Skip to main content

OCR Gateway GCSE (9-1) Physics Student Book sample pages

Page 1

Physics – Simple circuits (P3.2)

Electric circuits and potential difference

KEY WORDS parallel potential difference (p.d.) resistance voltmeter

Learning objectives: • know circuit symbols • recall that current (I) depends on resistance (R) and potential difference (V) • explain how an electric current passes round a circuit.

An electrostatic charge can build up in the air as a thunderstorm forms. The potential difference between a thundercloud and the ground can be up to 100 000 000 volts.

switch (open)

1

Draw a simple circuit containing a cell and a variable resistor.

2

The symbol for a light-emitting diode (LED) is a diode with two short parallel lines pointing outwards, representing light. Use the same logic to suggest what ‘LDR’ stands for and what an LDR does.

Potential difference Potential difference (p.d.) is the energy transferred per unit charge as charges move between two points in a circuit. It is measured in volts (V) using a voltmeter. A voltmeter is always connected across the component. We say the voltmeter is connected in parallel (Figure 3.8). A voltmeter has a very high resistance so almost no current can flow through it. For an electric current to flow, there needs to be a complete loop and a source of potential difference. Potential difference is sometimes referred to as voltage. V = IR = 2 × 5 = 10 V. 1 volt is the energy transferred when 1 coulomb of charge moves through a component. 1 V = 1 J/C. If a 12 V battery is used to light a lamp, each coulomb of charge going from the battery receives 12 J of energy.

106

OCR Gateway GCSE Physics: Student Book

Write two things that are needed for there to be an electric current.

4

A 6 V battery passes a current of 1 A through a lamp for 1 minute. Calculate how much energy is transferred from the battery to the lamp.

+

+

3.3 +

Current, resistance and potential difference Electrons are ’pushed’ around a circuit by a battery. They bump into the metal ions in the resistor. This makes the metal ions vibrate more so the resistor gets hotter. The increased vibrations of the ions held in their fixed lattice make it harder for the electrons to travel through the resistor, so its resistance increases (Figure 3.9).

switch (closed)

Electric circuits and symbols In order for a current to flow, a complete circuit must be formed. Also, a source of energy is needed to drive the current. This source of energy can be a simple electrical cell, a battery of cells or a power supply connected to the mains electricity. In a simple (series) circuit, the current that is measured at any point has the same value. This is because no electric charge that flows ‘leaks’ out of the circuit. We can use this energy transfer in an electrical circuit in a number of useful ways. Devices have been designed that can transfer energy as heat (electric bar heaters), light (lightbulbs and LEDs) and movement (electric motors). Each device is given its own symbol so that clear and complete circuits can be drawn. The symbols for the devices that you need to know about are shown in Figure 3.7.

3

A

V Figure 3.8 Measuring the p.d. across a resistor using a voltmeter

cell + battery metal ions in the resistor diode resistor

variable resistor

LED lamp

variable resistor

electrons collide with the metal ions

Figure 3.9 The movement of electrons in a wire carrying a current

The filament in a lamp connected in a circuit becomes so hot it emits light. Note that the net direction in which the electrons move is opposite to the direction of the conventional current. The conventional current direction, from positive to negative, was well established before scientists understood that the electrons actually moved from negative to positive. So they did not change it.

fuse

voltmeter

5

Why might the resistor in Figure 3.8 get warm?

6

The circuit shown in Figure 3.11 includes a variable resistor. Explain how the variable resistor can be used as a dimmer switch.

Figure 3.10 Circuit with variable resistor and lamp

DID YOU KNOW? Superconductors are materials that have an electrical resistance of zero at very low temperatures. No battery is needed to maintain a current.

A +

ammeter

V

thermistor

Figure 3.11 LDR

Figure 3.7 Circuit symbols

Current, I, resistance, R and potential difference, V are linked by the equation:

7

Calculate the resistance of a car headlamp when the supply potential difference is 12 V and the current is 3 A.

8

Calculate the potential difference across a 6 Ω resistor when the current through it is 1.5 A.

potential difference, V = current I × resistance, R

(in volts, V)

(in amperes, A) (in ohms, Ω) V = IR

Example: Calculate the potential difference across a 5 Ω resistor when the current through it is 2 A.

Google search: ‘superconductors, variable resistor (rheostat)’

107


Physics

4

MAGNETISM AND MAGNETIC FIELDS IDEAS YOU HAVE MET BEFORE:

IN THIS CHAPTER YOU WILL FIND OUT ABOUT:

PERMANENT MAGNETS

WHAT IS A MOTOR AND HOW DOES IT WORK?

• Permanent magnets are made from nickel, cobalt and most steels. • Iron is a magnetic material but loses its magnetism when the magnetising force is removed. • Like poles repel and unlike poles attract. • Repulsion is the only test for a magnet.

• Describe some uses of motors. • Explain how a motor works. • Explain how a commutator is used.

S

N

N

S

coil

N

• D.c. generators are similar in construction to d.c. motors. • A coil is rotated in a magnetic field. This induces an alternating current in the coil. • Direct current like that from a battery is obtained by using a commutator.

electric current

brushes

• The wires carrying an electric current produce a magnetic field. • The magnetic field made by the current in a wire is a circular shape around the wire. • The magnetic field is increased if more turns are wound on the coil and/or the current in the wire is increased.

• A transformer changes the size of an a.c. potential difference. • Step-up transformers increase the potential difference. • Step-down transformers decrease the potential alternating potential difference. difference supply

HOW ARE ELECTROMAGNETS USED?

• A coil of wire with an iron rod in it makes an electromagnet. • The iron rod becomes magnetised when a current flows in the coil. • The iron rod becomes strongly magnetised but loses its magnetism as soon as the current is switched off.

• A moving-coil microphone produces a changing electric current in response to sound waves. • A moving-coil loudspeaker produces sound waves in response to a changing electric current.

OCR Gateway GCSE Physics: Student Book

S split-ring commutator

primary coil

ELECTROMAGNETS

magnetic field axle rotated

coil

WHAT IS A TRANSFORMER?

circular magnetic field around wire

force (motion)

N

MAGNETIC EFFECT OF A CURRENT

direction of current

S split-ring commutator

HOW CAN A MAGNETIC FIELD BE USED TO PRODUCE AN ELECTRIC CURRENT?

• The Earth’s magnetic field is very similar to the magnetic field due to a bar magnet. • A compass uses the Earth’s magnetic field to indicate magnetic north. • The Earth behaves as if there is a gigantic bar magnet inside it.

magnetic field

electric current carbon brushes

EARTH’S MAGNETISM

134

rotation produced

force (motion)

secondary coil

soft-iron core

Magnetism and magnetic fields

135


Physics – The electromagnetic spectrum (P5.2)

The electromagnetic spectrum Learning objectives: • recall the similarities and differences between transverse and longitudinal waves • recognise that electromagnetic waves are transverse waves • describe the main groupings and wavelength ranges of the electromagnetic spectrum.

KEY WORDS longitudinal wave transverse wave spectrum electromagnetic waves visible spectrum

Electromagnetic waves are different from other waves because they do not need a material. They can travel through a vacuum. This is a special property of electromagnetic waves, which enables light and infrared waves to reach us from the Sun. All electromagnetic waves travel at the same speed in a vacuum: 3.0 × 108 m/s. 3

What are the similarities and differences between transverse and longitudinal waves?

4

Explain how waves in the electromagnetic spectrum are different from other waves.

5

What properties do all electromagnetic waves have in common?

All electromagnetic radiation from the Sun (including visible light) travels the 149 million kilometres to the Earth in about 8 minutes.

The electromagnetic spectrum

Transverse and longitudinal waves

Figure 5.28 shows that electromagnetic waves span a wide, continuous range of wavelengths and frequencies. transverse wave

1 2

compressions

1

10-1

106

107

108

109

10-2

microwaves

10-3

10-4 10-5 10-6

10-7 10-8 10-9 10-10 10-11 10-12

visible light

101

infrared

ultraviolet

X-rays

gamma rays

1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020

frequency and energy increase

Figure 5.26 Comparing transverse and longitudinal waves Figure 5.28 The wavelengths and frequencies of waves in the electromagnetic spectrum

Explain what is meant by (a) the amplitude and (b) the wavelength of a wave.

The groups of waves in the electromagnetic spectrum and their wavelengths are :

Give an example of a longitudinal wave.

• • • • • •

We know light is a wave because it has the same properties as other waves: it can be reflected and refracted. White light is a mixture of waves with different wavelengths which we see as different colours. These colours can be separated into what we call the visible spectrum. When scientists investigate the visible spectrum they can detect invisible waves on both sides, showing that the visible spectrum is really part of a much wider spectrum, which we call the electromagnetic spectrum. All the waves in the electromagnetic spectrum are transverse waves with many properties in common with visible light. Just like other waves, all electromagnetic waves transfer energy from one point to another. In electromagnetic waves, electromagnetic fluctuations occur at right angles to the direction in which energy is being transferred by the wave. Some waves need a material to travel through. For example, sound waves can travel through air, liquids and solids but not a vacuum. Water ripples travel along the surface of water. OCR Gateway GCSE Physics: Student Book

105

102

ultra high frequency

104

Frequency (Hz)

Electromagnetic waves

180

long-wave radio

longitudinal wave

wavelength increases 103

very high frequency

104

shortwave radio

Wavelength (m)

mediumwave radio

As you saw earlier, there are two types of waves: transverse and longitudinal. In a transverse wave the vibrations are at right angles to the direction of energy transfer and in a longitudinal wave they are parallel to the direction of energy transfer (Figure 5.26). Ripples on water (Figure 5.27) and a rope or Slinky moved from side to side are transverse waves.

5.9

Figure 5.27 Water waves are transverse: although it looks as if the water particles move outwards they actually move up and down

radio, TV and microwaves: above 105 m to 10 –3 m infrared: 10 –3 to 10 –7 m visible (red to violet): 10 –7 m ultraviolet: 10 –7 to 10 –8 m X-ray: 10 –8 to 10 –10 m gamma ray: 10 –10 to less than 10 –12 m.

The shorter the wavelength of the electromagnetic wave, the further it can travel through other materials. The higher the frequency of a wave, the more energy it can transfer to another object when the radiation is absorbed. 6

Which grouping in the electromagnetic spectrum has the highest frequency?

7

Ultraviolet light used in a sunbed has a wavelength of 3.5 × 10 –7 m. Calculate the frequency of this light.

8

Calculate the frequency of an electromagnetic wave with a wavelength of 20 cm. Use standard form for your answer.

9

Suggest why ultraviolet waves are more dangerous than radio waves.

REMEMBER! Remember the order of electromagnetic wave groupings.

KEY INFORMATION The shorter the wavelength (the higher the frequency) of an electromagnetic wave the more dangerous the radiation.

KEY INFORMATION All electromagnetic waves travel at the same speed in a vacuum, 3.0 × 108 m/s.

Google search: ‘electromagnetic waves, em spectrum’

181


Physics

Worked example

Check your progress You should be able to:

The table below shows the electromagnetic spectrum.

■■Describe the amplitude,

wavelength, frequency and period of a wave

■■Realise that waves can be transverse or longitudinal

➞

➞

■■Describe how sound waves travel through air or solids

➞

■■Draw a labelled ray diagram to illustrate reflection of a wave at a boundary

■■Describe the range of normal human hearing Define the term ultrasound

➞

➞

➞

➞

➞

■■Describe the hazardous

effects of gamma rays, X-rays ➞ and ultraviolet radiation

■■Give examples of the uses of the main groupings of the electromagnetic spectrum

➞

■■State that each colour in the visible spectrum has its own narrow band of wavelength

202

➞

sound and ultrasound.

transfer by waves (including electromagnetic waves)

➞

illustrate refraction at a boundary

➞

➞

➞

■■Explain the difference between

wavelength of a sound wave are indicated by the waveform on a CRO.

ripples on a water surface, it is the wave and not the water itself that travels

➞

■■Explain the risks associated

transfer by electromagnetic waves

absorb certain wavelengths and transmit other wavelengths the nature of the image formed by a lens

OCR Gateway GCSE Physics: Student Book

B

X-rays

gamma rays

State the names of the waves labelled A and B.

2

➞

F

produced

consequences of exposure to radiation

4

F

Explain why we see a red apple as red.

White light is a mixture of many wavelengths. We see the red apple because the red wavelengths are reflected off the apple. 5

Complete the wave front diagram to show the refraction of light from air to water.

■■Explain why each type of

electromagnetic wave is suitable for the application air

opaque object depends on which wavelengths are more strongly reflected

■■Use ray diagrams to determine ➞

O

The positions of the rays have been drawn correctly, but the virtual rays have not been drawn with dashed lines. Also the image has not been drawn in. You should always draw the image when you have completed the ray diagram.

through materials of different densities.

■■Explain that the colour of an ➞

This answer is a good start but is incomplete. It doesn’t give a full explanation. The answer should also say that we can use them by controlling the exposure dose.

Complete the ray diagram to show how the image is formed.

explain refraction in terms of a change in wave velocity

■■Evaluate the risks and ➞

X-rays are dangerous to humans. Explain how they can also be used in medical therapy without lasting harm.

We can use them for X-rays to see our bones and for treating cancer by killing the cancer cells. 3

Both answers are c­ orrect. Use a ­mnemonic to ­remember the correct order.

A = radio waves   B = ultraviolet waves

■■Use wavefront diagrams to

■■Describe how radio waves are

■■Describe examples of energy

infrared visible light

substances may absorb, transmit, refract or reflect electromagnetic waves in ways that vary with wavelength

■■Compare the groupings of

with the use of ionising radiation including ultraviolet radiation

1

microwave

■■Describe how different

■■Explain how ultrasound travels

waves can be used for medical ➞ and industrial imaging the electromagnetic spectrum in terms of wavelength and frequency

A

transverse and longitudinal waves

■■Describe how ultrasound

■■Use ray diagrams to determine ➞

equation

■■Describe evidence that, for e.g.

reflection, transmission and absorption of waves (including ➞ electromagnetic waves) at material interfaces

■■Construct ray diagrams to

■■Rearrange and apply the wave

■■Describe how the frequency and

■■Describe that colour filters

■■State that in a convex lens parallel rays of light are brought to a focus at the principal focus

and transverse waves

■■Describe examples of

■■Name the main groupings of

the electromagnetic spectrum

■■Give examples of longitudinal

➞

■■Give examples of energy

■■Understand that waves can

be absorbed, transmitted or reflected at a surface

v = l × f to calculate wave speed

■■Explain the difference between

■■Understand that waves

transfer energy or information

■■Use the wave equation

the position and magnification of images

water A

This is a good answer. Just one thing has been missed out: red wavelengths are reflected but what about the other wavelengths? They are absorbed.

The wave fronts being closer together is correct, but there is one crucial thing wrong. When waves go from a less dense medium to a denser medium, they are refracted towards the normal. The diagram shows them being refracted away from the normal. A wavefront should be unbroken - just bent on the air-water boundary.

Worked example

203


Physics – Beyond Earth (P8.3)

The Sun and other stars Learning objectives: • describe how the Sun and other stars formed • describe the nuclear fusion reactions in the Sun.

The Earth is approximately 150 million km from the Sun and it takes light from the Sun eight minutes to reach the Earth.

Stars and galaxies Our Sun is our nearest star. It is just one of billions of stars that make up our galaxy, the Milky Way. The Universe is made up of billions of galaxies, such as galaxy M74 (Figure 8.18). 1

KEY WORDS galaxy Milky Way nebula nuclear fusion protostar

Massive stars, however, have a different fate. At the end of this phase they expand into a red supergiant and then explode into a supernova, ending their time as a rapidly spinning neutron star or as a black hole. DID YOU KNOW?

2

State the materials a star is formed from.

3

States the force that pulls these materials together.

4

Explain why it takes millions of years to form a protostar.

5

Describe how a star is formed.

DID YOU KNOW?

Nuclear fusion

The Milky Way rotates around the central core of the galaxy. Astronomers believe that there is a black hole at the centre of the galaxy.

In Chapter 6 you learned that nuclear fusion occurs when two hydrogen nuclei join or fuse together to form a new nucleus of helium (Figure 8.21). This is only one of the fusion reactions in the Sun that releases energy. There are many other reactions as well. 1H 1

3 He 2

Put these bodies in order of size. Put the smallest object first: star, planet, galaxy, Solar System

The origin of stars

8.7 We normally measure temperature in degrees Celsius. In physics we use the kelvin scale. 0 K = –273 °C

DID YOU KNOW? The Sun releases about one billion (109) kilograms of particles into space each second. This creates a solar wind that creates the Northern Lights (Aurora Borealis) when these particles reach the Earth’s atmosphere.

fusion

Space is not just empty vacuum. Space contains huge clouds of dust, hydrogen and helium gas which are called nebulae (Figure 8.19). These are sometimes called the birthplaces of stars. Figure 8.18 Spiral galaxy M74, taken from the Hubble Space Telescope Average Star

Red Giant

Planetary Nebula

White Dwarf

Supernova

Black Hole

Figure 8.19 The Life cycle of a star

Over millions of years, gravity pulls the gas and dust together. As it compresses it get hotter until the core begins to glow and it becomes a protostar. Eventually it becomes so hot that the nuclei of atoms of hydrogen gas begin to fuse, which triggers the release of huge amounts of energy. At this point the core of the protostar ignites in a massive nuclear reaction. This is the moment when a star is formed. What happens then depends upon the size of the star. Average sized stars, like the Sun, eventually run out of hydrogen and expand to form a red giant. Glowing gases then swell up into a cloud called a planetary nebula. The gases escape and a tiny dense sphere called a white dwarf is all that remains.

274

OCR Gateway GCSE Physics: Student Book

Figure 8.22 The Aurora ­Borealis over Greenland

At 15 000 000 K the hydrogen nuclei move with such high speeds that they can fuse.

Massive Star Red Supergiant

Figure 8.21 Fusion of hydrogen nuclei in the Sun is one of the fusion reactions that release energy.

Since the nuclei are positively charged they repel each other. The energy needed to overcome the repulsion comes from the high temperatures created by the force of gravity compressing the gases.

Neutron Star

Stellar Nebula

2H 1

Figure 8.20 The Carina nebula

6

What element is the Sun mostly made up of?

7

Why do fusion reactions require extremely high temperatures?

8

Explain what happens in the nuclear fusion reactions inside the core of the Sun.

9

Suggest whether there is any helium in a protostar.

10

Why is it wrong to say that hydrogen is being burned in our Sun?

During periods of high solar activity, the Sun can eject massive amounts of plasma (very high temperature matter made up of separated nuclei and electrons). Sometimes, solar flares (Figure 8.23) can be so powerful that they can cause satellites in orbit around Earth to malfunction.

Figure 8.23 Solar flare

Google search: ‘gravitational collapse, radiation pressure’

275


Physics

MATHS SKILLS

MATHS SKILLS

A number in standard form is written as: where A is a decimal number between 1 and 10 (including 1 but not 10), and B is an integer.

Using scale and standard form Learning Objectives: • •

understand the scale of objects in the Universe use standard form.

When looking at the scale of the Universe, we need a different way of expressing the numbers involved – it becomes very difficult to understand the size of a number when there are lots of zeros in it.

Scale The Moon is one quarter the diameter of the Earth. That’s a ratio of 1 : 4. The Moon is the largest natural satellite of any planet in the Solar System. Mars is only about half the diameter of the Earth: a linear ratio of 1 : 2. The diameter of Jupiter, the largest planet, is eleven times that of the Earth, and its volume is over 1300 times greater than the Earth. The Sun’s diameter is 109 times greater than the Earth and 1 300 000 Earths could fit inside the Sun. When you draw a scale model of the Solar System, there are problems with sizes. If you made the Sun the size of a large beach ball, the Earth would be the size of a pea and stand 100 m from the beach ball. Jupiter would be the size of a tennis ball and 520 m from the beach ball. Neptune, the furthest planet from the Sun, would be 3 km away. If you want to represent the Solar System on a standard A4 sheet of graph paper, you need to take the longest distance, in this case to Neptune, and scale it down to fit the longest side of the paper. 1

Look at the data set in Topic 8.10. Draw a scale model of the distances of the planets to the Sun to fit on an A4 piece of paper.

Standard form The distance from the Sun to the Earth is about 150 000 000 km. The distance to Neptune is 4500 million km. The distance to Alpha Centauri is 41 000 000 000 000 km. And our Milky Way galaxy is 1 000 000 000 000 000 000 km in diameter. We handle such large numbers by expressing them in standard form.

290

OCR Gateway GCSE Physics: Student Book

8.15

A × 10B

KEY WORDS

Here are some examples:

scale standard form

1000 km = 1 × 103 km

KEY INFORMATION

This is because 1000 = 1 × 10 × 10 × 10. Distance to the Sun, 150 000 000 km = 1.5 × 10 km 8

To write 150 000 000 km in standard form, imagine moving a decimal point from the right hand side of the last zero to between the 1 and 5. We count how many places we have to move this digit: it is eight places to the left. Eight places moved to the left gives us an index of +8 so the answer is 1.5 × 108 km 



2 



Writing the distance to the Sun as 15.0 × 107 km is correct, but it is not in standard form because the first number is greater than 10.

Write the distances from the Sun to Neptune, to Alpha Centauri, and the diameter of the Milky Way in standard form.

Another way of handling such large numbers is to use a larger unit. Astronomers use the light year, which is the distance light will travel in a year of 365 days.



  

3

 

a Calculate how far will light travel in a year. (Speed of light is 3.0 × 108 m/s.)

 

b Use your answer to calculate the diameter of the Milky Way in light years.

 

  

  

  

Figure 8.50 The Sun and planets (including the dwarf planet Pluto), not to scale

DID YOU KNOW? There is a scale model of the Solar System on the south side of York. The sizes of the Sun and planets and the distances between them are all to the same scale. The model is about 10 km long! You can walk between the Sun and planets. There is also a scale model at Anstruther in Scotland.

Negative powers of ten for very small numbers Very small numbers can also be written in standard form. For example, the radius of an atom is about 1 × 10 -10 m. A negative power of ten means a number less than 1. In standard form, 1/1000 is 1 × 10 –3, 1/1 000 000 is 1 × 10 –6 and 1/1 000 000 000 is 1 × 10 –9. These correspond to the SI prefixes milli, micro and nano. 4

The change in wavelength (red-shift) for light from a receding galaxy is 170 nm. Write this in metres, in standard form.

5

Here are some approximate volumes:

Figure 8.51 Artist’s concept of the Milky Way

proton = 1 × 10 – 45 m3 person = 1 m3 Solar System = 1 × 1039 m3 a Calculate how many times bigger a person is, compared with a proton inside them. b How much bigger is the Solar System compared with a person? c If a proton was scaled up to the size of a person, and the person was scaled up by the same factor, how many Solar Systems would the volume of the person be?

Google search: ‘York solar system model, Anstruther solar system model’

291


Turn static files into dynamic content formats.

Create a flipbook