Neoferma International 2016

Innovation @work

SPECIALIST WATERPROOFING SYSTEMS AND DESIGN FOR BASEMENT TANKING AND SALTWATER ENVIRONMENTS AUSTRALIA, UNITED ARAB EMIRATES, THE MIDDLE EAST www.neoferma.com

Disclaimer: These observations are provided in order to assist in the waterproofing and related tasks and offer some possible solutions to the situation. They are not intended for any other purpose nor should be used as a proposal or recommendation to be acted on without the approval of a qualified engineer.

We accept no liability/responsibility to any recipient; recipient company or any third party who may suffer any damage including physical or fiscal as a result of the use or reliance upon the whole or any part of this document.

www.neoferma.com

NEO-UAE-Green 2016 02v1

Neoferma has been established in Australia since 1986 producing a range of specialist systems and products for the construction industry. Working closely with Engineers and Contractors to produce designs and systems that meet the most demanding of situations – waterproofing structures below the water table.

These systems and designs have become integral in the successful waterproofing of major projects in testing conditions – in sand and deep basements directly on the sea shore or banks of waterways especially on the rapid developing coastal areas such Australia and the UAE. The SwellSeal Waterproofing Range.

SwellSealMS Bentonite Membrane: Purpose designed for the construction industry. Multi System combining premium bentonite membrane with two hundred micron Polyethylene liner.

SwellSeal Ultra Bentonite Membrane: Formulated for use with Salt Water environments with far greater swelling capacity of other Bentonite products in contaminated/salt water environments.

JointStop BN: Hydrophillic bentonite strip for the sealing of construction joints in concrete in contact with salt and brackish water.

JointStop HR: Hydrophilic rubber waterstops for construction joints.

X-Seal HR: For maximum protection of joints in areas of high risk due to thermal movement.

X-Gel: A range of high performance injection gels for concrete repair in new or old structures.

Westox Cocoon System: Removal of salts from concrete and masonary by osmosis. Proven in World Heritage sites and commercial structures.

Ecobust: An effortless, extremely powerful expansive grout to demolitish rock & concrete that is safe & environmentally friendly. Ecobust eliminates noise, dust and vibration, ideal for use in sensitive areas where any form of combustion is not permitted or major areas such as quarries.

www.neoferma.com

SWELLSEAL MS 5500 GCL with 200 Micron PE Bonded Liner SWELLSEAL Multi System / High Pressure (MS/HP) is a waterproofing membrane composite made from high quality polypropylene geotextiles encaptulating premium grade sodium bentonite granules.

SWELLSEAL MS is fully fibre-reinforced with American needle-punching (American) across the full length and width of the product. SWELLSEALMS HP has a 200 micron PE(Polyethylene) sheet backing bonded to the geotextile.

DESCRIPTION

VALUE (Average) 2

TEST METHOD

SwellSeal MS / HP has more bentonite granules per m than many

Geotextile Components other waterproofing Non–Woven Geotextile massmembranes. (gm/m2) 235 ASTM D5261 2 130 ASTM D5261 Woven Geotextile mass (gm/m ) SWELLSEAL Clay Component MS is designed for use in situations requiring protection Bentonite Layer (gm/m2) ASTM D5993 against contaminated or saline water as well as areas5500 affected by certain Swell Indexsuch (ml/ 2g) 28 ASTM D5890 gases as methane.

Fluid Loss (ml) <18 ASTM D5891 GCL component with Non-Woven and Woven Geotextile SWELLSEAL MS can be tailored to your project and specifications: Thickness (mm) 7 ASTM D5199 P.E Liner Thickness 0.20 ASTM D5199 Moisture Content (%) (HP) grades with PE layer. <20 ASTM D4643 • High Pressure Peel Strength (N) 145 ASTM D4632 -12 ASTM D5084 Hydraulic / Permeability (m/s) PE layering. 4.5 x 10 • LowConductivity Pressure (LP) grades without Tensile Strength (KN/m) 10 ASTM D6768 ASTM D6766 GCL• 5500 Compatibility @ 35of kPa test continuing 8 x 10-8 cm/s gms Mass Bentonite per m2 Internal Shear Strength (kPa) at 2.22 kN Normal Load > 37 Peak ASTM D6243 GCL with PE Bonded Liner (PE side subjected to test) • Grade of Geotextile Total weight of SwellSeal MS (with HDPE liner) 6000 ASTM D5261 Puncture Resistance (N) 475 ASTM D4833 Size of Roll, 1.65 x (N) 20m(up to 6 metres width available) Peel• Adhesion to Concrete 58 (MD, TD) ASTM D903 Hydrostatic Pressure Resistance @ 689.5 kPascal (70.5 Passed ASTM D5385 • Salt water formulae meters head pressure) Water Adsorption (% change in Mass) 3.50 ASTM D471 Passed ASTM&C836 Crack Bridging, at -26 o Cincl’g Bentonite waterstops, • Full range10ofcycles accessories detailing pastes o Passed ASTM D1970 Lowinjectable Temperature Flexibility @ -20 C ; MD , TD hoses Resistance to Decay, 28 days (% retained) 110 ASTM E154 Accelerated Aging, 2000 hrs (% retained) 67 ASTM G154 0.01253 ASTM E96 Water Vapour Transmission gm/hr-m2

Designed and formulated in Australia to Neofema specifications.

www.neoferma.com

Test Results DESCRIPTION VALUE (Average) (Swellseams MS + PE Layer) Geotextile Components DESCRIPTION VALUE Non–Woven Geotextile mass (gm/m2) 235 (Average) 130 Woven Geotextile massDESCRIPTION (gm/m2) Geotextile Components VALUE Clay Component (Average) Non–Woven Geotextile2 mass (gm/m2) 235 Bentonite Layer (gm/m ) (gm/m2) 5500 Geotextile Components VALUE Woven Geotextile massDESCRIPTION 130 Swell Index (ml/ 2g) 28 (Average) Non–Woven Geotextile mass (gm/m2) 235 Clay Component 2 2 Fluid Loss (ml) <18 Geotextile Components DESCRIPTION VALUE 130 Woven Geotextile mass) (gm/m ) Bentonite Layer (gm/m 5500 GCL component with Non-Woven Non–Woven Geotextile mass (gm/m2and ) Woven Geotextile (Average) 235 Clay Component Swell Index (ml/ 2g) 28 Thickness (mm) 7 Geotextile Components 130 Woven Geotextile mass2) (gm/m2) Bentonite Layer (gm/m 5500 Fluid Loss (ml) <18 DESCRIPTION VALUE 2 P.E Liner Thickness 0.20 Non–Woven Geotextile mass (gm/m and ) Woven Geotextile 235 Clay Component Swell Index (ml/ 2g) 28 GCL component with Non-Woven (Average) Moisture Content (%) <20 130 Woven Geotextile mass2) (gm/m2) Bentonite Layer 5500 Fluid Loss (ml) (gm/m <18 Thickness (mm) 7 Peel Strength (N)2g) 145 Geotextile Components Clay Component SwellLiner Index (ml/ 28 GCL component with Non-Woven and Woven Geotextile P.E Thickness 0.20 2 2/ Permeability Hydraulic Conductivity (m/s) 4.5 x710 -12 Layer (gm/m ) 5500 Non–Woven Bentonite Geotextile mass ) 235 Fluid LossContent (ml) <18 Thickness (mm) Moisture (%)(gm/m <20 2 Non-Woven Tensile Strength (KN/m) 10 SwellLiner Index (ml/ 28 Non-Woven Component Geotextile GCL component with and Woven Geotextile 130 P.E Thickness 0.20 Peel Strength (N)2g) 145 ) and Woven Woven Geotextile mass (gm/m -8 -12 GCL Compatibility @ 35 kPa test continuing 8 x 10 Fluid Loss (ml) <18 Thickness (mm) 710cm/s Moisture Content (%) <20 Hydraulic Conductivity / Permeability (m/s) 4.5 x Clay Component Internal Shear Strength (kPa) at 2.22 kN Normal Load > 37 Peak GCLLiner component with Non-Woven and Woven Geotextile P.E Thickness 0.20 Peel Strength 145 Tensile Strength 10 2 (N)(KN/m) Bentonite Layer ) Bonded Liner (PE side subjected to test) 5500 -12 GCL(gm/m withContent PE Thickness (mm) Moisture (%) <20 Hydraulic Conductivity / Permeability (m/s) x7-810cm/s GCL Compatibility @ 35 kPa test continuing 84.5 x 10 Swell Index (ml/ 2g) 28 TotalLiner weight of(N) SwellSeal MS (with HDPE liner) Load 6000 P.E Thickness 0.20 Peel Strength 145 Tensile Strength (KN/m)(kPa) 10 Internal Shear Strength at 2.22 kN Normal > 37 Peak -12 Puncture Resistance 475 Fluid Loss (ml) <18 Moisture (%) <20 Hydraulic Conductivity /Liner Permeability (m/s) x -810cm/s GCL Compatibility @(N) 35 kPa(PE test side continuing 84.5 x 10 withContent PE Bonded subjected to test) Adhesion to Concrete (N) 58 (MD, TD) Peel 145 Tensile Strength (KN/m) 10 GCL component with Non-Woven and Woven Geotextile Internal Shear Strength (kPa) at 2.22 kN Normal Load > 37 Peak Total Strength weight of(N) SwellSeal MS (with HDPE liner) 6000 -12 -8 Hydrostatic Pressure Resistance @ 689.5 kPascal (70.5 Passed Hydraulic Conductivity / Permeability (m/s) 4.5 x 10 GCL Compatibility @ 35 kPa test continuing 8 x 10 cm/s with PE Bonded Liner (PE side subjected to test) Puncture Resistance (N) 475 Thickness (mm) 7 meters head pressure) Tensile Strength (KN/m) 10 Internal Shear Strength (kPa) at 2.22 kN Normal > 37 Peak Total weight of SwellSeal MS HDPE liner) Load 6000 Peel Adhesion to Concrete (N)(with 58 (MD, TD) P.E Liner Thickness 0.20 -8 Water Adsorption (% change in Mass) 3.50 Compatibility @ 35 kPa test continuing 8 x 10 GCL with PE Bonded Liner (PE side subjected to test) Puncture Resistance 475cm/s Hydrostatic Pressure (N) Resistanceo @ 689.5 kPascal (70.5 Passed Moisture Content (%) <20 CHDPE Crack Bridging, 10Concrete cycles at(N) -26 Internal Shear Strength (kPa) at 2.22 kN Normal >Passed 37 Peak Total weight of SwellSeal MS (with liner) Load 6000 meters head pressure) Peel Adhesion to 58 (MD, TD) o Peel Strength (N) 145 C ; MD , TD Passed Low Temperature Flexibility @ -20 Woven Component with PE Bonded Liner (PE side tested) GCL with PE Bonded Liner (PE side subjected to test) Puncture Resistance 475-12 Water Adsorption (%(N) change in Mass) 3.50 Passed Hydrostatic Pressure Resistance @ 689.5 kPascal (70.5 Resistance Decay, 28 days (%o retained) 110 TD) Hydraulic Conductivity /of Permeability (m/s) 4.558xPassed 10 Total weight SwellSeal MS (with 6000 meters headto pressure) Peel to (MD, CHDPE liner) CrackAdhesion Bridging, 10Concrete cycles at(N) -26 o Accelerated Aging, 2000 hrs (% retained) 67 Puncture Resistance 475 Water Adsorption (%(N) change Mass) 3.50 Hydrostatic Pressure Resistance @ 689.5 Passed C2 ; MDkPascal , TD (70.5 Low Temperature Flexibility @in-20 Tensile Strength (KN/m) 10 o -8 0.01253 Water Vapour Transmission gm/hr-m meters head Peel to 58Passed (MD, TD) C CrackAdhesion Bridging, 10Concrete cycles at(N) -26 Resistance topressure) Decay, 28 days (% retained) 110 cm/s GCL Compatibility @ 35 kPa test continuing 8 x 10 o Water Adsorption (% change in Mass) 3.50 Hydrostatic Pressure Resistance @ 689.5 kPascal (70.5 Passed C ; MD , TD Low Temperature Flexibility @ -20 Accelerated Aging, 2000 hrs (% retained) 67 Internal Shear Strength (kPa) at 2.22 kNoNormal Load > 37 Peak meters headtopressure) C 2 Passed Crack Bridging, 10 cycles at gm/hr-m -26 Resistance Decay, 28 days (% retained) 110 0.01253 Water Vapour Transmission GCL with PELow Bonded Liner(% (PE side to test) o Water Adsorption change insubjected Mass) 3.50 C ; MD , TD Passed Temperature -20 Accelerated Aging,Flexibility 2000 hrs@ (% retained) 67 2 Total weight Crack of SwellSeal MS (with HDPE 6000 Bridging, 10 cycles at -26 Cliner) Passed Resistance to Decay, 28 days (%o retained) 110 0.01253 Water Vapour Transmission gm/hr-m o Puncture Resistance (N) 475 Low Temperature C ; MD , TD Passed Accelerated Aging,Flexibility 2000 hrs@ (%-20 retained) 67 2 Resistance to Decay, (% retained) 110 0.01253 Water Vapour Transmission Peel Adhesion to Concrete (N) 28 daysgm/hr-m 58 (MD, TD) Accelerated Aging, 2000 hrs (% retained) 67 Hydrostatic Pressure Resistance @ 689.5 kPascal (70.5 Passed Vapour Transmission gm/hr-m2 0.01253 meters headWater pressure)

Water Adsorption (% change in Mass) Crack Bridging, 10 cycles at -26 o C Low Temperature Flexibility @ -20 o C ; MD , TD Resistance to Decay, 28 days (% retained) Accelerated Aging, 2000 hrs (% retained) Water Vapour Transmission gm/hr-m2

3.50 Passed Passed 110 67 0.01253

TEST METHOD TEST METHOD ASTM D5261 ASTM D5261 TEST METHOD ASTM D5261 ASTM D5993 TEST METHOD ASTM D5261 ASTM D5261 D5890 ASTM ASTM D5891 TEST METHOD ASTM D5261 D5993 ASTM D5261 D5890 ASTM D5891 D5199 D5261 D5993 ASTM TEST METHOD ASTM D5199 ASTM D5261 D5890 ASTM D5891 D4643 D5261 D5993 ASTM D5199 ASTM D4632 D5890 ASTM D5199 ASTM D5891 D5084 D5993 ASTM D5261 D5199 ASTM D4643 ASTM D6768 D5890 ASTM D5199 D4632 ASTM D5261 ASTM D5891 D6766 D5199 ASTM D4643 D5084 ASTM D5199 D6243 ASTM D4632 ASTM D6768 D5993 D5199 ASTM D4643 D5084 D6766 ASTM D5890 D5261 ASTM D5199 D4632 D6768 D6243 ASTM D4833 ASTM D5891 D5084 ASTM D4643 D6766 ASTMD5261 D903 D4632 D6768 D6243 ASTM ASTM D5385 D5084 D6766 ASTM D4833 ASTM D5199 D6768 D6243 ASTM ASTMD5261 D903 ASTM D5199 ASTMD5385 D471 ASTM D6766 D4833 ASTM D4643 ASTM C836 ASTM D6243 ASTMD5261 D903 ASTM D4632 ASTM D1970 ASTM D4833 ASTMD5385 D471 ASTMD5261 E154 ASTM D5084 ASTM D903 ASTM C836 ASTM G154 D4833 ASTMD5385 D471 ASTM D1970 ASTM D6768 ASTMD6766 E96 D903 ASTM C836 E154 ASTM D471 ASTM D1970 ASTM D5385 G154 ASTM D6243 ASTM E154 ASTMC836 E96 D471 ASTM ASTM D1970 G154 ASTM ASTM C836 E154 ASTMD5261 E96 ASTM D4833 ASTM ASTM D1970 G154 ASTM ASTME154 E96 ASTM D903 ASTM G154 ASTM D5385 ASTM E96

ASTM D471 ASTM C836 ASTM D1970 ASTM E154 ASTM G154 ASTM E96

www.neoferma.com

www.neoferma.com

www.neoferma.com

Innovation work

@ Membrane Independent surveys have found that using a Bentonite System in place ofsurveys traditional has significant advantages Independent havewaterproofing found that using a Bentonite Membrane place of and traditional waterproofing hasthesignificant both inSystem speed ofinapplication the beneficial effect on construction advantages bothas in savings the speedinofthe application effect programme, as well overall and costthe ofbeneficial the waterproofing on the construction programme, as well as savings in the overall cost element. of the waterproofing element.

ADVANTAGES

SPEED OF PROGRAMME

Information based on independent Quantity Surveyors report, commissioned

by Abu Dhabi Developer.

www.neoferma.com

www.neoferma.com

Innovation Innovation@@work work WARRANTY WARRANTY WARRANTY warranties that protects your interests

Our products carry full at all stages; from the Our products carry full warranties that protects your interests at all stages; from the procurement process through to project weinterests can offeratextended warranty periods Our products carry full warranties that completion; protects your stages; from the procurement process through to project completion; wespecification can offer all extended warranty periods beyond our standard ten years subject to design, system and independant procurement process through to project completion; we can offer extended warranty periods beyond our standard ten years subject to design, system specification and independant inspection beyond our standard twenty years subject to design, system specification and independant inspection inspection

Manufacturer’s Product Q&A, Manufacturer’s Product Q&A, Material Warranty Material Warranty

Manufacturer’s Product Q&A, Material Warranty

Installation

Installation

Insured Warranty Performance in service against resultant damage

Installation Performance and Service Warranty Public Liability $20,000,000 against resultant damage.

Products Liability $20,000,000 Performance and Service Warranty Public Liability $20,000,000 Underwritten at Lloyds of London Goods in Custody $100,000 against resultant damage.

Warranty + Products Liability $20,000,000 Underwritten at Lloyds of LondonFinancial Loss $5,000,000 Loss $5,000,000 Performance and Service Warranty Financial

against resultant damage.

Underwritten at Lloyds of London

Public Liability Goods in Custody Products Liability Financial Loss Goods in Custody

$20,000,000 $100,000 $20,000,000 $5,000,000 $100,000

www.neoferma.com

BENTONITE TANKING SYSTEMS FAQS

How does Bentonite work as a waterproofing medium

Bentonite has many and varied uses, in this case by confining and compacting the clay the mineral swells against its self to form a watertight barrier.

What is the swell ratio of the sodium bentonite (the active waterproofing constituent) used in the system

Sodium Bentonite swells to 24 times its own dehydrated mass in clean water.

How many kilos of sodium bentonite per square meter of membrane

SwellSeal MS 5.50 kgs / m2. of granular bentonite.

What preparation of the subsoil is necessary

Although usually installed on a mud blinder, membrane can be installed on sand or ground compacted to a minimum of 85% modified Proctor.

Does the membrane need to be protected from the elements during construction

No. Membrane can withstand exposure without adverse effect for several weeks.

Does the membrane have to be sandwiched in a double blinder

No. Dry fill Bentonite does not require a topping blinder, however pre hydrated membranes do to avoid drying out and cracking.

Will the sodium bentonite react effectively in salt water or contaminated water

Salt water and Contaminated water conditions will effect the performance of Bentonite.

Laboratory test results show that SwellSeal will effectively self-heal.

Will the sodium bentonite remain evenly distributed in vertical applications

Yes. Pre hydration will activate the membrane prior to the pour to compensate for the local conditions.

Does the membrane need to be hydrated prior to the concrete pour

Yes. Our membranes are American needle punched to ensure that sodium bentonite does not creep thus creating weak areas.

Does the system have an insured warranty

Yes. Systems have a 20 year warranty on materials and workmanship. The warranty can be extended to 50 years on material and application, subject to system and installation approval.

In addition to the warranty we provide financial loss cover of $5,000,000

www.neoferma.com

Innovation @ work

www.neoferma.com www.neoferma.com

Innovation @ work

00 www.neoferma.com

Innovation @ work Innovation @ work

www.neoferma.com www.neoferma.com

™ TM

SWELLSEAL JOINTSTOP (BN) HYDROPHILIC BUTYL BENTONITE Product Description SWELLING CHART & INSTALLATION Hydrophilic Bentonite for in-situ concrete.

Uses A flexible butyl rubber and bentonite compound that swells upon contact with water to form a long-lasting compression seal in non-moving concrete joints. SWELLSEAL JOINTSTOP requires a 50mm minimum clear coverage from the face of the concrete.

SWELLSEAL JOINTSTOP is used primarily for foundation walls / slab joints, slab-ongrade, precast wall panels, manholes, pipe connections, box culverts, wet wells, and potable water tanks.

PHYSICAL PROPERTIES Physical Properties

Installation Guide The waterstop may be installed either into a groove cast in the concrete or directly onto the concrete surface. Full application instructions, including the use of the ancillary products, are contained in a separate application leaflet which is available on request.

Hydrophilic Butyl Bentonite

• Easy to install by bonding, nailing or casting into joint face.

• Factory made connectors enable full integration of swellable and exciting waterstop networks.

• Swelling properties uneffected by long term wet/dry cycling.

• Sustains effective seal in wet conditions.

JOINTSTOP (BN)

JOINTSTOP (BN)

Hydrophilic Butyl Bentonite

Benefits

Hydrophilic Butyl Bentonite

USES A flexible butyl rubber and bentonite compound that swells upon contact with water to form a long-lasting compression seal in non-moving concrete joints. SWELLSEAL JOINTSTOP requires a 50 mm minimum clear â&#x201E;˘ coverage from the face of the concrete.

SWELLSEAL JOINTSTOP is used primarily for foundation walls / slab joints, slabs-ongrade, precast wall panels, manholes, pipe connections, box culverts, wet wells, and potable water tanks.

INSTALLATION JOINTSTOP (BN) SWELLSEAL The waterstop may be installed either into a groove cast in the concrete or directly onto the concrete surface.

Full application instructions, including the use of the ancillary products, are contained in a separate Installation Guide (continued) application leaflet which is available on request.

TM

SWELLING CHART & INSTALLATION HEALTH & SAFETY

SHELF LIFE Minimum of 12 months when stored under recommended conditions.

Technical Service

PHYSICAL PROPERTIES

The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

Health and Safety Before using or handling material, please refer to the Material safety Data Sheet (MSDS).

Storage and Shelf Life Must be stored in a cool dry place.

Minimum of 12 months when stored under recommended conditions.

Statement Of Responsibility The technical information contained in this document is based on current practical knowledge. As this information is of a general nature, no assumptions can be made that it will be suitable for any application and any warranties will be issued on a project by project basis. It is the contractorâ&#x20AC;&#x2122;s responsibility to ensure that the procedures are carried out.

JOINTSTOP (BN)

Must be stored in a cool dry place.

Hydrophilic Butyl Bentonite

STORAGE

Hydrophilic Butyl Bentonite

Before using or handling material, please refer to the Material safety Data Sheet (MSDS).

STOP (BN)

JOINTSTOP (BN)

Swelling Chart - SwellSeal Jointstop (BN)

™

SWELLSEAL JOINTSTOP (HR) HYDROPHILIC RUBBER Product Description SwellSeal Jointstop HR is made of high performance modified rubber.

The swelling action is the result between water and hydrophilic groups which are part of the TM molecular structure.

Expansion of the waterstop creates a positive seal against the face of the concrete joint and prevents the water entry into the structure through the protected joint.

Uses Hydrophilic Waterstop can be applied against existing concrete and are simply installed by SWELLING CHART & INSTALLATION nailing or using a hydrophilic adhesive. In contact with water, hydrophilic strips react and swell by up to 300% of their original dimensions to form a compression seal.

Hydrophilic strips are suitable for installation in low movement construction slabs.

SWELLSEAL JOINTSTOP HR is used primarily for foundation walls / slab joints, slabs-ongrade, precast wall panels, manholes, pipe connections, box culverts, wet wells, and potable water tanks.

• Simple application and joining techniques • Slow expansion rate to prevent damage to freshly placed concrete during curing • Retains original shape after repeated swelling and contraction • Swelling properties unaffected by long term wet/dry cycling • Sustains effective seal in wet conditions • Able to withstand wet conditions prior to concrete pour

Hydrophilic Rubber

PHYSICAL PROPERTIES Physical Properties

INSTALLATION Installation Guide Where thesubstrate substrate uneven, SwellSeal JOINTSTOP Jointstop HRcan can fastened in place using Where the is is uneven, SWELLSEAL bebe fastened in place using masonry nails at masonry nails at approx.

300mm should be taken to ensure that the approx. 300mm centres.

Care shouldcentres. be takenCare however to ensure that however the substrate has sufficient strength to enable a mechanical fixingstrength to be securely drivena without damaging thetoSWELLSEAL substrate has sufficient to enable mechanical fixing be securelyJOINTSTOP. driven without Alternatively, groove canJointstop be cast into danaging thea SwellSeal HR.concrete to facilitate application.

Alternatively, a groove can be cast for into conrete fascilitate application.

SWELLSEAL JOINTSTOP is suitable use in mostto weather conditions, but heavy rain or prolonged immersion will cause premature swelling.

Should this occur, it will be necessary to allow it to dry out, or be dried with a hot air gun before concrete pouring takes place.

(HR)

JOINTSOP (HR)

Hydrophilic Rubber

Benefits

™

SWELLSEAL JOINTSTOP (HR) Installation Guide (continued) SwellSeal Jointstop HR is suitable for use in moist weather conditions, but heavy rain or TM prolonged immersion will cause premature swelling.

Should this occur, it will be necessary to allow it to dry out, or be dried out with a hot air gun before concrete pouring takes place.

SwellSeal Jointstop SS2010 and SwellSeal Jointstop SS2010N should not be used in expansion joints or any concrete section of less than 150mm width.

Technical Service PHYSICAL PROPERTIES

Packaging • HR-2003 - 20mm x 3mm x 30m roll (10x rolls/box) • HR-2004 - 20mm x 4mm x 25m roll (10x rolls/box) • HR-2005 - 20mm x 5mm x 20m roll (10x rolls/box) • HR-2010, (N) - 20mm x 10mm x 10m roll (10x rolls/box) • (N) option: - centre stainless steel net insert.

Health and Safety Before using or handling material, please refer to the Material safety Data Sheet (MSDS).

Storage and Shelf Life

Hydrophilic Rubber

The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

Hydrophilic Rubber

SWELLING CHART & INSTALLATION Swelling Chart - SwellSeal Jointstop HR

Minimum of 12 months when stored under recommended conditions.

Where the substrate is uneven, SWELLSEAL JOINTSTOP can be fastened in place using masonry nails at approx. 300mm centres. Care should be taken however to ensure that the substrate has sufficient strength to enable a mechanical fixing to be securely driven without damaging the SWELLSEAL JOINTSTOP.

The technical information intothis document is based Alternatively, a groove can be castcontained into concrete facilitate application.

on current practical knowledge.

As this information is of a general nature, no assumptions can be made that it SWELLSEAL JOINTSTOP is suitable for use in most weather conditions, but heavy rain or prolonged immersion will cause premature swelling. will be suitable for any application and any warranties will be issued on a project by project Should will be necessary to allow it to dry or be that dried the with procedures a hot air gun before concreteout. basis.this It isoccur, the itcontractor’s responsibility to out, ensure are carried pouring takes place.

SWELLSEAL STOP SS2010 and SWELLSEAL JOINTSTOP SS2010N should not be used in expansion joints or any concrete section of less than 150mm width.

JOINTSTOP (HR)

Statement Of Responsibility

JOINTSOP (HR)

Must be stored in a cool dry place.

INSTALLATION

INJECT RE-INJECTABLE HOSE INSTALLATION SYSTEM Product Description

Re-Injectable Hose Installation System

X-SEAL INJECT is a re-injectable hose system for installation into cold joints under the water table to waterproof and then provide a constant portal into the cold joint to re-inject if required.

The hose is resilient, water proof and not affected by low temperatures and is chemically inert. The main feature of the X-SEAL INJECT is an injection channel, which is a solid hose core made of high quality PVC. The core is capable of absorbing concrete pressure, ensuring the integrity of the injection channel. Laterally staggered injection openings ensure a uniform discharge of the injection material. Compressible neoprene strips in the longitudinal grooves are a unique and extremely important element of the X-SEAL INJECT Hose System. These strips act as valves during injection and as a seal while cleaning the tube for reinjection.

(A) Concrete Pour

(B) Injection

When the concrete is placed around the X-SEAL INJECT Hose, the external pressure of the concrete seats the neoprene strips, sealing off injection openings and the injection channel.

The internal injection pressure compresses the neoprene strips and allows the injection material to flow out from eight longitudinal gaps. This enables a uniform discharge of the injection material over the full length of the hose.

(A)

(B)

(C)

(D)

(C) Cleaning the Hose

(D) Ready for Future Injection

When using an approved injection material, the X-SEAL INJECT Hose is easily flushed clean by using water and applying vacuum pressure. The negative pressure reseats the neoprene strips, preventing injected material from being drawn back into the injection channel upon cleaning.

X-SEAL INJECT Injection System is ready for reinjection if needed.

Uses

X-SEAL INJECT

X-SEAL INJECT can be used in all construction joints under the water table such as basements, tunnels, dams, lift wells, reservoirs, sewerage plants, poured pilings, bridge connections or anywhere where a cold concrete joint is susceptible to leaks in the presence of water.

Benefits

• The hose is completely re-injectable so it can be used over and over if leakage persists or is caused by building movement or some other event.

• The hose is flexible to follow the contours of the joint and follow corners without cutting or joining.

• The unique 900 connection valve allows easy, efficient and secure fastening to the delivery hoses which eliminates messy shrink tape which is often prone to failure.

Installation Guide Fabrication - Placers must be provide proof of full training by NEOFERMA prior to accepting a job and the X-SEAL INJECT Instruction manual should be rigorously followed to ensure success.

X-SEAL INJECT is simply taped and cut into maximum 10 metre lengths. The unique right angle connection valve is inserted into the hose and the delivery hoses using a construction adhesive. The delivery hoses are colour coded to identify inlet and outlet during injection.

INJECT Installation Guide (continued) Placement The surface of the joint should be clean and free of any surface irregularities. The hose should be installed into the cold joint in approximately the centre of the joint (for thicker sections place the hose approximately 200mm from the water side of the joint).

Place a line of SWELLSEAL JOINTSTOP BR in the cold joint approximately 80mm from water side of the joint to prevent loss of the injection material. Fasten the hose to the concrete using the clips provided. Centre and spread the clips approximately 250mm apart over the length of the hose. (Do not fasten the hose to reinforcing steel) Ensure that the delivery hoses terminate outside of the structure to allow future access. At least a metre long length of delivery hose is required outside the joint to enable easy access to pump. At each intersection, do not cross the injection hoses always cross with a delivery hose and keep the injection hoses at least 50mm from each other. NEOFERMA recommends that the ends of the delivery hoses be housed in a junction box to protect them from damage and that the delivery hose end plugs be securely in place.

X-SEAL INJECT should only be injected with X-SEAL INJECTION RESIN and all or any warranties are negated with the use of other products. The minimum time before injection after the concrete is poured is 28 days to ensure that the concrete has reached full strength. Pump using a parastaltic pump which is capable of vacuuming. Always start at one end of the hose with the following procedure; (1) Connect the pump hose to the X-SEAL INJECT delivery hose.

(2) Station assistant at the other end of the hose armed with multigrips to close off the hose and a bucket.

(3) Fill the hose with X-SEAL INJECTION RESIN by means of the pump until it comes out the other end of the hose. Close the end of the hose with the multigrips and pressurise the X-SEAL INJECT hose between 5-7 bar.

(4) From the moment that no material flows into the joint and no, or only a slight pressure drop is visible on the gauge, keep the pressure for approximately 5 minutes at 5-7 bar. This is essential to allow the injection material to penetrate into the joint. Sealing is a matter of moderate pressure and longer injection time, and not high pressure and short injection time.

(5) Apply the same procedure as before from the other end of the SWELLSEAL INJECT Hose.

This is to make sure that there is similar distribution pressure.

Re-Injectable Hose Installation System

Injection -

Reverse the parastaltic pump and install the pressure equaliser valve. Immerse the other end in a bucket of water. Vacuum until water runs clear through the pipe. Repeat this procedure from the other end. Plug ends and store in junction box.

Technical Service The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

Storage and Shelf Life Must be stored in a cool dry place. The product has a minimum shelf life of 12 months when stored under recommended conditions.

Health and Safety For workplace health and safety hazard information please consult the NEOFERMA MSDS available at www.neoferma.com/msds

X-SEAL INJECT

Cleaning For Future Re-Injection-

SWELLSEAL JOINTSTOP DPS-500 LIQUID HYDROPHILIC PU WATER-STOP FOR SHEET PILE INTERLOCKS Product Description SWELLSEAL JOINTSTOP DPS-500 is a liquid hydrophilic Polyurethane waterstop for sheet pile interlocks.

The hydrophilic properties of SWELLSEAL JOINTSTOP DPS-500; • Good consistency in swell rate during repeated wet/dry cycling.

• Expansion of the product on contact with water creates a positive pressure against

the faces of the conrete joint, thus preventing the passage of water.

One Component Hydrophilic Polyurethane

Benefits • Actively deals with deformation of the sheet piles, due to its elasticity.

• Ease of application, one component brush or spray.

• Excellent adhesion to clean surfaces.

• Apply in all weather conditions.

• Prolonged life expectancy, retains its original form even with repeated expansion.

Physical Properties Appearance: Viscosity: Solid Content (%): Solvent composition: Physical Properties: Tensile Strength (kgf/cm2): Elongation (%): Curing Time: Swelling Ratio (%):

Light-Yellowish transparent liquid 5,000 +_ 2,000 cPS/250C 85 +_ 2 Xylene, Ethyl Acetate > 10 over 450% inner 24hrs (RT, 750 -’RH) > 400% - ‘(Immersion for 48 hrs in water at room temperature)

Technical Service The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

JOINTSTOP DPS-500

Packaging • 18Kg Can

Storage and Shelf Life SWELL JOINTSTOP DPS-200 must be stored in a cool dry place for up to 6 months at below 250C. Avoid exposure to humidity or temperatures above 500C for extended time.

The product is very sensitive to air, once opened the product will detoriate.

Health and Safety Before using or handling material, please refer to the Material safety Data Sheet (MSDS).

SWELL JOINTSTOP DPS-200 may cause irritation if it comes into direct contact with the skin.

Avoid contact with skin and eyes.

Wear suitable gloves and eye/face protection.

Use only in well ventilated areas.

SWELLSEAL JOINTSTOP DPS-500 Statement Of Responsibility

JOINTSTOP DPS-500

One Component Hydrophilic Polyurethane

The technical information contained in this document is based on current practical knowledge. As this information is of a general nature, no assumptions can be made that it will be suitable for any application and any warranties will be issued on a project by project basis. It is the contractorâ&#x20AC;&#x2122;s responsibility to ensure that the procedures are carried out.

TM

SWELLSEAL JOINTSTOP (DS) DUAL SYSTEM: PVC WATERSTOP WITH HYDROPHILIC SWELLSEAL JOINTSTOP DS RUBBER INLAYS Product Description DESCRIPTION

Co-extruded to prevent damage on site

USES

Hydrophilic Rubber

Uses

Jointstop DS Waterstops are designed to protect structures where movement and construction joints cast in-situ occur. These can be WATER RETAINING such as tanks; sewerage plants; dams, canals and waterways, JOINTSTOP DS waterstops is designed to protect structures where controlled movement, swimming pools and balance tanks.

cast in-situ construction joints occur. These can be water retaining structures such as Any areas that require containment and bunds. tanks, sewerage plants, dams, canals, waterways and swimming pools. Water excluding WATER EXCLUDING constructions such as basements below ground, underground carparks; tunnels and constructions, such asroof basements ground, underground car parks, tunnels, retaining stations. Retaining walls; decks andbelow podiums. walls, and concrete decks.

PVC + Hydrophilic Rubber

Dual System: PVC waterstop with Hydrophilic Rubber Inlays

This system enables PVC the PVC Waterstop towith be fixed on site in the in the usualInlays way but provides Dual System: waterstop Hydrophilic Rubber a dual system designed to combine the latest developments in hydrophilic technology with This new system enables the PVC waterstop to be fixed on site in the in the normal way but provides a dual system the proven benefitstheoflatest PVC.developments Swellseal JOINSTOP DStechnology conformswith to the proven benefits of PVC. designed to combine in hydrophilic AS 4020 and is suitable for use when in contact with potable water and can beand used SWELLSEAL JOINTSTOP DS WATERSTOP is suitable for use in contact with potable water canin be used situations where salt water, sewage are prevalent. situations where salt and contaminated water is prevelent.

ADVANTAGES

Benefits For use in extreme environments such as salt water and sewerage.

• Jointstop DS is unique as it can be manufactured to project specific applications and is Range of profiles that can be adapted to site requirements.

Simple onforsiteuse in extreme environments such as high salt water, sewerage and contaminated welding or sleeve methods, that requires no heat.

Conformswater. with AS 4020 • Hydrophilic components can be retarded or advanced according to site conditions.

• Jointstop DS is manufactured from a combination of PVC and Hydrophilic rubber with HEALTH & SAFETY Before using a range of profiles that can refer be adapted to site requirements. or handling material, please to the Material Safety Data Sheet (MSDS).-----• Simple on site welding or sleeve methods, that require no heat.

STORAGE

Physical Properties Must be stored in a cool dry place.

Protect hydrophilic rubber parts from rainwater or ponding water.

Test Item

SHELF-LIFE

Hardness (Hs):

PVC Plate

Hydrophilic Rubber

Test Method

65

Minimum of 12 months when stored under recommended

Tensile Strength (kg f/cm2):

120

Elongation (%):

250

Expansion Volume (%):

KS M 3805

100 above

KS M 6518

JOINTSTOP (DS)

JOINTSTOP (DS)

Combination of PVC &Hydrophilic Rubber.

TM

SWELLSEAL JOINTSTOP DS Installation Guide INSTALLATION

• Avoid dust, oil & lubricant before installation.

Avoid dust, oil & lubricant before use.

• Protect hydrophilic rubber parts from ponding.(A delay swell coating can be provided Complex waterstop should be fixed in right place during concreting.

Protect hydrophilic if required) rubber parts from rainwater or ponding water.

• excessive Protect JOINTSTOP DS from concrete Do use force on hydrophilic rubber areas.overspill and damage, keep plastic cover in

place until required completion

PHYSICAL PROPERTIES • Do not use excessive force on hydrophilic areas during installation.

Dual System: PVC waterstop with Hydrophilic Rubber Inlays

PVC + Hydrophilic Rubber

Waterstops must be installed so that they are secure in their correct position when the Waterstops must be installed so that they are secure in their correct position when the concrete is being concrete placed. is placed. When reinforcement is present, an adequate clearance must be provided to allow correct compaction.

Concrete must be fullymust compacted around thecompaction. waterstop to Where reinforcement is present, and adequate clearance be provided to allow eliminate voids or porous areas.

For detailed or project specific installation instruction please Concrete must be fully compacted around the waterstops to eliminate voids or porous areas. contact your Neoferma Technical Representative.

For detailed installation instructions please contact your Neoferma Technical Representative for specific product applications.

Note: Installation may require on site jointing, be achieved by either heat iron by or sleeve welding • Installation may require on this sitecan joining which can be achieved welding or methods, on request. further information joint sleeving.

Further information can be provided on request.

Technical Service

Storage and Shelf Life Must be stored in a cool dry place. Protect hydrophilic rubber parts from rainwater or ponding water. The product has a minimum shelf life of 12 months when stored under recommended conditions.

Health and Safety Before using or handling material, please refer to the Material Safety Data Sheet (MSDS) available at www.neoferma.com/msds

Statement Of Responsibility The technical information contained in this document is based on current practical knowledge. As this information is of a general nature, no assumptions can be made that it will be suitable for any application and any warranties will be issued on a project by project basis. It is the contractor’s responsibility to ensure that the procedures are carried out.

JOINTSTOP (DS)

JOINTSTOP (DS)

The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

X-SEAL Hydrophilic Rubber Waterstop for Expansion Joints

DESCRIPTION

SEAL

X-SEAL is a high performance hydrophilic rubber waterstop designed for use in concrete expansion joints. Upon contact with moisture, the X-SEAL will expand to over 150% of its original size to form a compression seal across the face of the joint and thus prevent water entry into the structure through the protected joint.

HYDROPHILIC RUBBER WATERSTOP FOR EXPANSION JOINTS X-SEAL is embedded with a stainless steel wire mesh to ensure the waterstop remains in firmly in place when secured to the substrate with nails / screws. The mesh also maintains the integral strength of the rubber through repeated long term wet /dry cycles.

ProductJoints Description ubber Waterstop for Expansion

X-SEAL is a high performance hydrophilic rubber waterstop designed for use in concrete expansion joints. Upon contact with moisture, the X-SEAL will expand to over 150% of its original size to form a compression seal across the face of the joint and thus prevent water entry into the structure through the protected joint. hydrophilic rubber waterstop designed for use in concrete expansion joints. Upon EAL will expand to over 150% of its original size to form a with compression seal across the wire mesh to ensure the waterstop remains firmly X-SEAL is embedded a stainless steel ent water entry into the structure through the protected joint. in place when secured to the substrate with nails / screws. The mesh also maintains the ainless steel wire mesh to ensure the waterstop remains in firmly in place when strength of theofrubber through nails / screws. The mesh alsointegral maintains the integral strength the rubber through repeated long term wet/dry cycles.

cles.

USES X-SEAL is used in expansion joints. This product is an excellent waterstop for use in movement joints.

oints. This product is an movement joints.

is from the surface of the g nails or swellable mastic. h both sides of the joint.

Y

HEALTH & SAFETY X-SEALBefore is used inorexpansion joints. using handling material, please refer to the Material Safety Data Sheet (MSDS).

This product is an excellent waterstop for use in movement joints.

STORAGE Must be stored in a cool dry place.

SHELF LIFE

Minimum of 12 months when stored under recommended conditions.

rial, please refer to

t (MSDS).

Physical Properties

ace.

Test Item

X-SEAL

stored under recommended

Waterstop for Expansion Joints

Waterstop For Expansion Joints

Uses

Remove any dirt or loose debris from the surface of the concrete. Adhere X-SEAL using nails or swellable mastic.

X-SEAL must be in contact with both sides of the joint.

Result

Color: Black Hardness (HS)

45 _+ 10

Tensile Strength

> 25Kg/cm

Elongation

> 550%

Expansion Volume

> 150%

Specify Gravity

> 1.1

Vulcanization

Yes

2

Test Method ASTM D240 ASTM D412 ASTM D412 ASTM D792

Installation Guide Remove any dirt or loose debris from the surface of the concrete. Adhere X-SEAL using nails or swellable mastic. X-SEAL must be in contact with both sides of the seal.

Waterstop for Expansion Joints

INSTALLATION

Technical Service The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

Packaging â&#x20AC;˘ 30mm x 30mm x 10m per roll (2x rolls per box)

Storage and Shelf Life Must be stored in a cool dry place.

Health and Safety For workplace health and safety hazard information please consult the NEOFERMA MSDS available at www.neoferma.com/msds

Statement Of Responsibility

X-SEAL

Waterstop For Expansion Joints

The technical information contained in this document is based on current practical knowledge. As this information is of a general nature, no assumptions can be made that it will be suitable for any application and any warranties will be issued on a project by project basis. It is the contractorâ&#x20AC;&#x2122;s responsibility to ensure that the procedures are carried out.

REMEDIAL WORKS X-Gel is a hydrophilic urethane crack injection system designed to seal leaking cracks, joints and holes in concrete such as basement slabs and walls. In this application water curing hydrophobic sealant is injected, under pressure, into the crack or joint. The injection can be effected from inside or outside the structure and with minimal disruption. Further, the work can be performed on actively leaking cracks. When cured, the urethane forms a tough, flexible seal that prevents water ingress.

Westox Cocoon ÂŽ The Cocoon Desalination System is designed to extract salts from concrete structures and masonry. It is applied after the salt analysis of the structure. The salts are then extracted by means of a poultice.

Re-construction of Joints We developed NeoJoint to facilitate the repair and sealing of expansion joints in major concrete structure such as car parks, dams, and podiums. The existing joint is rebuilt using high strength repair mortar and the Neoferma gasket.

www.neoferma.com

HERITAGE RESTORATION PRODUCTS

Neoferma Australia are proud to be the exclusive distributors of Westox Cocoon.

Westox a member of the Australian Heritage Council has a large range of unique heritage restoration products including Cocoon, a superior product specifically designed to extract salts from buildings to aid the restoration process and has restored some of the most wellknown heritage buildings globally.

GLOBAL RESTORATIONS WITH COCOON: Past projects

• • • • • • • • •

Petra, Jordan, Dept. of Antiquaries Jordan Baptism Site “Bethany Beyond the Jordan” (Al-Maghtas) DOA Jordan The Duomo, Pisa, Italy St Marks Basilica, Venice, Italy Palazza Minotto, Venice, Italy The Glasmuseum, Quedlinburg, Germany Castle and Schloss Sanssouci, Potsdam, Germany The World Heritage Site, Georgetown Penang, Malaysia The Governor’s Mansion, Suffolk House and the Old Court House, Penang

Malaysia • • • • •

Fort Denison and St Mary’s Cathedral, Sydney Australia The Walter Reid Façade Repairs, Rockhampton Australia The Moreton Club, Brisbane, Australia The National Trust Head Office, Brisbane Australia The Thomas Dixon Arts Centre, Brisbane , Dept of Public Works. Australia

Cocoon has been extensively tested with the University of Florence, the University of Venice, Edilvenezia Venice, and the Instituto Per La Conservazione E La Valorizzazione Dei Beni Culturali (ICVBC) Florence, Italy.

Westox continue to develop and refine products and systems for the conservation of heritage artifacts, and look forward to being able to pass on knowledge and contribute to the preservation of heritage landmarks throughout the world.

St. Apollonia

St. Apollonia was originally the monastery for St. Marks Basilica. Now being used as a museum for religious art works. (Museo Diocesano di Arte Sacra). Cocoon was used to remove salts from the 60cm thick walls over a two year period utilising the active rising damp to flush out the salts before installing a chemical damp proof course. An estimated 9kg of salt was removed from each square metre of wall area over the two year period.

www.neoferma.com

ST. APOLLONIA St. Apollonia was originally the monastery for St. Marks Basilica. Now being used as a museum for religious art works. (Museo Diocesano di Arte Sacra). Cocoon was used to remove salts from the 60 cm thick walls over a two year period. An estimated 9 kg of salt was removed from each square metre of wall area over the two year period.

COCOON Westox Cocoon poultice is one of its kind in the world! It was designed by Westox, who recognised the need for a product to remove salt from masonry of all types, concrete, brick or sandstone. It is a poultice that is capable of drawing salt out of masonry and halting deterioration, manufactured from pharmaceutical grade filter paper and features a very high internal surface area with high porosity and purity.

The ancient monument of Petra, Jordan is amongst many world famous buildings benefiting from Cocoons unique properties. From Concrete to Sandstone if it has salts Cocoon will remove them.

www.neoferma.com

COCOON Desalination Process

Stage 1 - Salt saturated sub soil

Stage 2 - Salt migration from sub soil to bottom section of slab

Stage 3 - Salt migration continues.

Partial slab penetration.

Stage 4 - Salt migration. Full slab penetration. All reinforcing steel encapsulated. Salt exposure on slab surface and column base.

Stage 5 - Salt migration. Full slab penetration.

All reinforcing steel encapsulated.

Salt exposure on slab surface and salt migration up column.

Legal Disclaimer: Neoferma Australia and itsâ&#x20AC;&#x2122; associated companies are not Engineers. These drawings are for system illustration only and not intended as the approved design or for any other purpose.

Each drawing must be submitted to the Project Engineers for their consideration and if approved incorporated by them into the relevant details. Neoferma Australia does not accept any liability/ responsibility to any third party who may suffer or damage as a result of the use or reliance upon the whole or any part of the drawings.

www.neoferma.com

COCOON Desalination Process

Stage 5a - 1st Application of Westox Cocoon.

Stage 6 - Westox Cocoon starting to draw salt from the concrete.

Stage 7 - 1st coating of Cocoon has been removed taking some of the salts with it.

2nd Salt test undertaken at this point.

Stage 8 - 2nd Application of Westox Cocoon starts to draw remaining salts into the coating

Stage 9 - Desalination Complete. A final salt test is required on completion.

Salt testing and analyse recommended every 24 months.

Legal Disclaimer: Neoferma Australia and itsâ&#x20AC;&#x2122; associated companies are not Engineers. These drawings are for system illustration only and not intended as the approved design or for any other purpose.

Each drawing must be submitted to the Project Engineers for their consideration and if approved incorporated by them into the relevant details. Neoferma Australia does not accept any liability/ responsibility to any third party who may suffer or damage as a result of the use or reliance upon the whole or any part of the drawings.

www.neoferma.com

SEALTAQ® AQUABLOCK SWELLABLE SEALING COMPOUND Product Description SEALTAQ AQUABLOCK suited for sealing wall, pipe or cable inlets, joints and hollow spaces against gases, moisture, standing water and running groundwater leaks. SEALTAQ is the brand for the professional construction market for civil application. SEALTAQ material comes in cartridges, sausages, pails or membrane-rolls for applications such as:

SEALTAQ Aquablock

Visco-Elastic Sealants & Swellable Aquablock Systems

Uses • • • • • • • •

Wall inlets below groundwater level Wall penetrations inside buildings Multi-pipe & cable inlets Leaking expension joints Roofs Basement membrane Sealing Windows Concrete-, wooden- or tile floors

Benefits SEALTAQ AQUABLOCK provides safe, fast and secure protection for any kind of civil application to offer 100% waterproofing and airtightness.

• Requires minimal surface preparation • The sealing remains flexible • Adheres to wet and dry surfaces • Does not require special application tools • Fast & easy to apply • No material waste; paste re-usable • Long pot-life, does not become hard • Immediate sealing: no curing time needed • Can resist up to 0.3 bar of groundwater pressure • Provides permanent and optimal safety • • Water and gas impermeable • No fumes, no chemical reactions • Non-toxic - applicator and environment friendly • Adjusts to movements of pipes & cables • Does not age • Allows adding and removing of conduits at any time • Service temperature -20°C to +50°C

Physical Properties Service temperature -20°C to +50°C

Installation Guide

Technical Service The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

Packaging • cartridges, • sausages, • pails,

Visco-Elastic Sealants & Swellable Aquablock Systems

Remove any dirt or loose debris from the surface.

Must be stored in a cool dry place.

• Long pot-life, does not become hard • Does not age

Health and Safety For workplace health and safety hazard information please consult the NEOFERMA MSDS available at www.neoferma.com/msds

Statement Of Responsibility The technical information contained in this document is based on current practical knowledge. As this information is of a general nature, no assumptions can be made that it will be suitable for any application and any warranties will be issued on a project by project basis. It is the contractor’s responsibility to ensure that the procedures are carried out.

SEALTAQ Aquablock

Storage and Shelf Life

SEALTAQ® VISCO-ELASTIC UNIVERSAL SEALANT BAND Product Description SEALTAQ UNIVERSAL BAND is impermeable once applied. It adheres to plywood, concrete, tiles, brick, natural stone, steel, glass and stics. Any seam can be sealed easily, even at very low temperatures. The Sealtaq Universal or Roofingband can be overcoated by any kind of flexible elastomeric coatings such as polyurea, polyurethane and hybrids, or as underground for tile adhesives/plasters.:

SEALTAQ Aquaband

Visco-Elastic Sealants & Swellable Aquablock Systems

Uses • • • • • • • •

Wall inlets below groundwater level Wall penetrations inside buildings Multi-pipe & cable inlets Leaking expension joints Roofs Basement membrane Sealing Windows Concrete-, wooden- or tile floors

Benefits SEALTAQ UNIVERSAL BAND provides safe, fast and secure protection for any kind of civil application to offer 100% waterproofing and airtightness.

• Requires minimal surface preparation • The sealing remains flexible • Adheres to wet and dry surfaces • Does not require special application tools • Fast & easy to apply • No material waste; paste re-usable • Long pot-life, does not become hard • Immediate sealing: no curing time needed • Can resist up to 0.3 bar of groundwater pressure • Provides permanent and optimal safety • • Water and gas impermeable • No fumes, no chemical reactions • Non-toxic - applicator and environment friendly • Adjusts to movements of pipes & cables • Does not age • Allows adding and removing of conduits at any time • Service temperature -20°C to +50°C

Physical Properties Service temperature -20°C to +50°C

Installation Guide Remove any dirt or loose debris from the surface before application.

Packaging • 10m Rolls (100mm wide)

Storage and Shelf Life Must be stored in a cool dry place.

• Does not age

Health and Safety For workplace health and safety hazard information please consult the NEOFERMA MSDS available at www.neoferma.com/msds

Statement Of Responsibility The technical information contained in this document is based on current practical knowledge. As this information is of a general nature, no assumptions can be made that it will be suitable for any application and any warranties will be issued on a project by project basis. It is the contractor’s responsibility to ensure that the procedures are carried out.

SEALTAQ Aquaband

The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

Visco-Elastic Sealants & Swellable Aquablock Systems

Technical Service

1000 HYDROPHOBIC WATERSTOP RESIN Product Description X-GEL 1000 is a hydrophobic, two part, semi-rigid foam type water containing agent that is manufactured for applications to the water leaking cracks or to areas of relatively high water pressure. Reaction Speed can be tailored to the condition with the catalyst, initial foaming starts in a minimum of 15sec.

Uses X-GEL 1000 is mainly used to stop flows of running water instantaneously in the civil construction site or underground structures etc.

Benefits • X- GEL 3000 reacts even with a small amount of water.

• Rapid expansion.

Mixing Ratio effect-

Hydrophobic foam-type Waterstop resin

Physical Properties

Technical Service

Packaging • 18.2 Kg container • 1.8 Kg (Catalyst)

Health and Safety This product is safe to use. It is prudent however, to observe care, follow industrial hygiene practices and wear protective clothing gloves and goggles. Avoid contact with skin and eyes.

Should this occur flush the contacted areas thoroughly for at least 15 minutes with clean water. Do not consume (eat or drink) the product. If the product is consumed DO NOT induce vomiting, drink a lot of water and consult with a doctor immediately or ontact the Poisoning Information Centre. (Australia 131126 – New Zealand 0800764766) for first aid advice. Avoid breathing vapours. For workplace health and safety hazard information please consult the NEOFERMA MSDS available at www.neoferma.com/msds

X-GEL 1000

The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

2000 LIQUID POLYURETHANE WATERSTOP Product Description X-GEL 2000 is a liquefied Half-hard type Polyurethane water leakage construction product and is a dark-brown transparent liquid in appearance.

Uses X-GEL 2000 is used for all concrete constructions where leaks are occuring through joints or cracks, such as: basement parking lots, filtration plants, water storage tanks, final sewage disposal plant, wall picks, pipeline connection, roof to roof joints,

Benefits • Single component - easy to use.

• High elasticity - able to move in expansion joints.

Liquid Polyurethane Waterstop

Physical Properties Viscosity (mPa.s 25°) Gravity (25°) Elasticity (MPa) Elongation (%) Expansion Rate Foaming time Foaming magnification

130 -150 1.20 - 1.30 > 4.6 20% 25 X 330 sec (measured temp: 23 ± 20C) 25 X (medicinal liquid: water= 10 : 1)

Mixing Ratio 1 liquid type

Installation Guide Examine Crack Status After complete examination of the thickness of the structure, depth and width of the cracks or joints, secure the area and mask off any areas which may be adversely affected by over spill.

X-GEL 2000

Prepare Surface of the Crack Clean the area of the crack or joint using a brush, wire brush or compressed air (remove any oil, stains or contamination with thinners etc.) and remove any dust or debris from the crack or joint.

Insert Packer Clean any dust from the crack or joint and insert a NEOFERMA brass packer into the hole and tighten to secure.

Injection Inject X-GEL 2000 into the crack or joint through the packer at regular intervalls until the leakage has stopped and the solution has reacted and is visibly coming out of the crack or joint.

Remove Packer Remove head part of the packer protruding from the surface and grind flush.

Finishing Seal the area with an epoxy sealer or cementitious repair mortar.

2000 Installation Guide (continued) This must be carried out by a trained technician, the medical liquid poured from the original container into the container with grouting injection pump.

X-Gel 2000 liquid, catalyst is already added, in low temperature applications the reaction time needs to be increased on the spot for coping with large volumes of water add extra foaming agent (X-Gel 2000CAT) see technical guideleines for ratios.)

Technical Service The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

Packaging • 10 Kg/PE container • 20 Kg

Storage and Shelf Life

Health and Safety This product is safe to use. It is prudent however, to observe care, follow industrial hygiene practices and wear protective clothing gloves and goggles. Avoid contact with skin and eyes.

Should this occur flush the contacted areas thoroughly for at least 15 minutes with clean water. Do not consume (eat or drink) the product. If the product is consumed DO NOT induce vomiting, drink a lot of water and consult with a doctor immediately or ontact the Poisoning Information Centre. (Australia 131126 – New Zealand 0800764766) for first aid advice. Avoid breathing vapours. For workplace health and safety hazard information please consult the NEOFERMA MSDS available at www.neoferma.com/msds

Statement Of Responsibility

Liquid Polyurethane Waterstop

Must be stored in a cool dry place. The product has a minimum shelf life of 6 months when stored under recommended conditions.

X-GEL 2000

The technical information contained in this document is based on current practical knowledge. As this information is of a general nature, no assumptions can be made that it will be suitable for any application and any warranties will be issued on a project by project basis. It is the contractor’s responsibility to ensure that the procedures are carried out according to the Neoferma X-GEL Instruction Manual.

HYDROPHILIC POLYURETHANE WATERSTOP Product Description X-GEL 3000 is a hydrophilic polyurethane waterstop that is highly effective for the treatment of leakage in concrete structures. X-GEL 3000 has an expansion rate of 700 – 800% when in contact with water and forms a high density cell structure which makes it effective in flowing water.

Uses X-GEL 3000 is effective for defective and honeycombed concrete, sealing cracks and joints, sealing structural cracks subject to movement, waste water tanks, sewer/manholes, tunnels, dams and service penetrations.

Hydrophilic Polyurethane Waterstop

Benefits • X- GEL 3000 reacts even with a small amount of water.

• Single component - easy to use.

• Rapid expansion (including in fresh or salt water).

• High elasticity - able to move in expansion joints.

• Ultra low viscosity – will enter the smallest of cracks.

• High adhesion to wet surfaces – can be injected into flowing water.

Physical Properties Viscosity (mPa.s 25°) Specific gravity (25°) Tensile strength Elongation (%)

3000 ±500 1.1 2.9 96%

Mixing Ratio effect Ratio PU/water 10:5 10:10 10:15 10:20

Start expansion 20 sec 23 sec 25sec 28 sec

Finish expansion 95 sec 110 sec 125 sec 150 sec

Installation Guide

X-GEL 3000

Examine Crack Status After complete examination of the thickness of the structure, depth and width of the cracks or joints, secure the area and mask off any areas which may be adversely affected by over spill.

Prepare Surface of the Crack Clean the area of the crack or joint using a brush, wire brush or compressed air (remove any oil, stains or contamination with thinners etc.) and remove any dust or debris from the crack or joint.

Select Drilling Position According to the amount and condition of leaks mark drilling positions at 12cm to 20cm alternatively on either side of the crack or joint. Drill at an angle of 45° ensuring that the drill passes through the crack or joint.

Expansion rate 1000% 850% 700% 650%

Installation Guide (continued) Insert Packer Clean any dust from the crack or joint and insert a NEOFERMA brass packer into the hole and tighten to secure.

Injection Inject X-GEL 3000 into the crack or joint through the packer until the leakage has stopped and the solution has reacted and is visibly coming out of the crack or joint.

Remove Packer Remove head part of the packer protruding from the surface and grind flush.

Finishing Seal the area with an epoxy sealer or cementitious repair mortar.

Packaging • 20 Kg Pails • 5 Kg Jerry Cans

Storage and Shelf Life Store in cool, dry conditions away from direct sunlight. This product is packed with nitrogen gas so has a maximum shelf life of 6 months if the seal is unbroken.

Once the seal is broken we recommend the product be used as soon as possible.

Health and Safety This product is safe to use. It is prudent however, to observe care, follow industrial hygiene practices and wear protective clothing gloves and goggles. Avoid contact with skin and eyes.

Should this occur flush the contacted areas thoroughly for at least 15 minutes with clean water. Do not consume (eat or drink) the product. If the product is consumed DO NOT induce vomiting, drink a lot of water and consult with a doctor immediately or ontact the Poisoning Information Centre. (Australia 131126 – New Zealand 0800764766) for first aid advice. Avoid breathing vapours. For workplace health and safety hazard information please consult the NEOFERMA MSDS available at www.neoferma.com/msds

Statement Of Responsibility The technical information contained in this document is based on current practical knowledge. As this information is of a general nature, no assumptions can be made that it will be suitable for any application and any warranties will be issued on a project by project basis. It is the contractor’s responsibility to ensure that the procedures are carried out according to the Neoferma X-GEL Instruction Manual.

X-GEL 3000

The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

Hydrophilic Polyurethane Waterstop

Technical Service

HYDROPHOBIC POLYURETHANE WATERSTOP Product Description X-GEL 4000 is a single component hydrophobic polyurethane water stop that is highly effective for the treatment of leakages in concrete structures. X-GEL 4000 has rapid foaming properties and is ideally suited to stop high flowing water leaks in concrete structures.

X-GEL 4000 comes with an optional catalyst to vary the reaction time or compensate for cold conditions.

Uses

Hydrophobic Polyurethane Waterstop

X-GEL 4000 is highly effective for defective and honeycombed concrete, sealing cracks and joints, sealing structural cracks subject to movement, waste water tanks, sewer/manholes, tunnels, dams and service penetrations.

Benefits • X- GEL 4000 reacts with minimal amounts of water.

• X- GEL 4000 has rapid expansion properties (in both fresh or salt water conditions).

• X- GEL 4000 produces a high density closed cell foam structure.

• X- GEL 4000 has a high adhesion to wet surfaces and can be injected into flowing water.

Physical Properties Viscosity (mPa.s 25°) Specific gravity (25°) Tensile strength Elongation (%) Foaming rate

3500 ±500 1.1 0.1 50% >3000%

Reaction Times Temperature0C Foam start (s) Foam ends (s) Foaming (%) Viscosity

5 35 155 3100 900

15 20 120 3400 450

25 15 100 3800 250

Installation Guide

X-GEL 4000

Examine Crack Status After complete examination of the thickness of the structure, depth and width of the cracks or joints, secure the area and mask off any areas which may be adversely affected by over spill.

Prepare Surface of the Crack Clean the area of the crack or joint using a brush, wire brush or compressed air (remove any oil, stains or contamination with thinners etc.) and remove any dust or debris from the crack or joint.

Select Drilling Position According to the amount and condition of leaks, mark drilling positions at 12cm to 20cm alternatively on either side of the crack or joint. Drill at an angle of 45° ensuring that the drill passes through the crack or joint.

30 12 86 4000 205

Installation Guide (continued) Insert Packer Clean any dust from the crack or joint and insert a NEOFERMA brass packer into the hole and tighten to secure.

Injection Inject X-GEL 4000 into the crack or joint through the packer until the leakage has stopped and the solution has reacted and is visibly coming out of the crack or joint.

Remove Packer Remove head part of the packer protruding from the surface and grind flush.

Finishing Seal the area with an epoxy sealer or cementitious repair mortar.

Packaging • 18.2 Kg Pails • 1.8 Kg Pails for optional catalyst

Storage and Shelf Life Store in cool, dry conditions away from direct sunlight. This product is packed with nitrogen gas so has a maximum shelf life of 6 months if the seal is unbroken.

Once the seal is broken we recommend the product be used as soon as possible.

Health and Safety This product is safe to use. It is prudent however to observe care, follow industrial hygiene practices and wear protective clothing gloves and goggles. Avoid contact with skin and eyes.

Should this occur flush the contacted areas thoroughly for at least 15 minutes with clean water. Do not consume (eat or drink) the product. If the product is consumed DO NOT induce vomiting, drink a lot of water and consult with a doctor immediately or ontact the Poisoning Information Centre. (Australia 131126 – New Zealand 0800764766) for first aid advice. Avoid breathing vapours. For workplace health and safety hazard information please consult the NEOFERMA MSDS available at www.neoferma.com/msds

Statement Of Responsibility The technical information contained in this document is based on current practical knowledge. As this information is of a general nature, no assumptions can be made that it will be suitable for any application and any warranties will be issued on a project by project basis. It is the contractor’s responsibility to ensure that the procedures are carried out according to the Neoferma X-GEL Instruction Manual.

X-GEL 4000

The Neoferma International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

Hydrophobic Polyurethane Waterstop

Technical Service

www.neoferma.com

E

X

P

A

N

S

I

O

N

J

O

I

N

T

Expansion Gasket Properties of Neoferma Gasket Description and Application of Neoferma gasket Description and Application of Neoferma gasket The Neoferma gasket is suitable for sealing all types of joints. It is extremely The Neoferma gasket is suitable for sealing all types of joints. It is extremely flexible, consisting of hollow sections terminating in individual lips. flexible, consisting of hollow sections terminating in individual lips.

Neoferma gasket is easily compressed and maintains close contact with concrete, Neoferma gasket is easily compressed and maintains close contact with concrete, steel, glass or wood surfaces. This ensures complete sealing of the joint. steel, glass or wood surfaces. This ensures complete sealing of the joint.

Water Water and and Weather Weather resistance resistance The gaskets have been to a a hydrostatic hydrostatic pressure pressure of of ten ten metres The gaskets have been tested tested successfully successfully to metres and in buildings more thanhigh 100m high with velocity a wind velocity of 160km/hour and in buildings more than 100m with a wind of 160km/hour 2 developing a pressure of 130 kg/m 2 and for buildings 160-320m high with a wind developing a pressure of 130 kg/m and for buildings 160-320m high with a wind pressure of 180 kg/m22. pressure of 180 kg/m .

Sound Sound Insulation Insulation These airborne sound. sound.

These gaskets gaskets exhibit exhibit excellent excellent insulation insulation against against airborne Thermal Insulation Insulation Thermal A single single gasket gasket will will provide provide good good thermal thermal insulation insulation but but in in cases cases where where the the standard A standardisrequired is very our exacting ourofsystem double(inside gaskets (inside andofoutrequired very exacting system double of gaskets and outside joint) side of joint) is recommended. is recommended.

Materials Materials The Neoferma from EPDM (Ethylene Propylene The Neoferma gasket gasketcan canbe bemanufactured manufactured from EPDM (Ethylene Propylene Diene Monomer) or neoprene or similar synthetic rubber.

Diene Monomer) or neoprene or similar synthetic rubber to suit specific Colours are available meet design criteria (subject to minimum quantity). requirements such astoexposure to hydrocarbons.

Colours are available to meet design criteria (subject to minimum quantity).

These rubbers have been in use for nearly 50 years and have an unrivalled record of durability under all kinds of conditions, including a temperature range of -350C Can be0 pproved for use in potable Water. to +90 C. These rubbers have been in use for nearly 50 years and have an unrivalled Life expectancy for EPDM is 25years and for silicon rubber, 50 years. record of durability under all kinds of conditions, including a temperature range of -350C to +1800C. www.neoferma.com www.neoferma.com

Life expectancy for EPDM is 25 years and for silicon rubber, 50 years.

www.neoferma.com

LANE COVE AQUATIC CENTRE

ROBINA TOWN CENTRE - CAR PARK

www.neoferma.com

WESTFIELD CENTRE - PARAMATTA

www.neoferma.com

E

X

P

A

N

S

I

Innovation O N J O @ I work N T

Expansion Gasket

We have been supplying Neoferma Gasket since 1982.

Using the most efficient process available we ensure that each Properties Neoferma and every batch meets theof stringent qualityGasket requirements our customers demand.

Description and Application of Neoferma We are also able to manufacture ingasket a variety of colours to suit Thedesign Neoferma gasket is suitable for sealing all types of joints. It is extremely objectives, subject to minimum quantity. flexible, consisting of hollow sections terminating in individual lips.

Projects supplied include:

Neoferma gasket is easily compressed and maintains close contact with concrete, steel, glass or wood surfaces. This ensures complete sealing of the joint.

Water and Weather resistance The gaskets have been tested successfully to a hydrostatic pressure of ten metres and in buildings more than 100m high with a wind velocity of 160km/hour developing a pressure of 130 kg/m2 and for buildings 160-320m high with a wind pressure of 180 kg/m2.

The Opera House

The Opera House Sydney Harbour Harbour Bridge Sydney Bridge Sound Insulation Parliament House -- NSW Parliament NSWsound.

These gaskets exhibit excellent insulationHouse against airborne Cahill Express Express Way Cahill Way Tunnel Tunnel Thermal Insulation The Law Law Courts Courts -- Sydney The Sydney A single gasket will provideFox good thermal insulation but in cases where the Fox Studios Studios -- Sydney Sydney standard required is very exactingRAAF our system of double gaskets (inside and Bases RAAF Bases outside of joint) is recommended.

TheOlympic Olympic Pool Pool -- Homebush The Homebush Sydney International International Airport Sydney Airport Materials Regent Shopping Centre --Malaysia Regent Shopping Malaysia The Neoferma gasket can be manufacturedCentre from EPDM (Ethylene Propylene Paya Leba Air Base Singapore Leba Air synthetic Base -rubber.

Singapore Diene Monomer) orPaya neoprene or similar Turangi Hydro Works -- New Zealand Turangi Hydro Works New Zealand Colours are available to meet design criteria (subject to minimum quantity).

Brayton Point Point Cooling Brayton CoolingTowers Towers- -USA USA These rubbers Cromwell have been in use for nearly 50 years and have an Drax Nuclear Power Station Cromwell Drax Nuclear Power Station unrivalled record of durability under all Westfieldâ&#x20AC;&#x2122;s Parramatta Westfields Parramatta ki NT NT Roads Roads ns of Robina ShoppingCentre Centre Robina Town Town Shopping Puma Petroleum

conditions, inc www.neoferma.com

www.neoferma.com

Rock & Concrete Breaking

in 3 Easy Steps

1drill

2mix 3pour

35mm 18.5mm

18.5mm

NEOFERMA AUSTRALIA PTY LTD Tel:+61 (0)7 5576 4922 Fax:+61 (0)7 5576 4933 Address: PO Box 324, West Burleigh, QLD, Australia 4219 ABN 72 094 461 042

Innovation

@ wor k