceeding required temperatures. to-25 loads of fresh concrete each day and not have to worry about it exceeding required temperatures.” Pouring high volumes of concrete in remote areas with hot and arid climates like Arizona’s creates extreme challenges to mitigate the concrete from setting up too quickly when mixed in a traditional drum mixer. Volumetric mixers from Holcombe are able to mix fresh concrete on site at the point of the pour. The low- and high ad-mixture systems add an addiBrent Holcombe tional layer of flexibility to ensure that Holcombe Mixers the concrete being produced can be

placed and finished in any extreme condition. “An element of control is key for a project that demands not only durability, but also the volume of fresh concrete that needs to be poured 16 hours a day,” said Brent Holcombe, managing partner of Holcombe Mixers. “Our 12-yard aggregate bins have supported a 120 percent increase to the standard payload where daily concrete pour goals can be achieved and ultimately surpassed. We are thrilled to be part of this visionary team effort.” Pouring and placing concrete is as much an art form as excavation. The collaboration with Cat Construction will be beneficial for all involved. see MIXERS page 11

“An element of control is key for a project that demands not only durability, but also the volume of fresh concrete that needs to be poured 16 hours a day.”

“Working with Holcombe Mixers has been a game changer,” said Tommy Fisher, president and CEO of Fisher Sand and Gravel.

Page 10 • July 19, 2020 • www.constructionequipmentguide.com • Arizona State Section • Construction Equipment Guide

Top Quality Water Trucks We Deliver Worldwide!

156 E. Mohave Street Phoenix, AZ 85004

(602) 437-3980 www.SuperiorEquipmentInc.com

Warranty Financing Available

2019 International DuraStar 4300 2015 Peterbilt 337 Stock# 15H43WT, 2K tank Stock# 19F20WT, 2K tank

2018 International DuraStar 4300 Stock# 18F24WT, 2K tank

Call for Pricing (602) 437-3980

Trade-Ins Accepted

Parts

Add-Ons Available 2011 International 4300 Stock# 11D63WT, 2K tank

2004 Ford F650 Stock# 04K67WT, 2K tank

Various 2016-2020 Cabs & Chassis

Pacific Hospitality Group, Mortenson Constructing Hyatt Amid the rapidly changing landscape and a recovering Arizona economy, Pacific Hospitality Group and Mortenson recently broke ground on a 238-room, eight-story Hyatt Place hotel in downtown Phoenix. Pacific Hospitality Group, in partnership with Mortenson, is developing the project. Mortenson is providing development services and is the design-builder with Allen+Philp Partners, the designer. Pacific Hospitality Group will own and manage the hotel. “The construction of the Hyatt Place Hotel across the street from Phoenix City Hall is a testament to confidence in the resiliency of the Phoenix economy,” Christine Mackay, director of Phoenix community and economic development, said in an interview. “This exciting development is needed to add rooms to the city’s hospitality inventory, and it’s a statement that Phoenix is a strong market. It’s the rare economic developer who can look out her window and see rapidly-occurring

changes in a downtown landscape. From my vantage point, I am able to see eight cranes working to add high-rise buildings to downtown Phoenix. There are a half-dozen more I can’t see, but know are keeping construction workers busily employed,” she added. Opening in September 2021, the Hyatt Place Phoenix Downtown will bring the brand’s intuitive design, casual atmosphere and practical amenities, such as free Wi-Fi and 24-hour food offerings, to the Phoenix area. The hotel’s design will emulate the art deco design of the surrounding architecture, located adjacent to the Orpheum Theater. In the heart of downtown Phoenix, the hotel is just three blocks away from the Phoenix Convention Center and nearby to an array of downtown Phoenix attractions like Chase Field, Talking Stick Resort Arena, Phoenix Art Museum, shopping and restaurants. The new facility will be only just a few miles away from Phoenix Sky Harbor Airport. “Now more than ever, Pacific

The hotel is just three blocks away from the Phoenix Convention Center and nearby to an array of downtown Phoenix attractions like Chase Field, Talking Stick Resort Arena, Phoenix Art Museum, shopping and restaurants.

Hospitality Group is very excited to add our first Hyatt Place to our portfolio and our second hotel asset in Arizona,” said Garrett Busch, vice president of Capital Markets for Pacific Hospitality Group. “Our family has been in the hotel business for more than 30 years and we see this development

as a testament to our commitment to our team members, guests and communities that our industry will come back from the devastation of Covid-19. We are especially committed to the Arizona market and our budding relationship with the Hyatt brand. The Arizona market, specifically downtown, is a top

development market for PHG. We see a lot of potential in the economic diversity of the area, as well as the ASU presence and the scale of offerings in sporting and social events. “When seeking out a brand for this project, Hyatt was an obvious choice. Hyatt brings a longstanding tradition in excellence in hospitality; and the strength in their loyalty platform, World of Hyatt, will bring value to the diversity of offerings in the area.” Busch stated. “Similarly, we could not be more pleased to be partnering with Mortenson on this exciting project. Our partnerships with Mortenson and our long-time lending partner American National Insurance Company, especially in these times, have made this project possible. While this is our first project with Mortenson, this is our 7th ground up development with American National Insurance Company, among many other acquisition financings and refinancing’s over our 20+ year relationship.” 

Construction Equipment Guide • Arizona State Section • www.constructionequipmentguide.com • July 19, 2020 • Page 11

Pros Kno Pros Kno ow! w!

T Those in the know w,, know Takeuchi Take euchi

Takeuchi of o ffers a wide range of compact excavatorss to help you get your tougheest tasks comppleted. PUT A TAKEUCH A HI TO WORK ON O YOUR JOBSITE AN ND EXPERIIENCE THE DIFFEREN NCE!

www.ditchwitchaz.com

4028 S 36th Street Phoenix, AZ 85040 (602) 437-0351 6975 N Camino Martin Tucson, AZ 85741 (520) 579-0261

takeuch hi us.com hi-us.com

Partnership Allows Access to Water Holcombe Mixers, Cat Data for Bridge, Road Renovations Partner at the Border A partnership with the U.S. Geological Survey’s ments to U.S. 160 bridge spanning Laguna Creek on Arizona Water Science Center is helping Arizona the Navajo Nation in northeastern Arizona. The projDepartment of Transportation engineers anticipate the ect, which won an award from Arizona State effects of extreme weather on bridges and highways University’s Metis Center for Infrastructure and Sustainable Engineering, used data on the volume and and design ways to handle it. Since its start in 2014, this collaboration has velocity of the creek’s flow to anticipate how the channel will change. evolved to improve The resulting project proADOT's use data tected the bridge’s abutments involving flooding, natby using gabion baskets, ural hazards and weath- “These data have already which are metal cages filled er-related risks through with rocks, to reduce meanthe agency’s Resilience made a difference on dering where the creek passProgram. es under U.S. 160. “With U.S. numerous ADOT projects.” According to USGS Geological Survey’s Arizona Water Science expertise in water sciSteven Olmsted Center hydrologist Brandon ence and hydrology, ADOT Environmental Planning Forbes, “this partnership has ADOT can now use also established a successful these data to construct framework for collaboration and maintain bridges and roadways that better reflects how the natural envi- between USGS and State DOTs, and is being adopted ronment and highway infrastructure interact,” said by many other USGS offices across the country.” ADOT’s goal is to develop an end-to-end engineerSteven Olmsted, program manager with ADOT environmental planning. “These data have already made a ing-based process that will incorporate extreme weather and climate adaptation into the design of highway difference on numerous ADOT projects.” An example of this partnership is 2017 improve- and bridge projects. 

MIXERS from page 9

When machines break ground, they channel precision, efficiency and operational productivity. Border Wall Contract Announcement In May, Republican U.S. Sen. Kevin Cramer of North Dakota confirmed the $1.3 billion contract for building the 42-mi. section of wall through “really tough terrain in the mountains” in Arizona. That’s about $30 million per mile. The U.S. Army Corps of Engineers said that there was no set date for the completion of construction on the latest award. Construction will take place near Nogales, Ariz., and Sasabe, Ariz. The Arizona Daily Star first reported news of the contract. About Holcombe Mixers’ HM12H Volumetric Concrete Mixer Holcombe Mixers’ HM12H heavy duty volumetric concrete mixer is supported by the concrete industry’s only patented removable cassette conveyor that allows for belt changes in as little as five hours. Projects can stay on schedule with minimal downtime while saving horsepower and fuel with a frictionless conveyor roller floor and no-lubrication pintle conveyor chain that provides thousands of yards of service. With a load sensing variable displacement hydraulic system, system temperatures are reduced and the life of components are extended. To learn more visit holcombemixers.com 

Page 12 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Satisfaction Guaranteed! SEAL SAVER PROTECTIVE CYLINDER COVER KOMATSU D65EX-15

Made in the USA

The SEAL SAVER WILL: Protect cylinders from the elements • Eliminate dings and dents from falling debris • Reduce particle contamination of hydraulic systems • Prevent pitting due to chemical washes • Extend the life of cylinder seals • Eliminate rod scoring

STOP the never ending cycle of cylinder repairs. SEAL SAVER has proven effective in Construction, Mining, Waste Management, Quarries, Refineries, Marinas, Recycling, Wood Products Processing, Steel Mills and Hot Slag Industries. Exclusively manufactured by:

Fluid Control Services, Inc. 1155 Allgood Road • Suite 15 Marietta, GA 30062

1-800-683-5189 Fax: 770-509-5832

Visit

www.sealsaver.com

for more information or contact us at 1-800-683-5189

All Aboard...

High-Speed Train Between Southern Calif., Las Vegas to Be Built Along I-15 LOS ANGELES (AP) A plan to build a high-speed train between southern California and Las Vegas got a boost after the rail company in charge of the project received permission to build along Interstate 15. XpressWest entered into a lease agreement with the California Department of Transportation to construct the rail line on I-15’s median, Caltrans announced in a news release. Approximately 135 mi. (217 km) of the 170-mi. (274-km) rail system will be in California. “This will transform transportation in Southern California and Las Vegas for generations by providing a fast and efficient connection that gets people out of their cars, reduces traffic congestion, and decreases air pollution,” said Fiona Ma, California state treasurer. The project will be privately financed and will cost about $7 billion, according to 2018 estimates.

CALIFORNIA

IDAHO

HOLT OF CALIFORNIA www.holtca.com Pleasant Grove 916-921-8969

WESTERN STATES EQUIPMENT COMPANY www.westernstatescat.com Caldwell • 208-350-6334 Hayden • 208-762-6690 Idaho Falls • 208-552-2287 Lewiston • 208-746-3301 Meridian • 208-888-2287 Pocatello • 208-232-2640 Twin Falls • 208-734-7330

COLORADO WAGNER EQUIPMENT CO. www.wagnerequipment.com Aurora 303-739-3000 Denver 303-433-2727 (Rental) Carbondale 970-963-7368 (Rental) Commerce City 303-286-2300 (Rental) Colorado Springs 719-390-7316 (Rental) 719-635-1669 Granby 970-328-2080 (Rental) Gypsum 970-328-2080 (Rental) Hayden 970-276-3781 Silverthorne 970-262-3788 (Rental) Fort Collins 970-493-5005 (Rental) Grand Junction 970-245-6546 (Rental) 970-242-2834 Pueblo 719-544-0088 (Rental) 719-544-4433 Steamboat Springs 970-871-1990 (Rental) Windsor 970-278-1750 (Rental) Burlington 719-346-7880 (Rental) (719) 346-5132 Durango 970-259-2001 (Rental) 970-259-2001 Windsor 970-278-1750

NEVADA CASHMAN EQUIPMENT www.cashmanequipment.com 3300 St. Rose Parkway Henderson, NV 89052 702-649-8777 Fax: 702-633-4699 Elko • 775-738-9871 Reno/Sparks • 775-358-5111

NEW MEXICO WAGNER EQUIPMENT CO. www.wagnerequipment.com Flora Vista 505-334-5522 (Rental) La Cruces 575-647-9700 Albuquerque 505-938-2000 (Rental) 505-345-8411 Hobbs 575-393-2148 (Rental) 575-393-3665 Clovis 505-235-3294 (Rental) Farmington 505-327-5331

NORTH DAKOTA TRACTOR AND EQUIPMENT www.tractorandequipment.com Williston • 701-572-8377

OKLAHOMA OCT EQUIPMENT www.octequipment.com Clinton • 580-323-3422 Oklahoma City • 405-789-6812 Tulsa • 918-437-5085

OREGON WESTERN STATES EQUIPMENT COMPANY www.westernstatescat.com Pendleton • 541-276-5812

“This will transform transportation in Southern California and Las Vegas for generations by providing a fast and efficient connection that gets people out of their cars, reduces traffic congestion, and decreases air pollution,” said Fiona Ma, California state treasurer.

It expects to first complete a link between Las Vegas and Victorville, Calif., with plans to eventually extend the line another 80 mi. (130 km) to Los

Angeles. The project stalled several times over the past decade, mostly due to financing. 

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 13

ALASKA NC MACHINERY www.ncmachinery.com 800-478-7000 Anchorage, AK • 907-786-7500 Dutch Harbor, AK • 07-581-1367 Fairbanks, AK • 907-452-7251 Juneau, AK • 907-789-0181 Prudhoe Bay, AK • 907-659-6900 Wasilla, AK • 907-352-3400

MONTANA TRACTOR AND EQUIPMENT www.tractorandequipment.com Billings, MT • 406-656-0202 Billings-Sgt. • 406-245-4426 Bozeman • 406-585-5800 Great Falls • 406-761-7900 Helena • 406-442-2990 WESTERN STATES EQUIPMENT COMPANY www.westernstatescat.com Kalispell • 406-752-3030 Missoula • 406-721-4050

TEXAS ANDERSON MACHINERY CO. www.andersonmachinery texas.com Corpus Christi • 361-289-6043 Manor • 512-272-8133 Pharr • 956-781-5995 San Antonio • 210-661-2366 Victoria • 361-575-8111 GEORGE P. BANE, INC. www.banemachinery.com Tyler • 903-597-6641 WAGNER EQUIPMENT CO. www.wagnerequipment.com El Paso 915-493-5005 (Rental) 915-821-7651

WASHINGTON NC MACHINERY www.ncmachinery.com 800-562-4735 Seattle • 425-251-5800 Chehalis • 360-748-8845 Fife • 253-896-0878 Monroe • 360-805-6000 Mt. Vernon • 360-424-4292 Wenatchee • 509-886-5561 Yakima • 509-248-2371 WESTERN STATES EQUIPMENT COMPANY www.westernstatescat.com Pasco • 509-547-9541 Spokane • 509-535-1744

WYOMING TRACTOR AND EQUIPMENT www.tractorandequipment.com Worland • 307-347-4747

Page 14 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Toys For Boys (and also men) Realistic Scale Models of Construction Equipment, ideal gifts for the Holidays, Birthdays, Graduation, etc.

Vogele Super 1900-3 Tracked Paver, Caterpillar D7E Track-type Tractor w/ 1:50 scale - $125 Pipe line configuration, 1:50 scale - $115

Caterpillar AP-1050 Asphalt Paver, 1:50 scale - $100

Terex 33-07 Quarry Truck, 1:40 scale - $125

Caterpillar 14M Motor Grader, 1:50 scale - $100

Case 850 Dozer, 1:35 scale - $50

Caterpillar 245 Excavator, 1:50 scale - $100

John Deere 850C Dozer, 1:50 scale - $50

Allis Chalmers Forty-Five Grader, 1:50 scale - $75

Caterpillar 963K Track Loader w/Ripper, 1:50 scale - $85

John Deere 400D Articulated Dump Truck, 1:50 scale - $40

Caterpillar 323F Excavator w/thumb, 1:50 scale - $80

JCB TLT25D Teletruck High Lift, 1:35 scale - $40

JCB 467 WLS Articulated Wheel Loader, 1:50 scale - $75

Volvo L60H Wheel Loader, 1:50 scale - $75

Liebherr L522 Wheel Loader, 1:50 scale - $45

Shipping and Handling Included

WE PURCHASE COLLECTIONS!!!

Bmckeon Collectibles

Contact – Barry McKeon

470 Maryland Drive Fort Washington, PA 19034

610-506-5961

Visit our Ebay Store – bmckeon collectibles – for a complete list with pictures.

Email – bmckeon9@gmail.com

Pages 15-23

Crushing, Screening & Recycling Section For more information on crushing, screening and recycling equipment, visit CEG's Web site at www.constructionequipmentguide.com.

Sennebogen 718 ‘Force Multiplier’ Crushes Workload Jason R. Porter has been attacking his work days lately by getting away from the desk and linking back up with his crews in the field conducting tree removal operations. Treeworks Inc. a TCIA accredited company based in west Michigan, took delivery of a new Sennebogen 718 in October of 2019. Like many tree care company owners, brothers Jason, Zach and Luke Porter started young, working with their father in the late 80’s and continue to work together until this day. “Dad trained us with sweat equity and will power. We worked brutally hard. And to this day, hardly a moment goes by on the work site that I don’t appreciate all the new types of equipment we have, and that have been introduced to our industry,” Jason said. For Jason, the last several years has taken him out of the field from the craft he enjoys and more into an administrative role, managing the company of 14 precise hydraulic system gives him staff. It is a familiar the “feel” and control to operate with path in the industry. surgical precision. “I desperately “You have to be a tree guy,” he wanted to get back cautions. “Aerial experience [buckinto the woods with et truck and climbing], combined the crews and parwith equipment operator experiticipate in producence are invaluable when you are tive tree work, and The Sennebogen 718 contin- working with a Sennebogen 718. If not just be the old ues to crush the workload you have these two skillsets in your tree guy in every- at Treeworks in Michigan. holster, you can knock it out of the one’s way. The park with this machine.” Sennebogen 718 is absolutely a massive force multiplier when I am on a project with Good Fit for it. I really enjoy working with it. After so Right of Way Clearing many years of doing tree work the hard way, Treeworks Inc. is a full-service tree comthis machine feels like vacation.” pany with a focus on commercial contracts for municipalities, county road commis“You Have to Be a Tree Guy” sions, DOT work and utility companies. With the Sennebogen 718, Porter disman“We run four crews, and the Sennebogen tles trees, stacks the wood, and feeds the is a crew unto itself,” said Porter. “A large chipper from the comfort of an air-cushion percentage of our workload is an ideal fit for seat in a climate-controlled cab. this machine. The Sennebogen is not for In his hands are the controls of a hydraulic every tree; you have to know where to grapple saw fitted to the end of 43 ft. (13 m) deploy it. That said, when it is employed telescoping boom. He can elevate the cab for where it is supposed to be, there’s just notha better view of the cutting zone and swing ing else that compares to it.” the boom through 360 degrees to place and Porter first discovered Sennebogen in the stack the removed limbs. A powerful and summer of 2018 after speaking to Ken

A giant silver maple with a crown that arched over the road was dismantled in 50 minutes.

Palmer, a champion tree climber and safety instructor. Palmer invited Porter to a demo day at Sennebogen's head office in Stanley, N.C., where he’d seen the machine going through the paces with operator Rob Frost. “Rob is a tree guy. We have very similar work history. We speak the same language. I knew Rob was presenting the 718 capabilities based on a wealth of actual experience. A spec sheet or salesman can’t do that,” Porter said. “Absolutely Worth It” At the demo, the features to really get Porter’s attention was the maneuverability of the saw head, combined with the telescoping reach and amazing lift capacity. “I immediately saw the value of the machine and began to lament to myself about all the jobs we had suffered through that the Sennebogen 718 could have solved. I knew immediately the machine was a fit for our business going forward.” And now with over 500 hours of operating time in the 718, Porter likes the economics as well. “I can say confidently that the Sennebogen production on our jobs has consistently been equal to two bucket truck crews. For us, that

would be equivalent to two bucket trucks, two track loaders, and four guys. Add up the operating costs of those four pieces of equipment and crew members, it’s a ton. The Sennebogen 718 is absolutely worth it. “It is just stunning how much material you can efficiently move onsite. And it is often less impact to the site and less stress on other machines like track loaders. Many trees barely touch the ground, but go directly into the whole tree chipper. And if you are stockpiling trees and it comes time to chip, you elevate the cab and look down on the pile and into the chipper instead of directly into a big stack of brush. It is a great additional feature that I have grown to appreciate”. Ease, Comfort Porter returns to the ease and capability the 718 brings to his trade. “Think of poor weather conditions, working along a road, in waterfilled ditches full of cattails, mud, and slopes. We used to do that type of work by hand cutting, driving loaders in those areas, over stumps, and pulling material out with a tagline or whatever we could think of just to complete the task. Some of the work can be pretty rough. The Sennebogen takes a task that can be awful and turn it into an enjoyable, successful project. “In March we completed 2 miles of road clearing that would have taken twice the time, and twice the manpower with our old methods. With the 718 we had it done in record time, and nobody broke a sweat,” Porter said. “On another municipal job removing 50 dangerous trees along city streets, the Sennebogen was able to complete 48 of them. And one of the trees was a massive 60+ inch, multi-stem Silver Maple. The crown of this tree arched over the road, utilities and a house. It was late in the day and I closed the street and sent most everyone home so I could focus on just this one technical tree removal. This tree would typically be most of the day for 3 guys and a bucket truck. I had it safely and neatly staged on the ground in about 50 minutes.” “And the thing is, it was fun.” For more information, visit www.sennebogen-na.com. 

Page 16 • July 19, 2020 • www.constructionequipmentguide.com • Recycling Section • Construction Equipment Guide

MB Crusher Helps Cozy, But Cramped Croatian Town Lay New Water Pipes Brodarica in Croatia is a small and peaceful holiday village by the sea. Its catchword is relax. This small cozy area offers amenities where tourists and local families can have a pleasant time. All easily achieved, until recently, when the water mains change became imperative. The quiet in this coastal village could be jeopardized by the major work that needed to be done in the city roads as the road surface needed to be removed in depth to lay the new water pipes. To complicate the matter in this area, the villas and the private houses are separated by paths 6.5 ft. wide; there is barely room to move. So the machines to use needed to be compact and precise. A daunting task for the contractor, they needed to identify the way to go along the roads, dig 7.2 ft. deep and lay the new water pipes without inconveniencing the residents. To do a major work in a residential area is a complex operation. Worsened, in this case, by the lack of space. Not to mention the need to operate in respect of the residents’ security. Tapping the road surface with a hammer proved to be unfeasible because of the vibrations that it caused due to the presence of other pipes and the excessive time frame. To save the day and overcome this challenge an MB Crusher drum cutter MB-R500 attachment was called in. Control, low vibration and compact size are just a few of the advantages this unit has, according to the manufacturer. Mounted on a Takeuchi TB-290-2, the drum cutter managed with ease to grind through the hard limestone typical of the Dalmatian region. How They Did It A compact excavator that can move through the small pathways between houses and private gardens, the MB Crusher drum cutter MB-R500 can grind the limestone with precision and speed, despite the presence of existing pipes. The preparation phase for replacing the underground water mains in this town is undergoing, residents continue to live in the building during the pipeline renovation and the job is keeping the time scheduled. It is always matter of choosing the right equipment for the job, to get the job done right. The MB Crusher cutterhead MB-R500 is the smallest of the line, it weighs only 661 lbs. and its powerful grinder has a diameter of 19.6 in., plus it has several accessories that can be chosen based on the task ahead. If working in enclosed spaces, or on busy roads this rotary

Mounted on a Takeuchi TB-290-2, the drum cutter managed with ease to grind through the hard limestone typical of the Dalmatian region.

The villas and the private houses are separated by paths 6.5-ft. wide; there is barely room to move. So the machines to use needed to be compact and precise.

cutter can be equipped with a drum cover kit to reduce dust emission and stones jolting away. When milling is required to a specific depth, the cutting depth adjustment kit is the right accessory to use. For more information, visit www.mbcrusher.com. 

Construction Equipment Guide • Recycling Section • www.constructionequipmentguide.com • July 19, 2020 • Page 17

Page 18 • July 19, 2020 • www.constructionequipmentguide.com • Recycling Section • Construction Equipment Guide

CRUSHING

MATERIAL HANDLING

SCREENING

TRACKS

Modern Machinery 4428 East Trent Ave. Spokane, WA 99212 800-541-0754

22431 83rd Ave. S. Kent, WA 98032 800-669-2425

19444 Ivan Street SW Rochester, WA 98579 800-304-4421

4610 Cloudburst Way Eugene, OR 97402 800-826-9811

5241 NE 82nd Ave. Portland, OR 97220 800-950-7779

101 International Dr. Missoula, MT 59808 800-332-1617

3155 Highway 93 S. Kalispell, MT 59901 800-434-4190

7850 S. Frontage Rd. Billings, MT 59101 800-735-2589

1257 West Amity Boise, ID 83705 800-221-5211

2735C Tucker Ct. 2666 Garrett Way Jerome, ID 83338 Pocatello, ID 83201 800-221-5211 800-829-4450 www.modernmachinery.com

WASHING & CLASSIFYING

Power Motive Corp. Denver Headquarters 5000 Vasquez Blvd., Denver, CO 80216 303-355-5900 2239 Commercial Blvd. 2340 I-70 Frontage Rd. 2600 Center Dr. Colorado Springs, CO 80906 Grand Junction, CO 81505 Milliken, CO 80543 719-576-5541 970-241-1550 970-587-1188 39 Kay Cee Ln. 7854 Hutchins Dr. Durango, CO 81301 Cheyenne, WY 82007 970-259-0455 307-634-5149 www.powermotivecorp.com

The complete source for equipment in the aggregate, construction and recycling industries. Offering industry-leading brands such as the Pioneer Jaw Crusher, Kodiak® Plus Cone Crusher, SuperStacker® Extendable Stacker, ProSizer® Mobile Screening Plant, Combo® Screen, Vari-Vibe® High-Frequency Screen, Duo-Vibe® High-Frequency Screen, Series 9000 equipment, Fast Trax, Global Track and FastPack.

www.kpijci.com

Construction Equipment Guide • Recycling Section • www.constructionequipmentguide.com • July 19, 2020 • Page 19

6750 Millbrook Rd. • Remus, MI 49340 • 1-800-952-0178 FIND US ONLINE WWW.BANDITCHIPPERS.COM .

Bandit Buuilds More Thaan Machines. Machines .. Bandit Industries has based b its reputaation on a simplee truth – build them strong and stand behind our customers. And thaat’s what we’ve done evvery stepp of the wayy. Every Bandit ndit® machine uses the highhest quality steel and is construucted by specialized teams to sttand up to the toughest jobs. Tha T at’s why more professionals trust a Bandit for their toughest jobs. And every machine is backked by unbeatable factory suppport and an extensive dealer network. twork. When it comes to yourr business, Bandit Industries dooesn’t just build machines. See how Bandit can build your bottom line. Contact your local authorized Bandit dealer today or visit www.banditchippers.ccom to learn more!

SMALL EQUIPMENT DEALERS (Brush Chippers, Stump Grinders, Skid Steer Attachments)

North Valley 15634 N. 32nd Street Phoenix, AZ 85032 602-553-4839

Central Phoenix

A To Z Equipment Rentals & Sales

East Valley 1313 E. Baseline Road Gilbert, AZ 85233 480-558-0067

West Valley

4050 E. Indian School Road 803 E. Van Buren Street Phoenix, AZ 85018 Avondale, AZ 85323 www.a-zequipment.com 602-954-3299 623-435-3078

Page 20 • July 19, 2020 • www.constructionequipmentguide.com • Recycling Section • Construction Equipment Guide

Cat MH3040 Material Handler Cuts Fuel By Up to 25 Percent Delivering the power and reliability required for the most demanding material handling applications in scrap and millyard operations, the new Cat MH3040 builds on the successful legacy of the M325D L MH model. The boom, sticks and other high-stress areas feature thick, multiplate fabrications, castings and forgings to withstand wear and deliver years of durable operation. Specially designed mountings on the upper frame support the new heavy-duty cab. The material handler’s new 202-hp (151kW) Cat C7.1 engine meets stringent U.S. EPA Tier IV Final emission standards with an aftertreatment system that requires no maintenance or downtime. New Smart Mode operation automatically matches engine and hydraulic power to working conditions to reduce fuel consumption, while Power Mode constantly provides maximum power to optimize productivity. The fuel-efficient engine can run up to B20 biodiesel and offers up to 25 percent lower fuel consumption than the M325D L MH, according to the manufacturer. Offering a 12 percent faster swing speed, the MH3040 reduces cycle times and allows operators to move more material in the same amount of time. The advanced hydraulic system features valve priority to direct pressure and flow to where it’s needed and delivers the optimum balance of power, efficiency and load control. The handler’s new heavy lift mode boosts lifting capacities and improves controllability. Its auto warm-up features reduce the time it takes for hydraulic oil warming in cold temperatures to prolong component life. Comfort and Flexibility The MH3040’s larger premium cab design includes sound suppression to reduce operating noise levels inside the cab. Smaller cab pillars combined with large tempered windows deliver enhanced allaround visibility. Rearview and right-side cameras are standard, keeping operator aware of their surroundings. New joystick machine control removes the center steering wheel column to further improve forward visibility. A tip-up left console allows operators to enter and exit the cab much easier. A larger, 10-in. high-resolution touchscreen monitor with jog-dial offers easy navigation of the intuitive operator controls. Joystick controls are ergonomically located within easy reach to reduce operator

The MH3040’s larger premium cab design includes sound suppression to reduce operating noise levels inside the cab. Smaller cab pillars combined with large tempered windows deliver enhanced allaround visibility.

fatigue, while joystick settings and preferred power mode are quickly set to a specific user ID via the monitor. The premium air suspension seat with headrest, heater and ventilator is designed to comfortably adjust to operators of all sizes. Offering a maximum 50.8-ft. (15.5-m) reach, multiple configurations are available for the flexible MH3040 material handler to meet customer needs. Customers can choose from a range of work tool attachments in different sizes to meet the site’s material han-

dling and production needs. Work in low-light conditions with the standard, 1,800 lumen, LED lights on the boom, stick, and cab. The optional 20 kW generator with wiring to stick nose helps to efficiently power magnet attachments for handling fine ferrous material. Simplified Serviceability MH3040 material handler service design changes reduce maintenance costs by up to 20 percent. All fuel filters feature a synchro-

nized 1,000-operating-hour change interval, and the new air intake filter with precleaner lasts up to 1,000 hours to reduce maintenance requirements. Its new hydraulic oil filter improves filtration and increases change intervals to 3,000 operating hours, a 50 percent longer service life over the M325D L MH. New anti-drain valves keep the hydraulic oil clean during filter replacement to improve system longevity. Filter life and maintenance intervals are quickly tracked through the in-cab high-resolution monitor. Featuring electric drive to operate only when necessary, the high-efficiency cooling fans can be programmed to automatically reverse at set intervals to keep the cores clean without work interruptions. The new right-hand-side service access provides easy access for refueling and engine oil checks. Standard Cat Product Link, new to the MH3040 material handler, captures critical operating data such as location, hours, fuel usage, productivity, idle time, maintenance alerts and fault codes, which can be remotely accessed and tracked to boost fleet management efficiency. New Remote Flash works around the production schedule to conveniently assure the machine is operating with the most current version of on-board software, so it delivers high performance, maximum efficiency and minimum downtime. For more information, visit www.cat.com. 

Offering a maximum 50.8-ft. (15.5-m) reach, multiple configurations are available for the flexible MH3040 material handler to meet customer needs. Customers can choose from a range of work tool attachments in different sizes to meet the site’s material handling and production needs.

Construction Equipment Guide • Recycling Section • www.constructionequipmentguide.com • July 19, 2020 • Page 21

Tough Machine es. Dependable Peop ple. Superior Support. We Keep You You Working. Workking.

VISIT THESE SCREEN MACHINE DEALERS Excel Machinery LTD LTD www.excelmach.com Oklahoma, T Texas exas 12100 I-40 East Amarillo, TX 800-858-4002 2719 Hwy 281 N. Mineral Wells, TX 940-325-5298 1230 Industrial Dr. New Braunfels, TX 830-620-1709 8236 W I-40 Service Rd Ste A Oklahoma City, OK 405-440-2333

Power Equipment

www.power-equip.com Colorado, New Mexico, W Wyoming yoming 500 E. 62nd A Ave ve Denverr,, CO 303-288-6801 2940 E. Las V Vegas egas St. Colorado Springs, CO 719-392-1155 2329 River Road Grand Junction, CO 970-243-0722 2836 1st Ave. v Greeley, CO 970-353-1224 100 Barr Avve. SE Albuquerque, NM 505-344-9466

AMERICAN-MADE INNOV NNOV VA ATION SINCE 1966

CRUSH EVERY JOB OBB

™

800-837-3344

740-927-3464

email@screenmachine.com

www.screenmachine.com

17429 US-550 Aztec, NM 970-216-9967 3251 MJB Road Casper, WY 307-577-9700

Page 22 • July 19, 2020 • www.constructionequipmentguide.com • Recycling Section • Construction Equipment Guide

Construction Equipment Guide • Recycling Section • www.constructionequipmentguide.com • July 19, 2020 • Page 23

Page 24 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 25

Larger control valve and electronic controls deliver smooth, precise performance and up to 12% faster cycle times

Bane Machinery 2449 Manana Drive Dallas, TX 75220 800-594-BANE (2263) 10505 North Freeway Fort Worth, TX 76177 800-601-BANE (2263)

Shift-long comfort from a spacious cab, automotive-grade seat and ergonomically-designed, fullyadjustable arm rests

3402 E. NE Loop 323 Tyler, TX 75708 800-594-2200 www.banemachinery.com

Cisco Equipment 1706 S. 1st Street Artesia, NM 88210 800-748-1846 2707 Slaton Hwy. Lubbock, TX 79404 877-745-9595 520 SE Loop 338 Odessa, TX 800-657-3673 620 N. Bell Street San Angelo, TX 76903 800-496-0271 www.cisco-equipment.com

Award-winning Wide Angle Visual Enhancement System (WAVES) provides seamless 270° panoramic view

Ground-level access to routine service points cuts daily maintenance down to just minutes

Oklahoma Territory Construction Equipment 3839 West Reno Ave. Oklahoma City, OK 73107 405-917-9191 866-339-6827 2520 E King Street Tulsa, OK 74110 918-835-7200 866-334-6827 www.oklahomaterritoryequipment.com

Triad Machinery 1601 E. Bay Street Tacoma, WA 98421 253-722-5600 910 N. Thierman Road Spokane Valley, WA 99202 509-534-1900 1210 Dale Lane Mt. Vernon, WA 98274 360-488-3948 4440 SW Airport Road Prineville, OR 97754 888-662-2940 91251 Coburg Industrial Way Coburg, OR 97408 541-342-7700

Tier 4 Final engines deliver up to 12% improved fuel economy…and no DPF to maintain

Robust undercarriage with innovative side-frame design is easier to clean

Nueces Power Equipment 7667 N Sam Houston Parkway Humble, TX 77396 713-247-0066 www.nuecespower.com

18200 NE Riverside Parkway Portland, OR 97230 800-221-8512 www.triadmachinery.com

Page 26 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

How Vermeer’s Andringa Became Her Company’s First Woman in AEM HOF One mile across, seven facilities, her implementation came as much and the need to grow their Pella, Iowa, from the bottom up as it did the top plant physically to meet demand in a down. new market is where Mary Andringa “Being on, and learning from, the found the company founded by her manufacturing floor helps you underfather, Gary Vermeer. That’s when she stand all sorts of processes better,” was challenged by a board member to Andringa would relay to those in her think about the problem sustainably, charge. and not just build another building, as the company started entering the directional boring market, now a major business unit for Vermeer Corporation. It was that challenge that inspired Andringa to dive into Kaizen-style lean manufacturing and implement the principles at Vermeer. The word “kaizen” comes from the Sino-Japanese dictionary meaning “improvement,“ and has been used to describe organizational systems that try to get everyone in a company, from the Mary Andringa CEO to the line workers, in alignment and focused on continuous “Learning” is what drove Andringa improvement. throughout her career that started, literAndringa’s implementation of ally, in the classroom. Before joining Kaizen lean manufacturing principles the family company, Andringa taught allowed Vermeer to, as an example, music to elementary school students. shorten the time it took to go from raw One thing a person inevitably learns steel to a brush chipper from 52 days while teaching elementary age childown to just two. Just as importantly, dren is the importance of health in life

outcomes. That’s why, during the early 2000s recession when Andringa noticed employees having a hard time affording primary medical care, she tapped the healthcare expertise of her husband Dale to create what has become the Vermeer Health Center. Vermeer Health Center provides both primary care and pharmacy services to employees and their family, resulting in both improved well-being of Vermeer employees and an improved bottom line. These accomplishments, and her willingness to think innovatively and successfully implement new ideas is what led to Andringa’s nomination to, and ultimate recognition by, the AEM Hall of Fame. The AEM Hall of Fame has announced its desire to break new ground again in 2020, expanding the traditional idea of a Hall of Fame member and looking to recognize contributions to the industry from more diverse corners of the equipment manufacturing world, including those from different roles and positions, as well as from smaller manufacturers. For more information, visit www.aem.org. 

OSHA Issues Silica Standards Guidance The U.S. Department of Labor’s Occupational Safety and Health Administration (OSHA) recently issued a compliance directive designed to ensure uniformity in inspection and enforcement procedures when addressing respirable crystalline silica exposures in general industry, maritime, and construction. The new directive provides OSHA compliance safety and health officers with guidance on how to enforce the silica standards’ requirements, including: • Methods of compliance; • Table 1 tasks and specified exposure control methods; • Exposure assessments; • Housekeeping; • Respiratory protection; • Regulated areas; • Recordkeeping; • Employee information and training; • Medical surveillance; and • Communication of hazards. The directive also provides clarity on major topics, such as alternative exposure control methods when a construction

employer does not fully and properly implement Table 1, variability in sampling, multi-employer situations and temporary workers. OSHA began enforcing most provisions of the construction standard in September 2017, with enforcement of the requirements for sample analysis starting in June 2018. Enforcement of most of the general industry and maritime standards began in June 2018, with enforcement of some medical surveillance requirements commencing on June 23, 2020. On June 23, 2021, OSHA will begin enforcing requirements for engineering controls for hydraulic fracturing operations in the oil and gas industry. Under the Occupational Safety and Health Act of 1970, employers are responsible for providing safe and healthful workplaces for their employees. OSHA’s role is to help ensure these conditions for America’s working men and women by setting and enforcing standards and providing training, education and assistance. For more information, visit www.osha.gov. 

KOBELCO-USA.COM

Westrax Machinery 19618 S. Susana Rd. Rancho Dominguez, CA 90221 800-411-4717 611 N. Golden Key St. Gilbert, AZ 85233 602-397-8173 www.westraxmachinery.net

Orion Equipment 18060 Des Moines Memorial Drive Seattle, WA 98148 800-280-8124 www.orion-equip.com

TRI-WEST TRACTOR 6281 Southfront Rd. Livermore, CA 94551 925-455-8200 www.tri-westtractor.com

APCO Equipment 3432 N 5th Street North Las Vegas, NV 89032 702-871-7474 www.apcoequipment.com

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 27

Scott Equipment 14635 Valley Blvd. Fontana, CA 92335 909-822-2200 • 800-316-0327 www.scottequip.com

BANE MACHINERY, INC. 2449 Manna Rd. Dallas, TX 75220 214-352-2468

Tyler, TX 903-597-6641 www.banemachinery.com

Fort Worth, TX 817-847-5894

Beard Equipment Co., Inc. 4509 I-20 Frontage Midland, TX 79706 432-694-4530 www.beardequipco.com

Page 28 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Crews Break Up I-25 Job Into Three Construction Phases GAP from page 1

Brannan Sand & Gravel, the subcontractor installing the pavement, is making solid progress. “They can place upwards of 1,500 tons of asphalt with a single paving crew – this equates to a lift of asphalt in a 12foot lane that is 6,000 feet long,” said Blasi. “With asphalt that is 10-inches thick and a top mat of SMA that is 2-inches thick, it takes multiple passes to complete the paving of a single lane.”

a federal infrastructure for Rebuilding America grant. The project also includes the construction four new wildlife crossings and the installation of 30 mi. of deer fencing; adding a new overlay to the existing pavement to create a smoother ride; reconstructing five bridges and extending ramps; a new truck climbing lane approaching Monument Hill from the Greenland Road exit; widening shoulders; and modernizing communications lines along the corridor to enable advanced technology. Construction Sections Crews are engaged throughout the work zone, which has been divided into three construction sections. “This allows construction to begin on one area while design was finalized on another, which let the entire project to begin much earlier than anticipated,” said Paul Neiman, CDOT’s resident engineer. “From the initial study to groundbreaking, this will be the fastest delivery of a project of this size in CDOT history.” The Sky View Lane section (north) – Castle Rock to Sky View Lane (Tomah Road) – was split into three major phases. It covers work in the existing median, such as grading, paving and installation of permanent center barriers, followed by shifting traffic to the newly constructed center of the roadway so paving could occur on the outside sections, and concludes with a traffic shift back to the outside to complete final paving and striping. Southbound I-25 has been shifted to its final alignment, and the final shift along northbound I-25 began in early July 2020. The Greenland Road to Sky View Lane section (middle) is the most complex due to the curvature of the road, and it includes bridge replacements at Upper Lake Gulch Road, Spruce Mountain Road and over Plum Creek, along with one new wildlife crossing. The Greenland Road South section (south) – Greenland Road to Monument – includes raising I-25 to accommodate the wildlife undercrossing north of Greenland Road; the replacement of the single-lane box culvert at Greenland Road with a two-lane underpass; flattening of the vertical curves approaching Greenland Road; replacement of the County Line Road bridge; and addition of a southbound truck climbing approaching Monument Hill. CDOT and Kraemer teams are working together to overcome obstacles in the state’s longest construction zone. “Managing safe ingress and egress through the corridor means moving barrier almost every night as work progresses,” said Michael P. Blasi, KNA’s deputy project manager. “It’s a balancing act of trading access area for work area behind barrier. Effectively managing resources to keep each segment of the project moving but ensuring the critical ones are progressing quickly is a team effort. We utilize a very detailed short interval schedule in concert with a baseline schedule in Primavera P6 to manage this. “Communicating to 200 people and letting them know where we are working, what we are working on, what testing is needed, and the overall plan is not easy,” he added, “and then re-communicating everything when the plan changes. We use our schedule, as well as a daily activities email, to manage this effectively.” Kirk Bergstrom, Ames Construction’s project manager is proud of the progress. “The work is going well, and we will continue to improve coordination with the other players on the I-25 South Gap Team to improve all aspects of the project – safety, quality,

A fair amount of concrete is being placed and several pumping machines have been brought in for the pours.

and scheduling,” he said. “There are several challenges on a project of this magnitude. Although the scope of work is not overly complicated, there is a lot of it. The biggest challenge on the project has been weather. With the amount of moisture we have received, over 100 inches of snowfall this year, it has been, by far, the biggest impact to the project.” Cat trackhoes and blades are playing a vital role for Ames Construction. “For our piping scope of work, we would really be lost without the hoes,” he said, “and for the dirt work/grading, we would really suffer without the blades.” The Colorado terrain where the new lanes are being constructed is not uniform, which makes excavation operations unique. “Every location within this corridor is different,” said Blasi. “Earth work is progressing in a very calculated manner, and it's common for more than 2,000 cubic yards to be moved in a shift with an earthwork crew. We like to get long stretches of embankment and subgrade ready for base course, but only do the base course when they are ready to be paved to minimize exposure of finished base course prior to paving.”

A large Cat excavator lifts dirt for a section of new highway. K-rail separates motorists from the work zone.

Materials Excavation and demolition should generate the 214,923 cu. yds. of earth and rock, 9,081 cu. yds. of concrete, and 879,421 sy. of asphalt. New materials will include 1,246,760 cu. yds. of earthwork, 28,327 cu. yds. of reinforced concrete, and 694,832 tons of asphalt. “The majority of excavated and demo material is reused on-site,” said Blasi. “Asphalt millings are stockpiled for future use by CDOT maintenance or incorporated into the embankment. Concrete is broken down and reused for subgrade stabilization. Steel is scrapped and sent to a recycler. This is a key part of construction and always factored into our projects.” Kraemer has three cranes on-site, as well as some earthmoving equipment and a fleet of forklifts. “They are all regularly maintained by our mechanics,” said Blasi. “Each contractor has its own unique set of maintenance needs.” “We really didn’t encounter any major equipment problems beyond the normal wear and tear that we normally would expect with a fleet this large,” said Bergstrom. “We continue to update our fleet with newer machines because the maintenance cost and lost productions from using older machines can be extensive. We have two mechanics on-site full-time to self-perform repairs and scheduled maintenance. “It is imperative to be proactive rather than reactive,” he added. “Reactive costs money for the unplanned downtime, in addition to the repairs, and tends to be quite a bit more expensive than the maintenance would have been.” A good majority of Ames Construction’s equipment is purchased directly from Caterpillar through Wagner Caterpillar in Denver. “They support us with temporary equipment rentals when needed but also help us work on finding the different pieces as they are needed on the project,” said Bergstrom. “When bad things happen [on projects], we expect them to be handled professionally by both sides. We are in this industry for the long haul and intend to build long-term relationships with our vendors. Knowing and understanding expectations of our dealers and of the equipment will create good working relations with companies but also individuals within these companies.” Highway Information Daily traffic along the entire 18-mi. I-25 South Gap can exceed more than 80,000 vehicles. The project was designed by Jacobs Engineering Group. This is the state’s longest construction zone, and to ensure the safety of the crews and the traveling public, CDOT reduced the maximum speed limit to 60 mph. During the day, CDOT is maintaining two lanes of traffic in each direction. “This is the first-ever project in Colorado to have an onsite Traffic Operations Center to monitor current roadway conditions and possibly reduce congestion by suggesting alternate routes to drivers when incidents occur.” said Neiman.  CEG

SECTION

Attachment & Parts Pages 29-33

For more information about these attachments and more, visit our Attachments Section on our Web site at www.constructionequipmentguide.com

Blackhawk Mulcher Head Knifes Through Vegetation

Designed specifically as a knife tool mulcher, every aspect of the Blackhawk, including rotor diameter and size, ratio of knives to rotor, cutting chamber, even the hydraulic lines, contribute to maximize its production capacity.

This optimized rotor can aggressively shred standing vegetation as well as process materials already on the ground.

Feconâ€™s Blackhawk knife-tool mulching head quickly and efficiently shreds standing vegetation and processes material on the ground. Designed specifically as a knife tool mulcher, every aspect of the Blackhawk, including rotor diameter and size, ratio of knives to rotor, cutting chamber, even the hydraulic lines, contribute to maximize its production capacity. Ideal for skid steer and compact tracked loaders with hydraulic flows of 27 to 45gpm, this new mulcher features 30 knife tools and has a 76 in. cutting width. It is an excellent tool for clearing brush and vegetation, shredding material in woodland urban interface zones, clearing rights-of-way, lot clearing and clean-up, site preparation, and more, according to the manufacturer. This optimized rotor can aggressively shred standing vegetation as well as process materials already on the ground. The ability to process already felled materials creates a more aesthetically appealing end-product and eliminates partially processed material being left behind. Because the Blackhawk efficiently channels material through its cutting cycle, there is minimal draw on the engine, resulting in significantly improved fuel efficiency. Should a rotor stall occur, the unit will immediately recover when extricated from

mulcher. Elimination of 90-degree bends reduces heat buildup in the hydraulic fluid, which allows longer run times and longer service of hydraulic components. Each Blackhawk mulcher can be fine-tuned to the specific hydraulic output of its carrier. Adjusting hydraulic displacement of the motor to match hydraulic flow supplied

the stall-causing material and be ready to reengage. Most of the finely chipped material is broadcast forward of the rotor to minimize the re-processing of already shredded material, further enhancing its efficiency and effectiveness, according to the manufacturer. Hydraulic lines have been completely redesigned for better flow through the

boosts the rotor performance and efficiency. Bolt-in wear parts enhance the economy of the Blackhawk. Rugged construction includes 5/16 in. thick HS steel cutting chamber with AR steel replaceable wear parts. For more information, call 513/696-4430 or visit www.Fecon.com. ď‚§

Hydraulic lines have been completely redesigned for better flow through the mulcher. Elimination of 90-degree bends reduces heat buildup in the hydraulic fluid, which allows longer run times and longer service of hydraulic components.

Page 30 • July 19, 2020 • www.constructionequipmentguide.com • Attachments & Parts Section • Construction Equipment Guide

Can Your

Mini-Excavator... Quick Change from Excavator...

Do This? To Rigid Boom, Universal Skid-Steer Tool Carrier!

It Can Now! XBoom Coupler® System

(800) 526-8538 Amulet.com

Available for most late-model brands up to 13K-Lbs

Firm Installs Mill-Duty Coil Grab Under Overhead Crane A 37.5-ton capacity mill-duty coil grab has been installed beneath the hook of a 40-ton capacity overhead crane at a Monarch Steel Company Inc. facility in Decatur, Ala. The coil grab was manufactured by The Caldwell Group, a Rockford, Illinois-based company that specializes in both standard and custom lifting equipment. Mazzella Alabama Sling Center, a Caldwell Group distributor, provided the coil grab to the Monarch steel service center, located in Decatur in northern Alabama. The grab replaced a previous coil grab that had become damaged over time; the facility opened in 2004. It is rigged below a 92-ft. span top-running double-girder crane, with a single hoist, manufactured by Zenar. The grab carries coils from the processing machine to a floor storage area, over a distance between 100 and 200 ft. Josh Berryman, lifting specialist at Mazzella Alabama Sling, said, “The crane has a standard hook block, but there is a scale system between the block and hook. The hook-scale assembly is used to monitor the weight of the coils being lifted. The crane and grab are operated by a single operator in a standing position, using radio remote control.” He explained that the coils are typically the same size but do vary in dimensions and weigh up to a maximum of 75,000 lb. (37.5 ton). The

“Mill-duty,” as displayed on the coil grab, refers to the high level of work cycles that the equipment is designed for, explained Josh Berryman, lifting specialist at Mazzella Alabama Sling.

maximum outer diameter is 80 in., while the largest inner diameter is 20 in. Coil widths range from 25.5 to 76 in. The crane is Service Class 3 and Crane Manufacturers Association of America (CMAA) Class D, meaning it is rated for heavy service application. The grab is ASME BTH-1 Design Category B, designated when the conditions of the lift are not always defined or predictable, or when load conditions could be severe. Monarch’s customer base includes appliance manufacturers and the auto industry. The tier 1 and tier 2 suppliers to the auto assembly plants rely on these steel service centers, which act as a bridge between metal producers and end consumers. Monarch is headquartered in Cleveland and is one of the country’s largest providers of hot rolled, cold rolled and galvanized steel product. In addition to the site in Decatur, a third service center is located in Cadiz, Ky. For more information, visit www.caldwellinc.com. 

Construction Equipment Guide • Attachments & Parts Section • www.constructionequipmentguide.com • July 19, 2020 • Page 31

ESCO® Attachments

XDP Bucket

H DP Bucke et

ES SCO AND KIRB KIRBY Y-SM - MITH MA ACHINER CHINERY, INC. INC An Unbeatable e Combination on of Performance m and Service ESCO excavator buckets are trussted for productivity and re eliability. Precision enginee ered, our buckets feature the ESCO Ultralok® tooth syystem with its integrated h hammerless lock that offerss safer and easier tooth replacement. placement. These featuress combined with premium m materials and skilled fab b brication; deliver one o of the most durable, highh Ultralok® perform mance buckets available.

Tooth o System

Contact Kirby-Smith Machinery ry, Inc. I for expert guidance and service to meet your ur excavating needs. s. Abilene 877-577-5729 Amarillo 8 00-283-124 47 Dallas 8 00-753-1247 Ft. Worth o 877-851-9 97 77 www.esco.weir

Hewitt (Waco) a 254-261-1370 Lubbock 8 6 6-28 9-6 0 87 McAlester 918-310-1550

Odessa 877-794-18 00 Oklahoma City 8 00-375-333 5 9 Tulsa 8 00-375-3733

Page 32 • July 19, 2020 • www.constructionequipmentguide.com • Attachments & Parts Section • Construction Equipment Guide

Unique Transformation...

ALLU Turns Construction Waste Into Valuable Materials The ALLU series of attachments are being used to literally transform construction waste from demolition projects into valuable materials, according to the manufacturer. The unique attributes of the Allu Transformers, along with the recently launched Allu Crusher, have enabled asphalt, concrete, soil, bricks and other materials, to be turned into products for reuse. Allu Transformer screener crushers offer solution for separating, sorting, screening and loading for several different types of demolition materials. The base Transformer comprises of an excavator/ loader/tractor mounted processing bucket which screens, pulverizes, blends, mixes, separates, even crushes, feeds and loads materials. The result is that the material is effectively transformed into highly valuable products, making any business involved in demolitionand so forth more efficient, and more profitable. What makes the Transformers an ideal solution for processing demolition materials is that as they are fitted to compact and versatile loaders, meaning that they are able to access even the most hard to get to sites. This enables on site processing, with the materi-

als, such as concrete and bricks, often being reused directly where they are most needed. This results in cost savings when there is less material for the landfill as well as more material for reuse. In addition to cost savings, the environmental benefits are impressive, as the weight of the end product is reduced by upwards of 50 percent, meaning that transport is reduced, and with it any harmful emissions, according to the manufacturer. Latest Development Ideal for Recycling One of the latest developments, which has proven to be ideal for dealing with and recycling demolition materials, is the Allu TS blade structure. This has been developed to improve productivity with at its core being the configuration of the screening blades that spin between the screening combs. The TS drums are available with two different blade types: standard blades for screening applications and axe blades when a crushing or shredding effect is required. Blade sizes available include 16-32 mm, 2550 mm and 35 mm, with the assembly enabling three different fragment sizes from

the same unit. Fragment size estimation is based on screening comb distance, with it being quick and easy to change from one screening job to another, providing more versatile processing. Due to the TS’s self-cleaning design high capacity operation is ensured, even when the materialis wet or contaminated, due to the system’s non-clogging structure, according to the manufacturer. New ALLU Crusher The very latest development from ALLU aimed at the demolition and recycling market is its new crusher series of — initially — three crusher models for excavators in the 10 to 33 ton range. All have purpose developed features that ease their use and optimize performance, whilst providing easy maintenance in the field. Amongst the many customer focused features included on the new Allu crushers are: • Reversible crushing: This reduces the potential for jamming, blockages, or obstruction with rebar are avoided, while delivering greater levels of production and reducing the need for any manual involvement in the crushing process.

• Feed plate design built into the jaw: Ensures that the feeding function in a fully loaded chamber delivers high rates of production with minimal risk of bridging. • Simple mechanical pin adjustment for output size regulation: Makes the entire crushing process easy and safe with quick adjustment for various output specifications. • The crusher ‘opens like a clam’: Through this design easy and quick replacement ofwear parts is ensured through ease of access, saving time spent on maintenance, thereby minimizing risk to operators and maximizing productive crushing. Jeroen Hinnen, vice president of sales of Allu Group said, “By bringing this new product line to market we will be able to provide customers with what they have been looking for. The Allu Transformer range offers unique productivity and efficiency benefits on a great deal of demolition materials and recycling applications, while the Allu Crusher range enables hard rock, and heavy duty — such as reinforced concrete — demolition materials, to be effectively reduced.” For more information, visit www.allu.net. 

Construction Equipment Guide â€˘ Attachments & Parts Section â€˘ www.constructionequipmentguide.com â€˘ July 19, 2020 â€˘ Page 33

Waukesha-Pearce Industries, Inc.

BIRTH OF A LEGEND CONTACT YOUR LOCAL AREA SALES REPRESENTATIVE TO FIND OUT WHY THE LABOUNTY MSD LEGEND SHEARS ARE THE MOST PRODUCTIVE SHEARS LABOUNTY HAS EVER MADE

www.wpi.com 12320 South Main Street Houston, TX 77035 713-551-0506 Austin 512-251-0013 Beaumont 409-721-5305 Buffalo 903-322-7150 Corpus Christi 361-884-8275 Edinburg 956-386-0107 Kilgore 903-984-2011 San Antonio 210-648-4444 Tomball 281-351-9016

Modern Machinery

DUAL MAXTM INDEXABLE PROTECTION

10% MORE FORCE

INSITETM EQUIPPED

The industryâ€™s only full-protection, indexable, piercing tip

The new MSD 2500 Legend has enhanced jaw geometry resulting in 10% more cutting force at the apex compared to prior model.

InSiteTM pulls information from LaBounty shears to provide performance metrics that help increase productivity and reduce downtime.

/D%RXQW\Ě?|Ě? +Z\ Ě?|Ě?7ZR +DUERUV 01 Ě?|Ě? |Ě?ZZZ VWDQOH\LQIUDVWUXFWXUH FRP EUDQGV ODERXQW\

www.modernmachinery.com 4610 Cloudburst Way Eugene, OR 97402 800-826-9811 541-688-7321 Portland, OR 971-222-1710 Rochester, WA 360-273-4284 Kent, WA 253-872-3500 Spokane, WA 509-535-1654 Kalispell, MT 406-755-5540 Missoula, MT 406-523-1100 Billings, MT 406-252-2158 Boise, ID 208-336-8570 Jerome, ID 208-324-4522 Pocatello, ID 208-233-5345

Page 34 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Five Ways You Can Engage Policymakers in Response to COVID-19 Pandemic By Wade Balkonis Special to CEG

As our member companies respond to the COVID-19 pandemic, they’ve told us their priority is to ensure their workers' safety and health while also obtaining access to the resources available to them to keep production going. After all, equipment manufacturers and our 2.8 million men and women are an essential part of our nation’s frontline response to COVID-19. Knowing how much our industry is doing, and will need to continue to do to help rebuild our economy, it’s also important that we all tell our elected officials what is needed to keep our industry safe while maintaining a high level of production. There’s no better time to do that than right now as Congress and President Trump are demonstrating a willingness to work on a bipartisan effort to pass legislation to help working families and American businesses. For example, the relatively quick passage of the $2 trillion Coronavirus Aid, Relief, and Economic Security (CARES) Act, the largest U.S. economic rescue package in history, and a new agreement to replenish funds for the Paycheck Protection Program (PPP), means legislators are ready and willing to act. As we respond to the COVID-19 crisis and our industry works to help rebuild our economy, our policymakers need to hear from AEM, its members companies, and the I Make America community. With that in mind, and especially as our nation largely continues to practice social distancing, here are five ways you can engage with your elected officials: 1. Sign a petition. Petitions can make a big impact by showing a community’s support for policy initiatives and communicate that support to decision makers in one collective voice. Technology allows you to sign petition digitally and join a movement from anywhere. https://www.imakeamerica.com/campaign/take-a-stand-for-u-s-manufacturing/ is focused on revitalizing America’s manufacturing sector on behalf of the 2.8 million men and women who support it. Behind each signature is a voice and joining together we can make the most noise.

2. Email and phone are tried and true. Emails and phone calls have always been a tried and true way to communicate a message directly to a lawmakers’ office. You can either check your elected leader’s website for their phone or email contact or you can visit AEM’s

10-year-old national grassroots campaign, I Make America, online. The I Make America website makes it especially easy for our members to engage with their appropriate elected leaders by automatically connecting supporters with their appropriate Senators or Representatives through ongoing issue campaigns. Supporters’ messages always help lawmakers and their staff learn more about their constituents’ priorities and take those into account for policymaking. Phone calls also can be directed to lawmakers’ Washington, D.C., or local, in-district offices. 3. Web and video calls Due to the crisis, and the need to social distance, many lawmakers still want to hear directly from their constituents but aren’t able to in person — for their safety and for yours. That’s why several Congressional offices have turned to online conference platforms, including Zoom, Skype, Blue Jeans, Google Hangout, or other methods. As a constituent, if you’re comfortable with using these types of platforms, then don’t be afraid to ask for meeting using any of these options.

4. Social media These days, social media also is a powerful communication tool for constituents. Looking up your Member of Congress’s confirmed handle on Twitter or their official Facebook profile page, and sharing with them a short story or update on how your company is responding to the crisis gives them another way to better understand how they can help. Many elected leaders are highly active on social media, tweeting or posting several times a day. You also can empower your employees to share their stories directly with their elected leaders since social media is so widely adopted and encourages simple, concise messages as well sharing photos and videos. 5. Write in to your local newspaper. Your congressional, state, and local elected leaders always pay attention to what their newspapers back home are covering. That includes the opinion and editorial section of their local and state newspapers. It’s another one of the best ways they can learn about what’s on the minds of their constituents and it catches their eye because they realize other voters in their district or states may be influenced by what you have to say. Here are a few tips on how to write a letter to the editor or op-ed to your local paper: • Personalize your message: Share a story of how an issue is impacting you, your work, your family or community. • Focus on a single point: Try to focus on specific issue, instead of a range of issues. By emphasizing issue, it makes it easier for your elected representative to focus on one thing and makes it easier for them to help. • Be specific with what you want: Always try to end with a specific call to action. You want your elected official to declare your work “essential” during the COVID-19 crisis, or you want your elected official to make easier for your company to apply to a small business loan. Whatever your ideal outcome, make sure you make it clear, especially in your conclusion. As a constituent, you have a right to have your voice heard, and we encourage you to continue to engage in advocacy on behalf of your company, your employees, and our industry. Wade Balkonis is the AEM Grassroots Advocacy Manager 

OKLAHOMA TERRITORY CONSTRUCTION EQUIPMENT www.oklahomaterritoryequipment.com Oklahoma City, OK 405-917-9191 Tulsa, OK 918-835-7200

Garton Tractor Inc. www.gartontractor.com 2400 N Golden State Blvd. • Turlock, CA 95382 209-632-3931 Fairfield, CA • 707-425-9545 Merced, CA • 209-726-4600 Modesto, CA 95356 • 209-538-0911 Newman, CA • 209-862-3760 Santa Rosa, CA • 707-586-1790 Stockton, CA 95206 • 209-948-5401 Tulare, CA 93274 • 559-686-0054 Ukiah, CA 95482 • 707-468-5880

CLM EQUIPMENT CO. INC. www.clmequipment.com Lafayette, LA 337-837-6693 Lake Charles, LA 337-625-5942 Houston, TX 281-598-2500

BANE MACHINERY INC. www.banemachinery.com Dallas, TX 800-594-2263 Ft. Worth, TX 800-601-2263 Tyler, TX 800-594-2200

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 35

Cooper Equipment Co. www.cooperequip.com 201 Commerce Blvd. Georgetown, TX 78626 512-930-5151

TRI-WEST TRACTOR, INC. www.tri-westtractor.com

Westrax Machinery www.westraxmachinery.net

19618 S. Susana Rd. 6281 Southfront Road Rancho Dominguez, CA 90221 Livermore, CA 94551 Dealer Im mprint Area800-411-4717 925-455-8200

Shafer Equipment Company, Inc. www.shaferequipmentco.com 955 Greg Street • Sparks, NV 89431 775-235-4069

19885 Temescal Canyon Rd Corona, CA 92881 800-411-4717

APCO EQUIPMENT www.apcoequipment.com

BEARD EQUIPMENT CO.

3432 N 5th Street North Las Vegas, NV 89032 800-574-4089

4509 I-20 • Midland, TX 79706 432-694-4530

www.beardequipco.com

611 N. Golden Key St. Gilbert, AZ 85233 602-397-8173

Rasmussen Equipment Co. www.raseq.com 3333 West 2100 South West Valley City, UT 84119 801-972-5588

Page 36 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Bill Gives Spending Boosts to Infrastructure BILL from page 1

“In the Moving Forward Act, we do that by modernizing the crumbling roads and bridges we already have; investing more than $100 billion in transit to put more zero-emission buses on the road, add new routes, and provide more reliable service; tripling Amtrak’s funding; funding the essential dredging and upkeep of American harbors, ports and channels to keep cargo moving; and investing in new wastewater infrastructure to encourage efficiency and affordability, and help communities address stormwater needs, preventing pollution in local rivers,” he continued. House leaders understand that one of the best ways to promote new economic growth is by investing in the nation’s aging, and often over-burdened, infrastructure, said Stephen E. Sandherr, CEO of the Associated General Contractors of America (AGC). “These investments will create needed new construction careers, promote demand for new construction equipment and materials and ensure that the economy will be more efficient and effective for years to come. The new House infrastructure proposal will provide the kind of tangible benefits our economy needs to recover.” The package takes several positive steps to ensure that its investments support high-quality jobs, said Karla Walter, senior director of employment policy at the Center for American Progress in Washington D.C. “COVID-19 has sparked a national recession that has left Americans from all walks of life reeling,” she said. “Federal policymakers can help get millions of Americans back to work by supporting economic recovery through investment in critically needed public infrastructure,” she added. “Yet in order to maximize the benefits of this spending, policymakers must be intentional about ensuring that this investment creates good jobs that are available to all working Americans.” Rejuvenation Through Construction One-third of the $1.5 trillion funding package represents a five-year surface transportation reauthorization, dubbed INVEST in America. Dean Franks, senior vice president of congressional relations of the American Road & Transportation Builders Association (ARTBA), said the highway and transit portion would be paid for in part with a transfer of $145 billion to the Highway

Trust Fund (HTF). “The transfer would cover the shortfall between anticipated HTF user fee receipts and proposed spending in the measure,” Franks said in ARTBA’s Washington Newsline. The House legislation would rebuild U.S. communities with infrastructure and innovation that is smarter, safer and made to last, touted the House Committee on Transportation and Infrastructure. In addition to rejuvenating roads and bridges, the bill would invest in public transit and the national rail network, building out fueling infrastructure for low- and zero-emission vehicles and deploying technology and innovative materials. “The INVEST in America Act is fueled by American workers and ingenuity thanks to strong Buy America provisions and labor protections,” stated the committee. The bill also invests in schools through the Reopen and Rebuild America’s Schools Act, a $130 billion package targeting the infrastructure of high-poverty educational facilities that endanger the health and safety of students and educators. “This investment will help students get back to school and create more than two million jobs to help workers get back to work,” according to the committee’s statement. It upgrades child-care facilities by leveraging a five-year, $10 billion federal investment in sure that child-care settings are safe, appropriate and able to comply with current and future health directives. The end goal would be to generate additional state and private investments. The funding package invests more than $100 billion into affordable housing infrastructure to create or preserve 1.8 million homes. “These investments will help reduce housing inequality, create jobs and stimulate the broader economy, increase community and household resiliency in the face of natural disasters, improve hazardous living conditions, and increase the environmental sustainability of our housing stock,” according to the House transportation committee. The bill invests more than $25 billion in the Drinking Water State Revolving Fund and other programs to ensure communities have clean drinking water. It also helps remove dangerous contaminants, such as PFAS, from local water systems. The fund modernizes energy infra-

structure, investing more than $70 billion to transform the electric grid to expand and accommodate more renewable energy, strengthen existing infrastructure, help develop an electric vehicle charging network and support energy efficiency, weatherization and Smart Communities infrastructure. It would deliver affordable highspeed broadband Internet access to all parts of the country through the investment of $100 billion to promote competition for broadband internet infrastructure in unserved and underserved communities. Priority would be given to communities with persistent poverty. The legislation would get children connected to remote learning, closes broadband adoption and digital skills gaps and enhances payment support for low-income households and the recently unemployed. It would invest $30 billion to upgrade hospitals to increase capacity and strengthen care, help community health centers respond to COVID-19 and future public health emergencies, improve clinical laboratory infrastructure, support the Indian Health Service’s infrastructure, and increase capacity for community-based care. It would invest $25 billion in the U.S. Postal Service to modernize infrastructure and operations, including a zero emissions postal vehicle fleet, processing equipment and other goods. It would also incentivize the development of wind and solar on public lands and build a workforce for offshore wind. Finally, the funding package would promote investments in communities by spurring private investment through the tax code, through a revitalized Build America Bonds program, expansions of Private Activity Bonds, and significant enhancements to the New Markets Tax Credit and the Rehabilitation Tax Credit, according to the committee’s statement. Construction Benefits “Major investment in infrastructure would help to restart the economy by directly sustaining and creating millions of jobs for American workers,” said Walter of the Center for American Progress. “These workers would jumpstart growth in other sectors by spending their new earnings in their communities, even during this time of social distancing — for example, at local stores and restaurants.” She believes this would then signal private companies to begin hiring and investing in capital projects.  CEG

www.roadmachinery.com Phoenix, AZ 480-545-2400 Phoenix, AZ 602-252-7121 Prescott, AZ 928-778-5621 Tucson, AZ 520-623-8681 Bakersfield, CA 661-695-4830 Hayward, CA 510-659-1903 Fresno, CA 559-834-3149 Mojave, CA 661-824-2319 Perris, CA 909-355-3600 Pico Rivera, CA 562-699-6767 Redding, CA 530-229-3820 Sacramento, CA 916-375-3540 Santa Rosa, CA 707-544-4147

ROAD MACHINERY LLC

www.powermotivecorp.com DENVER HEADQUARTERS 5000 Vasquez Blvd. Denver, CO 80216 303-355-5900 Colorado Springs, CO 719-576-5541 Durango, CO 970-259-0455 Grand Junction, CO 970-241-1550 Milliken, CO 970-587-1188

POWER MOTIVE CORPORATION

Cheyenne, WY 307-634-5149

www.komatsueq.com 1486 South Distribution Drive Salt Lake City, UT 84104 801-972-3660

KOMATSU EQUIPMENT COMPANY 4460 Pioneer Way Elko, NV 89801 775-753-7557

1409 East 3850 South St. George, UT 84790 435-986-1000

3825 Losee Road North Las Vegas, NV 89030 702-399-1004 900 Marietta Way Sparks, NV 89431 775-356-1334

10790 South Highway 59 Gillette, WY 82718 307-682-1445 405 Jonah Drive Rock Springs, WY 82901 307-686-1300

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 37

WAUKESHA-PEARCE INDUSTRIES, INC.

www.wpi.com 12320 S. Main Street • Houston, TX 77035 713-723-1050 Buffalo, TX • 903-322-7150 Corpus Christi, TX • 361-884-8275 Edinburg, TX • 956-386-0107 Kilgore, TX • 903-984-2011 Pflugerville, TX • 512-251-0013 Port Arthur, TX • 409-721-5305 San Antonio, TX • 210-648-4444 Tomball, TX • 281-351-9016

KIRBY-SMITH MACHINERY INC.

www.kirby-smith.com 6715 W Reno Avenue • Oklahoma City, OK 73137 405-495-7820 McAlester, OK • 918-310-1550 Tulsa, OK • 918-438-1700 Abilene, TX • 325-692-6334 Amarillo, TX • 806-373-2826 Dallas, TX • 214-371-7777 Ft. Worth, TX • 817-378-0600 Lubbock, TX • 806-745-2112 Odessa, TX • 432-333-7000 Waco, TX • 254-261-1370

AUTOMA MAT TED TO MAKE THE PRODUCTION N YOU NEED

www.komatsusw.com 6101 Pan American W Freeway NE Albuquerque, NM 87109 505-345-8383

KOMATSU SOUTHWEST 4520 National Park Hwy • Carlsbad, NM 88220 575-628-8301 901 Troy King Road • Farmington, NM 87401 505-324-8601 1181 Burgundy Drive • El Paso, TX 79907 915-872-1001

www.clairemontequipment.com 7651 Ronson Road • San Diego, CA 92111 858-278-8351

CLAIREMONT EQUIPMENT 1330 W Mission Road • Escondido, CA 92029 760-739-9100 8520 Cherry Avenue • Fontana, CA 92335 909-429-9100 440 West Aten Road • Imperial, CA 92251 760-355-7700 81-501 Industrial Place • Indio, CA 92201 760-863-5558

4726 Convoy Street • San Diego, CA 92111 858-278-8338

Want to make your next n machine acquisition really count? nt? Komatsu’s lineup of automated excavators, including thee all-new PC360LCi-11 and PC4490LCi-11 feature a revolutionary, faactory integrated, machine control system. The exclusive intelligent ligent Machine Control tecchnology lets operators focus on moving oving materials efficiently, without worrying about digging tooo deep or damaging the target surface. Contact your Komatsu distributor tributor to learn how you cann hit pay dirt today with Komatsu innnovation.

020

Page 38 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

BUILDING A BETTER WORK FORCE ONE CANDIDATE AT A TIME

Marc Murphy, VP of Construction

WHEN YOU NEED QUALITY, BUT CAN’T AFFORD TO WAIT Our placement success in the construction disciplines spans the entry-level, middle and senior management and executive levels in the following areas: Project Managers and Superintendents Project Sales Engineers Controls and Project Engineers Estimators Service and Project Sales Construction Managers

CFOs, CEOs, CDOs General Managers Service Managers Sales Managers Sales Training Managers

CONSTRUCTION

Corporate Headquarters 1275 Drummers Lane, Suite 103 • Wayne, PA 19087

Call Today: 610-941-0100 • Email: info@magellangroup.com

www.magellangroup.com

Trucks & Trailers

SECTION

Pages 39-40

To view our current comparison trailer specification charts visit www.constructionequipmentguide.com

Mack, ATA Team Up With ALAN to Deliver Vital Aid, Goods To assist those impacted by the coronavirus pandemic, Mack Trucks and the American Trucking Associations (ATA) are partnering with the American Logistics Aid Network (ALAN) to deliver vital supplies, such as food and personal-care items, to nonprofit organizations who distribute these goods locally. “In good times and bad, the trucking industry moves nearly three-quarters of our nation’s freight, helping ensure crucial supplies are delivered where they are needed,” said Martin Weissburg, president, Mack Trucks. “Working in partnership with ATA and ALAN enables us to more effectively marshal resources and deliver supplies to organizations addressing the needs of local communities across the country.” Two model year 2019 Mack Anthem models, which Mack provided to the ATA as part of its sponsorship of the Share the Road and Workforce Heroes programs, are now delivering shipments of supplies between nonprofit organizations, including Feed the Children and Joshua’s Heart Foundation, among others. Professional truck drivers from ATA member companies have volunteered their time to make the deliveries.

Since the ATA’s Share the Road wrought by Hurricane Katrina in and Workforce Heroes live safety 2005,” said Elisabeth Barna, and career education efforts have executive vice president, industry been postponed or cancelled due affairs, ATA. “At that time, our to shelter-in-place requirements Share the Road Mack Pinnacle and other safety precautions, axle back model made its maiden Mack and ATA released both voyage to New Orleans with a Anthem models to make delivertruckload of water.” ies coordinated through ALAN. ALAN was contacted in April “Given all of the supply chain by Feed the Children, a leading chaos surrounding COVID-19, it hunger relief organization fightwould have been easy for these ing to end childhood hunger by organizations to press the pause distributing food and other essenbutton on their charitable program tials for daily living through its until the crisis was past,” said network of community partners Kathy Fulton, ALAN’s executive across the country. As the director. “But we’re so thankful response to the coronavirus panthey didn’t, because trucking is demic began impacting traditionalways one of our non-profit part- The Mack Anthem Workforce Heroes model is helping deliv- al distribution efforts, Feed the ners’ biggest needs. And these er vital supplies. Children began looking for soluvehicles are allowing us to support tions to ensure its tens of thouthem with transportation resources during a sands of pounds of food and beverages, permany relief efforts in a really big way.” The partnership between the ATA and crisis. In addition to connecting non-profits sonal care items and laundry detergent locatALAN traces back several years and in need with transportation solutions, ALAN ed in its LaVergne, Tenn., warehouse made through several natural disasters. ALAN, helps humanitarian organizations make its way swiftly to non-profit partners around which was founded in 2005, provides sup- every logistics dollar count. the country. It was critical to them to make “ATA’s relationship with ALAN dates to sure the ever-growing needs of those affectply-chain assistance to disaster relief organizations and other non-profits by connecting their creation, following the devastation ed by the pandemic could be met. One of those community partners is the Miami, Fla.-based Joshua’s Heart Foundation. Founded in 2005 by a then 4year-old Joshua Williams, the organization is dedicated to the fight against global hunger and poverty. “Our mission is to empower needy people to improve their quality of life by providing them necessities like groceries and personal items,” said Williams, Joshua’s Heart Foundation founder and chief changemaker. “Like all organizations, the pandemic has affected our ability to receive and distribute goods, making the shipments from Feed the Children through ALAN critical to our efforts.” Mack and ATA will continue to coordinate transport solutions with ALAN until demand subsides. For more information about ALAN, visit https://www.alanaid.org/. To learn more about Feed the Children and the Joshua’s To assist those impacted by the coronavirus pandemic, Mack Trucks and the American Trucking Associations (ATA) are part- Heart Foundation, visit https://feedthechilnering with the American Logistics Aid Network (ALAN) to deliver vital supplies, such as food and personal-care items, to non- dren.org and https://joshuasheart.org. To profit organizations who distribute these goods locally using the ATA Share the Road (pictured) and Workforce Heroes Mack learn more about ATA, visit Anthem models. www.trucking.org. 

Page 40 â€˘ July 19, 2020 â€˘ www.constructionequipmentguide.com â€˘ Trucks & Trailers Section â€˘ Construction Equipment Guide

Fellingâ€™s IT-I Tilt Features Removable Attachment Rack Felling Trailers Inc. introduced its newly designed removable attachment rack for its IT-I (industrial tilt) model line. The removable attachment rack is a bolt on feature, mounted on the IT-Iâ€™s 5 ft. (1.5 m) stationary platform and sits inside the stake pockets on the exterior of the trailer then bolted in place. The rack is an ideal pairing with the IT-I tilt trailer, providing ample room to transport a skid steer on the 18 ft. (5.5 m) tilt deck, along with multiple attachments and various job site tools like shovels and brooms on the rack. The ability to transport all of these job site tools in one trip, safely, and efficiently saves the operator and their crew time and miles. Functionality and flexibility, the attachment rack has a 54 in. (137 cm) deck height allowing ample room to transport larger attachments such as grapple forks, trenchers, stump grinders, etc. on the stationary deck below the rack. The top rack provides a generous amount of space, 5 ft. by 81 in. (205.7 cm), to transport dirt/snow buckets, tillers or rollers. Keeping the load secure, the attachment rack has an angle lip on the front, and each side with rub rail and stake pockets, providing the operator several points of securement. Additional storage for shovels/brooms is located on the roadside of the attachment rack with three bolt-on tubes. Built strong enough to carry the load, the removable

Functionality and flexibility, the attachment rack has a 54-in. (137 cm) deck height allowing ample room to transport larger attachments such as grapple forks, trenchers, stump grinders, etc. on the stationary deck below the rack.

attachment rack offers a capacity of 2,500 lbs. (1,134 kg). Felling Model FT-16 IT-I With Attachment Rack â€˘ 5 ft. stationary platform + 18 ft. tilt deck â€˘ Auto tilt deck latch mechanism â€˘ 2 to 8,000 lb. axles with torsion suspension â€˘ 215/75R17.5 tires on plate wheels â€˘ Blackwood rubber infused decking

,?7,90,5*, @6< *(5 ;9<:; 8<(30;@ ;/(; 0: 796=,5 <RX NQRZ ZKDW \RX QHHG WR KDXO )HOOLQJ KDV WKH WUDLOHU WR JHW LW WKHUH :LWK RYHU \HDUV FRPELQHG LQGXVWU\ VDOHV H[SHULHQFH ZH KDYH WKH DQVZHUV WR \RXU VSHFLDOL]HG WUDLOHU QHHGV )7 /3 ZLWK $LU 5DPSV

)7 7$ $LU 7LOW ZLWK $LU 5DPSV

)7 /3 ZLWK $LU %L )ROG 5DPSV

(09 9(47: $ 56 /,(=@ 30-;05. $ 56 )(*2 051<9@ :JHU 5V^ [V >H[JO =PKLV

=PZP[ ^^^ MLSSPUN JVT *,. ,THPS [YHPSLYZ'MLSSPUN JVT *HSS

â€˘ Pallet fork holder â€˘ Toolbox with lockable cover in hitch â€˘ Dual cushion cylinder tilt with lock valve â€˘ Twin 12k drop leg jacks â€˘ Removable attachment rack on stationary platform â€˘ Sublime green paint For more information, call 800/245-2809 or visit www.felling.com. ď‚§

Mack Defense Headquarters Relocates to Customer Center To better serve customers, as well as enhance its capability to support military and government contracts, Mack Defense has relocated its headquarters to the Mack Customer Center (MCC) located in Allentown, Pa. The move, which was recently completed, also provides Mack Defense additional working space and access to other MCC amenities. â€œThe Mack Customer Center is an outstanding facility and presents our company and the Mack brand in a way we could not replicate at our previous location,â€? said David Hartzell, president, Mack Defense. â€œWe have easier access to a number of unique features at the MCC, such as the test track and industrial space, while still retaining the robust security requirements that are required when working on military contracts.â€? Military and government contracts often include classified information, which requires additional security measures. Mack Defense worked with the U.S. Defense Counterintelligence and Security Agency

(DCSA) and the MCC facility team to ensure the required physical and technological security requirement are in place. In addition to meeting security needs, the new space also offers prospective customers a more complete representation of Mack Defense and its capabilities. â€œWhen hosting current and prospective customers, the MCC facility paints a completely different picture than our previous location, demonstrating the wide range of solutions we can offer our customers,â€? said Hartzell. Mack Defenseâ€™s move was timed specifically to utilize the enhanced capabilities available at the MCC to support the current active contract with the U.S. Army to provide heavy dump trucks. Mack Defense was awarded a firm-fixed-price $296 million contract in May 2018 from the U.S. Army to produce up to 683 M917A3 heavy dump trucks (HDT). For more information, visit www.mackdefense.com. ď‚§

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 41

Attention Contractors! Post Your Wanted To Buy Listings FREE! Here’s How! List Your Wanted Items

If you would like to place your Wanted To Buy listings on our website for inclusion in our newsletters, simply visit: www.ConstructionEquipmentGuide.com/wanted and enter your listings. Inappropriate or Sale Ads will be Deleted WANTED (USA): AKERMAN MOTOR GRADERS, ALL MODELS. PLEASE LET US KNOW IF YOU HAVE ANY MACHINE LIKE THIS (WORKING OR NON). EMAIL: HIEEQUIPMENT@GMAIL.COM; PHONE: 775-235-8837 –––––––––––––––––––––––––––––––– WANTED: 3-AXLE, HEAVY DUTY LOW BOY TRAILER FOR HAULING A CAT 963. EMAIL: BENHOOVER@SBCGLOBAL.NET –––––––––––––––––––––––––––––––– WANTED (CT): CASE 1455B CRAWLER LOADER. EMAIL: HENRYINDUSTRIES@YAHOO.COM –––––––––––––––––––––––––––––––– WANTED (IL): NEED MANUALS AND PARTS FOR 1970 BARBER-GREENE TF-30 DRAINAGE TRENCHER (TILING MACHINE). EMAIL: JL.FOMAC@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (US): BATTERY BOX FOR A KOMATSU PC170LC-11. EMAIL: MROBERSON@ LYLEMACHINERY.COM PHONE: 601-624-1124 –––––––––––––––––––––––––––––––– WANTED (FL): MORBARK 4600XL GRINDER. EMAIL: RKCLANDDEVELOPMENT@ATT.NET –––––––––––––––––––––––––––––––– WANTED (FL): TRANSMISSION FOR EARLY '90S VINTAGE P&H CENTURY RT50. EXISTING IS A SHINKO RCM2509B S/N 0005. PARTS OR SUBSTITUTE TRANNY OR ENGINE/TRANS CONSIDERED. EMAIL: MIKE.SMITH@ CERTIFIEDBOOMREPAIR.COM PHONE: 813-247-1963 –––––––––––––––––––––––––––––––– WANTED (CA): BOBCAT T550 COMPACT TRACK LOADER. EMAIL: CINDYLARK4@MSN.COM –––––––––––––––––––––––––––––––– WANTED (PA): REXWORKS INC MAXIGRIND 425 GRINDER. EMAIL: HENRYINDUSTRIES@YAHOO.COM; PHONE: 814-371-8010 –––––––––––––––––––––––––––––––– WANTED (PA): FORD F700 HOOK LIFT TRUCKS - WORM GEAR AND SHAFT ASSEMBLY FOR COMPACT MODEL H-L SIDE-O-MATIC BOOM UNLOADER COMPACT 2 7-63-5C DICO CONTINUOUS SERIES. EMAIL: INFO@LESNEYCONCRETE.COM PHONE: (724) 224-8703 –––––––––––––––––––––––––––––––– WANTED (USA): HYUNDAI ATTACHMENTS - LOOKING FOR A GOOD USED GP BUCKET 4-6 CU.YD. FOR A 1996 HYUNDAI HL770 LOADER. EMAIL: DONNIE@RADIATIONCLEANTECH.COM; PHONE: 601-319-9453 –––––––––––––––––––––––––––––––– WANTED (NY): BANDIT 65 WOOD CHIPPER - USED BRUSH BANDIT 65XP, 75XP, 2002 OR NEWER, 35HP MINIMUM. EMAIL: DSPTECH11@GMAIL.COM ––––––––––––––––––––––––––––––––

WANTED (USA): HITACHI EX400LC-1 EXCAVATOR EMAIL: ILYAS.MTCPK@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED: LOOKING FOR 1000LB FRONT COUNTERWEIGHT FOR CASE 455C CRAWLER LOADER. EMAIL: ROGERPF1@FRONTIERNET.NET; PHONE: 570-639-3058 –––––––––––––––––––––––––––––––– WANTED (US): CAT 311, 312, 315, 320, 325, 330, 336 CL,DL,EL EXCAVATORS UNDER 8000 HOURS. EMAIL: REBUILD@TUSCO.NET; PHONE: 330-987-3508 –––––––––––––––––––––––––––––––– WANTED: AMPHIBIOUS EXCAVATORS, ALL MAKES AND MODELS, NEW OR USED + ALL MAKE AND MODEL BOOMS AND STICKS LONGER THAN NORMAL + ALL MAKE AND MODEL BROKEN BOOMS AND STICKS. EMAIL: PERCY.RES@GMAIL.COM; PHONE: 215-350-1165 –––––––––––––––––––––––––––––––– WANTED (US); LOOKING FOR PILOT VALVE 9137384 FOR HITACHI 200LC-3 EXCAVATOR. EMAIL: PJUREKX1@GMAIL.COM; PHONE: 585-492-2449 –––––––––––––––––––––––––––––––– WANTED (US): CATERPILLAR OFFHIGHWAY TRUCKS - I NEED #5 CAT 775D &E ROCK BEDS ONLY. ONLY NEED BEDS. EMAIL: WEBBPAGE1@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (US): CONCRETE PUMPS WANTED - SCHWING, PUTZMEISTER, ALLIANCE, CIFA, ETC. ALL MODELS, BRANDS, SIZES. OLD OR NEW! BOOM PUMPS,TRAILER & TRUCK MOUNTED CITY PUMPS PURCHASED. OLD RETIRED, NO LONGER USED & PARTS PUMPS ALSO PURCHASED. EMAIL INFORMATION A.S.A.P. INSTANT PAYMENT GUARANTEED !! FINDERS FEES PAID!!! EMAIL: BBENEDETTO@COMCAST.NET –––––––––––––––––––––––––––––––– WANTED (PA): I’M LOOKING FOR A PUSH THERMOPLASTIC MACHINE. CAN BE ANY BRAND. EMAIL: HELLOELISA@ICLOUD.COM –––––––––––––––––––––––––––––––– WANTED (USA): CAT 330-336 DL SERIES EXCAVATORS EMAIL: REBUILD@TUSCO.NET –––––––––––––––––––––––––––––––– WANTED (RI): CATERPILLAR 4+ MISCELLANEOUS EQUIPMENT. I AM HELPING A FRIEND TO FIND A PART FOR HIS CAT MODEL 426, SERIAL #7BC02647, PART #9R383. IT WOULD BE REALLY HELPFUL IF THIS PART WAS AVAILABLE IN EASTERN USA, ESPECIALLY IN THE NORTHEASTERN STATES, AND AVAILABILITY, PRICE, AND SHIPPING ARE IMPORTANT IF THE PART IS AVAILABLE ELSEWHERE. THANK YOU FOR YOUR HELP. EMAIL: JOETTAKIRK@AOL.COM ––––––––––––––––––––––––––––––––

WANTED (WORLDWIDE): CATERPILLAR D8R CRAWLER DOZER. LOOKING FOR ORIGINAL 2018 D8R CATERPILLAR BULLDOZER. EMAIL: ARABHURUR@GMAIL.COM; PHONE: +251-911513133 –––––––––––––––––––––––––––––––– WANTED (SC): ALL MODELS BRADCO TRENCHING / BORING / CABLE PLOWS; LOOKING FOR 3 PT HITCH 3 OR 4 FOOT TRENCHER 6" WIDE FOR REAR KUBOTA EMAIL: PEPPERJACKPM@YAHOO.COM; PHONE: 803-460-2600 –––––––––––––––––––––––––––––––– WANTED (USA): ALL MODELS CATERPILLAR EXCAVATORS. LOOKING FOR USED AMPHIBIOUS EXCAVATORS, MARSH BUGGIES AND MARSH MASTERS - ANY BRAND. ALSO LOOKING FOR BROKEN/DAMAGED LR BOOMS AND STICKS. EMAIL: PERCY.RES@GMAIL.COM; PHONE: 215-350-1165 –––––––––––––––––––––––––––––––– WANTED (US): INGERSOLL RAND AIR COMPRESSOR, MODEL 125 CFM. NEED EXHAUST/INTAKE MANIFOLD FOR A CONTINENTAL G193A GAS ENGINE WHICH IS IN THE I/R GYRO FLOW 125 COMPRESSOR. EMAIL: HFINCHTTD@FONTIERNET.NET –––––––––––––––––––––––––––––––– WANTED (VA): FORD 1920 758B BACKHOE ATTACHMENT. EMAIL: CONWELL1208@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (US): USED HITACHI EXCAVATORS EX200LC,EX270LC,EX400LC. EMAIL: ILYAS.MTCPK@GMAIL.COM; PHONE: +92-332-248-9350 –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): 1-FINAL DRIVE & CONTROL VALVE ASSEMBLY, 2-ENGINE WIRING HARNESSES, HOODS, DISPLAY MODULES & ECU'S SN #FGY0381 FOR SAMSUNG SE240 LC-3 EXCAVATOR. EMAIL: TVHCSHOP@GMAIL.COM; PHONE: 920-735-1221 –––––––––––––––––––––––––––––––– WANTED (KS): CAT 922B INJECTION FUEL LINE. I NEED ALL 4 FOR MY 1960'S DIESEL FRONT-END LOADER. EMAIL: BLACKNIGHT64R@ATT.NET –––––––––––––––––––––––––––––––– WANTED: CAT WHEEL LOADER 950B, 950E, 966E, 966F, 966FII. EMAIL: NAQIB_KHAN73@YAHOO.COM –––––––––––––––––––––––––––––––– WANTED: HITACHI EXCAVATORS EX200, EX270LC, EX400, EX400LC. EMAIL: NAQIB_KHANINTRCO@ HOTMAIL.COM. –––––––––––––––––––––––––––––––– WANTED: LINCOLN WELDERS, MODELS 250/300/225. I'D LIKE TO BUY USED MACHINES LOW HOURS. EMAIL: JONATHANDAYTON4@GMAIL.COM; PHONE: 806-292-7452 –––––––––––––––––––––––––––––––– WANTED (CA): JOHN DEERE 330 EXCAVATOR. EMAIL: JIMWLAMBERT@HOTMAIL.COM ––––––––––––––––––––––––––––––––

WANTED (NM): BARBER GREENE BG-225B SLAT CONVEYOR, COMPLETE LEFT SIDE. EMAIL: JR_STRIPING@LIVE.COM –––––––––––––––––––––––––––––––– WANTED (US): LOOKING FOR CME 45 WITH DEUTZ DIESEL DECK ENGINE AND AUTOMATIC HAMMER. ANY CONDITION. EMAIL: GEONETICS@BELLSOUTH.NET –––––––––––––––––––––––––––––––– WANTED (IL): HAULOTTE AERIAL LIFT, ALL MODELS. LOOKING FOR A TOWABLE BOOM LIFT. EMAIL: SAWMANDAN@SBCGLOBAL.NET PHONE: 630-553-7612 –––––––––––––––––––––––––––––––– WANTED (MI): ALL MODEL KUBOTA WHEEL LOADERS. EMAIL: CRAIGBERENS944@GMAIL.COM PHONE: 616-813-3642 –––––––––––––––––––––––––––––––– WANTED (NV): CATERPILLAR 14G MOTOR GRADER. EMAIL: SALES1@HIEEQUIPMENT.COM PHONE: 7025295171 –––––––––––––––––––––––––––––––– WANTED (USA): LOOKIN FOR A GOOD USED KOMATSU PC 400-5 EXCAVATOR EMAIL: FJS-1@ATT.NET PHONE: 724-944-5569 –––––––––––––––––––––––––––––––– WANTED (USA): TAKEUCHI TB0-35 AND 135 WITH CABS. RUNNING OR FOR PARTS. PHONE: 443-392-5789 –––––––––––––––––––––––––––––––– WANTED (WORLDWIDE): ALL MODELS CATERPILLAR COMPACT TRACK LOADERS, USED CATERPILLAR SKID STEER LOADERS 226D, 232D, 236D, 242D, 246D, 262D, 272D, 272D XE. EMAIL: LSGLOBAL@NVER.COM –––––––––––––––––––––––––––––––– WANTED (USA): A GOOD USED C-12 CAT ENGINE FOR A SHORT NOSE 2000 PETERBILT 379 ROAD TRACTOR. ENGINE TO HAVE CORRECT ECM AND S# BEGINS WITH 2KS , 380 MIN. HP. CONTACT JIM ARNETT JARNETTJR@ORBITSDO.COM; CELL# 937-603-3965. –––––––––––––––––––––––––––––––– WANTED (USA): CATERPILLAR D11 CRAWLER DOZERS - INTERESTED IN PARTS FOR LARGE DOZERS FOR COAL MINES AND AGGREGATE QUARRIES. EMAIL: BIGIRONLUNS87@YAHOO.COM –––––––––––––––––––––––––––––––– WANTED (USA): CAT 315,320,325,330,336 DL SERIES EXCAVATORS UNDER 8000 HOURS AND WHOLESALE PRICED MACHINES. EMAIL: REBUILD@TUSCO.NET PHONE: 330-987-3508 –––––––––––––––––––––––––––––––– WANTED: TAKEUCHI MINI EXCAVATORS TBO-35’S WITH CABS, RUNNING MACHINES AND/OR PARTS. PHONE: 443-392-5789 ––––––––––––––––––––––––––––––––

WANTED (NY): LOOKING FOR USED 5 TON WIRE ROPE HOIST TO RUN ON A PATENT TRACK EMAIL: INFO@ BRIDGEHAMPTONSTEEL.COM PHONE: 631-537-2486 –––––––––––––––––––––––––––––––– WANTED (TX): CATERPILLAR 330C L EXCAVATOR - LOOKING TO BUY CATERPILLAR 330CL & 330DL IN GOOD RUNNING CONDITION. EMAIL: RIZ@MEGAEQUIPMENTS.COM PHONE: 832-528-0786 –––––––––––––––––––––––––––––––– WANTED: ALL MODELS TRENCOR TRENCHING / BORING / CABLE PLOWS. EMAIL:ADMIN@MITCHELLHOPPER.COM PHONE: 432-888-2593 –––––––––––––––––––––––––––––––– WANTED (FL): BOBCAT MT50 COMPACT TRACK LOADERS EMAIL: EIDNKSLJK@ICLOUD.COM PHONE: 6039 2I28 939 –––––––––––––––––––––––––––––––– WANTED: ALL MODELS CATERPILLAR WHEEL LOADERS. LOOKING TO BUY ANY CAT LOADER AT WHOLESALE PRICE. EMAIL: MARKETING@ GCESEQUIPMENT.COM PHONE: 714-408-1587 –––––––––––––––––––––––––––––––– WANTED (TX): ALL MODELS CATERPILLAR MOTOR GRADERS. EMAIL: MAGDIELLERMA@GMAIL.COM PHONE: 956-432-7379 –––––––––––––––––––––––––––––––– WANTED (USA): ALL MODELS CATERPILLAR WHEEL LOADERS. CAT 966H OR K WITH UNDER 10,000 HOURS, BUCKET, COUPLER. SET OF FORKS IS A PLUS. EMAIL: REBUILD@TUSCO.NET PHONE: 330-987-3508 –––––––––––––––––––––––––––––––– WANTED (WV): ALL MODELS TERRAMITE BACKHOE LOADERS - CHECKING PRICES FOR TERRAMITE T7 FRON RIM FOR SERIAL NUMBER 227X0102. EMAIL: EDWINANDDIANA@FRONTIER.COM –––––––––––––––––––––––––––––––– WANTED (FL): CASE CRAWLER DOZERS, ALL MODELS. EMAIL: JABOWEND@GMAIL.COM –––––––––––––––––––––––––––––––– WANTED (USA): KOBELCO K907D EXCAVATORS - MAIN HYDRAULIC CONTROL VALVE (907D) SERIAL #LN7001 TO YG0501. KOBELCO PART # 2436U1165F2, KAWASAKI TAG # KMX15A/23009 ALSO USED ON YUTANI 1986, MODEL 195. EMAIL: PTSCOTT@HTVA.NET –––––––––––––––––––––––––––––––– WANTED (USA): KOMATSU ATTACHMENTS - SKELETON BUCKET FOR KOMATSU 220 EXCAVATOR 54" TO 60". CAN ADAPT FROM OTHER MACHINES AS LONG AS ITS 80 MM PINS. EMAIL: FJS-1@ATT.NET PHONE: 724-944-5569 ––––––––––––––––––––––––––––––––

WANTED (USA): HYDRA-MAC 1700 SKID STEER LOADER. EMAIL: MALONEYFARM.1@ WINDSTREAM.NET –––––––––––––––––––––––––––––––– WANTED (TX): CATERPILLAR EXCAVATORS, ALL MODELS. EMAIL: PAUL@HEAVYSURPLUS.COM; PHONE: 214-625-2652 –––––––––––––––––––––––––––––––– WANTED (US): CATERPILLAR D5B OR D6C CRAWLER DOZER. EMAIL: JT_FERGUSON_EXC@SBCGLOBAL.NET –––––––––––––––––––––––––––––––– WANTED (CA): CATERPILLAR 970F WHEEL LOADER. EMAIL: SALES3@GCESEQUIPMENT.COM; PHONE: 657-347-6605 –––––––––––––––––––––––––––––––– WANTED (GA): KOBELCO EXCAVATORS, ALL MODELS. MINI- OR MIDIEXCAVATOR. USED. UNDER 2000HRS. CA 35 T0 40 HP FULLY FUNCTIONAL. THUMB EMAIL: JKSAPP@BELLSOUTH.NET –––––––––––––––––––––––––––––––– WANTED (US): LIMA CRANE – ANY LIMA 2400B MACHINES IN ANY TYPE OF CONDITION. EMAIL: REBUILD@TUSCO.NET –––––––––––––––––––––––––––––––– WANTED (US): CATERPILLAR D8T CRAWLER DOZER. LOOKING FOR MACHINE WITH ISSUES AND/OR HIGHER HOURS, AT A WHOLESALE PRICE. BUYER WANTS MACHINE CHEAPER THAT HE CAN PUT THROUGH HIS SHOP AND REFURBISH AS NEEDED. EMAIL: REBUILD@TUSCO.NET PHONE: 330-987-3508 –––––––––––––––––––––––––––––––– WANTED (US): YANMAR YFW55R DUMPERS - FINAL DRIVE OR A PARTS MACHINE. EMAIL: ORDERS@LEWEQUIP.COM; PHONE: 724-887-9375 –––––––––––––––––––––––––––––––– WANTED (US): GEHL DL-10H-55 TELEHANDLERS / FORKLIFTS - SN # 10H55JR024028 NEED PART # L71553. EMAIL: JEFF.JAEGER@HOTMAIL.COM; PHONE: 345-925-9709 –––––––––––––––––––––––––––––––– WANTED (US): BOBCAT S175 SKID STEER LOADERS; ANY STATE NEAR ARKANSAS WOULD BE HELPFUL. EMAIL: BRIANFITZJURLS@GMAIL.COM; PHONE: 479-847-4202 –––––––––––––––––––––––––––––––– WANTED: LINK-BELT LS-348H CRANE – LOOKING FOR THE BOOM WIRE WRAP FOR A LINK-BELT 348 HYLAB , S/N L9J89965. EMAIL: POWERALEXHEAVY EQUIPMENT@GMAIL.COM PHONE: 386-496-1340 ––––––––––––––––––––––––––––––––

Page 42 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Auctions are subject to change, please check Auctioneers websites for details ALEX LYON & SON AUCTIONEERS www.lyonauction.com 315-633-2944 • Canastota (Syracuse), NY Fri., July 24, 2020 For: Major Job Completion, Late Model Construction Equipment • Canastota (Syracuse), NY Sat., July 25, 2020 For: Fanciest Late Model Construction Equipment in conjunction with Haycamp & Barbecue! • Barnesville, OH Fri., July 31, 2020 For: Late Model Construction Equipment & more • Attleboro, MA Sat., August 1, 2020 For: Construction Equipment, Trucks, Support & more • New Castle, PA Fri., August 7, 2020 For: 2 Job Completions. Construction Equipment & more RITCHIE BROS. AUCTIONEERS www.rbauction.com 402-421-2631 All our auctions are now online bidding only! • Fort Worth, TX July 28 - 29, 2020 • Denver, CO August 5, 2020 • Tipton, CA August 12, 2020 • Houston, TX August 25 - 26, 2020 • Orlando, FL August 27, 2020 • Phoenix, AZ August 28, 2020 • Kiefer, OK September 2, 2020 • Mountain West Regional Event September 8, 2020

• Sacramento, CA September 23, 2020 • Midwest Regional Event September 29 - 30, 2020 ABSOLUTE AUCTION & REALTY, INC. www.AARauctions.com 800-243-0061 • Hyde Park, NY Sat., July 25, 2020 For: Surplus Vehicle & Equipment BAR NONE AUCTION www.barnoneauction.com 866-372-1700 • Online/Portland, OR Fri., July 31, 2020 For: Monthly Public Auction • Online/Sacramento, CA Sat., August 8, 2020 For: Monthly Public Auction • Online/Portland, OR Fri., August 28, 2020 For: Monthly Public Auction BIDADOO AUCTIONS www.bidadoo.com 1-877-BIDADOO • ONLINE ONLY July 21, 2020 • ONLINE ONLY July 28, 2020 • ONLINE ONLY August 4, 2020 • ONLINE ONLY August 11, 2020 • ONLINE ONLY August 18, 2020 • ONLINE ONLY August 25, 2020 • ONLINE ONLY September 1, 2020 • ONLINE ONLY September 8, 2020 BIG IRON www.bigiron.com 800-937-3558 • ONLINE ONLY July 22, 2020

• Atlanta, GA September 9, 2020

• ONLINE ONLY July 29, 2020

• Northeast Regional Event September 16 - 17, 2020

• ONLINE ONLY August 5, 2020

Coming Auctions To view information on upcoming auctions visit our Auction Calendar at www.constructionequipmentguide.com

• ONLINE ONLY August 12, 2020 • ONLINE ONLY August 19, 2020 • ONLINE ONLY August 26, 2020 HESS AUCTIONEERS www.hessauctioneers.net 866-511-2493 • Marietta, PA Fri., August 14, 2020 For: Trucks, Trailers & Equipment I.R.A.Y. AUCTION www.iraymn.com 320-968-7230 • ONLINE ONLY Wed., July 29, 2020 For: Heavy Equipment, Truck & Trailer Auction J.J. KANE AUCTIONEERS www.jjkane.com 856-764-7163 • TIMED ONLINE ONLY Wed., July 22, 2020 For: Construction, Utility Equipment and more (Plymouth Meeting, PA) • TIMED ONLINE ONLY July 29 - 30, 2020 For: Construction, Utility Equipment and more (Concord, NC) • TIMED ONLINE ONLY Wed., August 12, 2020 For: Construction, Utility Equipment and more (Shrewsbury, MA) JAMES G. MURPHY INC. AUCTIONEERS www.murphyauction.com 425-486-1246 • ONLINE ONLY July 30 – August 6, 2020 For: Kenmore Heavy Equipment, Contractors Equipment & Vehicles

JEFF MARTIN AUCTIONEERS, INC. www.jeffmartinauctioneers.com 601-450-6200 • ONLINE ONLY Tues., July 28, 2020 For: Vistra/Luminant Online Power Plant Auction • ONLINE ONLY July 29 - August 4, 2020 For: East Coast Heavy Equipment & Truck Auction • Brooklyn, MS August 7 - 8, 2020 For: Early Fall Construction & Transportation Public Auction

• ONLINE ONLY Wed., July 22, 2020 For: Vehicles & Equipment Auction

• West Fargo, ND Wed., July 29, 2020 For: AgIron West Fargo Event

• ONLINE ONLY Thurs., July 23, 2020 For: Construction Equipment Auction

• ONLINE ONLY July 30 – Aug. 6, 2020 For: Construction Consignment Auction

• ONLINE ONLY Thurs., July 23, 2020 For: Hunt Utility Surplus Auction

• ONLINE ONLY August 7 - 12, 2020 For: Timed Online Upper Midwest Locations

• ONLINE ONLY Tues., July 28, 2020 For: City of Sioux Falls SD Auction

• ONLINE ONLY August 7 - 17, 2020 For: Kibble Equipment Auction

• ONLINE ONLY Wed., July 29, 2020 For: Ag Equipment Auction

• ONLINE ONLY August 21 - 26, 2020 For: Timed Online Upper Midwest Locations

• ONLINE ONLY Thurs., July 30, 2020 For: Truck & Trailer Auction

• ONLINE ONLY Tues., August 11, 2020 For: Heavy Equipment Auction

• ONLINE ONLY Thurs., July 30, 2020 For: Paragon Contracting LLC Auction

• ONLINE ONLY August 12 - 18, 2020 For: Absolute Auction Kaolin Mining Equipment & Related items

• ONLINE ONLY Tues., August 4, 2020 For: Government Auction

McGREW EQUIPMENT COMPANY www.mcgrewequipment.com 888-311-2811 • ONLINE ONLY Tues., July 21, 2020 For: Farm & Construction Equipment Auction

• ONLINE ONLY Wed., August 5, 2020 For: Vehicles & Equipment Auction ROYAL AUCTION GROUP, INC. www.royalauctiongroup.com 239-936-4121

• Campbell, MN Thurs., August 27, 2020 For: Antique Tractor & Classic Car Auction THE AUCTION COMPANY www.theauctioncompany.net 951-657-5300 • ONLINE ONLY Mon., July 20, 2020 For: Construction Equipment, Trucks & more VANTAGE AUCTIONS www.vantageauctions.com 951-228-9040 • Live Virtual Auction Sat., July 25, 2020 For: July 2020 Auction

• ONLINE ONLY Tues., July 28, 2020 For: Farm & Construction Equipment Auction

• Fort Meyers, FL August 7 - 8, 2020 For: Heavy Equipment, Industrial Machinery, Trucks & Trailers, Commercial Vehicles & more

PAUL E. SAPERSTEIN INC. www.pesco.com 800-660-6553

RTI AUCTIONS www.teitsworth.com 585-243-1563

• Braintree, MA Wed., July 29, 2020 For: Sale @ Public Auction Graziano Brothers

• ONLINE ONLY • Perris, CA August 1 - 4, 2020 Fri., August 7, 2020 For: Empire Farm Days 2020 For: Public Auction

PURPLE WAVE AUCTION www.purplewave.com 866-608-9283 • ONLINE ONLY Tues., July 21, 2020 For: Government Auction

• Live Virtual Auction Sat., September 26, 2020 For: September 2020 Auction WESTERN CONSTRUCTION AUCTIONS INC. www.wca-online.com 866-731-7760

STEFFES GROUP INC. www.steffesgroup.com 701-237-9173

WSM AUCTIONEERS www.wsmauctioneers.com 623-936-3300

• ONLINE ONLY July 17 - 22, 2020 For: Timed Online Upper Midwest Locations

• Phoenix, AZ Sat., August 8, 2020 For: Live & Online Public Auction

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 43

Public Online Auction: KENMORE HEA HEAVY H AVY VY EQUIPMENT EQUIPMENT, PMENT, CONTRACT CONTRACTORS TRACTORS EQUIPMENT T & VEHICLES S - ONLINE ONL ONLY NLY AUCTION N S t a r t D a t e : 11 : 0 0 A M | T h u r s d a y - J u l y 3 0 E n d D a t e : 11 : 0 0 A M | T h u r s d a y - A u g u s t 6 1 8 2 2 6 6 8 t h Av e n u e N E . , K e n m o r e , WA 9 8 0 2 8 4809 HOURS

2007 JOHN DEER RE 544J

4558 HOURS

2007 JO OHN DEERE 544J

1999 GROVE 6640G

4507 HOURS

2007 JOHN DEERE E 544J

2011 JOHN N DEERE 5085M

JAMES AM MES G. MURP MURPHY HY CO. C O . IND INDUSTRIAL D US TRI AL AUCTIONEERS AUCTI U O NEERS S Heavy eavy v Equipment, Contractors Equipment, quipment, Trucks Truc ks & Vehicles Vehicl es Preview: 8am m - 4pm August 4th & 5th For Mor M e Information go to Murphya auction.com 1 OF 3

1993 BOBCAT 753 7

DRESSER

1 OF 4

2009 KENWORTH T8 T 00

2003 IN T’L 5600I

2002 IN T’L 2674

2002 FREIGH TLINER FLD112084SD

1 OF 3

KOBELCO SK54S SRX

FRE EIGH TLINER M2

Bid B id online onll ine i - murphyauction.com mu rph h yaucttion. t ti com - 425.486.1246 425. 425 5 .48 48 8 6.1 6 1 2 46

Page 44 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Business Calendar To view our Business Calendar online, go to www.constructionequipmentguide.com. JULY 2020 CRANE SAFETY COURSES NEW LOCATIONS! REGISTER TODAY! July 20 – July 24, 2020 Overhead Hoist Maintenance Training, Houston, TX July 28 – July 31, 2020 Overhead Crane Train The Trainer, Cincinnati, OH July 28 – July 31, 2020 Overhead Crane Inspector Training, Houston, TX August 3 – August 7, 2020 Overhead Hoist Maintenance Training, Orlando, FL August 4 – August 6, 2020 Forklift Operator Train The Trainer, Houston, TX August 4 – August 7, 2020 Mobile Crane Inspector Training, Cincinnati, OH August 10 – August 14, 2020 Mobile Crane Train The Trainer, Portland, OR August 11 – August 13, 2020 Rigging Inspector Training, Cincinnati, OH August 11 – August 14, 2020 Overhead Crane Inspector Training, Orlando, FL August 20 – August 21, 2020 Qualified Signal Person Training, Orlando, FL To register and for more information, please call or email Tiffany Alston. Telephone: 800/654-5640, extension 238. Direct: 321/710-4641. Email: talston@cranesafe.com

Dates: July 28, 2020 - 2:00pm to 3:00pm Price: Member : $149 Non-Member: $199 Description: The AGC Business Development WebEd Series, brought to the AGC membership by the AGC BD Forum, will be held in May, June and July of this year and will be sure to improve your business by focusing on the basics of Business Development, Marketing and Proposals for the General Contractor. We are confident that by the end of this WebEd Series, you will be more prepared to grow your talent within your company, expand your client map and continuously improve your processes and strategies.. Part One: Basics of Business Development for the Busy General Contractor – May 12, 2020-COMPLETED Part Two: Basics of Marketing for the Busy General Contractor – June 23, 2020-COMPLETED Part Three: Basics of Proposals and Presentations for the Busy General Contractor – July 28, 2020 Most proposals and presentations have 3 things in common; a lot of talk about how great we are; a lot of boiler plate language that says the same thing as our competitors; and Boring, boring, & more boring. All 3 are losing behaviors! In this webinar, we will discuss the following: • Gathering the intel needed to craft a tailored message • Creating a compelling offering around the client’s key issues • Flipping the focus from “Us” to “Them”. • Focusing on the “Benefits” we offer, as opposed to the “Features” • Mastering the use of the Executive Summary • And much more! For more information on the above event, contact AGC of America, 2300 Wilson Blvd. Suite 300, Arlington, VA 22201. Phone: (703) 548-3118. www.agc.org. For computer specifications, please visit https://www.gotomeeting.com/meeting/online-meeting-support or contact webinars@agc.org.

MINNESOTA ASPHALT PAVEMENT ASSOCIATION (MAPA) 7th Annual MAPA Golf Outing When: Monday, August 10, 2020 Time: 10:30 am - 7:00 pm Where: Bunker Hills Golf Club 12800 Bunker Prairie Rd NW Coon Rapids, Minnesota 55448 Save the date! RUETER’S EQUIPMENT ELKHART OPEN HOUSE We are ready FORE summer and a great golf event! Mark your calenWhen: Friday, July 24, 2020 dar for August 10 and get your foursome together as you won’t want Time: 12 NOON - 6:00 pm to miss this year. We’re back at Bunker Hills! Where: Rueter's Elkhart This will be a great networking opportunity for all participants. We are 2425 NE 126th Ave., Elkhart, IA 50073 hoping for another great turnout and beautiful August weather. Save the date! Join us for an afternoon of Machine Demos, Lunch and Excavator Proceeds will go to the MAPA Scholarship Fund and Academic Basketball! Run a variety of machinery including Skid Steers, Institution Donation Fund. Excavators, Wheel Loaders, Telehandlers and more! The ticket cost for this event is $150 (Before June 24) and $190 Demos from brands including JCB and Hyundai! Lunch will be pro- (June 24 and After). Ticket includes lunch, green fee, ½ cart, vided at 12 noon. For more information or questions on the above beer/soda on the course, dinner and prizes. event, call 515-367-3054. Limited to the first 144 players. Visit www.asphaltisbest.com/events to register online or download ASSOCIATED GENERAL CONTRACTORS (AGC) the registration form. If you need to switch out a member of your fourAGC’s Three Part Webinar Series: Business Development, some after registering, please contact MAPA Event Coordinator, Grace Marketing & Proposal Basics for the General Contractor Gothers at graceg@ewald.com.

For more information on the above event, contact MAPA, 1000 been reduced to $475. No a-la-carte registration options are availWestgate Drive, Suite 252, St. Paul, MN 55114. Phone: 651/636- able, with the exception of the Excellence in Construction® Awards 4666. Email: info@mnapa.org. gala* and the National Craft Championships day pass. If you plan to attend the August Convention and have not yet reached out to us, NATIONAL ASSOCIATION OF WOMEN IN CONSTRUCTION (NAWIC) please email meetings@abc.org to confirm your registration. The Dawn of a New Era: NAWIC 65th Annual Conference For more information and to register for this event, please visit VIRTUAL EVENT http://abcconvention.abc.org..or contact Associated Builders and Dates: August 12 – 14, 2020 Contractors, 440 1st St., N.W., Ste., 200, Washington, D.C. 20001. Now that we have made the transition to virtual for NAWIC’s 65th Phone: 202/595-1505 Email: gotquestions@abc.org. Annual Conference (and FIRST ever VIRTUAL conference), we are truly in The Dawn of a New Era! ENGINEERING NEWS-RECORD (ENR) NAWIC Annual Conference aims to create a support network for oth- Groundbreaking Women in Construction VIRTUAL Conference ers like themselves. Women in Construction of Fort Worth was so Dates: August 24 – 27, 2020 successful that it gained its national charter in 1955 and became the NEW DECADE ... NEW DRIVERS ... NEW DECISIONS National Association of Women in Construction. Today, NAWIC pro- ENR’s Groundbreaking Women in Construction (GWIC) conference in vides its members with opportunities for professional development, education, networking, leadership training, public service and more. San Francisco was a success last year with record breaking attenIn addition to keynote speakers, countless seminars and panel dis- dance and enlightened discussion on critical workforce topics. We cussions, our Industry Council Networking this year provides an welcome you be a part of our first ever virtual conference this August opportunity for you to meet and interact with fellow NAWIC members 2020! and colleagues in the construction industry during lunch breaks and GWIC is much more than just a conference. It is recognized as one at designated times through each day of the Virtual Conference. You of the industry’s premier leadership and talent management events— a catalyst for change to inspire women at all levels to develop their definitely won't want to miss out on these! The registration fee for this conference is $350 for members and leadership skills, expand their influence and boost industry growth potential. Our varied programming and virtual event platform will $400 for non-members. allow you and your peers to share, learn, challenge and inspire each Your registration fee this year includes: other to contribute to your workplace and employer and realize career • Free Conference T-shirt and Pin! • Registration packet that includes goodies from sponsors and part- success! Register today! ners! (To be mailed after conference) For more information on the GWIC Virtual Conference, visit • Access to all conference materials and recordings for TWO DAYS https://www.enr.com/groundbreaking-women-in-construction. after the end of conference – in case you can’t catch everything in “real time”! Register today! HISTORICAL CONSTRUCTION EQUIPMENT ASSOCIATION (HCEA) For more conference details and to purchase tickets for the NAWIC 35th Annual International Convention and Old Equipment Virtual Conference, visit https://www.nawic.org/nawic/ Exposition (POSTPONED UNTIL 2021) Annual_Conference.asp Dates: August 27 – 29, 2021 Instead of being held this August, it has been rescheduled for August ASSOCIATED BUILDERS AND CONTRACTORS (ABC) 2021, at the same location near Concordia, Kansas, with the same ABC Convention 2020 outstanding attractions. Dates: August 17 – 19, 2020 Thank you for your patience and understanding. Be well, and see you Place: Music City Center at the 2021 Convention! 201 Fifth Avenue South, Nashville, TN 37203 ABC members are building Music City, and its the perfect backdrop SHEET METAL & AIR CONDITIONING CONTRACTORS’ NATIONAL for ABC Convention 2020. Nashville, a top convention destination known for its honky-tonks, food and arts scene, is also a great place ASSOCIATION (SMACNA) to get inspired by keynote speakers, network with ABC peers and cel- The SMACNA Edge Conference: A Virtual Education Forum October 13 – 15, 2020 ebrate the accomplishments of merit shop contractors from across Dates: With member health and safety top of mind, SMACNA has cancelled the country. Registration for ABC Convention 2020 is open to ABC members, the 2020 Annual Convention planned for Colorado and is now offerchapter staff and guests sponsored by a member or chapter. If you ing The SMACNA Edge Conference, A Virtual Education Forum, are a nonmember interested in attending, please email October 13-15, 2020. This new virtual experience will provide amazing content, expert speakers and valuable information on the meetings@abc.org for more information. ABC Convention is a closed event. All attendees must be registered most relevant and important topics to members. and display an event badge to access to any of the ABC Convention For any questions regarding Convention cancellation, please contact John Franco at jfranco@smacna.org or Kristin De Guzman at events. Advanced registration will close on Monday, August 10. ABC is offering an attractive registration fee that incentivizes atten- kdeguzman@smacna.org. Keep up to date on this event at dees to take part in all elements of the August convention. The fee has www.smacna.org/annualconvention.

Events are subject to change, check websites for updates

Ritchie Bros.’ Sets Records The Easy Way To Advertise Your Equipment Run In Two Consecutive Issues – Black & White $135 • Color $195

Sentry Tires - Skid Steer and Wheel Loader Tires at Volume Buyers Prices! Call Company Wrench for Sizes & Pricing 15-16 EB Call 866-294-6103

1999 SmithCo 36 Ft Tub, New Paint, Brakes, Wet Kit Pump, Tank, Hoses, Cab Controls ..............$Call 15-16 AP Call Mike 319-470-8388

Here's how the BARGAIN ADS Work: • Supply us with a photo of a machine (one machine per Bargain Ad) and a maximum 20 word description, plus contact and phone number. • Either email your copy & photo to: production@cegltd.com, or mail to: Construction Equipment Guide, 470 Maryland Drive, Ft Washington, PA 19034. • Cost is $135 per ad, $60 additional for color. • Your ad will run for two consecutive issues in 1 region.

NATION’S LEADING EXTREME SERVICE SPECIAL APPLICATION BUCKETS Hundreds in Stock - Variety Sizes - Many Models Call Emilee 218-863-6444 Email: ai@attachmentsintl.com 15-16 AP

For more information, call Construction Equipment Guide today at

800/523-2200

Ritchie Bros. set a new record, selling more than 35,000 equipment items and trucks in 29 online auctions across five countries in just five days — making it the busiest week ever in the company’s 60-plus year history. With all auctions held online due to the COVID-19 pandemic, Ritchie Bros. also set new online traffic records, with more than 2.5 million visits to its online platforms in five days (June 22 to 26). This includes the company’s busiest day ever on June 24, when the company hit more than 212,000 visits to rbauction.com in a single day. “We continue to see record attendance at our auctions around the world as more and more of our customers get used to participating in our auctions online,” said Ann Fandozzi, CEO, Ritchie Bros. “With big, multi-day auctions in Edmonton, Houston and Northeast, as well as 26 other auctions last week, we registered a staggering 80,000+ bidders in a week. Our people are working incredibly hard to ensure we deliver for our customers during these difficult times.” Total gross transaction proceeds for the record-breaking week surpassed more than $295 million, including a $43+ million auction in Houston, Texas; a $47-plus million

Northeast Regional auction; and $69-plus million Edmonton, AB auction. Houston, Texas, auction — More than 9,100 bidders from 61 countries registered to bid for the June 23 to 24 Houston auction. Approximately 47 percent of the equipment was purchased by out-of-state buyers from as far away as Vietnam, Poland and the United Arab Emirates. Highlights from this auction included a 2015 Tadano GR-750XL 75-ton rough-terrain crane (Lot 302) that sold for $350,000 to a buyer from California and a 2014 Caterpillar D6N LGP dozer (Lot 214) that sold for $150,000 to a buyer from Texas. Northeast Regional auction — With its first-ever Northeast Regional event, Ritchie Bros. combined equipment from four locations — North East, Md.; North Franklin, Conn.; Pittsburgh, Pa.; and Williamsport, Pa. — into one auction. More than 5,700 items were sold in the June 23 to 24 Northeast event, including a 2013 Caterpillar 825H soil compactor (Lot 860 S) that sold for $325,000 to a buyer from North Carolina and a 2015 Comacchio MC22AHT crawler blast hole drill (Lot 1104) that sold for $260,000 to a buyer from New York. In total, more than 7,900 bidders from 64 countries registered for the two-day auction. 

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 45

Page 46 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

ADVERTISER INDEX To read articles about these CEG advertisers, visit www.constructionequipmentguide.com 4 RIVERS EQUIPMENT....................................................................2

TEXAS SUPPLEMENT

AMULET .....................................................................................30,32

BANE MACHINERY ........................................................................24

BANDIT INDUSTRIES INC .............................................................19

BEE EQUIPMENT SALES LTD ......................................................15

BARGAINS ......................................................................................44

COMPACT CONSTRUCTION EQUIPMENT ...................................5

CEG SCALE MODELS....................................................................14

CONSTRUCTION EQUIPMENT GUIDE ........................................16

CONSTRUCTION EQUIPMENT GUIDE..............................22,41,45

GIL'S HEAVY EQUIPMENT REPAIR..............................................15

DITCH WITCH OF ARIZONA..........................................................11

GOMACO CORP.............................................................................17

DOOSAN PORTABLE POWER ........................................................7

GORILLA HAMMERS........................................................................1

ESCO CORP ...................................................................................31

HIGH TECH INDUSTRIES................................................................1

FELLING TRAILERS .......................................................................40

J & B PAVELKA INC........................................................................19

FISHER TOOLS ................................................................................9 FLANGE LOCK..................................................................................2 FLUID CONTROL SERVICES ........................................................12 HENDRIX MACHINERY LLC............................................................3 HITACHI CONSTRUCTION MACHINERY ...............................34,35 JAMES G MURPHY CO KENMORE WA .......................................................................43 KIRBY-SMITH MACHINERY INC....................................................48 KOBELCO CONSTRUCTION MACHINERY ............................26,27 KOMATSU AMERICA CORP .....................................................36,37 KPI-JCI.............................................................................................18

KIRBY-SMITH MACHINERY INC......................................................7 MCCOURT EQUIPMENT INC ........................................................21 NUECES POWER EQUIPMENT ...............................................11,19 POWERSCREEN TEXAS ...............................................................13 ROMCO EQUIPMENT CO................................................................2 SMITHCO ........................................................................................23 TROPHY TRACTOR .........................................................................3 VERMEER OF TEXAS-LOUISIANA .................................................9 WAUKESHA-PEARCE INDUSTRIES INC .....................................12 WYLIE IMPLEMENT .......................................................................15

LABOUNTY MANUFACTURING INC.............................................33 LINK-BELT EXCAVATORS.........................................................24,25

UTAH SUPPLEMENT

MAGELLAN CONSTRUCTION.......................................................38

CENTURY EQUIPMENT...................................................................3

MANITOWOC CRANE GROUP .....................................................47

HONNEN EQUIPMENT CO..............................................................4

METSO MINERAL CRUSHING .................................................16,17

HOWE RENTAL & SALES ................................................................3

METSO MINERALS SCREENING .................................................23

ICM SOLUTIONS ..............................................................................8

NORAM.......................................................................................12,13

KOMATSU EQUIPMENT CO............................................................2

ROADTEC INC ..................................................................................5

PIRTEK ..............................................................................................7

SCREEN MACHINE INDUSTRIES.................................................21

RASMUSSEN EQUIPMENT CO ......................................................5

SUPERIOR EQUIPMENT ...............................................................10

UTAH TRACK AND WELDING .........................................................1

TEREX CRANES...............................................................................6

WESTERN STATES EQUIPMENT COMPAN ..................................7

The Advertisers Index is printed as a free editorial service to our advertisers and readership. Construction Equipment Guide is not responsible for errors or omissions.

CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • July 19, 2020 • Page 47

Kirby-Smith Machinery, Inc. www.kirby-smith.com Oklahoma City, OK 800-375-3339 McAlester, OK 918-310-1550 Tulsa, OK 800-375-3733 Kansas City, KS 877-851-5729 St. Louis, MO 866-279-1392

Western Pacific Crane & Equipment www.wpcrane.com 8600 Calabash Ave. Fontana, CA 92335 562-286-6618 Fax: 909-356-1340 275 W. Larch Road Tracy, CA 95304 209-597-3824

Manitowoc delivers: Cranes ranging fro om 73 t (80 USt) to 2300 t (2535 USt) Capacity-enhancin ng VPC-MAX® technology and MAX-ER® attachments ments

He H eigh htt abo ov ve gr g oun o nd m

Manitowoc crawler cranes are built to o deliver unsurpassed productivity and a value on the most ch hallenging jobsites. 60,0

60 56

54,0

52 48,0

48 44

42,0

40 36,0

36 32

30,0 30

28 24 20

Optional long-reac ch booms, fixed jibs, luffing jibs and extended upper bo oom points

16 12

8,24 m TAILSWING TAILSWING

New 3.5 m wide boom oom inserts inser for MLC300 and MLC650

19602 60th Avenue NE Arlington, WA 98223 253-254-7950

1,52m 2,67 m

91-210 Kalaeloa Blvd. Kapolei, HI 96707 808-682-7263 6720 Arctic Blvd. Anchorage, AK 99518 855-342-7263 3521 Alken Street Bakersfield, CA 93308 855-927-2637 8912 NE Vancouver Way Portland, OR 97211 971-202-4002

HE-Equipment.com 877-HE-CRANE Full-Service Crane Hubs Dallas, TX 972-986-0910 Houston, TX 713-433-6411 Phoenix, AZ 602-232-0660 Salt Lake City, UT 801-297-8500 Service Center Billings, MT 406-259-9720

Access current Manitowoc crawler crane load charts at www.cranelibrary.com

Manitowoc MLC650 — features the ne w 3.5 m w id e b o o m s y s t e m t o r e a c h h ig h e r a n d increase capacit y.

w www .manitowoc.com

Page 48 • July 19, 2020 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE

Sale es • Rentals • Parts • Service • Fiinancing

2016 Komatsu D65PX-18 D KM16294X X

$219,500 5,,800 hrs.

2018 Komatsu WA500-8 A

2015 Wirrtgen WR200XLI

KM18 8423X

W WR15004X

CT14025X

$369,500 0 904 hrs.

$279,5 500 2,300 hrs.

$21 19,750 2,600 hrs.

2006 Koma atsu D41E-6

2014 Kom matsu D39PX-23

2014 Komatsu 2 PC360LC-10

6518X 3,904 hrs.

K KM14199X

$89,5 500 2,700 hrs.

2014 C Caterpillar D6T XW

2015 Komatsu PC138USLC-10

KM14056X

KM15152X

$13 32,500 5,500 hrs.

$109,500 3,610 hrs.

2017 Deere 644k

2013 Caterpillar 320E

2001 Caterrpillar 972G

2015 Kom matsu WA270-7 A

2016 Komatsu K WA470-8 A

CT13008X X $102,750 6,,388 hrs.

CT01023X $64,500 31,588 hrs.

KM15410M K $114,5 500 3,900 hrs.

KM16433X

JD17003X

$15 52,000 7,045 hrs.

$119,500 7,094 hrs.

2014 Kawasaki 80Z 7

2017 Deerre 310LEP

2012 Joh hn Deere 772G

2014 4 LeeBoy 8510C

2015 15 Komatsu HM400-5

KC14029X $59,500 12,046 hrs.

JD17 7010J $69,500 1,400 hrs.

JD12015X J $119,5 500 6,140 hrs.

LB14006X $79,500 2,217 hrs.

$459,500 7,800 hrs.

KM15268M

All sales are subject to availability at time of order, prices do o not include taxes or other applicable e fees. Kirby-Smith Machinery Inc. doesn’ oesn’t engage in exports to embargoed oed countries. Sold As Is Where Is.

Abilene • Amarillo • Dallas • Ft. Worth o • Kansas City • Lubboc ck • McAlester • Odessa a • Wa aco • Oklahoma City ity • St. Louis • Tulsa u

Contact Terry e y Ly yness s for details s and p pricing. ng. Follow us on

877.54 49.7501